Test Report

FCC ID: XPYLISAU201

Test Report

Download: PDF
FCCID_2744387

TEST REPORT No.: 6-0082-11-1-2c According to: FCC Regulations Part 15.107&15.111, Part 15.109 Class B IC-Regulations RSS-132 Issue 2 & RSS-133 Issue 5 RSS-Gen, Issue 3 for u-blox AG RF-Data Module LISA-U200 FCC-ID: XPYLISAU200 IC-ID: 8595A-LISAU200 Laboratory Accreditation and Listings Industry Canada Voluntary Controls for Electromagnetic Emissions Reg. No.: 3462D-1 Reg. No.: 736496 Reg. No.: R-2665, R-2666 Reg. No.: 3462D-2 MRA US-EU 0003 C-2914, T-1967, G-301 Reg. No.: 3462D-3 accredited according to DIN EN ISO/IEC 17025 CETECOM GmbH Laboratory Radio Communications & Electromagnetic Compatibility Im Teelbruch 116 • 45219 Essen • Germany Registered in Essen, Germany, Reg. No.: HRB Essen 8984 Tel.: + 49 (0) 20 54 / 95 19-954 • Fax: + 49 (0) 20 54 / 95 19-964 E-mail: info@cetecom.com • Internet: www.cetecom.com Page 1 of 26 The test results relate only to the individual items which have been tested. This report shall not be reproduced in parts without the written approval of the testing laboratory © Copyright: All rights reserved by CETECOM

Test Report 6-0082-11-1-2c, Page 2 of 26 Table of contents 1. SUMMARY OF TEST RESULTS...................................................................................................................... 4 1.1. RX Mode TESTS OVERVIEW FCC Part 15 and Canada IC Standards (RSS) .............................................. 4 2. ADMINISTRATIVE DATA ............................................................................................................................... 5 2.1. Identification of the testing laboratory ............................................................................................................. 5 2.2. Test location .................................................................................................................................................... 5 2.3. Organizational items ........................................................................................................................................ 5 2.4. Applicant‟s details ........................................................................................................................................... 5 2.5. Manufacturer‟s details ..................................................................................................................................... 5 3. EQUIPMENT UNDER TEST (EUT) ................................................................................................................. 6 3.1. Additional declaration and description of main EUT ...................................................................................... 6 3.2. EUT: Type, S/N etc. and short descriptions used in this test report ................................................................ 7 3.3. Auxiliary Equipment (AE): Type, S/N etc. and short descriptions .................................................................. 7 3.4. EUT set-ups ..................................................................................................................................................... 8 3.5. EUT operating modes ...................................................................................................................................... 8 3.6. Parameter Settings on mobile phone and base station CMU200 ..................................................................... 9 4. DESCRIPTION OF TEST SET-UP’S................................................................................................................ 11 4.1. Mode Test Set-up for conducted measurements .............................................................................................. 11 4.2. Test set-up for radiated measurements ............................................................................................................ 12 5. MEASUREMENTS ............................................................................................................................................. 13 5.1. Conducted emissions on AC-Power lines ........................................................................................................ 13 5.2. Radiated field strength emissions, 30 MHz - 1 GHz ....................................................................................... 15 5.3. Radiated emissions, above 1GHz .................................................................................................................... 19 5.4. Conducted emissions on antenna port (RX-Mode) .......................................................................................... 21 5.5. Measurement uncertainties .............................................................................................................................. 23 6. ACCREDITATION DETAILS OF CETECOM’S LABORATORIES AND TEST SITES ......................... 23 7. INSTRUMENTS AND ANCILLARY ................................................................................................................ 24 7.1. Used equipment “CTC” ................................................................................................................................... 24 Table of annex Total pages SEPARATE DOCUMENT TR6-0082-11-1-2C_A1.PDF: DIAGRAMS OF TESTING 32 SEPARATE DOCUMENT TR6-0082-11-1-2C_A2.PDF: DIAGRAMS OF MEASUREMENT SETUP‟s 4 TR6-0082-11-1-2c.docx

TM Test Report 6—0082—11—1—2¢, Page 3 of26 CETECOM 1. Summary of test results The test results apply exclusively to the test samples as presented in chapter 3.1. The CETECOM GmbH does not assume responsibility for any conclusions and generalizations taken in conjunction with other specimens or samples ofthe type ofthe item presented to tests. The presented RF—Data module includes GPRS/(E)GPRS 850/1900 and W—CDMA Band II and V Band technologies. This test report shows tests results performed in IDLE Mode only. Following tests have been performed to show compliance with applicable FCC Part 15.107 class B, 15.109 class B and 15.207 (10—1—10 Edition) and RSS—Gen standards. 1.1. RX Mode TESTS OVERVIEW FCC Part 15 and Canada IC Standards (RSS) TEST CASES PORT REFERENCES & LIMITS EUT EUT Result set—up op— FCC Standard |__RSS Section TEST LIMIT mode AC—Power Lines AC— §15.107 RSS—Gen, Issue 3: FCC §15.107 Power §15.207 Chapter 7.2.4 class B limits Conducted lines §15.207 limits 3 1+2+3 p ‘ag assed Emissions +4 IC; Table 4, Chapter 724 RECEIVER Cabinet §15.109 RSS—132, FCC 15.109 + §15.33 Issue 2: 4.6 class B limits Radiated Intercon §15.35 RSS—Gen, 1+2+3 emissions necting Issue 3: 6.1 IC—limits: 1+3 £4 Passed cables Table 1, Chapter 6 (radiated) RSS—133, Issue 5: 6.6 RECEIVER Antenna §2.1051 RSS—Gen: 6.2 IC: <2 nW/AkHz terminal §15.111 RSS—132: 4.6 (abefcioO0Milts) 2 1+2+3 Passed Conducted fomtcet RSS—133: 6.7(b) <SnW/AkHz +4 emissions (6 16e Remark: —— ATTESTATION: 1 declare that all measurements were performed by me or under my supervision and that all measurements have been performed and are correctto my best knowledge and belief to Industry Canada standards. All requirements as shown in above table are met in accordance with enumerated standards. cE eTE CCOM GmbH Dipl.—Ing. Ch. Lorenz Im Teelbruch 116 Responsible for test section _ 15219 Essen Tel.: + 49 (0) 20 54 /95 19 — j Fax: + 49 (0) 20 54795 19 . no7 TR6—0082—1 1—1—2c.doex

Test Report 6-0082-11-1-2c, Page 4 of 26 2. Administrative Data 2.1. Identification of the testing laboratory Company name: CETECOM GmbH Address: Im Teelbruch 116 45219 Essen - Kettwig Germany Responsible for testing laboratory: Dipl.-Ing. W. Richter Deputy: Dipl.-Ing. J. Schmitt Laboratory accreditations/Listings: DAkkS-Registration No. D-PL-12047-01-01 FCC-Registration No.: 736496, MRA US-EU 0003 IC-Registration No. 3462D-1, 3462D-2, 3462D-3 VCCI Reg. No. R-2665, R-2666, C-2914, T-1967, G-301 2.2. Test location 2.2.1. Test laboratory “CTC” Company name: see chapter 2.1. Identification of the testing laboratory 2.3. Organizational items Order No.: E600082001 Responsible for test report and project leader: Dipl.-Ing. B. Taslica Receipt of EUT: 2011-10-26 Date(s) of test: 2011-10-26 - 2011-11-15 Date of report: 2011-11-30 ----------------------------------------------------------------------------------------------------------------------------------------------------- Version of template: 11.05 _All.Dotm 2.4. Applicant’s details Applicant‟s name: u-blox AG Address: Zürcherstrasse 68 8800 Thalwil Switzerland Contact person: Mr. Andreas Thiel 2.5. Manufacturer’s details Manufacturer‟s name: please see Applicant's details Address: please see Applicant's details TR6-0082-11-1-2c.docx

Test Report 6-0082-11-1-2c, Page 5 of 26 3. Equipment under test (EUT) 3.1. Additional declaration and description of main EUT Main function GPRS/E-GPRS/UMTS RF Module Type RF data module TX-frequency range GSM 850: 824 – 849MHz (Uplink), 869-894MHz (Downlink) GSM1900: 1850-1910MHz (Uplink), 1930-1990MHz (Downlink) FDD Band 2: 1852.4–1907.6 MHz (Uplink), 1930-1990MHz (Downlink) FDD Band 5: 826.4-846.6 MHz (Uplink), 869-894MHz (Downlink) Type of modulation GSM-mode: GMSK GPRS-Mode: 8-PSK FDD-Mode Release99: QPSK FDD Mode Release 5+6: 16QAM additionally Number of channels GSM 850: 128 – 251, 125 channels GSM1900: 512 – 810, 300 channels FDD Band 2: UARFCN range 9262 – 9400 – 9538 FDD Band 5: UARFCN range 4132 – 4183 – 4233 EMISSION DESIGNATOR(S) [GSM] 247KGXW (GPRS850) 250KGXW (EDGE850) 247KG7W (GPRS1900) 256KG7W (EDGE 1900) EMISSION DESIGNATOR(S) [FDD] 4M15F9D (FDD 2) 4M15F9D (FDD 5) Antenna Type  Integrated Frequency range of antenna:  External, no RF- connector 800MHz to 2200MHz  External, separate RF-connector FCC-ID XPYLISAU200 IC 8959-LISAU200 Power supply 3.8 V DC (nominal), 3.3 V DC (minimum) and 4.4 V DC (maximum) Lowest radio frequency signal Master clock 26 MHz Special EMI components -- EUT sample type  Production  Pre-Production  Engineering TR6-0082-11-1-2c.docx

Test Report 6-0082-11-1-2c, Page 6 of 26 3.2. EUT: Type, S/N etc. and short descriptions used in this test report Short S/N HW SW descrip- EUT Type serial number hardware status software status tion*) EUT A RF-Data Module LISA-U200 IMEI: 146001 21.03.00 35890104000 1353 EUT B RF-Data Module LISA-U200 IMEI: 146001 21.03.00 35890104000 1734 EUT C Adapter Board LISA-U200 FAE SN095 IP02_HW_CS_ -- 150000 EUT D Magnetic Mount GA.107 #1 -- -- Antenna *) EUT short description is used to simplify the identification of the EUT in this test report. 3.3. Auxiliary Equipment (AE): Type, S/N etc. and short descriptions AE S/N HW SW short Auxiliary Equipment Type serial number hardware status software status descrip- tion *) AE 1 AC/DC adaptor 0055 #1 -- -- (AC 110V/60Hz, (Power supply connected on DC 12 V) EUT B) AE 2 USB cable Mini USB to USB #1 1,8m -- AE 3 USB cable Mini USB to USB #2 1,8m -- AE 4 Laptop CTC #5 -- -- -- *) AE short description is used to simplify the identification of the auxiliary equipment in this test report. TR6-0082-11-1-2c.docx

Test Report 6-0082-11-1-2c, Page 7 of 26 3.4. EUT set-ups EUT set-up Combination of EUT and AE Remarks no.*) Set. 1 EUT A +EUT C +EUT D+AE 1 +AE 2 +AE 3 +AE 4 Used for radiated tests (Laptop on, used as interface and the display switch-off after 3 minutes) Set. 2 EUT A + EUT C Used for conducted tests (power supply cables at EUT B for nominal voltage) Set. 3 EUT B + EUT C+ EUT D+ AE 1+AE 2 +AE 3 +AE 4 Used for radiated tests (Laptop on, used as interface and the display switch-off after 3 minutes) *) EUT set-up no. is used to simplify the identification of the EUT set-up in this test report. 3.5. EUT operating modes EUT Description of operating Additional information operating modes mode no.*) GSM 850 The mobile station is synchronized to the Broadcast Control Channel op. 1 Idle mode (BCCH) and listening to the Common Control Channel (CCCH). Periodic BCCH 182 location update is disabled. GSM 1900 The mobile station is synchronized to the Broadcast Control Channel op. 2 Idle mode (BCCH) and listening to the Common Control Channel (CCCH). BCCH 651 UMTS / FDD 2 The mobile is synchronized to the UMTS base station. op. 3 IDLE-MODE UMTS / FDD 5 The mobile is synchronized to the UMTS base station. op. 4 IDLE-MODE *) EUT operating mode no. is used to simplify the test report. TR6-0082-11-1-2c.docx

Test Report 6-0082-11-1-2c, Page 8 of 26 3.6. Parameter Settings on mobile phone and base station CMU200 Following settings apply to the MS during the measurements in GSM/(E)GPRS-Mode only: Parameter Traffic Mode Idle Mode Traffic Channels mobile station (EUT) GSM 850 TCHMS= 128/ 192 /251 -- GSM 1900 TCHMS = 512 / 681 / 810 maximum power level (PCL) GSM 850: PCL = 5 (2 Watt) -- GSM 1900: PCL = 0 (1 Watt) Modulation GSM: GMSK-Modulation Scheme -- EDGE: 8-PSK Modulation Scheme DTX off -- Bitstream PRBS 2E9-1 (pseudo-random- sequence) – CCITT 0.153 Timeslot 3 Hopping off Timeslot (slot mode) GSM-Mode: single GPRS-Mode: maximum allowed uplink slots no. according MS class Maximum data transmission rate, single GPRS: 20.0 kbps/ Slot time slot EDGE: 59.2 kbps/ Slot FDD: 12.2 kbps Speech transcoding (Traffic Mode) Full rate Version 1 Mode BCCH and TCH BCCH – base station (CMU,CMD) GSM 850: 182 GSM 1900: 651 TCH – base station (CMD, CMU) auto Power level TCH – base station (used - 70 dBm timeslot level) Power level BCCH – base station - 80 dBm (control channel level) External attenuation RF/AF- Accord. calibration prior to Input/Output measurements Mobile Country Code 310 310 BS_AG_BLKS_RES 0 Paging reorganisation Off (0) Signalling channel Not applicable SDCCH Location Update Auto Cell access Disabled (barred) TR6-0082-11-1-2c.docx

Test Report 6-0082-11-1-2c, Page 9 of 26 Following settings apply to the UE (EUT) during the measurements in FDD-Mode only: Parameter Traffic Mode Idle Mode UARFCN UE Uplink (EUT) FDD 2 = 9262/ 9400/ 9538 -- (according TS34.108) FDD 5 = 4132/ 4183/ 4233 UARFCN Node B (downlink) FDD 2 = 9663/ 9800/ 9937 (according TS34.108) FDD 5 = 4358/ 4040/ 4457 UE power class Class 3 (+24dBm) HSDPA UE category/ HSUPA category 14/6 Maximum power FDD 2/4/5 12.2kbps RMC -> all TPC bits up (“1”) -- HSDPA-mode = accord. Subtests 1,2,3,4 defined in 3GPP TS34.121 HSUPA mode = accord. Subtests 1,2,3,4,5 defined in 3GPP TS34.121 Modulation 12.2kbps RMC99-mode: QPSK-Modulation Scheme -- HSDPA/HSUPA = QPSK, BPSK and 16 QAM Modulation Scheme is applicable Compression mode Off -- Bitstream PRBS 2E9-1 (pseudo-random-sequence) – CCITT 0.153 Maximum data transmission rate: GPRS: 20 kbit/s Slot EDGE: 59,2 kbit/s Slot FDD: according defined UE category Node B Downlink physical channels According Table E.5.1/E.5.1A in 3GPP TS34.121 settings External attenuation RF/AF- Accord. Set-up calibration prior to measurements Input/Output Settings for CMU (general) Repetition Continuous Stop condition None Display mode Max./Min Statistic Count 1000 Bursts Decoder Standard Additional settings on the base stations CMU200 for frequency stability measurements TR6-0082-11-1-2c.docx

Test Report 6-0082-11-1-2c, Page 10 of 26 4. DESCRIPTION OF TEST SET-UP’s 4.1. Mode Test Set-up for conducted measurements The EUT„s RF-signal is coupled out by a suitable antenna coupling connector (1). The signal is first 10 dB attenuated (2) before it is 0° divided by a power divider (3). One of the signal path is connected to the communication base station (4), other branch is connected to the spectrum – analyzer (5). The specific attenuation losses for both signal paths/branches are determined prior to the measurement within a set-up calibration. These are then taken into account by correcting the measurement readings on the spectrum-analyzer. Schematic: Test set-up conducted Following modified test set-up schematic apply for tests performed inside the climatic chamber: (Frequency stability) TR6-0082-11-1-2c.docx

Test Report 6-0082-11-1-2c, Page 11 of 26 4.2. Test set-up for radiated measurements Please see below description and schematic for radiated measurements used set-up. MEASUREMENT METHOD (30 MHz<f <1 GHz): A EMI analyzer together with a broadband antenna was used in order to identify the emissions from the EUT by positioning the antenna close to the EUT surfaces. The interconnecting cables and equipment position were varied in order to maximize the emissions. Then most critical frequencies are recorded for further investigations. Based on the exploratory measurements, the most critical frequencies are re-measured by maintaining the EUT‟s operating mode, cable position, etc. The EUT was placed on a non-conductive support of 0.8 m height. By rotating the turntable angle in the range 0 to 360 degree, the EUT itself either over 3-orthogonal axis (not defined usage position) or 2- orthogonal axis (defined usage position) and the measurement antenna height from 1 meter to 4 meters, the maximized emissions are recorded. The measurements are performed for both polarizations of the measuring antenna: horizontal and vertical. MEASUREMENT METHOD (1 GHz<f <26.5 GHz): The EUT and accessories are placed on a non-conducting tipping table of 0.8 meter height (semi-anechoic chamber) or 1.55m height (fully-anechoic chamber) which is situated in the middle of the turntable. The turntable can rotate the device under test 360 degree, the tipping table can rotate the device from laid to standing position. This way the device under test can be rotated in all three orthogonal planes in order to maximize the detected emissions. The turn- and tipping table are controlled by a controller unit. All positions manipulations are software controlled from a operator PC. The measurements are performed for both receiving antenna polarisations: vertical and horizontal. Up to 18 GHz a measurement distance of 3 meters is used, above 18 GHz the distance is 1 meter. A biconical- logarithmic antenna up to 1 GHz and a logarithmic-periodic antenna for frequencies above 1 GHz up to 26.5 GHz is used. For frequencies above 26.5 GHz a horn antenna is used, pls. compare the equipment list for more details. The EUT is powered either by a external DC-supply with nominal voltage or a AC/DC power supply as accessory. The communication signalling (if necessary for operation) is performed from outside the chamber with a communication test simulator (CMU200 from Rohde&Schwarz) and a signalling antenna place near the EUT. Schematic: radiated measurements test set-up TR6-0082-11-1-2c.docx

Test Report 6-0082-11-1-2c, Page 12 of 26 5. Measurements 5.1. Conducted emissions on AC-Power lines TEST LOCATION AND EQUIPMENT (for reference numbers please see chapter 'List of test equipment') test location  CETECOM Essen (Chapter 2.2.1)  Please see Chapter 2.2.2  Please see Chapter 2.2.3 test site  333 EMI field  348 EMI cond. receiver  001 ESS  377 ESCS 30 LISN  005 ESH2-Z5  007 ESH3-Z6  300 ESH3-Z5 & 50 used for AE  no LISN for AE signaling  392 MT8820A  436 CMU  547 CMU line voltage  230 V 50 Hz via public mains 060 110 V 60 Hz via PAS 5000 STANDARDS AND LIMITS: PART 15, SUBPART B, §15.107, §15.207, CANADA: RSS-Gen, ANSI C63.4:2009 Frequency Conducted limit Class B [MHz] [dBµV] QUASI-Peak AVERAGE 0.15 – 0.5 66 to 56* 56 to 46* 0.5 – 5 56 46 5 – 30 60 50 Remark: * decreases with the logarithm of the frequency TEST CONDITION AND MEASUREMENT PROCEDURES TEST SET-UP link to test system (if used):  air link  cable connection  EUT-grounding  none  with power supply  additional connection Equipment set up  table top  floor standing (40 cm distance to reference EUT stands isolated on reference ground plane (floor) ground plane (wall) Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)% EMI-Receiver (Analyzer) Settings Span/Range: 150 kHz to 30 MHz RBW: 9 kHz Detector/Mode: Max PEAK-hold, repetitive scan for preliminary testing Quasi-Peak Detector and Average-Detector for final measurement according ANSI 63.4, CISPR 16 Devices which can be connected to the public AC-power network, should be tested against the radio frequency voltage conducted back into the AC-power line in the frequency range 150kHz to 30 MHz. Compliance should be tested by measuring the radio frequency voltage between each power line and ground at the power terminals in the stated frequency range. A 50Ohm/50µH line impedance stabilization network (LISN) is used therefore. The EUT power input leads are connected through the LISN to the AC-power source. The LISN enclosure is electrically connected to the GND- plane. The measuring instrument is connected to the coaxial output of the LISN. Tabletop devices were set-up on a 80 cm height over reference ground plane, floor standing equipment 10 cm raised above ground plane. Measurements have been performed on each phase line and neutral line of the devices AC-power lines. The EUT was power supplied with 110 V/60Hz. The EUT was tested in the defined operating mode and installed (connected) to accessory equipment according the general description of use given by the applicant. Preliminary testing as a first step, determines the worst-case phase line (neutral or phase) as well as the most critical amplitude by changing the operating mode. A complete frequency-sweep is performed with PK-Detector. Final testing for power phases and critical frequencies (Margin to AV- or QP limit lower than 3dB) as a second step includes measurements either on discrete frequency components with receivers detector set to Quasi-Peak and Average per frequency component or a complete frequency sweep with corresponding detector. TR6-0082-11-1-2c.docx

Test Report 6-0082-11-1-2c, Page 13 of 26 MEASUREMENT RESULTS EUT Type and S/N or EUT set-up: see below EUT set-up no. EUT operating mode EUT operating mode: see below Diagram Command or Detector Power line Additional (scan-) information Result No. EUT operating mode or (Peak, (L1, L2, L3, (e.g. Pre-test Fast scan, Maxhold, (passed / operating mode no. CISPR AV, N) Final measurement) failed /final CISPR QP) measurem. necessary) a_1.1 EUT set-up 3 Peak, CISPR L1, N Pre-test Fast scan, Maxhold Passed EUT op. mode 1 AV, CISPR QP Final measurement (please see diagram) a_1.8 EUT set-up 3 Peak, CISPR L1, N Pre-test Fast scan, Maxhold Passed EUT op. mode 2 AV, CISPR QP Final measurement (please see diagram) b_1.7 EUT set-up 3 Peak, CISPR L1, N Pre-test Fast scan, Maxhold Passed EUT op. mode 4 AV, CISPR QP Final measurement (please see diagram) b_1.8 EUT set-up 3 Peak, CISPR L1, N Pre-test Fast scan, Maxhold Passed EUT op. mode 3 AV, CISPR QP Final measurement (please see diagram) Remarks: The diagram contains the maximum values from L 1 + N Margin to Limit for verdict: M  LT  R R  C Loss Abbreviations used:  RR : Receiver readings in dBµV  CLoss: cable loss  LT : Limit in dBµV VERDICT Summary of measurement results for conducted emissions on AC-Power lines: Passed TR6-0082-11-1-2c.docx

Test Report 6-0082-11-1-2c, Page 14 of 26 5.2. Radiated field strength emissions, 30 MHz - 1 GHz TEST LOCATION AND EQUIPMENT (for reference numbers please see chapter 'List of test equipment') test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA receiver  377 ESCS30  001 ESS  spectr. analys.  584 FSU  120 FSEM  264 FSEK antenna  574 BTA-L  133 EMCO3115  302 BBHA9170  289 CBL 6141  030 HFH-Z2  477 GPS signaling  392 MT8820A  436 CMU  547 CMU otherwise  400 FTC40x15E  401 FTC40x15E  110 USB LWL  482 Filter Matrix DC power  456 EA 3013A  457 EA 3013A  459 EA 2032-50  268 EA- 3050  494 AG6632A  498 NGPE line voltage  230 V 50 Hz via public mains  060 110 V 60 Hz via PAS 5000 STANDARDS AND LIMITS: CFR 47, PART 15B, §15.109, RSS-Gen, ANSI 63.4:2009 Frequency Radiated emission limits, Class B, 3 meters [MHz] QUASI-Peak QUASI-Peak [microvolts/meter] [dBµV/m] 30-88 100 40 88-216 150 43,5 216-960 200 46,0 above 960 500 54,0 TEST CONDITION AND MEASUREMENT TEST SET-UP link to test system (if used):  air link  cable connection  EUT-grounding  none  with power supply  additional connection Equipment set up  table top 0.8m height  floor standing Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)% EMI-Receiver (Analyzer) Settings Span/Range: 30 MHz to 1 GHz RBW/VBW: 120 kHz / (auto) Detector/ Mode: PEAK, TRACE max-hold mode, repetitive scan Quasi-Peak, for final measurement for critical measurements GENERAL MEASUREMENT PROCEDURES: The measurement test set-up and test procedure are in accordance with the provisions described in ANSI 63.4: 2009 The Equipment under Test (EUT) set-up to defined operating mode and installed (connected) to accessory equipment according the general description of use given by the applicant. TR6-0082-11-1-2c.docx

Test Report 6-0082-11-1-2c, Page 15 of 26 MEASUREMENT RESULTS EUT Type and S/N EUT set-up 3 EUT set-up no. Diagram Test parameter: Frequency range 30 MHz – 1000 MHz No. Op. mode Result IF Bandwidth at 6 dB: 120 kHz, Pre-measurement, variation of turntable positions Searching critical frequencies for determined critical operating mode with peak Op. mode 1 detector, repetitive scan and max-hold mode. The antenna heights are 1.0 m + 1.82 m (both heights for all measured turntable positions).  horizontal Polarisation of antenna:  vertical Final  horizontal and vertical measure-  front (0°) ment Receiving antenna directed  right (90°)  EUT tipping device in carried to EUT side:  rear (180°) vertical position (= 0°) used out a_2.01 (Turntable position during pre-  left (270°) measurement)  under (0°)  EUT tipping device in  top (180°) horiz. position (= 90°) used  no, margin to limit > 6 dB with PK detector Critical frequencies found:  yes, final measurement with QP detector carried out Step 3: Final measurement at critical frequencies (to find the worst case with Peak and CISPR QP detector) Antenna height:  moved from 1.0 m to 4.0 m continuously passed Turntable:  turned from 0° to 360° continuously EUT Tipping device: no Remarks: Please see diagram attached at annex 1.  Mounting position / usual operating position is defined => under and top side of EUT are not measured EUT Type and S/N EUT set-up 3 EUT set-up no. Diagram Test parameter: Frequency range 30 MHz – 1000 MHz No. Op. mode Result IF Bandwidth at 6 dB: 120 kHz, Pre-measurement, variation of turntable positions Searching critical frequencies for determined critical operating mode with peak Op. mode 2 detector, repetitive scan and max-hold mode. The antenna heights are 1.0 m + 1.82 m (both heights for all measured turntable positions).  horizontal Polarisation of antenna:  vertical Final  horizontal and vertical measure-  front (0°) ment Receiving antenna directed  right (90°)  EUT tipping device in carried to EUT side:  rear (180°) vertical position (= 0°) used out a_2.02 (Turntable position during pre-  left (270°) measurement)  under (0°)  EUT tipping device in  top (180°) horiz. position (= 90°) used  no, margin to limit > 6 dB with PK detector Critical frequencies found:  yes, final measurement with QP detector carried out Step 3: Final measurement at critical frequencies (to find the worst case with Peak and CISPR QP detector) Antenna height:  moved from 1.0 m to 4.0 m continuously passed Turntable:  turned from 0° to 360° continuously EUT Tipping device: no Remarks: Please see diagram attached at annex 1.  Mounting position / usual operating position is defined => under and top side of EUT are not measured TR6-0082-11-1-2c.docx

Test Report 6-0082-11-1-2c, Page 16 of 26 EUT Type and S/N EUT set-up 3 EUT set-up no. Diagram Test parameter: Frequency range 30 MHz – 1000 MHz No. Op. mode Result IF Bandwidth at 6 dB: 120 kHz, Pre-measurement, variation of turntable positions Searching critical frequencies for determined critical operating mode with peak Op. mode 3 detector, repetitive scan and max-hold mode. The antenna heights are 1.0 m + 1.82 m (both heights for all measured turntable positions).  horizontal Polarisation of antenna:  vertical Final  horizontal and vertical measure-  front (0°) ment Receiving antenna directed  right (90°)  EUT tipping device in carried to EUT side:  rear (180°) vertical position (= 0°) used out b_2.02 (Turntable position during pre-  left (270°) measurement)  under (0°)  EUT tipping device in  top (180°) horiz. position (= 90°) used  no, margin to limit > 6 dB with PK detector Critical frequencies found:  yes, final measurement with QP detector carried out Step 3: Final measurement at critical frequencies (to find the worst case with Peak and CISPR QP detector) Antenna height:  moved from 1.0 m to 4.0 m continuously passed Turntable:  turned from 0° to 360° continuously EUT Tipping device: no Remarks: Please see diagram attached at annex 1.  Mounting position / usual operating position is defined => under and top side of EUT are not measured EUT Type and S/N EUT set-up 3 EUT set-up no. Diagram Test parameter: Frequency range 30 MHz – 1000 MHz No. Op. mode Result IF Bandwidth at 6 dB: 120 kHz, Pre-measurement, variation of turntable positions Searching critical frequencies for determined critical operating mode with peak Op. mode 4 detector, repetitive scan and max-hold mode. The antenna heights are 1.0 m + 1.82 m (both heights for all measured turntable positions).  horizontal Polarisation of antenna:  vertical Final  horizontal and vertical measure-  front (0°) ment Receiving antenna directed  right (90°)  EUT tipping device in carried to EUT side:  rear (180°) vertical position (= 0°) used out b_2.01 (Turntable position during pre-  left (270°) measurement)  under (0°)  EUT tipping device in  top (180°) horiz. position (= 90°) used  no, margin to limit > 6 dB with PK detector Critical frequencies found:  yes, final measurement with QP detector carried out Step 3: Final measurement at critical frequencies (to find the worst case with Peak and CISPR QP detector) Antenna height:  moved from 1.0 m to 4.0 m continuously passed Turntable:  turned from 0° to 360° continuously EUT Tipping device: no Remarks: Please see diagram attached at annex 1.  Mounting position / usual operating position is defined => under and top side of EUT are not measured TR6-0082-11-1-2c.docx

Test Report 6-0082-11-1-2c, Page 17 of 26 Margin to Limit: Abbreviations used: M  LT  RR  C F  DF  RR : Receiver readings in dBµV/m  CF: Transducer in dB = AF (antenna factor) + CL  LT  RR   AFANTENNA  Cable LOSS   DF (cable loss)  DF : distance correction factor (if different Remark: positive margin means passed result measurement distance used than specified in the standard  LT : Limit in dBµV/m VERDICT Summary of measurement results for radiated emissions above 30 MHz and below 1 GHz : Passed TR6-0082-11-1-2c.docx

Test Report 6-0082-11-1-2c, Page 18 of 26 5.3. Radiated emissions, above 1GHz TEST LOCATION AND EQUIPMENT (for reference numbers please see chapter 'List of test equipment') test site  441 EMI SAR  348 EMI cond.  443 EMI FAR  347  337 OATS Radio.lab.  equipment  331 HC 4055      spectr. analys.  584 FSU  120 FSEM  264 FSEK  489 ESU   antenna meas  574 BTA-L  289 CBL 6141  608 HL 562  549 HL025  302 BBHA9170  477 GPS antenna meas  123 HUF-Z2  132 HUF-Z3  030 HFH-Z2    antenna subst  071 HUF-Z2  020 EMCO3115  063 LP 3146  303 BBHA9170   power meter  009 NRV  010 URV5-Z2  011 URV5-Z2    signalgener.  008 SMG  140 SMHU  263 SMP04    power meter  262 NRV-S  266 NRV-Z31  265 NRV-Z33  261 NRV-Z55  356 NRV-Z1  multimeter  341 Fluke 112      signaling  392 MT8820A  436 CMU  547 CMU DCpower  086 LNG50-10  087 EA3013  354 NGPE 40  349 car battery  350 Car battery  line voltage  230 V 50 Hz via public mains 060 110 V 60 Hz via PAS 5000 STANDARDS AND LIMITS: CFR 47, §15.109 (CLASS B), RSS-Gen, ANSI C63.4:2009 Frequency Radiated emission limits, 3 meters measurement distance [MHz] AV AV Peak Peak [microvolts/meter] [dBµV/m] [microvolts/meter] [dBµV/m] above 1GHz 500 54.0 5000 74.0 TEST CONDITION AND MEASUREMENT TEST SET-UP link to test system (if used):  air link  cable connection  EUT-grounding  none  with power supply  additional connection Equipment set up  table top 1.5m height  floor standing Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)% Spectrum-Analyzer settings Span/Frequency range : GSM850: 1..12.75 GHz +single frequencies determined in step 1GSM1900: 1..18GHz+single frequencies determined in step 1 RBW/VBW: 1 MHz / 3 MHz Detector/ Mode: Peak, MAX-hold, repetitive scan for exploratory measurement PEAK/ AVERAGE, for final measurement for critical frequencies Antenna Polarisation Horizontal / Vertical GENERAL MEASUREMENT PROCEDURES: The measurement test set-up and test procedure are in accordance with the provisions described in ANSI 63.4: 2009 (RX) The Equipment under Test (EUT) was placed on a non-conductive positioning table of 0.8 or 1.5 meter height depending from the frequency range. The measuring distance was set to 3 meter for frequencies up to 18GHz and 1 meter above 18GHz. The EUT was set-up to defined operating mode and installed (connected) to accessory equipment according the general description of use given by the applicant. For the upper frequency measurement range, it was assumed that the highest frequency generated in the device is same as the highest operable TX-frequency in GSM850 or GSM1900 Mode (848.8MHz or 1909.8 MHz). For practical reasons the upper frequency limit was set to 5 GHz or respective 10 GHz. 1. Step exploratory measurement: see above description as in the frequency range lower 1GHz. 2. Step Final Measurement(1 GHz<f <18 GHz): On the Worst-Case EUT configuration, frequency components with a margin lower than 6 dB to the limits, will be re-measured by maintaining the EUT‟s operating mode, cable position, etc.. For find the worst-case emission, the turntable was changed in the range 0 to 360 degree and the EUT itself either over 3-orthogonal axis (not defined usage position) or 2-orthogonal axis (defined usage position). The measurements are performed for both polarizations of the measuring antenna: horizontal and vertical. TR6-0082-11-1-2c.docx

Test Report 6-0082-11-1-2c, Page 19 of 26 Set-up No.: EUT set-up 1 Operating Mode: Op. mode 1 Dia- Start- Stop- MaxPeak Meas. Bandwidth Antenna Polarity Turntable Corr. Margin Limit gram Frequenc Frequency Time height position (dB) (dB) no. y (MHz) (dBµV/m) (MHz) (dBµV/m) (ms) (kHz) (cm) (deg) (CF) (M) (LT) a_5.01 1000 2800 Please see diagram Passed a_5.02 1000 5000 Please see diagram Passed Set-up No.: EUT set-up 1 Operating Mode: Op. mode 2 Dia- Start- Stop- MaxPeak Meas. Bandwidth Antenna Polarity Turntable Corr. Margin Limit gram Frequenc Frequency Time height position (dB) (dB) no. y (MHz) (dBµV/m) (MHz) (dBµV/m) (ms) (kHz) (cm) (deg) (CF) (M) (LT) a_5.09 1000 2800 Please see diagram Passed a_5.10 1000 10000 Please see diagram Passed Set-up No.: EUT set-up 1 Operating Mode: Op. mode 3 Dia- Start- Stop- MaxPeak Meas. Bandwidth Antenna Polarity Turntable Corr. Margin Limit gram Frequenc Frequency Time height position (dB) (dB) no. y (MHz) (dBµV/m) (MHz) (dBµV/m) (ms) (kHz) (cm) (deg) (CF) (M) (LT) a_5.17 1000 2800 Please see diagram Passed a_5.18 1000 10000 Please see diagram Passed Set-up No.: EUT set-up 1 Operating Mode: Op. mode 4 Dia-gram Start- Stop- MaxPeak Meas. Bandwidth Antenna Polarity Turntable Corr. Margin Limit no. Frequen Frequency Time height position (dB) (dB) cy (MHz) (dBµV/m) (MHz) (dBµV/m) (ms) (kHz) (cm) (deg) (CF) (M) (LT) b_5.19 1000 5000 Please see diagram Passed General remarks: At all diagrams only noise-floor visible (except down link channel of FDD II: a_5.18). Margin to Limit: Abbreviations used: M  LT  RR  C F  DF  RR : Receiver readings in dBµV/m   LT  RR   AFANTENNA  CableLOSS   DF CF: Transducer in dB = AF (antenna factor) + CL (cable loss)  DF : distance correction factor (if different measurement Remark: positive margin means passed result distance used than specified in the standard  LT : Limit in dBµV/m VERDICT Summary of measurement results for radiated emissions above 1 GHz : Passed TR6-0082-11-1-2c.docx

Test Report 6-0082-11-1-2c, Page 20 of 26 5.4. Conducted emissions on antenna port (RX-Mode) Test location and equipment (for reference numbers please see chapter 'List of test equipment') test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA  337 OATS  347 Radio.lab.   receiver  377 ESCS30  001 ESS  ESU    spectr. analys.  574 FSU  120 FSEM  264 FSEK    signaling  392 MT8820A  436 CMU  547 CMU power supply  456 EA 3013A  457 EA 3013A  459 EA 2032-50  268 EA- 3050  494 AG6632A  498 NGPE 40 otherwise  400 FTC40x15E  401 FTC40x15E  110 USB LWL  482 Filter Matrix line voltage  230 V 50 Hz via public mains 060 110 V 60 Hz via PAS 5000 Standards and Limits: CFR 47, §15.111(a), RSS-132, RSS-133, RSS-Gen Standard conducted emission limits on antenna port Value / [nW] Value / [dBm] FCC: §15.111(a) 2 nW for all frequencies -57 dBm RSS-Gen 2 nW below 1GHz -57 dBm RSS-132 5 nW about 1GHz -53 dBm RSS-133 Test condition and measurement test set-up link to test system (if used):  Air-link  cable connection Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)% EMI-Receiver (Analyzer) Settings Please see diagram GENERAL MEASUREMENT PROCEDURES: The measurement test set-up and test procedure are in accordance with the provisions described in ANSI C63.4: 2009 The Equipment under Test (EUT) set-up to defined operating mode and installed (connected) to accessory equipment according the general description of use given by the applicant. The test set-up 2 for conducted measurements was used 5.4.1. Conducted emissions on antenna port, §15.111(a) and Canada requirements, RSS-132, Issue 2, §4.6 5.4.1.1. IDLE GSM850 BCCH channel = 182 (Downlink) Frequency Level Margin Correction factor Result Result Limit Diagram of emission IC for Canada only FCC IC Verdict number (RBW:3kHz-> [MHz] [dBm] [dB] 4kHz) [dBm] [dBm] [dBm] a_4.33 -- -- -- <-79.0 <-80.25 -57 Passed 1.) + 1.25 dB a_4.34 4085.6 -70.61 18.86 -70.61 -71.86 -53 Passed Remark: Please see diagrams in Annex A1 for more details 1.) Peak from measurement set-up, BCCH carrier of base station TR6-0082-11-1-2c.docx

Test Report 6-0082-11-1-2c, Page 21 of 26 5.4.1.2. IDLE W-CDMA Band V BCCH channel = 4400 Frequency Level Margin Correction factor Result Result Limit Diagram of emission IC for Canada only FCC IC Verdict number (RBW:3kHz-> [MHz] [dBm] [dB] 4kHz) [dBm] [dBm] [dBm] b_4.17 -- -- -- <-80.0 <-81.25 -57 Passed1.) + 1.25 dB b_4.18 1752.8 -78.06 26.31 -78.06 -79.31 -53 Passed Remark: Please see diagrams in separated Annex A1 for more details 1.) Peak from measurement set-up, BCCH carrier of base station 5.4.2. Conducted emissions on antenna port, Canada requirements, RSS-133, Issue 5, §6.6 5.4.2.1. IDLE GSM 1900 BCCH channel = 651 (downlink) Frequency Level Margin Correction factor Result Result Limit Diagram of emission IC for Canada only FCC IC Verdict number (RBW:3kHz-> [MHz] [dBm] [dB] 4kHz) [dBm] [dBm] [dBm] a_4.31 966.15 -79.64 23.89 <-79.64 <-80.89 -57 Passed + 1.25 dB a_4.32 -- -- -- <-69.0 <-70.25 -53 Passed 1.) Remark: Please see diagrams in separated Annex A1 for more details 1.) Peak from measurement set-up, BCCH carrier of base station 5.4.2.2. IDLE W-CDMA Band II BCCH channel = 9400 Level Margin Correction factor Result Result Limit Frequency Diagram IC for Canada only FCC IC of emission Verdict number (RBW:3kHz-> [MHz] [dBm] [dB] 4kHz) [dBm] [dBm] [dBm] b_4.29 762.25 -80.1 24.35 <-80.1 <-81.35 -57 Passed + 1.25 dB b_4.30 -- -- -- <-69.0 <-70.25 -53 Passed 1.) Remark: Please see diagrams in separated Annex A1 for more details 1.) Peak from measurement set-up, BCCH carrier of base station Verdict Summary of conducted measurement on antenna port: Passed TR6-0082-11-1-2c.docx

Test Report 6-0082-11-1-2c, Page 22 of 26 5.5. Measurement uncertainties The reported uncertainties are calculated based on the standard uncertainty multiplied with the appropriate coverage factor k, such that a confidence level of approximately 95% is achieved. For uncertainty determination, each component used in the concrete measurement set-up was taken in account and it‟s contribution to the overall uncertainty according it‟s statistical distribution calculated. Following table shows expectable uncertainties for each measurement type performed. Calculated uncertainty based Measurement Frequency range Remarks: on a confidence level of 95% RF-Power Output 9 kHz .. 20 GHz 1.0 dB -- conducted RF-Power Output 30 MHz .. 4 GHz 3.17 dB Substitution method radiated Conducted RF-emissions 9 kHz .. 20 GHz 1.0 dB -- on antenna ports 150 kHz .. 30 MHz 5.0 dB Magnetic field Radiated RF-emissions 30 MHz .. 1 GHz 4.2 dB E-Field enclosure 1 GHz .. 18GHz 4.8 dB E-Field 1 GHz .. 20 GHz 3.17 dB Substitution method Occupied bandwidth 9 kHz .. 4 GHz 0.1272 ppm Frequency error (Delta Marker method) 1 dB Power Emission bandwidth 9 kHz .. 4 GHz 0.1272 ppm Frequency error (Delta Marker method) 1 dB Power Frequency stability 9 kHz .. 20 GHz 0.0636 ppm -- Conducted emissions 9 kHz .. 150 kHz 4.0 dB -- on AC-mains port 150 kHz .. 30 MHz 3.6 dB (UCISPR) Table : measurement uncertainties, valid for conducted/radiated measurements 6. Accreditation details of CETECOM’s laboratories and test sites Ref.-No. Accreditation Accreditation Body Valid for laboratory area or test site Certificate - D-PL-12047-01-01 All laboratories and test sites of CETECOM GmbH, Essen DAkkS, Deutsche Akkreditierungsstelle GmbH 337 Radiated Measurements 30 MHz to 1 GHz, 3m+10m OATS 487 Radiated Measurements 30 MHz to 1 GHz, 3m SAR 558 Radiated Measurements above 1 GHz, 3 m Fully Anechoic FCC, Federal Communications Commission 736496 Chamber Laboratory Division, USA 348 Mains Ports Conducted Interference Measurements (MRA US-EU 0003) 348 Telecommunication Ports Conducted Interference Measurements 337 3462D-1 Radiated Measurements 30 MHz to 1 GHz, 3m + 10m OATS 487 3462D-2 Radiated Measurements 30 MHz to 1 GHz, 3m SAR IC, Industry Canada Certification and Engineering 550 3462D-2 Radiated Measurements 1 GHz to 6 GHz, 3m SAR Bureau 558 Radiated Measurements above 1 GHz ,3 m Fully Anechoic 3462D-3 Chamber 337 R-2665 Radiated Measurements 30 MHz to 1 GHz, 3m+10m OATS 487 R-2666 Radiated Measurements 30 MHz to 1GHz, 3m SAR 550 G-301 Radiated Measurements 1GHz to 6 GHz, 3m SAR VCCI, Voluntary Control Council for Interference 348 C-2914 Mains Ports Conducted Interference Measurements by Information Technology Equipment, Japan 348 Telecommunication Ports Conducted Interference T-1967 Measurements TR6-0082-11-1-2c.docx

Test Report 6-0082-11-1-2c, Page 23 of 26 7. Instruments and Ancillary 7.1. Used equipment “CTC” The “Ref.-No” in the left column of the following tables allows the clear identification of the laboratory equipment. 7.1.1. Test software and firmware of equipment Ref.-No. Equipment Type Serial-No. Version of Firmware or Software during the test 001 Emi Test Receiver ESS 825132/017 Firm.= 1.21 , OTP=2.0, GRA=2.0 012 Signal Generator (EMS-cond.) SMY 01 839069/027 Firm.= V 2.02 013 Power Meter (EMS cond.) NRVD 839111/003 Firm.= V 1.51 017 Digital Radiocommunication Tester CMD 60 M 844365/014 Firmware = V 3.52 .22.01.99, DECT = D2.87 13.01.99 053 Audio Analyzer UPA3 860612/022 Firm. V 4.3 119 RT Harmonics Analyzer dig. Flickermeter B10 G60547 Firm.= V 3.1DHG 140 Signal Generator SMHU 831314/006 Firm.= 3.21 261 Thermal Power Sensor NRV-Z55 825083/0008 EPROM-Datum 02.12.04, SE EE 1 B 262 Power Meter NRV-S 825770/0010 Firm.= 2.6 263 Signal Generator SMP 04 826190/0007 Firm.=3.21 264 Spectrum Analyzer FSEK 30 826939/005 Bios=2.1, Analyzer= 3.20 UNIT Firmware= 4.04, SW-Main=4.04, SW-BBP=1.04, 295 Racal Digital Radio Test Set 6103 1572 SW-DSP=1.02, Hardboot=1.02, Softboot=2.02 R&S Test Firmware =3.53 /3.54 (current Testsoftw. f. 298 Univ. Radio Communication Tester CMU 200 832221/091 all band used 323 Digital Radiocommunication Tester CMD 55 825878/0034 Firm.= 3.52 .22.01.99 331 Climatic Test Chamber -40/+80 Grad HC 4055 43146 TSI 1.53 335 System-CTC-EMS-Conducted System EMS Conducted - EMC 32 V 8.40 340 Digital Radiocommunication Tester CMD 55 849709/037 Firm.= 3.52 .22.01.99 355 Power Meter URV 5 891310/027 Firm.= 1.31 365 10V Insertion Unit 50 Ohm URV5-Z2 100880 Eprom Data = 31.03.08 366 Ultra Compact Simulator UCS 500 M4 V0531100594 Firm. UCS 500=001925/3.06a02, rc=ISMIEC 4.10 371 Bluetooth Tester CBT32 100153 CBT V5,30+ SW-Option K55 377 Emi Test Receiver ESCS 30 100160 Firm.= 2.30, OTP= 02.01, GRA= 02.36 378 Broadband RF Field Monitor RadiSense III 03D00013SNO-08 Firm.= V.03D13 383 Signal Generator SME 03 842 828 /034 Firm.= 4.61 389 Digital Multimeter Keithley 2000 0583926 Firm. = A13 (Mainboard) A02 (Display) Firm.= 4.50 #005, IPL=4.01#001,OS=4.02#001, 392 Radio Communication Tester MT8820A 6K00000788 GSM=4.41#013, W-CDMA= 4.54#004, scenario= 4.52#002 R&S Test Firmware Base=5.14, Mess-Software= 436 Univ. Radio Communication Tester CMU 200 103083 GSM:5.14 WCDMA:5.14 (current Testsoftw. F. all band to be used , System EMI field (SAR) 441 CTC-SAR-EMI Cable Loss - EMC 32 Version 8.40 Cable 442 CTC-SAR-EMS System EMS field (SAR) - EMC 32 Version 8.40 System CTC-FAR-EMI- 443 CTC-FAR-EMI-RSE - Spuri 7.2.5 or EMC 32 Ver. 8.40 RSE 444 CTC-FAR-EMS field System-EMS-Field (FAR) - EMC 32 Version 8.40 R&S Test Firmware Base=5.14, GSM=5.14 460 Univ. Radio Communication Tester CMU 200 108901 WCDMA=5.14 (current Testsoftw.,f. all band to be used, 489 Emi Test Receiver ESU40 1000-30 Firmware=4.43 SP3, Bios=V5.1-16-3, Spec. =01.00 491 ESD Simulator dito ESD dito dito307022 V 2.30 524 Voltage Drop Simulator VDS 200 0196-16 Software Nr: 000037 Version V4.20a01 526 Burst Generator EFT 200 A 0496-06 Software Nr. 000034 Version V2.32 527 Micro Pulse Generator MPG 200 B 0496-05 Software-Nr. 000030 Version V2.43 528 Load Dump Simulator LD 200B 0496-06 Software-Nr. 000031 Version V2.35a01 R&S Test Firmware Base=5.14, GSM=5.14 546 Univ. Radio Communication Tester CMU 200 106436 WCDMA=5.14 (current Testsoftw.,f. all band to be used R&S Test Firmware Base=V5.1403 (current Testsoftw., 547 Univ. Radio Communication Tester CMU 200 835390/014 f. all band used, GSM = 5.14 WCDMA: = 5.14 584 Spectrum Analyzer FSU 8 100248 2.82_SP3 594 Univ. Radio Communication Tester CMW500 101757 Firmware Base=2.0.20.9, LTE=2.0.20.8. CDMA= 2.0.10 R&S Test Firmware Base=5.01, GSM=5.02 WCDMA= 597 Univ. Radio Communication Tester CMU 200 100347 not installed, Mainboard= µP1=V.850 598 Spectrum Analyzer FSEM 30 (Reserve) 831259/013 Firmware Bios 3.40 , Analyzer 3.40 Sp 2 TR6-0082-11-1-2c.docx

Test Report 6-0082-11-1-2c, Page 24 of 26 7.1.2. Single instruments and test systems Ref.-No. calibration Interval of Remark Equipment Type Serial-No. Manufacturer Cal due 001 Emi Test Receiver ESS 825132/017 Rohde & Schwarz 12 M - 31.03.2012 005 AC - LISN (50 Ohm/50µH, test site 1) ESH2-Z5 861741/005 Rohde & Schwarz 24/12 M - 31.03.2012 007 DC - LISN (50 Ohm/5µH) ESH3-Z6 892563/002 Rohde & Schwarz 24/12 M - 31.03.2012 009 Power Meter (EMS-radiated) NRV 863056/017 Rohde & Schwarz 24 M - 31.03.2013 016 Line Impedance Simulating Network Op. 24-D B6366 Spitzenberger+Spies 36 M - 31.03.2013 020 Horn Antenna 18 GHz (Subst 1) 3115 9107-3699 EMCO 36/12 M - 31.03.2013 021 Loop Antenna (H-Field) 6502 9206-2770 EMCO 36 M - 31.03.2013 030 Loop Antenna (H-field) HFH-Z2 879604/026 Rohde & Schwarz 36 M - 31.03.2012 033 RF-current probe (100kHz-30MHz) ESH2-Z1 879581/18 Rohde & Schwarz 24 M - 31.03.2013 057 relay-switch-unit (EMS system) RSU 494440/002 Rohde & Schwarz pre-m 1a 060 power amplifier (DC-2kHz) PAS 5000 B6363 Spitzenberger+Spies - 3 WRCT 1900/2200-5/40- 066 notch filter (WCDMA; FDD1) 5 Wainwright GmbH 12 M 1c 30.06.2012 10EEK 086 DC - power supply, 0 -10 A LNG 50-10 - Heinzinger Electronic pre-m 2 087 DC - power supply, 0 -5 A EA-3013 S - Elektro Automatik pre-m 2 090 Helmholtz coil: 2x10 coils in series - - RWTÜV - 4 091 USB-LWL-Converter OLS-1 007/2006 Ing. Büro Scheiba - 4 099 passive voltage probe ESH2-Z3 299.7810.52 Rohde & Schwarz 36 M - 31.03.2012 100 passive voltage probe Probe TK 9416 without Schwarzbeck 36 M - 31.03.2012 110 USB-LWL-Converter OLS-1 - Ing. Büro Scheiba - 4 119 RT Harmonics Analyzer dig. Flickermeter B10 G60547 BOCONSULT 36 M - 31.03.2013 134 horn antenna 18 GHz (Subst 2) 3115 9005-3414 EMCO 12 M - 31.03.2012 136 adjustable dipole antenna (Dipole 1) 3121C-DB4 9105-0697 EMCO 12 M - 31.03.2012 140 Signal Generator SMHU 831314/006 Rohde & Schwarz 24 M - 31.03.2012 248 attenuator SMA 6dB 2W - Radiall pre-m 2 249 attenuator SMA 10dB 10W - Radiall pre-m 2 252 attenuator N 6dB 12W - Radiall pre-m 2 256 attenuator SMA 3dB 2W - Radiall pre-m 2 257 hybrid 4031C 04491 Narda pre-m 2 260 hybrid coupler 4032C 11342 Narda pre-m 2 261 Thermal Power Sensor NRV-Z55 825083/0008 Rohde & Schwarz 24/12 M - 31.03.2012 262 Power Meter NRV-S 825770/0010 Rohde & Schwarz 24 M - 31.03.2012 263 Signal Generator SMP 04 826190/0007 Rohde & Schwarz 36 M - 31.03.2013 264 Spectrum Analyzer FSEK 30 826939/005 Rohde & Schwarz 12 M - 31.03.2014 265 peak power sensor NRV-Z33, Model 04 840414/009 Rohde & Schwarz 24 M - 31.03.2012 266 peak power sensor NRV-Z31, Model 04 843383/016 Rohde & Schwarz 24 M - 31.03.2012 267 notch filter GSM 850 WRCA 800/960-6EEK 9 Wainwright GmbH pre-m 2 268 AC/DC power supply EA 3050-A 9823636 Elektro Automatik pre-m 2 270 termination 1418 N BB6935 Weinschel pre-m 2 271 termination 1418 N BE6384 Weinschel pre-m 2 272 attenuator (20 dB) 50 W Model 47 BF6239 Weinschel pre-m 2 273 attenuator (10 dB) 100 W Model 48 BF9229 Weinschel pre-m 2 274 attenuator (10 dB) 50 W Model 47 (10 dB) 50 W BG0321 Weinschel pre-m 2 275 DC-Block Model 7003 (N) C5129 Weinschel pre-m 2 276 DC-Block Model 7006 (SMA) C7061 Weinschel pre-m 2 279 power divider 1515 (SMA) LH855 Weinschel pre-m 2 287 pre-amplifier 25MHz - 4GHz AMF-2D-100M4G-35-10P 379418 Miteq 12 M 1c 30.06.2012 291 high pass filter GSM 850/900 WHJ 2200-4EE 14 Wainwright GmbH 12 M 1c 30.06.2012 298 Univ. Radio Communication Tester CMU 200 832221/091 Rohde & Schwarz pre-m 3 300 AC LISN (50 Ohm/50µH, 1-phase) ESH3-Z5 892 239/020 Rohde & Schwarz 24/12 M - 31.03.2012 301 attenuator (20 dB) 50W, 18GHz 47-20-33 AW0272 Lucas Weinschel pre-m 2 302 horn antenna 40 GHz (Meas 1) BBHA9170 155 Schwarzbeck 36 M - 31.03.2014 303 horn antenna 40 GHz (Subst 1) BBHA9170 156 Schwarzbeck 36 M - 31.03.2014 331 Climatic Test Chamber -40/+80 Grad HC 4055 43146 Heraeus Vötsch 24 M - 30.11.2012 341 Digital Multimeter Fluke 112 81650455 Fluke 24 M - 31.03.2012 342 Digital Multimeter Voltcraft M-4660A IB 255466 Voltcraft 24 M - 31.03.2013 347 laboratory site radio lab. - - - 5 348 laboratory site EMI conducted - - - 5 354 DC - Power Supply 40A NGPE 40/40 448 Rohde & Schwarz pre-m 2 355 Power Meter URV 5 891310/027 Rohde & Schwarz 24 M - 31.03.2012 356 power sensor NRV-Z1 882322/014 Rohde & Schwarz 24 M - 31.03.2013 357 power sensor NRV-Z1 861761/002 Rohde & Schwarz 24 M - 31.03.2013 373 V-Network 5µH/50 Ohm ESH3-Z6 100535 Rohde & Schwarz 24/12 M - 31.03.2012 376 Horn Antenna 6 GHz BBHA9120 E BBHA 9120 E 179 Schwarzbeck 12 M - 31.03.2012 377 Emi Test Receiver ESCS 30 100160 Rohde & Schwarz 12 M - 31.03.2012 389 Digital Multimeter Keithley 2000 0583926 Keithley 24 M - 31.03.2013 392 Radio Communication Tester MT8820A 6K00000788 Anritsu 12 M - 31.03.2012 431 Model 7405 Near-Field Probe Set 9305-2457 EMCO - 4 436 Univ. Radio Communication Tester CMU 200 103083 Rohde & Schwarz 12 M - 31.03.2012 System EMI field (SAR) 441 CTC-SAR-EMI Cable Loss - CETECOM 12 M 5 31.08.2012 Cable TR6-0082-11-1-2c.docx

Test Report 6-0082-11-1-2c, Page 25 of 26 Ref.-No. calibration Interval of Remark Equipment Type Serial-No. Manufacturer Cal due System CTC-FAR-EMI- ETS- 443 CTC-FAR-EMI-RSE - 12 M 5 30.06.2012 RSE Lindgren/CETECOM WRCT 1850.0/2170.0- Wainwright Instruments 448 notch filter WCDMA_FDD II 5 12 M 1c 30.06.2012 5/40-10SSK GmbH WRCT 824.0/894.0-5/40- 449 notch filter WCDMA FDD V 1 Wainwright 12 M 1c 30.06.2012 8SSK 454 Oscilloscope HM 205-3 9210 P 29661 Hameg - 4 456 DC-Power supply 0-5 A EA 3013 S 207810 Elektro Automatik pre-m 2 459 DC -Power supply 0-5 A , 0-32 V EA-PS 2032-50 910722 Elektro Automatik pre-m 2 460 Univ. Radio Communication Tester CMU 200 108901 Rohde & Schwarz 12 M - 31.03.2012 463 Universal source HP3245A 2831A03472 Agilent - 4 466 Digital Multimeter Fluke 112 89210157 Fluke USA 24 M - 31.03.2012 467 Digital Multimeter Fluke 112 89680306 Fluke USA 24 M - 31.03.2012 468 Digital Multimeter Fluke 112 90090455 Fluke USA 24 M - 31.03.2012 477 ReRadiating GPS-System AS-47 - Automotive Cons. Fink - 3 480 power meter (Fula) NRVS 838392/031 Rohde & Schwarz 24 M - 31.03.2013 482 filter matrix Filter matrix SAR 1 - CETECOM (Brl) - 1d AMF-5D-02501800-25- 484 pre-amplifier 2,5 - 18 GHz 1244554 Miteq 12 M - 30.07.2012 10P System EMI field (SAR) ETS 487 System CTC NSA-Verification SAR-EMI - 12 M - 30.09.2012 NSA Lindgren/CETECOM 489 Emi Test Receiver ESU40 1000-30 Rohde & Schwarz 12 M - 31.03.2012 WRCG 1709/1786- 502 band reject filter SN 9 Wainwright pre-m 2 1699/1796- WRCG 824/849-814/859- 503 band reject filter SN 5 Wainwright pre-m 2 60/10SS WRCA 800/960-02/40- 512 notch filter GSM 850 SN 24 Wainwrght 12 M 1c 30.06.2012 6EEK HF Relais Box Keithley 517 relais switch matrix SE 04 Keithley pre-m 2 System 523 Digital Multimeter L4411A MY46000154 Agilent 24 M - 31.03.2013 529 6 dB Broadband resistive power divider Model 1515 LH 855 Weinschel pre-m 2 530 10 dB Broadband resistive power divider R 416110000 LOT 9828 - pre-m 2 546 Univ. Radio Communication Tester CMU 200 106436 R&S 12 M - 31.03.2012 547 Univ. Radio Communication Tester CMU 200 835390/014 Rohde & Schwarz 12 M - 31.03.2012 548 Digital-Barometer GBP 2300 without Greisinger GmbH 36/12 M - 31.03.2012 549 Log.Per-Antenna HL025 1000060 Rohde & Schwarz 36/12 M - 31.03.2012 552 high pass filter 2,8-18GHz WHKX 2.8/18G-10SS 4 Wainwright 12 M 1c 30.07.2012 System CTC FAR S- 558 System CTC FAR S-VSWR - CTC 24 M - 31.07.2013 VSWR 574 Biconilog Hybrid Antenna BTA-L 980026L Frankonia 36/12 M - 30.03.2013 584 Spectrum Analyzer FSU 8 100248 Rohde & Schwarz 12 M - 31.03.2012 594 Univ. Radio Communication Tester CMW500 101757 Rohde & Schwarz 24 M - 31.03.2012 597 Univ. Radio Communication Tester CMU 200 100347 Rohde & Schwarz 12 M - 31.03.2012 598 Spectrum Analyzer FSEM 30 (Reserve) 831259/013 Rohde & Schwarz 24 M - 13.01.2013 600 power meter NRVD (Reserve) 834501/018 Rohde & Schwarz 24 M - 31.03.2013 601 medium-sensitivity diode sensor NRV-Z5 (Reserve) 8435323/003 Rohde & Schwarz 24 M - 12.01.2013 602 peak power sensor NRV-Z32 (Reserve) 835080 Rohde & Schwarz 24 M - 12.01.2013 608 UltraLog-Antenna HL 562 830547/009 Rohde & Schwarz 36/12 M - 31.03.2014 611 DC power supply E3632A KR 75305854 Agilent pre-m 2 612 DC power supply E3632A MY 40001321 Agilent pre-m 2 613 Attenuator R416120000 20dB 10W Lot. 9828 Radiall pre-m 2 7.1.3. Legend Note / remarks Calibrated during system calibration: 1a System CTC-SAR-EMS (Ref.-No. 442) 1b System-CTC-EMS-Conducted (Ref.-No. 335) 1c System CTC-FAR-EMI-RSE (Ref.-No . 443) 1d System CTC-SAR-EMI (Ref.-No . 441) 1e System CTC-OATS (EMI radiated) (Ref.-No. 337) 1f System CTC-CTIA-OTA (Ref.-No . 420) 1g System CTC-FAR-EMS (Ref.-No . 444) 2 Calibration or equipment check immediately before measurement 3 Regulatory maintained equipment for functional check or support purpose 4 calibration of this equipment Ancillary equipment without has no effect calibration onmechanical e.g. measuring result equipment or monitoring equipment 5 Test System Interval of calibration 12 M 12 month TR6-0082-11-1-2c.docx

Test Report 6-0082-11-1-2c, Page 26 of 26 24 M 24 month 36 M 36 month 24/12 M Calibration every 24 months, between this every 12 months internal validation 36/12 M Calibration every 36 months, between this every 12 months internal validation Pre-m Check before starting the measurement - Without calibration TR6-0082-11-1-2c.docx


Document Created: 2011-12-22 11:51:38
Document Modified: 2011-12-22 11:51:38
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC