I19Z60566-SEM01_SAR_Rev0_part5

FCC ID: XD6U304AA

RF Exposure Info

Download: PDF
FCCID_4290042

No. I19Z60566-SEM01 Page 141 of 210 C.4.4 Device Holder for Phantom The SAR in the phantom is approximately inversely proportional to the square of the distance between the source and the liquid surface. For a source at 5mm distance, a positioning uncertainty of ±0.5mm would produce a SAR uncertainty of ±20%. Accurate device positioning is therefore crucial for accurate and repeatable measurements. The positions in which the devices must be measured are defined by the standards. The DASY device holder is designed to cope with the different positions given in the standard. It has two scales for device rotation (with respect to the body axis) and device inclination (with respect to the line between the ear reference points). The rotation centers for both scales is the ear reference point (ERP). Thus the device needs no repositioning when changing the angles. The DASY device holder is constructed of low-loss POM material having the following dielectric parameters: relative permittivity =3 and loss tangent  =0.02. The amount of dielectric material has been reduced in the closest vicinity of the device, since measurements have suggested that the influence of the clamp on the test results could thus be lowered. <Laptop Extension Kit> The extension is lightweight and made of POM, acrylic glass and foam. It fits easily on the upper part of the Mounting Device in place of the phone positioner. The extension is fully compatible with the Twin-SAM and ELI phantoms. Picture C.9-1: Device Holder Picture C.9-2: Laptop Extension Kit C.4.5 Phantom The SAM Twin Phantom V4.0 is constructed of a fiberglass shell integrated in a table. The shape of the shell is based on data from an anatomical study designed to Represent the 90th percentile of the population. The phantom enables the dissymmetric evaluation of SAR for both left and right handed handset usage, as well as body-worn usage using the flat phantom region. Reference markings on the Phantom allow the complete setup of all predefined phantom positions and measurement grids by manually teaching three points in the robot. The shell phantom has a 2mm shell thickness (except the ear region where shell thickness increases to 6 mm). Shell Thickness: 2 ± 0. 2 mm Filling Volume: Approx. 25 liters Dimensions: 810 x l000 x 500 mm (H x L x W) Available: Special ©Copyright. All rights reserved by CTTL.

No. I19Z60566-SEM01 Page 142 of 210 Picture C.10: SAM Twin Phantom ©Copyright. All rights reserved by CTTL.

No. I19Z60566-SEM01 Page 143 of 210 ANNEX D Position of the wireless device in relation to the phantom D.1 General considerations This standard specifies two handset test positions against the head phantom – the “cheek” position and the “tilt” position. wt Width of the handset at the level of the acoustic wb Width of the bottom of the handset A Midpoint of the width wt of the handset at the level of the acoustic output B Midpoint of the width wb of the bottom of the handset Picture D.1-a Typical “fixed” case handset Picture D.1-b Typical “clam-shell” case handset Picture D.2 Cheek position of the wireless device on the left side of SAM ©Copyright. All rights reserved by CTTL.

No. I19Z60566-SEM01 Page 144 of 210 Picture D.3 Tilt position of the wireless device on the left side of SAM D.2 Body-worn device A typical example of a body-worn device is a mobile phone, wireless enabled PDA or other battery operated wireless device with the ability to transmit while mounted on a person’s body using a carry accessory approved by the wireless device manufacturer. Picture D.4 Test positions for body-worn devices D.3 Desktop device A typical example of a desktop device is a wireless enabled desktop computer placed on a table or desk when used. The DUT shall be positioned at the distance and in the orientation to the phantom that corresponds to the intended use as specified by the manufacturer in the user instructions. For devices that employ an external antenna with variable positions, tests shall be performed for all antenna positions specified. Picture 8.5 show positions for desktop device SAR tests. If the intended use is not specified, the device shall be tested directly against the flat phantom. ©Copyright. All rights reserved by CTTL.

No. I19Z60566-SEM01 Page 145 of 210 Picture D.5 Test positions for desktop devices D.4 DUT Setup Photos Picture D.6 ©Copyright. All rights reserved by CTTL.

No. I19Z60566-SEM01 Page 146 of 210 ANNEX E Equivalent Media Recipes The liquid used for the frequency range of 800-3000 MHz consisted of water, sugar, salt, preventol, glycol monobutyl and Cellulose. The liquid has been previously proven to be suited for worst-case. The Table E.1 shows the detail solution. It’s satisfying the latest tissue dielectric parameters requirements proposed by the IEEE 1528 and IEC 62209. Table E.1: Composition of the Tissue Equivalent Matter Frequency 835 835 1900 1900 2450 2450 5800 5800 (MHz) Head Body Head Body Head Body Head Body Ingredients (% by weight) Water 41.45 52.5 55.242 69.91 58.79 72.60 65.53 65.53 Sugar 56.0 45.0 \ \ \ \ \ \ Salt 1.45 1.4 0.306 0.13 0.06 0.18 \ \ Preventol 0.1 0.1 \ \ \ \ \ \ Cellulose 1.0 1.0 \ \ \ \ \ \ Glycol \ \ 44.452 29.96 41.15 27.22 \ \ Monobutyl Diethylenglycol \ \ \ \ \ \ 17.24 17.24 monohexylether Triton X-100 \ \ \ \ \ \ 17.24 17.24 Dielectric ε=41.5 ε=55.2 ε=40.0 ε=53.3 ε=39.2 ε=52.7 ε=35.3 ε=48.2 Parameters σ=0.90 σ=0.97 σ=1.40 σ=1.52 σ=1.80 σ=1.95 σ=5.27 σ=6.00 Target Value Note: There are a little adjustment respectively for 750, 1750 and 2300 based on the recipe of closest frequency in table E.1. ©Copyright. All rights reserved by CTTL.

No. I19Z60566-SEM01 Page 147 of 210 ANNEX F System Validation The SAR system must be validated against its performance specifications before it is deployed. When SAR probes, system components or software are changed, upgraded or recalibrated, these must be validated with the SAR system(s) that operates with such components. Table F.1: System Validation for 7514 Probe SN. Liquid name Validation date Frequency point Status (OK or Not) 7514 Head 750MHz Sep.10,2018 750 MHz OK 7514 Head 850MHz Sep.10,2018 835 MHz OK 7514 Head 900MHz Sep.10,2018 900 MHz OK 7514 Head 1750MHz Sep.10,2018 1750 MHz OK 7514 Head 1810MHz Sep.10,2018 1810 MHz OK 7514 Head 1900MHz Sep.11,2018 1900 MHz OK 7514 Head 2000MHz Sep.11,2018 2000 MHz OK 7514 Head 2100MHz Sep.11,2018 2100 MHz OK 7514 Head 2300MHz Sep.11,2018 2300 MHz OK 7514 Head 2450MHz Sep.11,2018 2450 MHz OK 7514 Head 2600MHz Sep.12,2018 2600 MHz OK 7514 Head 3500MHz Sep.12,2018 3500 MHz OK 7514 Head 3700MHz Sep.12,2018 3700 MHz OK 7514 Head 5200MHz Sep.12,2018 5250 MHz OK 7514 Head 5500MHz Sep.12,2018 5600 MHz OK 7514 Head 5800MHz Sep.12,2018 5800 MHz OK 7514 Body 750MHz Sep.12,2018 750 MHz OK 7514 Body 850MHz Sep.9,2018 835 MHz OK 7514 Body 900MHz Sep.9,2018 900 MHz OK 7514 Body 1750MHz Sep.9,2018 1750 MHz OK 7514 Body 1810MHz Sep.9,2018 1810 MHz OK 7514 Body 1900MHz Sep.9,2018 1900 MHz OK 7514 Body 2000MHz Sep.13,2018 2000 MHz OK 7514 Body 2100MHz Sep.13,2018 2100 MHz OK 7514 Body 2300MHz Sep.13,2018 2300 MHz OK 7514 Body 2450MHz Sep.13,2018 2450 MHz OK 7514 Body 2600MHz Sep.13,2018 2600 MHz OK 7514 Body 3500MHz Sep.8,2018 3500 MHz OK 7514 Body 3700MHz Sep.8,2018 3700 MHz OK 7514 Body 5200MHz Sep.8,2018 5250 MHz OK 7514 Body 5500MHz Sep.8,2018 5600 MHz OK 7514 Body 5800MHz Sep.8,2018 5800 MHz OK ©Copyright. All rights reserved by CTTL.

No. I19Z60566-SEM01 Page 148 of 210 ANNEX G Probe Calibration Certificate Probe 7514 Calibration Certificate ©Copyright. All rights reserved by CTTL.

Calibration f Laboratory of g._ Setmaizenischer Kallborerdionst Schmid & Partner £5 Service suisso ditalonnage Engineering AG go . Servito avizzero d taratura Zeughausstrasse 83, 6004 zurich, Switzeriand ow Swiss Caliration Service Accredted by the Snss Accrodtation Sorvce (GAS) Accreditaion No.: SCS 0108 The Swiss Accreditaion Service is one of the signstoris to te CA Multlateral Agroementfotherecognitiono catlration certates Glossary: TSL tissue simuleting lquid NORMy,z sensitvily in free space Come sensitvily in TSL / NORMcy;z bcP diode compression point or crest factor (1‘duty.cycle) ofthe RF signal A, 8. C, D modulation dependent inearization parameters Polarization o «» rotation around probe axis Polarization 8 8 rotation around an axis that iin the plane normalto probe axis (at measurement center), i. 0 =0 is normal to probe axis Connector Angle information used in DASY system to align probe sensor X to the robot coordinate system Calibration is Performed According to the Following Standards: a) 1EEE Std 1528—2013, ‘EEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR)in the Human Head from Wireless Communications Devices: Measurement Techniques®, June 2013 b) 1€C 62208—1, *, "Measurement procedure forthe assessmentof Specific Absorplion Rate (SAR) from hand— held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)°, July 2016 c) 12C 62200—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximityto the human body (fequency range of 30 MHiz to 6 GHz)*, March 2010 d) KDB 865664, SAR Measurement Requirements for 100 MHz to 6 GHz" Methods Applied and Interpretation of Parameters: NORMy,z: Assessed for E—field polarization 8 = 0 (f 900 MHz in TEM—call 1 > 1800 MHz: R22 waveguide). NORy,z are only intermediate values, i.,the uncertainties of NORMxy,z does not affect the E"—field uncertainty inside TSL(see below ConF). NORM(xy,z = NORMxy.z * frequency.response (see Frequency Response Chart}. This Incarization is implemented in DASY4 software versions latethan 4.2. The uncertainty of the frequency response is included in the stated uncertainty of ConvF. DCPxy,a: DCP are numerical inearization parameters assessed based on the data of power sweep with CW signal (no uncertainty required). DCP does not depend on frequency nor media. PAR: PAR is the Peak to Average Ratlo thatis not callbrated but determined based on the signal characteristics Auya; Bxy.z:Cay,z:Dxy.z; VRxy,z: A, B, C, D are numerical inearization parameters assessed based on the date of power sweep for specific modulation signal. The parameters do not depend on frequency nor media. VR is the maximum calibration range expressed in RMS vaitage across the diode. Convand Boundary Effect Parameters: Assessein flat phantom using E—feld (or Temperature Transfer Standard forf s 800 MHz) and inside waveguide using analyticalfld distributions based on power measurements for > 800 MHiz. The same setups are used for assessment of the parameters applied for boundary compensation (alpha, depth) of which typical uncertainty values are given. These parameters are used in DASY4 software to improve probe accuracy close to the boundary. The sensitvityin TSL corresponds to NORMzy.z " Conv whereby the uncertainty corresponds to that given for Cony. A frequency dependent ConvF is used in DASY version 4.4 and higher which allows extencing the validty from : 50 MHz to + 100 NMHz. Spherieal isotropy (3D deviation from isotropy); in a field of low gradients realized using a fat phantom exposed by a patchantenna. Sensor Offset: The sensor offset corresponds to the offset of viuial measurement center from the probe tip (on probe axs). No tolerance required. Connector Angle: The angle is assessed using the information gained by determining the NORMs (no uncertainty required) Centicate No: EX3—7514_Aug18 Page 2 0f 30

exsovs — sNtrst4 August 27,2018 Probe EX3DV4 SN:7514 Manufactured: November 13, 2017 Calibrated: August 27, 2018 Calibrated for DASY/EASY Systems (Note: non—compatible with DASY2 system!) Cortficate No: EX3—7514_Aug18 Page 3 of 30

exsove—snizste August 27, 2018 DASY/EASY — Parameters of Probe: EX3DV4 — SN:7514 Basic Calibration Parameters Sensor X SensorY | SensorZ Une (i22) Norm (uViVim)3 046 o44 1 ose £10.1% DoF (av)" ses oi 1 ors Modulation Calibration Parameters us Communication System Name A s c 6 ve Une® as abvay as my (2) o ow x|_co oo o on mai s5% v 00 c0 10 is 2 |_oo oo 10 se Note: For detail on UID parameters see Appendi. Sensor Model Parameters a m T2 Ts Ts Ts To i€ i2 v= msN* |_moX~! ms ve vi x 3147 241.1 37.77 3605 0.025 5.031 0.000 0325 1.005 Y 34.00 250.7 3541 Tate 0.000 5.026 0323 0201 1002 H 36.14 250.6 36.05 3627 0.254 5046 0.000 0373 1.008 The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95% . 5 the uncetainies oNom XY.t do not affcthe Eeld uncetainlinside TSL (seo Pages 5 and 6) " Numerical Inoarizaton parameteruncertany notrequres. * Uncedainyis dternined using e max.devalionfom Inco esponse apnyingrectangularcisbationand is expressed fo hesquereofhe feld valve. Corticate No: EXG—7514_Augt8 Page 4 of 30

Excove—sN7s14 August 27, 2018 DASY/EASY — Parameters of Probe: EX3DV4 — SN:7514 Calibration Parameter Determined in Head Tissue Simulating Media Relative Condustty T beph Une £(uhin)© |_Pormittvity® (Sim)® ComFX ComvEY | GonvEZ Alpha® |__(mm) (kem) 150 s2s oze 1270 i27e iaze ose i00 s133% 200 453 os7 ms? ms? i18? oor 120 a183% 4so 435 o7 1oes foss ioes on 120 +183% 750 418 o.se o7 sar 947 oas oss £120% sas «15 0.s0 one a.09 a.09 oss oss +120% 200 415 o7 o03 a03 a.03 o4s oss 2120% 1480 «05 120 824 a24 a24 oss oso +120% 1640 402 131 s22 a22 aze oms ost £120% 170 40.1 137 810 a.10 a10_| oss oss +120% 1810 400 140 zse 1ee Tee oss ost +120% 1900 400 140 z2s z33 73e os1 oso +120% 2000 400 140 zse 7ea zes oso ost 2120% 2100 sos 149 z5t 757 Leu oar oss £120% 2300 sos 167 zaz 742 742 ost oso £120% 2450 so2 180 635 s95 65 oss oss +120% 2600 so0 186 692 s92 602 oms 105 +120% 3500 sre 201 ore ar8 o8 ore ost a131% 3700 o7.7 312 s1 s1 se1 o4 oss £19.1% s200 se 466 sos sos 505 o40 180 a18.1% seso s50 471 5o2 sor 502 o0 180 a131% se00 350 476 40e 409 4.99 o4 180 £181% 5500 356 498 aso as0 ass | o« 180 181% se00 s55 sor aan a41 as1_| oso 180 s131% s7so ss4 522 447 a47 447 o0 180 a131% seoo s53 s27 442 a42 442 o« 180 a181% © Frequency vality above 300 Wz of x 100 MHz onl appiesfoDASY .4 and Nigrer (se Page2elso t is resticted to + 50Mz The uncerainy s theRBS ofthe GoovE uncetinyat caloration rauency and the uncetintyfo e inicate requency band. Frequency valdty peto at 190Nt is 50 MHz. Above 5 Ge frequencyvadiy can bo extended to 2 10 N. Atftoquendies below 3 Gitz,the valdy oflssue parameters(sand ) can b relareto # 10% i loutd compensation omutais agled t imeasured SAvalus, t reavencies atove 3 GHe.thevaldiy o Ussue parameters (and a) is restfted o# $%. The uncertainy s the RSS of tne Gorveuncetaintfo inclcate trget tsoue parametors. * Aphe/Deotharedetermined dutngcalbratonSPEAG varranstattheremining deviaton duetothe boundary effect fter compensation is ahways lessthan 19 fo raquencies below 3 GHz and below # 2% fo requencies baten 28 GHizat any dstance largerthan hal the probet diametertrom the boundory Gertficate No: EX3—7514_Augte Page 5 of 30

®covs—sNzsie August 27, 2018 DASY/EASY — Parameters of Probe: EX3DV4 — SN:7514 Calibration Parameter Determined in Body Tissue Simulating Media Relative Condustivity bepth® Une £(ukin® |_Pormitivity® (Sm)" ComPX ComEY ComEZ Aipha® |__(mm) (ea) 150 s1.9 080 i2as i2as i2as on i0 e133% 300 se2 082 i13 i13e i138 ons 120 a133% aso ser 084 m3 13x m3 ons i2 e133% 750 se5 ose ass se8 ase ost 104 2120% sas seo o7 o4r oar 947 ous os0 +120% 200 550 105 934 934 o.34 ous oss +120% 1450 s4.0 130 a0e ao2 s.02 ost os0 +120% 1640 ser 142 735 185 7.es o42 ost £120% 17e0 se4 149 78 782 reo ose oss +120% 1810 se3 182 zse 169 Leeo ose os +120% 1900 ses 182 z53 zs3 Tss oss oss +120% 2000 ses 152 7as zas 7as ose oso 1120% 2100 sa2 182 730 730 130 ose om +120% 2300 s20 181 7as z2s ues osr oss £120% 2450 se.r 185 Tis 7is Tis ose osr +120% 2500 s25 216 708 708 706 om 110 +120% 2500 s13 s31 o85 s85 sss on 100 a181% 3700 51.0 ase ars a7s es om 10 a131% 5200 490 s30 aso aso «se oso 180 a18.1% soso 480 536 454 454 ase oso 18 r131% seoo 189 s42 449 449 «40| oso 180 a181% 5500 186 ses 447 417 a17 oso 180 a131% 5600 48.5 57 400 4.00 4.00 0.50 1.90 #13.4% s7so 183 504 s38 s98 see oso 1890 a181% seoo 182 6.00 320 394 ss oso 18 a181% 5 Erequency valityabove 300 itz of x 100 Mz ony aplesforDASY vi.4and higher se Page2else i restictadto+ S0 ME The uneerainy is the RSS ofthe ConvEuncerainy at aliraton reqsency and thauncetainy fotha iclcted raquency band. Frequency valdiy balow at 150 it is2 50 MHz. Above S Gz frequeney valiiy can be extended to 2 10 NHz. * Attrequencias below 3 Gite, the vadty of ssuo paramelers(s and a) can be relased t + 10% i Iqul compensaton formuta s aplld to measured SA valus, t requencias above 3 GHe,thevaldity o ssue paramolers (and #)i restiledto + 5%. Thuncertainy is the RSS of tne Gorn£ urcetaintfoinicated trgettsoue parametors ° Alpha/Dopinare deternined curing caltraton. SPEAG wartnts hat the remaining devitiondueto he bounday efecatercompensationis avays lessthan : 19 fofequenciosbelow 3 GHz and below + 2% forfegvencas betueen 26 GHi at ny dstance largorthan halthe probe t dameterfom the boondoy. Certicate No: EX3—7514_Augte Page 6or 30

©xcove—sNzsne August 27,2018 Frequency Response of E—Field Frequency response (normalized) (TEM—Cel 110 EXX, Waveguide: R22) Uncertainty of Frequency Response of E—field: 2 6.3% (k=2) Centicate No: EX3—7514_Augto Page 7 of 30

exove—snzste August 27,2018 Receiving Pattern (¢), 9 = 0° £=600 MHz,TEM 121800 MHz,R22 + wl x. «s To x 4 roir) whtle «ht s Uncertainty of Axial Isotropy Assessment: £.0.5% (k=2) Certfcate No: EX3—7514_Augt8 Page 8 of 30

exsovs~stizste August 27, 2018 Dynamic Range f(SARneaq) (TEM cell , fevar= 1900 MH2z) Input Signal uV * * 7 t0° 101 10 10 10 10 SAR {mWoms] not compensated wrnglsmd Eror gB) . 1 d1 do tor too SAR [mWiem?] net compansnted compensated Uncertainty of Linearity Assossmont: £ 0.6% (k=2) Certficate No: EXG—7514_Augto Page 9 or30

Exsove— sN751¢ August 27, 2018 Conversion Factor Assessment 1= 900 MHz.WGLS Ro (4_com) 1= 1810 MHzWGLS R22 (1_cons?) ,» ? & s so sppurms ol Bs * oaeg * #. — — ay * se 7 E. Deviation from Isotropy in Liquid Error (§, 8), £ = 900 MHz 10 cos cos .o« o2 oo o2 o4 os os 10 Uncertainty of Sphorical Isotropy Assossment: £ 2.6% (k=2) Cortficate No: EX3—7514_Augto Page 10 of 39

EX3DV4— SN:7514 August 27, 2018 DASY/EASY — Parameters of Probe: EX3DV4 — SN:7514 Other Probe Parameters Sensor Arrangement Triangular Connector Angle (°) —19.8 Mechanical Surface Detection Mode enabled Optical Surface Detection Mode disabled Probe Overall Length 337 mm Probe Body Diameter 10 mm Tip Length 9 mm Tip Diameter 2.5 mm Probe Tip to Sensor X Calibration Point 1 mm Probe Tip to Sensor Y Calibration Point 1 mm Probe Tip to Sensor Z Calibration Point 1 mm Recommended Measurement Distance from Surface 1.4 mm Certificate No: EX3—7514_Aug18 Page 11 of 39 Nn ey n n en n n n nge e n ++ >

No. I19Z60566-SEM01 Page 159 of 210 ANNEX H Dipole Calibration Certificate 750 MHz Dipole Calibration Certificate ©Copyright. All rights reserved by CTTL.

® Calibration B Laboratory of Schmid & Partner Engineering AG Zeughausstrasse 43, 0004 Zurich, Switzeriand Acoredted by the Sviss Accreditation Srvice (GAG) @g Sotweizerischer Kaliprierdionst Service suisse a‘italonnage Serviclo aviezero oi tarature S suiss Cattpration Sorvice Accreditation No.: SCS 0108 "The Swiss Accreditation Service is one of the signatories to the EA Mulltatera! Agreementforthe recognition of callation cortficatos Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM xy,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques®, June 2013 b IEC 62209—1, *Measurement procedure for the assessment of Specific Absorption Rate (SAR) from hand—held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)®, July 2016 c IEC 62209—2, "Procedureto determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)*, March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: * Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at thefrequency indicated. * Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. * Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filed phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. * Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. * SAR measured: SAR measured at the stated antenna input powor. * SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. * SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95% . Certficate No: D750V3—1017_Jult? Page 2 of 8

Measurement Conditions DASY system contiquration, as far as not given on page 1. DASY Version basvs vse.t00 Extrapolation Advanced Extrapolation Phantom Modular Fiat Phantomn Distance Dipole Center — TSL 15 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 750 Miz a 1 Miiz Head TSL parameters The following paramaters and calculations were apolied. Temperature Permittivity Conductivity Nominal Head TSL parameters 220°C a10 0.89 mhoim Measured Head TSL parameters @g2o02)°C 41.026% 0.9 mhoim 26 % Head TSL temperature change during test <as*c — SAR result with Head TSL SAR averaged over 1 om (1 g) of Head TSL Condition SAR measured 250 mW inout power 2.00 Whg SAR for nominal Hoad TSL parameters normalized to 1W 8.92 Whky = 17.0 % (kx?) SAR averaged over 10 em(10 g) of Head TSL condition SAR measured 250 mW input power 1.36 Wio SAR for nominal Head TSL parameters normalized to 1W 5.42 Wikg + 16.3 % (k=2) Body TSL parameters The following parameters and calculations were apglied. Temperature Permittivity Conductivity Nominal Body TSL. parameters 220°C sas 0.98 mhoim Measured Body TSL parameters @2002)°C s5.020% 0.99 mhoim &6 % Body TSL temperature change during test <o5*c ~— — SAR result with Body TSL SAR averaged over 1 cm‘ (1 g) of Body TSL Condiion SAR measured 250 mW inout power 222 Wiho SAR for nominal Body TSL parametars normalized to 1W 8.66 Wikg 2 17.0 % (k=2) SAR averaged over 10 om* (10 ) of Body TSL condition SAR measured 250 mW input power 145 Wig SAR for nominal Bady TSL parametors normalized to 1W 5.68 Whky £ 16. % (k=2) Cortficate No: D750V3—1017_Jult? Page 3 of8

e> 7TL P e Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL Impedance, transformed to feed point 54.4 2 10. jn Retum Loss +275 08 Antenna Parameters with Body TSL Impedance, transformed to feed point 4030 —3.4 n Retum Loss ~20.1 4B General Antenna Parameters and Design Electrieal Delay (one direction) 1.033 ns After long term use with 100W racieted power, only a sight warming of the dipole near the feedpoint can be meesured. The dipole is made of standard sermirigld coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—cirouited for DC—signals. On some ofthe dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions‘ paragragh. The SAR data are not affected by this change. The overall dipole length is stil according to the Standard. No excessive foree must be applied to the dipole arms, because they might bend or the soldered connections nearthe feedpoint may be damaged. Additional EUT Data Manutactured by spaae Manutactured on March 22, 2010 Certficate No: D7S0V3—1017_Junt7 Page 4 of 8

® DASY5 Validation Report for Head TSL Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 750 MHz; Type: D75OV3; Serial: D750V3 — SN:1017 Date: 19.07.2017 Communication System: UID 0 — CW; Frequency: 750 MHz Medium parameters used: £=750 MHz; o = 0.89 S/m; 6; = 41; p = 1000 kg/m‘ Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/EC/ANSI C63.19—2011) DASY52 Configuration: Probe: EX3DV4 — SN7349; ConvF(10.49, 10.49, 10.49); Calibrated: 31.05.2017; Sensor—Surface: 1.4mm (Mechanical Surace Detection) Electronics: DAE4 Sn601; Calibrated: 28.03.2017 Phantom: Flat Phantom 4.9 (front); Type: QD OOL P49 AA; Serial: 1001 DASY52 52.10.0(1446); SEMCAD X 14.6.10(7417) Dipole Calibration for Head Tissue/Pin=250 mW, d=15mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 58.85 V/m; Power Drift = 0.00 dB Peak SAR (extrapolated) = 3.22 W/kg SAR(L g) =2.09 W/kg; SAR(1O g) = 1.36 W/ke Maximum valueof SAR (measured) =2.83 W/kz —6.60 —8.00 —17.00 0 dB =2.83 Wikg = 4.52 dBWikg Certficate No: D7S0V3—1017_.Jult7 Page 5 of 8

omm I TTL F mm C Impedance Measurement Plot for Head TSL 18 Jul zeir estarise ERD sa i uis asessse esiore s800 pi 7s0.000 ooo ns m per e t° cne hy 159 Sthet sse.00 ooo ns stoe ssa.00 ace ie Certficate No: D7503—1017_Jult7 Page 6 of 8

® DASY5 Validation Report for Body TSL Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 750 MHz; Type: D750V3; Serial: D750V3 — SN:1017 Date: 19.07.2017 Communication System: UID 0 — CW; Frequency: 750 MHz Medium parameters used: f=750 MHz; a = 0.99 $/m; &; = 55; p = 1000 ke/m? Phantom section: Flat Section Measurement Standard: DASY5 (IEEEAMEC/ANSI C63.19—2011) DASY52 Configuration: * Probe: EX3DV4 — SN7349; ConvR(10.35, 10.35, 10.35); Calibrated: 31.05.2017; * Sensor—Surface: 1.4mm (Mechanical Surface Detection) * Electronics: DAE4 Sn601; Calibrated: 28.03.2017 * Phantom: Flat Phantom 4.9 (Back); Type: QD 0OR P49 AA; Serial: 1005 «_ DASY52 52.10.0(1446); SEMCAD X 14.6.10(7417) Dipole Calibration for Body Tissue/Pin=250 mW, d=15mm/Zoom Scan (7x7x7)/Cube 0: Measurementgrid: dx=5mm, dy=5mm, dz=5mm Reference Value = 57.67 V/m; Power Drift = —0.03 dB Peak SAR (extrapolated) = 3.34 W/kg SAR(I g) =2.22 W/kg; SAR(1O g) = Maximum valueof SAR (measured) = 2. —6.60 —11.00 0 dB =2.96 Wikg=4.71 dBWikg Cortficate No: D7S03—1017_.u17 Page 7 of 8


Document Created: 2019-05-13 13:16:49
Document Modified: 2019-05-13 13:16:49
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC