MDE_UBLOX_1828_FCCf_SIGNED

FCC ID: XPYJODYW167

Test Report

Download: PDF
FCCID_4346845

FCC Measurement/Technical Report on WLAN and Bluetooth module JODY-W167-03A Simultaneous Transmissions FCC ID: XPYJODYW167 IC: 8595A-JODYW167 Test Report Reference: MDE_UBLOX_1828_FCCf Test Laboratory: 7layers GmbH Borsigstrasse 11 40880 Ratingen Germany Note: The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts without the written approval of the test laboratory. 7layers GmbH Geschäftsführer/ Borsigstraße 11 Managing Directors: Registergericht/registered: a Bureau Veritas 40880 Ratingen, Germany Frank Spiller Düsseldorf HRB 75554 Group Company T +49 (0) 2102 749 0 Bernhard Retka USt-Id.-Nr./VAT-No. DE203159652 F +49 (0) 2102 749 350 Alexandre Norré-Oudard Steuer-Nr./TAX-No. 147/5869/0385 www.7layers.com Commerzbank AG Account No. 303 016 000 Bank Code 300 400 00 IBAN DE81 3004 0000 0303 0160 00 Swift Code COBADEFF

Table of Contents 1 Applied Standards and Test Summary 3 1.1 Applied Standards 3 1.2 FCC-IC Correlation Table 4 1.3 Measurement Summary / Signatures 5 2 Revision History 6 3 Administrative Data 7 3.1 Testing Laboratory 7 3.2 Project Data 7 3.3 Applicant Data 7 3.4 Manufacturer Data 8 4 Test object Data 9 4.1 General EUT Description 9 4.2 EUT Main components 10 4.3 Ancillary Equipment 10 4.4 Auxiliary Equipment 10 4.5 EUT Setups 10 4.6 Operating Modes 11 4.7 Product labelling 11 5 Test Results 12 5.1 Undesirable Emissions; General Field Strength Limits 12 6 Test Equipment 17 7 Antenna Factors, Cable Loss and Sample Calculations 20 7.1 LISN R&S ESH3-Z5 (150 kHz – 30 MHz) 20 7.2 Antenna R&S HFH2-Z2 (9 kHz – 30 MHz) 21 7.3 Antenna R&S HL562 (30 MHz – 1 GHz) 22 7.4 Antenna R&S HF907 (1 GHz – 18 GHz) 23 7.5 Antenna EMCO 3160-09 (18 GHz – 26.5 GHz) 24 7.6 Antenna EMCO 3160-10 (26.5 GHz – 40 GHz) 25 8 Setup Drawings 26 9 Measurement Uncertainties 27 10 Photo Report 27 TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCf Page 2 of 27

1 APPLIED STANDARDS AND TEST SUMMARY 1.1 APPLIED STANDARDS Type of Authorization Certification for an Intentional Radiator (Digital Device / Spread Spectrum). Applicable FCC Rules Prepared in accordance with the requirements of FCC Rules and Regulations as listed in 47 CFR Ch.1 Parts 2 (10-1-17 Edition) and 15 (10-1-17 Edition). The following subparts are applicable to the results in this test report. Part 2, Subpart J - Equipment Authorization Procedures, Certification Part 15, Subpart C – Intentional Radiators § 15.201 Equipment authorization requirement § 15.207 Conducted limits § 15.209 Radiated emission limits; general requirements § 15.247 Operation within the bands 902-928 MHz, 2400-2483.5 MHz § 15.407 General technical requirements Note: ANSI C63.10-2013 is applied. TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCf Page 3 of 27

Summary Test Results: The EUT complied with all performed tests as listed in chapter 1.3 Measurement Summary / Signatures. 1.2 FCC-IC CORRELATION TABLE Correlation of measurement requirements for DTS (e.g. WLAN 2.4 GHz, BT LE) equipment from FCC and IC DTS equipment Measurement FCC reference IC reference Transmitter spurious § 15.247 (d); RSS-Gen Issue 5: 6.13 / radiated emissions § 15.209 (a) 8.9/8.10; RSS-247 Issue 2: 5.5 Correlation of measurement requirements for UNII / LE-LAN (e.g. WLAN 5 GHz) equipment from FCC and IC UNII equipment Measurement FCC reference IC reference Transmitter undesirable § 15.407 (b) RSS-Gen Issue 5: emissions; § 15.209 (a) 6.13/8.9/8.10; General Field Strength RSS-247 Issue 2: 3.3/6.2 Limits, 6.2.1.2, 6.2.2.2, 6.2.3.2, Restricted Bands 6.2.4.2 TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCf Page 4 of 27

1.3 MEASUREMENT SUMMARY / SIGNATURES 47 CFR CHAPTER I FCC PART 15 Subpart E FCC §15.407 (b), §15.407 (1),(2),(3),(4); FCC §15.205, §15.209, §15.407 (b) (5),(6) Undesirable Emissions; General Field Strength Limits The measurement was performed according to ANSI C63.10 Final Result OP-Mode Setup FCC IC Radio Technology, Operating Frequency, Method of measurement 2.4 GHz Band: Bluetooth, Hopping, radiated S01_7_AC02 Passed Passed 2.4 GHz Band: WLAN mode n 20 MHz, 2441 MHz, radiated 5 GHz Band: WLAN mode ac 80 MHz, 5210 MHz, radiated 2.4 GHz Band: Bluetooth, Hopping, conducted S01_7_AC02 Passed Passed 2.4 GHz Band: WLAN mode n 20 MHz, 2441 MHz, conducted 5 GHz Band: WLAN mode ac 80 MHz, 5210 MHz, conducted N/A: Not applicable N/P: Not performed TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCf Page 5 of 27

+layers A Bureau Veritas Group Company 2 REVISION HISTORY Report version control Version Release date Change Description Version validity initial 2019—05—28 ~~ valid COMMENT: — M. Jt (responsible for accreditation scope) PA/b (responsible for testing and report) Dipl.—Ing. Marco Kullik Dipl.—Ing. Daniel Gall #layers nay 7 layers GmbH, Borsigstr. 11 40880 Ratingen, Germany Phone +498 (0)2102 749 0 TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCF Page 6 of 27

3 ADMINISTRATIVE DATA 3.1 TESTING LABORATORY Company Name: 7layers GmbH Address: Borsigstr. 11 40880 Ratingen Germany The test facility is accredited by the following accreditation organisation: Laboratory accreditation no: DAkkS D-PL-12140-01-00 FCC Designation Number: DE0015 FCC Test Firm Registration: 929146 ISED CAB Identifier DE0007; ISED#: 3699A Responsible for accreditation scope: Dipl.-Ing. Marco Kullik Report Template Version: 2019-02-12 3.2 PROJECT DATA Responsible for testing and report: Dipl.-Ing. Daniel Gall Employees who performed the tests: documented internally at 7Layers Date of Report: 2019-05-28 Testing Period: 2019-05-23 to 2019-05-24 3.3 APPLICANT DATA Company Name: u-blox AG Address: Zürcherstrasse 68 8800 Thalwil Switzerland Contact Person: Filip Kruzela TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCf Page 7 of 27

3.4 MANUFACTURER DATA Company Name: u-blox AG Address: Zürcherstrasse 68 8800 Thalwil Switzerland Contact Person: Filip Kruzela TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCf Page 8 of 27

4 TEST OBJECT DATA 4.1 GENERAL EUT DESCRIPTION Kind of Device The EUT is a module supporting WLAN in the 2.4 GHz and 5 GHz product description bands as well as Bluetooth (BT) 4.2 including Bluetooth Low Energy (BT LE) Product name JODY-W167-03A Type JODY-W167-03A Declared EUT data by the supplier Voltage Type DC Voltage Level 3.3 V Specific product The JODY-W1 is a compact automotive grade module that provides description Wi-Fi, Bluetooth, and Bluetooth low energy communication. The JODY-W167-03A module can be operated in the following modes: Wi-Fi 2x2 MIMO 802.11n in the 2.4 GHz and 5 GHz bands. Wi-Fi 2x2 MIMO 802.11ac in the 5GHz band. Wi-Fi 802.11n/ac real simultaneous dual band on two antennas. Dual-mode Bluetoothv4.2, can be operated fully simultaneous with both the Wi-Fi modes. It is equipped with three antenna pins connected two three SMA connectors on the evaluation board. Maximum supported band width in 2.4 GHz Wi-Fi mode: 20 MHz, 5GHz Wi-Fi mode: 80 MHz Ports of the device DC Power Supply Antenna ports Signal ports Antenna 1 None provided, 2 dBi antenna gain assumed for conducted measurements Antenna 2 None provided, 2 dBi antenna gain assumed for conducted measurements Special software used The test modes were set using scripts that were run on a board for testing computer with linux operating system provided by the applicant. The main components of the EUT are listed and described in chapter 3.2 EUT Main components. TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCf Page 9 of 27

4.2 EUT MAIN COMPONENTS Sample Name Sample Code Description EUT ac02 DE1015104ac02 Sample Parameter Value Serial No. 946D4CA6ED288040700 HW Version 00 SW Version P8.1 Comment Integral Antenna None, three external 50 Ohm connectors on evaluation board. Antenna gain used for evaluation of test results: 2dBi NOTE:The short description is used to simplify the identification of the EUT in this test report. 4.3 ANCILLARY EQUIPMENT For the purposes of this test report, ancillary equipment is defined as equipment which is used in conjunction with the EUT to provide operational and control features to the EUT. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Ancillary Equipment can influence the test results. Device Details Description (Manufacturer, Type Model, OUT Code) Evaluation Board -, UBLOX JODY-W1 EVB Certivication Board providing ports to board, the EUT Sample Name Description Evaluation Board Evaluation Board 4.4 AUXILIARY EQUIPMENT For the purposes of this test report, auxiliary equipment is defined as equipment which is used temporarily to enable operational and control features especially used for the tests of the EUT which is not used during normal operation or equipment that is used during the tests in combination with the EUT but is not subject of this test report. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Auxiliary Equipment can influence the test results. Device Details Description (Manufacturer, Type Model, HW, SW, S/N) Board Computer Toradex, Ixora, -, - , - Computer used for setting the test modes 4.5 EUT SETUPS TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCf Page 10 of 27

This chapter describes the combination of EUTs and equipment used for testing. The rationale for selecting the EUTs, ancillary and auxiliary equipment and interconnecting cables, is to test a representative configuration meeting the requirements of the referenced standards. Setup Combination of EUTs Description and Rationale S01_7_AC02 EUT ac02, Evaluation Board, Board Computer Representative Setup 4.6 OPERATING MODES This chapter describes the operating modes of the EUTs used for testing. All technologies were set to normal mode allowing max. data throughput and a data throughput test was started. (BT EDR, WLAN 2.4 GHz mode n 20 MHz, WLAN 5 GHz mode ac 80 Mhz) 4.6.1 TEST CHANNELS Bluetooth: hopping WLAN 2.4 GHz: Ch. 7 @ 2441 MHz WLAN 5 GHz: Ch. 42 @ 5210 MHz 4.7 PRODUCT LABELLING 4.7.1 FCC ID LABEL Please refer to the documentation of the applicant. 4.7.2 LOCATION OF THE LABEL ON THE EUT Please refer to the documentation of the applicant. TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCf Page 11 of 27

5 TEST RESULTS 5.1 UNDESIRABLE EMISSIONS; GENERAL FIELD STRENGTH LIMITS Standard FCC Part 15 Subpart E / FCC Part 15 Subpart C The test was performed according to: ANSI C63.10 5.1.1 TEST DESCRIPTION The test set-up was made in accordance to the general provisions of ANSI C63.10 in a typical installation configuration. The Equipment Under Test (EUT) was set up on a non-conductive table 1.0 x 2.0 m² in the semi-anechoic chamber. The influence of the EUT support table that is used between 30–1000 MHz was evaluated. The measurement procedure is implemented into the EMI test software EMC32 from R&S. Exploratory tests are performed at 3 orthogonal axes to determine the worst-case orientation of a body-worn or handheld EUT. The final test on all kind of EUTs is also performed at 3 axes. A pre-check is performed while the EUT is powered from a DC power source. 3. Measurement above 1 GHz The following modifications apply to the measurement procedure for the frequency range above 1 GHz: Step 1: The Equipment Under Test (EUT) was set up on a non-conductive support (tilt device) at 1.5 m height in the fully-anechoic chamber. All steps were performed with one height (1.5 m) of the receiving antenna only. The EUT is turned during the preliminary measurement across the elevation axis, with a step size of 90 °. The turn table step size (azimuth angle) for the preliminary measurement is 45 °. Above 26 GHz the measurement distance is reduced to 1 m. Step 2: Due to the fact, that in this frequency range the test is performed in a fully anechoic room, the height scan of the receiving antenna instep 2 is omitted. Instead of this, a maximum search with a step size ± 45° for the elevation axis is performed. The turn table azimuth will slowly vary by ± 22.5°. The elevation angle will slowly vary by ± 45° EMI receiver settings (for all steps): - Detector: Peak, Average - IF Bandwidth = 1 MHz Step 3: Spectrum analyser settings for step 3: - Detector: Peak / Average - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 1 MHz - Measuring time: 1 s TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCf Page 12 of 27

5.1.2 TEST REQUIREMENTS / LIMITS FCC Part 15, Subpart C FCC Part 15, Subpart C, §15.247 (d) ... In addition, radiated emissions which fall in the restricted bands, as defined in Section 15.205(a), must also comply with the radiated emission limits specified in Section 15.209(a) (see Section 15.205(c)). FCC Part 15, Subpart C, §15.209, Radiated Emission Limits Measurement Frequency in MHz Limit (µV/m) Limits (dBµV/m) distance (m) 0.009 – 0.49 2400/F(kHz)@300m 3 (48.5 – 13.8)@300m 0.49 – 1.705 24000/F(kHz)@30m 3 (33.8 – 23.0)@30m 1.705 – 30 30@30m 3 29.5@30m The measured values are corrected with an inverse linear distance extrapolation factor (40 dB/decade) according FCC 15.31 (2). Measurement Frequency in MHz Limit (µV/m) Limits (dBµV/m) distance (m) 30 – 88 100@3m 3 40.0@3m 88 – 216 150@3m 3 43.5@3m 216 – 960 200@3m 3 46.0@3m 960 - 26000 500@3m 3 54.0@3m 26000 - 40000 500@3m 1 54.0@3m The measured values above 26 GHz are corrected with an inverse linear distance extrapolation factor (20 dB/decade). §15.35(b) ..., there is also a limit on the radio frequency emissions, as measured using instrumentation with a peak detector function, corresponding to 20 dB above the maximum permitted average limit.... Used conversion factor: Limit (dBµV/m) = 20 log (Limit (µV/m)/1µV/m) FCC Part 15, Subpart E A) FCC FCC Part 15 Subpart E, §15.407 (b)(1) For transmitters operating in the 5150–5250 MHz band: Limit: –27 dBm/MHz EIRP outside of the band 5150–5350 MHz. B) IC Different frequency bands and limits apply, as compared to the FCC requirements. RSS-247, 6.2.1 (2), Emissions outside the band 5150-5250 MHz, indoor operation only: Limit: –27 dBm/MHz EIRP outside of the band 5150–5250 MHz. C) FCC & IC TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCf Page 13 of 27

FCC Part 15 Subpart E, §15.405 The provisions of §§ 15.203 and 15.205 are included. §15.407 (b)(6) Unwanted emissions below 1 GHz must comply with the general field strength limits set forth in § 15.209. §15.407 (b)(7) The provisions of §15.205 apply to intentional radiators operating under this section FCC Part 15, Subpart C, §15.209, Radiated Emission Limits Measurement Frequency in MHz Limit (µV/m) Limits (dBµV/m) distance (m) 0.009 – 0.49 2400/F(kHz)@300m 3 (48.5 – 13.8)@300m 0.49 – 1.705 24000/F(kHz)@30m 3 (33.8 – 23.0)@30m 1.705 – 30 30@30m 3 29.5@30m The measured values are corrected with an inverse linear distance extrapolation factor (40 dB/decade) according FCC 15.31 (2). Measurement Frequency in MHz Limit (µV/m) Limits (dBµV/m) distance (m) 30 – 88 100@3m 3 40.0@3m 88 – 216 150@3m 3 43.5@3m 216 – 960 200@3m 3 46.0@3m 960 - 26000 500@3m 3 54.0@3m 26000 - 40000 500@3m 1 54.0@3m The measured values above 26 GHz are corrected with an inverse linear distance extrapolation factor (20 dB/decade). §15.35(b) ..., there is also a limit on the radio frequency emissions, as measured using instrumentation with a peak detector function, corresponding to 20 dB above the maximum permitted average limit.... Used conversion factor: • Limit (dBµV/m) = 20 log (Limit (µV/m)/1µV/m) • Limit (dBµV/m) = EIRP [dBm] – 20 log (d [m]) + 104.8 Limit types (in result tables on next page): RB – Emissions falls into a “Restricted Band” according FCC §§15.205 and 15.209 *) UE – “Undesirable Emission Limit” according FCC §15.407 BE-RB – Band Edge Limit basing on “Restricted Band Limits” BE-UE – Band Edge Limit basing on “Undesirable Emission Limit” *) Below 1 GHz the limits of §15.209 are applied for all frequencies. TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCf Page 14 of 27

5.1.3 TEST PROTOCOL Ambient temperature: 27 °C Air Pressure: 1019 hPa Humidity: 33 % Remark: Please see next sub-clause for the measurement plot. 5.1.4 MEASUREMENT PLOT (SHOWING THE HIGHEST VALUE, “WORST CASE”) Radiated Emissions Level in dBµV/m Critical_Freqs Frequency MaxPeak Average Limit Margi Meas. Bandwidt Heigh Pol Azimut Elevatio (MHz) (dBµV/m) (dBµV/m) (dBµV/m) n Time h t h n (dB) (ms) (kHz) (cm) (deg) (deg) 1247.650 61.1 --- 68.20 7.14 --- --- 150.0 V -144.0 95.0 1261.000 53.3 --- 68.20 14.92 --- --- 150.0 H 135.0 100.0 3749.600 57.0 --- 74.00 16.98 --- --- 150.0 H -36.0 0.0 3749.600 --- 30.1 54.00 23.93 --- --- 150.0 H -43.0 5.0 Final_Result Frequency MaxPeak CAverage Limit Margi Meas. Bandwidt Heigh Pol Azimut Elevatio (MHz) (dBµV/m) (dBµV/m) (dBµV/m) n Time h t h n (dB) (ms) (kHz) (cm) (deg) (deg) 1247.650 58.1 --- 68.20 10.10 1000.0 1000.000 150.0 V -144.0 95.0 1261.000 47.6 --- 68.20 20.60 1000.0 1000.000 150.0 H 135.0 100.0 3749.600 --- 31.4 54.00 22.63 1000.0 1000.000 150.0 H -43.0 5.0 3749.600 63.5 --- 74.00 10.46 1000.0 1000.000 150.0 H -36.0 0.0 Note: The emissions around 2440 and 5210 MHz are the intentional transmitters and not relevant to the limit. The antenna connectors were terminated with 50 Ohm resistors. TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCf Page 15 of 27

Conducted Emissions 20 15 10 5 0 -5 -10 -15 Level in dBm -20 -25 FCC_15.407_PEAK_SUB1&2A_dBm -30 -35 -40 FCC_15.407_AV_1GHz-40GHz_dBm -45 -50 -55 1G 2G 3G 4G 5G 6 8 10G 20G 26G Frequency in Hz Note: The emissions around 2440 and 5210 MHz are the intentional transmitters and not relevant to the limit. An additional 2 dB were are included in the trace to compensate for 2 dBi antenna gain. 5.1.5 TEST EQUIPMENT USED - Radiated Emissions TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCf Page 16 of 27

6 TEST EQUIPMENT 1 Radiated Emissions Lab to perform radiated emission tests Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 1.1 NRV-Z1 Sensor Head A Rohde & Schwarz 827753/005 2018-07 2019-07 GmbH & Co. KG 1.2 MFS Rubidium Datum GmbH 002 2018-10 2020-10 Frequency Normal MFS 1.3 Opus10 TPR ThermoAirpres Lufft Mess- und 13936 2017-04 2019-05 (8253.00) sure Regeltechnik GmbH Datalogger 13 (Environ) 1.4 ESW44 EMI Test Rohde & Schwarz 101603 Receiver GmbH & Co. KG 1.5 Anechoic 10.58 x 6.38 x Frankonia none 2018-06 2020-06 Chamber 6.00 m³ 1.6 FS-Z60 Harmonic Rohde & Schwarz 100178 2016-12 2019-12 Mixer 40 - 60 Messgerätebau GHz GmbH 1.7 FS-Z220 Harmonic Rohde & Schwarz 101005 2017-03 2020-03 Mixer 140 - Messgerätebau 220 GHz GmbH 1.8 SGH-05 Standard Gain RPG-Radiometer 075 / Pyramidal Physics GmbH Horn Antenna (140 - 220 GHz) 1.9 HL 562 Ultralog new Rohde & Schwarz 830547/003 2018-07 2021-07 biconicals 1.10 5HC2700/12750 High Pass Trilithic 9942012 -1.5-KK Filter 1.11 ASP 1.2/1.8-10 Antenna Mast Maturo GmbH - kg 1.12 Fully Anechoic 8.80m x Albatross Projects P26971-647-001- 2018-06 2020-06 Room 4.60m x PRB 4.05m (l x w x h) 1.13 Fluke 177 Digital Fluke Europe B.V. 86670383 2018-04 2020-04 Multimeter 03 (Multimeter) 1.14 NRVD Power Meter Rohde & Schwarz 828110/016 2018-07 2019-07 GmbH & Co. KG 1.15 HF 906 Double-ridged Rohde & Schwarz 357357/002 2018-09 2021-09 horn 1.16 JS4-18002600- Broadband Miteq 849785 32-5P Amplifier 18 GHz - 26 GHz 1.17 FSW 43 Spectrum Rohde & Schwarz 103779 2019-02 2021-02 Analyzer 1.18 3160-09 Standard Gain EMCO Elektronic 00083069 / Pyramidal GmbH Horn Antenna 26.5 GHz TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCf Page 17 of 27

Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 1.19 SGH-19 Standard Gain RPG-Radiometer 093 / Pyramidal Physics GmbH Horn Antenna (40 - 60 GHz) 1.20 WHKX 7.0/18G- High Pass Wainwright 09 8SS Filter 1.21 4HC1600/12750 High Pass Trilithic 9942011 -1.5-KK Filter 1.22 Chroma 6404 AC Power Chroma ATE INC. 64040001304 Source 1.23 JS4-00102600- Broadband Miteq 619368 42-5A Amplifier 30 MHz - 26 GHz 1.24 TT 1.5 WI Turn Table Maturo GmbH - 1.25 HL 562 Ultralog Log.-per. Rohde & Schwarz 100609 2019-05 2022-05 Antenna 1.26 HF 906 Double-ridged Rohde & Schwarz 357357/001 2018-03 2021-03 horn 1.27 FS-Z325 Harmonic Rohde & Schwarz 101006 2017-03 2020-03 Mixer 220 - Messgerätebau 325 GHz GmbH 1.28 3160-10 Standard Gain EMCO Elektronic 00086675 / Pyramidal GmbH Horn Antenna 40 GHz 1.29 SGH-08 Standard Gain RPG-Radiometer 064 / Pyramidal Physics GmbH Horn Antenna (90 - 140 GHz) 1.30 SGH-12 Standard Gain RPG-Radiometer 326 / Pyramidal Physics GmbH HornAntenna (60 - 90 GHz) 1.31 5HC3500/18000 High Pass Trilithic 200035008 -1.2-KK Filter 1.32 FS-Z140 Harmonic Rohde & Schwarz 101007 2017-02 2020-02 Mixer 90 -140 Messgerätebau GHz GmbH 1.33 HFH2-Z2 Loop Antenna Rohde & Schwarz 829324/006 2018-01 2021-01 1.34 Opus10 THI ThermoHygro Lufft Mess- und 12482 2017-03 2019-05 (8152.00) Datalogger 12 Regeltechnik GmbH (Environ) 1.35 ESR 7 EMI Receiver / Rohde & Schwarz 101424 2019-01 2020-01 Spectrum Analyzer 1.36 JS4-00101800- Broadband Miteq 896037 35-5P Amplifier 30 MHz - 18 GHz 1.37 AS 620 P Antenna mast HD GmbH 620/37 1.38 Tilt device Antrieb TD1.5- Maturo GmbH TD1.5- Maturo 10kg 10kg/024/37907 (Rohacell) 09 1.39 SGH-03 Standard Gain RPG-Radiometer 060 / Pyramidal Physics GmbH Horn Antenna (220 - 325 GHz) TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCf Page 18 of 27

Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 1.40 FS-Z90 Harmonic Rohde & Schwarz 101686 2017-03 2020-03 Mixer 60 - 90 Messgerätebau GHz GmbH 1.41 ESIB 26 Spectrum Rohde & Schwarz 830482/004 2018-01 2020-01 Analyzer 1.42 PAS 2.5 - 10 kg Antenna Mast Maturo GmbH - 1.43 AFS42- Broadband Miteq 2035324 00101800-25-S- Amplifier 25 42 MHz - 18 GHz 1.44 AM 4.0 Antenna mast Maturo GmbH AM4.0/180/1192 0513 1.45 HF 907 Double-ridged Rohde & Schwarz 102444 2018-07 2021-07 horn The calibration interval is the time interval between “Last Calibration” and “Calibration Due” TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCf Page 19 of 27

7 ANTENNA FACTORS, CABLE LOSS AND SAMPLE CALCULATIONS This chapter contains the antenna factors with their corresponding path loss of the used measurement path for all antennas as well as the insertion loss of the LISN. 7.1 LISN R&S ESH3-Z5 (150 KHZ – 30 MHZ) cable LISN loss insertion (incl. 10 loss dB ESH3- atten- Frequency Corr. Z5 uator) MHz dB dB dB 0.15 10.1 0.1 10.0 5 10.3 0.1 10.2 7 10.5 0.2 10.3 10 10.5 0.2 10.3 12 10.7 0.3 10.4 14 10.7 0.3 10.4 16 10.8 0.4 10.4 18 10.9 0.4 10.5 20 10.9 0.4 10.5 22 11.1 0.5 10.6 24 11.1 0.5 10.6 26 11.2 0.5 10.7 28 11.2 0.5 10.7 30 11.3 0.5 10.8 Sample calculation ULISN (dB µV) = U (dB µV) + Corr. (dB) U = Receiver reading LISN Insertion loss = Voltage Division Factor of LISN Corr. = sum of single correction factors of used LISN, cables, switch units (if used) Linear interpolation will be used for frequencies in between the values in the table. TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCf Page 20 of 27

7.2 ANTENNA R&S HFH2-Z2 (9 KHZ – 30 MHZ) cable cable cable cable distance dLimit dused loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. AF (inside (outside (switch (to (-40 dB/ distance distance Frequency HFH-Z2) Corr. chamber) chamber) unit) receiver) decade) (limit) (used) MHz dB (1/m) dB dB dB dB dB dB m m 0.009 20.50 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.01 20.45 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.015 20.37 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.02 20.36 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.025 20.38 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.03 20.32 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.05 20.35 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.08 20.30 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.1 20.20 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.2 20.17 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.3 20.14 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.49 20.12 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.490001 20.12 -39.6 0.1 0.1 0.1 0.1 -40 30 3 0.5 20.11 -39.6 0.1 0.1 0.1 0.1 -40 30 3 0.8 20.10 -39.6 0.1 0.1 0.1 0.1 -40 30 3 1 20.09 -39.6 0.1 0.1 0.1 0.1 -40 30 3 2 20.08 -39.6 0.1 0.1 0.1 0.1 -40 30 3 3 20.06 -39.6 0.1 0.1 0.1 0.1 -40 30 3 4 20.05 -39.5 0.2 0.1 0.1 0.1 -40 30 3 5 20.05 -39.5 0.2 0.1 0.1 0.1 -40 30 3 6 20.02 -39.5 0.2 0.1 0.1 0.1 -40 30 3 8 19.95 -39.5 0.2 0.1 0.1 0.1 -40 30 3 10 19.83 -39.4 0.2 0.1 0.2 0.1 -40 30 3 12 19.71 -39.4 0.2 0.1 0.2 0.1 -40 30 3 14 19.54 -39.4 0.2 0.1 0.2 0.1 -40 30 3 16 19.53 -39.3 0.3 0.1 0.2 0.1 -40 30 3 18 19.50 -39.3 0.3 0.1 0.2 0.1 -40 30 3 20 19.57 -39.3 0.3 0.1 0.2 0.1 -40 30 3 22 19.61 -39.3 0.3 0.1 0.2 0.1 -40 30 3 24 19.61 -39.3 0.3 0.1 0.2 0.1 -40 30 3 26 19.54 -39.3 0.3 0.1 0.2 0.1 -40 30 3 28 19.46 -39.2 0.3 0.1 0.3 0.1 -40 30 3 30 19.73 -39.1 0.4 0.1 0.3 0.1 -40 30 3 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) distance correction = -40 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCf Page 21 of 27

7.3 ANTENNA R&S HL562 (30 MHZ – 1 GHZ) (dLimit = 3 m) cable cable cable cable distance dLimit dused AF loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. R&S (inside (outside (switch (to (-20 dB/ distance distance Frequency HL562 Corr. chamber) chamber) unit) receiver) decade) (limit) (used) MHz dB (1/m) dB dB dB dB dB dB m m 30 18.6 0.6 0.29 0.04 0.23 0.02 0.0 3 3 50 6.0 0.9 0.39 0.09 0.32 0.08 0.0 3 3 100 9.7 1.2 0.56 0.14 0.47 0.08 0.0 3 3 150 7.9 1.6 0.73 0.20 0.59 0.12 0.0 3 3 200 7.6 1.9 0.84 0.21 0.70 0.11 0.0 3 3 250 9.5 2.1 0.98 0.24 0.80 0.13 0.0 3 3 300 11.0 2.3 1.04 0.26 0.89 0.15 0.0 3 3 350 12.4 2.6 1.18 0.31 0.96 0.13 0.0 3 3 400 13.6 2.9 1.28 0.35 1.03 0.19 0.0 3 3 450 14.7 3.1 1.39 0.38 1.11 0.22 0.0 3 3 500 15.6 3.2 1.44 0.39 1.20 0.19 0.0 3 3 550 16.3 3.5 1.55 0.46 1.24 0.23 0.0 3 3 600 17.2 3.5 1.59 0.43 1.29 0.23 0.0 3 3 650 18.1 3.6 1.67 0.34 1.35 0.22 0.0 3 3 700 18.5 3.6 1.67 0.42 1.41 0.15 0.0 3 3 750 19.1 4.1 1.87 0.54 1.46 0.25 0.0 3 3 800 19.6 4.1 1.90 0.46 1.51 0.25 0.0 3 3 850 20.1 4.4 1.99 0.60 1.56 0.27 0.0 3 3 900 20.8 4.7 2.14 0.60 1.63 0.29 0.0 3 3 950 21.1 4.8 2.22 0.60 1.66 0.33 0.0 3 3 1000 21.6 4.9 2.23 0.61 1.71 0.30 0.0 3 3 (dLimit = 10 m) 30 18.6 -9.9 0.29 0.04 0.23 0.02 -10.5 10 3 50 6.0 -9.6 0.39 0.09 0.32 0.08 -10.5 10 3 100 9.7 -9.2 0.56 0.14 0.47 0.08 -10.5 10 3 150 7.9 -8.8 0.73 0.20 0.59 0.12 -10.5 10 3 200 7.6 -8.6 0.84 0.21 0.70 0.11 -10.5 10 3 250 9.5 -8.3 0.98 0.24 0.80 0.13 -10.5 10 3 300 11.0 -8.1 1.04 0.26 0.89 0.15 -10.5 10 3 350 12.4 -7.9 1.18 0.31 0.96 0.13 -10.5 10 3 400 13.6 -7.6 1.28 0.35 1.03 0.19 -10.5 10 3 450 14.7 -7.4 1.39 0.38 1.11 0.22 -10.5 10 3 500 15.6 -7.2 1.44 0.39 1.20 0.19 -10.5 10 3 550 16.3 -7.0 1.55 0.46 1.24 0.23 -10.5 10 3 600 17.2 -6.9 1.59 0.43 1.29 0.23 -10.5 10 3 650 18.1 -6.9 1.67 0.34 1.35 0.22 -10.5 10 3 700 18.5 -6.8 1.67 0.42 1.41 0.15 -10.5 10 3 750 19.1 -6.3 1.87 0.54 1.46 0.25 -10.5 10 3 800 19.6 -6.3 1.90 0.46 1.51 0.25 -10.5 10 3 850 20.1 -6.0 1.99 0.60 1.56 0.27 -10.5 10 3 900 20.8 -5.8 2.14 0.60 1.63 0.29 -10.5 10 3 950 21.1 -5.6 2.22 0.60 1.66 0.33 -10.5 10 3 1000 21.6 -5.6 2.23 0.61 1.71 0.30 -10.5 10 3 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) distance correction = -20 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Tables show an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCf Page 22 of 27

7.4 ANTENNA R&S HF907 (1 GHZ – 18 GHZ) cable cable loss 3 loss 1 (switch (relay + cable unit, AF cable loss 2 atten- cable R&S inside (outside uator & loss 4 (to Frequency HF907 Corr. chamber) chamber) pre-amp) receiver) MHz dB (1/m) dB dB dB dB dB 1000 24.4 -19.4 0.99 0.31 -21.51 0.79 2000 28.5 -17.4 1.44 0.44 -20.63 1.38 3000 31.0 -16.1 1.87 0.53 -19.85 1.33 4000 33.1 -14.7 2.41 0.67 -19.13 1.31 5000 34.4 -13.7 2.78 0.86 -18.71 1.40 6000 34.7 -12.7 2.74 0.90 -17.83 1.47 7000 35.6 -11.0 2.82 0.86 -16.19 1.46 cable loss 4 cable (switch loss 1 cable cable unit, used AF (relay loss 2 loss 3 atten- cable for R&S inside (inside (outside uator & loss 5 (to FCC Frequency HF907 Corr. chamber) chamber) chamber) pre-amp) receiver) 15.247 MHz dB (1/m) dB dB dB dB dB dB 3000 31.0 -23.4 0.47 1.87 0.53 -27.58 1.33 4000 33.1 -23.3 0.56 2.41 0.67 -28.23 1.31 5000 34.4 -21.7 0.61 2.78 0.86 -27.35 1.40 6000 34.7 -21.2 0.58 2.74 0.90 -26.89 1.47 7000 35.6 -19.8 0.66 2.82 0.86 -25.58 1.46 cable loss 1 cable cable cable cable cable AF (relay loss 2 loss 3 loss 4 loss 5 loss 6 R&S inside (High (pre- (inside (outside (to Frequency HF907 Corr. chamber) Pass) amp) chamber) chamber) receiver) MHz dB (1/m) dB dB dB dB dB dB dB 7000 35.6 -57.3 0.56 1.28 -62.72 2.66 0.94 1.46 8000 36.3 -56.3 0.69 0.71 -61.49 2.84 1.00 1.53 9000 37.1 -55.3 0.68 0.65 -60.80 3.06 1.09 1.60 10000 37.5 -56.2 0.70 0.54 -61.91 3.28 1.20 1.67 11000 37.5 -55.3 0.80 0.61 -61.40 3.43 1.27 1.70 12000 37.6 -53.7 0.84 0.42 -59.70 3.53 1.26 1.73 13000 38.2 -53.5 0.83 0.44 -59.81 3.75 1.32 1.83 14000 39.9 -56.3 0.91 0.53 -63.03 3.91 1.40 1.77 15000 40.9 -54.1 0.98 0.54 -61.05 4.02 1.44 1.83 16000 41.3 -54.1 1.23 0.49 -61.51 4.17 1.51 1.85 17000 42.8 -54.4 1.36 0.76 -62.36 4.34 1.53 2.00 18000 44.2 -54.7 1.70 0.53 -62.88 4.41 1.55 1.91 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. Tables show an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCf Page 23 of 27

7.5 ANTENNA EMCO 3160-09 (18 GHZ – 26.5 GHZ) cable cable cable cable cable AF loss 1 loss 2 loss 3 loss 4 loss 5 EMCO (inside (pre- (inside (switch (to Frequency 3160-09 Corr. chamber) amp) chamber) unit) receiver) MHz dB (1/m) dB dB dB dB dB dB 18000 40.2 -23.5 0.72 -35.85 6.20 2.81 2.65 18500 40.2 -23.2 0.69 -35.71 6.46 2.76 2.59 19000 40.2 -22.0 0.76 -35.44 6.69 3.15 2.79 19500 40.3 -21.3 0.74 -35.07 7.04 3.11 2.91 20000 40.3 -20.3 0.72 -34.49 7.30 3.07 3.05 20500 40.3 -19.9 0.78 -34.46 7.48 3.12 3.15 21000 40.3 -19.1 0.87 -34.07 7.61 3.20 3.33 21500 40.3 -19.1 0.90 -33.96 7.47 3.28 3.19 22000 40.3 -18.7 0.89 -33.57 7.34 3.35 3.28 22500 40.4 -19.0 0.87 -33.66 7.06 3.75 2.94 23000 40.4 -19.5 0.88 -33.75 6.92 3.77 2.70 23500 40.4 -19.3 0.90 -33.35 6.99 3.52 2.66 24000 40.4 -19.8 0.88 -33.99 6.88 3.88 2.58 24500 40.4 -19.5 0.91 -33.89 7.01 3.93 2.51 25000 40.4 -19.3 0.88 -33.00 6.72 3.96 2.14 25500 40.5 -20.4 0.89 -34.07 6.90 3.66 2.22 26000 40.5 -21.3 0.86 -35.11 7.02 3.69 2.28 26500 40.5 -21.1 0.90 -35.20 7.15 3.91 2.36 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCf Page 24 of 27

7.6 ANTENNA EMCO 3160-10 (26.5 GHZ – 40 GHZ) cable cable cable cable distance dLimit dused AF loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. EMCO (inside (outside (switch (to (-20 dB/ distance distance Frequency 3160-10 Corr. chamber) chamber) unit) receiver) decade) (limit) (used) GHz dB (1/m) dB dB dB dB dB dB m m 26.5 43.4 -11.2 4.4 -9.5 3 1.0 27.0 43.4 -11.2 4.4 -9.5 3 1.0 28.0 43.4 -11.1 4.5 -9.5 3 1.0 29.0 43.5 -11.0 4.6 -9.5 3 1.0 30.0 43.5 -10.9 4.7 -9.5 3 1.0 31.0 43.5 -10.8 4.7 -9.5 3 1.0 32.0 43.5 -10.7 4.8 -9.5 3 1.0 33.0 43.6 -10.7 4.9 -9.5 3 1.0 34.0 43.6 -10.6 5.0 -9.5 3 1.0 35.0 43.6 -10.5 5.1 -9.5 3 1.0 36.0 43.6 -10.4 5.1 -9.5 3 1.0 37.0 43.7 -10.3 5.2 -9.5 3 1.0 38.0 43.7 -10.2 5.3 -9.5 3 1.0 39.0 43.7 -10.2 5.4 -9.5 3 1.0 40.0 43.8 -10.1 5.5 -9.5 3 1.0 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. distance correction = -20 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCf Page 25 of 27

8 SETUP DRAWINGS Drawing 1: Setup in the Anechoic chamber. For measurements below 1 GHz the ground was replaced by a conducting groundplane. Shielded Shielded RF cable RF cable OUT Rubidium Spectrum (object Frequency 4 to 1 Analyser under test) Standard coupler Companion 4 to 1 device 10 dB att. coupler 50 Ohm Drawing 2: Setup for conducted radio tests. TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCf Page 26 of 27

9 MEASUREMENT UNCERTAINTIES Test Case Parameter Uncertainty AC Power Line Power ± 3.4 dB Field Strength of spurious radiation Power ± 5.5 dB 6 dB / 26 dB / 99% Bandwidth Power ± 2.9 dB Frequency ± 11.2 kHz Conducted Output Power Power ± 2.2 dB Band Edge Compliance Power ± 2.2 dB Frequency ± 11.2 kHz Frequency Stability Frequency ± 25 Hz Power Spectral Density Power ± 2.2 dB 10 PHOTO REPORT Please see separate photo report. TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCf Page 27 of 27


Document Created: 2019-07-08 13:34:09
Document Modified: 2019-07-08 13:34:09
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC