Test Report part 4

FCC ID: XPYJODYW164-07A

Test Report

Download: PDF
FCCID_4035054

4.8 BAND EDGE Standard FCC Part 15 Subpart E 4.8.1 RADIATED MEASUREMENTS (ANTENNA PORTS TERMINATED WITH 50 OHM) The test was performed according to: ANSI C63.10 4.8.1.1 Test Description Please see test description for the test case “UNDESIRABLE EMISSIONS” 4.8.1.2 Test Requirements / Limits For band edges connected to a restricted band, the limits are specified in Section 15.209(a) FCC Part 15, Subpart C, §15.209, Radiated Emission Limits Measurement Frequency in MHz Limit ( V/m) Limits (dB V/m) distance (m) 0.009 – 0.49 2400/F(kHz)@300m 3 (48.5 – 13.8)@300m 0.49 – 1.705 24000/F(kHz)@30m 3 (33.8 – 23.0)@30m 1.705 – 30 30@30m 3 29.5@30m The measured values are corrected with an inverse linear distance extrapolation factor (40 dB/decade) according FCC 15.31 (2). Measurement Frequency in MHz Limit ( V/m) Limits (dB V/m) distance (m) 30 – 88 100@3m 3 40.0@3m 88 – 216 150@3m 3 43.5@3m 216 – 960 200@3m 3 46.0@3m 960 - 26000 500@3m 3 54.0@3m 26000 - 40000 500@3m 1 54.0@3m The measured values above 26 GHz are corrected with an inverse linear distance extrapolation factor (20 dB/decade). §15.35(b) ..., there is also a limit on the radio frequency emissions, as measured using instrumentation with a peak detector function, corresponding to 20 dB above the maximum permitted average limit.... Used conversion factor: Limit (dB V/m) = 20 log (Limit ( V/m)/1 V/m) TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 67 of 94

4.8.1.3 Test Protocol Ambient temperature: 22 - 23 °C Air Pressure: 1012 - 1019 hPa Humidity: 36 - 37 % Core 0 WLAN a-Mode; 20 MHz; 6 Mbit/s Applied duty cycle correction (AV): 0 dB U-NII- Ch. Ch. Band Spurious Detec- RBW Limit Margin Limit FCC Subband No. Center Edge Level tor [kHi] [dB V/m] [dB] Type /IC? Freq. Freq. [dB V/m] [MHi] [MHi] 1 36 5180 5150.0 59.2 PEAK 1000 74.0 14.8 BE-RB FCC&IC 36 5180 5150.0 46.4 AV 1000 54.0 7.6 BE-RB FCC&IC 2A 64 5320 5350.0 60.0 PEAK 1000 74.0 14.0 BE-RB FCC&IC 64 5320 5350.0 46.6 AV 1000 54.0 7.4 BE-RB FCC&IC 2C 100 5500 5460.0 60.7 PEAK 1000 74.0 13.3 BE-RB FCC&IC 100 5500 5460.0 47.0 AV 1000 54.0 7.0 BE-RB FCC&IC 100 5500 5470.0 59.9 PEAK 1000 68.0 8.1 BE-UE FCC&IC 140 5700 5725.0 60.0 PEAK 1000 68.0 8.0 BE-UE FCC&IC 3 149 5745 5725.0 65.2 PEAK 1000 78.0 12.8 BE-UE FCC&IC 165 5825 5850.0 61.0 PEAK 1000 78.0 17.0 BE-UE FCC&IC WLAN n-Mode; 20 MHz; MCS0 Applied duty cycle correction (AV): 0 dB U-NII- Ch. Ch. Band Spurious Detec- RBW Limit Margin Limit FCC Subband No. Center Edge Level tor [kHi] [dB V/m] [dB] Type /IC? Freq. Freq. [dB V/m] [MHi] [MHi] 1 36 5180 5150.0 58.9 PEAK 1000 74.0 15.1 BE-RB FCC&IC 36 5180 5150.0 46.3 AV 1000 54.0 7.7 BE-RB FCC&IC 2A 64 5320 5350.0 59.7 PEAK 1000 74.0 14.3 BE-RB FCC&IC 64 5320 5350.0 46.8 AV 1000 54.0 7.2 BE-RB FCC&IC 2C 100 5500 5460.0 60.1 PEAK 1000 74.0 13.9 BE-RB FCC&IC 100 5500 5460.0 46.9 AV 1000 54.0 7.1 BE-RB FCC&IC 100 5500 5470.0 59.4 PEAK 1000 68.0 8.6 BE-UE FCC&IC 140 5700 5725.0 59.9 PEAK 1000 68.0 8.1 BE-UE FCC&IC 3 149 5745 5725.0 65.1 PEAK 1000 78.0 12.9 BE-UE FCC&IC 165 5825 5850.0 60.6 PEAK 1000 78.0 17.4 BE-UE FCC&IC WLAN n-Mode; 40 MHz; MCS 0 Applied duty cycle correction (AV): 0 dB U-NII- Ch. Ch. Band Spurious Detec- RBW Limit Margin Limit FCC Subband No. Center Edge Level tor [kHi] [dB V/m] [dB] Type /IC? Freq. Freq. [dB V/m] [MHi] [MHi] 1 38 5190 5150.0 59.5 PEAK 1000 74.0 14.5 BE-RB FCC&IC 38 5190 5150.0 46.2 AV 1000 54.0 7.8 BE-RB FCC&IC 2A 62 5310 5350.0 57.7 PEAK 1000 74.0 16.3 BE-RB FCC&IC 62 5310 5350.0 44.3 AV 1000 54.0 9.7 BE-RB FCC&IC 2C 102 5510 5460.0 58.0 PEAK 1000 74.0 16.0 BE-RB FCC&IC 102 5510 5460.0 44.9 AV 1000 54.0 9.1 BE-RB FCC&IC 102 5510 5470.0 56.0 PEAK 1000 68.0 12.0 BE-UE FCC&IC 134 5670 5725.0 59.7 PEAK 1000 68.0 8.3 BE-UE FCC&IC 3 151 5755 5725.0 68.1 PEAK 1000 78.0 9.9 BE-UE FCC&IC 159 5795 5850.0 60.2 PEAK 1000 78.0 17.8 BE-UE FCC&IC TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 68 of 94

WLAN ac-Mode; 80 MHz; MCS 0 Applied duty cycle correction (AV): 0 dB U-NII- Ch. Ch. Band Spurious Detec- RBW Limit Margin Limit FCC Subband No. Center Edge Level tor [kHi] [dB V/m] [dB] Type /IC? Freq. Freq. [dB V/m] [MHi] [MHi] 1 42 5210 5150.0 58.5 PEAK 1000 74.0 15.5 BE-RB FCC&IC 42 5210 5150.0 46.3 AV 1000 54.0 7.7 BE-RB FCC&IC 2A 58 5290 5350.0 59.1 PEAK 1000 74.0 14.9 BE-RB FCC&IC 58 5290 5350.0 46.7 AV 1000 54.0 7.3 BE-RB FCC&IC 2C 106 5530 5460.0 60.0 PEAK 1000 74.0 14.0 BE-RB FCC&IC 106 5530 5460.0 47.0 AV 1000 54.0 7.0 BE-RB FCC&IC 106 5530 5470.0 59.9 PEAK 1000 68.0 8.1 BE-UE FCC&IC 3 155 5775 5725.0 64.4 PEAK 1000 78.0 13.6 BE-UE FCC&IC 155 5775 5850.0 61.4 PEAK 1000 78.0 16.6 BE-UE FCC&IC Core 1 WLAN a-Mode; 20 MHz; 6 Mbit/s Applied duty cycle correction (AV): 0 dB U-NII- Ch. Ch. Band Spurious Detec- RBW Limit Margin Limit FCC Subband No. Center Edge Level tor [kHi] [dB V/m] [dB] Type /IC? Freq. Freq. [dB V/m] [MHi] [MHi] 1 36 5180 5150.0 59.5 PEAK 1000 74.0 14.5 BE-RB FCC&IC 36 5180 5150.0 46.1 AV 1000 54.0 7.9 BE-RB FCC&IC 2A 64 5320 5350.0 59.8 PEAK 1000 74.0 14.2 BE-RB FCC&IC 64 5320 5350.0 46.7 AV 1000 54.0 7.3 BE-RB FCC&IC 2C 100 5500 5460.0 59.4 PEAK 1000 74.0 14.6 BE-RB FCC&IC 100 5500 5460.0 46.9 AV 1000 54.0 7.1 BE-RB FCC&IC 100 5500 5470.0 59.7 PEAK 1000 68.0 8.3 BE-UE FCC&IC 140 5700 5725.0 60.0 PEAK 1000 68.0 8.0 BE-UE FCC&IC 3 149 5745 5725.0 60.0 PEAK 1000 78.0 18.0 BE-UE FCC&IC 165 5825 5850.0 60.6 PEAK 1000 78.0 17.4 BE-UE FCC&IC WLAN n-Mode; 20 MHz; MCS0 Applied duty cycle correction (AV): 0 dB U-NII- Ch. Ch. Band Spurious Detec- RBW Limit Margin Limit FCC Subband No. Center Edge Level tor [kHi] [dB V/m] [dB] Type /IC? Freq. Freq. [dB V/m] [MHi] [MHi] 1 36 5180 5150.0 59.6 PEAK 1000 74.0 14.4 BE-RB FCC&IC 36 5180 5150.0 46.4 AV 1000 54.0 7.6 BE-RB FCC&IC 2A 64 5320 5350.0 59.5 PEAK 1000 74.0 14.5 BE-RB FCC&IC 64 5320 5350.0 46.7 AV 1000 54.0 7.3 BE-RB FCC&IC 2C 100 5500 5460.0 60.4 PEAK 1000 74.0 13.6 BE-RB FCC&IC 100 5500 5460.0 47.1 AV 1000 54.0 6.9 BE-RB FCC&IC 100 5500 5470.0 61.1 PEAK 1000 68.0 6.9 BE-UE FCC&IC 140 5700 5725.0 60.2 PEAK 1000 68.0 7.8 BE-UE FCC&IC 3 149 5745 5725.0 60.3 PEAK 1000 78.0 17.7 BE-UE FCC&IC 165 5825 5850.0 61.2 PEAK 1000 78.0 16.8 BE-UE FCC&IC TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 69 of 94

WLAN n-Mode; 40 MHz; MCS 0 Applied duty cycle correction (AV): 0 dB U-NII- Ch. Ch. Band Spurious Detec- RBW Limit Margin Limit FCC Subband No. Center Edge Level tor [kHi] [dB V/m] [dB] Type /IC? Freq. Freq. [dB V/m] [MHi] [MHi] 1 38 5190 5150.0 59.5 PEAK 1000 74.0 14.5 BE-RB FCC&IC 38 5190 5150.0 46.3 AV 1000 54.0 7.7 BE-RB FCC&IC 2A 62 5310 5350.0 59.9 PEAK 1000 74.0 14.1 BE-RB FCC&IC 62 5310 5350.0 46.6 AV 1000 54.0 7.4 BE-RB FCC&IC 2C 102 5510 5460.0 59.8 PEAK 1000 74.0 14.2 BE-RB FCC&IC 102 5510 5460.0 47.1 AV 1000 54.0 6.9 BE-RB FCC&IC 102 5510 5470.0 60.3 PEAK 1000 68.0 7.7 BE-UE FCC&IC 134 5670 5725.0 60.5 PEAK 1000 68.0 7.5 BE-UE FCC&IC 3 151 5755 5725.0 63.2 PEAK 1000 78.0 14.8 BE-UE FCC&IC 159 5795 5850.0 57.1 PEAK 1000 78.0 20.9 BE-UE FCC&IC WLAN ac-Mode; 80 MHz; MCS 0 Applied duty cycle correction (AV): 0 dB U-NII- Ch. Ch. Band Spurious Detec- RBW Limit Margin Limit FCC Subband No. Center Edge Level tor [kHi] [dB V/m] [dB] Type /IC? Freq. Freq. [dB V/m] [MHi] [MHi] 1 42 5210 5150.0 59.3 PEAK 1000 74.0 14.7 BE-RB FCC&IC 42 5210 5150.0 46.2 AV 1000 54.0 7.8 BE-RB FCC&IC 2A 58 5290 5350.0 59.7 PEAK 1000 74.0 14.3 BE-RB FCC&IC 58 5290 5350.0 46.6 AV 1000 54.0 7.4 BE-RB FCC&IC 2C 106 5530 5460.0 60.5 PEAK 1000 74.0 13.5 BE-RB FCC&IC 106 5530 5460.0 47.0 AV 1000 54.0 7.0 BE-RB FCC&IC 106 5530 5470.0 59.8 PEAK 1000 68.0 8.2 BE-UE FCC&IC 3 155 5775 5725.0 60.4 PEAK 1000 78.0 17.6 BE-UE FCC&IC 155 5775 5850.0 61.4 PEAK 1000 78.0 16.6 BE-UE FCC&IC Remark: Please see next sub-clause for the measurement plot. TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 70 of 94

4.8.1.4 Measurement Plot (showing the highest value, “worst case”) Radio Technology = WLAN a 20 MHz, Channel 100, Core 0 (S01_3_AB01) 80 70 FCC_15.407_PEAK_SUB2C 60 FCC_15.407_AV 50 Level in dBµV/m 40 30 20 10 0 5455 5456 5458 5460 5462 5464 5466 5468 5470 Frequency in MHz Critical_Freqs Frequency MaxPeak Average Limit Margi Meas. Bandwidt Heigh Pol Azimut Elevatio (MHz) (dBµV/m) (dBµV/m) (dBµV/m) n Time h t h n (dB) (ms) (kHz) (cm) (deg) (deg) 5459.890000 56.84 --- 74.00 17.16 --- --- 150.0 V 2.0 -9.0 5459.890000 --- 44.86 54.00 9.14 --- --- 150.0 H -98.0 15.2 5468.400000 57.68 --- 68.20 10.52 --- --- 150.0 H 128.0 82.4 Final_Result Frequency MaxPeak CAverage Limit Margi Meas. Bandwidt Heigh Pol Azimut Elevatio (MHz) (dBµV/m) (dBµV/m) (dBµV/m) n Time h t h n (dB) (ms) (kHz) (cm) (deg) (deg) 5459.890000 60.73 --- 74.00 13.27 1000.0 1000.000 150.0 V 2.0 -9.1 5459.890000 --- 47.00 54.00 7.00 1000.0 1000.000 150.0 H -98.0 15.2 5468.400000 59.91 --- 68.20 8.29 1000.0 1000.000 150.0 H 128.0 82.0 TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 71 of 94

4.8.2 CONDUCTED MEASUREMENTS AT ANTENNA PORT The test was performed according to: ANSI C63.10 4.8.2.1 Test Description Please see test description for the test case “UNDESIRABLE EMISSIONS” Band Edge measurement Settings: • Detector: Peak, RMS • Trace: Max Hold, Average (Power Average) • IF Bandwidth = 1 MHz Measurements may have also been performed separately, as only Peak, Max Hold or only RMS, Power averaging. See also measurement plots. 4.8.2.2 Test Requirements / Limits Please see test description for the test case “UNDESIRABLE EMISSIONS” TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 72 of 94

4.8.2.3 Test Protocol Ambient temperature: 20–25 °C Air Pressure: 981–1026 hPa Humidity: 34–44 % WLAN a-Mode; 20 MHz; 6Mbps Ch. Band Spurious Spurious Center Edge Level Level Min. U-NII- Ch. Freq. Freq. Core 0 Core 1 Detec- RBW Limit Margin Subband No. [MHi] [MHi] [dB V/m] [dB V/m] tor [kHi] [dB V/m] [dB] 1 36 5180 5150.0 67.3 66.4 PEAK 1000 74.0 6.7 36 5180 5150.0 48.1 48.7 AV 1000 54.0 5.3 40 5200 5150.0 62.5 64.1 PEAK 1000 74.0 9.9 40 5200 5150.0 48.3 49.9 AV 1000 54.0 4.1 2A 60 5300 5350.0 62.1 62.8 PEAK 1000 74.0 11.2 60 5300 5350.0 48.4 50.4 AV 1000 54.0 3.6 64 5320 5350.0 64.3 68.5 PEAK 1000 74.0 5.5 64 5320 5350.0 48.8 50.3 AV 1000 54.0 3.7 2C 100 5500 5460.0 60.9 63.7 PEAK 1000 74.0 10.3 100 5500 5460.0 48.8 48.6 AV 1000 54.0 5.2 100 5500 5470.0 65.6 65.5 PEAK 1000 68.0 2.4 104 5520 5460.0 61.0 64.6 PEAK 1000 74.0 9.4 104 5520 5460.0 49.6 50.7 AV 1000 54.0 3.3 104 5520 5470.0 66.3 66.1 PEAK 1000 68.0 1.7 136 5680 5725.0 65.4 63.3 PEAK 1000 68.0 2.6 140 5700 5725.0 67.0 65.0 PEAK 1000 68.0 1.0 3 149 5745 5725.0 55.2 56.0 PEAK 1000 78.0 22.0 165 5825 5850.0 54.3 57.3 PEAK 1000 78.0 20.7 WLAN n-Mode; 20 MHz; MCS0 Ch. Band Spurious Spurious Spurious Center Edge Level Level Level U-NII- Ch. Freq. Freq. Core 0 Core 1 Core 0 + 1 Detec- RBW Limit Margin Subband No. [MHi] [MHi] [dB V/m] [dB V/m] [dB V/m] tor [kHi] [dB V/m] [dB] 1 36 5180 5150.0 65.0 69.6 70.9 PEAK 1000 74.0 3.1 36 5180 5150.0 47.6 49.1 51.4 AV 1000 54.0 2.6 40 5200 5150.0 63.1 66.7 68.3 PEAK 1000 74.0 5.7 40 5200 5150.0 47.3 50.5 52.2 AV 1000 54.0 1.8 2A 60 5300 5350.0 63.5 66.4 68.2 PEAK 1000 74.0 5.8 60 5300 5350.0 48.8 50.6 52.8 AV 1000 54.0 1.2 64 5320 5350.0 67.1 66.3 69.7 PEAK 1000 74.0 4.3 64 5320 5350.0 48.4 49.7 52.1 AV 1000 54.0 1.9 2C 100 5500 5460.0 67.9 65.6 69.9 PEAK 1000 74.0 4.1 100 5500 5460.0 49.4 48.5 52.0 AV 1000 54.0 2.0 100 5500 5470.0 63.3 63.0 66.2 PEAK 1000 68.0 1.8 1) 104 5520 5460.0 60.2 63.1 64.9 PEAK 1000 74.0 9.1 104 5520 5460.0 48.4 50.9 52.8 AV 1000 54.0 1.2 104 5520 5470.0 63.7 66.0 68.0 PEAK 1000 68.0 0.0 136 5680 5725.0 64.7 64.7 67.7 PEAK 1000 68.0 0.3 140 5700 5725.0 63.2 60.7 65.1 PEAK 1000 68.0 2.9 1) 3 149 5745 5725.0 55.3 57.6 59.6 PEAK 1000 78.0 18.4 165 5825 5850.0 54.3 55.2 57.8 PEAK 1000 78.0 20.2 TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 73 of 94

WLAN n-Mode; 40 MHz; MCS0 Ch. Band Spurious Spurious Spurious Center Edge Level Level Level U-NII- Ch. Freq. Freq. Core 0 Core 1 Core 0 + 1 Detec- RBW Limit Margin Subband No. [MHi] [MHi] [dB V/m] [dB V/m] [dB V/m] tor [kHi] [dB V/m] [dB] 1 38 5190 5150.0 63.7 65.0 67.4 PEAK 1000 74.0 6.6 38 5190 5150.0 45.5 46.8 49.2 AV 1000 54.0 4.8 46 5230 5150.0 60.3 62.8 64.7 PEAK 1000 74.0 9.3 46 5230 5150.0 44.7 46.8 48.9 AV 1000 54.0 5.1 2A 54 5270 5350.0 59.7 62.7 64.5 PEAK 1000 74.0 9.5 54 5270 5350.0 45.3 46.9 49.2 AV 1000 54.0 4.8 62 5310 5350.0 57.7 61.8 63.2 PEAK 1000 74.0 10.8 62 5310 5350.0 46.4 46.0 49.2 AV 1000 54.0 4.8 2C 102 5510 5460.0 68.8 67.2 71.1 PEAK 1000 74.0 2.9 102 5510 5460.0 48.4 48.1 51.3 AV 1000 54.0 2.7 102 5510 5470.0 60.0 60.0 63.0 PEAK 1000 68.0 5.0 1) 110 5550 5460.0 61.2 61.2 64.2 PEAK 1000 74.0 9.8 110 5550 5460.0 49.1 47.9 51.6 AV 1000 54.0 2.4 110 5550 5470.0 64.6 62.4 66.6 PEAK 1000 68.0 1.4 126 5630 5725.0 58.2 57.7 61.0 PEAK 1000 68.0 7.0 134 5670 5725.0 63.5 60.3 65.2 PEAK 1000 68.0 2.8 3 151 5755 5725.0 63.7 62.6 66.2 PEAK 1000 78.0 11.8 159 5795 5850.0 56.6 54.4 58.6 PEAK 1000 78.0 19.4 WLAN ac-Mode; 80 MHz; MCS0 Ch. Band Spurious Spurious Spurious Center Edge Level Level Level U-NII- Ch. Freq. Freq. Core 0 Core 1 Core 0 + 1 Detec- RBW Limit Margin Subband No. [MHi] [MHi] [dB V/m] [dB V/m] [dB V/m] tor [kHi] [dB V/m] [dB] 1 38 5190 5150.0 60.3 61.6 64.0 PEAK 1000 74.0 10.0 38 5190 5150.0 45.4 45.9 48.7 AV 1000 54.0 5.3 2A 54 5270 5350.0 60.3 61.0 63.7 PEAK 1000 74.0 10.3 54 5270 5350.0 45.9 46.1 49.0 AV 1000 54.0 5.0 2C 106 5530 5460.0 63.3 61.8 65.6 PEAK 1000 74.0 8.4 106 5530 5460.0 47.6 47.0 50.3 AV 1000 54.0 3.7 106 5530 5470.0 64.6 63.6 67.1 PEAK 1000 68.0 0.9 122 5610 5725.0 57.9 54.6 59.6 PEAK 1000 68.0 8.4 3 151 5755 5725.0 64.7 65.4 68.1 PEAK 1000 78.0 9.9 159 5795 5850.0 58.7 58.0 61.4 PEAK 1000 78.0 16.6 1) Integration method used. Remark: Please see next sub-clause for the measurement plot. TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 74 of 94

4.8.2.4 Measurement Plot (showing the highest value, “worst case”) Radio Technology = WLAN a 20 MHz (S01_3_AA01) Core 0 Band 1/2A lowest / highest Core 0 Band 1/2A 2nd lowest / highest Core 1 Band 1/2A lowest / highest Core 1 Band 1/2A 2nd lowest / highest Date:31.JAN.2018 12:09:54 Core 0 Band 2C lowest / highest Core 0 Band 2C 2nd lowest / highest TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 75 of 94

Core 1 Band 2C lowest / highest Core 1 Band 2C 2nd lowest / highest Core 0 Band 3 lowest / highest Core 1 Band 3 lowest / highest Radio Technology = WLAN n 20 MHz (S01_3_AA01) Core 0 Band 1/2A lowest / highest Core 0 Band 1/2A 2nd lowest / highest TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 76 of 94

Core 1 Band 1/2A lowest / highest Core 1 Band 1/2A 2nd lowest / highest Core 0 Band 2C lowest / highest Core 0 Band 2C 2nd lowest / highest Core 0 Band 2C lowest integration method Core 0 Band 2C highest integration method TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 77 of 94

Core 1 Band 2C lowest / highest Core 1 Band 2C 2nd lowest / highest Core 1 Band 2C lowest integration method Core 1 Band 2C highest integration method Core 0 Band 3 lowest / highest Core 1 Band 3 lowest / highest TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 78 of 94

Radio Technology = WLAN n 40 MHz (S01_3_AA01) Core 0 Band 1/2A lowest / highest Core 0 Band 1/2A 2nd lowest / highest Core 1 Band 1/2A lowest / highest Core 1 Band 1/2A 2nd lowest / highest Core 0 Band 2C lowest / highest Core 0 Band 2C 2nd lowest / highest TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 79 of 94

Core 1 Band 2C lowest / highest Core 1 Band 2C 2nd lowest / highest Core 0 Band 2C lowest integration method Core 1 Band 2C lowest integration method Core 0 Band 3 lowest / highest Core 1 Band 3 lowest / highest TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 80 of 94

Radio Technology = WLAN ac 80 MHz (S01_3_AA01) Core 0 Band 1/2A lowest / highest Core 1 Band 1/2A lowest / highest Core 0 Band 2C lowest / highest Core 1 Band 2C lowest / highest Core 0 Band 3 lowest / highest Core 1 Band 3 lowest / highest 4.8.3 TEST EQUIPMENT USED - Radiated Emissions - R&S TS8997 TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 81 of 94

4.9 DYNAMIC FREQUENCY SELECTION Standard FCC Part 15 Subpart E The test was performed according to: ANSI C63.10 4.9.1 TEST DESCRIPTION The Equipment Under Test (EUT) was set up in a shielded room for the DFS measurements. Since the EUT is a slave device without radar detection, it was connected to another device acting as master with radar detection. After setting up a connection to the Master using the maximum supported bandwidth of the EUT, a radar pulse of type 0 was send from the vector signal generator. At the same time the spectrum analyser is triggered by the vector signal generator and a trace is recorded: Analyzer settings: • Resolution Bandwidth (RBW): 3 MHz • Video Bandwidth (VBW): 3 MHz • Trace: Clear/Write • Sweeps: Single Sweep • Sweeptime: 20 s • Detector: Peak • Trigger: External In addition to the plot also the trace data is recorded to calculate the Channel Closing Time. Afterwards the test is repeated with a sweep time of 32 minutes to monitor the Non-occupancy period. TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 82 of 94

4.9.2 TEST REQUIREMENTS / LIMITS Limits according KDB 905462 D02 UNII DFS Compliance Procedures New Rules Parameter Value Non-occupancy period Minimum 30 minutes Channel Availability Check Time 60 seconds Channel Move Time 10 seconds See Note 1. Channel Closing Transmission Time 200 milliseconds + an aggregate of 60 milliseconds over remaining 10 second period. See Notes 1 and 2. Note 1: Channel Move Time and the Channel Closing Transmission Time should be performed with Radar Type 0. The measurement timing begins at the end of the Radar Type 0 burst. Note 2: The Channel Closing Transmission Time is comprised of 200 milliseconds starting at the beginning of the Channel Move Time plus any additional intermittent control signals required to facilitate a Channel move (an aggregate of 60 milliseconds) during the remainder of the 10 second period. The aggregate duration of control signals will not count quiet periods in between transmissions. 4.9.3 TEST PROTOCOL Ambient temperature: 24 °C Air Pressure: 1002 hPa Humidity: 30 % WLAN ac-Mode; 80 MHz Aggregate Transmission Ch. Transmissions Time from 200 Channel Ch. Center Limit Margin within ms to 10 s after move time No. Freq. [ms] [ms] Non-occupancy end of radar within 10 s [MHi] period pulse [ms] 106 5530 4.7 60.0 55.3 yes none Remark: Please see next sub-clause for the measurement plot. TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 83 of 94

4.9.4 MEASUREMENT PLOT (SHOWING THE HIGHEST VALUE, “WORST CASE”) (S01_3_AA01) Channel Closing Time Non Occupancy Period 4.9.5 TEST EQUIPMENT USED - R&S TS8997 TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 84 of 94

5 TEST EQUIPMENT 1 R&S TS8997 EN300328/301893 Test Lab Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 1.1 SMB100A Signal Rohde & Schwarz 107695 2017-07 2020-07 Generator 9 kHz - 6 GHz 1.2 MFS Rubidium Datum-Beverly 5489/001 2017-07 2018-07 Frequency Standard 1.3 1515 / 93459 Broadband Weinschel LN673 Power Divider Associates SMA (Aux) 1.4 FSV30 Signal Rohde & Schwarz 103005 2016-02 2018-02 Analyzer 10 Hz - 30 GHz 1.5 Fluke 177 Digital Fluke Europe B.V. 86670383 2016-02 2018-02 Multimeter 03 (Multimeter) 1.6 VT 4002 Climatic Vötsch 58566002150010 2016-03 2018-03 Chamber 1.7 A8455-4 4 Way Power - Divider (SMA) 1.8 Opus10 THI ThermoHygro Lufft Mess- und 7482 2017-03 2019-03 (8152.00) Datalogger 03 Regeltechnik GmbH (Environ) 1.9 SMBV100A Vector Signal Rohde & Schwarz 259291 2016-10 2019-10 Generator 9 kHz - 6 GHz 1.10 OSP120 Switching Unit Rohde & Schwarz 101158 2016-11 2018-11 with integrated power meter 2 Radiated Emissions Lab to perform radiated emission tests Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 2.1 NRV-Z1 Sensor Head A Rohde & Schwarz 827753/005 2017-05 2018-05 2.2 MFS Rubidium Datum GmbH 002 2017-10 2018-10 Frequency Normal MFS 2.3 Opus10 TPR ThermoAirpres Lufft Mess- und 13936 2017-04 2019-04 (8253.00) sure Regeltechnik GmbH Datalogger 13 (Environ) 2.4 Anechoic 10.58 x 6.38 x Frankonia none 2016-05 2019-05 Chamber 6.00 m 2.5 HL 562 Ultralog new Rohde & Schwarz 830547/003 2015-06 2018-06 biconicals 2.6 5HC2700/12750 High Pass Trilithic 9942012 -1.5-KK Filter 2.7 ASP 1.2/1.8-10 Antenna Mast Maturo GmbH - kg TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 85 of 94

Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 2.8 Fully Anechoic 8.80m x Albatross Projects P26971-647-001- 2015-06 2018-06 Room 4.60m x PRB 4.05m (l x w x h) 2.9 Fluke 177 Digital Fluke Europe B.V. 86670383 2016-02 2018-02 Multimeter 03 (Multimeter) 2.10 JS4-18002600- Broadband Miteq 849785 32-5P Amplifier 18 GHz - 26 GHz 2.11 FSW 43 Spectrum Rohde & Schwarz 103779 2016-12 2018-12 Analyzer 2.12 3160-09 Standard Gain EMCO Elektronic 00083069 / Pyramidal GmbH Horn Antenna 26.5 GHz 2.13 WHKX 7.0/18G- High Pass Wainwright 09 8SS Filter 2.14 4HC1600/12750 High Pass Trilithic 9942011 -1.5-KK Filter 2.15 Chroma 6404 AC Power Chroma ATE INC. 64040001304 Source 2.16 JS4-00102600- Broadband Miteq 619368 42-5A Amplifier 30 MHz - 26 GHz 2.17 TT 1.5 WI Turn Table Maturo GmbH - 2.18 HL 562 Ultralog Log.-per. Rohde & Schwarz 100609 2016-04 2019-04 Antenna 2.19 3160-10 Standard Gain EMCO Elektronic 00086675 / Pyramidal GmbH Horn Antenna 40 GHz 2.20 5HC3500/18000 High Pass Trilithic 200035008 -1.2-KK Filter 2.21 HFH2-Z2 Loop Antenna Rohde & Schwarz 829324/006 2014-11 2017-11 2.22 Opus10 THI ThermoHygro Lufft Mess- und 12482 2017-03 2019-03 (8152.00) Datalogger 12 Regeltechnik GmbH (Environ) 2.23 ESR 7 EMI Receiver / Rohde & Schwarz 101424 2016-11 2018-11 Spectrum Analyzer 2.24 JS4-00101800- Broadband Miteq 896037 35-5P Amplifier 30 MHz - 18 GHz 2.25 AS 620 P Antenna mast HD GmbH 620/37 2.26 Tilt device Antrieb TD1.5- Maturo GmbH TD1.5- Maturo 10kg 10kg/024/37907 (Rohacell) 09 2.27 ESIB 26 Spectrum Rohde & Schwarz 830482/004 2015-12 2017-12 Analyzer 2.28 PAS 2.5 - 10 kg Antenna Mast Maturo GmbH - 2.29 AM 4.0 Antenna mast Maturo GmbH AM4.0/180/1192 0513 2.30 HF 907 Double-ridged Rohde & Schwarz 102444 2015-05 2018-05 horn The calibration interval is the time interval between “Last Calibration” and “Calibration Due” TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 86 of 94

6 ANTENNA FACTORS, CABLE LOSS AND SAMPLE CALCULATIONS This chapter contains the antenna factors with their corresponding path loss of the used measurement path for all antennas as well as the insertion loss of the LISN. 6.1 LISN R&S ESH3-Z5 (150 KHZ – 30 MHZ) cable LISN loss insertion (incl. 10 loss dB ESH3- atten- Frequency Corr. Z5 uator) MHz dB dB dB 0.15 10.1 0.1 10.0 5 10.3 0.1 10.2 7 10.5 0.2 10.3 10 10.5 0.2 10.3 12 10.7 0.3 10.4 14 10.7 0.3 10.4 16 10.8 0.4 10.4 18 10.9 0.4 10.5 20 10.9 0.4 10.5 22 11.1 0.5 10.6 24 11.1 0.5 10.6 26 11.2 0.5 10.7 28 11.2 0.5 10.7 30 11.3 0.5 10.8 Sample calculation ULISN (dB V) = U (dB V) + Corr. (dB) U = Receiver reading LISN Insertion loss = Voltage Division Factor of LISN Corr. = sum of single correction factors of used LISN, cables, switch units (if used) Linear interpolation will be used for frequencies in between the values in the table. TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 87 of 94

6.2 ANTENNA R&S HFH2-Z2 (9 KHZ – 30 MHZ) cable cable cable cable distance dLimit dused loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. AF (inside (outside (switch (to (-40 dB/ distance distance Frequency HFH-Z2) Corr. chamber) chamber) unit) receiver) decade) (limit) (used) MHz dB (1/m) dB dB dB dB dB dB m m 0.009 20.50 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.01 20.45 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.015 20.37 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.02 20.36 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.025 20.38 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.03 20.32 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.05 20.35 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.08 20.30 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.1 20.20 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.2 20.17 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.3 20.14 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.49 20.12 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.490001 20.12 -39.6 0.1 0.1 0.1 0.1 -40 30 3 0.5 20.11 -39.6 0.1 0.1 0.1 0.1 -40 30 3 0.8 20.10 -39.6 0.1 0.1 0.1 0.1 -40 30 3 1 20.09 -39.6 0.1 0.1 0.1 0.1 -40 30 3 2 20.08 -39.6 0.1 0.1 0.1 0.1 -40 30 3 3 20.06 -39.6 0.1 0.1 0.1 0.1 -40 30 3 4 20.05 -39.5 0.2 0.1 0.1 0.1 -40 30 3 5 20.05 -39.5 0.2 0.1 0.1 0.1 -40 30 3 6 20.02 -39.5 0.2 0.1 0.1 0.1 -40 30 3 8 19.95 -39.5 0.2 0.1 0.1 0.1 -40 30 3 10 19.83 -39.4 0.2 0.1 0.2 0.1 -40 30 3 12 19.71 -39.4 0.2 0.1 0.2 0.1 -40 30 3 14 19.54 -39.4 0.2 0.1 0.2 0.1 -40 30 3 16 19.53 -39.3 0.3 0.1 0.2 0.1 -40 30 3 18 19.50 -39.3 0.3 0.1 0.2 0.1 -40 30 3 20 19.57 -39.3 0.3 0.1 0.2 0.1 -40 30 3 22 19.61 -39.3 0.3 0.1 0.2 0.1 -40 30 3 24 19.61 -39.3 0.3 0.1 0.2 0.1 -40 30 3 26 19.54 -39.3 0.3 0.1 0.2 0.1 -40 30 3 28 19.46 -39.2 0.3 0.1 0.3 0.1 -40 30 3 30 19.73 -39.1 0.4 0.1 0.3 0.1 -40 30 3 Sample calculation E (dB V/m) = U (dB V) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) distance correction = -40 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 88 of 94

6.3 ANTENNA R&S HL562 (30 MHZ – 1 GHZ) (dLimit = 3 m) cable cable cable cable distance dLimit dused AF loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. R&S (inside (outside (switch (to (-20 dB/ distance distance Frequency HL562 Corr. chamber) chamber) unit) receiver) decade) (limit) (used) MHz dB (1/m) dB dB dB dB dB dB m m 30 18.6 0.6 0.29 0.04 0.23 0.02 0.0 3 3 50 6.0 0.9 0.39 0.09 0.32 0.08 0.0 3 3 100 9.7 1.2 0.56 0.14 0.47 0.08 0.0 3 3 150 7.9 1.6 0.73 0.20 0.59 0.12 0.0 3 3 200 7.6 1.9 0.84 0.21 0.70 0.11 0.0 3 3 250 9.5 2.1 0.98 0.24 0.80 0.13 0.0 3 3 300 11.0 2.3 1.04 0.26 0.89 0.15 0.0 3 3 350 12.4 2.6 1.18 0.31 0.96 0.13 0.0 3 3 400 13.6 2.9 1.28 0.35 1.03 0.19 0.0 3 3 450 14.7 3.1 1.39 0.38 1.11 0.22 0.0 3 3 500 15.6 3.2 1.44 0.39 1.20 0.19 0.0 3 3 550 16.3 3.5 1.55 0.46 1.24 0.23 0.0 3 3 600 17.2 3.5 1.59 0.43 1.29 0.23 0.0 3 3 650 18.1 3.6 1.67 0.34 1.35 0.22 0.0 3 3 700 18.5 3.6 1.67 0.42 1.41 0.15 0.0 3 3 750 19.1 4.1 1.87 0.54 1.46 0.25 0.0 3 3 800 19.6 4.1 1.90 0.46 1.51 0.25 0.0 3 3 850 20.1 4.4 1.99 0.60 1.56 0.27 0.0 3 3 900 20.8 4.7 2.14 0.60 1.63 0.29 0.0 3 3 950 21.1 4.8 2.22 0.60 1.66 0.33 0.0 3 3 1000 21.6 4.9 2.23 0.61 1.71 0.30 0.0 3 3 (dLimit = 10 m) 30 18.6 -9.9 0.29 0.04 0.23 0.02 -10.5 10 3 50 6.0 -9.6 0.39 0.09 0.32 0.08 -10.5 10 3 100 9.7 -9.2 0.56 0.14 0.47 0.08 -10.5 10 3 150 7.9 -8.8 0.73 0.20 0.59 0.12 -10.5 10 3 200 7.6 -8.6 0.84 0.21 0.70 0.11 -10.5 10 3 250 9.5 -8.3 0.98 0.24 0.80 0.13 -10.5 10 3 300 11.0 -8.1 1.04 0.26 0.89 0.15 -10.5 10 3 350 12.4 -7.9 1.18 0.31 0.96 0.13 -10.5 10 3 400 13.6 -7.6 1.28 0.35 1.03 0.19 -10.5 10 3 450 14.7 -7.4 1.39 0.38 1.11 0.22 -10.5 10 3 500 15.6 -7.2 1.44 0.39 1.20 0.19 -10.5 10 3 550 16.3 -7.0 1.55 0.46 1.24 0.23 -10.5 10 3 600 17.2 -6.9 1.59 0.43 1.29 0.23 -10.5 10 3 650 18.1 -6.9 1.67 0.34 1.35 0.22 -10.5 10 3 700 18.5 -6.8 1.67 0.42 1.41 0.15 -10.5 10 3 750 19.1 -6.3 1.87 0.54 1.46 0.25 -10.5 10 3 800 19.6 -6.3 1.90 0.46 1.51 0.25 -10.5 10 3 850 20.1 -6.0 1.99 0.60 1.56 0.27 -10.5 10 3 900 20.8 -5.8 2.14 0.60 1.63 0.29 -10.5 10 3 950 21.1 -5.6 2.22 0.60 1.66 0.33 -10.5 10 3 1000 21.6 -5.6 2.23 0.61 1.71 0.30 -10.5 10 3 Sample calculation E (dB V/m) = U (dB V) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) distance correction = -20 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Tables show an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 89 of 94

6.4 ANTENNA R&S HF907 (1 GHZ – 18 GHZ) cable cable loss 3 loss 1 (switch (relay + cable unit, AF cable loss 2 atten- cable R&S inside (outside uator & loss 4 (to Frequency HF907 Corr. chamber) chamber) pre-amp) receiver) MHz dB (1/m) dB dB dB dB dB 1000 24.4 -19.4 0.99 0.31 -21.51 0.79 2000 28.5 -17.4 1.44 0.44 -20.63 1.38 3000 31.0 -16.1 1.87 0.53 -19.85 1.33 4000 33.1 -14.7 2.41 0.67 -19.13 1.31 5000 34.4 -13.7 2.78 0.86 -18.71 1.40 6000 34.7 -12.7 2.74 0.90 -17.83 1.47 7000 35.6 -11.0 2.82 0.86 -16.19 1.46 cable loss 4 cable (switch loss 1 cable cable unit, used AF (relay loss 2 loss 3 atten- cable for R&S inside (inside (outside uator & loss 5 (to FCC Frequency HF907 Corr. chamber) chamber) chamber) pre-amp) receiver) 15.247 MHz dB (1/m) dB dB dB dB dB dB 3000 31.0 -23.4 0.47 1.87 0.53 -27.58 1.33 4000 33.1 -23.3 0.56 2.41 0.67 -28.23 1.31 5000 34.4 -21.7 0.61 2.78 0.86 -27.35 1.40 6000 34.7 -21.2 0.58 2.74 0.90 -26.89 1.47 7000 35.6 -19.8 0.66 2.82 0.86 -25.58 1.46 cable loss 1 cable cable cable cable cable AF (relay loss 2 loss 3 loss 4 loss 5 loss 6 R&S inside (High (pre- (inside (outside (to Frequency HF907 Corr. chamber) Pass) amp) chamber) chamber) receiver) MHz dB (1/m) dB dB dB dB dB dB dB 7000 35.6 -57.3 0.56 1.28 -62.72 2.66 0.94 1.46 8000 36.3 -56.3 0.69 0.71 -61.49 2.84 1.00 1.53 9000 37.1 -55.3 0.68 0.65 -60.80 3.06 1.09 1.60 10000 37.5 -56.2 0.70 0.54 -61.91 3.28 1.20 1.67 11000 37.5 -55.3 0.80 0.61 -61.40 3.43 1.27 1.70 12000 37.6 -53.7 0.84 0.42 -59.70 3.53 1.26 1.73 13000 38.2 -53.5 0.83 0.44 -59.81 3.75 1.32 1.83 14000 39.9 -56.3 0.91 0.53 -63.03 3.91 1.40 1.77 15000 40.9 -54.1 0.98 0.54 -61.05 4.02 1.44 1.83 16000 41.3 -54.1 1.23 0.49 -61.51 4.17 1.51 1.85 17000 42.8 -54.4 1.36 0.76 -62.36 4.34 1.53 2.00 18000 44.2 -54.7 1.70 0.53 -62.88 4.41 1.55 1.91 Sample calculation E (dB V/m) = U (dB V) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. Tables show an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 90 of 94

6.5 ANTENNA EMCO 3160-09 (18 GHZ – 26.5 GHZ) cable cable cable cable cable AF loss 1 loss 2 loss 3 loss 4 loss 5 EMCO (inside (pre- (inside (switch (to Frequency 3160-09 Corr. chamber) amp) chamber) unit) receiver) MHz dB (1/m) dB dB dB dB dB dB 18000 40.2 -23.5 0.72 -35.85 6.20 2.81 2.65 18500 40.2 -23.2 0.69 -35.71 6.46 2.76 2.59 19000 40.2 -22.0 0.76 -35.44 6.69 3.15 2.79 19500 40.3 -21.3 0.74 -35.07 7.04 3.11 2.91 20000 40.3 -20.3 0.72 -34.49 7.30 3.07 3.05 20500 40.3 -19.9 0.78 -34.46 7.48 3.12 3.15 21000 40.3 -19.1 0.87 -34.07 7.61 3.20 3.33 21500 40.3 -19.1 0.90 -33.96 7.47 3.28 3.19 22000 40.3 -18.7 0.89 -33.57 7.34 3.35 3.28 22500 40.4 -19.0 0.87 -33.66 7.06 3.75 2.94 23000 40.4 -19.5 0.88 -33.75 6.92 3.77 2.70 23500 40.4 -19.3 0.90 -33.35 6.99 3.52 2.66 24000 40.4 -19.8 0.88 -33.99 6.88 3.88 2.58 24500 40.4 -19.5 0.91 -33.89 7.01 3.93 2.51 25000 40.4 -19.3 0.88 -33.00 6.72 3.96 2.14 25500 40.5 -20.4 0.89 -34.07 6.90 3.66 2.22 26000 40.5 -21.3 0.86 -35.11 7.02 3.69 2.28 26500 40.5 -21.1 0.90 -35.20 7.15 3.91 2.36 Sample calculation E (dB V/m) = U (dB V) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 91 of 94

6.6 ANTENNA EMCO 3160-10 (26.5 GHZ – 40 GHZ) cable cable cable cable distance dLimit dused AF loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. EMCO (inside (outside (switch (to (-20 dB/ distance distance Frequency 3160-10 Corr. chamber) chamber) unit) receiver) decade) (limit) (used) GHz dB (1/m) dB dB dB dB dB dB m m 26.5 43.4 -11.2 4.4 -15.6 3 0.5 27.0 43.4 -11.2 4.4 -15.6 3 0.5 28.0 43.4 -11.1 4.5 -15.6 3 0.5 29.0 43.5 -11.0 4.6 -15.6 3 0.5 30.0 43.5 -10.9 4.7 -15.6 3 0.5 31.0 43.5 -10.8 4.7 -15.6 3 0.5 32.0 43.5 -10.7 4.8 -15.6 3 0.5 33.0 43.6 -10.7 4.9 -15.6 3 0.5 34.0 43.6 -10.6 5.0 -15.6 3 0.5 35.0 43.6 -10.5 5.1 -15.6 3 0.5 36.0 43.6 -10.4 5.1 -15.6 3 0.5 37.0 43.7 -10.3 5.2 -15.6 3 0.5 38.0 43.7 -10.2 5.3 -15.6 3 0.5 39.0 43.7 -10.2 5.4 -15.6 3 0.5 40.0 43.8 -10.1 5.5 -15.6 3 0.5 Sample calculation E (dB V/m) = U (dB V) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. distance correction = -20 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 92 of 94

7 SETUP DRAWINGS Drawing 1: Setup in the Anechoic chamber. For measurements below 1 GHz the ground was replaced by a conducting groundplane. TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 93 of 94

8 MEASUREMENT UNCERTAINTIES Test Case Parameter Uncertainty AC Power Line Power ± 3.4 dB Field Strength of spurious radiation Power ± 5.5 dB 6 dB / 26 dB / 99% Bandwidth Power ± 2.9 dB Frequency ± 11.2 kHz Conducted Output Power Power ± 2.2 dB Band Edge Compliance Power ± 2.2 dB Frequency ± 11.2 kHz Frequency Stability Frequency ± 25 Hz Power Spectral Density Power ± 2.2 dB 9 PHOTO REPORT Please see separate photo report. TEST REPORT REFERENCE: MDE_UBLOX_1701_FCCb Page 94 of 94


Document Created: 2019-04-05 22:47:20
Document Modified: 2019-04-05 22:47:20
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC