Modular approval letter

FCC ID: XMR201907EG91VX

Cover Letter(s)

Download: PDF
FCCID_4333403

Quectel Wireless Solutions Company Limited Declaration of the Modular Approval Applicant / Grantee Quectel Wireless Solutions Company Limited FCC ID: XMR201907EG91VX Model: EG91-VX The single module transmitter has been evaluated then tested meeting the requirements under Part 15C Section 212 as below: Modular approval requirement EUT Condition Comply (a) The radio elements of the modular transmitter must have The radio elements of the modular YES their own shielding. The physical crystal and tuning transmitter have their own shielding. capacitors may be located external to the shielded radio elements. (b) The modular transmitter must have The modular has buffered data YES buffered modulation/data inputs (if such inputs are inputs, it is integrated in chip. Please provided) to ensure that the module will comply with part 15 see schematic.pdf requirements under conditions of excessive data rates or over-modulation. (c)The modular transmitter must have its All power lines derived from the host YES own power supply regulation. device are regulated before energizing other circuits internal to the EG91-VX. Please see schematic.pdf (d) The modular transmitter must comply A permanently attached antenna or YES with the antenna and transmission system requirements of unique antenna connector is not a Sections 15.203, 15.204(b) and 15.204(c). The antenna requirement for licensed modules. must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. (e)The modular transmitter must be tested The EG91-VX was tested in a YES in a stand-alone configuration, i.e., the module must not be stand‐alone configuration via a inside another device during testing for compliance with part PCMCIA extender. Please see 15 requirements. Unless the transmitter module will be spurious set‐up battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the 7th Floor, Hongye Building, No.1801 Hongmei Road, Xuhui District, Shanghai 200233, ChinaEmail: info@quectel.comWebsite: www.quectel.compage 1

Quectel Wireless Solutions Company Limited module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see Section 15.31(i))mustnotbeinsideanotherdeviceduringtesting. (f)The modular transmitter must be The label position of EG91-VX is YES equipped with either a permanently affixed label or must clearly indicated. If the FCC ID of the be capable of electronically displaying its FCC identification number. module cannot be seen when it is installed, then the host label must include the text: Contains FCC ID: XMR201907EG91VX. Please see the label.pdf (g) The modular transmitter must comply The EG91-VX is compliant with all YES with any specific rules or operating requirements that applicable FCC rules. Detail ordinarily apply to a complete transmitter and the instructions are given in the User manufacturer must provide adequate instructions along Manual. with the module to explain any suchrequirements. A copy of these instructions must be included in the application for equipmentauthorizationrequirements,whicharebasedonthei ntendeduse/configurations. (h)The modular transmitter must comply The EG91-VX is approved to comply YES with any applicable RF exposure requirements in its final with the applicable RF exposure configuration. requirement, please see the MPE evaluation with 20cm as the distance restriction. ___________________________________ Johnny Xiang Quectel Wireless Solutions Company Limited Tel: +8602150086326 Fax: +862153253668 E-mail: johnny.xiang@quectel.com 7th Floor, Hongye Building, No.1801 Hongmei Road, Xuhui District, Shanghai 200233, ChinaEmail: info@quectel.comWebsite: www.quectel.compage 2


Document Created: 2019-06-20 15:19:23
Document Modified: 2019-06-20 15:19:23
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC