Test report

FCC ID: XPYLISAU200

Test Report

Download: PDF
FCCID_2140519

PARTIAL - T E S T R E P O R T No.: 6-0330-13-3-6a According to: FCC Regulations Part 15C, Part 22, Part 24 & Part 27 IC-Regulations RSS-132 Issue 3, RSS-133 Issue 6, RSS-139 Issue 2 RSS-Gen Issue 3 for u-blox AG RF-Module LISA-U200-01 FCC-ID: XPYLISAU200 IC: 8595A-LISAU200N Laboratory Accreditation and Listings Industry Canada Voluntary Controls for Electromagnetic Emissions Reg. No.: 3462D-1 Reg. No.: 736496 Reg. No.: 3462D-2 Reg. No.: R-2665, R-2666 MRA US-EU 0003 Reg. No.: 3462D-3 C-2914, T-1967, G-301 accredited according to DIN EN ISO/IEC 17025 CETECOM GmbH Laboratory Radio Communications & Electromagnetic Compatibility Im Teelbruch 116 • 45219 Essen • Germany Registered in Essen, Germany, Reg. No.: HRB Essen 8984 Tel.: + 49 (0) 20 54 / 95 19-954 • Fax: + 49 (0) 20 54 / 95 19-964 E-mail: info@cetecom.com • Internet: www.cetecom.com Page 1 of 31 The test results relate only to the individual items which have been tested. This report shall not be reproduced in parts without the written approval of the testing laboratory © Copyright: All rights reserved by CETECOM

Test Report 6-0330-13-3-6a, Page 2 of 31 Table of contents 1. SUMMARY OF TEST RESULTS...................................................................................................................... 3 1.1. TX mode, tests overview of US CFR (FCC) and Canada IC (RSS) Standards ............................................... 3 2. ADMINISTRATIVE DATA ............................................................................................................................... 4 2.1. Identification of the testing laboratory ............................................................................................................. 4 2.2. Test location .................................................................................................................................................... 4 2.3. Organizational items ........................................................................................................................................ 4 2.4. Applicant’s details ........................................................................................................................................... 4 2.5. Manufacturer’s details ..................................................................................................................................... 4 3. EQUIPMENT UNDER TEST (EUT) ................................................................................................................. 5 3.1. Technical data of main EUT declared by applicant ......................................................................................... 5 3.2. EUT: Type, S/N etc. and short descriptions used in this test report ................................................................ 6 3.3. Auxiliary Equipment (AE): Type, S/N etc. and short descriptions .................................................................. 6 3.4. EUT set-ups ..................................................................................................................................................... 6 3.5. EUT operating modes ...................................................................................................................................... 7 3.6. Parameter Settings on mobile phone and base station CMU200 ..................................................................... 8 4. DESCRIPTION OF TEST SYSTEM SET-UP’S .............................................................................................. 10 4.1. Test system set-up for conducted RF-measurement at antenna port ................................................................ 10 4.2. Test system set-up for radiated magnetic field measurements below 30 MHz ................................................ 11 4.3. Test system set-up for radiated spurious emission measurements ................................................................... 12 5. MEASUREMENTS ............................................................................................................................................. 13 5.1. RF Parameter – Power Conducted and Radiated - E.I.R.P. ............................................................................. 13 5.2. Radiated field strength emissions below 30 MHz ........................................................................................... 17 5.3. RF Paramater - Radiated out of Band RF emissions ....................................................................................... 23 5.4. Measurement uncertainties .............................................................................................................................. 26 6. ABBREVIATIONS USED IN THIS REPORT ................................................................................................. 26 7. ACCREDITATION DETAILS OF CETECOM’S LABORATORIES AND TEST SITES ......................... 27 8. INSTRUMENTS AND ANCILLARY ................................................................................................................ 27 8.1. Used equipment “CTC” ................................................................................................................................... 27 Table of annex Total pages ANNEX 1: MEASUREMENT DIAGRAMS 42 ANNEX 2: INTERNAL PHOTOGRAPHS OF EUT (TO BE SUPPLIED BY CUSTOMER) -- ANNEX 3: EXTERNAL PHOTOGRAPHS OF EUT 5 ANNEX 4: TEST SET-UP PHOTOGRAPHS 4 ANNEX 5: PRODUCT LABEL 1 ANNEX 6:DECLARATION OF IDENTICAL PRODUCTS 1 The listed attachments are an integral part of this report. TR6-0330-13-3-6a

Tm Test Report 6—0330—13—3—64, Page 3 of 31 c’”g OM 1. Summary of test results The test results apply exclusively to the test samples as presented in this Report. The CETECOM GmbH does not assume responsibility for any conclusions and generalizations taken in conjunction with other specimens or samples of the type of the item presented to tests. The Equipment Under Test (in this report, hereinafter referred as EUT) supports radiofrequency technologies. This test report shows results for GSM/(E)GPRS Band 850 and 1900, W—CDMA Band II, IV and V technologies only. Other implemented wireless technologies were not considered within this test report. Following tests have been performed to show compliance with applicable FCC Part 2, Part 22, Subpart H, Part 24, Subpart E (Broadband PCS) and Part 27, Subpart C of the FCC CFR 47 Rules, annual Edition 1" October 2013 and Canada RSS—132 Issue 3, RSS—133 Issue 6, RSS—139 issue 2 and RSS—Gen Issue 3 standards. 1.1. TX mode, tests overview of US CFR (FCC)and Canada IC (RSS) Standards No. of References & Limits EUT Diagram ge“ Port PUY op— Result chapter ases FCC Standard RSS Section Test limit SSH0P mode Emissions §15.207 limits _ AC—Power lines AC—Power §15.207 RSS—Gen, Issue 3: _ _ Remark 0,15—30 MHz lines " Chapter7.2.4 IC: Table 4, 1.) conducted Chapter 7.2.4 1+3+ 3 + 4+ — fr foust conducted Chind terminal §g2.1046 se NA 2 5+6+ passed 7+ 8+ 9+ 10 RSS—132: 5.4+ RF—Power §2.1046 sRsp—503: 5.13 <7 Wat (ERP) {48% (ERP/EIRP) 4 §22.913(a)(2) RSS—133:4.1/6.4+ = Cabinet "yp4g32(.) srspsi0si2 ~*Wet(ERP) _1 4+5+ passed radiated 27.50(d)(4 RSS—139: 6.4+ 275000 chspspsiz <!Wet(ERP) ~ 261]:“"51“:/‘;;5:% Antenna §§22i20(3129 Remark o & s j terminal 395 §22.917(a) RSS/Gen:4.6.1 99% Power «— — pra L) 99% Occupied §24.238(a) bandwith " §2.1051 Spurious emissions ARtenna §2.1057 RSS—132: 4.5.1 1+5+ 36x ondupion lcrminal §229!7@(b) RSS—133:6.5.1(@)(b) 43+1010g(P) dBc 1 4+ 5+ passed §24.238(a)(b) RSS—139: 6.5(i)(ii) 6+7 §27.53(G) General field c];:sx_c??i 1 2400/r(H2)puv/imz 2.x strength emissions §15.209(a) ¥ f 4000/F(kHz) pV/m 1 passed . Chapter 7.2.5, Table (9 kHz — 30 MHz) Cabinet + 5+6 30 pV/m f4%+ Inter— g , Spurious emissions connect §2,1053(a) RSS—132: 4+ 3+ 8.x radiated cables y21087 §22.917(a)(b) 451 & 452 RSS—133: 43+10log(P) dBc 1 £+7 passed §24.238(@)(b) 6.5.1(a)(b) §27.53(h)(3) RSS—139:6.50)Gi) §2.1055@)(2) . f Frequency stability Antenna §22.355, RSS'13214'3 a2opein Remark x conducted * terminal table C—1 RSS—133: 6.3 RSS—139: 63 <0.1 <20.1 ppm x x 1 §24.235, §27.54 TCO " PP General remark: GSM/(E)GPRS Band 850 and 1900 and the FDD bands 2/ 4/ 5 only partial done. Duc to customer declaration RF module LISA—U200—01 is based on parent module ofcertified LISA—U200. Please refer at annex 6 the declaration ofidentical products. Therefore spot—check tests are performed. Remark: 1.) Those tests already performed for the new activated FDD 4 band. Please refer ‘TR6—0143—12—11—2a°. A 4 si—— Dipl.—Ing. Ch. Lorenz CEkeom" i GmbH _23 Dipl—Ing. B. Taslica Responsible for test section wl Z’rzef'gbruch 116 ponsible for test report v Es E sen _Tel:+49 (C ) 20 54 / 95 19 ay: — 0 TR6—0330—13—3—6a +498 (0} 8084788 15 . es

Test Report 6-0330-13-3-6a, Page 4 of 31 2. Administrative Data 2.1. Identification of the testing laboratory Company name: CETECOM GmbH Address: Im Teelbruch 116 45219 Essen - Kettwig Germany Responsible for testing laboratory: Dipl.-Ing. N. Jeß Deputy: Dipl.-Ing. R. Acharkaoui 2.2. Test location 2.2.1. Test laboratory “CTC” Company name: see chapter 2.1. Identification of the testing laboratory 2.3. Organizational items Responsible for test report and project leader: Dipl.-Ing. B. Taslica Receipt of EUT: 2013-06-03 Date(s) of test: 2013-10-17- 2013-10-18 Date of report: 2013-10-19 ----------------------------------------------------------------------------------------------------------------------------------------------------- Version of template: 12.08 ,Bircan [CETECOM] 2.4. Applicant’s details Applicant’s name: u-blox AG Address: Zürcherstrasse 68 8800 Thalwil Switzerland Contact person: Mr. Giulio Comar 2.5. Manufacturer’s details Manufacturer’s name: please see Appllicant's details Address: please see Appllicant's details TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 5 of 31 3. Equipment under test (EUT) 3.1. Technical data of main EUT declared by applicant Main function GSM/GPRS/WCDMA RF Module (Data/Voice) Type LISA-U200-01-01 GSM/FDD Frequency range GSM 850: 824 – 849 MHz (Uplink), 869-894 MHz (Downlink) (US/Canada -bands) GSM1900: 1850-1910 MHz (Uplink), 1930-1990 MHz (Downlink) FDD Band 2: 1852.4–1907.6 MHz (Uplink), 1930-1990MHz (Downlink) FDD Band 4: 1712.4–1752.6 MHz (Uplink), 2110-2155MHZ (Downlink) FDD Band 5: 826.4-846.6 MHz (Uplink), 869-894MHz (Downlink) Type of modulation GSM, GPRS, GMSK EGPRS-Mode: 8-PSK FDD-Mode Release99: QPSK FDD Mode Release 5+6: DL 16 QAM, UL QPSK/BPSK additionally Number of channels GSM 850: 128 – 251, 125 channels (USA/Canada -bands) GSM1900: 512 – 810, 300 channels FDD Band 2: UARFCN range 9262 – 9400 – 9538 FDD Band 4: UARFCN range 1312 – 1413 – 1513 FDD Band 5: UARFCN range 4132 – 4183 – 4233 Antenna Type  Integrated  External, no RF- connector  External, separate RF-connector Antenna Gain  radiated:.3.0 dBi average gain Max. Output Power (conducted): GSM 850 32.4 dBm (PK) / 32.2 dBm (AV) EDGE 850 29.6 dBm (PK) / 27.0 dBm (AV) Max. Output Power (radiated): 850 band 32.40 dBm (PK) Max Output Power (conducted): GSM 1900 29.1 dBm (PK) / 29.0 dBm (AV) EDGE 1900 28.6 dBm (PK) / 25.8 dBm (AV) Max Output Power (radiated): 1900 band 32.10 dBm (PK) Max Output Power (radiated) 1700 band 29.2 dBm (PK) Max Output Power (conducted) FDD-Mode 2 26.0 dBm (PK) / 22.6 dBm (AV) FDD-Mode 4 26.2 dBm (PK) / 22.9 dBm (AV) FDD-Mode 5 26.4 dBm (PK) / 23.1 dBm (AV) FCC-ID XPYLISAU200 IC 8595A-LISAU200N Installed options  GSM 900 and GSM 1800 Bands (not usable in USA/Canada)  FDD VIII Bands (not usable in USA/Canada)  W-LAN, Bluetooth© wireless technologies  battery charging option  GPS (not tested within this test report)  FM-Radio (Receiver only)  NFC (not tested within this test report) Power supply  3.8 V DC (nominal), 3.4 V DC (minimum) and 4.2 V DC (maximum)  over AC/DC adapter: 120V/60 Hz Lowest radio frequency signal Master clock 26 MHz EUT sample type  Pre-Production FCC label attached  yes  no TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 6 of 31 3.2. EUT: Type, S/N etc. and short descriptions used in this test report Short S/N HW SW descrip- EUT Type serial number hardware status software status tion*) EUT A RF-Module LISA-U200-01 IMEI: 358901- 146AB2 22.90 04-594324-5 EUT B Adapter Board LISA-U200 FAE 279 IP02_HW_CS_ -- 150000 *) EUT short description is used to simplify the identification of the EUT in this test report. 3.3. Auxiliary Equipment (AE): Type, S/N etc. and short descriptions AE S/N HW SW short Auxiliary Equipment Type serial number hardware status software status descrip- tion *) AE 1 Magnetic Mount Taoglas GA.107 #1 Ant. Gain -- Antenna 3.0 dBi AE 2 Amplus AC/DC Charger with additional ferrite on NTS 30W EuP 5-12, AC-line (AC #1 -- -- max 4000mA 120V/60Hz, DC 12 V) AE 3 USB cable Mini USB to USB #1 1,8m -- AE 4 Laptop CTC #7 -- -- -- *) AE short description is used to simplify the identification of the auxiliary equipment in this test report. 3.4. EUT set-ups EUT set-up Combination of EUT and AE Remarks no.*) Set. 1 EUT A + EUT B + AE 1 + AE 2 + Used only for radiated tests (AE 3 + AE 4) (AE 3 + AE 4: used outside of the chamber) Set. 2 EUT A + EUT B Used only for conducted tests (power supply cables at EUT A for nominal voltage) *) EUT set-up no. is used to simplify the identification of the EUT set-up in this test report. TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 7 of 31 3.5. EUT operating modes GSM modes EUT Description of operating Additional information operating modes mode no.*) GSM 850 A communication link is established between the mobile station and the op. 1 TCH mode test simulator. The transmitter is operated at its maximum rated output TCH=128/192/251 power: 33 dBm (power class 4; power control level 5). The input signal to the receiver is modulated with normal test modulation. The wanted RF input signal level to the receiver of the mobile station is set to a level to provide a stable communication link. EGPRS 850 A communication link is established between the mobile station and the op. 2 TCH mode test simulator. The transmitter is operated at its maximum rated output TCH=128/192/251 power: 33 dBm (power class 4; power control level 5). USF_Duty CYCLE set to 100%, coding scheme MCS-5 for 8PSK modulation, slot 3 active, uplink gamma: 6 (27dBm). The input signal to the receiver is modulated with normal test modulation. The wanted RF input signal level to the receiver of the mobile station is set to a level to provide a stable communication link. GSM 1900 A communication link is established between the mobile station and the op. 3 TCH mode test simulator. The transmitter is operated at its maximum rated output TCH=512/661/810 power: 30 dBm (power class 1; power control level 0). The input signal to the receiver is modulated with normal test modulation. The wanted RF input signal level to the receiver of the mobile station is set to a level to provide a stable communication link EGPRS 1900 A communication link is established between the mobile station and the op. 4 TCH mode test simulator. The transmitter is operated at its maximum rated output TCH=512/661/810 power: 30 dBm (power class 1; power control level 0). USF_Duty CYCLE set to 100%, coding scheme MCS-5 for 8-PSK modulation, slot 3 active, uplink gamma: 5 (26 dBm). The input signal to the receiver is modulated with normal test modulation. The wanted RF input signal level to the receiver of the mobile station is set to a level to provide a stable communication link. *) EUT operating mode no. is used to simplify the test report. FDD modes FDD-Mode 2 op. 5 12.2 kbps RMC A communication link is established between the mobile station (UE) and the test simulator. The transmitter is operated on its maximum rated output FDD-Mode 4 power class: 24dBm. op. 6 12.2 kbps RMC The input signal to the receiver is modulated with normal test modulation. The wanted RF input signal level to the receiver of the mobile station is set FDD-Mode 5 to a level to provide a stable communication link according Table op. 7 E5.1/Table E5.1A as described in 3GPP TS34.121, Annex E. 12.2 kbps RMC FDD Mode 2 op. 8 HSUPA In addition to normal FDD-Mode, the UE was set to operate in HSDPA and FDD Mode 4 op. 9 HSUPA Mode too. Chosen settings: 12.2kbps RMC + HSPA 34.108 HSUPA This setting was chosen for all release 6 mobile equipment. FDD Mode 5 op. 10 HSUPA *) EUT operating mode no. is used to simplify the test report. TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 8 of 31 3.6. Parameter Settings on mobile phone and base station CMU200 Following settings apply to the MS during the measurements in GSM/GPRS/(E)GPRS-Mode only: Parameter Traffic Mode Idle Mode Traffic Channels mobile station (EUT) GSM 850: TCHMS= 128/ 190 /251 -- GSM 1900: TCHMS = 512 / 661 / 810 maximum power level (PCL) GSM 850: PCL = 5 (2 Watt) -- GSM 1900: PCL = 0 (1 Watt) Modulation GSM/GPRS: GMSK-Modulation Scheme -- EDGE: 8-PSK Modulation Scheme DTX off -- Bitstream PRBS 2E9-1 (pseudo-random-sequence) – CCITT 0.153 Timeslot(s) in Uplink 3 Hopping off Timeslot (slot mode) GSM-Mode: single GPRS-Mode: maximum allowed uplink slots no. according MS class MS slot class Class 12 Maximum data transmission rate, single GSM: 9,6 kbit/s Slot time slot GPRS: 17,6 kbit/s Slot EDGE: 59,2 kBit/s Slot Speech transcoding (Traffic Mode) Full rate Version 1 Speed rate 130 Kb/s Mode BCCH and TCH BCCH – base station (CMU,CMD) GSM 850: 182 GSM 1900: 651 TCH – base station (CMD, CMU) auto Power level TCH – base station (used - 70 dBm timeslot level) Power level BCCH – base station - 80 dBm (control channel level) External attenuation RF/AF- Accord. calibration prior to measurements Input/Output Mobile Country Code 310 310 Domain PS BS_AG_BLKS_RES 0 Paging reorganisation Off (0) Signalling channel Not applicable SDCCH Location Update Auto Cell access Disabled (barred) TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 9 of 31 Following settings apply to the UE (EUT) during the measurements in FDD-Mode only: Parameter Traffic Mode Idle Mode UARFCN UE Uplink (EUT) FDD 2 = 9262/ 9400/ 9538 -- (according TS34.108) FDD 4 = 1312/1413/1513 FDD 5 = 4132/ 4182/ 4233 UARFCN Node B (downlink) FDD 2 = 9663/ 9800/ 9937 (according TS34.108) FDD 4 = 1537/1675/1738 FDD 5 = 4358/ 4040/ 4457 UE power class Class 3 (+24dBm) nominal HSDPA UE category/ HSUPA category 8/6 Maximum power FDD 2/4/5 12.2kbps RMC -> all TPC bits up (“1”) -- HSDPA-mode = accord. in 3GPP TS34.108 HSUPA mode = accord. in 3GPP TS34.108 Modulation 12.2kbps RMC-mode: (UL) QPSK-Modulation -- Scheme HSDPA/HSUPA= (UL) BPSK/QPSK, (DL) 16 QAM Modulation Scheme is applicable Compression mode Off -- Bitstream PRBS 2E9-1 (pseudo-random-sequence) – CCITT 0.153 Maximum data transmission rate: GSM: 17,6 kbps Slot EDGE: 59,2 kbps Slot FDD: QPSK 5,76 Mbps (UL) 16 QAM 14,4 Mbps (DL) Node B Downlink physical channels According Table E.5.1/E.5.1A in 3GPP TS34.121 settings External attenuation RF/AF- Accord. Set-up calibration prior to measurements Input/Output TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 10 of 31 4. Description of test system set-up’s 4.1. Test system set-up for conducted RF-measurement at antenna port Specification: ANSI C63.10-2009 General Description: The EUT‘s RF-signal is first attenuated before it is connected to the spectrum – analyzer to avoid overload. The specific attenuation is determined prior to the measurement within a set-up calibration. The value is taken into account by correcting the measurement readings on the spectrum-analyzer either by a transducer factor (TDF) or an relative offset to reference level. Schematic: Testing method: According to ANSI C63.10-2009 for each individual test, see details in each chapter. TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 11 of 31 4.2. Test system set-up for radiated magnetic field measurements below 30 MHz Specification: ANSI C63.4-2009 chapter 8.2.1, ANSI C63.10-2009 chapter 6.4 General Description: Evaluating the radiated field emissions to be done first by an exploratory emissions measurement and a final measurement for most critical frequencies. The loop antenna was placed at 1 m height above ground plane and 3 m measurement distance from set-up for investigations. Because of reduced measurement distance, correction data were applied, as stated in chapter “General Limit - Radiated field strength emissions below 30 MHz“. The tests are performed in the semi anechoic room recognized by the regulatory commissions. Schematic: Testing method: Exploratory, preliminary measurement Final measurement on critical The EUT and it’s associated accessories are frequencies placed on a non-conductive position Based on the exploratory measurements, manipulator (tipping device) of 0.8 m the most critical frequencies are re- height which is placed on the turntable. By measured by main-taining the EUT’s worst- rotating the turntable (step 90°, range 0°to case operation mode, cable position, etc. 360°) and the EUT itself either on 3- orthogonal axis (portable equipment) or 2- First a frequency zoom around the critical orthogonal axis (defined operational frequency is done to locate the frequency position of EUT), the emission spectrum more precisely. After this step, for all and it’s characteristics was recorded with identified critical frequencies, the an EMI-receiver, broadband loop antenna maximum peak was determined. and software. The loop antenna was moved at least to Following parameters were varied: the 2-perpendicular axes (antenna vector in turntable angle continuously in the range 0 direction of EUT and parallel to EUT) in to 360 degree, the EUT itself either over 3- order to maximize the emissions. The orthogonal axis (not defined usage position) results are documented in a diagram. or 2-orthogonal axis (defined usage Critical frequencies (low margin to limit) position). are saved within a data reduction table for further investigations. If various operating On the determined worst-case position, a modes are supported, further investigations final measurement with necessary are made to find the worst-case of them. bandwidth and detector according standard Also the interconnection cables and eut in has been carried out. order to maximize the emissions. Formula: EC = ER + AF + CL + DF - GA AF =Antenna factor CL = Cable loss M = LT-EC DF= Distance correction factor EC = Electrical field – corrected value ER = Receiver reading GA= Gain of pre-amplifier (if used) LT = Limit M = Margin All units are dB-units, positive margin means value is below limit. Distance correction: Reference for applied correction (extrapolating) factors: IEEC Transaction EMC, Vol. 47, No. 3 , Aug. 2005, Journal Paper “Extrapolating Near- field emissions of low frequency loop transmitters”. TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 12 of 31 4.3. Test system set-up for radiated spurious emission measurements Specification: ANSI C63.4-2009 chapter 8, ANSI C63.10-2009 chapter 6.6 General Description: Evaluating the field emissions have to be done first by an exploratory emissions measurement and a final measurement for most critical frequencies. The tests are performed in a CISPR 16-4 compliant fully anechoic room (FAR) recognized by the regulatory commissions. The measurement distance was set to 3 meter for frequencies up to 20 GHz and 1 meter above 20 GHz. The horn antenna is used for frequency range 1 GHz to 40 GHz. Due to use of a fully anechoic room the measurement antennas are set to fixed antenna height of 1.55 m (no height scan necessary) and the site validation criteria accord. ANSI63.10:2009 is fulfilled. The EUT is aligned within 3 dB beam width of the measurement antenna, on big EUTs several surface measurements are performed. Schematic: Testing method: Exploratory, preliminary measurements Final measurement on critical frequencies The EUT and it’s associated accessories are Based on the exploratory measurements, the most placed on a non-conductive position manipulator critical frequencies are re-measured by main- (tipping device) of 1.55 m height which is placed taining the EUT’s worst-case operation mode, on the turntable. By rotating the turntable (range cable position, etc. 0° to 360°, step 45°) and the EUT itself either on First a frequency zoom around the critical 3-orthogonal axis (portable equipment) or 2- frequency is done to locate the frequency more orthogonal axis (defined operational position of precisely. After this step, for all identified critical EUT) the emission spectrum and it’s frequencies, the maximum peak was determined. characteristics was recorded with an EMI- Following parameters were varied: the turntable receiver, broadband antenna and software. angle continuously in the range 0 to 360 degree, The measurements are performed in horizontal the EUT itself either over 3-orthogonal axis (not and vertical polarization of the measurement defined usage position) or 2-orthogonal axis antennas. The results are documented in a (defined usage position). The measurement diagram. Critical frequencies (low margin to antenna height is fixed to 1.55 m. limit) are saved within a table for further On the determined worst-case position, a final investigations. If various operating modes are measurement with necessary bandwidth and supported, further investigations are made to find detector according standard has been carried out. the worst-case of them. Also the interconnection The readings on the spectrum analyzer are cables and equipment position were varied in corrected with conversion value between field order to maximize the emissions. strength and E(I)RP, so the readings shown are equivalent to ERP/EIRP values. Critical measurements near the limit are re-measured with a substitution method accord. ANSI/TIA/EIA 603. Formula: EC = ER + AF + CL + DF - GA (1) EC = Electrical field – corrected value ER = Receiver reading EcE(I)RP = Ec - 95.2 dB|3m M = Margin LT = Limit M = LT - EcE(I)RP AF = Antenna factor CL = Cable loss DF = Distance correction factor (if used) GA = Gain of pre-amplifier (if used) EcE(I)RP = Electrical field corrected for E(I)RP All units are dB-units, positive margin means value is below limit. TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 13 of 31 5. Measurements 5.1. RF Parameter – Power Conducted and Radiated - E.I.R.P. 5.1.1. Test location and equipment (for reference numbers please see chapter 'List of test equipment') test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA  347 Radio.lab.  420 OTA  receiver  377 ESCS30  001 ESS  489 ESU 40    spectr. analys.  584 FSU  120 FSEM  264 FSEK    antenna  574 BTA-L  133 EMCO3115  302 BBHA9170  289 CBL 6141  HFH-Z2  477 GPS signaling  392 MT8820A  436 CMU  547 CMU otherwise  400 FTC40x15E  401 FTC40x15E  110 USB LWL  482 Filter Matrix  378 RadiSense DC power  456 EA 3013A  463 HP3245A  459 EA 2032-50  268 EA- 3050  494 AG6632A  498 NGPE 40 10 dB Power otherwise  331 HC 4055  530  529  - cable OTA20 Attenuator divider line voltage  230 V 50 Hz via public mains 060 110 V 60 Hz via PAS 5000 5.1.2. Requirements  §2.1046  §22.913(a)(2) FCC  § 24.232(c)  § 27.50(d)(4)  RSS-132:4.4 + SRSP 503:5.1.3 IC  RSS-133:4.1/6.4 + SRSP-510:5.1.2;  RSS-139: 6.4+SRSP-513:5.1.2 Maximum Power Output of the mobile phone should be determined while measured radiated E(I)RP. Limit FDD Band 5: 7 Watt ERP (38.4 dBm) Limit Limit FDD Band 2: 2 Watt EIRP (33.0 dBm) Limit FDD Band 4: 1 Watt EIRP (30.0 dBm) Remark: PAR (PEAK-AVERAGE-RATIO) ≤ 13 dB 5.1.3 Test condition and measurement test set-up Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)% Test system set-up Please see chapter “Test system set-up for conducted measurements on antenna port” ANRITSU The measurements were performed with the integrated power measurement function of the „radio communication tester CMU200 from Rohde&Schwarz company. In this way spectrum-analyzers instrument limitations can be avoided or minimized. Instead, CMU manufacturers declared measurement error can be considered for this measurement. The attenuation (insertion loss) at the RF Inputs/Outputs of CMU were set according the path loss Measurement method of the test set-up, determined in a step before starting the measurements. A suitable artificial antenna or RF-connector is provided by the applicant in order to perform the conducted measurements. Any data provided with the artificial antenna or connector, have been taken in account in order to correct the measurement data. (typical 0.3dB for attenuation of antenna connector) Peak and Average Values have been recorded for each channel and band. A call was established on highest power transmit conditions in GMSK and RMC99 mode. UE is set TX mode, highest transmit power conditions, DTX, MPR or other power saving techniques have been disabled Mobile phone settings The measurements were made at the low, middle and high carrier frequencies of each of the supported operating band. Choosing three TX-carrier frequencies of the mobile phone, should be sufficient to demonstrate compliance. TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 14 of 31 5.1.8 Test results GSM/GPRS mode GMSK- Modulation 850MHz Band CS Mode 1Slot ARFCN- PAR Peak detektor RMS detektor Frequency Factor [dBm] [dBm] [MHz] [dB] Channel 128 824.2 32,4 32,2 0,2 Channel 192 837.0 32,4 32,3 0,1 Channel 251 848.8 32,3 32,2 0,1 E-GPRS mode 8-PSK 850MHz Band EGPRS (PS) ARFCN- PAR Peak detektor RMS detektor Frequency Factor [dBm] [dBm] [MHz] [dB] Channel 128 824.2 29,6 27,0 2,6 Channel 192 837 29,7 27,0 2,7 Channel 251 848.8 29,7 27,1 2,6 GSM/GPRS mode GMSK- Modulation 1900MHz Band CS Mode, 1 Slot ARFCN- PAR Peak detektor RMS detektor Frequency Factor [dBm] [dBm] [MHz] [dB] Channel 512 1850.2 28,9 28,8 0,1 Channel 661 1880.0 29,1 29 0,1 Channel 810 1909.8 29 28,8 0,2 E-GPRS mode 8-PSK 1900MHz Band EGPRS (PS) ARFCN- PAR Peak detektor RMS detektor Frequency Factor [dBm] [dBm] [MHz] [dB] Channel 512 1850.2 28,5 25,6 2,9 Channel 661 1880.0 28,6 25,8 2,8 Channel 810 1909.8 28,5 25,7 2,8 TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 15 of 31 RMC99-FDD5 ARFCN- PAR Peak detektor RMS detektor Frequency Factor [dBm] [dBm] [MHz] [dB] Channel 4132 826.4 26,0 23,1 2,9 Channel 4183 836.6 25,9 23,0 2,9 Channel 4233 846.6 25,9 23,0 2,9 HSUPA - FDD 5 ARFCN- PAR Peak detektor RMS detektor Frequency Factor [dBm] [dBm] [MHz] [dB] Channel 4132 826.4 26,4 22,5 3,9 Channel 4183 836.6 26,4 22,5 3,9 Channel 4233 846.6 26,4 22,4 4,0 RMC99 - FDD4 ARFCN- PAR Peak detektor RMS detektor Frequency Factor [dBm] [dBm] [MHz] [dB] Channel 1312 1712,4 26,0 22,9 3,1 Channel 1450 1740 26,0 22,9 3,1 Channel 1513 1752,6 25,8 22,7 3,1 HSUPA – FDD 4 ARFCN- PAR Peak detektor RMS detektor Frequency Factor [dBm] [dBm] [MHz] [dB] Channel 1312 1712,4 26,16 22,4 3,8 Channel 1450 1740 26,05 22,3 3,8 Channel 1513 1752,6 25,76 22,1 3,6 RMC99 - FDD2 ARFCN- PAR Peak detektor RMS detektor Frequency Factor [dBm] [dBm] [MHz] [dB] Channel 9262 1852,4 25,7 22,6 3,1 Channel 9400 1880.0 25,8 22,9 2,9 Channel 9538 1907,6 25,6 22,6 3,0 TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 16 of 31 HSUPA - FDD2 ARFCN- PAR Peak detektor RMS detektor Frequency Factor [dBm] [dBm] [MHz] [dB] Channel 9262 1852,4 25,7 22,1 3,7 Channel 9400 1880.0 26,0 22,2 3,8 Channel 9538 1907,6 25,8 22,0 3,8 5.1.0.1. Max. calculated ERP 850 band result Peak Output Set-up 2 & op. modes 1 Power [dBm] ERP- Limit Result Band Antenna gain [dBi] ARFCN no./ Value PK area Frequency calc. 128/ 824.2 850 3.0 32.4 35.4 38.45 dBm passed MHz 5.1.0.1.1. Max. calculated EIRP 1700 band result Peak Output Set-up 2 & op. modes 9 Power [dBm] EIRP- Limit Result Band Antenna gain [dBi] U-ARFCN no./ Value PK area Frequency calc. 1312/ 1700 3.0 26.2 29.2 30.00 dBm passed 1712.4 MHz 5.1.0.1.2. Max. calculated EIRP 1900 band result Peak Output Set-up 2 & op. modes 3 Power [dBm] EIRP- Limit Result Band Antenna gain [dBi] ARFCN no./ Value PK area Frequency calc. 1900 3.0 661/ 1880 MHz 29.1 32.1 33.00 dBm passed TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 17 of 31 5.2. Radiated field strength emissions below 30 MHz 5.2.1. Test location and equipment (for reference numbers please see chapter 'List of test equipment') test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA  347 Radio.lab.   receiver  377 ESCS30  001 ESS     spectr. analys.  584 FSU  120 FSEM  264 FSEK    antenna  574 BTA-L  133 EMCO3115  302 BBHA9170  289 CBL 6141  030 HFH-Z2  477 GPS signaling  392 MT8820A  436 CMU  547 CMU otherwise  400 FTC40x15E  401 FTC40x15E  110 USB LWL  482 Filter Matrix  378 RadiSense DC power  456 EA 3013A  457 EA 3013A  459 EA 2032-50  268 EA- 3050  494 AG6632A  498 NGPE 40 line voltage  230 V 50 Hz via public mains 060 120 V 60 Hz via PAS 5000 5.2.2. Requirements FCC Part 15, Subpart C, §15.205 & §15.209 IC RSS-Gen., Issue 3 ANSI C63.10-2009 Frequency Field strength limit Distance Remarks [MHz] [μV/m] [dBμV/m] [m] 0.009 – 0.490 2400/f (kHz) 67.6 – 20Log(f) (kHz) 300 Correction factor used due to measurement distance of 3 m 0.490 – 1.705 24000/f (kHz) 87.6 – 20Log(f) (kHz) 30 Correction factor used due to measurement distance of 3 m 1.705 – 30 30 29.5 30 Correction factor used due to measurement distance of 3 m 5.2.3.Test condition and measurement test set-up Signal link to test system (if used):  air link  cable connection  none EUT-grounding  none  with power supply  additional connection Equipment set up  table top  floor standing Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)%  9 – 150 kHz RBW/VBW = 200 Hz Scan step = 80 Hz Scan data  150 kHz – 30 MHz RBW/VBW = 9 kHz Scan step = 4 kHz  other: EMI-Receiver or Scan-Mode  6 dB EMI-Receiver Mode  3dB Spectrum analyser Mode Analyzer Settings Detector Peak (pre-measurement) and Quasi-PK/Average (final if applicable) Mode: Repetitive-Scan, max-hold Sweep-Time Coupled – calibrated display if continuous signal otherwise adapted to EUT’s individual transmission duty-cycle General measurement procedures Please see chapter “Test system set-up radiated magnetic field measurements below 30 MHz” 5.2.4. Measurement Results The results are presented below in summary form only. The EUT performed on middle channel. If critical peaks found (Margin <10 dB) the lowest and highest channels will be performed too. Table of measurement results: Set- OP- Used Diagra Carrier Channel Frequency up mode Remark detector Result m No. range no. no. Range No. P A QP 2.01 Middle 192 9 kHz-30 -- K  V   passed 2.02 Middle 661 9MHz kHz-30 --    passed 2.03 Middle 9400 9MHzkHz-30 1 1 --    passed 2.04 Middle 1413 9MHz kHz-30 --    passed 2.05 Middle 4182 9 kHz-30 --    passed TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 18 of 31 5.2.5. General Limit - Conducted out of Band RF emissions 5.2.6. Test location and equipment (for reference numbers please see chapter 'List of test equipment') test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA  337 OATS  347 Radio.lab.  443 FAR receiver  377 ESCS30  001 ESS  489 ESU spectr. analys.  584 FSU  120 FSEM  264 FSEK antenna  574 BTA-L  133 EMCO3115  302 BBHA9170  608 HL 562  549 HL025  477 GPS signaling  017 CMD 65  323 CMD 55  340 CMD 55 signaling  392 MT8820A  436 CMU  547 CMU power supply  463 HP3245A  457 EA 3013A  459 EA 2032-50  268 EA- 3050  494 AG6632A  498 NGPE 40 otherwise  529 6dB divider  530 10dB Att.  110 USB LWL  482 Filter Matrix  431 Near field line voltage  via public mains 060 120 V 60 Hz via PAS 5000 bei Bedarf andere Werte einsetzen 5.2.7. Requirements and limits  Part 2.1053(a), Part2.1057  Part 15 Subpart C, §15.209 @ frequencies defined in §15.205 FCC  Part 22 Subpart H, §22.917(a)(b  Part 24 Subpart E, §24.238(a)(b)  Part 27 Subpart C, §27.53(h)(3)  RSS-132, Issue 2: 4.5.1.1, IC  RSS-133, Issue 5: 6.5.1(a)(b)  RSS-139, Issue 2: 6.5 Condcuted emissions limits Frequency [MHz] Limit Peak [dBm] ≥ 30 -13 5.2.8. Test condition and test set-up Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)% Test system set-up Please see chapter “Test system set-up for conducted measurements on antenna port” “§ 2.1057 Frequency spectrum to be investigated. (a) In all of the measurements set forth in § 2.1051 and 2.1053, the spectrum shall be investigated from the lowest radio frequency signal generated in the equipment, without going below 9 kHz” The spectrum was scanned from 9 kHz (depend on the equipment, s. §2.1057) to the 10th harmonic of the highest frequency generated within the equipment. A PEAK detector was used Measurement method except measurements near the block-edge where a AVERAGE detector applied. A suitable artificial antenna or RF-connector is provided by the applicant in order to perform the conducted measurements. Any data provided with the artificial antenna or connector, have been taken in account in order to correct the measurement data. (typical 0.3dB for attenuation of antenna connector) Spectrum-Analyzer settings See below tables A call was established with settings according chapter “Parameter settings on mobile phone and base station CMU200” UE Power should be set to maximum, continuous transmission. DTX or other power saving Mobile phone settings techniques have been disabled The measurements were made at the low, middle and high carrier frequencies of each of the supported operating band. Choosing three TX-carrier frequencies of the mobile phone, should be sufficient to demonstrate compliance. TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 19 of 31 5.5.8.1 Settings for G850/FDDV Mode Start Stop R-BW V-BW Sweep freq. freq. time Att. Detector MHz MHz MHz MHz sec. Sweep 1 (subrange 1) 0.009 1 0.001 0.01 10 25 MaxH-PK Sweep 1 (subrange 2) 1 30 0.1 1 5 25 MaxH-PK Sweep 2 (subrange 1) 30 1000 0.1 1 10 35 MaxH-PK Sweep 2 (subrange 2) 1000 2500 1 1 15 35 MaxH-PK Sweep 2 (subrange 3) 2500 9000 1 1 60 35 MaxH-PK Sweep 3a (Block- Edge) 823 824 0.003(GSM) 0.01 30 35 MaxH-PK 0.03 (FDD) Sweep 3b (Block- Edge) 823 824 0.01 30 35 MaxH-AV Sweep 4a (Block- Edge) 850 851 0.003(GSM) 0.01 30 35 MaxH-PK 0.03 (FDD) Sweep 4b (Block- Edge) 850 851 0.01 30 35 MaxH-AV TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 20 of 31 5.5.8.2 Settings for PCS1900/FDD II/ FDD IV Mode Start Stop R-BW V-BW Sweep freq. freq. time Att. Detector MHz MHz MHz MHz sec. Sweep 1 (subrange 1) 0.009 1 0.001 0.01 10 25 MaxH-PK Sweep 1 (subrange 2) 1 30 0.1 1 5 25 MaxH-PK Sweep 2 (subrange 1) 30 1000 0.1 1 10 35 MaxH-PK Sweep 2 (subrange 2) 1000 2500 1 1 15 35 MaxH-PK Sweep 2 (subrange 3) 2500 19500 1 1 160 35 MaxH-PK Sweep 3a (Block- Edge) 1849 1850 0.01 30 35 MaxH-PK Sweep 3b (Block- Edge) 1849 1850 0.003(GSM) 0.01 30 35 MaxH-AV 0.03(FDD) Sweep 4a (Block- Edge) 1910 1911 0.01 30 35 MaxH-PK Sweep 4b (Block- Edge) 1910 1911 0.01 30 35 MaxH-AV TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 21 of 31 5.2.9. Results (conducted) The EUT emissions were measured below 30 MHz on middle channel only, due to uncritical results. If critical peaks found (Margin <20 dB) the lowest and highest channels will be performed, too. The results are presented below in summary form only. For more information please see each diagram enclosed in annex diagrams. 5.2.10. GSM/GPRS TCH 850: Op. Mode 1, Set-up 2 Transmitting channels/ frequencies: TX = 128/ 824.2 MHz, 192/ 837 MHz, 251/ 848.8 MHz Sweep no. Diagram Frequency of Range/ Frequency of Result Limit Verdict numbers emission ARFCN worst-peak level [MHz] [GHz] [dBm] [dBm] Sweep 1 36.00 0.009 to 30 Middle/192 -- <-52.00 Passed Sweep 2 36.01 30 to 9000 Low/128 -- < -26.00 Passed -13 Sweep 2 36.02 30 to 9000 Middle/192 -- < -26.00 Passed Sweep 2 36.03 30 to 9000 High/251 -- < -26.00 Passed Remark: -- 5.2.11. GSM/GPRS TCH 1900: Op. Mode 3, Set-up 2 Transmitting channels/ frequencies: TX = 512/ 1850.2 MHz, 661/ 1880 MHz, 810/ 1909.8 MHz Sweep no. Diagram Frequency of Range/ Frequency of Result Limit Verdict numbers emission ARFCN worst-peak level [MHz] [GHz] [dBm] [dBm] Sweep 1 36.07 0.009 to 30 Middle/661 -- <-51.00 Passed Sweep 2 36.08 30 to 19500 Low/512 -- < -27.00 Passed -13 Sweep 2 36.09 30 to 19500 Middle/661 -- < -27.00 Passed Sweep 2 36.10 30 to 19500 High/810 -- < -27.00 Passed Remark: -- 5.2.12. FDD II : Op. Mode 5, Set-up 2 Transmitting channels/ frequencies: TX = 9262/ 1852.4 MHz, 9400/ 1880 MHz, 9538/ 1907.6 MHz Sweep no. Diagram Frequency of Range/ Frequency of Result Limit Verdict numbers emission U-ARFCN worst-peak level [MHz] [GHz] [dBm] [dBm] Sweep 1 36.14 0.009 to 30 Middle/9400 -- <-51.00 Passed Sweep 2 36.15 30 to 19500 Low/9262 -- < -29.00 Passed -13 Sweep 2 36.16 30 to 19500 Middle/9400 -- < -30.00 Passed Sweep 2 36.17 30 to 19500 High/9538 -- < -29.00 Passed TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 22 of 31 5.2.13. FDD IV TCH : Op. Mode 6, Set-up 2 Transmitting channels/ frequencies: TX = 1312/ 1712.4 MHz, 1413/ 1732.6 MHz, 1513/ 1752.6 MHz Sweep no. Diagram Frequency of Range/ Frequency of Result Limit Verdict numbers emission U-ARFCN worst-peak level [MHz] [GHz] [dBm] [dBm] Sweep 1 36.18 0.009 to 30 Middle/1413 -- <-51.00 Passed Sweep 2 36.19 30 to 18000 Low/1312 -- < -29.00 Passed -13 Sweep 2 36.20 30 to 18000 Middle/1413 -- < -29.00 Passed Sweep 2 36.21 30 to 18000 High/1513 -- < -30.00 Passed 5.2.14. FDD V TCH : Op. Mode 7, Set-up 2 Transmitting channels/ frequencies: TX = 4132/ 826.4 MHz, 4182/ 836.4 MHz, 4233/ 846.6 MHz Sweep no. Diagram Frequency of Range/ Frequency of Result Limit Verdict numbers emission U-ARFCN worst-peak level [MHz] [GHz] [dBm] [dBm] Sweep 1 36.22 0.009 to 30 Middle/4182 -- <-51.00 Passed Sweep 2 36.23 30 to 9000 Low/4132 -- < -29.00 Passed -13 Sweep 2 36.24 30 to 9000 Middle/4182 -- < -29.00 Passed Sweep 2 36.25 30 to 9000 High/4233 -- < -30.00 Passed TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 23 of 31 5.3. RF Paramater - Radiated out of Band RF emissions 5.3.1. Test location and equipment (for reference numbers please see chapter 'List of test equipment') test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA  443 FAR  347 Radio.lab. receiver  377 ESCS30  001 ESS  489 ESU spectr. analys.  584 FSU  120 FSEM  264 FSEK antenna  608 HL 562  549 HL 025  302 BBHA9170  289 CBL 6141  030 HL-025  477 GPS signaling  017 CMD 65  323 CMD 55  340 CMD 55 signaling  392 MT8820A  546 CMU  547 CMU power supply  463 HP3245A  457 EA 3013A  459 EA 2032-50  268 EA- 3050  494 AG6632A  498 NGPE 40 otherwise  529 6dB divider  530 10dB Att.  110 USB LWL  482 Filter Matrix  431 Near field line voltage  230 V 50 Hz via public mains 060 120 V 60 Hz via PAS 5000 5.3.2. Requirements/Limits  Part 2.1053(a), Part2.1057(a)(1)  Part 15 Subpart C, §15.209 @ frequencies defined in §15.205 FCC  Part 22 Subpart H, §22.917(a)(b  Part 24 Subpart E, §24.238(a)(b)  Part 27 Subpart E, §27.53(h)(3)  RSS-132, Issue 2: 4.5.1.1, IC  RSS-133, Issue 5: 6.5.1(a)(b)  RSS-139, Issue 2: 6.5 Radiated emissions limits, 3 meters Frequency [MHz] Limit Peak [dBm] ≥ 30 -13 5.3.3. Test condition and measurement test set-up link to test system (if used):  air link  cable connection EUT-grounding  none  with power supply  additional connection Equipment set up  table top  floor standing Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)% Test system set-up Please see chapter “Test system set-up for spurious emission measurement” The spectrum was scanned from 9 kHz to the 10th harmonic of the highest frequency generated Measurement method within the equipment. A PEAK detector was used except measurements near the block-edge where a AVERAGE detector applied. Below described settings for spectrum-analyzer applies. A call was established with settings according chapter “Parameter settings on mobile phone and base station CMU200” The UE and used accessories (if any used) were set to work according their intended Mobile phone settings use/specification stated as by the applicant The measurements were made at the low, middle and high carrier frequencies of each of the supported operating band. Choosing three TX-carrier frequencies of the mobile phone, should be sufficient to demonstrate compliance. 5.3.3.1. Spectrum-Analyzer settings for GSM/GPRS/E-GPRS 850 Mode/ FDD V Mode Start Stop R-BW V-BW Sweep Att. freq. freq. time Detector [dB] MHz MHz MHz MHz sec. Sweep 1 (subrange 1) 30 1000 1 1 10 10 MaxH-PK Sweep 2 (subrange 2) 1000 2800 1 1 15 10 MaxH-PK Sweep 3 (subrange 3) 2800 9000 1 1 60 10 MaxH-PK Sweep 4a (Block-Edge) 823 824 0.003(GSM) 0.01 30 10 MaxH-PK Sweep 4b (Block-Edge) 849 850 0.03 (FDD) 0.1 30 10 MaxH-PK TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 24 of 31 5.3.3.2. Spectrum-analyzer settings for GSM/GPRS/E-GPRS 1900 Mode/ FDD II / FDD IV Mode Start Stop R-BW V-BW Sweep freq. freq. time Att. Detector MHz MHz MHz MHz sec. Sweep 1 (subrange 1) 30 1000 1 1 10 10 MaxH-PK Sweep 2 (subrange 2) 1000 2800 1 1 15 10 MaxH-PK Sweep 3 (subrange 3) 2800 20000 1 1 160 10 MaxH-PK Sweep 4a (Band-Edge) 1849 1850 0.003(GSM) 0.01 30 10 MaxH-PK Sweep 4b (Band-Edge) 1910 1911 0.03 (FDD) 0.1 30 10 MaxH-AV 5.3.4. Results spurious emissions radiated GSM and FDD modes selected which has the highest ERP and EIRP values and critical measured level (Margin < 6dB) will be notified, only. The results are presented below in summary form only. For more information please see each diagram enclosed in annex diagrams. 5.3.4.1. G850 Result Carrier Set- OP- Diagram Frequency Used detector Channel up mode Remark no. range no. no. PK AV QP 8.01 Low 1    passed Uplink carrier of    8.02 Middle 30 – 1 1 passed GSM band on 9000 MHz diagrams 8.03 High 1    passed 5.3.4.2. PCS 1900 Result Carrier Set- OP- Diagram Frequency Used detector Channel up mode Remark no. range no. no. PK AV QP 8.04 Low 3    passed 30 – Uplink carrier of 8.05 Middle 1 3    passed 18000 GSM band on MHz diagrams 8.06 High 3    passed TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 25 of 31 5.3.4.3. FDD II Result Carrier Set- OP- Diagram Frequency Used detector Channel up mode Remark no. range no. no. PK AV QP 8.20 Low 5    passed 30 – Uplink carrier of 8.21 Middle 1 5    passed 18000 FDD band on MHz diagrams 8.22 High 5    passed 5.3.4.4. FDD IV Result Carrier Set- OP- Diagram Frequency Used detector Channel up mode Remark no. range no. no. PK AV QP 8.23 Low 6    passed 30 – Uplink carrier of 8.24 Middle 1 6    passed 17000 FDD band on MHz diagrams 8.25 High 6    passed 5.3.4.5. FDD V Result Carrier Set- OP- Diagram Frequency Used detector Channel up mode Remark no. range no. no. PK AV QP 8.26 Low 7    passed 30 – Uplink carrier of 8.27 Middle 1 7    passed 9000 FDD band on MHz diagrams 8.28 High 7    passed TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 26 of 31 5.4. Measurement uncertainties The reported uncertainties are calculated based on the standard uncertainty multiplied with the appropriate coverage factor k, such that a confidence level of approximately 95% is achieved. For uncertainty determination, each component used in the concrete measurement set-up was taken in account and it’s contribution to the overall uncertainty according it’s statistical distribution calculated. Following table shows expectable uncertainties for each measurement type performed. Calculated uncertainty based RF-Measurement Frequency range Remarks: on a confidence level of 95% Power Output conducted 9 kHz .. 20 GHz 1.0 dB -- Power Output radiated 30 MHz .. 4 GHz 3.17 dB Substitution method Conducted emissions on antenna ports 9 kHz .. 20 GHz 1.0 dB -- 150 kHz .. 30 MHz 5.0 dB Magnetic field Radiated emissions enclosure 30 MHz .. 1 GHz 4.2 dB E-Field 1 GHz .. 20 GHz 3.17 dB Substitution method 9 kHz .. 4 GHz 0.1272 ppm (Delta Marker ) Frequency error Occupied bandwidth 1.0 dB Power 9 kHz .. 4 GHz 0.1272 ppm (Delta Marker) Frequency error Emission bandwidth 1.0 dB Power Frequency stability 9 kHz .. 20 GHz 0.0636 ppm -- Conducted emissions 9 kHz .. 150 kHz 4.0 dB -- on AC-mains port (UCISPR) 150 kHz .. 30 MHz 3.6 dB Table: measurement uncertainties, valid for conducted/radiated measurements 6. Abbreviations used in this report The abbreviations ANSI American National Standards Institute AV or AVG Average detector CAV Average detector EIRP Equivalent isotropically radiated power, determined within a separate measurement EGPRS Enhanced General Packet Radio Service EUT Equipment Under Test FCC Federal Communications Commission, USA IC Industry Canada n.a. not applicable Op-Mode Operating mode of the equipment PK Peak RBW resolution bandwidth RF Radio frequency RSS Radio Standards Specification, Dokuments from Industry Canada Rx Receiver TCH Traffic channel Tx Transmitter QP Quasi peak detector VBW Video bandwidth ERP Effective radiated power TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 27 of 31 7. Accreditation details of CETECOM’s laboratories and test sites Ref.- Accreditation Valid for laboratory area or test site No. Certificate Accreditation Body - D-PL- DAkkS, Deutsche All laboratories and test sites of CETECOM GmbH, Essen 12047-01-01 Akkreditierungsstelle GmbH 337 Radiated Measurements 30 MHz to 1 GHz, 3 m / 10 m (OATS) FCC, Federal Communications 487 Radiated Measurements 30 MHz to 1 GHz, 3 m (SAR) Commission 558 736496 Radiated Measurements above 1 GHz, 3 m (FAR) Laboratory Division, USA 348 Mains Ports Conducted Interference Measurements (MRA US-EU 0003) 348 Telecommunication Ports Conducted Interference Measurem. 337 3462D-1 Radiated Measurements 30 MHz to 1 GHz, 3 m / 10 m (OATS) IC, Industry Canada 487 3462D-2 Radiated Measurements 30 MHz to 1 GHz, 3 m (SAR) Certification and Engineering 550 3462D-2 Radiated Measurements 1 GHz to 6 GHz, 3 m (SAR) Bureau 558 3462D-3 Radiated Measurements above 1 GHz, 3 m (FAR) 337 R-2665 Radiated Measurements 30 MHz to 1 GHz, 3 m / 10 m (OATS) VCCI, Voluntary Control 487 R-2666 Radiated Measurements 30 MHz to 1 GHz, 3 m (SAR) Council for Interference by 550 G-301 Radiated Measurements 1 GHz to 6 GHz, 3 m (SAR) Information Technology 348 C-2914 Mains Ports Conducted Interference Measurements Equipment, Japan 348 T-1967 Telecommunication Ports Conducted Interference Measurem. OATS = Open Area Test Site, SAR = Semi Anechoic Room, FAR = Fully Anechoic Room 8. Instruments and Ancillary 8.1. Used equipment “CTC” The “Ref.-No” in the left column of the following tables allows the clear identification of the laboratory equipment. 8.1.1. Test software and firmware of equipment Ref.-No. Equipment Type Serial-No. Version of Firmware or Software during the test 001 EMI Test Receiver ESS 825132/017 Firm.= 1.21 , OTP=2.0, GRA=2.0 012 Signal Generator (EMS-cond.) SMY 01 839069/027 Firm.= V 2.02 013 Power Meter (EMS cond.) NRVD 839111/003 Firm.= V 1.51 017 Digital Radiocommunication Tester CMD 60 M 844365/014 Firmware = V 3.52 .22.01.99, DECT = D2.87 13.01.99 053 Audio Analyzer UPA3 860612/022 Firm. V 4.3 119 RT Harmonics Analyzer dig. Flickermeter B10 G60547 Firm.= V 3.1DHG 140 Signal Generator SMHU 831314/006 Firm.= 3.21 261 Thermal Power Sensor NRV-Z55 825083/0008 EPROM-Datum 02.12.04, SE EE 1 B 262 Power Meter NRV-S 825770/0010 Firm.= 2.6 263 Signal Generator SMP 04 826190/0007 Firm.=3.21 264 Spectrum Analyzer FSEK 30 826939/005 Bios=2.1, Analyzer= 3.20 UNIT Firmware= 4.04, SW-Main=4.04, SW-BBP=1.04, 295 Racal Digital Radio Test Set 6103 1572 SW-DSP=1.02, Hardboot=1.02, Softboot=2.02 R&S Test Firmware =3.53 /3.54 (current Testsoftw. f. 298 Univ. Radio Communication Tester CMU 200 832221/091 all band used 323 Digital Radiocommunication Tester CMD 55 825878/0034 Firm.= 3.52 .22.01.99 331 Climatic Test Chamber -40/+80 Grad HC 4055 43146 TSI 1.53 335 CTC-EMS-Conducted System EMS Conducted - EMC 32 V 8.52 340 Digital Radiocommunication Tester CMD 55 849709/037 Firm.= 3.52 .22.01.99 355 Power Meter URV 5 891310/027 Firm.= 1.31 365 10V Insertion Unit 50 Ohm URV5-Z2 100880 Eprom Data = 31.03.08 366 Ultra Compact Simulator UCS 500 M4 V0531100594 Firm. UCS 500=001925/3.06a02, rc=ISMIEC 4.10 371 Bluetooth Tester CBT32 100153 CBT V5,30+ SW-Option K55, K57 377 EMI Test Receiver ESCS 30 100160 Firm.= 2.30, OTP= 02.01, GRA= 02.36 378 Broadband RF Field Monitor RadiSense III 03D00013SNO-08 Firm.= V.03D13 383 Signal Generator SME 03 842 828 /034 Firm.= 4.61 389 Digital Multimeter Keithley 2000 0583926 Firm. = A13 (Mainboard) A02 (Display) Firm.= 4.50 #005, IPL=4.01#001,OS=4.02#001, 392 Radio Communication Tester MT8820A 6K00000788 GSM=4.41#013, W-CDMA= 4.54#004, scenario= 4.52#002 R&S Test Firmware Base=5.14, Mess-Software= 436 Univ. Radio Communication Tester CMU 200 103083 GSM:5.14 WCDMA:5.14 (current Testsoftw. F. all band 441 CTC-SAR-EMI Cable Loss System EMI field (SAR) - EMC 32 Version 8.52 442 CTC-SAR-EMS System EMS field (SAR) - EMC 32 Version 8.40 System CTC-FAR-EMI- 443 CTC-FAR-EMI-RSE - Spuri 7.2.5 or EMC 32 Ver. 8.53 RSE 444 CTC-FAR-EMS field System-EMS-Field (FAR) - EMC 32 Version 8.40 460 Univ. Radio Communication Tester CMU 200 108901 R&S Test Firmware Base=5.14, GSM=5.14 TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 28 of 31 Ref.-No. Equipment Type Serial-No. Version of Firmware or Software during the test WCDMA=5.14 (current Testsoftw.,f. all band to be used, 489 EMI Test Receiver ESU40 1000-30 Firmware=4.43 SP3, Bios=V5.1-16-3, Spec. =01.00 491 ESD Simulator dito ESD dito dito307022 V 2.30 524 Voltage Drop Simulator VDS 200 0196-16 Software Nr: 000037 Version V4.20a01 526 Burst Generator EFT 200 A 0496-06 Software Nr. 000034 Version V2.32 527 Micro Pulse Generator MPG 200 B 0496-05 Software-Nr. 000030 Version V2.43 528 Load Dump Simulator LD 200B 0496-06 Software-Nr. 000031 Version V2.35a01 R&S Test Firmware Base=5.14, GSM=5.14 546 Univ. Radio Communication Tester CMU 200 106436 WCDMA=5.14 (current Testsoftw.,f. all band to be used R&S Test Firmware Base=V5.1403 (current Testsoftw., 547 Univ. Radio Communication Tester CMU 200 835390/014 f. all band used, GSM = 5.14 WCDMA: = 5.14 584 Spectrum Analyzer FSU 8 100248 2.82_SP3 594 Wideband Radio Communication Tester CMW500 101757 Firmware Base=2.0.20.9, LTE=2.0.20.8. CDMA= 2.0.10 R&S Test Firmware Base=5.01, GSM=5.02 WCDMA= 597 Univ. Radio Communication Tester CMU 200 100347 not installed, Mainboard= µP1=V.850 598 Spectrum Analyzer FSEM 30 (Reserve) 831259/013 Firmware Bios 3.40 , Analyzer 3.40 Sp 2 620 EMI Test Receiver ESU 26 100362 4.43_SP3 642 Wideband Radio Communication Tester CMW 500 126089 8.1.2. Single instruments and test systems Ref.-No. calibration Interval of Remark Equipment Type Serial-No. Manufacturer Cal due 001 EMI Test Receiver ESS 825132/017 Rohde & Schwarz 12 M - 31.03.2014 005 AC - LISN (50 Ohm/50µH, test site 1) ESH2-Z5 861741/005 Rohde & Schwarz 24/12 M - 31.03.2014 007 Single-Line V-Network (50 Ohm/5µH) ESH3-Z6 892563/002 Rohde & Schwarz 24/12 M - 31.03.2014 009 Power Meter (EMS-radiated) NRV 863056/017 Rohde & Schwarz 24 M - 31.03.2014 016 Line Impedance Simulating Network Op. 24-D B6366 Spitzenberger+Spies 36 M - 31.03.2014 020 Horn Antenna 18 GHz (Subst 1) 3115 9107-3699 EMCO 36/12 M - 31.03.2014 021 Loop Antenna (H-Field) 6502 9206-2770 EMCO 36 M - 31.03.2015 030 Loop Antenna (H-field) HFH-Z2 879604/026 Rohde & Schwarz 36 M - 31.03.2015 033 RF-current probe (100kHz-30MHz) ESH2-Z1 879581/18 Rohde & Schwarz 24 M - 31.03.2014 057 relay-switch-unit (EMS system) RSU 494440/002 Rohde & Schwarz pre-m 1a 060 power amplifier (DC-2kHz) PAS 5000 B6363 Spitzenberger+Spies - 3 WRCT 1900/2200-5/40- 066 notch filter (WCDMA; FDD1) 5 Wainwright GmbH 12 M 1g 30.06.2014 10EEK 086 DC - power supply, 0 -10 A LNG 50-10 - Heinzinger Electronic pre-m 2 087 DC - power supply, 0 -5 A EA-3013 S - Elektro Automatik pre-m 2 090 Helmholtz coil: 2x10 coils in series - - RWTÜV - 4 091 USB-LWL-Converter OLS-1 007/2006 Ing. Büro Scheiba - 4 099 passive voltage probe ESH2-Z3 299.7810.52 Rohde & Schwarz 36 M - 31.03.2015 100 passive voltage probe Probe TK 9416 without Schwarzbeck 36 M - 31.03.2015 110 USB-LWL-Converter OLS-1 - Ing. Büro Scheiba - 4 119 RT Harmonics Analyzer dig. Flickermeter B10 G60547 BOCONSULT 36 M - 31.03.2014 134 horn antenna 18 GHz (Subst 2) 3115 9005-3414 EMCO 12 M - 31.03.2014 136 adjustable dipole antenna (Dipole 1) 3121C-DB4 9105-0697 EMCO 36 M - 31.03.2015 140 Signal Generator SMHU 831314/006 Rohde & Schwarz 24 M - 31.03.2014 248 attenuator SMA 6dB 2W - Radiall pre-m 2 249 attenuator SMA 10dB 10W - Radiall pre-m 2 252 attenuator N 6dB 12W - Radiall pre-m 2 256 attenuator SMA 3dB 2W - Radiall pre-m 2 257 hybrid 4031C 04491 Narda pre-m 2 260 hybrid coupler 4032C 11342 Narda pre-m 2 261 Thermal Power Sensor NRV-Z55 825083/0008 Rohde & Schwarz 24 M - 31.03.2014 262 Power Meter NRV-S 825770/0010 Rohde & Schwarz 24 M - 31.03.2014 263 Signal Generator SMP 04 826190/0007 Rohde & Schwarz 36 M - 31.03.2014 264 Spectrum Analyzer FSEK 30 826939/005 Rohde & Schwarz 12 M - 31.03.2014 265 peak power sensor NRV-Z33, Model 04 840414/009 Rohde & Schwarz 24 M - 31.03.2014 266 peak power sensor NRV-Z31, Model 04 843383/016 Rohde & Schwarz 24 M - 31.03.2014 267 notch filter GSM 850 WRCA 800/960-6EEK 9 Wainwright GmbH pre-m 2 270 termination 1418 N BB6935 Weinschel pre-m 2 271 termination 1418 N BE6384 Weinschel pre-m 2 272 attenuator (20 dB) 50 W Model 47 BF6239 Weinschel pre-m 2 273 attenuator (10 dB) 100 W Model 48 BF9229 Weinschel pre-m 2 274 attenuator (10 dB) 50 W Model 47 (10 dB) 50 W BG0321 Weinschel pre-m 2 275 DC-Block Model 7003 (N) C5129 Weinschel pre-m 2 276 DC-Block Model 7006 (SMA) C7061 Weinschel pre-m 2 279 power divider 1515 (SMA) LH855 Weinschel pre-m 2 287 pre-amplifier 25MHz - 4GHz AMF-2D-100M4G-35-10P 379418 Miteq 12 M 1c 30.06.2014 291 high pass filter GSM 850/900 WHJ 2200-4EE 14 Wainwright GmbH 12 M 1c 30.06.2014 TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 29 of 31 Ref.-No. calibration Interval of Remark Equipment Type Serial-No. Manufacturer Cal due 298 Univ. Radio Communication Tester CMU 200 832221/091 Rohde & Schwarz pre-m 3 300 AC LISN (50 Ohm/50µH, 1-phase) ESH3-Z5 892 239/020 Rohde & Schwarz 24/12 M - 31.03.2014 301 attenuator (20 dB) 50W, 18GHz 47-20-33 AW0272 Lucas Weinschel pre-m 2 302 horn antenna 40 GHz (Meas 1) BBHA9170 155 Schwarzbeck 36 M - 31.03.2014 303 horn antenna 40 GHz (Subst 1) BBHA9170 156 Schwarzbeck 36 M - 31.03.2014 331 Climatic Test Chamber -40/+80 Grad HC 4055 43146 Heraeus Vötsch 24 M - 30.11.2012 341 Digital Multimeter Fluke 112 81650455 Fluke 24 M - 31.03.2014 342 Digital Multimeter Voltcraft M-4660A IB 255466 Voltcraft 24 M - 31.03.2014 347 laboratory site radio lab. - - - 5 348 laboratory site EMI conducted - - - 5 354 DC - Power Supply 40A NGPE 40/40 448 Rohde & Schwarz pre-m 2 355 Power Meter URV 5 891310/027 Rohde & Schwarz 24 M - 31.03.2014 356 power sensor NRV-Z1 882322/014 Rohde & Schwarz 24 M - 31.03.2014 357 power sensor NRV-Z1 861761/002 Rohde & Schwarz 24 M - 31.03.2014 371 Bluetooth Tester CBT32 100153 R&S 12 M - 31.03.2014 373 Single-Line V-Network (50 Ohm/5µH) ESH3-Z6 100535 Rohde & Schwarz 24/12 M - 31.03.2014 376 Horn Antenna 6 GHz BBHA9120 E BBHA 9120 E 179 Schwarzbeck 12 M - 31.03.2014 377 EMI Test Receiver ESCS 30 100160 Rohde & Schwarz 12 M - 31.03.2014 389 Digital Multimeter Keithley 2000 0583926 Keithley 24 M - 31.03.2014 392 Radio Communication Tester MT8820A 6K00000788 Anritsu 12 M - 31.03.2014 431 Model 7405 Near-Field Probe Set 9305-2457 EMCO - 4 436 Univ. Radio Communication Tester CMU 200 103083 Rohde & Schwarz 12 M - 31.03.2014 System EMI field (SAR) 441 CTC-SAR-EMI Cable Loss - CETECOM 12 M 5 31.10.2014 Cable System CTC-FAR-EMI- ETS-Lindgren / 443 CTC-FAR-EMI-RSE - 12 M 5 30.06.2014 RSE CETECOM WRCT 1850.0/2170.0- Wainwright Instruments 448 notch filter WCDMA_FDD II 5 12 M 1c 30.06.2014 5/40- GmbH WRCT 824.0/894.0-5/40- 449 notch filter WCDMA FDD V 1 Wainwright 12 M 1c 30.06.2014 8SSK 454 Oscilloscope HM 205-3 9210 P 29661 Hameg - 4 456 DC-Power supply 0-5 A EA 3013 S 207810 Elektro Automatik pre-m 2 459 DC -Power supply 0-5 A , 0-32 V EA-PS 2032-50 910722 Elektro Automatik pre-m 2 460 Univ. Radio Communication Tester CMU 200 108901 Rohde & Schwarz 12 M - 31.03.2014 463 Universal source HP3245A 2831A03472 Agilent - 4 466 Digital Multimeter Fluke 112 89210157 Fluke USA 24 M - 31.03.2014 467 Digital Multimeter Fluke 112 89680306 Fluke USA 24 M - 31.03.2014 468 Digital Multimeter Fluke 112 90090455 Fluke USA 24 M - 31.03.2014 477 ReRadiating GPS-System AS-47 - Automotive Cons. Fink - 3 480 power meter (Fula) NRVS 838392/031 Rohde & Schwarz 24 M - 31.03.2014 482 filter matrix Filter matrix SAR 1 - CETECOM (Brl) - 1d AMF-5D-02501800-25- 484 pre-amplifier 2,5 - 18 GHz 1244554 Miteq 12 M - 30.06.2014 10P System EMI field (SAR) ETS Lindgren / 487 System CTC NSA-Verification SAR-EMI - 24 M - 30.09.2014 NSA CETECOM 489 EMI Test Receiver ESU40 1000-30 Rohde & Schwarz 12 M - 31.03.2014 WRCG 1709/1786- 502 band reject filter SN 9 Wainwright pre-m 2 1699/1796- 503 band reject filter WRCG 824/849-814/859- SN 5 Wainwright pre-m 2 WRCA 800/960-02/40- 512 notch filter GSM 850 SN 24 Wainwrght 12 M 1c 30.06.2014 6EEK 517 relais switch matrix HF Relais Box Keithley SE 04 Keithley pre-m 2 523 Digital Multimeter L4411A MY46000154 Agilent 24 M - 31.03.2014 529 6 dB Broadband resistive power divider Model 1515 LH 855 Weinschel pre-m 2 530 10 dB Broadband resistive power divider R 416110000 LOT 9828 - pre-m 2 546 Univ. Radio Communication Tester CMU 200 106436 R&S 12 M - 31.03.2014 547 Univ. Radio Communication Tester CMU 200 835390/014 Rohde & Schwarz 12 M - 31.03.2014 548 Digital-Barometer GBP 2300 without Greisinger GmbH 36 M - 30.06.2015 549 Log.Per-Antenna HL025 1000060 Rohde & Schwarz 36/12 M - 31.03.2015 552 high pass filter 2,8-18GHz WHKX 2.8/18G-10SS 4 Wainwright 12 M 1c 30.06.2014 System CTC FAR S- 558 System CTC FAR S-VSWR - CTC 24 M - 31.07.2014 VSWR 574 Biconilog Hybrid Antenna BTA-L 980026L Frankonia 36/12 M - 30.03.2014 584 Spectrum Analyzer FSU 8 100248 Rohde & Schwarz 12 M - 31.03.2014 594 Wideband Radio Communication Tester CMW500 101757 Rohde & Schwarz 24 M - 31.03.2014 597 Univ. Radio Communication Tester CMU 200 100347 Rohde & Schwarz 12 M - 31.03.2014 598 Spectrum Analyzer FSEM 30 (Reserve) 831259/013 Rohde & Schwarz 24 M - 13.01.2014 600 power meter NRVD (Reserve) 834501/018 Rohde & Schwarz 24 M - 31.03.2014 601 medium-sensitivity diode sensor NRV-Z5 (Reserve) 8435323/003 Rohde & Schwarz 24 M - 12.01.2014 602 peak power sensor NRV-Z32 (Reserve) 835080 Rohde & Schwarz 24 M - 12.01.2014 608 UltraLog-Antenna HL 562 830547/009 Rohde & Schwarz 36/12 M - 31.03.2014 611 DC power supply E3632A KR 75305854 Agilent pre-m 2 612 DC power supply E3632A MY 40001321 Agilent pre-m 2 613 Attenuator R416120000 20dB 10W Lot. 9828 Radiall pre-m 2 616 Digitalmultimeter Fluke 177 88900339 Fluke 24 M - 31.03.2014 617 Power Splitter/Combiner ZFSC-2-2-S+ S F987001108 Mini Circuits - 2 TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 30 of 31 Ref.-No. calibration Interval of Remark Equipment Type Serial-No. Manufacturer Cal due 618 Power Splitter/Combiner 50PD-634 600994 JFW Industries USA - 2 619 Power Splitter/Combiner 50PD-634 600995 JFW Industries, USA - 3 620 EMI Test Receiver ESU 26 100362 Rohde-Schwarz 12 M - 01.01.2014 621 Step Attenuator 0-139 dB RSP 100017 Rohde & Schwarz pre-m 2 625 Generic Test Load USB Generic Test Load USB - CETECOM - 2 201.0999.9302.6.4.1.4 627 data logger OPUS 1 G. Lufft GmbH 24 M - 30.05.2014 3 634 Spectrum Analyzer FSM (HF-Unit) 826188/010 Rohde & Schwarz pre-m 2 635 DFS Testbox DFS Testbox 2012 V01 CETECOM SHA - - 636 Wärmebildkamera Ti32 Ti32-12060213, Tele Fluke Corporation 24 M - 31.07.2014 HDMI cable with Ethernet 637 High Speed HDMI with Ethernet 1m - KogiLink - 2 1m 638 HDMI Kabel with Ethernet 1,5 m flach HDMI cable with Ethernet - Reichelt - 2 640 HDMI cable 2m rund HDMI cable 2m rund - Reichelt - 2 641 HDMI cable with Ethernet Certified HDMI cable with - PureLink - 2 642 Wideband Radio Communication Tester CMW 500 126089 Rohde&Schwarz 24 M - 31.03.2014 TR6-0330-13-3-6a

Test Report 6-0330-13-3-6a, Page 31 of 31 8.1.3. Legend Note / remarks Calibrated during system calibration: 1a System CTC-SAR-EMS (Ref.-No. 442) 1b System-CTC-EMS-Conducted (Ref.-No. 335) 1c System CTC-FAR-EMI-RSE (Ref.-No . 443) 1d System CTC-SAR-EMI (Ref.-No . 441) 1e System CTC-OATS (EMI radiated) (Ref.-No. 337) 1f System CTC-CTIA-OTA (Ref.-No . 420) 1g System CTC-FAR-EMS (Ref.-No . 444) 2 Calibration or equipment check immediately before measurement 3 Regulatory maintained equipment for functional check or support purpose 4 calibration of this equipment Ancillary equipment without has no effect calibration onmechanical e.g. measuring result equipment or monitoring equipment 5 Test System Interval of calibration 12 M 12 month 24 M 24 month 36 M 36 month 24/12 M Calibration every 24 months, between this every 12 months internal validation 36/12 M Calibration every 36 months, between this every 12 months internal validation Pre-m Check before starting the measurement - Without calibration TR6-0330-13-3-6a


Document Created: 2013-11-08 15:23:47
Document Modified: 2013-11-08 15:23:47
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC