Test Report

FCC ID: XPY1EIQN2NN

Test Report

Download: PDF
FCCID_3165127

FCC Measurement/Technical Report on LARA—R204 According to: FCC Part 15, Subpart B FCC ID: XPY1 EIQN2Z2NN 1IC: 8595A¥—1EIQN2NN Test Report Reference: MDE_UBLOX_1603_FCCb Test Laboratory: 7layers GmbH Borsigstrasse 11 ((( DAkkS 40880 Ratingen Deutsche Abkreditierungsstelle Germany b—Pi—t2140.01—01 Note The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts without the written approval of the test laboratory: Tlayers GmbH Goschifteithro Borsigstratle 11 Managing Diractors Regist argaricht/ragistered a Bureau Vertas 40880 Ratingen, Garm any Frank Spiler Dlissaldort HRB 75584 Group Company T+49 (0) 2102 7« 0 Bormhard Retka US—Id.—Nr/VAT—No. De203159032 F»48 (0) 2102 749 aso Alexandire Norré—Oudard Steuer—Nr./TAX—No. 1477580970305 wan.Zlayers.com Commerzbank AG Account No. 303018000 Bank Code 30040000 IBAN DE81800400000308016000 Swit Code COBADEFF

Table of Contents 1 Applied Standards and Test Summary 3 1.1 Applied Standards 3 1.2 FCC-IC Correlation Table 4 1.3 Measurement Summary / Signatures 5 2 Administrative Data 6 2.1 Testing Laboratory 6 2.2 Project Data 6 2.3 Applicant Data 6 2.4 Manufacturer Data 6 3 Test object Data 7 3.1 General EUT Description 7 3.2 EUT Main components 7 3.3 Ancillary Equipment 7 3.4 Auxiliary Equipment 8 3.5 EUT Setups 8 3.6 Operating Modes 9 3.7 Product labelling 9 4 Test Results 10 4.1 Conducted Emissions at AC mains 10 4.2 Radiated Emissions 13 5 Test Equipment 17 6 Antenna Factors, Cable Loss and Sample Calculations 20 6.1 LISN R&S ESH3-Z5 (150 kHz – 30 MHz) 20 6.2 Antenna R&S HFH2-Z2 (9 kHz – 30 MHz) 21 6.3 Antenna R&S HL562 (30 MHz – 1 GHz) 22 6.4 Antenna R&S HF907 (1 GHz – 18 GHz) 23 6.5 Antenna EMCO 3160-09 (18 GHz – 26.5 GHz) 24 6.6 Antenna EMCO 3160-10 (18 GHz – 26.5 GHz) 25 7 Setup Drawings 26 8 Measurement Uncertainties 27 9 Photo Report 27 TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 2 of 27

1 APPLIED STANDARDS AND TEST SUMMARY 1.1 APPLIED STANDARDS Applicable FCC Rules Prepared in accordance with the requirements of FCC Rules and Regulations as listed in 47 CFR Ch.1 Parts 2 and 15 (10-1-15 Edition). The following subparts are applicable to the results in this test report. Part 2, Subpart J - Equipment Authorization Procedures, Certification Part 15, Subpart B – Unintentional Radiators § 15.107 Conducted limits § 15.109 Radiated emission limits; general requirements Note: ANSI C63.4–2014 is applied. TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 3 of 27

Summary Test Results: The EUT complied with all performed tests as listed in chapter 1.3 Measurement Summary / Signatures. 1.2 FCC-IC CORRELATION TABLE Correlation of measurement requirements for Information Technology Equipment (ITE) from FCC and IC Measurement FCC reference IC reference Conducted Emissions §15.107 ICES-003 Issue 6: 6.1 (AC Power Line) Radiated Spurious Emissions §15.109 ICES-003 Issue 6: 6.2 Remarks: 1. FCC Part 15 subpart B, ICES 003 and CISPR 22 contain different definitions of Class A and Class B limits, i.e. which class is applicable to which kind of EUT. ICES 003 and CISPR 22 distinguish between the location where the EUT is intended to operate whilst FCC refers to the method of commercial distribution (distributive trades). 2. The correct assignment of the appropriate class to the concrete EUT is not scope of this test report! 3. A radio apparatus that is specifically subject to an Industry Canada Radio Standard Specification (RSS) and which contains an ITE is not subject to ICES-003 provided the ITE is used only to enable operation of the radio apparatus and the ITE does not control additional functions or capabilities. 4. ISM (Industrial, Scientific or Medical) radio frequency generators, though they may contain ITE, are excluded from the definition of ITE and are not subject to ICES-003. They are instead subject to the Interference-Causing Equipment Standard ICES-001, which specifically addresses ISM radio frequency generators. TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 4 of 27

%layers A Bureau Veritas Group Company 1.3 MEASUREMENT SUMMARY / SIGNATURES 47 CFR CHAPTER I FCC PART 15 Subpart B § 15.107 Conducted Emissions at AC mains The measurement was performed according to ANSI C63.4 Final Result OP—Mode Setup FCC IC AC mains connection, Test setup via connected computer device, computer peripheric S01_AYO2 Passed Passed 47 CFR CHAPTER I FCC PART 15 Subpart B § 15.109 Radiated Emissions The measurement was performed according to ANSI C63.4 Final Result OP—Mode Setup FCC IC AC mains connection, Measurementrange, Test setup via connected computer device, 1 GHz — 10 GHz, computer S01_AYO2 Passed Passed peripheric via connected computer device, 30 MHz — 1 GHz, computer S01_AYO2 Passed Passed peripheric @i (responsible for accreditation Q/L_(responsible for testing and report) scope) Dipl. Bernhard Retka Patrick Lomax TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 5 of 27

2 ADMINISTRATIVE DATA 2.1 TESTING LABORATORY Company Name: 7layers GmbH Address: Borsigstr. 11 40880 Ratingen Germany This facility has been fully described in a report submitted to the FCC and accepted under the registration number 96716. This facility has been fully described in a report submitted to the IC and accepted under the registration number: Site# 3699A-1. The test facility is also accredited by the following accreditation organisation: Laboratory accreditation no: DAkkS D-PL-12140-01-01 Responsible for accreditation scope: Dipl. Marco Kullik Report Template Version: 2016-06-07 2.2 PROJECT DATA Responsible for testing and report: Patrick Lomax Employees who performed the tests: documented internally at 7Layers Date of Report: 2016-09-24 Testing Period: 2016-09-10 to 2016-09-22 2.3 APPLICANT DATA Company Name: u-blox AG Address: Zürcherstrasse 68 CH-8800 Thalwil Switzerland Contact Person: Giulio Comar 2.4 MANUFACTURER DATA Company Name: See applicant data Address: Contact Person: TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 6 of 27

3 TEST OBJECT DATA 3.1 GENERAL EUT DESCRIPTION Kind of Device LTE Data module product description Product name LARA-R204 Type LARA-R204 Declared EUT data by the supplier Power Supply Type DC Comment DC Power via AC/DC adapter Test Voltage / 120v/60Hz AC Frequency Highest internal Above 108 MHz frequency General Description UMTS/LTE Voice and Data module Ports USB, RF The main components of the EUT are listed and described in chapter 3.2 EUT Main components. 3.2 EUT MAIN COMPONENTS Sample Name Sample Code Description Standard Sample AY02 Standard sample Sample Parameter Value HW Version 266A00 Serial No. 357648070021592 SW Version 31.02 NOTE:The short description is used to simplify the identification of the EUT in this test report. 3.3 ANCILLARY EQUIPMENT For the purposes of this test report, ancillary equipment is defined as equipment which is used in conjunction with the EUT to provide operational and control features to the EUT. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Ancillary Equipment can influence the test results. Device Details Description (Manufacturer, Type Model, OUT Code) AC/DC converter UNIFIVE, UUX324-1215, DE1015039 120v/60Hz to 12v AC/DC converter TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 7 of 27

Device Details Description (Manufacturer, Type Model, OUT Code) Sample Name Description AC/DC converter AC/DC converter Evaluation test board u-blox, EVB-WL3, DE1015039 Evaluation test board Sample Name Description Evaluation test board Evaluation test board 3.4 AUXILIARY EQUIPMENT For the purposes of this test report, auxiliary equipment is defined as equipment which is used temporarily to enable operational and control features especially used for the tests of the EUT which is not used during normal operation or equipment that is used during the tests in combination with the EUT but is not subject of this test report. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Auxiliary Equipment can influence the test results. Device Details Description (Manufacturer, HW, SW, S/N) L17MB-P LG, -, -, 412WAPL0U560 TFT Display EMC TFT 5 Lifebook Eseries E781 Fujitsu, -, -, DSCK013817 Laptop RE M-BT58 Logitech, -, -, HC60915A2XC EMC MOUSE 1 PJW1942NA Fujitsu, -, -, 13300281B AC Adapter 3 Laptop RE RS 6000 USB ON CHERRY, -, -, G 0000273 2P28 EMC KEYBOARD 1 3.5 EUT SETUPS This chapter describes the combination of EUTs and equipment used for testing. The rationale for selecting the EUTs, ancillary and auxiliary equipment and interconnecting cables, is to test a representative configuration meeting the requirements of the referenced standards. Setup Combination of EUTs Description and Rationale Standard Sample, Standard radiated setup used for connecting module to a Evaluation test board, laptop computer (Windows 7 Pro) via USB. Continuous AC/DC converter, communication is maintained over the USB interface by the S01_AY02 L17MB-P, PJW1942NA, use of AT command scripts. Lifebook Eseries E781, M-BT58, RS 6000 USB ON, TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 8 of 27

3.6 OPERATING MODES This chapter describes the operating modes of the EUTs used for testing. 3.6.1TEST CHANNELS Testing performed in UMTS FDD4, Channel 20175 (1732.50 MHz) 3.7 PRODUCT LABELLING 3.7.1 FCC ID LABEL Please refer to the documentation of the applicant. 3.7.2 LOCATION OF THE LABEL ON THE EUT Please refer to the documentation of the applicant. TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 9 of 27

4 TEST RESULTS 4.1 CONDUCTED EMISSIONS AT AC MAINS Standard FCC Part 15 Subpart B The test was performed according to: ANSI C63.4 4.1.1 TEST DESCRIPTION The test set-up was made in accordance to the general provisions of ANSI C 63.4 The Equipment Under Test (EUT) was setup in a shielded room to perform the conducted emissions measurements in a typical installation configuration. The EUT was powered from 50µH || 50 Ohm Line Impedance Stabilization Network (LISN). The LISN’s unused connections were terminated with 50 Ohm loads. The measurement procedure consists of two steps. It is implemented into the EMI test software EMC-32 from R&S. Step 1: Preliminary scan Intention of this step is, to determine the conducted EMI-profile of the EUT. EMI receiver settings: - Detector: Peak – Maxhold & Average - Frequency range: 150 kHz – 30 MHz - Frequency steps: 2.5 kHz - IF–Bandwidth: 9 kHz - Measuring time / Frequency step: 100 ms (FFT-based) - Measurement on phase + neutral lines of the power cords On basis of this preliminary scan the highest amplitudes and the corresponding frequencies relative to the limit are identified. Emissions above the limit and emissions which are in the 10 dB range below the limit are considered. Step 2: Final measurement Intention of this step is, to determine the highest emissions with the settings defined in the test specification for the frequencies identified in step 1. EMI receiver settings: - Detector: Quasi-Peak - IF Bandwidth: 9 kHz - Measuring time: 1 s / frequency At each frequency determined in step 1, four measurements are performed in the following combinations: 1) Neutral lead - reference ground (PE grounded) 2) Phase lead - reference ground (PE grounded) 3) Neutral lead - reference ground (PE floating) 4) Phase lead - reference ground (PE floating) The highest value is reported. TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 10 of 27

4.1.2 TEST REQUIREMENTS / LIMITS FCC Part 15, Subpart B, §15.107 Class B: Frequency (MHz) QP Limits (dBµV) AV Limits (dBµV) 0.15 – 0.5 66 - 56 56 - 46 0.5 - 5 56 46 5 - 30 60 50 Class A: Frequency (MHz) QP Limits (dBµV) AV Limits (dBµV) 0.15 – 0.5 79 66 0.5 - 30 73 60 4.1.3 TEST PROTOCOL Power line PE Frequency [MHz] Level [dBµV] Detector Limit [dBµV] Margin [dB] L1 GND 0.4 38.4 AV 47.1 8.8 L1 GND 0.4 45.9 QP 57.1 11.2 N FL 4.2 36.5 QP 56.0 19.5 L1 GND 4.3 36.3 AV 46.0 9.7 N GND 5.0 35.1 QP 56.0 20.9 L1 GND 5.1 36.6 AV 50.0 13.4 L1 GND 15.4 35.7 AV 50.0 14.4 L1 GND 18.0 39.0 AV 50.0 11.0 L1 GND 18.0 40.6 QP 60.0 19.4 L1 GND 18.9 40.6 QP 60.0 19.4 L1 GND 18.9 38.2 AV 50.0 11.8 L1 GND 19.2 38.5 QP 60.0 21.5 L1 GND 19.7 37.3 QP 50.0 12.7 N GND 20.8 39.7 QP 60.0 20.3 N GND 22.3 35.6 AV 50.0 14.4 L1 GND 24.0 41.0 AV 50.0 9.1 L1 GND 24.0 42.6 QP 60.0 17.4 L1 GND 24.9 39.3 AV 50.0 10.7 L1 GND 24.9 42.1 QP 60.0 17.9 L1 GND 25.0 41.3 QP 60.0 18.7 TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 11 of 27

4.1.4 MEASUREMENT PLOT (SHOWING THE HIGHEST VALUE, “WORST CASE”) AC mains connection = via connected computer device, Test setup = computer peripheral 80 70 Limit_15_107_QP_ClassB 60 Limit_15_107_AV_ClassB 50 Level in dBµV 40 30 20 10 0 150k 300 400 500 800 1M 2M 3M 4M 5M 6 8 10M 20M 30M Frequency in Hz 4.1.5 TEST EQUIPMENT USED Conducted Emissions FCC TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 12 of 27

4.2 RADIATED EMISSIONS Standard FCC Part 15 Subpart B The test was performed according to: ANSI C63.4 4.2.1 TEST DESCRIPTION The test set-up was made in accordance to the general provisions of ANSI C63.4 in a typical installation configuration. The Equipment Under Test (EUT) was set up on a non-conductive table 1.0 x 2.0 m² in the semi-anechoic chamber. The influence of the EUT support table that is used between 30–1000 MHz was evaluated. The measurement procedure is implemented into the EMI test software EMC32 from R&S. Exploratory tests are performed at 3 orthogonal axes to determine the worst-case orientation of a body-worn or handheld EUT. The final test on all kind of EUTs is also performed at 3 axes. A pre-check is performed while the EUT is powered from a DC power source. 1. Measurement above 30 MHz and up to 1 GHz Step 1: Preliminary scan This is a preliminary test to identify the highest amplitudes relative to the limit. Settings for step 1: - Antenna distance: 3 m - Detector: Peak-Maxhold / Quasipeak (FFT-based) - Frequency range: 30 – 1000 MHz - Frequency steps: 30 kHz - IF–Bandwidth: 120 kHz - Measuring time / Frequency step: 100 ms - Turntable angle range: –180° to 90° - Turntable step size: 90° - Height variation range: 1 – 3 m - Height variation step size: 2 m - Polarisation: Horizontal + Vertical Intention of this step is, to determine the radiated EMI-profile of the EUT. Afterwards the relevant emissions for the final measurement are identified. Step 2: Adjustment measurement In this step the accuracy of the turntable azimuth and antenna height will be improved. This is necessary to find out the maximum value of every frequency. For each frequency, which was determined the turntable azimuth and antenna height will be adjusted. The turntable azimuth will slowly vary by ± 45° around this value. During this action, the value of emission is continuously measured. The turntable azimuth at the highest emission will be recorded and adjusted. In this position, the antenna height will also slowly vary by ± 100 cm around the antenna height determined. During this action, the value of emission is also continuously measured. The antenna height of the highest emission will also be recorded and adjusted. - Detector: Peak – Maxhold - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 100 ms - Turntable angle range: ± 45 ° around the determined value - Height variation range: ± 100 cm around the determined value - Antenna Polarisation: max. value determined in step 1 TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 13 of 27

Step 3: Final measurement with QP detector With the settings determined in step 3, the final measurement will be performed: EMI receiver settings for step 4: - Detector: Quasi-Peak (< 1 GHz) - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 1 s After the measurement a plot will be generated which contains a diagram with the results of the preliminary scan and a chart with the frequencies and values of the results of the final measurement. 3. Measurement above 1 GHz The following modifications apply to the measurement procedure for the frequency range above 1 GHz: Step 1: The Equipment Under Test (EUT) was set up on a non-conductive support (tilt device) at 1.5 m height in the fully-anechoic chamber. All steps were performed with one height (1.5 m) of the receiving antenna only. The EUT is turned during the preliminary measurement across the elevation axis, with a step size of 90 °. The turn table step size (azimuth angle) for the preliminary measurement is 45 °. Step 2: Due to the fact, that in this frequency range the test is performed in a fully anechoic room, the height scan of the receiving antenna instep 2 is omitted. Instead of this, a maximum search with a step size ± 45° for the elevation axis is performed. The turn table azimuth will slowly vary by ± 22.5°. The elevation angle will slowly vary by ± 45° EMI receiver settings (for all steps): - Detector: Peak, Average - IF Bandwidth = 1 MHz Step 3: Spectrum analyser settings for step 3: - Detector: Peak / Average - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 1 MHz - Measuring time: 1 s 4.2.2 TEST REQUIREMENTS / LIMITS FCC Part 15, Subpart B, §15.109, Radiated Emission Limits Class B: Measurement Frequency (MHz) Limit (µV/m) Limits (dBµV/m) distance (m) 30 – 88 100@3m 3 40.0@3m 88 – 216 150@3m 3 43.5@3m 216 – 960 200@3m 3 46.0@3m 960 - 26000 500@3m 3 54.0@3m 26000 - 40000 500@3m 1 54.0@3m Class A: Measurement Frequency (MHz) Limit (µV/m) Limits (dBµV/m) distance (m) 30 – 88 90@10m 3 39.1@10m 88 – 216 150@10m 3 43.5@10m TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 14 of 27

216 – 960 210@10m 3 46.4@10m 960 - 26000 300@10m 3 49.5@10m 26000 - 40000 300@10m 1 49.5@10m The measured values for Class A and for Class B (> 26 GHz) measurements are corrected with an inverse linear distance extrapolation factor (20 dB/decade). §15.35(b) ..., there is also a limit on the radio frequency emissions, as measured using instrumentation with a peak detector function, corresponding to 20 dB above the maximum permitted average limit.... Used conversion factor: Limit (dBµV/m) = 20 log (Limit (µV/m)/1µV/m) 4.2.3 TEST PROTOCOL Spurious Freq. Spurious Level RBW Limit Margin to Detector [MHz] [dBµV/m] [kHz] [dBµV/m] Limit [dB] 39.5 36.4 QP 120.0 40.0 3.6 48.5 30.6 QP 120.0 40.0 9.4 69.8 29.5 QP 120.0 40.0 10.5 82.1 25.9 QP 120.0 40.0 14.1 86.2 25.5 QP 120.0 40.0 14.5 117.7 28.8 QP 120.0 43.5 14.7 133.4 33.0 QP 120.0 43.5 10.5 194.8 36.3 QP 120.0 43.5 7.2 356.2 30.6 QP 120.0 46.0 15.4 Remark: Please see next sub-clause for the measurement plot. TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 15 of 27

4.2.4 MEASUREMENT PLOT (SHOWING THE HIGHEST VALUE, “WORST CASE”) AC mains connection = via connected computer device, Measurement range = 1 GHz - 10 GHz, Test setup = computer peripheral 104 100 95 90 85 80 75 Level in dBµV/m 70 65 60 55 50 45 40 35 30 24 1G 2G 3G 4G 5G 6 8 10G 13G Frequency in Hz AC mains connection = via connected computer device, Measurement range = 30 MHz - 1 GHz, Test setup = computer peripheral 60 FCC_15b_ClassB 50 40 Level in dBµV/m 30 20 10 0 30M 50 60 80 100M 200 300 400 500 800 1G Frequency in Hz 4.2.5TEST EQUIPMENT USED Radiated Emissions FAR Radiated Emissions SAC TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 16 of 27

5 TEST EQUIPMENT 1 Radiated Emissions FAR Lab to perform radiated emission tests i a fully anechoic room Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 1.1 WHKX 7.0/18G- High Pass Filter Wainwright 09 8SS 1.2 5HC3500/1800 High Pass Filter Trilithic 200035008 0-1.2-KK 1.3 Fully Anechoic 8.80m x 4.60m Albatross Projects P26971-647- Room x 4.05m (l x w 001-PRB x h) 1.4 TT 1.5 WI Turn Table Maturo GmbH - 1.5 Fluke 177 Digital Fluke Europe B.V. 86670383 2016-02 2018-02 Multimeter 03 (Multimeter) 1.6 Tilt device Antrieb TD1.5- Maturo GmbH TD1.5- Maturo 10kg 10kg/024/37907 (Rohacell) 09 1.7 5HC2700/1275 High Pass Filter Trilithic 9942012 0-1.5-KK 1.8 4HC1600/1275 High Pass Filter Trilithic 9942011 0-1.5-KK 1.9 ASP 1.2/1.8-10 Antenna Mast Maturo GmbH - kg 1.10 JS4-18002600- Broadband Miteq 849785 32-5P Amplifier 18 GHz - 26 GHz 1.11 JS4-00101800- Broadband Miteq 896037 35-5P Amplifier 30 MHz - 18 GHz 1.12 Opus10 THI ThermoHygro Lufft Mess- und 12482 2015-03 2017-03 (8152.00) Datalogger 12 Regeltechnik (Environ) GmbH 1.13 JS4-00102600- Broadband Miteq 619368 42-5A Amplifier 30 MHz - 26 GHz 1.14 FSW 43 Spectrum Rohde & Schwarz 103779 2014-11 2016-11 Analyzer 1.15 SMR 20 Signal Rohde & Schwarz 846834/008 2014-06 2017-06 Generator 1.16 HL 562 Ultralog Log.-per. Rohde & Schwarz 100609 2016-04 2019-04 Antenna 1.17 PAS 2.5 - 10 kg Antenna Mast Maturo GmbH - 1.18 HF 907 Double-ridged Rohde & Schwarz 102444 2015-05 2018-05 horn TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 17 of 27

2 Conducted Emissions FCC Conducted Emissions power line for FCC standards Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 2.1 ESH 3-Z5 Two-Line V- Rohde & Schwarz 828304/029 2015-03 2017-03 Network 2.2 ESR 7 EMI Receiver / Rohde & Schwarz 101424 2014-11 2016-11 Spectrum Analyzer 2.3 EP 1200/B, Amplifier with Spitzenberger & B6278 2015-07 2018-07 NA/B1 integrated Spieß variable Oscillator 2.4 Fluke 177 Digital Fluke Europe B.V. 86670383 2016-02 2018-02 Multimeter 03 (Multimeter) 2.5 Shielded Room Shielded Room Frankonia - 02 for conducted testing, 12qm 2.6 ESIB 26 Spectrum Rohde & Schwarz 830482/004 2015-12 2017-12 Analyzer 2.7 Opus10 THI ThermoHygro Lufft Mess- und 7489 2015-02 2017-02 (8152.00) Datalogger 02 Regeltechnik (Environ) GmbH 2.8 ESH 3-Z5 Two-Line V- Rohde & Schwarz 829996/002 2015-03 2017-03 Network 2.9 Opus10 TPR ThermoAirpres Lufft Mess- und 13936 2015-02 2017-02 (8253.00) sure Regeltechnik Datalogger 13 GmbH (Environ) 2.10 Chroma 6404 AC Power Chroma ATE INC. 64040001304 Source 3 Radiated Emissions SAC Lab to perform radiated emission tests in semi anechoic configuration Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 3.1 Anechoic 10.58 x 6.38 x Frankonia none 2014-01 2017-01 Chamber 6.00 m³ 3.2 Air compressor none none 3.3 MCU Controller Maturo GmbH 961208 Maturo 3.4 BB4312-C30- Filter Universal Siemens&Matsushit none H3x 1A a 3.5 CE-CAM/1 EMC camera CE-SYS none TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 18 of 27

Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 3.6 CO 2000 Controller Innco innovative CO2000/328/124 Innco 2000 constructions 70406/L GmbH 3.7 CCD-400E EMC camera Mitsubishi 0005033 Nr.2 3.8 B84312-C110- Filter ISDN Siemens&Matsushit none E1 a The calibration interval is the time interval between “Last Calibration” and “Calibration Due” TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 19 of 27

6 ANTENNA FACTORS, CABLE LOSS AND SAMPLE CALCULATIONS This chapter contains the antenna factors with their corresponding path loss of the used measurement path for all antennas as well as the insertion loss of the LISN. 6.1 LISN R&S ESH3-Z5 (150 KHZ – 30 MHZ) cable LISN loss insertion (incl. 10 loss dB ESH3- atten- Frequency Corr. Z5 uator) MHz dB dB dB 0,15 10,1 0,1 10,0 5 10,3 0,1 10,2 7 10,5 0,2 10,3 10 10,5 0,2 10,3 12 10,7 0,3 10,4 14 10,7 0,3 10,4 16 10,8 0,4 10,4 18 10,9 0,4 10,5 20 10,9 0,4 10,5 22 11,1 0,5 10,6 24 11,1 0,5 10,6 26 11,2 0,5 10,7 28 11,2 0,5 10,7 30 11,3 0,5 10,8 Sample calculation ULISN (dB µV) = U (dB µV) + Corr. (dB) U = Receiver reading LISN Insertion loss = Voltage Division Factor of LISN Corr. = sum of single correction factors of used LISN, cables, switch units (if used) Linear interpolation will be used for frequencies in between the values in the table. TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 20 of 27

6.2 ANTENNA R&S HFH2-Z2 (9 KHZ – 30 MHZ) cable cable cable cable distance dLimit dused loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. AF (inside (outside (switch (to (-40 dB/ distance distance Frequency HFH-Z2) Corr. chamber) chamber) unit) receiver) decade) (limit) (used) MHz dB (1/m) dB dB dB dB dB dB m m 0,009 20,50 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,01 20,45 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,015 20,37 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,02 20,36 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,025 20,38 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,03 20,32 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,05 20,35 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,08 20,30 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,1 20,20 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,2 20,17 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,3 20,14 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,49 20,12 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,490001 20,12 -39,6 0,1 0,1 0,1 0,1 -40 30 3 0,5 20,11 -39,6 0,1 0,1 0,1 0,1 -40 30 3 0,8 20,10 -39,6 0,1 0,1 0,1 0,1 -40 30 3 1 20,09 -39,6 0,1 0,1 0,1 0,1 -40 30 3 2 20,08 -39,6 0,1 0,1 0,1 0,1 -40 30 3 3 20,06 -39,6 0,1 0,1 0,1 0,1 -40 30 3 4 20,05 -39,5 0,2 0,1 0,1 0,1 -40 30 3 5 20,05 -39,5 0,2 0,1 0,1 0,1 -40 30 3 6 20,02 -39,5 0,2 0,1 0,1 0,1 -40 30 3 8 19,95 -39,5 0,2 0,1 0,1 0,1 -40 30 3 10 19,83 -39,4 0,2 0,1 0,2 0,1 -40 30 3 12 19,71 -39,4 0,2 0,1 0,2 0,1 -40 30 3 14 19,54 -39,4 0,2 0,1 0,2 0,1 -40 30 3 16 19,53 -39,3 0,3 0,1 0,2 0,1 -40 30 3 18 19,50 -39,3 0,3 0,1 0,2 0,1 -40 30 3 20 19,57 -39,3 0,3 0,1 0,2 0,1 -40 30 3 22 19,61 -39,3 0,3 0,1 0,2 0,1 -40 30 3 24 19,61 -39,3 0,3 0,1 0,2 0,1 -40 30 3 26 19,54 -39,3 0,3 0,1 0,2 0,1 -40 30 3 28 19,46 -39,2 0,3 0,1 0,3 0,1 -40 30 3 30 19,73 -39,1 0,4 0,1 0,3 0,1 -40 30 3 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) distance correction = -40 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 21 of 27

6.3 ANTENNA R&S HL562 (30 MHZ – 1 GHZ) (dLimit = 3 m) cable cable cable cable distance dLimit dused AF loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. R&S (inside (outside (switch (to (-20 dB/ distance distance Frequency HL562 Corr. chamber) chamber) unit) receiver) decade) (limit) (used) MHz dB (1/m) dB dB dB dB dB dB m m 30 18,6 0,6 0,29 0,04 0,23 0,02 0,0 3 3 50 6,0 0,9 0,39 0,09 0,32 0,08 0,0 3 3 100 9,7 1,2 0,56 0,14 0,47 0,08 0,0 3 3 150 7,9 1,6 0,73 0,20 0,59 0,12 0,0 3 3 200 7,6 1,9 0,84 0,21 0,70 0,11 0,0 3 3 250 9,5 2,1 0,98 0,24 0,80 0,13 0,0 3 3 300 11,0 2,3 1,04 0,26 0,89 0,15 0,0 3 3 350 12,4 2,6 1,18 0,31 0,96 0,13 0,0 3 3 400 13,6 2,9 1,28 0,35 1,03 0,19 0,0 3 3 450 14,7 3,1 1,39 0,38 1,11 0,22 0,0 3 3 500 15,6 3,2 1,44 0,39 1,20 0,19 0,0 3 3 550 16,3 3,5 1,55 0,46 1,24 0,23 0,0 3 3 600 17,2 3,5 1,59 0,43 1,29 0,23 0,0 3 3 650 18,1 3,6 1,67 0,34 1,35 0,22 0,0 3 3 700 18,5 3,6 1,67 0,42 1,41 0,15 0,0 3 3 750 19,1 4,1 1,87 0,54 1,46 0,25 0,0 3 3 800 19,6 4,1 1,90 0,46 1,51 0,25 0,0 3 3 850 20,1 4,4 1,99 0,60 1,56 0,27 0,0 3 3 900 20,8 4,7 2,14 0,60 1,63 0,29 0,0 3 3 950 21,1 4,8 2,22 0,60 1,66 0,33 0,0 3 3 1000 21,6 4,9 2,23 0,61 1,71 0,30 0,0 3 3 (dLimit = 10 m) 30 18,6 -9,9 0,29 0,04 0,23 0,02 -10,5 10 3 50 6,0 -9,6 0,39 0,09 0,32 0,08 -10,5 10 3 100 9,7 -9,2 0,56 0,14 0,47 0,08 -10,5 10 3 150 7,9 -8,8 0,73 0,20 0,59 0,12 -10,5 10 3 200 7,6 -8,6 0,84 0,21 0,70 0,11 -10,5 10 3 250 9,5 -8,3 0,98 0,24 0,80 0,13 -10,5 10 3 300 11,0 -8,1 1,04 0,26 0,89 0,15 -10,5 10 3 350 12,4 -7,9 1,18 0,31 0,96 0,13 -10,5 10 3 400 13,6 -7,6 1,28 0,35 1,03 0,19 -10,5 10 3 450 14,7 -7,4 1,39 0,38 1,11 0,22 -10,5 10 3 500 15,6 -7,2 1,44 0,39 1,20 0,19 -10,5 10 3 550 16,3 -7,0 1,55 0,46 1,24 0,23 -10,5 10 3 600 17,2 -6,9 1,59 0,43 1,29 0,23 -10,5 10 3 650 18,1 -6,9 1,67 0,34 1,35 0,22 -10,5 10 3 700 18,5 -6,8 1,67 0,42 1,41 0,15 -10,5 10 3 750 19,1 -6,3 1,87 0,54 1,46 0,25 -10,5 10 3 800 19,6 -6,3 1,90 0,46 1,51 0,25 -10,5 10 3 850 20,1 -6,0 1,99 0,60 1,56 0,27 -10,5 10 3 900 20,8 -5,8 2,14 0,60 1,63 0,29 -10,5 10 3 950 21,1 -5,6 2,22 0,60 1,66 0,33 -10,5 10 3 1000 21,6 -5,6 2,23 0,61 1,71 0,30 -10,5 10 3 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) distance correction = -20 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Tables show an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 22 of 27

6.4 ANTENNA R&S HF907 (1 GHZ – 18 GHZ) cable cable loss 3 loss 1 (switch (relay + cable unit, AF cable loss 2 atten- cable R&S inside (outside uator & loss 4 (to Frequency HF907 Corr. chamber) chamber) pre-amp) receiver) MHz dB (1/m) dB dB dB dB dB 1000 24,4 -19,4 0,99 0,31 -21,51 0,79 2000 28,5 -17,4 1,44 0,44 -20,63 1,38 3000 31,0 -16,1 1,87 0,53 -19,85 1,33 4000 33,1 -14,7 2,41 0,67 -19,13 1,31 5000 34,4 -13,7 2,78 0,86 -18,71 1,40 6000 34,7 -12,7 2,74 0,90 -17,83 1,47 7000 35,6 -11,0 2,82 0,86 -16,19 1,46 cable loss 4 cable (switch loss 1 cable cable unit, used AF (relay loss 2 loss 3 atten- cable for R&S inside (inside (outside uator & loss 5 (to FCC Frequency HF907 Corr. chamber) chamber) chamber) pre-amp) receiver) 15.247 MHz dB (1/m) dB dB dB dB dB dB 3000 31,0 -23,4 0,47 1,87 0,53 -27,58 1,33 4000 33,1 -23,3 0,56 2,41 0,67 -28,23 1,31 5000 34,4 -21,7 0,61 2,78 0,86 -27,35 1,40 6000 34,7 -21,2 0,58 2,74 0,90 -26,89 1,47 7000 35,6 -19,8 0,66 2,82 0,86 -25,58 1,46 cable loss 1 cable cable cable cable cable AF (relay loss 2 loss 3 loss 4 loss 5 loss 6 R&S inside (High (pre- (inside (outside (to Frequency HF907 Corr. chamber) Pass) amp) chamber) chamber) receiver) MHz dB (1/m) dB dB dB dB dB dB dB 7000 35,6 -57,3 0,56 1,28 -62,72 2,66 0,94 1,46 8000 36,3 -56,3 0,69 0,71 -61,49 2,84 1,00 1,53 9000 37,1 -55,3 0,68 0,65 -60,80 3,06 1,09 1,60 10000 37,5 -56,2 0,70 0,54 -61,91 3,28 1,20 1,67 11000 37,5 -55,3 0,80 0,61 -61,40 3,43 1,27 1,70 12000 37,6 -53,7 0,84 0,42 -59,70 3,53 1,26 1,73 13000 38,2 -53,5 0,83 0,44 -59,81 3,75 1,32 1,83 14000 39,9 -56,3 0,91 0,53 -63,03 3,91 1,40 1,77 15000 40,9 -54,1 0,98 0,54 -61,05 4,02 1,44 1,83 16000 41,3 -54,1 1,23 0,49 -61,51 4,17 1,51 1,85 17000 42,8 -54,4 1,36 0,76 -62,36 4,34 1,53 2,00 18000 44,2 -54,7 1,70 0,53 -62,88 4,41 1,55 1,91 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. Tables show an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 23 of 27

6.5 ANTENNA EMCO 3160-09 (18 GHZ – 26.5 GHZ) cable cable cable cable cable AF loss 1 loss 2 loss 3 loss 4 loss 5 EMCO (inside (pre- (inside (switch (to Frequency 3160-09 Corr. chamber) amp) chamber) unit) receiver) MHz dB (1/m) dB dB dB dB dB dB 18000 40,2 -23,5 0,72 -35,85 6,20 2,81 2,65 18500 40,2 -23,2 0,69 -35,71 6,46 2,76 2,59 19000 40,2 -22,0 0,76 -35,44 6,69 3,15 2,79 19500 40,3 -21,3 0,74 -35,07 7,04 3,11 2,91 20000 40,3 -20,3 0,72 -34,49 7,30 3,07 3,05 20500 40,3 -19,9 0,78 -34,46 7,48 3,12 3,15 21000 40,3 -19,1 0,87 -34,07 7,61 3,20 3,33 21500 40,3 -19,1 0,90 -33,96 7,47 3,28 3,19 22000 40,3 -18,7 0,89 -33,57 7,34 3,35 3,28 22500 40,4 -19,0 0,87 -33,66 7,06 3,75 2,94 23000 40,4 -19,5 0,88 -33,75 6,92 3,77 2,70 23500 40,4 -19,3 0,90 -33,35 6,99 3,52 2,66 24000 40,4 -19,8 0,88 -33,99 6,88 3,88 2,58 24500 40,4 -19,5 0,91 -33,89 7,01 3,93 2,51 25000 40,4 -19,3 0,88 -33,00 6,72 3,96 2,14 25500 40,5 -20,4 0,89 -34,07 6,90 3,66 2,22 26000 40,5 -21,3 0,86 -35,11 7,02 3,69 2,28 26500 40,5 -21,1 0,90 -35,20 7,15 3,91 2,36 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 24 of 27

6.6 ANTENNA EMCO 3160-10 (18 GHZ – 26.5 GHZ) cable cable cable cable distance dLimit dused AF loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. EMCO (inside (outside (switch (to (-20 dB/ distance distance Frequency 3160-10 Corr. chamber) chamber) unit) receiver) decade) (limit) (used) GHz dB (1/m) dB dB dB dB dB dB m m 26,5 43,4 -11,2 4,4 -15,6 3 0,5 27,0 43,4 -11,2 4,4 -15,6 3 0,5 28,0 43,4 -11,1 4,5 -15,6 3 0,5 29,0 43,5 -11,0 4,6 -15,6 3 0,5 30,0 43,5 -10,9 4,7 -15,6 3 0,5 31,0 43,5 -10,8 4,7 -15,6 3 0,5 32,0 43,5 -10,7 4,8 -15,6 3 0,5 33,0 43,6 -10,7 4,9 -15,6 3 0,5 34,0 43,6 -10,6 5,0 -15,6 3 0,5 35,0 43,6 -10,5 5,1 -15,6 3 0,5 36,0 43,6 -10,4 5,1 -15,6 3 0,5 37,0 43,7 -10,3 5,2 -15,6 3 0,5 38,0 43,7 -10,2 5,3 -15,6 3 0,5 39,0 43,7 -10,2 5,4 -15,6 3 0,5 40,0 43,8 -10,1 5,5 -15,6 3 0,5 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolarisation will be used for frequencies in between the values in the table. distance correction = -20 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 25 of 27

layers A Bureau Veritas Group Company 7 SETUP DRAWINGS 1—4 m height Anechoic Chamber Equipment RX Antenna under Test Turntable Turntable Controller Mast Digital Communication Controller Tester connected Spectrum to Equipment Analyzer under Test Remark: Depending on the frequency range suitable antenna types, attenuators or preamplifiers are used, Setup in the Anechoic chamber. For measurements below 1 GHz the ground was replaced by a conducting ground plane. LILSN Analyzer Signaling EUT 1| unit Setup in the shielded room for conducted measurements at AC mains port TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 26 of 27

8 MEASUREMENT UNCERTAINTIES Test Case Parameter Uncertainty Conducted Emissions at AC mains Voltage ± 3.4 dB Radiated Emissions Field Strength ± 5.5 dB 9 PHOTO REPORT Please see separate photo report. TEST REPORT REFERENCE: MDE_UBLOX_1603_FCCb Page 27 of 27


Document Created: 2019-09-21 08:33:42
Document Modified: 2019-09-21 08:33:42
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC