RF Exposure Report I

FCC ID: XPY2AGQN4NNN

RF Exposure Info

Download: PDF
FCCID_4391944

RF Exposure and Maximum ERP/EIRP Assessment For SARA-R410 Cat M1 FCC ID: XPY2AGQN4NNN IC: 8595A-2AGQN4NNN Assessment Reference: MDE_UBLOX_1901_MPE_CatM1 Test Laboratory: 7layers GmbH Borsigstraße 11 40880 Ratingen Germany Note: The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts without the written approval of the test laboratory. 7layers GmbH Registergericht registered in: Borsigstraße 11 Geschäftsführer / Düsseldorf, HRB 75554 40880 Ratingen, Germany Managing Directors: USt-IdNr VAT No.: T +49 (0) 2102 749 0 Frank Spiller DE203159652 F +49 (0) 2102 749 350 Bernhard Retka TAX No. 147/5869/0385 www.7layers.com Alexandre Norré-Oudard A Bureau Veritas Group Company

Table of Contents 0 Summary 3 0.1 Technical Report Summary 3 1 Administrative Data 4 1.1 Testing Laboratory 4 1.2 Project Data 4 1.3 Applicant Data 4 1.4 Manufacturer Data 4 2 Test object Data 5 2.1 General EUT Description 5 2.2 EUT Main components 5 2.3 Ancillary Equipment 5 2.4 Auxiliary Equipment 5 3 Evaluation Results 6 3.1 Maximum ERP / EIRP 6 3.2 RF Exposure Evaluation for Module 7 Assessment Reference: MDE_UBLOX_1901_MPE_CatM1 Page 2 of 8

%layers A Bureau Veritas Group Company 0 Summary 0. 1. Technical Report Summary Type of Report RF Exposure and Maximum ERP/EIRP Assessment for a GSM/UMTS radio module. Including RF Exposure for use with co—located radios on generic host device. Applicable FCC and ISED Rules For RF Exposure: OET Bulletin 65 Edition 97—01 August 1997 FCC 47 CFR §1.1307 FCC 47 CFR §1.1310 RSS—102 Issue 5 — March 2015 For Maximum ERP/EIRP: IC SRSP—503 Issue 7, September 2008 IC SRSP—510 Issue 5, February 2009 IC RSS—132, Issue 3, FCC 47 CFR §22.913 IC RSS—133 Issue 6, FCC 47 CFR §24.232 IC RSS—139, Issue 3 / SRSP—513, FCC 47 CFR §27.50(d) IC RSS—140, Issue 1, FCC 47 CFR §90.635 Report version control Rev Version Release date Changes Version validity 2019—06—03 Initial version Valid Responsible for Responsible Accreditation Scope: . _ for Report: _ Assessment Reference: MDE_UBLOX_1901_MPE_CatM1 Page 3 of 8

1 Administrative Data 1.1 Testing Laboratory Company Name: 7layers GmbH Address Borsigstr. 11 40880 Ratingen Germany DAkkS ISO/IEC 17025 accreditation D-PL-12140-01-00, D-PL-12140-01-01 FCC accreditation Designation Number: DE0015 Test Firm Registration #: 929146 ISED accreditation CAB identifier: DE0007 Test Firm Registration #: 3699A Responsible for Accreditation Scope: Dipl.-Ing. Bernhard Retka Dipl.-Ing. Robert Machulec Dipl.-Ing. Andreas Petz Dipl.-Ing. Marco Kullik Report Template Version: 2017-08-02 1.2 Project Data Responsible for assessment and report: Mr. Roseelan Sathiyaseelan Date of Report: 2019-06-03 1.3 Applicant Data Company Name: u-blox, Inc Address: 12626 High Bluff Dr, Ste 200 San Diego, CA92130 US Contact Person: Jake Bascon 1.4 Manufacturer Data Company Name: please see applicant data Address: Contact Person: Assessment Reference: MDE_UBLOX_1901_MPE_CatM1 Page 4 of 8

2 Test object Data 2.1 General EUT Description Equipment under Test SARA-R410 Module Type Designation: SARA-R410 Kind of Device: Cat M1/ NB-IOT Module GSM MSC/UMTS/LTE LTE (CAT-M1), NB-IoT FCC ID: XPY2AGQN4NNN IC Number: 8595A-2AGQN4NNN General product description: The EUT is Cellular radio module supporting LTE Category M1 and NB-IoT. 2.2 EUT Main components Type, S/N, Short Descriptions etc. used in this Test Report Short Description Equipment Type Serial No. HW Status SW Status under Test Designation EUT A Code: DE1015105 SARA-R410 SARA-R410352753095787196 306B01 L0.08.01 AB01 Remark: EUT A is equipped with a temporary antenna connector. The Module is not sold with a predefined antenna. NOTE: The short description is used to simplify the identification of the EUT in this test report. 2.3 Ancillary Equipment For the purposes of this test report, ancillary equipment is defined as equipment which is used in conjunction with the EUT to provide operational and control features to the EUT. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless, Ancillary Equipment can influence the test results. Short Equipment Type HW Status SW Status Serial no. FCC ID Description under Test Designation NA – 2.4 Auxiliary Equipment For the purposes of this test report, auxiliary equipment is defined as equipment which is used temporarily to enable operational and control features especially used for the tests of the EUT which is not used during normal operation or equipment that is used during the tests in combination with the EUT but is not subject of this test report. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless, Auxiliary Equipment can influence the test results. Short Equipment Type Serial no. HW Status SW Status FCC ID Description under Test Designation N/A – Assessment Reference: MDE_UBLOX_1901_MPE_CatM1 Page 5 of 8

3 Evaluation Results 3.1 Maximum ERP / EIRP Standard Frequency Band FCC 47 CFR §22.913 eFDD5, eFDD26 IC RSS-132, Issue 3 FCC 47 CFR §24.232 eFDD2, eFDD25 IC RSS-133 Issue 6 FCC 47 CFR §27.50(d) eFDD4, eFDD12, eFDD13 IC RSS-139, Issue 3 / SRSP-513 FCC 47 CFR §90.635 eFDD26 IC RSS-140, Issue 1 3.1.1 Test Limits For the 850MHz band, FCC §22.913 states that the maximum ERP of this device shall not exceed 7 Watts. IC SRSP-503 Issue 7, states that this device shall not exceed a maximum EIRP of 11.5 Watts. For the purposes of this test report, the 7 Watt ERP limit stipulated in FCC §22.913 has been converted to an equivalent ERIP value of 11.5 Watts. For all other limits, refer to the values stipulated in the corresponding tables. 3.1.2 Test Protocol Maximum antenna gain to comply with EIRP limits for FCC and Industry Canada Maximum Maximum Maximum Conducted Conducted antenna output output Freq of gain to Duty Cycle Frequency power power highest FCC EIRP meet EIRP Band Mode (%) (MHZ) (dBm) (mW) power limit (mW) Limit (dBi) eFDD2 LTE 100.0% 1850-1910 22.74 187.93168 1850.00 2000 10.3 eFDD4 LTE 100.0% 1710-1755 22.41 174.18069 1755.00 1000 7.6 eFDD5 LTE 100.0% 824 - 849 23.24 210.86281 836.50 11484 17.4 eFDD13 LTE 100.0% 777-787 23.75 237.13737 787.00 4920 13.2 eFDD12 LTE 100.0% 698-716 22.74 187.93168 707.50 4921 14.2 eFDD25 LTE 100.0% 1850-1915 22.49 177.41895 1882.50 4923 14.4 eFDD26 LTE 100.0% 814-849 22.97 198.1527 849.00 4924 14.0 3.1.3 Conclusion Max gain Max gain Max gain Maximum to be used to be used to be used gain to be Band to comply to comply to comply compliant with EIRP with FCC with IC with all Limits MPE Limits MPE Limits limits eFDD2 10.3 12.0 8.5 8.5 eFDD4 7.6 12.0 8.4 7.6 eFDD5 17.4 9.5 6.2 6.2 eFDD13 13.2 9.2 6.0 6.0 eFDD12 14.2 9.2 6.1 6.1 eFDD25 14.4 14.2 9.8 9.8 eFDD26 14.0 11.1 7.8 7.8 Assessment Reference: MDE_UBLOX_1901_MPE_CatM1 Page 6 of 8

3.2 RF Exposure Evaluation for Module Standards OET Bulletin 65 Edition 97-01 August 1997 RSS-102 Issue 5 – March 2015 3.2.1 Test limits Limits specified per RSS-102, Issue 5. Frequency range (MHz) Power density (W/m²) Power density (mW/cm²) 300 – 6000 0.02619 f0.6834 mW/cm² = W/m² * 0.1 Equation OET bulletin 65, page 18, edition 97-01: 𝑆= = ² Where: S = power density P = power input to the antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the centre of radiation of the antenna 3.2.2 Test Protocol Maximum antenna gain to comply with MPE limits for Industry Canada Maximum Maximum Equivalent Maximum Conducted Conducted conducted antenna output output output gain to Separation Frequency power power power MPE Limit meet MPE distance Band Mode Duty Cycle (MHZ) (dBm) (mW) (mW) (mW/cm²) Limit (dBi) (cm) eFDD2 LTE 100% 1850.0 25.0 316.23 316.23 0.4476 8.5 20 eFDD4 LTE 100% 1755.0 25.0 316.23 316.23 0.4318 8.4 20 eFDD5 LTE 100% 836.5 25.0 316.23 316.23 0.2602 6.2 20 eFDD13 LTE 100% 787.0 25.0 316.23 316.23 0.2496 6.0 20 eFDD12 LTE 100% 707.5 25.0 316.23 316.23 0.2321 6.1 20 eFDD25 LTE 100% 1882.5 25.0 316.23 316.23 0.4530 9.8 20 eFDD26 LTE 100% 849.0 25.0 316.23 316.23 0.2629 7.8 20 Assessment Reference: MDE_UBLOX_1901_MPE_CatM1 Page 7 of 8

Maximum antenna gain to comply with MPE limits for FCC Maximum Maximum Equivalent Maximum Conducted Conducted conducted antenna output output output gain to Separation Frequency power power power MPE Limit meet MPE distance Band Mode Duty Cycle (MHZ) (dBm) (mW) (mW) (mW/cm²) Limit (dBi) (cm) eFDD2 LTE 100.0% 1850.0 25 316.23 316.23 1.0000 12.0 20 eFDD4 LTE 100.0% 1755.0 25 316.23 316.23 1.0000 12.0 20 eFDD5 LTE 100.0% 836.5 25 316.23 316.23 0.5577 9.5 20 eFDD13 LTE 100.0% 777.0 25 316.23 316.23 0.5247 9.2 20 eFDD12 LTE 100.0% 707.5 25 316.23 316.23 0.4717 9.2 20 eFDD25 LTE 100.0% 1882.5 25 316.23 316.23 1.2550 14.2 20 eFDD26 LTE 100.0% 849.0 25 316.23 316.23 0.5660 11.1 20 3.2.3 Conclusion Max gain Maximum Max gain for gain to be Band for FCC Industry compliant MPE Limits Canada with all MPE Limits limits eFDD2 12.0 8.5 8.5 eFDD4 12.0 8.4 8.4 eFDD5 9.5 6.2 6.2 eFDD13 9.2 6.0 6.0 eFDD12 9.2 6.1 6.1 eFDD25 14.2 9.8 9.8 eFDD26 11.1 7.8 7.8 Gain expressed in dBi Assessment Reference: MDE_UBLOX_1901_MPE_CatM1 Page 8 of 8


Document Created: 2019-06-04 14:48:24
Document Modified: 2019-06-04 14:48:24
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC