MDE_UBLOX_1551_FCCe_Rev.1_15.225_2016-04-01_SIGNED

FCC ID: XPYEMMYW161

Test Report

Download: PDF
FCCID_3109665

FCC Measurement/Technical Report on WLAN/Bluetooth/NFC module EMMY-W161 and EMMY-W163 NFC part Re por t Re fe r e n ce : MDE_UBLOX_1551_FCCe_Rev.1 FCC ID: EMMY-W161: XPYEMMYW161 EMMY-W163: XPYEMMYW163 IC ID: EMMY-W161: 8595A-EMMYW161 EMMY-W163: 8595A-EMMYW163 Te st La bora t or y : 7layers GmbH Borsigstrasse 11 40880 Ratingen Germany Note: The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts without the written approval of the test laboratory. 7 la ye r s Gm bH Geschäftsführer/ Borsigstraße 11 Managing Directors: Registergericht/registered: a Bureau Verit as 40880 Ratingen, Germany Frank Spiller Düsseldorf HRB 75554 Group Com pany T +49 (0) 2102 749 0 Bernhard Retka USt-Id.-Nr./VAT-No. DE203159652 F +49 (0) 2102 749 350 Alexandre Norré-Oudard Steuer-Nr./TAX-No. 147/5869/0385 www.7layers.com Commerzbank AG Account No. 303 016 000 Bank Code 300 400 00 IBAN DE81 3004 0000 0303 0160 00 Swift Code COBADEFF

Ta ble of Con t e n t s 0 Su m m a r y 3 0.1 Technical Report Summary 3 0.2 Measurement Summary 4 Re vision H ist or y 4 1 Adm in ist r a t ive D a t a 5 1.1 Testing Laboratory 5 1.2 Project Data 5 1.3 Applicant Data 5 1.4 Manufacturer Data 5 2 Te st obj e ct D a t a 6 2.1 General EUT Description 6 2.2 EUT Main components 7 2.3 Ancillary Equipment 7 2.4 Auxiliary Equipment 7 2.5 EUT Setups 8 2.6 Operating Modes 8 2.7 Special software used for testing 8 2.8 Product labelling 8 3 Te st Re su lt s 9 3.1 Conducted Emissions AC Power line 9 3.2 Spurious radiated emissions 12 3.3 Occupied bandwidth 16 3.4 Spectrum mask 17 3.5 Frequency tolerance 18 4 Te st Equ ipm e n t 21 5 Ph ot o Re por t 23 6 Se t u p D r a w in gs 23 7 FCC a n d I C Cor r e la t ion of m e a su r e m e n t r e qu ir e m e n t s 2 4 8 An n e x m e a su r e m e n t plot s 25 8.1 Radiated emissions 25 8.2 AC Mains conducted 27 8.3 Occupied bandwidth 29 8.4 Spectrum mask 30 Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 2 of 30

0 Su m m a r y 0 .1 Te ch n ica l Re por t Su m m a r y Type of Aut h or iza t ion Certification for an intentional radiator operating at 13.56 MHz Applica ble FCC Ru le s Prepared in accordance with the requirements of FCC Rules and Regulations as listed in 47 CFR Ch.1 Parts 2 (10-1-15 Edition) and 15 (10-1-15 Edition). The following subparts are applicable to the results in this test report. Part 2, Subpart J - Equipment Authorization Procedures, Certification Part 15, Subpart C – Intentional Radiators § 15.205 Restricted bands of operation § 15.207 Conducted limits § 15.209 Radiated emission limits; general requirements § 15.215 Additional provisions to the general radiated emission limitations § 15.225 Operation within the band 13.110-14.010 MHz ANSI C63.10-2013 is applied Sum m a r y Te st Re su lt s: Th e EUT com plie d w it h a ll pe r for m e d t e st s a s list e d in ch a pt e r 0 .2 M e a sur e m e n t Sum m a r y. Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 3 of 30

0 .2 M e a su r e m e n t Su m m a r y FCC Pa r t 1 5 , Subpa r t C § 1 5 .2 0 7 Conducted Emissions AC Power line The measurement was performed according to ANSI C63.10 2013 OP- M ode Se t up Por t Fina l Re sult op-mode 1 Setup_01 DC power supply passed FCC Pa r t 1 5 , Subpa r t C § 1 5 .2 0 9 Radiated Emissions The measurement was performed according to ANSI C63.10 2013 OP- M ode Se t up Por t Fina l Re sult op-mode 1 Setup_01 NFC antenna passed FCC Pa r t 1 5 , Subpa r t C § 1 5 .2 1 5 Occupied Bandwidth The measurement was performed according to ANSI C63.10 2013 OP- M ode Se t up Por t Fina l Re sult op-mode 1 Setup_02 NFC antenna passed FCC Pa r t 1 5 , Subpa r t C § 1 5 .2 2 5 Spectrum Mask The measurement was performed according to ANSI C63.10 2013 OP- M ode Se t up Por t Fina l Re sult op-mode 1 Setup_01 NFC antenna passed FCC Pa r t 1 5 , Subpa r t C § 1 5 .2 2 5 Frequency Tolerance The measurement was performed according to ANSI C63.10 2013 OP- M ode Se t up Por t Fina l Re sult op-mode 2 Setup_01 NFC antenna passed Re vision H ist or y Re por t ve r sion con t r ol Ve r sion Re le a se da t e Ch a n ge D e scr ipt ion Ve r sion va lidit y initial 2016-03-30 -- invalid Rev.1 2016-04-01 Page 1: Change of FCC ID and IC ID. valid Page 7: Change of Type Designation from W161 to EMMY-W161 and W163 to EMMY-W163. WOLFGANG PETER RICHTER DOBRIN TODOROV DOBRINOV Responsible for 2016.04.01 18:19:41 Responsible 2016.04.01 18:15:47 +02'00' +02'00' Accreditation Scope: for Test Report: Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 4 of 30

1 Adm in ist r a t ive D a t a 1 .1 Te st in g La bor a t or y Company Name: 7layers GmbH Address Borsigstr. 11 40880 Ratingen Germany This facility has been fully described in a report submitted to the FCC and accepted under the registration number 96716. The test facility is also accredited by the following accreditation organisation: Laboratory accreditation no.: DAkkS D-PL-12140-01-01 Responsible for Accreditation Scope: Dipl.-Ing. Bernhard Retka Dipl.-Ing. Robert Machulec Dipl.-Ing. Andreas Petz Dipl.-Ing. Marco Kullik Dipl.-Ing. Wolfgang Richter Report Template Version: 2015-08-24 1 .2 Pr oj e ct D a t a Responsible for testing and report: Dipl.-Ing. Dobrin Dobrinov Date of Test(s): 2016-01-04 to 2016-01-12 Date of Report: 2016-04-01 1 .3 Applica n t D a t a Company Name: u-blox AG Address: Zürcherstrasse 68 8800 Thalwil Switzerland Contact Person: Mr. Giulio Comar 1 .4 M a n u fa ct u r e r D a t a Company Name: please see applicant data Address: Contact Person: Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 5 of 30

2 Te st obj e ct D a t a 2 .1 Ge n e r a l EUT D e scr ipt ion Equ ipm e n t u n de r Te st WLAN/Bluetooth/NFC module Type D e sign a t ion : EMMY-W161 and EMMY-W163 Kin d of D e vice : NFC transceiver at 13.56 MHz ( opt iona l) Volt a ge Type : DC Volt a ge le ve l: 3.3 V Ge n e r a l pr odu ct de scr ipt ion : EMMY-W161 and EMMY-W163 are ultra-compact multi-radio modules providing Wi-Fi, Classic Bluetooth, Bluetooth low energy and NFC mode of operation. It is designed for both simultaneous and independent operations of: • Wi-Fi IEEE 802.11ac and a/b/g/n • Dual-mode Bluetooth 4.2 • NFC Spe cific pr odu ct de scr ipt ion for t h e EUT: EMMY-W161: Shielded module, single antenna pin for WLAN 802.11 ac/a/b/g/n and Bluetooth communication EMMY-W163: Shielded module, separate antenna pins for WLAN 802.11 ac/a/b/g/n and Bluetooth communication According to the applicant, there is no difference between the two modules, regarding NFC parameters and functionality. Th e EUT pr ovide s t h e follow in g por t s: Por t s - DC power supply - NFC antenna Th e m a in com pon e n t s of t h e EUT a r e list e d a nd de scr ibe d in Cha pt e r 2 .2 . Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 6 of 30

2 .2 EUT M a in com pon e n t s Type , S/ N , Sh or t D e scr ipt ion s e t c. u se d in t h is Te st Re por t Sh or t Equ ipm e n t Type Se r ia l N o. H W St a t u s SW St a t u s D a t e of D e scr ipt ion u n de r Te st D e sign a t ion Re ce ipt EUT A RFID EMMY-W161 ‒ 03 n/a 2015-12-08 (Code: transceiver DE1015031aa01) Remark: EUT A is connected to evaluation board equipped with PCB loop antenna. EUT B RFID EMMY-W163 ‒ 03 n/a 2015-12-08 (Code: transceiver DE1015032ca01) Remark: EUT B is connected to evaluation board equipped with PCB loop antenna. N OTE: Th e sh or t de scr ipt ion is u se d t o sim plify t h e ide n t ifica t ion of t h e EUT in t h is t e st r e por t . 2 .3 An cilla r y Equ ipm e n t For the purposes of this test report, ancillary equipment is defined as equipment which is used in conjunction with the EUT to provide operational and control features to the EUT. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Ancillary Equipment can influence the test results. Sh or t Equ ipm e n t Type Se r ia l N o. H W St a t u s SW St a t u s FCC I D D e scr ipt ion u n de r Te st D e sign a t ion ‒ ‒ ‒ ‒ ‒ ‒ ‒ 2 .4 Au x ilia r y Equ ipm e n t For the purposes of this test report, auxiliary equipment is defined as equipment which is used temporarily to enable operational and control features especially used for the tests of the EUT which is not used during normal operation or equipment that is used during the tests in combination with the EUT but is not subject of this test report. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Auxiliary Equipment can influence the test results. Sh or t Equ ipm e n t Type Se r ia l n o. H W St a t u s SW St a t u s FCC I D D e scr ipt ion u n de r Te st D e sign a t ion AUX 1 Laptop Acer 8210205723 - Linux - Mod: LD1 AUX 2 AC/DC Liteon 8312774105 Rev:A05 - - adapter Technology Corporation AUX 3 Evaluation EVB-EMMY- 02 n/a - board 161 AUX 4 AC/DC PeakTech 081062045 - - - power 6005D supply Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 7 of 30

2 .5 EUT Se t u ps This chapter describes the combination of EUTs and equipment used for testing. The rationale for selecting the EUTs, ancillary and auxiliary equipment and interconnecting cables, is to test a representative configuration meeting the requirements of the referenced standards. Se t u p N o. Com bin a t ion of EUTs D e scr ipt ion a n d Ra t ion a le Setup_01 EUT A + AUX 4 Setup for Frequency Tolerance, Spectrum Mask, AC Power Line and Occupied BW tests Setup_02 EUT B + AUX 4 Setup for Spurious Emissions tests 2 .6 Ope r a t in g M ode s This chapter describes the operating modes of the EUTs used for testing. Op. M ode D e scr ipt ion of Ope r a t in g M ode s Re m a r k s op-mode 1 modulated carrier signal EUT is transmitting a periodic modulated signal and is continuously reading TAG information. op-mode 2 CW carrier signal EUT is transmitting a non-modulated signal 2 .7 Spe cia l soft w a r e u se d for t e st in g Using AUX 1 to AUX 3 and a Marvell software provided by the applicant, it is possible to set the EUT operating modes. 2 .8 Pr odu ct la be llin g 2 .8 .1 FCC I D la be l Please refer to the customer documentation. 2 .8 .2 I C I D la be l Please refer to the customer documentation. 2 .8 .3 Loca t ion of t h e la be l on t he EUT Please refer to the customer documentation. Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 8 of 30

3 Te st Re su lt s 3 .1 Con du ct e d Em ission s AC Pow e r lin e St a n da r d FCC Part 15, 10-1-15 Edition Subpart C Th e t e st w a s pe r for m e d a ccor din g t o: ANSI C63.10–2013 + KDB 174176 D01 3 .1 .1 Te st D e scr ipt ion The test set-up was made in accordance to the general provisions of ANSI C 63.10 The Equipment Under Test (EUT) was setup in a shielded room to perform the conducted emissions measurements in a typical installation configuration. The EUT was powered from 50µH || 50 Ohm Line Impedance Stabilization Network (LISN). The LISN’s unused connections were terminated with 50 Ohm loads. The measurement procedure consists of two steps. It is implemented into the EMI test software EMC-32 from R&S. St e p 1 : Pr e lim ina r y sca n Intention of this step is, to determine the conducted EMI-profile of the EUT. EMI receiver settings: - Detector: Peak – Maxhold & Average - Frequency range: 150 kHz – 30 MHz - Frequency steps: 2.5 kHz - IF–Bandwidth: 9 kHz - Measuring time / Frequency step: 100 ms (FFT-based) - Measurement on phase + neutral lines of the power cords On basis of this preliminary scan the highest amplitudes and the corresponding frequencies relative to the limit are identified. Emissions above the limit and emissions which are in the 10 dB range below the limit are considered. St e p 2 : Fina l m e a su r e m e n t Intention of this step is, to determine the highest emissions with the settings defined in the test specification for the frequencies identified in step 1. EMI receiver settings: - Detector: Quasi-Peak - IF Bandwidth: 9 kHz - Measuring time: 1 s / frequency At each frequency determined in step 1, four measurements are performed in the following combinations: 1) Neutral lead - reference ground (PE grounded) 2) Phase lead - reference ground (PE grounded) 3) Neutral lead - reference ground (PE floating) 4) Phase lead - reference ground (PE floating) The highest value is reported. Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 9 of 30

KD B 1 7 4 1 7 6 D 0 1 , Q5 . D e vice s Ope r a t ing Be low 3 0 M H z For a device with a permanent or detachable antenna operating at or below 30 MHz, the FCC will accept measurements performed with a suitable dummy load in lieu of the antenna under the following conditions: (1) perform the AC power-line conducted tests with the antenna connected to determine compliance with Section 15.207 limits outside the transmitter's fundamental emission band; (2) retest with a dummy load in lieu of the antenna to determine compliance with Section 15.207 limits within the transmitter's fundamental emission band. For a detachable antenna, remove the antenna and connect a suitable dummy load to the antenna connector. For a permanent antenna, remove the antenna and terminate the RF output with a dummy load or network which simulates the antenna in the fundamental frequency band. 3 .1 .2 Te st Re qu ir e m e n t s / Lim it s FCC Part 15, Subpart C, §15.207 Frequency Range (MHz) QP Limit (dBµV) AV Limit (dBµV) 0.15 – 0.5 66 to 56 56 to 46 0.5 – 5 56 46 5 – 30 60 50 Used conversion factor: Limit (dBµV) = 20 log (Limit (µV)/1µV). Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 10 of 30

3 .1 .3 Te st Pr ot ocol Temperature: 23 °C Air Pressure: 1010 hPa Humidity: 35 % Op. M ode Se t up Por t op-mode 1 Setup_01 DC Port (power line) Measurements are performed according to KDB 174176 D01 Step (1). Measurements performed with the EUT dedicated antenna Frequency QuasiPeak Average Limit Margin Line PE (MHz) (dBµV) (dBµV) (dBµV) (dB) 13.454250 48.64 --- 60.00 11.36 L1 GND 13.560000 --- 62.59 50.00 -12.59 N GND 13.560000 62.89 --- 60.00 -2.89 N GND 13.665750 49.04 --- 60.00 10.96 N GND Step (2). Measurements provided with a dummy antenna Frequency QuasiPeak Average Limit Margin Line PE (MHz) (dBµV) (dBµV) (dBµV) (dB) 0.217500 --- 23.31 52.91 29.61 L1 GND 0.339000 23.36 --- 59.23 35.87 N GND 13.348500 --- 24.65 50.00 25.35 L1 GND 13.454250 --- 22.30 50.00 27.70 L1 GND 13.454250 27.39 --- 60.00 32.61 N GND 13.560000 --- 41.43 50.00 8.57 L1 GND 13.560000 41.57 --- 60.00 18.43 N GND 13.665750 27.40 --- 60.00 32.60 N GND 13.665750 --- 22.26 50.00 27.74 L1 GND 13.771500 --- 24.43 50.00 25.57 L1 GND 23.583750 --- 27.86 50.00 22.14 N GND 26.907000 --- 29.66 50.00 20.34 L1 FLO 27.120750 46.86 --- 60.00 13.14 L1 FLO 27.120750 --- 46.55 50.00 3.45 L1 FLO 27.332250 --- 29.58 50.00 20.42 N FLO Remark: Please see annex for the measurement plots. The conducted emission found in the tables above corresponds clearly to the fixed transmitter frequency of the EUT. It was determined that this emission on the AC mains is based on radiated coupling into the test setup. Therefore, for the assessment of the test result, the fixed transmitter frequency of the EUT is not considered. The chosen operating mode is selected as representative mode to generate “worst-case” conditions, i.e. high power consumption. Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 11 of 30

3 .2 Spu r iou s r a dia t e d e m ission s St a n da r d FCC Part 15, 10-1-11 Edition Subpart C Th e t e st w a s pe r for m e d a ccor din g t o: ANSI C63.10–2013 3 .2 .1 Te st D e scr ipt ion The test set-up was made in accordance to the general provisions of ANSI C63.10 in a typical installation configuration. The Equipment Under Test (EUT) was set up on a non- conductive table 1.0 x 2.0 m² in the semi-anechoic chamber. The influence of the EUT support table that is used between 30–1000 MHz was evaluated. The measurement procedure is implemented into the EMI test software EMC32 from R&S. Exploratory tests are performed at 3 orthogonal axes to determine the worst-case orientation of a body-worn or handheld EUT. The final test on all kind of EUTs is also performed at 3 axes. A pre-check is performed while the EUT is powered from a DC power source. 1 . M e a su r e m e n t u p t o 3 0 M H z The Loop antenna HFH2-Z2 is used. St e p 1 : pre measurement  Anechoic chamber  Antenna distance: 3 m  Detector: Peak-Maxhold  Frequency range: 0.009 - 0.15 MHz and 0.15 – 30 MHz  Frequency steps: 0.05 kHz and 2.25 kHz  IF–Bandwidth: 0.2 kHz and 9 kHz  Measuring time / Frequency step: 100 ms (FFT-based) Intention of this step is, to determine the radiated EMI-profile of the EUT. Afterwards the relevant emissions for the final measurement are identified. St e p 2 : final measurement For the relevant emissions determined in step 1, an additional measurement with the following settings will be performed. Intention of this step is to find the maximum emission level.  Open area test side  Antenna distance: according to the Standard  Detector: Quasi-Peak  Frequency range: 0.009 – 30 MHz  Frequency steps: measurement at frequencies detected in step 1  IF–Bandwidth: 0.2 - 10 kHz  Measuring time / Frequency step: 1 s 2 . M e a su r e m e n t a bove 3 0 M H z a n d u p t o 1 GH z St e p 1 : Preliminary scan This is a preliminary test to identify the highest amplitudes relative to the limit. Settings for step 1: - Antenna distance: 3 m - Detector: Peak-Maxhold / Quasipeak (FFT-based) - Frequency range: 30 – 1000 MHz - Frequency steps: 30 kHz Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 12 of 30

- IF–Bandwidth: 120 kHz - Measuring time / Frequency step: 100 ms - Turntable angle range: –180° to 90° - Turntable step size: 90° - Height variation range: 1 – 3 m - Height variation step size: 2 m - Polarisation: Horizontal + Vertical Intention of this step is, to determine the radiated EMI-profile of the EUT. Afterwards the relevant emissions for the final measurement are identified. St e p 2 : Adjustment measurement In this step the accuracy of the turntable azimuth and antenna height will be improved. This is necessary to find out the maximum value of every frequency. For each frequency, which was determined the turntable azimuth and antenna height will be adjusted. The turntable azimuth will slowly vary by ± 45° around this value. During this action, the value of emission is continuously measured. The turntable azimuth at the highest emission will be recorded and adjusted. In this position, the antenna height will also slowly vary by ± 100 cm around the antenna height determined. During this action, the value of emission is also continuously measured. The antenna height of the highest emission will also be recorded and adjusted. - Detector: Peak – Maxhold - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 100 ms - Turntable angle range: ± 45 ° around the determined value - Height variation range: ± 100 cm around the determined value - Antenna Polarisation: max. value determined in step 1 St e p 3 : Final measurement with QP detector With the settings determined in step 3, the final measurement will be performed: EMI receiver settings for step 4: - Detector: Quasi-Peak (< 1 GHz) - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 1 s After the measurement a plot will be generated this contains a diagram with the results of the preliminary scan and a chart with the frequencies and values of the results of the final measurement. 3 . M e a sur e m e nt a bove 1 GH z The following modifications apply to the measurement procedure for the frequency range above 1 GHz: St e p 1 : The Equipment Under Test (EUT) was set up on a non-conductive support (tilt device) at 1.5 m height in the fully-anechoic chamber. All steps were performed with one height of the receiving antenna only. The EUT is turned during the preliminary measurement across the elevation axis, with a step size of 90 °. The turn table step size (azimuth angle) for the preliminary measurement is 45 °. St e p 2 : Due to the fact, that in this frequency range the test is performed in a fully anechoic room, the height scan of the receiving antenna instep 2 is omitted. Instead of this, a maximum search with a step size ± 45° for the elevation axis is performed. The turn table azimuth will slowly vary by ± 22.5°. The elevation angle will slowly vary by ± 45° Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 13 of 30

EMI receiver settings (for all steps): - Detector: Peak, Average - IF Bandwidth = 1 MHz St e p 3 : Spectrum analyser settings for step 3: - Detector: Peak / Average - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 1 MHz - Measuring time: 1 s 3 .2 .2 Te st Re qu ir e m e n t s / Lim it s FCC Part 15, Subpart C, §15.247 (d) ... In addition, radiated emissions which fall in the restricted bands, as defined in Section 15.205(a), must also comply with the radiated emission limits specified in Section 15.209(a) (see Section 15.205(c)). FCC Part 15, Subpart C, §15.209, Radiated Emission Limits Measurement Frequency in MHz Limit (µV/m) Limits (dBµV/m) distance (m) 0.009 – 0.49 2400/F(kHz)@300m 3 (48.5 – 13.8)@300m 0.49 – 1.705 24000/F(kHz)@30m 3 (33.8 – 23.0)@30m 1.705 – 30 30@30m 3 29.5@30m The measured values are corrected with an inverse linear distance extrapolation factor (40 dB/decade) according FCC 15.31 (2). Measurement Frequency in MHz Limit (µV/m) Limits (dBµV/m) distance (m) 30 – 88 100@3m 3 40.0@3m 88 – 216 150@3m 3 43.5@3m 216 – 960 200@3m 3 46.0@3m 960 - 26000 500@3m 3 54.0@3m 26000 - 40000 500@3m 1 54.0@3m The measured values above 26 GHz are corrected with an inverse linear distance extrapolation factor (20 dB/decade). §15.35(b) ..., there is also a limit on the radio frequency emissions, as measured using instrumentation with a peak detector function, corresponding to 20 dB above the maximum permitted average limit.... Used conversion factor: Limit (dBµV/m) = 20 log (Limit (µV/m)/1µV/m) Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 14 of 30

3 .2 .3 Te st Pr ot ocol Temperature: 23 °C Air Pressure: 1009 hPa Humidity: 38 % 3 .2 .3 .1 M e a sur e m e nt up t o 3 0 M H z Op. M ode Se t up Por t op-mode 1 Setup_01 Enclosure Pola r i- Fr e que n cy Cor r e ct e d va lue Lim it Lim it Lim it D e lt a t o D e lt a t o sa t ion MHz dBµ V/ m dBµ V/ dBµ V/ dBµ V/ lim it lim it m m m dB dB QP Pe a k AV QP Pe a k AV QP/ Pe a k AV 0° – – – – – – – – – 90° – – – – – – – – – Remark: No spurious emissions in the range 20 dB below the limit found therefore step 2 was not performed. Please refer to the plot in the annex. 3 .2 .3 .2 M e a sur e m e n t a bove 3 0 M H z Op. M ode Se t up Por t op-mode 1 Setup_01 Enclosure Pola r i- Fr e que n cy Cor r e ct e d va lue Lim it Lim it Lim it D e lt a t o D e lt a t o sa t ion MHz dBµ V/ m dBµ V/ dBµ V/ dBµ V/ lim it lim it m m m dB dB QP Pe a k AV QP Pe a k AV QP/ Pe a k AV Horizontal 352.56 38.4 – – 46.0 – – 7.62 – Horizontal 352.56 35.8 – – 46.0 – – 10.2 – Remark: No further spurious emissions in the range 20 dB below the limit found. 3 .2 .4 Te st r e su lt : Spu r iou s r a dia t e d e m ission s FCC Pa r t 1 5 , Su bpa r t C Op. M ode Re su lt op-mode 1 passed Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 15 of 30

3 .3 Occu pie d ba n dw idt h St a n da r d FCC Part 15, 10-1-15 Edition Subpart C Th e t e st w a s pe r for m e d a ccor din g t o: FCC §15.31 3 .3 .1 Te st D e scr ipt ion The Equipment Under Test (EUT) was setup in a shielded room to perform the occupied bandwidth measurements. The reference level is the level of the highest amplitude signal observed from the transmitter at either the fundamental frequency or first-order modulation products in all typical modes of operation, including the unmodulated carrier, even if atypical. The results recorded were measured with the modulation which produces the worst-case (widest) occupied bandwidth. 3 .3 .2 Te st Re quir e m e n t s / Lim it s FCC Part 15, Subpart C, §15.215 (c) Intentional radiators operating under the alternative provisions to the general emission limits, as contained in §§ 15.217 through 15.257 and in Subpart E of this part, must be designed to ensure that the 20 dB bandwidth of the emission, or whatever bandwidth may otherwise be specified in the specific rule section under which the equipment operates, is contained within the frequency band designated in the rule section under which the equipment is operated. … 3 .3 .3 Te st Pr ot ocol Temperature: 22 °C Air Pressure: 1013 hPa Humidity: 45 % Op. M ode Se t up Por t op-mode 1 Setup_02 Enclosure 2 0 dB ba n dw idt h 9 9 % ba n dw idt h Re m a r k s kHz kHz 432.960 492.051 The 20 dB bandwidth from 13.34322 MHz to 13.77618 MHz is contained within the designated frequency band 13.110 MHz to 14.010 MHz. Remark: Please see annex for the measurement plot. 3 .3 .4 Te st r e su lt : Occu pie d ba ndw idt h FCC Pa r t 1 5 , Su bpa r t C Op. M ode Re su lt op-mode 1 passed Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 16 of 30

3 .4 Spe ct r u m m a sk St a n da r d FCC Part 15, 10-1-15 Edition Subpart C Th e t e st w a s pe r for m e d a ccor din g t o: FCC §15.225 3 .4 .1 Te st D e scr ipt ion The test set-up was made in accordance to the general provisions of ANSI C 63.10–2013. The Equipment Under Test (EUT) was set up on a non-conductive table in the anechoic chamber. The radiated emissions measurements were made in a typical installation configuration. The measurement procedure is implemented into the EMI test software ES-K1 from R&S. The Loop antenna HFH2-Z2 is used. - Anechoic chamber - Antenna distance: 3 m - Detector: Peak-Maxhold - Frequency range: 13.06 – 14.06 MHz - Frequency steps: 5 kHz - IF–Bandwidth:10 kHz - Measuring time / Frequency step: 100 ms 3 .4 .2 Te st Lim it s FCC Part 15, Subpart C, §15.225 (a-d), and §15.209, corrected by the means of the extrapolation of §15.31 due to the reduced measuring distance from 30 m to 3 m with an inverse linear distance extrapolation factor (40 dB/decade). 3 .4 .3 Te st Pr ot ocol Temperature: 22 °C Air Pressure: 1013 hPa Humidity: 40 % Op. M ode Se t up Por t op-mode 1 Setup_01 Enclosure M a x im u m va lu e Lim it Re m a r k s dBµ V/ m @ 3 0 m dBµ V/ m @ 3 0 m 15.56 84.0 measuring distance 3 m Remark: Please see annex for the measurement plot. 3 .4 .4 Te st r e su lt : Spe ct r u m m a sk FCC Pa r t 1 5 , Su bpa r t C Op. M ode Re su lt op-mode 1 passed Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 17 of 30

3 .5 Fr e qu e n cy t ole r a n ce St a n da r d FCC Part 15, 10-1-15 Edition Subpart C Th e t e st w a s pe r for m e d a ccor din g t o: FCC §15.225 3 .5 .1 Te st D e scr ipt ion The Equipment Under Test (EUT) is placed in a temperature chamber. The frequency drift during temperature and voltage variation is measured by the means of a spectrum analyzer with frequency counter function. The temperature was varied from –40 °C to +85 °C. At +20 °C the extreme power supply voltages of 3.0 V and 3.6 V are applied. After reaching each target temperature and waiting sufficient time allowing the temperature to stabilize, one measurement is performed immediately after powering on the EUT, and three further measurements are performed after 2, 5 and 10 minutes continuous operation of EUT. 3 .5 .2 Te st Lim it s FCC Part 15, Subpart C, §15.225 (e): The frequency tolerance of the carrier signal shall be maintained within ±0.01% of the operating frequency over a temperature variation of -20 degrees to +50 degrees C at normal supply voltage, and for a variation in the primary supply voltage from 85% to 115% of the rated supply voltage at a temperature of 20 degrees C. Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 18 of 30

3 .5 .3 Te st Pr ot ocol Temperature: -40°C to +85°C Air Pressure: 1009 hPa Humidity: 38 % Op. M ode Se t up Por t op-mode 2 Setup_01 Enclosure Te m pe r a t u r e Volt a ge Tim e Fr e qu e n cy D e lt a Ve r dict / °C / V / m in. / MHz / Hz 50 3.30 0 13.559882 -118 Passed 50 3.30 2 13.559880 -120 Passed 50 3.30 5 13.559879 -121 Passed 50 3.30 10 13.559878 -122 Passed 40 3.30 0 13.559924 -76 Passed 40 3.30 2 13.559920 -80 Passed 40 3.30 5 13.559919 -81 Passed 40 3.30 10 13.559918 -82 Passed 30 3.30 0 13.559997 -3 Passed 30 3.30 2 13.559976 -24 Passed 30 3.30 5 13.559974 -26 Passed 30 3.30 10 13.559972 -28 Passed 20 3.60 0 13.560031 31 Passed 20 3.60 2 13.560030 30 Passed 20 3.60 5 13.560029 29 Passed 20 3.60 10 13.560029 29 Passed 20 3.30 0 13.560032 32 Passed 20 3.30 2 13.560031 31 Passed 20 3.30 5 13.560029 29 Passed 20 3.30 10 13.560030 30 Passed 20 3.00 0 13.560031 31 Passed 20 3.00 2 13.560030 30 Passed 20 3.00 5 13.560029 29 Passed 20 3.00 10 13.560030 30 Passed 10 3.30 0 13.560086 86 Passed 10 3.30 2 13.560085 85 Passed 10 3.30 5 13.560084 84 Passed 10 3.30 10 13.560084 84 Passed 0 3.30 0 13.560130 130 Passed 0 3.30 2 13.560127 127 Passed 0 3.30 5 13.560127 127 Passed 0 3.30 10 13.560127 127 Passed -10 3.30 0 13.560153 153 Passed -10 3.30 2 13.560152 152 Passed -10 3.30 5 13.560152 152 Passed -10 3.30 10 13.560152 152 Passed -20 3.30 0 13.560141 141 Passed -20 3.30 2 13.560143 143 Passed -20 3.30 5 13.560144 144 Passed -20 3.30 10 13.560144 144 Passed Continue on the next page Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 19 of 30

Additional measurements to prove the EUT working ability from -40° C to +85° C Temperature Voltage Time Frequency Delta Verdict / °C /V / min. / MHz / Hz 85 3.3 0 13.559920 -80 Passed 85 3.3 2 13.559937 -63 Passed 85 3.3 5 13.559945 -55 Passed 85 3.3 10 13.559945 -55 Passed 80 3.3 0 13.559899 -101 Passed 80 3.3 2 13.559904 -96 Passed 80 3.3 5 13.559906 -94 Passed 80 3.3 10 13.559908 -92 Passed 70 3.3 0 13.559862 -138 Passed 70 3.3 2 13.559863 -137 Passed 70 3.3 5 13.559864 -136 Passed 70 3.3 10 13.559866 -134 Passed 60 3.3 0 13.559859 -141 Passed 60 3.3 2 13.559858 -142 Passed 60 3.3 5 13.559858 -142 Passed 60 3.3 10 13.559858 -142 Passed -30 3.3 0 13.560103 103 Passed -30 3.3 2 13.560106 106 Passed -30 3.3 5 13.560106 106 Passed -30 3.3 10 13.560106 106 Passed -40 3.3 0 13.560029 29 Passed -40 3.3 2 13.560033 33 Passed -40 3.3 5 13.560030 30 Passed -40 3.3 10 13.560031 31 Passed Remark: The limit is a delta of max. ±1356 Hz (0.01 %). 3 .5 .4 Te st r e su lt : Fr e qu e n cy t ole r a n ce FCC Pa r t 1 5 , Su bpa r t C Op. M ode Re su lt op-mode 2 passed Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 20 of 30

4 Te st Equ ipm e n t 1 Ra dia t e d Em ission s Lab to perform radiated emission tests Re f.N o. D e vice N a m e D e scr ipt ion M a n u fa ct u r e r Se r ia l N u m be r Ca libr a t ion Due 1.1 Fully Anechoic 8.80m x 4.60m x Albatross Projects P26971-647-001-PRB Room 4.05m (l x w x h) 1.2 AM 4.0 Antenna mast Maturo GmbH AM4.0/180/11920513 1.3 ESR 7 EMI Receiver / Rohde & Schwarz 101424 2016-11-13 Spectrum Analyzer 1.4 Anechoic Chamber 10.58 x 6.38 x Frankonia none 2017-01-09 6.00 m³ 1.5 ESIB 26 Spectrum Analyzer Rohde & Schwarz 830482/004 2017-12-08 1.6 Tilt device Maturo Antrieb TD1.5- Maturo GmbH TD1.5- (Rohacell) 10kg 10kg/024/3790709 1.7 AS 620 P Antenna mast HD GmbH 620/37 1.8 NRV-Z1 Sensor Head A Rohde & Schwarz 827753/005 2016-05-11 1.9 JS4-18002600-32- Broadband Miteq 849785 5P Amplifier 18 GHz - 26 GHz 1.10 HL 562 Ultralog new Rohde & Schwarz 830547/003 2018-06-30 biconicals GmbH & Co. KG 1.11 Opus10 THI ThermoHygro Lufft Mess- und 12482 2017-03-10 (8152.00) Datalogger 12 Regeltechnik (Environ) GmbH 1.12 HFH2-Z2 Loop Antenna Rohde & Schwarz 829324/006 2017-11-27 GmbH & Co. KG 1.13 FSW 43 Spectrum Analyzer Rohde & Schwarz 103779 2016-11-17 1.14 Opus10 TPR ThermoAirpressure Lufft Mess- und 13936 2017-02-27 (8253.00) Datalogger 13 Regeltechnik (Environ) GmbH 1.15 Chroma 6404 AC Power Source Chroma ATE INC. 64040001304 1.16 3160-10 Standard Gain / EMCO Elektronik 00086675 Pyramidal Horn GmbH Antenna 40 GHz 1.17 HL 562 Ultralog Log.-per. Antenna Rohde & Schwarz 100609 2016-03-18 GmbH & Co. KG 1.18 HF 907 Double-ridged Rohde & Schwarz 102444 2018-05-11 horn GmbH & Co. KG 1.19 DE 325 Dreheinheit HD GmbH Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 21 of 30

2 Ra dio La b Conducted Radio Test Lab Re f.N o. D e vice N a m e D e scr ipt ion M a n u fa ct u r e r Se r ia l N u m be r Ca libr a t ion Due 2.1 A8455-4 4 Way Power - Divider (SMA) 2.2 SMB100A Signal Generator Rohde & Schwarz 107695 2017-06-06 9 kHz - 6 GHz GmbH & Co. KG 2.3 VT 4002 Climatic Chamber Vötsch 58566002150010 2016-03-11 2.4 SMP03 Signal Generator Rohde & Schwarz 833680/003 2016-10-29 2 GHz - 27 GHz GmbH & Co. KG 1035.5005.03 2.5 FSV30 Signal Analyzer Rohde & Schwarz 103005 2018-02-10 10 Hz - 30 GHz 2.6 SMBV100A Vector Signal Rohde & Schwarz 259291 2016-08-23 Generator 9 kHz - GmbH & Co. KG 6 GHz 2.7 Voltcraft M-3860M Digital Multimeter Voltcraft IJ096055 01 (Multimeter) 2.8 Chroma 6404 AC Power Source Chroma ATE INC. 64040001304 2.9 Datum, Model: MFS Rubidium Datum-Beverly 5489/001 2016-06-25 Frequency Standard 2.10 WA1515 Broadband Power Weinschel A855 Divider SMA Associates 2.11 FSIQ26 Spectrum Rohde & Schwarz 840061/005 2017-04-02 Analyzer 7layers, GmbH & Co. KG Ratingen OIL_RE 3 R& S TS8 9 9 7 EN300328/301893 Test Lab Re f.N o. D e vice N a m e D e scr ipt ion M a n u fa ct u r e r Se r ia l N u m be r Ca libr a t ion Due 3.1 OSP120 Switching Unit Rohde & Schwarz 101158 2016-08-21 with integrated GmbH & Co. KG power meter 3.2 A8455-4 4 Way Power - Divider (SMA) 3.3 Opus10 THI ThermoHygro Lufft Mess- und 7482 2017-02-27 (8152.00) Datalogger 03 Regeltechnik (Environ) GmbH 3.4 SMB100A Signal Generator Rohde & Schwarz 107695 2017-06-06 9 kHz - 6 GHz GmbH & Co. KG 3.5 VT 4002 Climatic Chamber Vötsch 58566002150010 2016-03-11 3.6 FSV30 Signal Analyzer Rohde & Schwarz 103005 2018-02-10 10 Hz - 30 GHz 3.7 SMBV100A Vector Signal Rohde & Schwarz 259291 2016-08-23 Generator 9 kHz - GmbH & Co. KG 6 GHz 3.8 Voltcraft M-3860M Digital Multimeter Voltcraft IJ096055 01 (Multimeter) 3.9 1515 / 93459 Broadband Power Weinschel LN673 Divider SMA Associates (Aux) 3.10 Datum, Model: MFS Rubidium Datum-Beverly 5489/001 2016-06-25 Frequency Standard Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 22 of 30

5 Ph ot o Re por t Photos are included in an external report. 6 Se t u p D r a w in gs D r a w in g 1 : Setup in the Anechoic chamber: Measurements below 1 GHz: Semi-anechoic, conducting ground plane. Measurements above 1 GHz: Fully-anechoic, absorbers on all surfaces. Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 23 of 30

7 FCC a nd I C Cor r e la t ion of m e a su r e m e n t r e qu ir e m e n t s The following tables show the correlation of measurement requirements Radio equipment operating in the Band 13.110-14.010 MHz from FCC and IC. Ra dio e qu ipm e n t M e a sur e m e n t FCC r e fe r e n ce I C r e fe r e nce Conducted emissions on AC § 15.207 RSS-Gen Issue 4: 8.8 Mains Additional provisions to the § 15.215 RSS-Gen Issue 4: 6.6 general radiated emission limitations Out-of-band emissions § 15.225 (d) RSS Gen Issue 4: 6.13/8.9/8.10; RSS-210 Issue 8: A2.6 In-band emissions § 15.225 (a) / (b) / (c) RSS-210 Issue 8: A2.6 Frequency Stability § 15.225 (e) RSS-210 Issue 8: A2.6 Antenna requirement § 15.203 / 15.204 RSS-Gen Issue 4: 8.3 Receiver spurious emissions – RSS-210 Issue 8: 2.3; RSS Gen Issue 4: 5/7 *) Handling of active and § 15.225 (f) RSS Gen Issue 4: 8.7 passive tag devices of RFID application *) Receivers are exempted from certification besides if operating in stand-alone mode in the frequency range 30–960 MHz or if these are scanner receivers. Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 24 of 30

8 An n e x m e a su r e m e n t plot s 8 .1 Ra dia t e d e m ission s 8 .1 .1 Ra dia t e d e m ission s ( f < 3 0 M H z) 70 60 13.560000 MHz 14.665 dBµV/m 40 FCC_15.209_Peak@300m_9kHz-490kHz FCC_15.209_QP@300m@30m_90kHz-30MHz 20 FCC_15.209_AV@300m_9kHz-490kHz 27.120000 MHz Level in dBµV/m -0.848 dBµV/m 0 -20 -40 -60 9k 20 30 50 100k 200 300 500 1M 2M 3M 5M 10M 20 30M Frequency in Hz Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 25 of 30

8 .1 .2 Ra dia t e d e m ission s ( f > 3 0 M H z) EUT in a vertical position 60 FCC_15.209_30M-1GHz@3m 50 40 Level in dBµV/m 30 20 10 0 30M 50 60 80 100M 200 300 400 500 800 1G Frequency in Hz EUT in a horizontal position 60 FCC_15.209_30M-1GHz@3m 50 40 Level in dBµV/m 30 20 10 0 30M 50 60 80 100M 200 300 400 500 800 1G Frequency in Hz Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 26 of 30

8 .2 AC M a in s con du ct e d Measurement performed with a real antenna. 80 70 Limit_15_207_QP 60 Limit_15_207_AV 50 Level in dBµV 40 30 20 10 0 150k 300 400 500 800 1M 2M 3M 4M 5M 6 8 10M 20M 30M Frequency in Hz Measurement performed with a real antenna (zoomed). 70.2 Limit_15_207_QP 60 Limit_15_207_AV 50 Level in dBµV 40 30 20 10 0.7 8.823 10 11 12 13 14 15 16 17 18 18.608 Frequency in MHz Note: Measured levels above the limit are from modulated carrier signal. Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 27 of 30

Measurement performed with a 50 Ω dummy antenna 80 70 Limit_15_207_QP 60 Limit_15_207_AV Level in dBµV 50 40 30 20 10 0 150k 300 400 500 800 1M 2M 3M 4M 5M 6 8 10M 20M 30M Frequency in Hz Fina l Re sult Frequency QuasiPeak Average Limit Margin Meas. Time Bandwidth Line PE Corr. Comment (MHz) (dBµV) (dBµV) (dBµV) (dB) (ms) (kHz) (dB) 0.217500 --- 23.31 52.91 29.61 1000.0 9.000 L1 GND 10.1 16:54:48 - 06/01/2016 0.339000 23.36 --- 59.23 35.87 1000.0 9.000 N GND 10.1 16:54:13 - 06/01/2016 13.348500 --- 24.65 50.00 25.35 1000.0 9.000 L1 GND 10.7 16:54:53 - 06/01/2016 13.454250 --- 22.30 50.00 27.70 1000.0 9.000 L1 GND 10.7 16:54:58 - 06/01/2016 13.454250 27.39 --- 60.00 32.61 1000.0 9.000 N GND 10.7 16:54:19 - 06/01/2016 13.560000 --- 41.43 50.00 8.57 1000.0 9.000 L1 GND 10.7 16:55:02 - 06/01/2016 13.560000 41.57 --- 60.00 18.43 1000.0 9.000 N GND 10.7 16:54:24 - 06/01/2016 13.665750 27.40 --- 60.00 32.60 1000.0 9.000 N GND 10.7 16:54:30 - 06/01/2016 13.665750 --- 22.26 50.00 27.74 1000.0 9.000 L1 GND 10.7 16:55:07 - 06/01/2016 13.771500 --- 24.43 50.00 25.57 1000.0 9.000 L1 GND 10.7 16:55:11 - 06/01/2016 23.583750 --- 27.86 50.00 22.14 1000.0 9.000 N GND 11.1 16:55:16 - 06/01/2016 26.907000 --- 29.66 50.00 20.34 1000.0 9.000 L1 FLO 11.2 16:54:35 - 06/01/2016 27.120750 46.86 --- 60.00 13.14 1000.0 9.000 L1 FLO 11.2 16:54:07 - 06/01/2016 27.120750 --- 46.55 50.00 3.45 1000.0 9.000 L1 FLO 11.2 16:54:39 - 06/01/2016 27.332250 --- 29.58 50.00 20.42 1000.0 9.000 N FLO 11.2 16:54:44 - 06/01/2016 Hardware Setup: EMI_Conducted_EN_FCC_ESH3-Z5 Measurement Type: 2 Line LISN Frequency Range: 150 kHz - 30 MHz Graphics Level Range: 0 dBµV - 80 dBµV Preview Measurements: Scan Test Template: FCC_Part207_Pre_ESH3-Z5 Final Measurements: Template for Single Meas.: FCC_Part207_Final_ESH3-Z5 Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 28 of 30

8 .3 Occu pie d ba n dw idt h Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 29 of 30

8 .4 Spe ct r u m m a sk 90 80 70 60 50 Level in dBµV/m 40 FCC_15.225_TX-Mask@30m_13-56MHz 30 20 10 0 -10 13 13.1 13.2 13.3 13.4 13.5 13.6 13.7 13.8 13.9 14 14.1 Frequency in MHz Final_Result Frequency MaxPeak QuasiPeak Limit Margin Meas. Bandwidth Height Pol Azimuth Corr. Comment (MHz) (dBµV/m) (dBµV/m) (dBµV (dB) Time (kHz) (cm) (deg) (dB) /m) (ms) 13.560000 --- 13.76 84.00 70.24 1000.0 10.000 100.0 H 53.0 -19.9 10:39:14 - 05/01/2016 13.560000 15.56 --- 84.00 68.44 1000.0 10.000 100.0 H 53.0 -19.9 10:39:14 - 05/01/2016 Test report Reference: MDE_UBLOX_1551_FCCe_Rev.1 Page 30 of 30


Document Created: 2017-12-13 05:36:35
Document Modified: 2017-12-13 05:36:35
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC