Modular Approval Letter

FCC ID: XPYLISAU201

Cover Letter(s)

Download: PDF
FCCID_2744346

Contact Bernhard Retka FCC Phone +49 (0) 2102 749 452 Fax +49 (0) 2102 749 350 Federal Communications Commission FCC Modular Approval Request (per DA 00-1407) FCC ID: XPYLISAU201 Requirement Statement from applicant 1. The modular transmitter must have its own RF shielding. fulfilled 2. The modular transmitter must have buffered modulation/data inputs (if fulfilled such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over- modulation. 3. The modular transmitter must have its own power supply regulation. fulfilled 4. The modular transmitter must comply with the antenna requirements of fulfilled Section 15.203 and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable).. 5. The modular transmitter must be tested in a stand-alone configuration, fulfilled i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. 7layers GmbH Borsigstraße 11 Registergericht/registered: a Bureau Veritas 40880 Ratingen, Germany Geschäftsführer/ Düsseldorf HRB 75554 Group Company T +49 (0) 2102 749 0 Managing Director: USt-Id.-Nr./VAT-No. DE203159652 F +49 (0) 2102 749 350 Dr. Harald Ansorge Steuer-Nr./TAX-No. 147/5869/0385 www.7layers.com Commerzbank AG Account No. 303 016 000 Bank Code 300 400 00 IBAN DE81 3004 0000 0303 0160 00 Swift Code COBADEFF

6. The modular transmitter must be labeled with its own FCC ID number, fulfilled and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. 7. The modular transmitter must comply with any specific rule or operating fulfilled requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. 8. The modular transmitter must comply with any applicable RF exposure fulfilled requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Name and surname of applicant (or authorized representative): Bernhard Retka Date: 2015-08-31 Signature: __ __ 7layers – a Bureau Veritas Group Company www.7layers.com 2 of 2


Document Created: 2015-09-02 19:34:08
Document Modified: 2015-09-02 19:34:08
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC