Test Report

FCC ID: XPYJODYW164

Test Report

Download: PDF
FCCID_4206799

FCC Measurement/Technical Report on WLAN and Bluetooth module JODY-W163-13A FCC ID: XPYJODYW164 IC: 8595A-JODYW164 Test Report Reference: MDE_UBLOX_1828_FCCc Test Laboratory: 7layers GmbH Borsigstrasse 11 40880 Ratingen Germany Note: The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts without the written approval of the test laboratory. 7layers GmbH Geschäftsführer/ Borsigstraße 11 Managing Directors: Registergericht/registered: a Bureau Veritas 40880 Ratingen, Germany Frank Spiller Düsseldorf HRB 75554 Group Company T +49 (0) 2102 749 0 Bernhard Retka USt-Id.-Nr./VAT-No. DE203159652 F +49 (0) 2102 749 350 Alexandre Norré-Oudard Steuer-Nr./TAX-No. 147/5869/0385 www.7layers.com Commerzbank AG Account No. 303 016 000 Bank Code 300 400 00 IBAN DE81 3004 0000 0303 0160 00 Swift Code COBADEFF

Table of Contents 1 Applied Standards and Test Summary 3 1.1 Applied Standards 3 1.2 FCC-IC Correlation Table 4 1.3 Measurement Summary / Signatures 5 2 Administrative Data 8 2.1 Testing Laboratory 8 2.2 Project Data 8 2.3 Applicant Data 8 2.4 Manufacturer Data 8 3 Test object Data 9 3.1 General EUT Description 9 3.2 EUT Main components 10 3.3 Ancillary Equipment 10 3.4 Auxiliary Equipment 10 3.5 EUT Setups 11 3.6 Operating Modes 12 3.7 Product labelling 12 4 Test Results 13 4.1 Peak Power Output 13 4.2 Transmitter Spurious Radiated Emissions 15 4.3 Band Edge Compliance Radiated 20 5 Test Equipment 23 6 Antenna Factors, Cable Loss and Sample Calculations 25 6.1 LISN R&S ESH3-Z5 (150 kHz – 30 MHz) 25 6.2 Antenna R&S HFH2-Z2 (9 kHz – 30 MHz) 26 6.3 Antenna R&S HL562 (30 MHz – 1 GHz) 27 6.4 Antenna R&S HF907 (1 GHz – 18 GHz) 28 6.5 Antenna EMCO 3160-09 (18 GHz – 26.5 GHz) 29 6.6 Antenna EMCO 3160-10 (26.5 GHz – 40 GHz) 30 7 Setup Drawings 31 8 Measurement Uncertainties 32 9 Photo Report 32 TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 2 of 32

1 APPLIED STANDARDS AND TEST SUMMARY 1.1 APPLIED STANDARDS Type of Authorization Certification for an Intentional Radiator. Applicable FCC Rules Prepared in accordance with the requirements of FCC Rules and Regulations as listed in 47 CFR Ch.1 Parts 2 and 15 (10-1-15 Edition). The following subparts are applicable to the results in this test report. Part 2, Subpart J - Equipment Authorization Procedures, Certification Part 15, Subpart C – Intentional Radiators § 15.201 Equipment authorization requirement § 15.207 Conducted limits § 15.209 Radiated emission limits; general requirements § 15.247 Operation within the bands 902-928 MHz, 2400-2483.5 MHz Note 1: (DTS Equipment) The tests were selected and performed with reference to the FCC Public Notice “Guidance for Performing Compliance Measurements on Digital Transmission Systems (DTS) Operating Under §15.247, 558074 D01 15.247 Meas Guidance v05, 2018-08-24”. ANSI C63.10–2013 is applied. TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 3 of 32

Summary Test Results: The EUT complied with all performed tests as listed in chapter 1.3 Measurement Summary / Signatures. 1.2 FCC-IC CORRELATION TABLE Correlation of measurement requirements for DTS (e.g. WLAN 2.4 GHz, BT LE) equipment from FCC and IC DTS equipment Measurement FCC reference IC reference Conducted emissions on AC § 15.207 RSS-Gen Issue 4: 8.8 Mains Occupied bandwidth § 15.247 (a) (2) RSS-247 Issue 2: 5.2 (a) Peak conducted output § 15.247 (b) (3), (4) RSS-247 Issue 2: 5.4 (d) power Transmitter spurious RF § 15.247 (d) RSS-Gen Issue 4: 6.13 / conducted emissions 8.9/8.10; RSS-247 Issue 2: 5.5 Transmitter spurious § 15.247 (d); RSS-Gen Issue 4: 6.13 / radiated emissions § 15.209 (a) 8.9/8.10; RSS-247 Issue 2: 5.5 Band edge compliance § 15.247 (d) RSS-247 Issue 2: 5.5 Power density § 15.247 (e) RSS-247 Issue 2: 5.2 (b) Antenna requirement § 15.203 / 15.204 RSS-Gen Issue 4: 8.3 Receiver spurious emissions – – TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 4 of 32

1.3 MEASUREMENT SUMMARY / SIGNATURES 47 CFR CHAPTER I FCC PART 15 Subpart C § 15.207 §15.247 Conducted Emissions at AC Mains The measurement was performed according to ANSI C63.10 Final Result OP-Mode Setup FCC IC Operating mode - - N/P N/P 47 CFR CHAPTER I FCC PART 15 Subpart C § 15.247 (a) (2) §15.247 Occupied Bandwidth (6 dB) The measurement was performed according to ANSI C63.10 Final Result OP-Mode Setup FCC IC Radio Technology, Operating Frequency - - N/P N/P 47 CFR CHAPTER I FCC PART 15 Subpart C IC RSS-Gen & IC TRC; Ch. 6.6 & §15.247 Ch. 8 Occupied Bandwidth (99%) The measurement was performed according to ANSI C63.10 Final Result OP-Mode Setup FCC IC Radio Technology, Operating Frequency - - N/P N/P 47 CFR CHAPTER I FCC PART 15 Subpart C § 15.247 (b) (3) §15.247 Peak Power Output The measurement was performed according to ANSI C63.10 Final Result OP-Mode Setup FCC IC Radio Technology, Operating Frequency, Measurement method WLAN b, high, conducted S01_AA01 Passed Passed WLAN b, low, conducted S01_AA01 Passed Passed WLAN b, mid, conducted S01_AA01 Passed Passed 47 CFR CHAPTER I FCC PART 15 Subpart C § 15.247 (d) §15.247 Spurious RF Conducted Emissions and Conducted Emissions in Restricted Bands The measurement was performed according to ANSI C63.10 Final Result OP-Mode Setup FCC IC Radio Technology, Operating Frequency, Measurement method - - N/P N/P TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 5 of 32

47 CFR CHAPTER I FCC PART 15 Subpart C § 15.247 (d) §15.247 Transmitter Spurious Radiated Emissions The measurement was performed according to ANSI C63.10 Final Result OP-Mode Setup FCC IC Radio Technology, Operating Frequency, Measurement range WLAN b, high, 1 GHz - 26 GHz S02_AA01 Passed Passed 47 CFR CHAPTER I FCC PART 15 Subpart C § 15.247 (d) §15.247 Band Edge Compliance Conducted The measurement was performed according to ANSI C63.10 Final Result OP-Mode Setup FCC IC Radio Technology, Operating Frequency, Band Edge - - N/P N/P 47 CFR CHAPTER I FCC PART 15 Subpart C § 15.247 (d) §15.247 Band Edge Compliance Radiated The measurement was performed according to ANSI C63.10 Final Result OP-Mode Setup FCC IC Radio Technology, Operating Frequency, Band Edge WLAN b, high, high S02_AA01 Passed Passed 47 CFR CHAPTER I FCC PART 15 Subpart C § 15.247 (e) §15.247 Power Density The measurement was performed according to ANSI C63.10 Final Result OP-Mode Setup FCC IC Radio Technology, Operating Frequency - - N/P N/P N/A: Not applicable N/P: Not performed TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 6 of 32

/ Zlayers =/ A Bureau Veritas Group Company According to the applicants information the tested variant JODY—W163—13A of the JODY—W1 family is identical to the already tested variant JODY—W164—03A except for the filter in the WLAN 2.4 GHz antenna path, that has however already been tested in that configuration for variant JODY—W164—07A. Due to this only spot checks for WLAN 2.4 GHz were performed for a class 2 permissive change. Reference to reports of the other variants: MDE_UBLOX_1701_FCCa (W164—03A) MDE_UBLOX_1701_FCCd (W164—07A) liL (responsible for accreditation scope) D bube (responsible for testing and report) Dipl.—Ing. Marco Kullik Dipl.—Ing. Daniel Gall ) Ratingen, Garmany Phone +49 (0)2102 749 0 TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 7 of 32

2 ADMINISTRATIVE DATA 2.1 TESTING LABORATORY Company Name: 7layers GmbH Address: Borsigstr. 11 40880 Ratingen Germany This facility has been fully described in a report submitted to the ISED and accepted under the registration number: Site# 3699A-1. The test facility is also accredited by the following accreditation organisation: Laboratory accreditation no: DAkkS D-PL-12140-01-00 FCC Designation Number: DE0015 FCC Test Firm Registration: 929146 Responsible for accreditation scope: Dipl.-Ing. Marco Kullik Report Template Version: 2017-07-14 2.2 PROJECT DATA Responsible for testing and report: Dipl.-Ing. Daniel Gall Employees who performed the tests: documented internally at 7Layers Date of Report: 2019-01-11 Testing Period: 2018-10-30 to 2018-11-08 2.3 APPLICANT DATA Company Name: u-blox AG Address: Zürcherstrasse 68 8800 Thalwil Switzerland Contact Person: Mr. Filip Kruzela 2.4 MANUFACTURER DATA Company Name: Please see applicant data TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 8 of 32

3 TEST OBJECT DATA 3.1 GENERAL EUT DESCRIPTION Kind of Device The EUT is a module supporting WLAN in the 2.4 GHz and 5 GHz product description bands as well as Bluetooth (BT) 4.2 including Bluetooth Low Energy (BT LE) Product name JODY-W163-13A Type JODY-W163-13A Declared EUT data by the supplier Voltage Type DC Voltage Level 3.3 V Tested Modulation BT: GFSK Modulation, DHx packets (Bluetooth and Bluetooth Low Types and Data Rates Energy), 1 Mbps π/4 DQPSK Modulation, 2-DHx packets, 2 Mbps 8-DPSK Modulation, 3-DHx packets, 3 Mbps WLAN: Mode b: DSSS Modulation, 1Mbps Mode g/n: OFDM Modulation, 6Mbps / MCS 0 (20 MHz only) Specific product The JODY-W1 is a compact automotive grade module that provides description for the EUT Wi-Fi, Bluetooth, and Bluetooth low energy communication. The JODY-W163-13A module can be operated in the following modes: Wi-Fi 2x2 MIMO 802.11n/ac in the 5 GHz band Wi-Fi 1x1 802.11ac in 2.4 / 5 GHz real simultaneous dual band Dual-mode Bluetooth v4.2, can be operated fully simultaneous with both the Wi-Fi modes It is equipped with two antenna pins connected to two SMA antenna connectors on the evaluation board. Maximum supported band width in 2.4 GHz WLAN mode: 20 MHz, 5 GHz WLAN mode: 80 MHz The EUT provides the DC Power Supply following ports: Antenna ports Signal ports Special software used The test modes were set using scripts that were run on a board for testing computer with linux operating system provided by the applicant. The main components of the EUT are listed and described in chapter 3.2 EUT Main components. , TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 9 of 32

3.2 EUT MAIN COMPONENTS Sample Name Sample Code Description EUT A DE1015102aa01 Module on evaluation board Sample Parameter Value Integral Antenna None, two external 50 Ohm connectors on evaluation board. Antenna gain used for evaluation of test results: 2dBi Serial No. D70D4CA6ED205200100 HW Version 00 SW Version P8.1 Comment NOTE:The short description is used to simplify the identification of the EUT in this test report. 3.3 ANCILLARY EQUIPMENT For the purposes of this test report, ancillary equipment is defined as equipment which is used in conjunction with the EUT to provide operational and control features to the EUT. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Ancillary Equipment can influence the test results. Device Details Description (Manufacturer, Type Model, OUT Code) Evaluation Board UBLOX, REV. B, - , - Board the EUT is mounted to, providing ports to the EUT (DC, Antennas, wired communication) 3.4 AUXILIARY EQUIPMENT For the purposes of this test report, auxiliary equipment is defined as equipment which is used temporarily to enable operational and control features especially used for the tests of the EUT which is not used during normal operation or equipment that is used during the tests in combination with the EUT but is not subject of this test report. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Auxiliary Equipment can influence the test results. Device Details Description (Manufacturer, HW, SW, S/N) Board Computer Toradex, Ixora, - , -, - Computer used for setting the test modes TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 10 of 32

3.5 EUT SETUPS This chapter describes the combination of EUTs and equipment used for testing. The rationale for selecting the EUTs, ancillary and auxiliary equipment and interconnecting cables, is to test a representative configuration meeting the requirements of the referenced standards. Setup Combination of EUTs Description and Rationale S01_AA01 EUT A, Evaluation Board, Board Computer Representative setup conducted tests S02_AA01 EUT A, Evaluation Board Representative setup radiated tests TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 11 of 32

3.6 OPERATING MODES This chapter describes the operating modes of the EUTs used for testing. 3.6.1 TEST CHANNELS 2.4 GHz ISM WLAN 2400 - 2483.5 MHz 20 MHz Test Channels: Low Mid High Channel: 1 6 11 Frequency [MHz] 2412 2437 2462 Output power per channel and mode to be set in EUT WLAN script acc. to customer declaration: Channel No. 1 2 3 4 5 6 7 8 9 10 11 Channel freq. 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 [MHz] WLAN mode b 18 18 18 18 18 18 18 18 18 18 18 WLAN mode g 13 15 15 15 15 15 15 15 15 15 13 WLAN mode n 13 15 15 15 15 15 15 15 15 15 13 3.7 PRODUCT LABELLING 3.7.1 FCC ID LABEL Please refer to the documentation of the applicant. 3.7.2 LOCATION OF THE LABEL ON THE EUT Please refer to the documentation of the applicant. TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 12 of 32

4 TEST RESULTS 4.1 PEAK POWER OUTPUT Standard FCC Part 15 Subpart C The test was performed according to: ANSI C63.10 4.1.1 TEST DESCRIPTION The Equipment Under Test (EUT) was set up to perform the output power measurements. The results recorded were measured with the modulation which produces the worst-case (highest) output power. The reference level of the spectrum analyzer was set higher than the output power of the EUT. Conducted power: The EUT was connected to a power meter via a short coax cable with a known loss. 4.1.2 TEST REQUIREMENTS / LIMITS DTS devices: FCC Part 15, Subpart C, §15.247 (b) (3) For systems using digital modulation techniques in the 902-928 MHz, 2400-2483.5 MHz and 5725-5850 MHz bands: 1 watt. ==> Maximum conducted peak output power: 30 dBm (excluding antenna gain, if antennas with directional gains that do not exceed 6 dBi are used). Frequency Hopping Systems: FCC Part 15, Subpart C, §15.247 (b) (1) For frequency hopping systems operating in the 2400-2483.5 MHz band employing at least 75 non-overlapping hopping channels, and all frequency hopping systems in the 5725-5850 MHz band: 1 watt. For all other frequency hopping systems in the 2400-2483.5 MHz band: 0.125 watts. FCC Part 15, Subpart C, §15.247 (b) (2) For frequency hopping systems operating in the 902-928 MHz band: 1 watt for systems employing at least 50 hopping channels; and, 0.25 watts for systems employing less than 50 hopping channels, but at least 25 hopping channels, as permitted under paragraph (a)(1)(i) of this section. Used conversion factor: Limit (dBm) = 10 log (Limit (W)/1mW) TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 13 of 32

4.1.3 TEST PROTOCOL Ambient temperature: 24 °C Air Pressure: 1010 hPa Humidity: 40 % WLAN b-Mode; 20 MHz; 1 Mbit/s Band Channel Frequency RMS Power Limit Margin to Limit E.I.R.P No. [MHz] [dBm] [dBm] [dB] [dBm] 2.4 GHz ISM 1 2412 17.5 30.0 12.5 19.5 6 2437 16.7 30.0 13.3 18.7 11 2462 17.3 30.0 12.7 19.3 Remark: None. 4.1.4 TEST EQUIPMENT USED - R&S TS8997 TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 14 of 32

4.2 TRANSMITTER SPURIOUS RADIATED EMISSIONS Standard FCC Part 15 Subpart C The test was performed according to: ANSI C63.10 4.2.1 TEST DESCRIPTION The test set-up was made in accordance to the general provisions of ANSI C63.10 in a typical installation configuration. The Equipment Under Test (EUT) was set up on a non-conductive table 1.0 x 2.0 m² in the semi-anechoic chamber. The influence of the EUT support table that is used between 30–1000 MHz was evaluated. The measurement procedure is implemented into the EMI test software EMC32 from R&S. Exploratory tests are performed at 3 orthogonal axes to determine the worst-case orientation of a body-worn or handheld EUT. The final test on all kind of EUTs is also performed at 3 axes. A pre-check is performed while the EUT is powered from a DC power source. 1. Measurement up to 30 MHz The Loop antenna HFH2-Z2 is used. Step 1: pre measurement • Anechoic chamber • Antenna distance: 3 m • Detector: Peak-Maxhold • Frequency range: 0.009 - 0.15 MHz and 0.15 – 30 MHz • Frequency steps: 0.05 kHz and 2.25 kHz • IF–Bandwidth: 0.2 kHz and 9 kHz • Measuring time / Frequency step: 100 ms (FFT-based) Intention of this step is, to determine the radiated EMI-profile of the EUT. Afterwards the relevant emissions for the final measurement are identified. Step 2: final measurement For the relevant emissions determined in step 1, an additional measurement with the following settings will be performed. Intention of this step is to find the maximum emission level. • Open area test side • Antenna distance: according to the Standard • Detector: Quasi-Peak • Frequency range: 0.009 – 30 MHz • Frequency steps: measurement at frequencies detected in step 1 • IF–Bandwidth: 0.2 - 10 kHz • Measuring time / Frequency step: 1 s 2. Measurement above 30 MHz and up to 1 GHz Step 1: Preliminary scan This is a preliminary test to identify the highest amplitudes relative to the limit. Settings for step 1: - Antenna distance: 3 m TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 15 of 32

- Detector: Peak-Maxhold / Quasipeak (FFT-based) - Frequency range: 30 – 1000 MHz - Frequency steps: 30 kHz - IF–Bandwidth: 120 kHz - Measuring time / Frequency step: 100 ms - Turntable angle range: –180° to 90° - Turntable step size: 90° - Height variation range: 1 – 3 m - Height variation step size: 2 m - Polarisation: Horizontal + Vertical Intention of this step is, to determine the radiated EMI-profile of the EUT. Afterwards the relevant emissions for the final measurement are identified. Step 2: Adjustment measurement In this step the accuracy of the turntable azimuth and antenna height will be improved. This is necessary to find out the maximum value of every frequency. For each frequency, which was determined the turntable azimuth and antenna height will be adjusted. The turntable azimuth will slowly vary by ± 45° around this value. During this action, the value of emission is continuously measured. The turntable azimuth at the highest emission will be recorded and adjusted. In this position, the antenna height will also slowly vary by ± 100 cm around the antenna height determined. During this action, the value of emission is also continuously measured. The antenna height of the highest emission will also be recorded and adjusted. - Detector: Peak – Maxhold - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 100 ms - Turntable angle range: ± 45 ° around the determined value - Height variation range: ± 100 cm around the determined value - Antenna Polarisation: max. value determined in step 1 Step 3: Final measurement with QP detector With the settings determined in step 3, the final measurement will be performed: EMI receiver settings for step 4: - Detector: Quasi-Peak (< 1 GHz) - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 1 s After the measurement a plot will be generated which contains a diagram with the results of the preliminary scan and a chart with the frequencies and values of the results of the final measurement. 3. Measurement above 1 GHz The following modifications apply to the measurement procedure for the frequency range above 1 GHz: Step 1: The Equipment Under Test (EUT) was set up on a non-conductive support (tilt device) at 1.5 m height in the fully-anechoic chamber. All steps were performed with one height (1.5 m) of the receiving antenna only. The EUT is turned during the preliminary measurement across the elevation axis, with a step size of 90 °. The turn table step size (azimuth angle) for the preliminary measurement is 45 °. Step 2: TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 16 of 32

Due to the fact, that in this frequency range the test is performed in a fully anechoic room, the height scan of the receiving antenna instep 2 is omitted. Instead of this, a maximum search with a step size ± 45° for the elevation axis is performed. The turn table azimuth will slowly vary by ± 22.5°. The elevation angle will slowly vary by ± 45° EMI receiver settings (for all steps): - Detector: Peak, Average - IF Bandwidth = 1 MHz Step 3: Spectrum analyser settings for step 3: - Detector: Peak / Average - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 1 MHz - Measuring time: 1 s 4.2.2 TEST REQUIREMENTS / LIMITS FCC Part 15, Subpart C, §15.247 (d) ... In addition, radiated emissions which fall in the restricted bands, as defined in Section 15.205(a), must also comply with the radiated emission limits specified in Section 15.209(a) (see Section 15.205(c)). FCC Part 15, Subpart C, §15.209, Radiated Emission Limits Measurement Frequency in MHz Limit (µV/m) Limits (dBµV/m) distance (m) 0.009 – 0.49 2400/F(kHz)@300m 3 (48.5 – 13.8)@300m 0.49 – 1.705 24000/F(kHz)@30m 3 (33.8 – 23.0)@30m 1.705 – 30 30@30m 3 29.5@30m The measured values are corrected with an inverse linear distance extrapolation factor (40 dB/decade) according FCC 15.31 (2). Measurement Frequency in MHz Limit (µV/m) Limits (dBµV/m) distance (m) 30 – 88 100@3m 3 40.0@3m 88 – 216 150@3m 3 43.5@3m 216 – 960 200@3m 3 46.0@3m 960 - 26000 500@3m 3 54.0@3m 26000 - 40000 500@3m 1 54.0@3m The measured values above 26 GHz are corrected with an inverse linear distance extrapolation factor (20 dB/decade). §15.35(b) ..., there is also a limit on the radio frequency emissions, as measured using instrumentation with a peak detector function, corresponding to 20 dB above the maximum permitted average limit.... Used conversion factor: Limit (dBµV/m) = 20 log (Limit (µV/m)/1µV/m) TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 17 of 32

4.2.3 TEST PROTOCOL Ambient temperature: 26 °C Air Pressure: 1014 hPa Humidity: 37 % WLAN b-Mode; 20 MHz; 1 Mbit/s Applied duty cycle correction (AV): 0 dB Ch. Center Spurious Spurious Margin to Freq. Freq. Level Detec- RBW Limit Limit Ch. No. [MHz] [MHz] [dBµV/m] tor [kHz] [dBµV/m] [dB] Limit Type 11 2462 --- --- --- --- --- --- RB Remark: Antenna port of EUT terminated with 50 Ohm. Please see next sub-clause for the measurement plot. TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 18 of 32

4.2.4 MEASUREMENT PLOT (SHOWING THE HIGHEST VALUE, “WORST CASE”) Radio Technology = WLAN b, Operating Frequency = high, Measurement range = 1 GHz - 26 GHz (S02_AA01) Level in dBµV/m Critical_Freqs Frequency MaxPeak Average Limit Margi Meas. Bandwidt Heigh Pol Azimut Elevatio (MHz) (dBµV/m) (dBµV/m) (dBµV/m) n Time h t h n (dB) (ms) (kHz) (cm) (deg) (deg) 2485.068 49.9 --- 74.00 24.06 --- --- 150.0 V -100.0 15.0 2485.068 --- 38.1 54.00 15.89 --- --- 150.0 H 92.0 15.0 Final_Result Frequency MaxPeak CAverage Limit Margi Meas. Bandwidt Heigh Pol Azimut Elevatio (MHz) (dBµV/m) (dBµV/m) (dBµV/m) n Time h t h n (dB) (ms) (kHz) (cm) (deg) (deg) 2485.068 --- 35.6 54.00 18.42 1000.0 1000.000 150.0 H 92.0 15.0 2485.068 48.3 --- 74.00 25.72 1000.0 1000.000 150.0 V -100.0 15.0 4.2.5 TEST EQUIPMENT USED - Radiated Emissions TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 19 of 32

4.3 BAND EDGE COMPLIANCE RADIATED Standard FCC Part 15 Subpart C The test was performed according to: ANSI C63.10 4.3.1 TEST DESCRIPTION Please see test description for the test case “Spurious Radiated Emissions” 4.3.2 TEST REQUIREMENTS / LIMITS For band edges connected to a restricted band, the limits are specified in Section 15.209(a) FCC Part 15, Subpart C, §15.209, Radiated Emission Limits Measurement Frequency in MHz Limit (µV/m) Limits (dBµV/m) distance (m) 0.009 – 0.49 2400/F(kHz)@300m 3 (48.5 – 13.8)@300m 0.49 – 1.705 24000/F(kHz)@30m 3 (33.8 – 23.0)@30m 1.705 – 30 30@30m 3 29.5@30m The measured values are corrected with an inverse linear distance extrapolation factor (40 dB/decade) according FCC 15.31 (2). Measurement Frequency in MHz Limit (µV/m) Limits (dBµV/m) distance (m) 30 – 88 100@3m 3 40.0@3m 88 – 216 150@3m 3 43.5@3m 216 – 960 200@3m 3 46.0@3m 960 - 26000 500@3m 3 54.0@3m 26000 - 40000 500@3m 1 54.0@3m The measured values above 26 GHz are corrected with an inverse linear distance extrapolation factor (20 dB/decade). §15.35(b) ..., there is also a limit on the radio frequency emissions, as measured using instrumentation with a peak detector function, corresponding to 20 dB above the maximum permitted average limit.... Used conversion factor: Limit (dBµV/m) = 20 log (Limit (µV/m)/1µV/m) TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 20 of 32

4.3.3 TEST PROTOCOL Ambient temperature: 26 °C Air Pressure: 1014 hPa Humidity: 37 % WLAN b-Mode; 20 MHz; 1 Mbit/s Applied duty cycle correction (AV): 0 dB Ch. Ch. Center Band Edge Spurious Level Detec- RBW Limit Margin to Limit No. Freq. Freq. [MHz] [dBµV/m] tor [kHz] [dBµV/m] Limit [dB] Type [MHz] 11 2462 2483.5 48.3 PEAK 1000 74.0 25.6 BE 11 2462 2483.5 35.6 AV 1000 54.0 18.4 BE Remark: Antenna port of EUT terminated with 50 Ohm. Please see next sub-clause for the measurement plot. TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 21 of 32

4.3.4 MEASUREMENT PLOT (SHOWING THE HIGHEST VALUE, “WORST CASE”) Radio Technology = WLAN b, Operating Frequency = high, Band Edge = high (S02_AA01) Level in dBµV/m Critical_Freqs Frequency MaxPeak Average Limit Margi Meas. Bandwidt Heigh Pol Azimut Elevatio (MHz) (dBµV/m) (dBµV/m) (dBµV/m) n Time h t h n (dB) (ms) (kHz) (cm) (deg) (deg) 2485.068 49.9 --- 74.00 24.06 --- --- 150.0 V -100.0 15.0 2485.068 --- 38.1 54.00 15.89 --- --- 150.0 H 92.0 15.0 Final_Result Frequency MaxPeak CAverage Limit Margi Meas. Bandwidt Heigh Pol Azimut Elevatio (MHz) (dBµV/m) (dBµV/m) (dBµV/m) n Time h t h n (dB) (ms) (kHz) (cm) (deg) (deg) 2485.068 --- 35.6 54.00 18.42 1000.0 1000.000 150.0 H 92.0 15.0 2485.068 48.3 --- 74.00 25.72 1000.0 1000.000 150.0 V -100.0 15.0 4.3.5 TEST EQUIPMENT USED - Radiated Emissions TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 22 of 32

5 TEST EQUIPMENT 1 R&S TS8997 EN300328/301893 Test Lab Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 1.1 SMB100A Signal Rohde & Schwarz 107695 2017-07 2020-07 Generator 9 kHz - 6 GHz 1.2 MFS Rubidium Datum-Beverly 5489/001 2018-07 2019-07 Frequency Standard 1.3 1515 / 93459 Broadband Weinschel LN673 Power Divider Associates SMA (Aux) 1.4 FSV30 Signal Rohde & Schwarz 103005 2018-04 2020-04 Analyzer 10 Hz - 30 GHz 1.5 Fluke 177 Digital Fluke Europe B.V. 86670383 2018-04 2020-04 Multimeter 03 (Multimeter) 1.6 VT 4002 Climatic Vötsch 58566002150010 2018-04 2020-04 Chamber 1.7 A8455-4 4 Way Power - Divider (SMA) 1.8 Opus10 THI ThermoHygro Lufft Mess- und 7482 2017-03 2019-03 (8152.00) Datalogger 03 Regeltechnik GmbH (Environ) 1.9 SMBV100A Vector Signal Rohde & Schwarz 259291 2016-10 2019-10 Generator 9 kHz - 6 GHz 1.10 OSP120 Switching Unit Rohde & Schwarz 101158 2018-05 2021-05 with integrated power meter 2 Radiated Emissions Lab to perform radiated emission tests Ref.No. Device Description Manufacturer Serial Number Last Calibration Name Calibration Due 2.1 NRV-Z1 Sensor Head A Rohde & Schwarz 827753/005 2018-07 2019-07 2.2 MFS Rubidium Datum GmbH 002 2018-10 2020-10 Frequency Normal MFS 2.3 Opus10 TPR ThermoAirpressur Lufft Mess- und 13936 2017-04 2019-04 (8253.00) e Datalogger 13 Regeltechnik GmbH (Environ) 2.4 Anechoic 10.58 x 6.38 x Frankonia none 2016-05 2019-05 Chamber 6.00 m³ 2.5 HL 562 Ultralog new Rohde & Schwarz 830547/003 2018-07 2021-07 biconicals 2.6 5HC2700/12 High Pass Filter Trilithic 9942012 750-1.5-KK 2.7 ASP 1.2/1.8- Antenna Mast Maturo GmbH - 10 kg TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 23 of 32

Ref.No. Device Description Manufacturer Serial Number Last Calibration Name Calibration Due 2.8 Fully 8.80m x 4.60m x Albatross Projects P26971-647-001- 2018-06 2021-06 Anechoic 4.05m (l x w x h) PRB Room 2.9 Fluke 177 Digital Multimeter Fluke Europe B.V. 86670383 2018-04 2020-04 03 (Multimeter) 2.10 JS4- Broadband Miteq 849785 18002600- Amplifier 18 GHz 32-5P - 26 GHz 2.11 FSW 43 Spectrum Rohde & Schwarz 103779 2016-12 2018-12 Analyzer 2.12 3160-09 Standard Gain / EMCO Elektronic 00083069 Pyramidal Horn GmbH Antenna 26.5 GHz 2.13 WHKX High Pass Filter Wainwright 09 7.0/18G-8SS 2.14 4HC1600/12 High Pass Filter Trilithic 9942011 750-1.5-KK 2.15 Chroma 6404 AC Power Source Chroma ATE INC. 64040001304 2.16 JS4- Broadband Miteq 619368 00102600- Amplifier 30 MHz 42-5A - 26 GHz 2.17 TT 1.5 WI Turn Table Maturo GmbH - 2.18 HL 562 Log.-per. Antenna Rohde & Schwarz 100609 2016-04 2019-04 Ultralog 2.19 3160-10 Standard Gain / EMCO Elektronic 00086675 Pyramidal Horn GmbH Antenna 40 GHz 2.20 5HC3500/18 High Pass Filter Trilithic 200035008 000-1.2-KK 2.21 HFH2-Z2 Loop Antenna Rohde & Schwarz 829324/006 2018-01 2021-01 2.22 Opus10 THI ThermoHygro Lufft Mess- und 12482 2017-03 2019-03 (8152.00) Datalogger 12 Regeltechnik GmbH (Environ) 2.23 ESR 7 EMI Receiver / Rohde & Schwarz 101424 2016-11 2018-11 Spectrum Analyzer 2.24 JS4- Broadband Miteq 896037 00101800- Amplifier 30 MHz 35-5P - 18 GHz 2.25 AS 620 P Antenna mast HD GmbH 620/37 2.26 Tilt device Antrieb TD1.5- Maturo GmbH TD1.5- Maturo 10kg 10kg/024/37907 (Rohacell) 09 2.27 ESIB 26 Spectrum Rohde & Schwarz 830482/004 2018-01 2020-01 Analyzer 2.28 PAS 2.5 - 10 Antenna Mast Maturo GmbH - kg 2.29 AM 4.0 Antenna mast Maturo GmbH AM4.0/180/1192 0513 2.30 HF 907 Double-ridged Rohde & Schwarz 102444 2018-07 2021-07 horn The calibration interval is the time interval between “Last Calibration” and “Calibration Due” TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 24 of 32

6 ANTENNA FACTORS, CABLE LOSS AND SAMPLE CALCULATIONS This chapter contains the antenna factors with their corresponding path loss of the used measurement path for all antennas as well as the insertion loss of the LISN. 6.1 LISN R&S ESH3-Z5 (150 KHZ – 30 MHZ) cable LISN loss insertion (incl. 10 loss dB ESH3- atten- Frequency Corr. Z5 uator) MHz dB dB dB 0.15 10.1 0.1 10.0 5 10.3 0.1 10.2 7 10.5 0.2 10.3 10 10.5 0.2 10.3 12 10.7 0.3 10.4 14 10.7 0.3 10.4 16 10.8 0.4 10.4 18 10.9 0.4 10.5 20 10.9 0.4 10.5 22 11.1 0.5 10.6 24 11.1 0.5 10.6 26 11.2 0.5 10.7 28 11.2 0.5 10.7 30 11.3 0.5 10.8 Sample calculation ULISN (dB µV) = U (dB µV) + Corr. (dB) U = Receiver reading LISN Insertion loss = Voltage Division Factor of LISN Corr. = sum of single correction factors of used LISN, cables, switch units (if used) Linear interpolation will be used for frequencies in between the values in the table. TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 25 of 32

6.2 ANTENNA R&S HFH2-Z2 (9 KHZ – 30 MHZ) cable cable cable cable distance dLimit dused loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. AF (inside (outside (switch (to (-40 dB/ distance distance Frequency HFH-Z2) Corr. chamber) chamber) unit) receiver) decade) (limit) (used) MHz dB (1/m) dB dB dB dB dB dB m m 0.009 20.50 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.01 20.45 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.015 20.37 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.02 20.36 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.025 20.38 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.03 20.32 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.05 20.35 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.08 20.30 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.1 20.20 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.2 20.17 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.3 20.14 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.49 20.12 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.490001 20.12 -39.6 0.1 0.1 0.1 0.1 -40 30 3 0.5 20.11 -39.6 0.1 0.1 0.1 0.1 -40 30 3 0.8 20.10 -39.6 0.1 0.1 0.1 0.1 -40 30 3 1 20.09 -39.6 0.1 0.1 0.1 0.1 -40 30 3 2 20.08 -39.6 0.1 0.1 0.1 0.1 -40 30 3 3 20.06 -39.6 0.1 0.1 0.1 0.1 -40 30 3 4 20.05 -39.5 0.2 0.1 0.1 0.1 -40 30 3 5 20.05 -39.5 0.2 0.1 0.1 0.1 -40 30 3 6 20.02 -39.5 0.2 0.1 0.1 0.1 -40 30 3 8 19.95 -39.5 0.2 0.1 0.1 0.1 -40 30 3 10 19.83 -39.4 0.2 0.1 0.2 0.1 -40 30 3 12 19.71 -39.4 0.2 0.1 0.2 0.1 -40 30 3 14 19.54 -39.4 0.2 0.1 0.2 0.1 -40 30 3 16 19.53 -39.3 0.3 0.1 0.2 0.1 -40 30 3 18 19.50 -39.3 0.3 0.1 0.2 0.1 -40 30 3 20 19.57 -39.3 0.3 0.1 0.2 0.1 -40 30 3 22 19.61 -39.3 0.3 0.1 0.2 0.1 -40 30 3 24 19.61 -39.3 0.3 0.1 0.2 0.1 -40 30 3 26 19.54 -39.3 0.3 0.1 0.2 0.1 -40 30 3 28 19.46 -39.2 0.3 0.1 0.3 0.1 -40 30 3 30 19.73 -39.1 0.4 0.1 0.3 0.1 -40 30 3 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) distance correction = -40 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 26 of 32

6.3 ANTENNA R&S HL562 (30 MHZ – 1 GHZ) (dLimit = 3 m) cable cable cable cable distance dLimit dused AF loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. R&S (inside (outside (switch (to (-20 dB/ distance distance Frequency HL562 Corr. chamber) chamber) unit) receiver) decade) (limit) (used) MHz dB (1/m) dB dB dB dB dB dB m m 30 18.6 0.6 0.29 0.04 0.23 0.02 0.0 3 3 50 6.0 0.9 0.39 0.09 0.32 0.08 0.0 3 3 100 9.7 1.2 0.56 0.14 0.47 0.08 0.0 3 3 150 7.9 1.6 0.73 0.20 0.59 0.12 0.0 3 3 200 7.6 1.9 0.84 0.21 0.70 0.11 0.0 3 3 250 9.5 2.1 0.98 0.24 0.80 0.13 0.0 3 3 300 11.0 2.3 1.04 0.26 0.89 0.15 0.0 3 3 350 12.4 2.6 1.18 0.31 0.96 0.13 0.0 3 3 400 13.6 2.9 1.28 0.35 1.03 0.19 0.0 3 3 450 14.7 3.1 1.39 0.38 1.11 0.22 0.0 3 3 500 15.6 3.2 1.44 0.39 1.20 0.19 0.0 3 3 550 16.3 3.5 1.55 0.46 1.24 0.23 0.0 3 3 600 17.2 3.5 1.59 0.43 1.29 0.23 0.0 3 3 650 18.1 3.6 1.67 0.34 1.35 0.22 0.0 3 3 700 18.5 3.6 1.67 0.42 1.41 0.15 0.0 3 3 750 19.1 4.1 1.87 0.54 1.46 0.25 0.0 3 3 800 19.6 4.1 1.90 0.46 1.51 0.25 0.0 3 3 850 20.1 4.4 1.99 0.60 1.56 0.27 0.0 3 3 900 20.8 4.7 2.14 0.60 1.63 0.29 0.0 3 3 950 21.1 4.8 2.22 0.60 1.66 0.33 0.0 3 3 1000 21.6 4.9 2.23 0.61 1.71 0.30 0.0 3 3 (dLimit = 10 m) 30 18.6 -9.9 0.29 0.04 0.23 0.02 -10.5 10 3 50 6.0 -9.6 0.39 0.09 0.32 0.08 -10.5 10 3 100 9.7 -9.2 0.56 0.14 0.47 0.08 -10.5 10 3 150 7.9 -8.8 0.73 0.20 0.59 0.12 -10.5 10 3 200 7.6 -8.6 0.84 0.21 0.70 0.11 -10.5 10 3 250 9.5 -8.3 0.98 0.24 0.80 0.13 -10.5 10 3 300 11.0 -8.1 1.04 0.26 0.89 0.15 -10.5 10 3 350 12.4 -7.9 1.18 0.31 0.96 0.13 -10.5 10 3 400 13.6 -7.6 1.28 0.35 1.03 0.19 -10.5 10 3 450 14.7 -7.4 1.39 0.38 1.11 0.22 -10.5 10 3 500 15.6 -7.2 1.44 0.39 1.20 0.19 -10.5 10 3 550 16.3 -7.0 1.55 0.46 1.24 0.23 -10.5 10 3 600 17.2 -6.9 1.59 0.43 1.29 0.23 -10.5 10 3 650 18.1 -6.9 1.67 0.34 1.35 0.22 -10.5 10 3 700 18.5 -6.8 1.67 0.42 1.41 0.15 -10.5 10 3 750 19.1 -6.3 1.87 0.54 1.46 0.25 -10.5 10 3 800 19.6 -6.3 1.90 0.46 1.51 0.25 -10.5 10 3 850 20.1 -6.0 1.99 0.60 1.56 0.27 -10.5 10 3 900 20.8 -5.8 2.14 0.60 1.63 0.29 -10.5 10 3 950 21.1 -5.6 2.22 0.60 1.66 0.33 -10.5 10 3 1000 21.6 -5.6 2.23 0.61 1.71 0.30 -10.5 10 3 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) distance correction = -20 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Tables show an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 27 of 32

6.4 ANTENNA R&S HF907 (1 GHZ – 18 GHZ) cable cable loss 3 loss 1 (switch (relay + cable unit, AF cable loss 2 atten- cable R&S inside (outside uator & loss 4 (to Frequency HF907 Corr. chamber) chamber) pre-amp) receiver) MHz dB (1/m) dB dB dB dB dB 1000 24.4 -19.4 0.99 0.31 -21.51 0.79 2000 28.5 -17.4 1.44 0.44 -20.63 1.38 3000 31.0 -16.1 1.87 0.53 -19.85 1.33 4000 33.1 -14.7 2.41 0.67 -19.13 1.31 5000 34.4 -13.7 2.78 0.86 -18.71 1.40 6000 34.7 -12.7 2.74 0.90 -17.83 1.47 7000 35.6 -11.0 2.82 0.86 -16.19 1.46 cable loss 4 cable (switch loss 1 cable cable unit, used AF (relay loss 2 loss 3 atten- cable for R&S inside (inside (outside uator & loss 5 (to FCC Frequency HF907 Corr. chamber) chamber) chamber) pre-amp) receiver) 15.247 MHz dB (1/m) dB dB dB dB dB dB 3000 31.0 -23.4 0.47 1.87 0.53 -27.58 1.33 4000 33.1 -23.3 0.56 2.41 0.67 -28.23 1.31 5000 34.4 -21.7 0.61 2.78 0.86 -27.35 1.40 6000 34.7 -21.2 0.58 2.74 0.90 -26.89 1.47 7000 35.6 -19.8 0.66 2.82 0.86 -25.58 1.46 cable loss 1 cable cable cable cable cable AF (relay loss 2 loss 3 loss 4 loss 5 loss 6 R&S inside (High (pre- (inside (outside (to Frequency HF907 Corr. chamber) Pass) amp) chamber) chamber) receiver) MHz dB (1/m) dB dB dB dB dB dB dB 7000 35.6 -57.3 0.56 1.28 -62.72 2.66 0.94 1.46 8000 36.3 -56.3 0.69 0.71 -61.49 2.84 1.00 1.53 9000 37.1 -55.3 0.68 0.65 -60.80 3.06 1.09 1.60 10000 37.5 -56.2 0.70 0.54 -61.91 3.28 1.20 1.67 11000 37.5 -55.3 0.80 0.61 -61.40 3.43 1.27 1.70 12000 37.6 -53.7 0.84 0.42 -59.70 3.53 1.26 1.73 13000 38.2 -53.5 0.83 0.44 -59.81 3.75 1.32 1.83 14000 39.9 -56.3 0.91 0.53 -63.03 3.91 1.40 1.77 15000 40.9 -54.1 0.98 0.54 -61.05 4.02 1.44 1.83 16000 41.3 -54.1 1.23 0.49 -61.51 4.17 1.51 1.85 17000 42.8 -54.4 1.36 0.76 -62.36 4.34 1.53 2.00 18000 44.2 -54.7 1.70 0.53 -62.88 4.41 1.55 1.91 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. Tables show an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 28 of 32

6.5 ANTENNA EMCO 3160-09 (18 GHZ – 26.5 GHZ) cable cable cable cable cable AF loss 1 loss 2 loss 3 loss 4 loss 5 EMCO (inside (pre- (inside (switch (to Frequency 3160-09 Corr. chamber) amp) chamber) unit) receiver) MHz dB (1/m) dB dB dB dB dB dB 18000 40.2 -23.5 0.72 -35.85 6.20 2.81 2.65 18500 40.2 -23.2 0.69 -35.71 6.46 2.76 2.59 19000 40.2 -22.0 0.76 -35.44 6.69 3.15 2.79 19500 40.3 -21.3 0.74 -35.07 7.04 3.11 2.91 20000 40.3 -20.3 0.72 -34.49 7.30 3.07 3.05 20500 40.3 -19.9 0.78 -34.46 7.48 3.12 3.15 21000 40.3 -19.1 0.87 -34.07 7.61 3.20 3.33 21500 40.3 -19.1 0.90 -33.96 7.47 3.28 3.19 22000 40.3 -18.7 0.89 -33.57 7.34 3.35 3.28 22500 40.4 -19.0 0.87 -33.66 7.06 3.75 2.94 23000 40.4 -19.5 0.88 -33.75 6.92 3.77 2.70 23500 40.4 -19.3 0.90 -33.35 6.99 3.52 2.66 24000 40.4 -19.8 0.88 -33.99 6.88 3.88 2.58 24500 40.4 -19.5 0.91 -33.89 7.01 3.93 2.51 25000 40.4 -19.3 0.88 -33.00 6.72 3.96 2.14 25500 40.5 -20.4 0.89 -34.07 6.90 3.66 2.22 26000 40.5 -21.3 0.86 -35.11 7.02 3.69 2.28 26500 40.5 -21.1 0.90 -35.20 7.15 3.91 2.36 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 29 of 32

6.6 ANTENNA EMCO 3160-10 (26.5 GHZ – 40 GHZ) cable cable cable cable distance dLimit dused AF loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. EMCO (inside (outside (switch (to (-20 dB/ distance distance Frequency 3160-10 Corr. chamber) chamber) unit) receiver) decade) (limit) (used) GHz dB (1/m) dB dB dB dB dB dB m m 26.5 43.4 -11.2 4.4 -15.6 3 0.5 27.0 43.4 -11.2 4.4 -15.6 3 0.5 28.0 43.4 -11.1 4.5 -15.6 3 0.5 29.0 43.5 -11.0 4.6 -15.6 3 0.5 30.0 43.5 -10.9 4.7 -15.6 3 0.5 31.0 43.5 -10.8 4.7 -15.6 3 0.5 32.0 43.5 -10.7 4.8 -15.6 3 0.5 33.0 43.6 -10.7 4.9 -15.6 3 0.5 34.0 43.6 -10.6 5.0 -15.6 3 0.5 35.0 43.6 -10.5 5.1 -15.6 3 0.5 36.0 43.6 -10.4 5.1 -15.6 3 0.5 37.0 43.7 -10.3 5.2 -15.6 3 0.5 38.0 43.7 -10.2 5.3 -15.6 3 0.5 39.0 43.7 -10.2 5.4 -15.6 3 0.5 40.0 43.8 -10.1 5.5 -15.6 3 0.5 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. distance correction = -20 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 30 of 32

7 SETUP DRAWINGS Drawing 1: Setup in the Anechoic chamber. For measurements below 1 GHz the ground was replaced by a conducting groundplane. Drawing 2: Setup for conducted radio tests. TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 31 of 32

8 MEASUREMENT UNCERTAINTIES Test Case Parameter Uncertainty AC Power Line Power ± 3.4 dB Field Strength of spurious radiation Power ± 5.5 dB 6 dB / 26 dB / 99% Bandwidth Power ± 2.9 dB Frequency ± 11.2 kHz Conducted Output Power Power ± 2.2 dB Band Edge Compliance Power ± 2.2 dB Frequency ± 11.2 kHz Frequency Stability Frequency ± 25 Hz Power Spectral Density Power ± 2.2 dB 9 PHOTO REPORT Please see separate photo report. TEST REPORT REFERENCE: MDE_UBLOX_1828_FCCc Page 32 of 32


Document Created: 2019-03-22 03:20:11
Document Modified: 2019-03-22 03:20:11
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC