Test Report Simultaneous TX

FCC ID: XPYJODYW164

Test Report

Download: PDF
FCCID_3927199

FCC Measurement/Technical Report on WLAN and Bluetooth module JODY-W164-03A FCC ID: XPYJODYW164 IC: 8595A-JODYW164 Test Report Reference: MDE_UBLOX_1701_FCCc Test Laboratory: 7layers GmbH Borsigstrasse 11 40880 Ratingen Germany Note: The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts without the written approval of the test laboratory. 7layers GmbH Geschäftsführer/ Borsigstraße 11 Managing Directors: Registergericht/registered: a Bureau Veritas 40880 Ratingen, Germany Frank Spiller Düsseldorf HRB 75554 Group Company T +49 (0) 2102 749 0 Bernhard Retka USt-Id.-Nr./VAT-No. DE203159652 F +49 (0) 2102 749 350 Alexandre Norré-Oudard Steuer-Nr./TAX-No. 147/5869/0385 www.7layers.com Commerzbank AG Account No. 303 016 000 Bank Code 300 400 00 IBAN DE81 3004 0000 0303 0160 00 Swift Code COBADEFF

Table of Contents 1 Applied Standards and Test Summary 3 1.1 Applied Standards 3 1.2 FCC-IC Correlation Table 4 1.3 Measurement Summary / Signatures 5 2 Administrative Data 6 2.1 Testing Laboratory 6 2.2 Project Data 6 2.3 Applicant Data 6 2.4 Manufacturer Data 6 3 Test object Data 7 3.1 General EUT Description 7 3.2 EUT Main components 8 3.3 Ancillary Equipment 8 3.4 Auxiliary Equipment 9 3.5 EUT Setups 9 3.6 Operating Modes 9 3.7 Product labelling 9 4 Test Results 10 4.1 Simultaneous Transmission - Spurious Radiated Emissions 10 5 Test Equipment 15 6 Antenna Factors, Cable Loss and Sample Calculations 17 6.1 LISN R&S ESH3-Z5 (150 kHz – 30 MHz) 17 6.2 Antenna R&S HFH2-Z2 (9 kHz – 30 MHz) 18 6.3 Antenna R&S HL562 (30 MHz – 1 GHz) 19 6.4 Antenna R&S HF907 (1 GHz – 18 GHz) 20 6.5 Antenna EMCO 3160-09 (18 GHz – 26.5 GHz) 21 6.6 Antenna EMCO 3160-10 (26.5 GHz – 40 GHz) 22 7 Setup Drawings 23 8 Measurement Uncertainties 24 9 Photo Report 24 TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCc Page 2 of 24

1 APPLIED STANDARDS AND TEST SUMMARY 1.1 APPLIED STANDARDS Type of Authoriiation Certification for an Intentional Radiator. Applicable FCC Rules Prepared in accordance with the requirements of FCC Rules and Regulations as listed in 47 CFR Ch.1 Parts 2 and 15 (10-1-15 Edition). The following subparts are applicable to the results in this test report. Part 2, Subpart J - Equipment Authorization Procedures, Certification Part 15, Subpart C – Intentional Radiators § 15.201 Equipment authorization requirement § 15.207 Conducted limits § 15.209 Radiated emission limits; general requirements § 15.247 Operation within the bands 902-928 MHz, 2400-2483.5 MHz Note 1: (DTS Equipment) The tests were selected and performed with reference to the FCC Public Notice “Guidance for Performing Compliance Measurements on Digital Transmission Systems (DTS) Operating Under §15.247, 558074 D01 DTS Meas Guidance v04, 2017-04-05”. ANSI C63.10–2013 is applied. Note 2: (FHSS Equipment) The tests were selected and performed with reference to the FCC Public Notice DA 00-705, released March 30, 2000. Instead of applying ANSI C63.4-1992 which is referenced in the FCC Public Note, the newer ANSI C63.10-2013 is applied. TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCc Page 3 of 24

Summary Test Results: The EUT complied with all performed tests as listed in chapter 1.3 Measurement Summary / Signatures. 1.2 FCC-IC CORRELATION TABLE Correlation of measurement requirements for DTS (e.g. WLAN 2.4 GHi, BT LE) equipment from FCC and IC DTS equipment Measurement FCC reference IC reference Conducted emissions on AC § 15.207 RSS-Gen Issue 4: 8.8 Mains Occupied bandwidth § 15.247 (a) (2) RSS-247 Issue 2: 5.2 (a) Peak conducted output § 15.247 (b) (3), (4) RSS-247 Issue 2: 5.4 (d) power Transmitter spurious RF § 15.247 (d) RSS-Gen Issue 4: 6.13 / conducted emissions 8.9/8.10; RSS-247 Issue 2: 5.5 Transmitter spurious § 15.247 (d); RSS-Gen Issue 4: 6.13 / radiated emissions § 15.209 (a) 8.9/8.10; RSS-247 Issue 2: 5.5 Band edge compliance § 15.247 (d) RSS-247 Issue 2: 5.5 Power density § 15.247 (e) RSS-247 Issue 2: 5.2 (b) Antenna requirement § 15.203 / 15.204 RSS-Gen Issue 4: 8.3 Receiver spurious emissions – – TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCc Page 4 of 24

%layers A Bureau Veritas Group Company 1.3 MEASUREMENT SUMMARY / SIGNATURES 47 CFR CHAPTER I FCC PART 15 Subpart C § 15.247 (d) §15.247 Simultaneous Transmission — Spurious Radiated Emissions The measurement was performed according to ANSI C63.10 Final Result OP—Mode Setup FCC IC Active Transmitters 2.4 GHz band: Bluetooth hopping, WLAN n mode on 2442 MHz S01_3_AEO1 Passed Passed 5 GHz band: WLAN ac mode on 5210 MHz N/A: Not applicable N/P: Not performed (responsible for accreditation scope) (responsible for testing and report) Dipl.—Ing. Marco Kullik Dipl.—Ing. Daniel Gall 7 layers GmbH, Borsigstr. 11 40880 Ratingen, Germany Phone +49 (0)2102 749 0 TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCc Page 5 of 24

2 ADMINISTRATIVE DATA 2.1 TESTING LABORATORY Company Name: 7layers GmbH Address: Borsigstr. 11 40880 Ratingen Germany This facility has been fully described in a report submitted to the ISED and accepted under the registration number: Site# 3699A-1. The test facility is also accredited by the following accreditation organisation: Laboratory accreditation no: DAkkS D-PL-12140-01-00 FCC Designation Number: DE0015 FCC Test Firm Registration: 929146 Responsible for accreditation scope: Dipl.-Ing. Marco Kullik Report Template Version: 2018-01-10 2.2 PROJECT DATA Responsible for testing and report: Dipl.-Ing. Daniel Gall Employees who performed the tests: documented internally at 7Layers Date of Report: 2018-05-18 Testing Period: 2018-02-14 to 2018-02-21 2.3 APPLICANT DATA Company Name: u-blox AG Address: Zürcherstrasse 68 8800 Thalwil Switzerland Contact Person: Mr. Filip Kruzela 2.4 MANUFACTURER DATA Company Name: Please see applicant data Address: Contact Person: TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCc Page 6 of 24

3 TEST OBJECT DATA 3.1 GENERAL EUT DESCRIPTION Kind of Device The EUT is a module supporting WLAN in the 2.4 GHz and 5 GHz product description bands as well as Bluetooth (BT) 4.2 including Bluetooth Low Energy (BT LE) Product name JODY-W164-03A Type JODY-W164-03A Declared EUT data by the supplier Voltage Type DC Voltage Level 3.3 V Tested Modulation Type No specific mode set since the test mode firmware did not allow to set simultaneous transmission mode. All technologies were tested in normal application mode with throughput test active. Specific product The JODY-W1 is a compact automotive grade module that provides description for the EUT Wi-Fi, Bluetooth, and Bluetooth low energy communication. The JODY-W164-03A module can be operated in the following modes: Wi-Fi 2x2 MIMO 802.11n/ac in the 5 GHz band Wi-Fi 1x1 802.11ac in 2.4 / 5 GHz real simultaneous dual band Dual-mode Bluetooth v4.2, can be operated fully simultaneous with both the Wi-Fi modes It is equipped with two antenna pins connected to two SMA antenna connectors on the evaluation board. Maximum supported band width in 2.4 GHz WLAN mode: 20 MHz, 5 GHz WLAN mode: 80 MHz The EUT provides the DC Power Supply following ports: Antenna ports Signal ports Tested datarates Bluetooth classic (up to 3Mbps), WLAN n mode 2.4 GHz (up to 72.2 Mbps), WLAN ac mode 5 GHz (up to 433.3 Mbps) Special software used Scripts to start the throughput test and connect two of the EUTs to for testing each other were provided by the applicant and run on the auxiliary board computers. The main components of the EUT are listed and described in chapter 3.2 EUT Main components. TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCc Page 7 of 24

3.2 EUT MAIN COMPONENTS Sample Name Sample Code Description EUT 3E DE1015081ae01 Module on evaluation board Sample Parameter Value Serial No. 005 HW Version 01 SW Version P8.1 Comment Tested sample Integral Antenna None, two external 50 Ohm connectors on evaluation board. Antenna gain used for evaluation of test results: 2dBi. For the purpose of this test two devices were connected to each other by use of cables and couplers. Sample Name Sample Code Description EUT 3A DE1015081aa01 Module on evaluation board Sample Parameter Value Serial No. 001 HW Version 01 SW Version P8.1 Comment Sample used as companion device, not tested (outside of anechoic chamber for radiated measurements, additional 30 dB att. during conducted tests.) Integral Antenna None, two external 50 Ohm connectors on evaluation board. Antenna gain used for evaluation of test results: 2dBi. For the purpose of this test two devices were connected to each other by use of cables and couplers. NOTE:The short description is used to simplify the identification of the EUT in this test report. 3.3 ANCILLARY EQUIPMENT For the purposes of this test report, ancillary equipment is defined as equipment which is used in conjunction with the EUT to provide operational and control features to the EUT. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Ancillary Equipment can influence the test results. Device Details Description (Manufacturer, Type Model, OUT Code) Evaluation Board UBLOX, REV. B, - , - Board the EUT is mounted to, providing ports to the EUT (DC, Antennas, wired communication) TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCc Page 8 of 24

3.4 AUXILIARY EQUIPMENT For the purposes of this test report, auxiliary equipment is defined as equipment which is used temporarily to enable operational and control features especially used for the tests of the EUT which is not used during normal operation or equipment that is used during the tests in combination with the EUT but is not subject of this test report. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Auxiliary Equipment can influence the test results. Device Details Description (Manufacturer, HW, SW, S/N) Board Computer Toradex, Ixora, - , -, - Computer used for setting the test modes 3.5 EUT SETUPS This chapter describes the combination of EUTs and equipment used for testing. The rationale for selecting the EUTs, ancillary and auxiliary equipment and interconnecting cables, is to test a representative configuration meeting the requirements of the referenced standards. Setup Combination of EUTs Description and Rationale EUT 3E, Evaluation Setup for radiated and conducted tests S01_3_AE01 Board, Board Computer 3.6 OPERATING MODES This chapter describes the operating modes of the EUTs used for testing. 3.7 PRODUCT LABELLING 3.7.1 FCC ID LABEL Please refer to the documentation of the applicant. 3.7.2 LOCATION OF THE LABEL ON THE EUT Please refer to the documentation of the applicant. TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCc Page 9 of 24

4 TEST RESULTS 4.1 SIMULTANEOUS TRANSMISSION - SPURIOUS RADIATED EMISSIONS Standard FCC Part 15 Subpart C The test was performed according to: ANSI C63.10 4.1.1 TEST DESCRIPTION Standard FCC Part 15 Subpart C Radiated Emissions (with cable connection between two devices instead of antenna) The test was performed according to: ANSI C63.10 The test set-up was made in accordance to the general provisions of ANSI C63.10 in a typical installation configuration. The Equipment Under Test (EUT) was set up on a non-conductive table 1.0 x 2.0 m in the semi-anechoic chamber. The influence of the EUT support table that is used between 30–1000 MHz was evaluated. The measurement procedure is implemented into the EMI test software EMC32 from R&S. Exploratory tests are performed at 3 orthogonal axes to determine the worst-case orientation of a body-worn or handheld EUT. The final test on all kind of EUTs is also performed at 3 axes. A pre-check is performed while the EUT is powered from a DC power source. 1. Measurement above 1 GHi The following modifications apply to the measurement procedure for the frequency range above 1 GHz: Step 1: The Equipment Under Test (EUT) was set up on a non-conductive support (tilt device) at 1.5 m height in the fully-anechoic chamber. All steps were performed with one height (1.5 m) of the receiving antenna only. The EUT is turned during the preliminary measurement across the elevation axis, with a step size of 90 °. The turn table step size (azimuth angle) for the preliminary measurement is 45 °. Step 2: Due to the fact, that in this frequency range the test is performed in a fully anechoic room, the height scan of the receiving antenna instep 2 is omitted. Instead of this, a maximum search with a step size ± 45° for the elevation axis is performed. The turn table azimuth will slowly vary by ± 22.5°. The elevation angle will slowly vary by ± 45° EMI receiver settings (for all steps): - Detector: Peak, Average - IF Bandwidth = 1 MHz Step 3: Spectrum analyser settings for step 3: - Detector: Peak / Average - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 1 MHz - Measuring time: 1 s TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCc Page 10 of 24

Conducted Emissions at antenna ports (cable connection between two devices, companion device attenuated by 30 dB) The Equipment Under Test (EUT) was set up to perform the spurious emissions measurements. The EUT was connected to spectrum analyzer via a short coax cable with a known loss. A 4 to 1 port combiner was used to connect the 4 antenna ports of the EUT and its companion device to each other to allow simultaneous transmissions in normal mode with cable connection. Analyzer settings: • Frequency range: 1000 – 25000 MHz • Resolution Bandwidth (RBW): 1000 kHz • Video Bandwidth (VBW): 3000 kHz • Trace: Maxhold • Detector: Peak / Average The conducted emissions limit shown in the plot shows the restricted bands limit converted to dBm according to the description below, as well as, for information purposes only, the FCC15.407 limit of -27 dBm/MHz which is not applicable for the purpose of the simultaneous transmissions test. The measurement result already includes an antenna gain of 2 dBi. The Value measured in dBm can be converted to dB V/m as given in KDB 558074: 1. Measure the conducted output power in dBm. 2. Add the maximum antenna gain in dBi 3. Add the appropriate ground reflection factor 6 dB for frequencies ≤ 30 MHz; 4.7 dB for frequencies between 30 MHz and 1000 MHz, inclusive; and 0 dB for frequencies > 1000 MHz). 4. Convert the resultant EIRP level to an equivalent electric field strength level using the following relationship: E = EIRP – 20 log D + 104.8 Where E is the electric field strength in dB V/m, EIRP is the equivalent isotropically radiated power in dBm D is the specified measurement distance in m Value [dB V/m] = Measured value [dBm] + Maximum Antenna Gain [dBi] + Ground reflection factor – 20 log D + 104.8 The limit was converted accordingly: Limit [dBm] = Limit [dB V] + 20 log D – 104.8 (the antenna gain is added to the measured value and the Ground Reflection factor for > 1GHz is 0 thus both values are not considered in the formula) 4.1.2 TEST REQUIREMENTS / LIMITS FCC Part 15, Subpart C, §15.247 (d) ... In addition, radiated emissions which fall in the restricted bands, as defined in Section 15.205(a), must also comply with the radiated emission limits specified in Section 15.209(a) (see Section 15.205(c)). FCC Part 15, Subpart C, §15.209, Radiated Emission Limits TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCc Page 11 of 24

Measurement Frequency in MHz Limit ( V/m) Limits (dB V/m) distance (m) 0.009 – 0.49 2400/F(kHz)@300m 3 (48.5 – 13.8)@300m 0.49 – 1.705 24000/F(kHz)@30m 3 (33.8 – 23.0)@30m 1.705 – 30 30@30m 3 29.5@30m The measured values are corrected with an inverse linear distance extrapolation factor (40 dB/decade) according FCC 15.31 (2). Measurement Frequency in MHz Limit ( V/m) Limits (dB V/m) distance (m) 30 – 88 100@3m 3 40.0@3m 88 – 216 150@3m 3 43.5@3m 216 – 960 200@3m 3 46.0@3m 960 - 26000 500@3m 3 54.0@3m 26000 - 40000 500@3m 1 54.0@3m The measured values above 26 GHz are corrected with an inverse linear distance extrapolation factor (20 dB/decade). §15.35(b) ..., there is also a limit on the radio frequency emissions, as measured using instrumentation with a peak detector function, corresponding to 20 dB above the maximum permitted average limit.... Used conversion factor: Limit (dB V/m) = 20 log (Limit ( V/m)/1 V/m) 4.1.3 TEST PROTOCOL RADIATED EMISSIONS Ambient temperature: 24 °C Air Pressure: 1010 hPa Humidity: 30 % Remark: Please see next sub-clause for the measurement plot. TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCc Page 12 of 24

4.1.4 MEASUREMENT PLOT RADIATED EMISSIONS Active Transmitters = BT hopping, WLAN 2.4 GHz on 2442 MHZ, WLAN 5GHz on 5210 MHz (S01_3_AE01) 90 2.440677000 GHz 80 84.441 dBµV/m 5.203555556 GHz 77.843 dBµV/m 70 FCC_15.407_PEAK_SUB1&2A 60 Level in dBµV/m FCC_15.407_AV 50 40 30 20 10 1G 2G 3G 4G 5G 6 8 10G 20G 26G Frequency in Hz Critical_Freqs Frequency MaxPeak Average Limit Margi Meas. Bandwidt Heigh Pol Azimut Elevatio (MHz) (dBµV/m) (dBµV/m) (dBµV/m) n Time h t h n (dB) (ms) (kHz) (cm) (deg) (deg) 1244.950000 60.35 --- 68.20 7.85 --- --- 150.0 V -87.0 -15.0 1264.300000 54.44 --- 68.20 13.76 --- --- 150.0 V -86.0 7.0 1493.982000 --- 34.93 54.00 19.07 --- --- 150.0 V -89.0 6.0 1494.173500 55.04 --- 74.00 18.96 --- --- 150.0 V -89.0 -2.0 3733.200000 61.55 --- 74.00 12.45 --- --- 150.0 H 100.0 -15.0 3744.600000 --- 33.33 54.00 20.67 --- --- 150.0 V 91.0 15.0 Final_Result Frequency MaxPeak CAverage Limit Margi Meas. Bandwidt Heigh Pol Azimut Elevatio (MHz) (dBµV/m) (dBµV/m) (dBµV/m) n Time h t h n (dB) (ms) (kHz) (cm) (deg) (deg) 1244.950000 59.94 --- 68.20 8.26 1000.0 1000.000 150.0 V -87.0 -15.0 1264.300000 54.33 --- 68.20 13.87 1000.0 1000.000 150.0 V -86.0 7.0 1493.982000 --- 32.88 54.00 21.12 1000.0 1000.000 150.0 V -89.0 6.0 1494.173500 53.91 --- 74.00 20.09 1000.0 1000.000 150.0 V -89.0 -2.0 3733.200000 68.34 --- 74.00 5.66 1000.0 1000.000 150.0 H 101.0 -15.0 3744.600000 --- 36.01 54.00 17.99 1000.0 1000.000 150.0 V 91.0 15.0 TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCc Page 13 of 24

4.1.5 TEST PROTOCOL CONDUCTED EMISSIONS Ambient temperature: 23 °C Air Pressure: 1003 hPa Humidity: 34 % Remark: Please see next sub-clause for the measurement plot. 4.1.6 MEASUREMENT PLOT CONDUCTED EMISSIONS 20 10 0 -10 Level in dBm -20 FCC_15.407_PEAK_SUB1&2A_dBm -30 -40 FCC_15.407_AV_1GHz-40GHz_dBm -50 -60 1G 2G 3G 4G 5G 6 8 10G 20G 26G Frequency in Hz Note: The -27 dBm limit breached by the 2.4 GHz band transmitters is not applicable for this test. 4.1.7 TEST EQUIPMENT USED - Radiated Emissions - R&S TS8997 TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCc Page 14 of 24

5 TEST EQUIPMENT 1 R&S TS8997 EN300328/301893 Test Lab Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 1.1 MFS Rubidium Datum-Beverly 5489/001 2017-07 2018-07 Frequency Standard 1.2 1515 / 93459 Broadband Weinschel LN673 Power Divider Associates SMA (Aux) 1.3 FSV30 Signal Rohde & Schwarz 103005 2016-02 2018-02 Analyzer 10 Hz - 30 GHz 1.4 Fluke 177 Digital Fluke Europe B.V. 86670383 2016-02 2018-02 Multimeter 03 (Multimeter) 1.5 A8455-4 4 Way Power - Divider (SMA) 1.6 Opus10 THI ThermoHygro Lufft Mess- und 7482 2017-03 2019-03 (8152.00) Datalogger 03 Regeltechnik GmbH (Environ) 1.7 SMBV100A Vector Signal Rohde & Schwarz 259291 2016-10 2019-10 Generator 9 kHz - 6 GHz 1.8 OSP120 Switching Unit Rohde & Schwarz 101158 2016-11 2018-11 with integrated power meter 2 Radiated Emissions Lab to perform radiated emission tests Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 2.1 NRV-Z1 Sensor Head A Rohde & Schwarz 827753/005 2017-05 2018-05 2.2 MFS Rubidium Datum GmbH 002 2017-10 2018-10 Frequency Normal MFS 2.3 Opus10 TPR ThermoAirpres Lufft Mess- und 13936 2017-04 2019-04 (8253.00) sure Regeltechnik GmbH Datalogger 13 (Environ) 2.4 Anechoic 10.58 x 6.38 x Frankonia none 2016-05 2019-05 Chamber 6.00 m 2.5 HL 562 Ultralog new Rohde & Schwarz 830547/003 2015-06 2018-06 biconicals 2.6 5HC2700/12750 High Pass Trilithic 9942012 -1.5-KK Filter 2.7 ASP 1.2/1.8-10 Antenna Mast Maturo GmbH - kg 2.8 Fully Anechoic 8.80m x Albatross Projects P26971-647-001- 2015-06 2018-06 Room 4.60m x PRB 4.05m (l x w x h) 2.9 Fluke 177 Digital Fluke Europe B.V. 86670383 2016-02 2018-02 Multimeter 03 (Multimeter) TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCc Page 15 of 24

Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 2.10 JS4-18002600- Broadband Miteq 849785 32-5P Amplifier 18 GHz - 26 GHz 2.11 FSW 43 Spectrum Rohde & Schwarz 103779 2016-12 2018-12 Analyzer 2.12 3160-09 Standard Gain EMCO Elektronic 00083069 / Pyramidal GmbH Horn Antenna 26.5 GHz 2.13 WHKX 7.0/18G- High Pass Wainwright 09 8SS Filter 2.14 4HC1600/12750 High Pass Trilithic 9942011 -1.5-KK Filter 2.15 Chroma 6404 AC Power Chroma ATE INC. 64040001304 Source 2.16 JS4-00102600- Broadband Miteq 619368 42-5A Amplifier 30 MHz - 26 GHz 2.17 TT 1.5 WI Turn Table Maturo GmbH - 2.18 HL 562 Ultralog Log.-per. Rohde & Schwarz 100609 2016-04 2019-04 Antenna 2.19 3160-10 Standard Gain EMCO Elektronic 00086675 / Pyramidal GmbH Horn Antenna 40 GHz 2.20 5HC3500/18000 High Pass Trilithic 200035008 -1.2-KK Filter 2.21 HFH2-Z2 Loop Antenna Rohde & Schwarz 829324/006 2018-01 2021-01 2.22 Opus10 THI ThermoHygro Lufft Mess- und 12482 2017-03 2019-03 (8152.00) Datalogger 12 Regeltechnik GmbH (Environ) 2.23 ESR 7 EMI Receiver / Rohde & Schwarz 101424 2016-11 2018-11 Spectrum Analyzer 2.24 JS4-00101800- Broadband Miteq 896037 35-5P Amplifier 30 MHz - 18 GHz 2.25 AS 620 P Antenna mast HD GmbH 620/37 2.26 Tilt device Antrieb TD1.5- Maturo GmbH TD1.5- Maturo 10kg 10kg/024/37907 (Rohacell) 09 2.27 FS-Z90 Harmonic Rohde & Schwarz 101686 2017-03 2020-03 Mixer 60 - 90 Memmingen GHz 2.28 ESIB 26 Spectrum Rohde & Schwarz 830482/004 2018-01 2020-01 Analyzer 2.29 PAS 2.5 - 10 kg Antenna Mast Maturo GmbH - 2.30 AM 4.0 Antenna mast Maturo GmbH AM4.0/180/1192 0513 2.31 HF 907 Double-ridged Rohde & Schwarz 102444 2015-05 2018-05 horn The calibration interval is the time interval between “Last Calibration” and “Calibration Due” TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCc Page 16 of 24

6 ANTENNA FACTORS, CABLE LOSS AND SAMPLE CALCULATIONS This chapter contains the antenna factors with their corresponding path loss of the used measurement path for all antennas as well as the insertion loss of the LISN. 6.1 LISN R&S ESH3-Z5 (150 KHZ – 30 MHZ) cable LISN loss insertion (incl. 10 loss dB ESH3- atten- Frequency Corr. Z5 uator) MHz dB dB dB 0.15 10.1 0.1 10.0 5 10.3 0.1 10.2 7 10.5 0.2 10.3 10 10.5 0.2 10.3 12 10.7 0.3 10.4 14 10.7 0.3 10.4 16 10.8 0.4 10.4 18 10.9 0.4 10.5 20 10.9 0.4 10.5 22 11.1 0.5 10.6 24 11.1 0.5 10.6 26 11.2 0.5 10.7 28 11.2 0.5 10.7 30 11.3 0.5 10.8 Sample calculation ULISN (dB V) = U (dB V) + Corr. (dB) U = Receiver reading LISN Insertion loss = Voltage Division Factor of LISN Corr. = sum of single correction factors of used LISN, cables, switch units (if used) Linear interpolation will be used for frequencies in between the values in the table. TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCc Page 17 of 24

6.2 ANTENNA R&S HFH2-Z2 (9 KHZ – 30 MHZ) cable cable cable cable distance dLimit dused loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. AF (inside (outside (switch (to (-40 dB/ distance distance Frequency HFH-Z2) Corr. chamber) chamber) unit) receiver) decade) (limit) (used) MHz dB (1/m) dB dB dB dB dB dB m m 0.009 20.50 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.01 20.45 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.015 20.37 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.02 20.36 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.025 20.38 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.03 20.32 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.05 20.35 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.08 20.30 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.1 20.20 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.2 20.17 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.3 20.14 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.49 20.12 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.490001 20.12 -39.6 0.1 0.1 0.1 0.1 -40 30 3 0.5 20.11 -39.6 0.1 0.1 0.1 0.1 -40 30 3 0.8 20.10 -39.6 0.1 0.1 0.1 0.1 -40 30 3 1 20.09 -39.6 0.1 0.1 0.1 0.1 -40 30 3 2 20.08 -39.6 0.1 0.1 0.1 0.1 -40 30 3 3 20.06 -39.6 0.1 0.1 0.1 0.1 -40 30 3 4 20.05 -39.5 0.2 0.1 0.1 0.1 -40 30 3 5 20.05 -39.5 0.2 0.1 0.1 0.1 -40 30 3 6 20.02 -39.5 0.2 0.1 0.1 0.1 -40 30 3 8 19.95 -39.5 0.2 0.1 0.1 0.1 -40 30 3 10 19.83 -39.4 0.2 0.1 0.2 0.1 -40 30 3 12 19.71 -39.4 0.2 0.1 0.2 0.1 -40 30 3 14 19.54 -39.4 0.2 0.1 0.2 0.1 -40 30 3 16 19.53 -39.3 0.3 0.1 0.2 0.1 -40 30 3 18 19.50 -39.3 0.3 0.1 0.2 0.1 -40 30 3 20 19.57 -39.3 0.3 0.1 0.2 0.1 -40 30 3 22 19.61 -39.3 0.3 0.1 0.2 0.1 -40 30 3 24 19.61 -39.3 0.3 0.1 0.2 0.1 -40 30 3 26 19.54 -39.3 0.3 0.1 0.2 0.1 -40 30 3 28 19.46 -39.2 0.3 0.1 0.3 0.1 -40 30 3 30 19.73 -39.1 0.4 0.1 0.3 0.1 -40 30 3 Sample calculation E (dB V/m) = U (dB V) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) distance correction = -40 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCc Page 18 of 24

6.3 ANTENNA R&S HL562 (30 MHZ – 1 GHZ) (dLimit = 3 m) cable cable cable cable distance dLimit dused AF loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. R&S (inside (outside (switch (to (-20 dB/ distance distance Frequency HL562 Corr. chamber) chamber) unit) receiver) decade) (limit) (used) MHz dB (1/m) dB dB dB dB dB dB m m 30 18.6 0.6 0.29 0.04 0.23 0.02 0.0 3 3 50 6.0 0.9 0.39 0.09 0.32 0.08 0.0 3 3 100 9.7 1.2 0.56 0.14 0.47 0.08 0.0 3 3 150 7.9 1.6 0.73 0.20 0.59 0.12 0.0 3 3 200 7.6 1.9 0.84 0.21 0.70 0.11 0.0 3 3 250 9.5 2.1 0.98 0.24 0.80 0.13 0.0 3 3 300 11.0 2.3 1.04 0.26 0.89 0.15 0.0 3 3 350 12.4 2.6 1.18 0.31 0.96 0.13 0.0 3 3 400 13.6 2.9 1.28 0.35 1.03 0.19 0.0 3 3 450 14.7 3.1 1.39 0.38 1.11 0.22 0.0 3 3 500 15.6 3.2 1.44 0.39 1.20 0.19 0.0 3 3 550 16.3 3.5 1.55 0.46 1.24 0.23 0.0 3 3 600 17.2 3.5 1.59 0.43 1.29 0.23 0.0 3 3 650 18.1 3.6 1.67 0.34 1.35 0.22 0.0 3 3 700 18.5 3.6 1.67 0.42 1.41 0.15 0.0 3 3 750 19.1 4.1 1.87 0.54 1.46 0.25 0.0 3 3 800 19.6 4.1 1.90 0.46 1.51 0.25 0.0 3 3 850 20.1 4.4 1.99 0.60 1.56 0.27 0.0 3 3 900 20.8 4.7 2.14 0.60 1.63 0.29 0.0 3 3 950 21.1 4.8 2.22 0.60 1.66 0.33 0.0 3 3 1000 21.6 4.9 2.23 0.61 1.71 0.30 0.0 3 3 (dLimit = 10 m) 30 18.6 -9.9 0.29 0.04 0.23 0.02 -10.5 10 3 50 6.0 -9.6 0.39 0.09 0.32 0.08 -10.5 10 3 100 9.7 -9.2 0.56 0.14 0.47 0.08 -10.5 10 3 150 7.9 -8.8 0.73 0.20 0.59 0.12 -10.5 10 3 200 7.6 -8.6 0.84 0.21 0.70 0.11 -10.5 10 3 250 9.5 -8.3 0.98 0.24 0.80 0.13 -10.5 10 3 300 11.0 -8.1 1.04 0.26 0.89 0.15 -10.5 10 3 350 12.4 -7.9 1.18 0.31 0.96 0.13 -10.5 10 3 400 13.6 -7.6 1.28 0.35 1.03 0.19 -10.5 10 3 450 14.7 -7.4 1.39 0.38 1.11 0.22 -10.5 10 3 500 15.6 -7.2 1.44 0.39 1.20 0.19 -10.5 10 3 550 16.3 -7.0 1.55 0.46 1.24 0.23 -10.5 10 3 600 17.2 -6.9 1.59 0.43 1.29 0.23 -10.5 10 3 650 18.1 -6.9 1.67 0.34 1.35 0.22 -10.5 10 3 700 18.5 -6.8 1.67 0.42 1.41 0.15 -10.5 10 3 750 19.1 -6.3 1.87 0.54 1.46 0.25 -10.5 10 3 800 19.6 -6.3 1.90 0.46 1.51 0.25 -10.5 10 3 850 20.1 -6.0 1.99 0.60 1.56 0.27 -10.5 10 3 900 20.8 -5.8 2.14 0.60 1.63 0.29 -10.5 10 3 950 21.1 -5.6 2.22 0.60 1.66 0.33 -10.5 10 3 1000 21.6 -5.6 2.23 0.61 1.71 0.30 -10.5 10 3 Sample calculation E (dB V/m) = U (dB V) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) distance correction = -20 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Tables show an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCc Page 19 of 24

6.4 ANTENNA R&S HF907 (1 GHZ – 18 GHZ) cable cable loss 3 loss 1 (switch (relay + cable unit, AF cable loss 2 atten- cable R&S inside (outside uator & loss 4 (to Frequency HF907 Corr. chamber) chamber) pre-amp) receiver) MHz dB (1/m) dB dB dB dB dB 1000 24.4 -19.4 0.99 0.31 -21.51 0.79 2000 28.5 -17.4 1.44 0.44 -20.63 1.38 3000 31.0 -16.1 1.87 0.53 -19.85 1.33 4000 33.1 -14.7 2.41 0.67 -19.13 1.31 5000 34.4 -13.7 2.78 0.86 -18.71 1.40 6000 34.7 -12.7 2.74 0.90 -17.83 1.47 7000 35.6 -11.0 2.82 0.86 -16.19 1.46 cable loss 4 cable (switch loss 1 cable cable unit, used AF (relay loss 2 loss 3 atten- cable for R&S inside (inside (outside uator & loss 5 (to FCC Frequency HF907 Corr. chamber) chamber) chamber) pre-amp) receiver) 15.247 MHz dB (1/m) dB dB dB dB dB dB 3000 31.0 -23.4 0.47 1.87 0.53 -27.58 1.33 4000 33.1 -23.3 0.56 2.41 0.67 -28.23 1.31 5000 34.4 -21.7 0.61 2.78 0.86 -27.35 1.40 6000 34.7 -21.2 0.58 2.74 0.90 -26.89 1.47 7000 35.6 -19.8 0.66 2.82 0.86 -25.58 1.46 cable loss 1 cable cable cable cable cable AF (relay loss 2 loss 3 loss 4 loss 5 loss 6 R&S inside (High (pre- (inside (outside (to Frequency HF907 Corr. chamber) Pass) amp) chamber) chamber) receiver) MHz dB (1/m) dB dB dB dB dB dB dB 7000 35.6 -57.3 0.56 1.28 -62.72 2.66 0.94 1.46 8000 36.3 -56.3 0.69 0.71 -61.49 2.84 1.00 1.53 9000 37.1 -55.3 0.68 0.65 -60.80 3.06 1.09 1.60 10000 37.5 -56.2 0.70 0.54 -61.91 3.28 1.20 1.67 11000 37.5 -55.3 0.80 0.61 -61.40 3.43 1.27 1.70 12000 37.6 -53.7 0.84 0.42 -59.70 3.53 1.26 1.73 13000 38.2 -53.5 0.83 0.44 -59.81 3.75 1.32 1.83 14000 39.9 -56.3 0.91 0.53 -63.03 3.91 1.40 1.77 15000 40.9 -54.1 0.98 0.54 -61.05 4.02 1.44 1.83 16000 41.3 -54.1 1.23 0.49 -61.51 4.17 1.51 1.85 17000 42.8 -54.4 1.36 0.76 -62.36 4.34 1.53 2.00 18000 44.2 -54.7 1.70 0.53 -62.88 4.41 1.55 1.91 Sample calculation E (dB V/m) = U (dB V) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. Tables show an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCc Page 20 of 24

6.5 ANTENNA EMCO 3160-09 (18 GHZ – 26.5 GHZ) cable cable cable cable cable AF loss 1 loss 2 loss 3 loss 4 loss 5 EMCO (inside (pre- (inside (switch (to Frequency 3160-09 Corr. chamber) amp) chamber) unit) receiver) MHz dB (1/m) dB dB dB dB dB dB 18000 40.2 -23.5 0.72 -35.85 6.20 2.81 2.65 18500 40.2 -23.2 0.69 -35.71 6.46 2.76 2.59 19000 40.2 -22.0 0.76 -35.44 6.69 3.15 2.79 19500 40.3 -21.3 0.74 -35.07 7.04 3.11 2.91 20000 40.3 -20.3 0.72 -34.49 7.30 3.07 3.05 20500 40.3 -19.9 0.78 -34.46 7.48 3.12 3.15 21000 40.3 -19.1 0.87 -34.07 7.61 3.20 3.33 21500 40.3 -19.1 0.90 -33.96 7.47 3.28 3.19 22000 40.3 -18.7 0.89 -33.57 7.34 3.35 3.28 22500 40.4 -19.0 0.87 -33.66 7.06 3.75 2.94 23000 40.4 -19.5 0.88 -33.75 6.92 3.77 2.70 23500 40.4 -19.3 0.90 -33.35 6.99 3.52 2.66 24000 40.4 -19.8 0.88 -33.99 6.88 3.88 2.58 24500 40.4 -19.5 0.91 -33.89 7.01 3.93 2.51 25000 40.4 -19.3 0.88 -33.00 6.72 3.96 2.14 25500 40.5 -20.4 0.89 -34.07 6.90 3.66 2.22 26000 40.5 -21.3 0.86 -35.11 7.02 3.69 2.28 26500 40.5 -21.1 0.90 -35.20 7.15 3.91 2.36 Sample calculation E (dB V/m) = U (dB V) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCc Page 21 of 24

6.6 ANTENNA EMCO 3160-10 (26.5 GHZ – 40 GHZ) cable cable cable cable distance dLimit dused AF loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. EMCO (inside (outside (switch (to (-20 dB/ distance distance Frequency 3160-10 Corr. chamber) chamber) unit) receiver) decade) (limit) (used) GHz dB (1/m) dB dB dB dB dB dB m m 26.5 43.4 -11.2 4.4 -15.6 3 0.5 27.0 43.4 -11.2 4.4 -15.6 3 0.5 28.0 43.4 -11.1 4.5 -15.6 3 0.5 29.0 43.5 -11.0 4.6 -15.6 3 0.5 30.0 43.5 -10.9 4.7 -15.6 3 0.5 31.0 43.5 -10.8 4.7 -15.6 3 0.5 32.0 43.5 -10.7 4.8 -15.6 3 0.5 33.0 43.6 -10.7 4.9 -15.6 3 0.5 34.0 43.6 -10.6 5.0 -15.6 3 0.5 35.0 43.6 -10.5 5.1 -15.6 3 0.5 36.0 43.6 -10.4 5.1 -15.6 3 0.5 37.0 43.7 -10.3 5.2 -15.6 3 0.5 38.0 43.7 -10.2 5.3 -15.6 3 0.5 39.0 43.7 -10.2 5.4 -15.6 3 0.5 40.0 43.8 -10.1 5.5 -15.6 3 0.5 Sample calculation E (dB V/m) = U (dB V) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. distance correction = -20 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCc Page 22 of 24

7 SETUP DRAWINGS Drawing 1: Setup in the Anechoic chamber. For measurements below 1 GHz the ground was replaced by a conducting groundplane. Shielded Shielded RF cable RF cable OUT Rubidium Spectrum (object Frequency 4 to 1 Analyser under test) Standard coupler 30 dB att. Companion device 30 dB att. Drawing 2: Setup for conducted radio tests. TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCc Page 23 of 24

8 MEASUREMENT UNCERTAINTIES Test Case Parameter Uncertainty AC Power Line Power ± 3.4 dB Field Strength of spurious radiation Power ± 5.5 dB 6 dB / 26 dB / 99% Bandwidth Power ± 2.9 dB Frequency ± 11.2 kHz Conducted Output Power Power ± 2.2 dB Band Edge Compliance Power ± 2.2 dB Frequency ± 11.2 kHz Frequency Stability Frequency ± 25 Hz Power Spectral Density Power ± 2.2 dB 9 PHOTO REPORT Please see separate photo report. TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCc Page 24 of 24


Document Created: 2018-05-18 16:32:43
Document Modified: 2018-05-18 16:32:43
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC