Test Report WLAN

FCC ID: XPYEMMYW163

Test Report

Download: PDF
FCCID_3884382

FCC Measurement/Technical Report on Host-based multiradio module with Wi-Fi, Bluetooth and NFC EMMY-W163 in WLAN 2.4 GHz mode FCC ID: EMMY-W161: XPYEMMYW163 IC: EMMY-W161: 8595A-EMMYW163 Test Report Reference: MDE_LESSW_1701_FCCa Test Laboratory: 7layers GmbH Borsigstrasse 11 40880 Ratingen Germany Note: The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts without the written approval of the test laboratory. 7layers GmbH Geschäftsführer/ Borsigstraße 11 Managing Directors: Registergericht/registered: a Bureau Veritas 40880 Ratingen, Germany Frank Spiller Düsseldorf HRB 75554 Group Company T +49 (0) 2102 749 0 Bernhard Retka USt-Id.-Nr./VAT-No. DE203159652 F +49 (0) 2102 749 350 Alexandre Norré-Oudard Steuer-Nr./TAX-No. 147/5869/0385 www.7layers.com Commerzbank AG Account No. 303 016 000 Bank Code 300 400 00 IBAN DE81 3004 0000 0303 0160 00 Swift Code COBADEFF

Table of Contents 1 Applied Standards and Test Summary 3 1.1 Applied Standards 3 1.2 FCC-IC Correlation Table 4 1.3 Measurement Summary / Signatures 5 2 Administrative Data 6 2.1 Testing Laboratory 6 2.2 Project Data 6 2.3 Applicant Data 6 2.4 Manufacturer Data 7 3 Test object Data 8 3.1 General EUT Description 8 3.2 EUT Main components 9 3.3 WLAN Power Table 10 3.4 Ancillary Equipment 10 3.5 Auxiliary Equipment 11 3.6 EUT Setups 11 3.7 Operating Modes 12 3.8 Product labelling 12 4 Test Results 13 4.1 Transmitter Spurious Radiated Emissions 13 4.2 Band Edge Compliance Radiated 17 5 Test Equipment 20 6 Antenna Factors, Cable Loss and Sample Calculations 22 6.1 LISN R&S ESH3-Z5 (150 kHz – 30 MHz) 22 6.2 Antenna R&S HFH2-Z2 (9 kHz – 30 MHz) 23 6.3 Antenna R&S HL562 (30 MHz – 1 GHz) 24 6.4 Antenna R&S HF907 (1 GHz – 18 GHz) 25 6.5 Antenna EMCO 3160-09 (18 GHz – 26.5 GHz) 26 6.6 Antenna EMCO 3160-10 (26.5 GHz – 40 GHz) 27 7 Setup Drawings 28 8 Measurement Uncertainties 29 9 Photo Report 29 TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 2 of 29

1 APPLIED STANDARDS AND TEST SUMMARY 1.1 APPLIED STANDARDS Type of Authorization Certification for an Intentional Radiator. Applicable FCC Rules Prepared in accordance with the requirements of FCC Rules and Regulations as listed in 47 CFR Ch.1 Parts 2 and 15 (10-1-15 Edition). The following subparts are applicable to the results in this test report. Part 2, Subpart J - Equipment Authorization Procedures, Certification Part 15, Subpart C – Intentional Radiators § 15.201 Equipment authorization requirement § 15.207 Conducted limits § 15.209 Radiated emission limits; general requirements § 15.247 Operation within the bands 902-928 MHz, 2400-2483.5 MHz Note 1: The tests were selected and performed with reference to the FCC Public Notice “GUIDANCE FOR PERFORMING COMPLIANCE MEASUREMENTS ON DIGITAL TRANSMISSION SYSTEMS (DTS) OPERATING UNDER §15.247, 558074 D01 DTS Meas Guidance v04, 2017-04-05”. ANSI C63.10–2013 is applied. Note 2: Not all possible operating modes were tested. Worst case operating modes were determined at the beginning of the test period. TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 3 of 29

Summary Test Results: The EUT complied with all performed tests as listed in chapter 1.3 Measurement Summary / Signatures. 1.2 FCC-IC CORRELATION TABLE Correlation of measurement requirements for DTS (e.g. WLAN 2.4 GHz, BT LE) equipment from FCC and IC DTS equipment Measurement FCC reference IC reference Conducted emissions on AC § 15.207 RSS-Gen Issue 4: 8.8 Mains Occupied bandwidth § 15.247 (a) (2) RSS-247 Issue 2: 5.2 (a) Peak conducted output § 15.247 (b) (3), (4) RSS-247 Issue 2: 5.4 (d) power Transmitter spurious RF § 15.247 (d) RSS-Gen Issue 4: 6.13 / conducted emissions 8.9/8.10; RSS-247 Issue 2: 5.5 Transmitter spurious § 15.247 (d); RSS-Gen Issue 4: 6.13 / radiated emissions § 15.209 (a) 8.9/8.10; RSS-247 Issue 2: 5.5 Band edge compliance § 15.247 (d) RSS-247 Issue 2: 5.5 Power density § 15.247 (e) RSS-247 Issue 2: 5.2 (b) Antenna requirement § 15.203 / 15.204 RSS-Gen Issue 4: 8.3 Receiver spurious emissions – – TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 4 of 29

%layers A Bureau Veritas Group Company 1.3 MEASUREMENT SUMMARY / SIGNATURES 47 CFR CHAPTER I FCC PART 15 Subpart C § 15.247 (d) §15.247 Transmitter Spurious Radiated Emissions The measurement was performed according to ANSI C63.10 Final Result OP—Mode Setup FCC IC Radio Technology, Operating Frequency, Measurement range WLAN n, high, 1 GHz — 24 GHz DE1072001 Passed Passed aa01 47 CFR CHAPTER I FCC PART 15 Subpart C § 15.247 (d) §15.247 Band Edge Compliance Radiated The measurement was performed according to ANSI C63.10 Final Result OP—Mode Setup FCC IC Radio Technology, Operating Frequency, Band Edge b—Mode_2467MHz_15dBm_2Mbit_20MHzBW DE1072001 Passed Passed aa01 g—Mode_2462MHz_13dBm_9Mbit_20MHzBW g—Mode_2467MHz_9dBm_48Mbit_20MHzBW n—Mode_2447MHz_13dBm_MCSO_40MHzBW n—Mode_2447MHz_13dBm_MCS6_40MHzBW n—Mode_2452MHz_11dBm_MCS6_40MHzBW n—Mode_2462MHz_7dBm_MCS6_40MHzBW n—Mode_2462MHz_12dBm_MCS6_20MHzBW n—Mode_2467MHz_9dBm_MCS6_20MHzBW n—Mode_2467MHz_10dBm_MCS2_20MHzBW Remark: Reduced test plan has been used as it is a Class II Permissive Change [ layers EE?_E 7 layers GmbH, Borsigstr. 11 40880 Ratingen, Germany Phone +49 (0)2102 749 0 (responsible for accreditation scope) (7 spon5|bfe for testing and re Dipl.—Ing. Marco Kullik Dipl.—Ing. Imad HJIJe TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 5 of 29

2 ADMINISTRATIVE DATA 2.1 TESTING LABORATORY Company Name: 7layers GmbH Address: Borsigstr. 11 40880 Ratingen Germany This facility has been fully described in a report submitted to the ISED and accepted under the registration number: Site# 3699A-1. The test facility is also accredited by the following accreditation organisation: Laboratory accreditation no: DAkkS D-PL-12140-01-00 FCC Designation Number: DE0015 FCC Test Firm Registration: 929146 Responsible for accreditation scope: Dipl.-Ing. Marco Kullik Report Template Version: 2017-07-14 Company Name: 7layers GmbH Address: Borsigstr. 11 40880 Ratingen Germany 2.2 PROJECT DATA Responsible for testing and report: Dipl.-Ing. Imad Hjije Employees who performed the tests: documented internally at 7Layers Date of Report: 2018-03-21 Testing Period: 2018-02-15 to 2018-02-16 2.3 APPLICANT DATA Company Name: u-blox AG Address: Zürcherstrasse 68 8800 Thalwil Switzerland Contact Person: Mr. Giulio Comar TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 6 of 29

2.4 MANUFACTURER DATA Company Name: please see applicant data Address: Contact Person: TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 7 of 29

3 TEST OBJECT DATA 3.1 GENERAL EUT DESCRIPTION Kind of Device WLAN 2.4 GHz, 5 GHz, BT, NFC, SRD (5.8 GHz) - Single Antenna product description Product name Host-based multiradio module with Wi-Fi, Bluetooth and NFC for “Mercedes-Benz-Link” Type EMMY-W163 Declared EUT data by the supplier Voltage Type DC Voltage Level normal: 3.3 V DC low: 3.0 V DC high: 3.6 V DC Modulation Type Bluetooth LE: GFSK WLAN: DSSS, OFDM, HT20 MCS0 – MCS7, HT40 MCS0 –MCS7, VHT. Please see each test protocol General product EMMY-W163 are ultra-compact multi-radio modules providing Wi- description Fi, Classic Bluetooth, Bluetooth low energy and NFC mode of operation. It is designed for both simultaneous and independent operations of: • Wi-Fi IEEE 802.11ac and a/b/g/n • Dual-mode Bluetooth 4.2 • NFC Specific product Shielded module, single antenna pin for WLAN 802.11 ac/a/b/g/n description for the EUT and Bluetooth communication The EUT provides the - DC power supply following ports: - antenna port - signal ports Data rates Bluetooth LE, GFSK: 1 Mbit/s WLAN b: please see chapter “WLAN Power Table” WLAN g: please see chapter “WLAN Power Table” WLAN n 20 MHz: please see chapter “WLAN Power Table” WLAN n 40 MHz: please see chapter “WLAN Power Table” Power levels Bluetooth LE: 5 dBm WLAN: please see chapter “WLAN Power Table” The main components of the EUT are listed and described in chapter 3.2 EUT Main components. TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 8 of 29

3.2 EUT MAIN COMPONENTS Sample Name Sample Code Description DE1072001aa01 aa01 Sample Parameter Value Antenna - SR42W001 - Dual-Band Chip Antenna, 2.4..2.5GHz (2.0dBi), 4.9..5.9GHz (3.0dBi), 11.3x5.0x0.8mm, -40..+125°C - W800 - Antenova SR42W001 Serial No. D4CA6E50CAC4 HW Version - SW Version 15.68.7.p101 Comment - TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 9 of 29

3.3 WLAN POWER TABLE Declared Power limits vs channel for FCC Modulation WLAN TX Power in dBm at frequency in MHz group 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 2472 DSSS 1, 2, 18 18 18 18 18 18 18 18 18 18 18 15 13 5.5, 11 Mbps OFDM 6, 9, 13 16 16 16 16 16 16 16 16 15 13 10 9 12, 18 Mbps OFDM 24, 36 13 16 16 16 16 16 16 16 16 15 13 10 9 Mbps OFDM 48, 54 13 13 13 13 13 13 13 13 13 13 13 9 9 Mbps HT20 MCS0, 13 15 16 16 16 16 16 16 16 16 12 10 9 MCS1, MCS2 HT20 MCS3, 13 15 16 16 16 16 16 16 16 16 12 9 9 MCS4 HT20 MCS5, 13 13 13 13 13 13 13 13 13 13 12 9 9 MCS6, MCS7 Modulation WLAN TX Power in dBm at frequency in MHz group 2422 2427 2432 2437 2442 2447 2452 2457 2462 HT40 MCS0, 11 11 13 14 14 13 10 7 6 MCS1, MCS2 HT40 MCS3, 11 11 13 14 14 13 10 7 6 MCS4 HT40 MCS5, 11 12 13 13 13 13 11 8 7 MCS6, MCS7 Remark: Please see detailed EUT settings in the test protocols. 3.4 ANCILLARY EQUIPMENT For the purposes of this test report, ancillary equipment is defined as equipment which is used in conjunction with the EUT to provide operational and control features to the EUT. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Ancillary Equipment can influence the test results. Device Details Description (Manufacturer, Type Model, OUT Code) Evaluation board (target lesswire GmbH, MB Link, telematics unit platform) TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 10 of 29

3.5 AUXILIARY EQUIPMENT For the purposes of this test report, auxiliary equipment is defined as equipment which is used temporarily to enable operational and control features especially used for the tests of the EUT which is not used during normal operation or equipment that is used during the tests in combination with the EUT but is not subject of this test report. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Auxiliary Equipment can influence the test results. Device Details Description (Manufacturer, HW, SW, S/N) AC/DC power supply PeakTech, -, -, 081062045 PeakTech 6005D (115 V 60 Hz) 3.6 EUT SETUPS This chapter describes the combination of EUTs and equipment used for testing. The rationale for selecting the EUTs, ancillary and auxiliary equipment and interconnecting cables, is to test a representative configuration meeting the requirements of the referenced standards. Setup Combination of EUTs Description and Rationale evaluation board, Setup for radiated measurement DE1072001aa01 AC/DC power supply TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 11 of 29

3.7 OPERATING MODES This chapter describes the operating modes of the EUTs used for testing. 3.7.1TEST CHANNELS 2.4 GHz ISM WLAN 2400 - 2483.5 MHz 20 MHz Test Channels: low mid high Channel: 1 6 13 Frequency [MHz] 2412 2437 2472 40 MHz Test Channels: low mid high Channel: 3 6 11 Frequency [MHz] 2422 2437 2462 In case of testing another channel, the measurement summary state “additional channel” and the channel or centre frequency of the operating frequency is stated in the test protocol. Duty cycle = 100 % 3.8 PRODUCT LABELLING 3.8.1FCC ID LABEL Please refer to the documentation of the applicant. 3.8.2LOCATION OF THE LABEL ON THE EUT Please refer to the documentation of the applicant. TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 12 of 29

4 TEST RESULTS 4.1 TRANSMITTER SPURIOUS RADIATED EMISSIONS Standard FCC Part 15 Subpart C The test was performed according to: ANSI C63.10 4.1.1TEST DESCRIPTION The test set-up was made in accordance to the general provisions of ANSI C63.10 in a typical installation configuration. The Equipment Under Test (EUT) was set up on a non-conductive table 1.0 x 2.0 m² in the semi-anechoic chamber. The influence of the EUT support table that is used between 30–1000 MHz was evaluated. The measurement procedure is implemented into the EMI test software EMC32 from R&S. Exploratory tests are performed at 3 orthogonal axes to determine the worst-case orientation of a body-worn or handheld EUT. The final test on all kind of EUTs is also performed at 3 axes. A pre-check is performed while the EUT is powered from a DC power source. 1. Measurement up to 30 MHz The Loop antenna HFH2-Z2 is used. Step 1: pre measurement •Anechoic chamber •Antenna distance: 3 m •Detector: Peak-Maxhold •Frequency range: 0.009 - 0.15 MHz and 0.15 – 30 MHz •Frequency steps: 0.05 kHz and 2.25 kHz •IF–Bandwidth: 0.2 kHz and 9 kHz •Measuring time / Frequency step: 100 ms (FFT-based) Intention of this step is, to determine the radiated EMI-profile of the EUT. Afterwards the relevant emissions for the final measurement are identified. Step 2: final measurement For the relevant emissions determined in step 1, an additional measurement with the following settings will be performed. Intention of this step is to find the maximum emission level. •Open area test side •Antenna distance: according to the Standard •Detector: Quasi-Peak •Frequency range: 0.009 – 30 MHz •Frequency steps: measurement at frequencies detected in step 1 •IF–Bandwidth: 0.2 - 10 kHz •Measuring time / Frequency step: 1 s 2. Measurement above 30 MHz and up to 1 GHz Step 1: Preliminary scan This is a preliminary test to identify the highest amplitudes relative to the limit. Settings for step 1: - Antenna distance: 3 m - Detector: Peak-Maxhold / Quasipeak (FFT-based) TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 13 of 29

- Frequency range: 30 – 1000 MHz - Frequency steps: 30 kHz - IF–Bandwidth: 120 kHz - Measuring time / Frequency step: 100 ms - Turntable angle range: –180° to 90° - Turntable step size: 90° - Height variation range: 1 – 3 m - Height variation step size: 2 m - Polarisation: Horizontal + Vertical Intention of this step is, to determine the radiated EMI-profile of the EUT. Afterwards the relevant emissions for the final measurement are identified. Step 2: Adjustment measurement In this step the accuracy of the turntable azimuth and antenna height will be improved. This is necessary to find out the maximum value of every frequency. For each frequency, which was determined the turntable azimuth and antenna height will be adjusted. The turntable azimuth will slowly vary by ± 45° around this value. During this action, the value of emission is continuously measured. The turntable azimuth at the highest emission will be recorded and adjusted. In this position, the antenna height will also slowly vary by ± 100 cm around the antenna height determined. During this action, the value of emission is also continuously measured. The antenna height of the highest emission will also be recorded and adjusted. - Detector: Peak – Maxhold - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 100 ms - Turntable angle range: ± 45 ° around the determined value - Height variation range: ± 100 cm around the determined value - Antenna Polarisation: max. value determined in step 1 Step 3: Final measurement with QP detector With the settings determined in step 3, the final measurement will be performed: EMI receiver settings for step 4: - Detector: Quasi-Peak (< 1 GHz) - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 1 s After the measurement a plot will be generated which contains a diagram with the results of the preliminary scan and a chart with the frequencies and values of the results of the final measurement. 3. Measurement above 1 GHz The following modifications apply to the measurement procedure for the frequency range above 1 GHz: Step 1: The Equipment Under Test (EUT) was set up on a non-conductive support (tilt device) at 1.5 m height in the fully-anechoic chamber. All steps were performed with one height (1.5 m) of the receiving antenna only. The EUT is turned during the preliminary measurement across the elevation axis, with a step size of 90 °. The turn table step size (azimuth angle) for the preliminary measurement is 45 °. Step 2: TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 14 of 29

Due to the fact, that in this frequency range the test is performed in a fully anechoic room, the height scan of the receiving antenna instep 2 is omitted. Instead of this, a maximum search with a step size ± 45° for the elevation axis is performed. The turn table azimuth will slowly vary by ± 22.5°. The elevation angle will slowly vary by ± 45° EMI receiver settings (for all steps): - Detector: Peak, Average - IF Bandwidth = 1 MHz Step 3: Spectrum analyser settings for step 3: - Detector: Peak / Average - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 1 MHz - Measuring time: 1 s 4.1.2TEST REQUIREMENTS / LIMITS FCC Part 15, Subpart C, §15.247 (d) ... In addition, radiated emissions which fall in the restricted bands, as defined in Section 15.205(a), must also comply with the radiated emission limits specified in Section 15.209(a) (see Section 15.205(c)). FCC Part 15, Subpart C, §15.209, Radiated Emission Limits Measurement Frequency in MHz Limit (µV/m) Limits (dBµV/m) distance (m) 0.009 – 0.49 2400/F(kHz)@300m 3 (48.5 – 13.8)@300m 0.49 – 1.705 24000/F(kHz)@30m 3 (33.8 – 23.0)@30m 1.705 – 30 30@30m 3 29.5@30m The measured values are corrected with an inverse linear distance extrapolation factor (40 dB/decade) according FCC 15.31 (2). Measurement Frequency in MHz Limit (µV/m) Limits (dBµV/m) distance (m) 30 – 88 100@3m 3 40.0@3m 88 – 216 150@3m 3 43.5@3m 216 – 960 200@3m 3 46.0@3m 960 - 26000 500@3m 3 54.0@3m 26000 - 40000 500@3m 1 54.0@3m The measured values above 26 GHz are corrected with an inverse linear distance extrapolation factor (20 dB/decade). §15.35(b) ..., there is also a limit on the radio frequency emissions, as measured using instrumentation with a peak detector function, corresponding to 20 dB above the maximum permitted average limit.... Used conversion factor: Limit (dBµV/m) = 20 log (Limit (µV/m)/1µV/m) TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 15 of 29

4.1.3TEST PROTOCOL Ambient 21–25 °C temperature: Air Pressure: 1002–1020 hPa Humidity: 38–45 % WLAN b-Mode; 20 MHz Mode / Ch. Spurious Spurious Detec- RBW Limit Margin Limit Set EUT Center Freq. Level tor [kHz] [dBµV/m] to Limit Type target Freq. [MHz] [dBµV/m] [dB] power [MHz] n-mode, 2472.0 2483.58 57.59 PEAK 1000 74.00 16.41 RB MCS6 / 13 dBm n-mode, 2472.0 2483.91 41.55 AV 1000 54 12.45 RB MCS6 / 13 dBm 4.1.4MEASUREMENT PLOT (SHOWING THE HIGHEST VALUE, “WORST CASE”) Radio Technology = WLAN n-Mode, MCS6 / 13 dBm, 40 MHz, Operating Frequency = HIGH Level in dBµV/m 4.1.5TEST EQUIPMENT USED Radiated Emissions TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 16 of 29

4.2 BAND EDGE COMPLIANCE RADIATED Standard FCC Part 15 Subpart C The test was performed according to: ANSI C63.10 4.2.1TEST DESCRIPTION Please see test description for the test case “Spurious Radiated Emissions” 4.2.2TEST REQUIREMENTS / LIMITS For band edges connected to a restricted band, the limits are specified in Section 15.209(a) FCC Part 15, Subpart C, §15.209, Radiated Emission Limits Measurement Frequency in MHz Limit (µV/m) Limits (dBµV/m) distance (m) 0.009 – 0.49 2400/F(kHz)@300m 3 (48.5 – 13.8)@300m 0.49 – 1.705 24000/F(kHz)@30m 3 (33.8 – 23.0)@30m 1.705 – 30 30@30m 3 29.5@30m The measured values are corrected with an inverse linear distance extrapolation factor (40 dB/decade) according FCC 15.31 (2). Measurement Frequency in MHz Limit (µV/m) Limits (dBµV/m) distance (m) 30 – 88 100@3m 3 40.0@3m 88 – 216 150@3m 3 43.5@3m 216 – 960 200@3m 3 46.0@3m 960 - 26000 500@3m 3 54.0@3m 26000 - 40000 500@3m 1 54.0@3m The measured values above 26 GHz are corrected with an inverse linear distance extrapolation factor (20 dB/decade). §15.35(b) ..., there is also a limit on the radio frequency emissions, as measured using instrumentation with a peak detector function, corresponding to 20 dB above the maximum permitted average limit.... Used conversion factor: Limit (dBµV/m) = 20 log (Limit (µV/m)/1µV/m) TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 17 of 29

4.2.3TEST PROTOCOL Ambient temperature: 21–25 °C Air Pressure: 1002–1020 hPa Humidity: 38–45 % WLAN b-Mode; 20 MHz Mode / Set Ch. Spurious Spurious Detec- RBW Limit Margin Limit EUT target Center Freq. Level tor [kHz] [dBµV/m] to Limit Type power Freq. [MHz] [dBµV/m] [dB] [MHz] b-mode, 2Mbit / 2467.0 2483.93 38.01 AV 1000 54 15.99 RB 15 dBm b-mode, 2Mbit / 2467.0 2483.93 49.55 PEAK 1000 74 24.45 RB 15 dBm g-mode, 9Mbit / 2462.0 2483.85 38.14 AV 1000 54 15.86 RB 13 dBm g-mode, 9Mbit / 2462.0 2483.85 52.76 PEAK 1000 74 21.24 RB 13 dBm g-mode, 2467.0 2483.51 38.94 AV 1000 54 15.06 RB 48Mbit / 9 dBm g-mode, 2467.0 2483.51 53.35 PEAK 1000 74 20.65 RB 48Mbit / 9 dBm n-mode, 2447 2483.93 41.25 AV 1000 54 12.74 RB HT40/MSC0 / 13 dBm n-mode, 2447 2483.93 57.99 PEAK 1000 74 16.01 RB HT40/MSC0 / 13 dBm n-mode, 2447 2483.51 40.15 AV 1000 54 13.85 RB HT40/MSC6 / 13 dBm n-mode, 2447 2483.51 56.77 PEAK 1000 74 17.23 RB HT40/MSC6 / 13 dBm n-mode, 2452 2483.76 40.04 AV 1000 54 13.96 RB HT40/MSC6 / 11 dBm n-mode, 2452 2483.76 54.41 PEAK 1000 74 19.59 RB HT40/MSC6 / 11 dBm n-mode, 2462 2483.76 38.09 AV 1000 54 15.91 RB HT20/MSC6 / 7 dBm n-mode, 2462 2483.76 53.31 PEAK 1000 74 20.69 RB HT40/MSC6 / 7 dBm n-mode 2462 2484.78 38.69 AV 1000 54 15.31 RB HT20/MSC6 / 9 dBm n-mode 2462 2484.78 54.47 PEAK 1000 74 19.53 RB HT20/MSC6 / 9 dBm TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 18 of 29

n-mode 2467 2485.04 39.15 AV 1000 54 14.84 RB HT20/MSC6 / 9 dBm n-mode 2467 2485.04 54.22 PEAK 1000 74 19.78 RB HT20/MSC6 / 9 dBm n-mode 2467 2483.6 40.09 AV 1000 54 13.91 RB HT20/MSC6 / 10 dBm n-mode 2467 2483.6 53.32 PEAK 1000 74 20.68 RB HT20/MSC6 / 10 dBm Remark: Antenna port of EUT terminated with 50 Ohm. 4.2.4MEASUREMENT PLOT (SHOWING THE HIGHEST VALUE, “WORST CASE”) Level in dBµV/m 4.2.5TEST EQUIPMENT USED Radiated Emissions TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 19 of 29

5 TEST EQUIPMENT 1 Radiated Emissions Lab to perform radiated emission tests Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 1.1 NRV-Z1 Sensor Head A Rohde & Schwarz 827753/005 2017-05 2018-05 1.2 MFS Rubidium Datum GmbH 002 2017-10 2018-10 Frequency Normal MFS 1.3 Opus10 TPR ThermoAirpres Lufft Mess- und 13936 2017-04 2019-04 (8253.00) sure Regeltechnik GmbH Datalogger 13 (Environ) 1.4 Anechoic 10.58 x 6.38 x Frankonia none 2016-05 2019-05 Chamber 6.00 m³ 1.5 HL 562 Ultralog new Rohde & Schwarz 830547/003 2015-06 2018-06 biconicals 1.6 5HC2700/12750 High Pass Trilithic 9942012 -1.5-KK Filter 1.7 ASP 1.2/1.8-10 Antenna Mast Maturo GmbH - kg 1.8 Fully Anechoic 8.80m x Albatross Projects P26971-647-001- 2015-06 2018-06 Room 4.60m x PRB 4.05m (l x w x h) 1.9 Fluke 177 Digital Fluke Europe B.V. 86670383 2016-02 2018-02 Multimeter 03 (Multimeter) 1.10 JS4-18002600- Broadband Miteq 849785 32-5P Amplifier 18 GHz - 26 GHz 1.11 FSW 43 Spectrum Rohde & Schwarz 103779 2016-12 2018-12 Analyzer 1.12 3160-09 Standard Gain EMCO Elektronic 00083069 / Pyramidal GmbH Horn Antenna 26.5 GHz 1.13 WHKX 7.0/18G- High Pass Wainwright 09 8SS Filter 1.14 4HC1600/12750 High Pass Trilithic 9942011 -1.5-KK Filter 1.15 Chroma 6404 AC Power Chroma ATE INC. 64040001304 Source 1.16 JS4-00102600- Broadband Miteq 619368 42-5A Amplifier 30 MHz - 26 GHz 1.17 TT 1.5 WI Turn Table Maturo GmbH - 1.18 HL 562 Ultralog Log.-per. Rohde & Schwarz 100609 2016-04 2019-04 Antenna 1.19 3160-10 Standard Gain EMCO Elektronic 00086675 / Pyramidal GmbH Horn Antenna 40 GHz 1.20 5HC3500/18000 High Pass Trilithic 200035008 -1.2-KK Filter TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 20 of 29

Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 1.21 HFH2-Z2 Loop Antenna Rohde & Schwarz 829324/006 2014-11 2017-11 1.22 Opus10 THI ThermoHygro Lufft Mess- und 12482 2017-03 2019-03 (8152.00) Datalogger 12 Regeltechnik GmbH (Environ) 1.23 ESR 7 EMI Receiver / Rohde & Schwarz 101424 2016-11 2018-11 Spectrum Analyzer 1.24 JS4-00101800- Broadband Miteq 896037 35-5P Amplifier 30 MHz - 18 GHz 1.25 AS 620 P Antenna mast HD GmbH 620/37 1.26 Tilt device Antrieb TD1.5- Maturo GmbH TD1.5- Maturo 10kg 10kg/024/37907 (Rohacell) 09 1.27 ESIB 26 Spectrum Rohde & Schwarz 830482/004 2015-12 2017-12 Analyzer 1.28 PAS 2.5 - 10 kg Antenna Mast Maturo GmbH - 1.29 AM 4.0 Antenna mast Maturo GmbH AM4.0/180/1192 0513 1.30 HF 907 Double-ridged Rohde & Schwarz 102444 2015-05 2018-05 horn The calibration interval is the time interval between “Last Calibration” and “Calibration Due” TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 21 of 29

6 ANTENNA FACTORS, CABLE LOSS AND SAMPLE CALCULATIONS This chapter contains the antenna factors with their corresponding path loss of the used measurement path for all antennas as well as the insertion loss of the LISN. 6.1 LISN R&S ESH3-Z5 (150 KHZ – 30 MHZ) cable LISN loss insertion (incl. 10 loss dB ESH3- atten- Frequency Corr. Z5 uator) MHz dB dB dB 0,15 10,1 0,1 10,0 5 10,3 0,1 10,2 7 10,5 0,2 10,3 10 10,5 0,2 10,3 12 10,7 0,3 10,4 14 10,7 0,3 10,4 16 10,8 0,4 10,4 18 10,9 0,4 10,5 20 10,9 0,4 10,5 22 11,1 0,5 10,6 24 11,1 0,5 10,6 26 11,2 0,5 10,7 28 11,2 0,5 10,7 30 11,3 0,5 10,8 Sample calculation ULISN (dB µV) = U (dB µV) + Corr. (dB) U = Receiver reading LISN Insertion loss = Voltage Division Factor of LISN Corr. = sum of single correction factors of used LISN, cables, switch units (if used) Linear interpolation will be used for frequencies in between the values in the table. TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 22 of 29

6.2 ANTENNA R&S HFH2-Z2 (9 KHZ – 30 MHZ) cable cable cable cable distance dLimit dused loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. AF (inside (outside (switch (to (-40 dB/ distance distance Frequency HFH-Z2) Corr. chamber) chamber) unit) receiver) decade) (limit) (used) MHz dB (1/m) dB dB dB dB dB dB m m 0,009 20,50 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,01 20,45 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,015 20,37 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,02 20,36 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,025 20,38 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,03 20,32 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,05 20,35 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,08 20,30 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,1 20,20 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,2 20,17 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,3 20,14 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,49 20,12 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,490001 20,12 -39,6 0,1 0,1 0,1 0,1 -40 30 3 0,5 20,11 -39,6 0,1 0,1 0,1 0,1 -40 30 3 0,8 20,10 -39,6 0,1 0,1 0,1 0,1 -40 30 3 1 20,09 -39,6 0,1 0,1 0,1 0,1 -40 30 3 2 20,08 -39,6 0,1 0,1 0,1 0,1 -40 30 3 3 20,06 -39,6 0,1 0,1 0,1 0,1 -40 30 3 4 20,05 -39,5 0,2 0,1 0,1 0,1 -40 30 3 5 20,05 -39,5 0,2 0,1 0,1 0,1 -40 30 3 6 20,02 -39,5 0,2 0,1 0,1 0,1 -40 30 3 8 19,95 -39,5 0,2 0,1 0,1 0,1 -40 30 3 10 19,83 -39,4 0,2 0,1 0,2 0,1 -40 30 3 12 19,71 -39,4 0,2 0,1 0,2 0,1 -40 30 3 14 19,54 -39,4 0,2 0,1 0,2 0,1 -40 30 3 16 19,53 -39,3 0,3 0,1 0,2 0,1 -40 30 3 18 19,50 -39,3 0,3 0,1 0,2 0,1 -40 30 3 20 19,57 -39,3 0,3 0,1 0,2 0,1 -40 30 3 22 19,61 -39,3 0,3 0,1 0,2 0,1 -40 30 3 24 19,61 -39,3 0,3 0,1 0,2 0,1 -40 30 3 26 19,54 -39,3 0,3 0,1 0,2 0,1 -40 30 3 28 19,46 -39,2 0,3 0,1 0,3 0,1 -40 30 3 30 19,73 -39,1 0,4 0,1 0,3 0,1 -40 30 3 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) distance correction = -40 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 23 of 29

6.3 ANTENNA R&S HL562 (30 MHZ – 1 GHZ) (dLimit = 3 m) cable cable cable cable distance dLimit dused AF loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. R&S (inside (outside (switch (to (-20 dB/ distance distance Frequency HL562 Corr. chamber) chamber) unit) receiver) decade) (limit) (used) MHz dB (1/m) dB dB dB dB dB dB m m 30 18,6 0,6 0,29 0,04 0,23 0,02 0,0 3 3 50 6,0 0,9 0,39 0,09 0,32 0,08 0,0 3 3 100 9,7 1,2 0,56 0,14 0,47 0,08 0,0 3 3 150 7,9 1,6 0,73 0,20 0,59 0,12 0,0 3 3 200 7,6 1,9 0,84 0,21 0,70 0,11 0,0 3 3 250 9,5 2,1 0,98 0,24 0,80 0,13 0,0 3 3 300 11,0 2,3 1,04 0,26 0,89 0,15 0,0 3 3 350 12,4 2,6 1,18 0,31 0,96 0,13 0,0 3 3 400 13,6 2,9 1,28 0,35 1,03 0,19 0,0 3 3 450 14,7 3,1 1,39 0,38 1,11 0,22 0,0 3 3 500 15,6 3,2 1,44 0,39 1,20 0,19 0,0 3 3 550 16,3 3,5 1,55 0,46 1,24 0,23 0,0 3 3 600 17,2 3,5 1,59 0,43 1,29 0,23 0,0 3 3 650 18,1 3,6 1,67 0,34 1,35 0,22 0,0 3 3 700 18,5 3,6 1,67 0,42 1,41 0,15 0,0 3 3 750 19,1 4,1 1,87 0,54 1,46 0,25 0,0 3 3 800 19,6 4,1 1,90 0,46 1,51 0,25 0,0 3 3 850 20,1 4,4 1,99 0,60 1,56 0,27 0,0 3 3 900 20,8 4,7 2,14 0,60 1,63 0,29 0,0 3 3 950 21,1 4,8 2,22 0,60 1,66 0,33 0,0 3 3 1000 21,6 4,9 2,23 0,61 1,71 0,30 0,0 3 3 (dLimit = 10 m) 30 18,6 -9,9 0,29 0,04 0,23 0,02 -10,5 10 3 50 6,0 -9,6 0,39 0,09 0,32 0,08 -10,5 10 3 100 9,7 -9,2 0,56 0,14 0,47 0,08 -10,5 10 3 150 7,9 -8,8 0,73 0,20 0,59 0,12 -10,5 10 3 200 7,6 -8,6 0,84 0,21 0,70 0,11 -10,5 10 3 250 9,5 -8,3 0,98 0,24 0,80 0,13 -10,5 10 3 300 11,0 -8,1 1,04 0,26 0,89 0,15 -10,5 10 3 350 12,4 -7,9 1,18 0,31 0,96 0,13 -10,5 10 3 400 13,6 -7,6 1,28 0,35 1,03 0,19 -10,5 10 3 450 14,7 -7,4 1,39 0,38 1,11 0,22 -10,5 10 3 500 15,6 -7,2 1,44 0,39 1,20 0,19 -10,5 10 3 550 16,3 -7,0 1,55 0,46 1,24 0,23 -10,5 10 3 600 17,2 -6,9 1,59 0,43 1,29 0,23 -10,5 10 3 650 18,1 -6,9 1,67 0,34 1,35 0,22 -10,5 10 3 700 18,5 -6,8 1,67 0,42 1,41 0,15 -10,5 10 3 750 19,1 -6,3 1,87 0,54 1,46 0,25 -10,5 10 3 800 19,6 -6,3 1,90 0,46 1,51 0,25 -10,5 10 3 850 20,1 -6,0 1,99 0,60 1,56 0,27 -10,5 10 3 900 20,8 -5,8 2,14 0,60 1,63 0,29 -10,5 10 3 950 21,1 -5,6 2,22 0,60 1,66 0,33 -10,5 10 3 1000 21,6 -5,6 2,23 0,61 1,71 0,30 -10,5 10 3 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) distance correction = -20 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Tables show an extract of values. TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 24 of 29

6.4 ANTENNA R&S HF907 (1 GHZ – 18 GHZ) cable cable loss 3 loss 1 (switch (relay + cable unit, AF cable loss 2 atten- cable R&S inside (outside uator & loss 4 (to Frequency HF907 Corr. chamber) chamber) pre-amp) receiver) MHz dB (1/m) dB dB dB dB dB 1000 24,4 -19,4 0,99 0,31 -21,51 0,79 2000 28,5 -17,4 1,44 0,44 -20,63 1,38 3000 31,0 -16,1 1,87 0,53 -19,85 1,33 4000 33,1 -14,7 2,41 0,67 -19,13 1,31 5000 34,4 -13,7 2,78 0,86 -18,71 1,40 6000 34,7 -12,7 2,74 0,90 -17,83 1,47 7000 35,6 -11,0 2,82 0,86 -16,19 1,46 cable loss 4 cable (switch loss 1 cable cable unit, used AF (relay loss 2 loss 3 atten- cable for R&S inside (inside (outside uator & loss 5 (to FCC Frequency HF907 Corr. chamber) chamber) chamber) pre-amp) receiver) 15.247 MHz dB (1/m) dB dB dB dB dB dB 3000 31,0 -23,4 0,47 1,87 0,53 -27,58 1,33 4000 33,1 -23,3 0,56 2,41 0,67 -28,23 1,31 5000 34,4 -21,7 0,61 2,78 0,86 -27,35 1,40 6000 34,7 -21,2 0,58 2,74 0,90 -26,89 1,47 7000 35,6 -19,8 0,66 2,82 0,86 -25,58 1,46 cable loss 1 cable cable cable cable cable AF (relay loss 2 loss 3 loss 4 loss 5 loss 6 R&S inside (High (pre- (inside (outside (to Frequency HF907 Corr. chamber) Pass) amp) chamber) chamber) receiver) MHz dB (1/m) dB dB dB dB dB dB dB 7000 35,6 -57,3 0,56 1,28 -62,72 2,66 0,94 1,46 8000 36,3 -56,3 0,69 0,71 -61,49 2,84 1,00 1,53 9000 37,1 -55,3 0,68 0,65 -60,80 3,06 1,09 1,60 10000 37,5 -56,2 0,70 0,54 -61,91 3,28 1,20 1,67 11000 37,5 -55,3 0,80 0,61 -61,40 3,43 1,27 1,70 12000 37,6 -53,7 0,84 0,42 -59,70 3,53 1,26 1,73 13000 38,2 -53,5 0,83 0,44 -59,81 3,75 1,32 1,83 14000 39,9 -56,3 0,91 0,53 -63,03 3,91 1,40 1,77 15000 40,9 -54,1 0,98 0,54 -61,05 4,02 1,44 1,83 16000 41,3 -54,1 1,23 0,49 -61,51 4,17 1,51 1,85 17000 42,8 -54,4 1,36 0,76 -62,36 4,34 1,53 2,00 18000 44,2 -54,7 1,70 0,53 -62,88 4,41 1,55 1,91 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. Tables show an extract of values. TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 25 of 29

6.5 ANTENNA EMCO 3160-09 (18 GHZ – 26.5 GHZ) cable cable cable cable cable AF loss 1 loss 2 loss 3 loss 4 loss 5 EMCO (inside (pre- (inside (switch (to Frequency 3160-09 Corr. chamber) amp) chamber) unit) receiver) MHz dB (1/m) dB dB dB dB dB dB 18000 40,2 -23,5 0,72 -35,85 6,20 2,81 2,65 18500 40,2 -23,2 0,69 -35,71 6,46 2,76 2,59 19000 40,2 -22,0 0,76 -35,44 6,69 3,15 2,79 19500 40,3 -21,3 0,74 -35,07 7,04 3,11 2,91 20000 40,3 -20,3 0,72 -34,49 7,30 3,07 3,05 20500 40,3 -19,9 0,78 -34,46 7,48 3,12 3,15 21000 40,3 -19,1 0,87 -34,07 7,61 3,20 3,33 21500 40,3 -19,1 0,90 -33,96 7,47 3,28 3,19 22000 40,3 -18,7 0,89 -33,57 7,34 3,35 3,28 22500 40,4 -19,0 0,87 -33,66 7,06 3,75 2,94 23000 40,4 -19,5 0,88 -33,75 6,92 3,77 2,70 23500 40,4 -19,3 0,90 -33,35 6,99 3,52 2,66 24000 40,4 -19,8 0,88 -33,99 6,88 3,88 2,58 24500 40,4 -19,5 0,91 -33,89 7,01 3,93 2,51 25000 40,4 -19,3 0,88 -33,00 6,72 3,96 2,14 25500 40,5 -20,4 0,89 -34,07 6,90 3,66 2,22 26000 40,5 -21,3 0,86 -35,11 7,02 3,69 2,28 26500 40,5 -21,1 0,90 -35,20 7,15 3,91 2,36 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values. TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 26 of 29

6.6 ANTENNA EMCO 3160-10 (26.5 GHZ – 40 GHZ) cable cable cable cable distance dLimit dused AF loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. EMCO (inside (outside (switch (to (-20 dB/ distance distance Frequency 3160-10 Corr. chamber) chamber) unit) receiver) decade) (limit) (used) GHz dB (1/m) dB dB dB dB dB dB m m 26,5 43,4 -11,2 4,4 -15,6 3 0,5 27,0 43,4 -11,2 4,4 -15,6 3 0,5 28,0 43,4 -11,1 4,5 -15,6 3 0,5 29,0 43,5 -11,0 4,6 -15,6 3 0,5 30,0 43,5 -10,9 4,7 -15,6 3 0,5 31,0 43,5 -10,8 4,7 -15,6 3 0,5 32,0 43,5 -10,7 4,8 -15,6 3 0,5 33,0 43,6 -10,7 4,9 -15,6 3 0,5 34,0 43,6 -10,6 5,0 -15,6 3 0,5 35,0 43,6 -10,5 5,1 -15,6 3 0,5 36,0 43,6 -10,4 5,1 -15,6 3 0,5 37,0 43,7 -10,3 5,2 -15,6 3 0,5 38,0 43,7 -10,2 5,3 -15,6 3 0,5 39,0 43,7 -10,2 5,4 -15,6 3 0,5 40,0 43,8 -10,1 5,5 -15,6 3 0,5 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolarisation will be used for frequencies in between the values in the table. distance correction = -20 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values. TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 27 of 29

7 SETUP DRAWINGS Drawing 1: Setup in the anechoic chamber. For measurements below 1 GHz the ground was replaced by a conducting ground plane. Rubidium Spectrum OUT Frequency Analyser (object Standard Shielded RF cable under test) Drawing 2: Setup for conducted radio tests. TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 28 of 29

8 MEASUREMENT UNCERTAINTIES Test Case Parameter Uncertainty AC Power Line Power ± 3.4 dB Field Strength of spurious radiation Power ± 5.5 dB 6 dB / 26 dB / 99% Bandwidth Power ± 2.9 dB Frequency ± 11.2 kHz Conducted Output Power Power ± 2.2 dB Band Edge Compliance Power ± 2.2 dB Frequency ± 11.2 kHz Frequency Stability Frequency ± 25 Hz Power Spectral Density Power ± 2.2 dB 9 PHOTO REPORT Please see separate photo report. TEST REPORT REFERENCE: MDE_LESSW_1701_FCCa Page 29 of 29


Document Created: 2018-03-22 17:34:33
Document Modified: 2018-03-22 17:34:33
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC