RFID Test report 13_56MHz

FCC ID: XKB-D3200CL

Test Report

Download: PDF

FCCID_3202954

Test report no.: 1-2054/16-01-02-B

1 Table of contents

1 Table of contents ............................................................................................................................................2
2 General information .......................................................................................................................................3
2.1 Notes and disclaimer ..........................................................................................................................3
2.2 Application details ...............................................................................................................................3
3 Test standard/s and references ....................................................................................................................3
4 Test environment............................................................................................................................................5
5 Test item ..........................................................................................................................................................5
5.1 General description .............................................................................................................................5
5.2 Additional information ........................................................................................................................5
6 Test laboratories sub-contracted .................................................................................................................5
7 Description of the test setup .........................................................................................................................6
7.1 Shielded semi anechoic chamber ......................................................................................................7
7.2 Shielded fully anechoic chamber ......................................................................................................8
7.3 AC conducted ......................................................................................................................................9
7.4 Conducted measurements normal and extreme conditions.........................................................10
8 Sequence of testing .....................................................................................................................................11
8.1 Sequence of testing radiated spurious 9 kHz to 30 MHz...............................................................11
8.2 Sequence of testing radiated spurious 30 MHz to 1 GHz ..............................................................12
9 Measurement uncertainty ............................................................................................................................13
10 Summary of measurement results ..........................................................................................................14
11 Additional comments ...............................................................................................................................15
12 Measurement results ................................................................................................................................16
12.1 Occupied bandwidth......................................................................................................................16
12.2 Field strength of the fundamental ................................................................................................18
12.3 Field strength of the harmonics and spurious ...........................................................................20
12.4 Conducted limits ............................................................................................................................24
12.5 Frequency error .............................................................................................................................27
13 Observations .............................................................................................................................................29
Annex A Document history ..........................................................................................................................29
Annex B Further information........................................................................................................................29
Annex C Accreditation Certificate ...............................................................................................................30

Page 2 of 30

Test report no.: 1-2054/16-01-02-B

Guidance Version Description

ANSI C63.4-2014 -/- American national standard for methods of measurement of radio-
noise emissions from low-voltage electrical and electronic
equipment in the range of 9 kHz to 40 GHz
ANSI C63.10-2013 -/- American national standard of procedures for compliance testing
of unlicensed wireless devices

Page 4 of 30

Test report no.: 1-2054/16-01-02-B

4 Test environment

Tnom +20 °C during room temperature tests
Temperature : Tmax +50 °C during high temperature tests
Tmin -30 °C during low temperature tests
Relative humidity content : 55 %
Barometric pressure : not relevant for this kind of testing
Vnom 110 V AC by mains adapter PSM24W-080L6
Power supply : Vmax 126.5 V
Vmin 93.5 V

5 Test item

5.1 General description

Kind of test item : Payment terminal
Type identification : DESK/3200-OP CL/ETH/MOD
HMN : -/-
PMN : DESK/3200
HVIN : DESK/3200 CL/Eth/Mod
FVIN : based on SDK 11.8
Conducted unit: No sample available!
S/N serial number :
Radiated unit: 150377313001008701001893
HW hardware status : DES32BA
SW software status : SDK 11.8
Frequency : 13.56 MHz
Type of radio transmission :
Modulated carrier
Use of frequency spectrum :
Type of modulation : ASK
Number of channels : 1
Antenna : Integrated loop antenna
Power supply : 110 V AC by mains adapter PSM24W-080L6
Temperature range : 0°C to +40°C

5.2 Additional information
The content of the following annexes is defined in the QA. It may be that not all of the listed annexes are
necessary for this report, thus some values in between may be missing.

Test setup- and EUT-photos are included in test report: 1-2054/16-01-08_AnnexA
1-2054/16-01-08_AnnexB
1-2054/16-01-08_AnnexD

6 Test laboratories sub-contracted
None

Page 5 of 30

Test report no.: 1-2054/16-01-02-B

7 Description of the test setup
Typically, the calibrations of the test apparatus are commissioned to and performed by an accredited calibration
laboratory. The calibration intervals are determined in accordance with the DIN EN ISO/IEC 17025. In addition to
the external calibrations, the laboratory executes comparison measurements with other calibrated test systems
or effective verifications. Weekly chamber inspections and range calibrations are performed. Where possible, RF
generating and signaling equipment as well as measuring receivers and analyzers are connected to an external
high-precision 10 MHz reference (GPS-based or rubidium frequency standard).

In order to simplify the identification of the equipment used at some special tests, some items of test equipment
and ancillaries can be provided with an identifier or number in the equipment list below (Lab/Item).

Agenda: Kind of Calibration

k calibration / calibrated EK limited calibration
ne not required (k, ev, izw, zw not required) zw cyclical maintenance (external cyclical
maintenance)
ev periodic self verification izw internal cyclical maintenance
Ve long-term stability recognized g blocked for accredited testing
vlkI! Attention: extended calibration interval
NK! Attention: not calibrated *) next calibration ordered / currently in progress

Page 6 of 30

Test report no.: 1-2054/16-01-02-B

8 Sequence of testing

8.1 Sequence of testing radiated spurious 9 kHz to 30 MHz
Setup
 The equipment is set up to simulate normal operation mode as described in the user manual or defined
by the manufacturer.
 If the EUT is a tabletop system, a 2-axis positioner with 1.5 m height is used.
 If the EUT is a floor standing device, it is placed directly on the turn table.
 Auxiliary equipment and cables are positioned to simulate normal operation conditions as described in
ANSI C 63.4.
 The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
 Measurement distance is 3 m (see ANSI C 63.4) – see test details.
 EUT is set into operation.

Premeasurement
 The turntable rotates from 0° to 315° using 45° steps.
 The antenna height is 1.5 m.
 At each turntable position the analyzer sweeps with positive-peak detector to find the maximum of all
emissions.

Final measurement
 Identified emissions during the premeasurement are maximized by the software by rotating the turntable
from 0° to 360°. In case of the 2-axis positioner is used the elevation axis is also rotated from 0° to 360°.
 The final measurement is done in the position (turntable and elevation) causing the highest emissions
with quasi-peak (as described in ANSI C 63.4).
 Final levels, frequency, measuring time, bandwidth, turntable position, correction factor, margin to the
limit and limit will be recorded. A plot with the graph of the premeasurement and the limit is stored.

Page 11 of 30

Test report no.: 1-2054/16-01-02-B

8.2 Sequence of testing radiated spurious 30 MHz to 1 GHz
Setup
 The equipment is set up to simulate normal operation mode as described in the user manual or defined
by the manufacturer.
 If the EUT is a tabletop system, a table with 0.8 m height is used, which is placed on the ground plane.
 If the EUT is a floor standing device, it is placed on the ground plane with insulation between both.
 Auxiliary equipment and cables are positioned to simulate normal operation conditions as described in
ANSI C 63.4.
 The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
 Measurement distance is 10 m or 3 m (see ANSI C 63.4) – see test details.
 EUT is set into operation.

Premeasurement
 The turntable rotates from 0° to 315° using 45° steps.
 The antenna is polarized vertical and horizontal.
 The antenna height changes from 1 m to 3 m.
 At each turntable position, antenna polarization and height the analyzer sweeps three times in peak to
find the maximum of all emissions.

Final measurement
 The final measurement is performed for at least six highest peaks according to the requirements of the
ANSI C63.4.
 Based on antenna and turntable positions at which the peak values are measured the software maximize
the peaks by changing turntable position ± 45° and antenna height between 1 and 4 m.
 The final measurement is done with quasi-peak detector (as described in ANSI C 63.4).
 Final levels, frequency, measuring time, bandwidth, antenna height, antenna polarization, turntable angle,
correction factor, margin to the limit and limit are recorded. A plot with the graph of the premeasurement
with marked maximum final results and the limit is stored.

Page 12 of 30

Test report no.: 1-2054/16-01-02-B

9 Measurement uncertainty

Measurement uncertainty
Test case Uncertainty
Occupied bandwidth ± used RBW
Field strength of the fundamental ± 3 dB
Field strength of the harmonics and spurious ± 3 dB
Receiver spurious emissions and cabinet radiations ± 3 dB
Conducted limits ± 2.6 dB

Page 13 of 30

Test report no.: 1-2054/16-01-02-B

11 Additional comments
Reference documents: newCustomer Questionnaire D3200 FCC

Special test descriptions: None

Configuration descriptions: None

Test mode: ☐ No test mode available.

☒ Special software is used.
EUT is transmitting pseudo random data by itself

Antennas and transmit ☒ Operating mode 1 (single antenna)
operating modes: - Equipment with 1 antenna,
- Equipment with 2 diversity antennas operating in switched diversity mode
by which at any moment in time only 1 antenna is used,
- Smart antenna system with 2 or more transmit/receive chains, but
operating in a mode where only 1 transmit/receive chain is used)

☐ Operating mode 2 (multiple antennas, no beamforming)
- Equipment operating in this mode contains a smart antenna system using two or more
transmit/receive chains simultaneously but without beamforming.

☐ Operating mode 3 (multiple antennas, with beamforming)
- Equipment operating in this mode contains a smart antenna system using two or more
transmit/receive chains simultaneously with beamforming.
In addition to the antenna assembly gain (G), the beamforming gain (Y) may have to be taken
into account when performing the measurements.

Page 15 of 30

Test report no.: 1-2054/16-01-02-B

12 Measurement results

12.1 Occupied bandwidth
Measurement:

The emission bandwidth (x dB) is defined as the frequency range between two points, one above and one
below the carrier frequency, at which the spectral density of the emission is attenuated x dB below the
maximum in-band spectral density of the modulated signal.

Measurement parameters
Detector: Peak
Resolution bandwidth: 1 % – 5 % of the occupied bandwidth
Video bandwidth: ≥ 3x RBW
Trace mode: Max hold
Analyzer function: 99 % power function
Used equipment: See chapter 7.4 – B
Measurement uncertainty: See chapter 9

Limit:

IC
for RSP-100 test report coversheet only

Result:

99% emission bandwidth
331 kHz

Page 16 of 30

Test report no.: 1-2054/16-01-02-B

12.2 Field strength of the fundamental
Measurement:

The maximum detected field strength for the carrier signal.

Measurement parameters
Detector: Quasi peak / peak (worst case)
Resolution bandwidth: 120 kHz
Video bandwidth: ≥ 3x RBW
Trace mode: Max hold
Used equipment: See chapter 7.2 – A
Measurement uncertainty: See chapter 9

Limit:

FCC & IC
Frequency Field strength Measurement distance
(MHz) (µV/m) (m)
13.553 to 13.567 15,848 (84 dBµV/m) 30

Recalculation:

According to ANSI C63.10
Frequency Formula Correction value
FSlimit = FSmax 40 log 20log )
nearfield

FSlimit is the calculation of field strength at the limit distance,
13.56 MHz expressed in dBµV/m
-21.39 dB
FSmax is the measured field strength, expressed in dBµV/m
dnear field is the λ/2π distance
dmeasure is the distance of the measurement point from EUT
dlimit is the reference limit distance

According to ANSI C63.10

Result:

Field strength of the fundamental
Frequency 13.56 MHz
Distance @3m @ 30 m
78.55 dBµV/m (peak) 57.16 dBµV/m (peak)
Measured / calculated value
78.09 dBµV/m (average) 56.70 dBµV/m (average)

Page 18 of 30

Test report no.: 1-2054/16-01-02-B

12.3 Field strength of the harmonics and spurious
Measurement:

The maximum detected field strength for the harmonics and spurious.

Measurement parameters
Quasi peak / average or
Detector:
peak (worst case – pre-scan)
F < 150 kHz: 200 Hz
Resolution bandwidth: 150 kHz < F < 30 MHz: 9 kHz
30 MHz < F < 1 GHz: 120 kHz
F < 150 kHz: 1 kHz
Video bandwidth: 150 kHz < F < 30 MHz: 100 kHz
30 MHz < F < 1 GHz: 300 kHz
Trace mode: Max hold
See chapter 7.1 – A
Used equipment: See chapter 7.2 – A
See chapter 7.4 – B
Measurement uncertainty: See chapter 9

Limit:

FCC & IC
Frequency Field strength Measurement distance
(MHz) (dBµV/m) (m)
0.009 – 0.490 2400/F(kHz) 300
0.490 – 1.705 24000/F(kHz) 30
1.705 – 30 30 (29.5 dBµV/m) 30
30 – 88 100 (40 dBµV/m) 3
88 – 216 150 (43.5 dBµV/m) 3
216 – 960 200 (46 dBµV/m) 3

Note: For a reduced measurement distance, please take a look at the limit line and the ANSI C63.10-2013
sub clause 6.4 radiated emissions from unlicensed wireless devices below 30 MHz.

Result:

Detected emissions
Frequency Resolution bandwidth
Detector Detected value
(MHz) (kHz)
All detected peak emissions are below the average limit.
For emissions 30 MHz to 1 GHz, please look at the table below the 1 GHz plot.

Page 20 of 30

Test report no.: 1-2054/16-01-02-B

Plots:

Plot 1: 9 kHz – 30 MHz, magnetic emissions
130
dBµV/m
120

110

100

90

80

70

60

50

40

30

20

10
9kHz 100k 1M 10M 30MHz
Frequency

Page 21 of 30

Test report no.: 1-2054/16-01-02-B

Plot 3: 30 MHz – 1 GHz, vertical and horizontal polarization

60

55

50

45 FCC_10m_B

40
Level in dBµV/m

35

30

25

20

15

10

5

0
30M 50 60 80 100M 200 300 400 500 800 1,05G
Frequency in Hz

Final_Result:

Meas.
Frequency QuasiPeak Limit Margin Bandwidth Height Azimuth Corr.
Time Pol
(MHz) (dBµV/m) (dBµV/m) (dB) (kHz) (cm) (deg) (dB)
(ms)
40.669350 20.80 30.00 9.20 1000.0 120.000 103.0 V 163.0 14.0
65.322450 15.01 30.00 14.99 1000.0 120.000 273.0 V 118.0 9.4
68.695950 5.35 30.00 24.65 1000.0 120.000 200.0 H 40.0 8.7
135.594300 24.44 33.50 9.06 1000.0 120.000 100.0 V 265.0 9.0
216.957450 20.95 36.00 15.05 1000.0 120.000 101.0 V 7.0 12.3
225.001500 24.38 36.00 11.62 1000.0 120.000 103.0 V 32.0 12.6

Page 23 of 30

Test report no.: 1-2054/16-01-02-B

12.4 Conducted limits
Measurement:

Measurement of the conducted spurious emissions for an intentional radiator that is designed to be connected
to the public utility (AC) power line.

Measurement parameters
Quasi peak / average or
Detector:
peak (worst case – pre-scan)
F < 150 kHz: 200 Hz
Resolution bandwidth:
F > 150 kHz: 9 kHz
F < 150 kHz: 1 kHz
Video bandwidth:
F > 150 kHz: 100 kHz
Trace mode: Max hold
Used equipment: See chapter 7.3 – A
Measurement uncertainty: See chapter 9

Limit:

FCC & IC
Frequency Quasi-peak Average
(MHz) (dBµV/m) (dBµV/m)
0.15 – 0.5 66 to 56* 56 to 46*
0.5 – 5 56 46
5 – 30.0 60 50

Result:

Detected emissions
Frequency Resolution bandwidth
Detector Detected value
(MHz) (kHz)
See table below the plots.

Page 24 of 30

Test report no.: 1-2054/16-01-02-B

Plots:

Plot 1: 150 kHz to 30 MHz, phase line

Premeasurement
Average limit class B
Quasi peak limit class B
Measurement Average level
Quasi peak level

Phase line

80.0

70.0

60.0

50.0
Amplitude in dBµV

40.0

30.0

20.0

10.0

0
150.0K 1.0M 10.0M 30.0M

Frequency in Hz

Project ID: 1-2054/16-01-02

Quasi peak Margin Average Margin
Frequency Limit QP Limit AV
level quasi peak level average
MHz dBµV dB dBµV dBµV dB dBµV

0.155112 59.41 6.31 65.722 35.28 20.58 55.854
0.189269 55.30 8.77 64.069 33.68 21.20 54.878
0.356611 45.96 12.85 58.807 32.42 17.68 50.097
0.418971 38.56 18.91 57.469 25.14 23.17 48.315
2.926505 34.50 21.50 56.000 24.49 21.51 46.000
4.847480 34.47 21.53 56.000 25.21 20.79 46.000
4.930747 34.47 21.53 56.000 25.41 20.59 46.000
5.020108 35.25 24.75 60.000 24.89 25.11 50.000
7.047709 36.59 23.41 60.000 27.48 22.52 50.000
7.948510 36.86 23.14 60.000 27.22 22.78 50.000
13.559843 44.20 15.80 60.000 41.75 8.25 50.000
27.119749 41.26 18.74 60.000 39.67 10.33 50.000

Page 25 of 30

Test report no.: 1-2054/16-01-02-B

Plot 2: 150 kHz to 30 MHz, neutral line

Premeasurement
Average limit class B
Quasi peak limit class B
Measurement Average level
Quasi peak level

Neutral line

80.0

70.0

60.0

50.0
Amplitude in dBµV

40.0

30.0

20.0

10.0

0
150.0K 1.0M 10.0M 30.0M

Frequency in Hz

Project ID: 1-2054/16-01-02

Quasi peak Margin Average Margin
Frequency Limit QP Limit AV
level quasi peak level average
MHz dBµV dB dBµV dBµV dB dBµV

0.161767 58.91 6.46 65.373 35.88 19.78 55.664
0.266878 46.90 14.31 61.215 28.01 24.65 52.661
0.306555 45.58 14.48 60.063 30.36 21.17 51.527
0.356350 45.23 13.59 58.813 32.70 17.40 50.104
4.846473 34.67 21.33 56.000 25.25 20.75 46.000
4.915902 34.64 21.36 56.000 25.61 20.39 46.000
4.916978 34.68 21.32 56.000 25.61 20.39 46.000
4.983803 34.68 21.32 56.000 25.32 20.68 46.000
7.289049 36.49 23.51 60.000 27.68 22.32 50.000
7.597589 36.27 23.73 60.000 27.34 22.66 50.000
13.560523 43.64 16.36 60.000 41.13 8.87 50.000
27.120285 41.25 18.75 60.000 39.62 10.38 50.000

Page 26 of 30

Test report no.: 1-2054/16-01-02-B

12.5 Frequency error
Measurement:

The maximum detected field strength for the spurious.

Measurement parameters
Detector: Peak detector
Resolution bandwidth: 100 Hz
Video bandwidth: > RBW
Trace mode: Max hold
Used equipment: See chapter 7.4 – A
Measurement uncertainty: See chapter 9

Limit:

FCC
The frequency tolerance of the carrier signal shall be maintained within +/- 0.01% of the operating
frequency over a temperature variation of -20 degrees to +50 degrees C at normal supply voltage,
and for a variation in the primary supply voltage from 85% to 115% of the rated supply voltage at a
temperature of 20 degrees C. (±1.356 kHz)

Result: Temperature variation

Frequency tolerance
Measured frequency
Conditions Result
(MHz)
13.55963 -20 °C & 100% voltage compliant
13.55962 -10 °C & 100% voltage compliant
13.55960 0 °C & 100% voltage compliant
13.55958 +10 °C & 100% voltage compliant
13.55959 +20 °C & 100% voltage compliant
13.55955 +30 °C & 100% voltage compliant
13.55956 +40 °C & 100% voltage compliant
13.55961 +50 °C & 100% voltage compliant

Result: Voltage variation

Frequency tolerance
Measured frequency
Temperature Result
(MHz)
13.55960 +20 °C & 85% voltage compliant
13.55959 +20 °C & 100% voltage compliant
13.55959 +20 °C & 115% voltage compliant

Page 27 of 30

Test report no.: 1-2054/16-01-02-B

13 Observations
No observations except those reported with the single test cases have been made.

Annex A Document history

Version Applied changes Date of release

Initial release 2016-08-16

A Changed FCC ID 2016-08-26

B Changed HVIN & FVIN 2016-11-07

Annex B Further information
Glossary

AVG - Average
DUT - Device under test
EMC - Electromagnetic Compatibility
EN - European Standard
EUT - Equipment under test
ETSI - European Telecommunications Standard Institute
FCC - Federal Communication Commission
FCC ID - Company Identifier at FCC
HW - Hardware
IC - Industry Canada
Inv. No. - Inventory number
N/A - Not applicable
PP - Positive peak
QP - Quasi peak
S/N - Serial number
SW - Software
PMN - Product marketing name
HMN - Host marketing name
HVIN - Hardware version identification number
FVIN - Firmware version identification number

Page 29 of 30

Document Created: 2016-11-07 10:09:46
Document Modified: 2016-11-07 10:09:46

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC