Modular Approval Request

FCC ID: XMR201903EG91NS

Cover Letter(s)

Download: PDF
FCCID_4216528

Quecctel Wireless Solu utions Co ompany Limited Decla aration of the Modular Approv val Applicant / Gra antee Quectel Wireless Soluttions Compa any Limited FCC ID: I XMR2019033EG91NS Mode el: EG91‐NS The single s mod dule trans smitter has s been eva aluated th hen tested meeting the t requirements u under Partt 15C Secttion 212 as below: Mo odular app proval req quirement EUT Condition C Coom p ply (a) The radio elements e of tthe modular transmitter must m have The radio elements e of tthe modular ES YE their own shielding. The T al crystal and tuning physica transmitter have h their owwn shielding.. capacitors may m be loca ated externall to the shielded radio elements. (b) The modular transmitte er must have The modula ar has buffereed data inputs, it is YE ES buffered modulation/da m ata inputs (if such in nputs are integrated in n chip. Pleasse see provided) to o ensure that the module e will complyy with part schematic.ppdf ments under conditions of excessive data rates 15 requirem or over-moddulation. (c)Th he modular transmitter t m must have its All power lin nes derived ffrom the hostt YE ES ownn power supp ply regulation n. device are regulated r beffore energiziing other circuitts internal to the EG91-NS. Please see schematic.p pdf (d) The modular transmitterr must comply A permanen ntly attached antenna or unique YE ES with the ante enna and tra ansmission system requirrements of antenna con nnector is no ot a requirem ment for S Sections 15..203, 15.204 4(b) and 15 5.204(c). Thee antenna licensed mo odules. m must either be b permanen ntly attachedd or employ a “unique” a antenna couupler (at all connections between th he module a and the ante enna, includ ding the cab ble). The “prrofessional installation” provision p of Section S 15.2203 is not applicable to m modules but can apply to o limited mo odular approvvals under p paragraph (b b) of this secttion. (e)The moduular transsmitter m must be tested The EG91-N NSwas tested in a stand‐ YE ES i a stand-alone configurration, i.e., th in he module must m not be alone config guration via a PCMCIA innside anothe er device during testing g for compliiance with extender. Please see sp purious set‐up p 15 requirements. Un part nless the tran nsmitter moddule will be b battery powered, it must comply c with the AC line conducted c re equirementss found in S Section 15.207. AC or DC D power liines and datta input/outp put lines connnected to thhe module m must not con ntain ferrites, unless theyy will be marrketed with thhe module (see Section n 15.27(a)). The length h of these 7th Floor, Hongye Building, No.1 1801 Hongmei Roa ad, Xuhui District, Shanghai S 200233, C ChinaEmail: info@q quectel.comWebsite e: www.quectel.com mpage 1

Quecctel Wireless Solu utions Co ompany Limited liines shall be the lengthh typical of actual use or, if that leength is unkknown, at le east 10 centtimeters to innsure that thhere is no coupling c betw ween the caase of the module and s supporting e equipment. A Any accessories, peripherals, or s support equip pment conne ected to the module duriing testing s shall be unnmodified and commerrcially availa able (see S Section 1 15.31(i))must tnotbeinsidea anotherdevicceduringtesting. (f)Th he mo odular transmitter must be The label po osition of EGG91-NS is cle early YE ES equipped with w either a p permanently affixed label or must indicated. Iff the FCC ID of the modu ule be capable e of electtronically displaying d itts FCC identification n number. cannot be seen s when it is installed, then t the host lab bel must inclu ude the text: Contains FC CC ID: XMR2 201903EG91 1NS. Please see the label.pdff (g) The modula ar transmitterr must comply The EG91-N NS is complia ant with all ES YE with any specific rules or o operating requirements r s that applicable FCC F rules. D Detail instructtions pply to a com ordinarily ap mplete transm mitter and the e are given in the User Ma anual. manufacture er must proviide adequate e instructions s along with the mod dule to expla ain any suchrrequirements s. A copy of these insttructions mus ed in the application for st be include equipmentauthorizationrrequirements s,whichareba asedonthei ntendeduse//configuratio ons. (h)The modular transmitter t m must comply The EG91-N NS is approvved to comply y with YE ES w any appllicable RF exxposure requ with uirements in its final the applicabble RF expossure requirem ment, c configuration. please see the MPE eva aluation with 20cm as the distance restrictio on. Dated 2019/33/7 By: Johnny Xiang Sign nature Pri rinted Title: Project Manager M On beh half of : (Quectell Wirele ess Solutions Limited) Telephone: +86-2 2150086326 6-800 7th Floor, Hongye Building, No.1 1801 Hongmei Roa ad, Xuhui District, Shanghai S 200233, C ChinaEmail: info@q quectel.comWebsite e: www.quectel.com mpage 2


Document Created: 2019-03-22 13:19:48
Document Modified: 2019-03-22 13:19:48
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC