Modular Approval Checklist

FCC ID: XMR201909EC25AFX

Cover Letter(s)

Download: PDF
FCCID_4463085

Quectel Wireless Solutions Company Limited Declaration of the Modular Approval Applicant / Grantee Quectel Wireless Solutions Co., Ltd FCC ID: XMR201909EC25AFX Model: EC25-AFX; EC25-AFX MINIPCIE The single module transmitter has been evaluated then tested meeting the requirements under Part 15C Section 212 as below: Modular approval requirement EUT Condition Comply (a) The radio elements of the modular transmitter The radio elements of the YES must have their own shielding. The physical modular transmitter have their crystal and tuning capacitors may be located own shielding. external to the shielded radio elements. (b) The modular transmitter must have The modular has buffered data YES buffered modulation/data inputs (if such inputs are inputs, it is integrated in chip. provided) to ensure that the module will comply Please see schematic.pdf with part 15 requirements under conditions of excessive data rates or over-modulation. (c)The modular transmitter must have its All power lines derived from the YES own power supply regulation. host device are regulated before energizing other circuits internal to the EC25-AFX; EC25-AFX MINIPCIE. Please see schematic.pdf (d) The modular transmitter must comply A permanently attached antenna Not with the antenna and transmission system or unique antenna connector is Applicable requirements of Sections 15.203, 15.204(b) and not a requirement for licensed 15.204(c). The antenna must either be modules. permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. (e)The modular transmitter must be tested The EC25-AFX; EC25-AFX YES in a stand-alone configuration, i.e., the module MINIPCIE was tested in a stand must not be inside another device during testing for ‐alone configuration via a compliance with part 15 requirements. Unless PCMCIA extender. Please see the transmitter module will be battery powered, it spurious set‐up must comply with the AC line conducted

Quectel Wireless Solutions Company Limited requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see Section 15.31(i)) must not be in side another device during testing. (f)The modular transmitter must be The label position of EC25-AFX; YES equipped with either a permanently affixed label EC25-AFX MINIPCIE is clearly or must be capable of electronically displaying its FCC identification number. indicated. If the FCC ID of the module cannot be seen when it is installed, then the host label must include the text: Contains FCC ID: XMR201909EC25AFX. Please see the label.pdf (g) The modular transmitter must comply The EC25-AFX; EC25-AFX YES with any specific rules or operating requirements MINIPCIE is compliant with all that ordinarily apply to a complete transmitter and applicable FCC rules. Detail the manufacturer must provide adequate instructions are given in the User instructions along with the module to explain any Manual. suchrequirements. A copy of these instructions must be included in the application for equipmentauthorizationrequirements,whicharebas edon theintendeduse/configurations. (h)The modular transmitter must comply The EC25-AFX; EC25-AFX YES with any applicable RF exposure requirements in MINIPCIE is approved to its final configuration. comply with the applicable RF exposure requirement, please see the MPE evaluation with 20cm as the distance restriction.

Quectel Wireless Solutions Company Limited Dated 2019/9/17 By: Johnny Xiang Signature Printed Title: Project Manager On behalf of : Quectel Wireless Solutions Company Limited Telephone: +86-2150086326-800


Document Created: 2019-09-17 17:32:08
Document Modified: 2019-09-17 17:32:08
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC