Test report

FCC ID: XMR201907AG35E

Test Report

Download: PDF
FCCID_4356416

RF Test Report Report No. : FG950911A RF Test Report APPLICANT : Quectel Wireless Solutions Co., Ltd. EQUIPMENT : LTE Module BRAND NAME : Quectel MODEL NAME : AG35-E FCC ID : XMR201907AG35E STANDARD : FCC 47 CFR Part 2, 22(H) CLASSIFICATION : Licensed Non-Broadcast Station Transmitter (TNB) The product was received on Nov. 05, 2018 and completely tested on Nov. 23, 2018. We, Sporton International (Kunshan) Inc., would like to declare that the tested sample has been evaluated in accordance with the procedures given in ANSI C63.26-2015 and shown compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of Sporton International (Kunshan) Inc., the test report shall not be reproduced except in full. Reviewed by: Jason Jia / Supervisor Approved by: James Huang / Manager Sporton International (Kunshan) Inc. No. 1098, Pengxi North Road, Kunshan Economic Development Zone Jiangsu Province 215300 People’s Republic of China Sporton International (Kunshan) Inc. Page Number : 1 of 21 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E Report Template No.: BU5-FG22 Version 2.0

RF Test Report Report No. : FG950911A TABLE OF CONTENTS REVISION HISTORY.......................................................................................................................................... 3 SUMMARY OF TEST RESULT ......................................................................................................................... 4 1 GENERAL DESCRIPTION .......................................................................................................................... 5 1.1 Applicant ............................................................................................................................................ 5 1.2 Product Feature of Equipment Under Test ....................................................................................... 5 1.3 Product Specification of Equipment Under Test ............................................................................... 6 1.4 Modification of EUT ........................................................................................................................... 6 1.5 Maximum Conducted Power, Frequency Tolerance, and Emission Designator ............................... 7 1.6 Testing Location ................................................................................................................................ 7 1.7 Applicable Standards ........................................................................................................................ 7 2 TEST CONFIGURATION OF EQUIPMENT UNDER TEST ........................................................................ 8 2.1 Test Mode.......................................................................................................................................... 8 2.2 Connection Diagram of Test System ................................................................................................ 9 2.3 Support Unit used in test configuration ............................................................................................. 9 2.4 Measurement Results Explanation Example .................................................................................... 9 2.5 Frequency List of Low/Middle/High Channels ................................................................................. 10 3 CONDUCTED TEST RESULT................................................................................................................... 11 3.1 Measuring Instruments .................................................................................................................... 11 3.2 Test Setup ....................................................................................................................................... 11 3.3 Test Result of Conducted Test ........................................................................................................ 11 3.4 Conducted Output Power and ERP/EIRP ....................................................................................... 12 3.5 Peak-to-Average Ratio .................................................................................................................... 13 3.6 99% Occupied Bandwidth and 26dB Bandwidth Measurement...................................................... 14 3.7 Conducted Band Edge .................................................................................................................... 15 3.8 Conducted Spurious Emission ........................................................................................................ 16 3.9 Frequency Stability .......................................................................................................................... 17 4 RADIATED TEST ITEMS .......................................................................................................................... 18 4.1 Measuring Instruments .................................................................................................................... 18 4.2 Test Setup ....................................................................................................................................... 18 4.3 Test Result of Radiated Test ........................................................................................................... 18 4.4 Field Strength of Spurious Radiation Measurement ....................................................................... 19 5 LIST OF MEASURING EQUIPMENT ........................................................................................................ 20 6 UNCERTAINTY OF EVALUATION ........................................................................................................... 21 APPENDIX A. TEST RESULTS OF CONDUCTED TEST APPENDIX B. TEST RESULTS OF RADIATED TEST APPENDIX C. TEST SETUP PHOTOGRAPHS Sporton International (Kunshan) Inc. Page Number : 2 of 21 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E Report Template No.: BU5-FG22 Version 2.0

RF Test Report Report No. : FG950911A REVISION HISTORY REPORT NO. VERSION DESCRIPTION ISSUED DATE FG950911A Rev. 01 Initial issue of report Jul. 11, 2019 Sporton International (Kunshan) Inc. Page Number : 3 of 21 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E Report Template No.: BU5-FG22 Version 2.0

RF Test Report Report No. : FG950911A SUMMARY OF TEST RESULT Report FCC Rule Description Limit Result Remark Section Conducted Output §2.1046 Reporting Only PASS - Power 3.4 Effective Radiated §22.913(a)(5) < 7 Watts PASS - Power Peak-to-Average 3.5 N/A < 13 dB PASS - Ratio 3.6 §2.1049 Occupied Bandwidth Reporting Only PASS - §2.1051 Band Edge 3.7 < 43+10log10(P[Watts]) PASS - §22.917(a) Measurement §2.1051 3.8 Conducted Emission < 43+10log10(P[Watts]) PASS - §22.917(a) Frequency Stability §2.1055 3.9 for Temperature & < 2.5 ppm for Part 22H PASS - §22.355 Voltage Under limit §2.1053 Field Strength of 4.4 < 43+10log10(P[Watts]) PASS 48.94 dB at §22.917(a) Spurious Radiation 1672.00 MHz Sporton International (Kunshan) Inc. Page Number : 4 of 21 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E Report Template No.: BU5-FG22 Version 2.0

RF Test Report Report No. : FG950911A 1 General Description 1.1 Applicant Quectel Wireless Solutions Co., Ltd. 7th Floor, Hongye Building, No.1801 Hongmei Road, Xuhui District, Shanghai 200233, China 1.2 Product Feature of Equipment Under Test Product Feature Equipment LTE Module Brand Name Quectel Model Name AG35-E FCC ID XMR201907AG35E GSM/GPRS/EGPRS/WCDMA/HSPA/DC-HSDPA EUT supports Radios application HSPA+ (16QAM uplink is not supported)/LTE HW Version R1.0 SW Version AG35EVAR08A01T4G EUT Stage Identical Prototype Remark: The above EUT's information was declared by manufacturer. Please refer to the specifications or user's manual for more detailed description. Sporton International (Kunshan) Inc. Page Number : 5 of 21 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E Report Template No.: BU5-FG22 Version 2.0

RF Test Report Report No. : FG950911A 1.3 Product Specification of Equipment Under Test Standards-related Product Specification WCDMA: Tx Frequency Band V: 826.4 MHz ~ 846.6 MHz WCDMA: Rx Frequency Band V: 871.4 MHz ~ 891.6 MHz WCDMA: Maximum Output Power to Antenna Band V: 23.72 dBm Antenna Type Fixed External Antenna Antenna Gain Cellular Band: 2 dBi WCDMA : BPSK (Uplink) HSDPA/DC-HSDPA : QPSK (Uplink) Type of Modulation HSUPA : QPSK (Uplink) HSPA+ : 16QAM(16QAM is not support uplink) DC-HSDPA : 64QAM 1.4 Modification of EUT No modifications are made to the EUT during all test items. Sporton International (Kunshan) Inc. Page Number : 6 of 21 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E Report Template No.: BU5-FG22 Version 2.0

RF Test Report Report No. : FG950911A 1.5 Maximum Conducted Power, Frequency Tolerance, and Emission Designator Maximum Frequency Type of Emission FCC Rule System Conducted Tolerance Modulation Designator (W) (ppm) Part 22 WCDMA Band V RMC 12.2Kbps BPSK 0.2355 0.0418 ppm 4M14F9W 1.6 Testing Location Sporton International (Kunshan) Inc. is accredited to ISO/IEC 17025:2017 by American Association for Laboratory Accreditation with Certificate Number 5145.02. Test Firm Sporton International (Kunshan) Inc. No. 1098, Pengxi North Road, Kunshan Economic Development Zone Jiangsu Province 215300 People’s Republic of China Test Site Location TEL : +86-512-57900158 FAX : +86-512-57900958 Sporton Site No. FCC Designation No. FCC Test Firm Registration No. Test Site No. 03CH06-KS CN1257 314309 TH01-KS 1.7 Applicable Standards According to the specifications of the manufacturer, the EUT must comply with the requirements of the following standards:  47 CFR Part 2, 22(H)  ANSI C63.26-2015  FCC KDB 971168 D01 Power Meas. License Digital Systems v03r01  FCC KDB 412172 D01 Determining ERP and EIRP v01r01 Remark: All test items were verified and recorded according to the standards and without any deviation during the test. Sporton International (Kunshan) Inc. Page Number : 7 of 21 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E Report Template No.: BU5-FG22 Version 2.0

RF Test Report Report No. : FG950911A 2 Test Configuration of Equipment Under Test 2.1 Test Mode Antenna port conducted and radiated test items were performed according to KDB 971168 D01 Power Meas. License Digital Systems v03r01 with maximum output power. Radiated measurements were performed with rotating EUT in different three orthogonal test planes to find the maximum emission. Radiated emissions were investigated as following frequency range: 1. 30 MHz to 9000 MHz for GSM850 and WCDMA Band V. All modes and data rates and positions were investigated. Test modes are chosen to be reported as the worst case configuration below: Test Modes Band Radiated TCs Conducted TCs WCDMA Band V  RMC 12.2Kbps Link  RMC 12.2Kbps Link Sporton International (Kunshan) Inc. Page Number : 8 of 21 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E Report Template No.: BU5-FG22 Version 2.0

RF Test Report Report No. : FG950911A 2.2 Connection Diagram of Test System System BT AP router Notebook GPS Station Simulator Earphone Power EUT Notebook Source Cradle Earphone iPod WLAN AP Monitor This example is connection diagram of EUT test configurations. . For detail, please refer to test mode configuration and setup photographs for each test item. 2.3 Support Unit used in test configuration Item Equipment Trade Name Model No. FCC ID Data Cable Power Cord 1. System Simulator Anritsu MT8820C N/A Unshielded,1.8m Anritsu Unshielded, 1.8 2. DC Power Supply GW INSTEK GPS-3030D N/A N/A m 2.4 Measurement Results Explanation Example For all conducted test items: The offset level is set in the spectrum analyzer to compensate the RF cable loss and attenuator factor between RF conducted output port and spectrum analyzer. With the offset compensation, the spectrum analyzer reading level will be exactly the RF output level. The spectrum analyzer offset is derived from RF cable loss and attenuator factor. Offset = RF cable loss + attenuator factor. The following shows an offset computation example with RF cable loss 4.4 dB and a 10dB attenuator. Example : Offset(dB) = RF cable loss(dB) + attenuator factor(dB). = 4.4 + 10 = 14.4 (dB) Sporton International (Kunshan) Inc. Page Number : 9 of 21 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E Report Template No.: BU5-FG22 Version 2.0

RF Test Report Report No. : FG950911A 2.5 Frequency List of Low/Middle/High Channels Frequency List Band Channel/Frequency(MHz) Lowest Middle Highest WCDMA Channel 4132 4182 4233 Band V Frequency 826.4 836.4 846.6 Sporton International (Kunshan) Inc. Page Number : 10 of 21 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E Report Template No.: BU5-FG22 Version 2.0

RF Test Report Report No. : FG950911A 3 Conducted Test Result 3.1 Measuring Instruments See list of measuring instruments of this test report. 3.2 Test Setup 3.2.1 Conducted Output Power 3.2.2 Peak-to-Average Ratio, Occupied Bandwidth, Conducted Band-Edge and Conducted Spurious Emission 3.2.3 Frequency Stability 3.3 Test Result of Conducted Test Please refer to Appendix A. Sporton International (Kunshan) Inc. Page Number : 11 of 21 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E Report Template No.: BU5-FG22 Version 2.0

RF Test Report Report No. : FG950911A 3.4 Conducted Output Power and ERP/EIRP 3.4.1 Description of the Conducted Output Power and ERP/EIRP A system simulator was used to establish communication with the EUT. Its parameters were set to enforce EUT transmitting at the maximum power. The measured power in the radio frequency on the transmitter output terminals shall be reported. The ERP of mobile transmitters must not exceed 7 Watts WCDMA Band V. According to KDB 412172 D01 Power Approach, EIRP = PT + GT – LC, ERP = EIRP -2.15, where PT = transmitter output power in dBm GT = gain of the transmitting antenna in dBi LC = signal attenuation in the connecting cable between the transmitter and antenna in dB 3.4.2 Test Procedures 1. The testing follows ANSI C63.26 Section 5.2 2. The transmitter output port was connected to the system simulator. 3. Set EUT at maximum power through the system simulator. 4. Select lowest, middle, and highest channels for each band and different modulation. 5. Measure and record the power level from the system simulator. Sporton International (Kunshan) Inc. Page Number : 12 of 21 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E Report Template No.: BU5-FG22 Version 2.0

RF Test Report Report No. : FG950911A 3.5 Peak-to-Average Ratio 3.5.1 Description of the PAR Measurement The peak-to-average ratio (PAR) of the transmission may not exceed 13 dB. 3.5.2 Test Procedures 1. The testing follows ANSI C63.26 Section 5.2.3.4 (CCDF). 2. The EUT was connected to spectrum and system simulator via a power divider. 3. Set the CCDF (Complementary Cumulative Distribution Function) option in spectrum analyzer. 4. The highest RF powers were measured and recorded the maximum PAPR level associated with a probability of 0.1 %. 5. Record the deviation as Peak to Average Ratio. Sporton International (Kunshan) Inc. Page Number : 13 of 21 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E Report Template No.: BU5-FG22 Version 2.0

RF Test Report Report No. : FG950911A 3.6 99% Occupied Bandwidth and 26dB Bandwidth Measurement 3.6.1 Description of 99% Occupied Bandwidth and 26dB Bandwidth Measurement The occupied bandwidth is the width of a frequency band such that, below the lower and above the upper frequency limits, the mean powers emitted are each equal to a specified percentage 0.5% of the total mean transmitted power. The 26 dB emission bandwidth is defined as the frequency range between two points, one above and one below the carrier frequency, at which the spectral density of the emission is attenuated 26 dB below the maximum in-band spectral density of the modulated signal. Spectral density (power per unit bandwidth) is to be measured with a detector of resolution bandwidth equal to approximately 1.0% of the emission bandwidth. 3.6.2 Test Procedures 1. The testing follows ANSI C63.26 Section 5.4 2. The EUT was connected to spectrum analyzer and system simulator via a power divider. 3. The spectrum analyzer center frequency is set to the nominal EUT channel center frequency. The span range for the spectrum analyzer shall be between two and five times the anticipated OBW. 4. The nominal resolution bandwidth (RBW) shall be in the range of 1 to 5 % of the anticipated OBW, and the VBW shall be at least 3 times the RBW. 5. Set the detection mode to peak, and the trace mode to max hold. 6. Determine the reference value: Set the EUT to transmit a modulated signal. Allow the trace to stabilize. Set the spectrum analyzer marker to the highest level of the displayed trace. (this is the reference value) 7. Determine the “-26 dB down amplitude” as equal to (Reference Value – X). 8. Place two markers, one at the lowest and the other at the highest frequency of the envelope of the spectral display such that each marker is at or slightly below the “–X dB down amplitude” determined in step 6. If a marker is below this “-X dB down amplitude” value it shall be placed as close as possible to this value. The OBW is the positive frequency difference between the two markers. 9. Use the 99 % power bandwidth function of the spectrum analyzer and report the measured bandwidth. Sporton International (Kunshan) Inc. Page Number : 14 of 21 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E Report Template No.: BU5-FG22 Version 2.0

RF Test Report Report No. : FG950911A 3.7 Conducted Band Edge 3.7.1 Description of Conducted Band Edge Measurement The power of any emission outside of the authorized operating frequency ranges must be lower than the transmitter power (P) by a factor of at least 43 + 10 log (P) dB. 3.7.2 Test Procedures 1. The testing follows ANSI C63.26 section 5.7 2. The EUT was connected to the spectrum analyzer and system simulator via a power divider. 3. The RF output of EUT was connected to the spectrum analyzer by an RF cable and attenuator. The path loss was compensated to the results for each measurement. 4. The band edges of low and high channels for the highest RF powers were measured. 5. The RF fundamental frequency should be excluded against the limit line in the operating frequency band. 6. The limit line is derived from 43 + 10log(P) dB below the transmitter power P(Watts) Sporton International (Kunshan) Inc. Page Number : 15 of 21 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E Report Template No.: BU5-FG22 Version 2.0

RF Test Report Report No. : FG950911A 3.8 Conducted Spurious Emission 3.8.1 Description of Conducted Spurious Emission Measurement The power of any emission outside of the authorized operating frequency ranges must be lower than the transmitter power (P) by a factor of at least 43 + 10 log (P) dB. It is measured by means of a calibrated spectrum analyzer and scanned from 30 MHz up to a th frequency including its 10 harmonic. 3.8.2 Test Procedures 1. The testing follows ANSI C63.26 section 5.7 2. The EUT was connected to the spectrum analyzer and system simulator via a power divider. 3. The RF output of EUT was connected to the spectrum analyzer by an RF cable and attenuator. The path loss was compensated to the results for each measurement. 4. The middle channel for the highest RF power within the transmitting frequency was measured. 5. The conducted spurious emission for the whole frequency range was taken. 6. The RF fundamental frequency should be excluded against the limit line in the operating frequency band. 7. The limit line is derived from 43 + 10log(P) dB below the transmitter power P(Watts) Sporton International (Kunshan) Inc. Page Number : 16 of 21 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E Report Template No.: BU5-FG22 Version 2.0

RF Test Report Report No. : FG950911A 3.9 Frequency Stability 3.9.1 Description of Frequency Stability Measurement The frequency stability shall be measured by variation of ambient temperature and variation of primary supply voltage to ensure that the fundamental emission stays within the authorized frequency block. The frequency stability of the transmitter shall be maintained within ±0.00025% (±2.5ppm) of the center frequency. 3.9.2 Test Procedures for Temperature Variation 1. The testing follows ANSI C63.26 section 5.6.4 2. The EUT was set up in the thermal chamber and connected with the system simulator. 3. With power OFF, the temperature was decreased to -30°C and the EUT was stabilized before testing. Power was applied and the maximum change in frequency was recorded within one minute. 4. With power OFF, the temperature was raised in 10°C step up to 50°C. The EUT was stabilized at each step for at least half an hour. Power was applied and the maximum frequency change was recorded within one minute. 3.9.3 Test Procedures for Voltage Variation 1. The testing follows ANSI C63.26 section 5.6.5 2. The EUT was placed in a temperature chamber at 20±5°C and connected with the system simulator. 3. The power supply voltage to the EUT was varied from 85% to 115% of the nominal value for other than hand carried battery equipment. 4. For hand carried, battery powered equipment, reduce the primary ac or dc supply voltage to the battery operating end point, which shall be specified by the manufacturer. 5. The variation in frequency was measured for the worst case. Sporton International (Kunshan) Inc. Page Number : 17 of 21 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E Report Template No.: BU5-FG22 Version 2.0

RF Test Report Report No. : FG950911A 4 Radiated Test Items 4.1 Measuring Instruments See list of measuring instruments of this test report. 4.2 Test Setup 4.2.1 For radiated test from 30MHz to 1GHz 4.2.2 For radiated test above 1GHz 4.3 Test Result of Radiated Test Please refer to Appendix B. Sporton International (Kunshan) Inc. Page Number : 18 of 21 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E Report Template No.: BU5-FG22 Version 2.0

RF Test Report Report No. : FG950911A 4.4 Field Strength of Spurious Radiation Measurement 4.4.1 Description of Field Strength of Spurious Radiated Measurement The power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitter power (P) by a factor of at least 43 + 10 log (P) dB. The spectrum is scanned from 30 MHz up to a frequency including its 10th harmonic. 4.4.2 Test Procedures 1. The testing follows ANSI C63.26 Section 5.5 2. The EUT was placed on a rotatable wooden table 0.8 meters for frequency below 1GHz and 1.5 meter for frequency above 1GHz above the ground. 3. The EUT was set 3 meters from the receiving antenna, which was mounted on the antenna tower. 4. The table was rotated 360 degrees to determine the position of the highest spurious emission. 5. The height of the receiving antenna is varied between one meter and four meters to search for the maximum spurious emission for both horizontal and vertical polarizations. 6. Make the measurement with the spectrum analyzer's RBW = 1MHz, VBW = 3MHz, taking record of maximum spurious emission. 7. A horn antenna was substituted in place of the EUT and was driven by a signal generator. 8. Tune the output power of signal generator to the same emission level with EUT maximum spurious emission. 9. Taking the record of output power at antenna port. 10. Repeat step 7 to step 8 for another polarization. 11. EIRP (dBm) = S.G. Power – Tx Cable Loss + Tx Antenna Gain 12. ERP (dBm) = EIRP - 2.15 13. The RF fundamental frequency should be excluded against the limit line in the operating frequency band. 14. The limit line is derived from 43 + 10log(P) dB below the transmitter power P(Watts) Sporton International (Kunshan) Inc. Page Number : 19 of 21 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E Report Template No.: BU5-FG22 Version 2.0

RF Test Report Report No. : FG950911A 5 List of Measuring Equipment Calibration Instrument Manufacturer Model No. Serial No. Characteristics Test Date Due Date Remark Date Spectrum Conducted R&S FSV30 101338 10Hz~30GHz Apr. 19, 2018 Nov. 17, 2018 Apr. 18, 2019 Analyzer (TH01-KS) Thermal Conducted Ten Billion TTC-B3S TBN-960502 -40~+150°C Apr. 19, 2018 Nov. 17, 2018 Apr. 18, 2019 Chamber (TH01-KS) EXA Spectrum Radiation Keysight N9010B MY57471084 10Hz-44GHz Jun. 25, 2018 Nov. 17, 2018 Jun. 24, 2019 Analyzer (03CH06-KS) Radiation Bilog Antenna TeseQ CBL6111D 44483 30MHz-1GHz Jan. 29, 2018 Nov. 23, 2018 Jan. 28, 2019 (03CH06-KS) Double Ridge Radiation ETS-Lindgren 3117 75957 1GHz~18GHz Oct. 20, 2018 Nov. 23, 2018 Oct. 19, 2019 Horn Antenna (03CH06-KS) Radiation SHF-EHF Horn Schwarzbeck BBHA 9170 BBHA170249 15GHz~40GHz Feb. 07, 2018 Nov. 23, 2018 Feb. 06, 2019 (03CH06-KS) Radiation Amplifier SONOMA 310N 187289 9KHz ~1GHZ Aug. 06, 2018 Nov. 23, 2018 Aug. 05, 2019 (03CH06-KS) high gain AMF-7D-00 Radiation MITEQ 2025788 1Ghz-18Ghz Apr. 17, 2018 Nov. 23, 2018 Apr. 16, 2019 Amplifier 101800-30-1 (03CH06-KS) 0P Radiation Amplifier Keysight 83017A MY53270203 500MHz~26.5GHz Dec. 16, 2017 Nov. 23, 2018 Dec. 15, 2018 (03CH06-KS) TTA1840-35 Radiation Amplifier MITEQ 2014749 18~40GHz Feb. 08, 2018 Nov. 23, 2018 Feb. 07, 2019 -HG (03CH06-KS) AC Power Radiation Chroma 61601 F104090004 N/A NCR Nov. 23, 2018 NCR Source (03CH06-KS) Radiation Turn Table ChamPro EM 1000-T 060762-T 0~360 degree NCR Nov. 23, 2018 NCR (03CH06-KS) NCR: No Calibration Required Sporton International (Kunshan) Inc. Page Number : 20 of 21 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E Report Template No.: BU5-FG22 Version 2.0

RF Test Report Report No. : FG950911A 6 Uncertainty of Evaluation Uncertainty of Radiated Emission Measurement (30 MHz ~ 1000 MHz) Measuring Uncertainty for a Level of 2.5dB Confidence of 95% (U = 2Uc(y)) Uncertainty of Radiated Emission Measurement (1 GHz ~ 18 GHz) Measuring Uncertainty for a Level of 2.0dB Confidence of 95% (U = 2Uc(y)) Uncertainty of Radiated Emission Measurement (18 GHz ~ 40 GHz) Measuring Uncertainty for a Level of 2.0dB Confidence of 95% (U = 2Uc(y)) Sporton International (Kunshan) Inc. Page Number : 21 of 21 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E Report Template No.: BU5-FG22 Version 2.0

RF Test Report Report No. : FG950911A Appendix A. Test Results of Conducted Test Conducted Output Power(Average power) Conducted Power (*Unit: dBm) Band WCDMA Band V Channel 4132 4182 4233 Frequency 826.4 836.4 846.6 AMR 12.2K 23.46 23.71 23.70 RMC 12.2K 23.48 23.72 23.71 HSDPA Subtest-1 22.63 22.77 22.73 HSDPA Subtest-2 22.13 22.23 22.19 HSDPA Subtest-3 22.17 22.31 22.27 HSDPA Subtest-4 22.09 22.22 22.16 HSUPA Subtest-1 22.42 22.98 22.56 HSUPA Subtest-2 21.10 21.21 21.13 HSUPA Subtest-3 21.94 21.86 21.70 HSUPA Subtest-4 21.50 21.63 21.69 HSUPA Subtest-5 22.80 22.60 22.70 Sporton International (Kunshan) Inc. Page Number : A1 of A11 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E

RF Test Report Report No. : FG950911A ERP WCDMA Band V (GT - LC = 2.0 dBi) 4132 4182 4233 Channel (Low) (Mid) (High) Frequency 826.4 836.4 846.6 (MHz) Conducted Power (dBm) 23.48 23.72 23.71 Conducted Power (Watts) 0.2228 0.2355 0.2350 ERP(dBm) 23.33 23.57 23.56 ERP(Watts) 0.2153 0.2257 0.2270 Sporton International (Kunshan) Inc. Page Number : A2 of A11 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E

RF Test Report Report No. : FG950911A Peak-to-Average Ratio Mode WCDMA Band V(dB) Limit: 13dB Mod. RMC 12.2Kbps Result Lowest CH 3.71 Middle CH 3.88 PASS Highest CH 4.49 Sporton International (Kunshan) Inc. Page Number : A3 of A11 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E

RF Test Report Report No. : FG950911A WCDMA Band V (RMC 12.2Kbps) Lowest Channel Middle Channel Highest Channel Sporton International (Kunshan) Inc. Page Number : A4 of A11 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E

RF Test Report Report No. : FG950911A 26dB Bandwidth Mode WCDMA Band V(MHz) Mod. RMC 12.2Kbps Lowest CH 4.718 Middle CH 4.718 Highest CH 4.703 Sporton International (Kunshan) Inc. Page Number : A5 of A11 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E

RF Test Report Report No. : FG950911A WCDMA Band V (RMC 12.2Kbps) Lowest Channel Middle Channel Highest Channel Sporton International (Kunshan) Inc. Page Number : A6 of A11 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E

RF Test Report Report No. : FG950911A Occupied Bandwidth Mode WCDMA Band V(MHz) Mod. RMC 12.2Kbps Lowest CH 4.11 Middle CH 4.12 Highest CH 4.14 Sporton International (Kunshan) Inc. Page Number : A7 of A11 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E

RF Test Report Report No. : FG950911A WCDMA Band V (RMC 12.2Kbps) Lowest Channel Middle Channel Highest Channel Sporton International (Kunshan) Inc. Page Number : A8 of A11 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E

RF Test Report Report No. : FG950911A Conducted Band Edge WCDMA Band V (RMC 12.2Kbps) Lowest Band Edge Highest Band Edge Sporton International (Kunshan) Inc. Page Number : A9 of A11 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E

RF Test Report Report No. : FG950911A Conducted Spurious Emission WCDMA Band V (RMC 12.2Kbps) Lowest Channel Middle Channel Highest Channel Sporton International (Kunshan) Inc. Page Number : A10 of A11 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E

RF Test Report Report No. : FG950911A Frequency Stability WCDMA Band V Limit Test Conditions Middle Channel (RMC 12.2KbpsRMC 12.2Kbps) 2.5ppm Temperature (°C) Voltage (Volt) Deviation (ppm) Result 50 Normal Voltage 0.0359 40 Normal Voltage 0.0024 30 Normal Voltage 0.0143 20(Ref.) Normal Voltage 0.0000 10 Normal Voltage 0.0335 0 Normal Voltage 0.0251 PASS -10 Normal Voltage 0.0060 -20 Normal Voltage 0.0275 -30 Normal Voltage 0.0311 20 Maximum Voltage 0.0048 20 Normal Voltage 0.0418 Note: 1. Normal Voltage = 3.8V. ；Battery End Point (BEP) =3.3V.；Maximum Voltage =4.3V 2. The frequency fundamental emissions stay within the authorized frequency block based on the Sporton International (Kunshan) Inc. Page Number : A11 of A11 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E

RF Test Report Report No. : FG950911A Appendix B. Test Results of Conducted Test Radiated Spurious Emission WCDMA Band V(RMC 12.2Kbps) Over S.G. TX Cable TX Antenna Frequency ERP Limit Polarization Channel Limit Power loss Gain ( MHz ) ( dBm ) ( dBm ) (H/V) ( dB ) ( dBm ) ( dB ) (dBi) 1672 -61.94 -13 -48.94 -63.15 2.32 5.68 H 2510 -67.95 -13 -54.95 -68.58 3.02 5.80 H 3345 -66.05 -13 -53.05 -68.51 3.27 7.88 H Middle 1672 -62.99 -13 -49.99 -64.20 2.32 5.68 V 2510 -68.13 -13 -55.13 -68.76 3.02 5.80 V 3345 -66.47 -13 -53.47 -68.93 3.27 7.88 V Remark: Spurious emissions within 30-1000MHz were found more than 20dB below limit line. Sporton International (Kunshan) Inc. Page Number : B1 of B1 TEL : +86-512-57900158 Report Issued Date : Jul. 11, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : XMR201907AG35E


Document Created: 2019-07-16 16:34:43
Document Modified: 2019-07-16 16:34:43
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC