RF Exposure Info

FCC ID: XJTGEFIT37

RF Exposure Info

Download: PDF
FCCID_3252930

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M-10, Middle section, Science & Technology Park, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Report No.: SZEM161201097802 Fax: +86 (0) 755 2671 0594 Email: ee.shenzhen@sgs.com Page: 1 of 6 1 Cover page SAR Evaluation Report Application No.: SZEM1612010978CR Applicant: Shenzhen Gold-East Electronic Co., Ltd Manufacturer: Shenzhen Gold-East Electronic Co., Ltd Factory: Shenzhen Gold-East Electronic Co., Ltd Product Name: Smart Bracelet Model No.(EUT): GE-W37 FCC ID: XJTGEFIT37 Standards: 47 CFR Part 1.1307 (2015) 47 CFR Part 2.1093 (2015) KDB447498D01 General RF Exposure Guidance v06 Date of Receipt: 2016-12-21 Date of Test: 2016-12-22 to 2016-12-29 Date of Issue: 2016-12-30 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above. Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201097802 Page: 2 of 6 2 Version Revision Record Version Chapter Date Modifier Remark 00 2016-12-30 Original 2016-12-29 Tested By (Edison Li) /Project Engineer Date 2016-12-30 Checked By (Eric Fu) /Reviewer Date This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201097802 Page: 3 of 6 3 Contents Page 1 COVER PAGE .....................................................................................................................................................1 2 VERSION..............................................................................................................................................................2 3 CONTENTS ..........................................................................................................................................................3 4 GENERAL INFORMATION ................................................................................................................................4 4.1 CLIENT INFORMATION.........................................................................................................................................4 4.2 GENERAL DESCRIPTION OF EUT ..........................................................................................................................4 4.3 TEST LOCATION ..................................................................................................................................................5 4.4 TEST FACILITY ...................................................................................................................................................5 4.5 DEVIATION FROM STANDARDS ............................................................................................................................5 4.6 ABNORMALITIES FROM STANDARD CONDITIONS ..................................................................................................5 4.7 OTHER INFORMATION REQUESTED BY THE CUSTOMER .........................................................................................5 5 SAR EVALUATION .............................................................................................................................................6 5.1 RF E XPOSURE COMPLIANCE REQUIREMENT .........................................................................................................6 5.1.1 Standard Requirement ...........................................................................................................................6 5.1.2 Limits .......................................................................................................................................................6 5.1.3 EUT RF Exposure ..................................................................................................................................6 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201097802 Page: 4 of 6 4 General Information 4.1 Client Information Applicant: Shenzhen Gold-East Electronic Co., Ltd Address of Applicant: 6F, Bldg#11, Yusheng Industry Area, #467 Gushu, Xixiang, Bao'an District, Shenzhen, China Manufacturer: Shenzhen Gold-East Electronic Co., Ltd Address of Manufacturer: 6F, Bldg#11, Yusheng Industry Area, #467 Gushu, Xixiang, Bao'an District, Shenzhen, China Factory: Shenzhen Gold-East Electronic Co., Ltd Address of Factory: 6F, Bldg#11, Yusheng Industry Area, #467 Gushu, Xixiang, Bao'an District, Shenzhen, China 4.2 General Description of EUT Product Name: Smart Bracelet Model No.: GE-W37 Frequency Range: 2402MHz to 2480MHz Bluetooth Version: V4.0 BLE Modulation Type: GFSK Number of Channels: 40 Sample Type: Portable production Antenna Type: Integral Antenna Gain: 0dBi Battery: 3.7V 50mAh rechargeable battery which charged by AC adapter DC Cable: 22cm unshielded This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM161201097802 Page: 5 of 6 4.3 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M-10, Middle section, Science & Technology Park, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 No tests were sub-contracted. 4.4 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • CNAS (No. CNAS L2929) CNAS has accredited SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01. • VCCI The 10m Semi-anechoic chamber and Shielded Room of SGS-CSTC Standards Technical Services Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: G-823, R-4188, T-1153 and C-2383 respectively. • FCC – Registration No.: 556682 SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration No.: 556682. • Industry Canada (IC) Two 3m Semi-anechoic chambers and the 10m Semi-anechoic chamber of SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab have been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 4620C-1, 4620C-2, 4620C-3. 4.5 Deviation from Standards None. 4.6 Abnormalities from Standard Conditions None. 4.7 Other Information Requested by the Customer None. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS—CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZENM161201087802 Page Sot s 5 SAR Evaluation 5.1 RF Exposure Compliance Requirement 5.1.1 Standard Requirement According to KOB447498001 General RF Exposire Guicknce v08 4.8.1. Sandalone SARt est exclusion considertions Unless speciiealy requtied by the publshed RF axposure KDB procedures, standalone 1—g hesel or bacy and 10.q axtramty SAR avaluationor general popultion exposure conditons, by messurement or numerical smultion, is nt reaured when the corponing SAR Exclusion Thresholi conditon, ted balon,i satatled 5.1.2Limits "The 1—a and 109 SAR test oxclusion throsholds for 100 NHlz t 8 GHattest separation stances £ 50 mm are determinad by: I(max. powar of channel, inclucing tine—up tolerance, mW)Itmin. tet epration distance,mm}]° [M(GHtz] s 3.0for 1—9 SAR andls 7.5 for 10.4 xtromity SAR, where 1(GHz) is the RF channetransmt freguancy in Gile Powar and distance are rounded tothe nearest m and mm before calcultion" "The resultis roundad to one decimal place for comparison "The test exclusions are appleable only when the minimum test separaton ditanceis < 50mm and for transnmission racunciesbatween 100 MH and 6 Giz. When the minimum test separation eistance is < 5 mm, a eitence o 3 mm is appled tdetermine SAR test exclusion 5.1.3EUT RF Exposure "The Mex Gondicied Posk Octput Ponar is —36ddBm in Nighest channal(2402GHe}: —3.60dBm logarthinic tarms comertto numerie resultis nearly OdmW According tothe frmula. caleulte the test exclusion threshoids: {(max. powar of channel, nclucing tne—up tolerance, mW)#fmin. test spration distancs,mm}]° M(Gten General RF Exposure — (0A9mW /5 mm x <2402GHe — 0.18 ® SA requirement s—a0 @: ®«@ So the SAR repor is not reguired Tt iateere renncano in ont ces oounaneeseaurescoms inreamemecennescnamenumens n Erecnnprmeaimeemerennirenis iaepcmaveinennorntinetinrencud


Document Created: 2017-01-06 01:50:40
Document Modified: 2017-01-06 01:50:40
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC