User manual - XKB-AXIPRTBT.pdf

FCC ID: XKB-AXIPRTBT

Users Manual

Download: PDF
FCCID_4160866

AXIUM PRINTER
User Guide


    Contents

1_Introduction                                                           4

2_Presentation                                                           5

         2_1 Content of the box                                           5
                2_1_1 Printer                                             5

         2_2 Overview on the Axium Printer                                6

3_Use of the terminal                                                    7

         3_1 Switching off the terminal                                   7

         3_2 Advance paper                                                8

         3_3 Meaning leds                                                 8


4_Installation                                                           9

         4_1 Recommendations                                              9

         4_2 USB Printer connections                                     10
                4_2_1 USB                                                10


         4_3 Opening trap door                                           10

         4_4 Battery                                                     11
                4_4_1 Main characteristics                               11

                4_4_2 Installing the battery                             11

                4_4_3 Charging the battery                               11

                4_4_4 Changing the battery                               12




                                                  Copyright© 2019 Ingenico
                                                          All rights reserved
AXIUM PRINTER                       2
                                               900035197 R11 000 03/0119


         4_5 Paper roll                                                 14
                4_5_1 Main characteristics of INGENICO                  14

		paper roll

                4_5_2 Installing paper roll                             15

         4_6 Installing Belt Attach                                     16


5_Recommendations                                                      17
         5_1 Safety                                                     17

6_Standards                                                            19

7_FCC/IC Compliance                                                    20
         7_1 Federal Communications
         Commission (FCC) Statement                                     20

         7_2 Industry Canada (IC) Statement                             21

8_Troubleshooting                                                      21




                                                 Copyright© 2019 Ingenico
                                                         All rights reserved
AXIUM PRINTER                        3
                                              900035197 R11 000 03/0119


1_Introduction
We hope that you will be fully satisfied with your new terminal Axium
Printer. Please select by yourself in this documentation items related
to your model.

Read this guide to understand and make the best use of your terminal.
It presents you the necessary information about use, installation,
maintenance, safety and security recommendations.




          WARRANTY / SECURITY
          Use only the power supply included with the product to
          ensure best performance and safety. Maintenance should
          only be provided by Ingenico authorized technician.
          Failure to comply with these instructions will void the
          manufacturer’s responsibility.




          This symbol indicates an important Warning.




          This symbol indicates a piece of advice.




                                                Copyright© 2019 Ingenico
                                                        All rights reserved
AXIUM PRINTER                       4
                                             900035197 R11 000 03/0119


2_Presentation
     2_1 Content of the box
         2_1_1 Printer

  Axium Printer terminal unit with paper roll


                                                Paper roll




                                            Power adapter

   A battery pack disconnected




                                                   User guide
                         Belt attach



       Pin




         ADVICE
         Keep the packaging. It must be re-used whenever the termi-
         nal is shipped.


                                                  Copyright© 2019 Ingenico
                                                          All rights reserved
AXIUM PRINTER                      5
                                            900035197 R11 000 03/0119


      2_2 Overview of the Axium Printer
     Terminal unit


                   Easy loading
                   printer


Bluetooth
indication led                                                    Power Led




Advance
paper key


                                                        ON key
NFC pairing
area

                 Charging USB type C connector


     Compartment where are located:

              the battery pack




                                                    Copyright© 2019 Ingenico
                                                            All rights reserved
AXIUM PRINTER                        6
                                                 900035197 R11 000 03/0119


 Weight
                                         167g
 (without paper roll with battery)

 Dimensions (L x w x h)                  102x84x46 mm

                                         100-240VAC / 50-60 Hz -
 Electrical mains network
                                         Class VI equipment

 Connections on terminal                 Type C USB Power connector




3_Use of the Axium Printer

          ADVICE
          Before to use the terminal, always check if the roll of paper
          is present.


     3_1 Switching off the Axium Printer
     If the battery is empty completelly, the terminal automatically
     shuts off.
     It may also be switched off by pressing “ON key” during one
     second until the power led switch off.




                                                                   ON key




     In order to restart the terminal, press « ON key ».




                                                   Copyright© 2019 Ingenico
                                                           All rights reserved
AXIUM PRINTER                        7
                                                900035197 R11 000 03/0119


       3_2 Advance paper
       Advance the paper by pressing “advance paper key”.




Advance paper key




       3_3 Meaning leds

Bluetooth led : blue when
the printer is connected
by Bluetooth interface




               Power led                                      Meaning

   Green (flashing during battery charge)        Battery level between 50% - 100%

   Yellow (flashing during battery charge)       Battery level between 30% - 50%

   orange (flashing during battery charge)       Battery level between 0% - 30%

   Red (flashing during battery charge)          Battery empty cannot printing

   Blue flashing                                 No battery

   Quick red flashing                            No paper detected




                                                              Copyright© 2019 Ingenico
                                                                      All rights reserved
AXIUM PRINTER                                8
                                                        900035197 R11 000 03/0119


4_Installation
      4_1 Recommendations

Location of the Axium printer
The printer should be placed far from any very hot zones, protected
from vibrations, dust, damp and electromagnetic radiation (computer
screen, anti-theft barrier etc.).

Operating conditions


  Ambient temperature          from -10°C to +45°C

  Max relative humidity        85% at +40°C



Battery charging conditions


  Ambient temperature          from +0°C to +40°C


Storage conditions


  Ambient temperature          from -20°C to +55°C

  Max relative humidity        85% at +55°C




                                              Copyright© 2019 Ingenico
                                                      All rights reserved
AXIUM PRINTER                     9
                                           900035197 R11 000 03/0119


     4_2 USB Printer connections
        4_2_1 USB
          There is an USB connector (USB type C) on the left side
          of the Axium printer terminal (see below picture). This
          connector manages the battery charge.




                      USB type C
                      Connector used for PC travel charger, etc...



     4_3 Opening trap door

        CAUTION
        Switch off the terminal before opening the trapdoor.

          Flip the printer and unclip the trapdoor by pushing on the
          clip with as shown with the arrows on the picture.




                                                    Copyright© 2019 Ingenico
                                                            All rights reserved
AXIUM PRINTER                      10
                                               900035197 R11 000 03/0119


      4_4 Battery
          4_4_1 Main characteristics

Characteristics              Li-ion 2250 mAh

Charge (power supply-1.0A)   50% capacity in 1:15; full capacity in
                             2:30


          4_4_2 Installing the battery

          WARNING
          Check that the terminal is not connected to the main electric
          network.


        Flip your printer and unclip the battery trapdoor by pushing
        on the button as shown on the picture
        Disengage the trapdoor
        Take the battery pack included in the box
        Locate the battery pack connector beside the battery
        compartment
        Plug the battery pack connector according to the connector
        locating system and (as shown on picture).
        Verify that it locks.
        Place the battery pack in its compartment.
        Close the battery compartment trapdoor.




                                                Copyright© 2019 Ingenico
                                                        All rights reserved
AXIUM PRINTER                      11
                                             900035197 R11 000 03/0119


        4_4_3 Charging the battery


        When does the battery need to be charged?

                On initial start-up, charge the battery for 4 hours
                under the environmental conditions stated above

                When used with a terminal power supply: connect the
                power supply to Axium printer power connector.


        How does the battery need to be charged?
                For the power state of the printer, please refer to § 3.3

                The environment in which the charge takes place
                influences battery lifetime and autonomy (number of
                ticket printing)
                The optimal conditions are as follows:
                    - Charging away from any external heat source
                (radiator, sun, enclosed area…)
                     - The optimal temperature is between +15°C and
                +25°C


        How can the battery be charged?

        Using the terminal power supply
                Connect the terminal power supply unit to the terminal
                type C connector located on the left side of the
                terminal.

                Connect the power supply unit to the power supply
                mains network
                Check to see if the power led is flashing (=battery
                charging)




                                                  Copyright© 2019 Ingenico
                                                          All rights reserved
AXIUM PRINTER                       12
                                              900035197 R11 000 03/0119


        4_4_4 Changing the battery


        It is imperative to use a battery authorized by Ingenico.
        There is danger of explosion if battery used is not approved
        by Ingenico.


          Turn it off by pressing “ON key” for about one second
          Remove the battery trapdoor (see section 4.3“opening
          trap door”)
          Lift the battery and remove it from its compartment
          Carefully disconnect battery, following the instructions
          below.




          Connect and install the new battery by following the
          instructions in section 4.4.2 “Installing battery”
          Close the battery trapdoor and charge the new battery.
          See section «4.4.3 “Charging the Battery»
          In order to preserve the environment, dispose used
          battery in compliance with current country recycling
          legislation.




                                              Copyright© 2019 Ingenico
                                                      All rights reserved
AXIUM PRINTER                    13
                                          900035197 R11 000 03/0119


     4_5 Paper roll
         4_5_1 Mains characteristics of INGENICO
         paper roll


  R40 paper roll characteristics                Precisions

             Colour                               White

              Width                              58 mm

            Diameter                             42 mm

             Length                         About 18 metres


        The thermal paper can be deteriorated by poor storage
        conditions, so we recommend you to avoid:

            / storage in hot wet places (near air-conditioner, humidity
            higher than 85%)
            / exposure to sunlight or ultraviolet for long periods
            / contact with organic solvents (solvent type adhesive)
            / direct contact with materials containing plasticizers (PVC
            transparent folders or envelopes)
            / direct contact with «diazo» papers
            / direct contact with water
            / Rubbing or pressing the paper too strongly



         WARNING
         For best product performance, only use heat sensitized
         paper approved by Ingenico.



         WARNING
         Switch off the terminal prior to installing a paper roll.
         Use only paper approved by Ingenico.
         The use of non approved paper is likely to damage the
         printer of your terminal.




                                                 Copyright© 2019 Ingenico
                                                         All rights reserved
AXIUM PRINTER                      14
                                             900035197 R11 000 03/0119


        4_5_2 Installing paper roll
        Open the paper compartment by pulling on each side of the
        printer and pull the cover to the rear of the terminal.




        Insert the paper roll in the compartment following the
        directions shown on the below picture
        Pull the paper up to the top of the terminal
        Maintain the paper and close the lid
        Press simultaneously on both upper corners of the
        paperflap, as shown by arrows on picture, until it clips into
        position
        when the paper is empty, power led flash quickly in red.




                                               Copyright© 2019 Ingenico
                                                       All rights reserved
AXIUM PRINTER                    15
                                           900035197 R11 000 03/0119


      4_6 Installing Belt Attach
Disconnect the battery by following the instructions in section 4.4.4



                                                Insert the belt attach
   Remove the silicon part




   Insert the pin on the belt attach


                                                     Pull the attach belt
                                                     until you click




Install the battery by following the instructions in section 4.4.2


                                                   Copyright© 2019 Ingenico
                                                           All rights reserved
AXIUM PRINTER                          16
                                               900035197 R11 000 03/0119


5_Recommendations
      5_1 Safety
Powering down the Axium Printer :
       Disconnect the Printer power supply block adapter from the
       electrical mains network.

Battery
      Axium printer is fitted with battery specially designed for this
      terminal.
          Only use the appropriate chargers and batteries listed in the
          Ingenico’s catalogue.
          Do not short-circuit the battery.
          Do not attempt to open the battery container.
          Used batteries must be disposed of at the appropriated sites.


           WARNING
           There is a risk of explosion if the battery is incorrectly re-
           placed or is placed in a fire.


Electrical power outlet
      The electrical outlet must meet the following criteria :
          Must be installed near the equipment and easily accessible;
          Do not short-circuit the battery.
          Do not attempt to open the battery container.
          Used batteries must be disposed of at the appropriates sites.


The power supply label contains six symbols :


          Double insulation symbol



          DC current output


          AC current input




                                                   Copyright© 2019 Ingenico
                                                           All rights reserved
AXIUM PRINTER                        17
                                               900035197 R11 000 03/0119


          DC Power jack polarity



          In door user only




          International Efficiency Marking Protocol (Energy Star Level 5)




On airplanes
      Your handset must be switched off by removing the battery
      pack. Remove the battery from the terminal when on an airplane.
      Non-compliance with these safety rules may result in legal
      action and/or a ban on later access to cellular network services.

Explosion areas
      Certain regulations restrict the use of radio equipment in
      chemical plants, fuel depots and any site where blasting is
      carried out. You are urged to comply with these regulations. The
      terminal shall be protected by a specially fitted and certified
      cover enabling use in proximity to a fuel pump.

Electronic health appliances
      Your handset is a radio transmitter which may interfere with
      health appliances, such as hearing aids, pacemaker, hospital
      equipment, etc.
      Your doctor or the equipment manufacturer will be able to
      provide you with appropriate advice.




                                                         Copyright© 2019 Ingenico
                                                                 All rights reserved
AXIUM PRINTER                             18
                                                     900035197 R11 000 03/0119


6_Standards
Environment (WEEE, Batteries and
Packaging)

This product is labeled in accordance with European Directives
2002/96/EC concerning Waste Electrical and Electronic Equipment
(WEEE) and 2006/66/EC concerning Batteries and Accumulators. Those
provisions are requiring producers and manufacturers to become liable
for take-back, treatment and recycling upon end of life of equipment
and batteries.




              The associated symbol means that WEEE and waste
              batteries must not be thrown away but collected
              separately and recycled.




Ingenico ensures that efficient collection and recycling schemes are
set-up for WEEE and batteries according to the local regulation of your
country. Please contact your retailers for more detailed information
about the compliance solution in place for disposing of your old
product and used batteries.

Packaging waste must also be collected separately to assure a proper
disposal and recycling.

Please note that proper recycling of the electrical and electronic
equipment and waste batteries will ensure safety of human health and
environment.




                                                 Copyright© 2019 Ingenico
                                                         All rights reserved
AXIUM PRINTER                       19
                                             900035197 R11 000 03/0119


7_FCC/IC Compliance
        7_1 Federal Communications Commis-
        sion (FCC) Statement
This device complies with Part 15 of the FCC Rules. Operation is subject
to the condition that this device does not cause harmful interference.

15.21
CAUTION : This equipment may not be modified, altered, or changed
in any way without signed written permission from “INGENICO”.
Unauthorized modification may void the equipment authorization from
the FCC and will void the “INGENICO” warranty.

15.105(b)
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures :
         Reorient or relocate the receiving antenna.
         Increase the separation between the equipment and receiver.
         Connect the equipment into an outlet on a circuit different
         from that to which the receiver is connected.
         Consult the dealer or an experienced radio/TV technician for
         help.

15.19 (a) (3)
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
1) This device may not cause harmful interference and
2) This device must accept any interference received, including
interference that may cause undesired operation of the device.

The device complies with FCC radiation exposure limits set forth for
general population. This device must not be co-located or operating in
conjuction with any other antenna or transmitter.

                                                    Copyright© 2019 Ingenico
                                                            All rights reserved
AXIUM PRINTER                         20
                                                900035197 R11 000 03/0119


       7_2 Industry Canada (IC) Statement.
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
1) this device may not cause interference, and
2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may only
operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada.
To reduce potential radio interference to other users, the antenna
type and its gain should be so chosen that the equivalent isotropically
radiated power (e.i.r.p.) is not more than that necessary for successful
communication.

Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes:
1) l’appareil ne doit pas produire de brouillage, et
2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
Conformément à la réglementation d’Industrie Canada, le présent
émetteur radio peut fonctionner avec une antenne d’un type et d’un
gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie
Canada.
Dans le but de réduire les risques de brouillage radioélectrique à
l’ intention d’autres utilisateurs, il faut choisir le type d’antenne et
son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une
communication satisfaisante.
This device complies with ISED radiation exposure limits set forth
general population. This device must not be co-located or operating in
conjunction with any other antenna or transmitter.


8_Troubleshooting
The terminal does not turn on
         Check the battery ( is it discharged, is it connected ?)
                    A full discharged battery can take long charging
                    time to recover
         Connect terminal to terminal power supply or put it on powered
         base

                                                    Copyright© 2019 Ingenico
                                                            All rights reserved
AXIUM PRINTER                          21
                                                900035197 R11 000 03/0119


“This Document is Copyright © 2019 by INGENICO Group. INGENICO
retains full copyright ownership, rights and protection in all material
contained in this document. The recipient can receive this document
on the condition that he will keep the document confidential and will
not use its contents in any form or by any means, except as agreed
beforehand, without the prior written permission of INGENICO.
Moreover, nobody is authorized to place this document at the disposal
of any third party without the prior written permission of INGENICO.
If such permission is granted, it will be subject to the condition that
the recipient ensures that any other recipient of this document, or
information contained therein, is held responsible to INGENICO for the
confidentiality of that information.
Care has been taken to ensure that the content of this document is
as accurate as possible. INGENICO however declines any responsibility
for inaccurate, incomplete or outdated information. The contents of
this document may change from time to time without prior notice, and
do not create, specify, modify or replace any new or prior contractual
obligations agreed upon in writing between INGENICO and the user.
INGENICO is not responsible for any use of this device, which would be
non consistent with the present document.
All trademarks used in this document remain the property of their
rightful owners.”




                              Your contact




www.ingenico.com
28-32, boulevard de Grenelle, 75015 Paris - France / (T) +33 (0)1 58 01 80 00 / (F) +33 (0)1 58 01 91 35
Ingenico - SA au capital de 47 656 332 / 317 218 758 RCS Nanterre




                                                                         Copyright© 2019 Ingenico
                                                                                 All rights reserved
AXIUM PRINTER                                        21
                                                                    900035197 R11 000 03/0119



Document Created: 2019-01-28 16:21:48
Document Modified: 2019-01-28 16:21:48

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC