test report

FCC ID: XAM300011GR05

Test Report

Download: PDF
FCCID_2043663

FCC Measurement/Technical Report on RFID transceiver – part of Intrinsically Safe PDA i.roc® Ci70 Report Reference: MDE_ECOM_1202_FCCb Test Laboratory: Borsigstr. 11 Germany 7Layers AG 40880 Ratingen Note: The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts without the written approval of the test laboratory. 7 layers AG Aufsichtsratsvorsitzender Registergericht registered in: Borsigstrasse 11 Chairman of the Supervisory Board: Düsseldorf, HRB 44096 40880 Ratingen, Germany Ralf Mertens USt-IdNr  VAT No.: Phone: +49 (0) 2102 749 0 Vorstand Board: DE 203159652 Fax: +49 (0) 2102 749 350 Dr. H.-J. Meckelburg TAX No. 147/5869/0385 www.7Layers.com

Table of Contents 0 Summary 3 0.1 Technical Report Summary 3 0.2 Measurement Summary 4 1 Administrative Data 5 1.1 Testing Laboratory 5 1.2 Project Data 5 1.3 Applicant Data 5 1.4 Manufacturer Data 5 2 Test object Data 6 2.1 General EUT Description 6 2.2 EUT Main components 7 2.3 Ancillary Equipment 7 2.4 Auxiliary Equipment 7 2.5 EUT Setups 8 2.6 Operating Modes 8 3 Test Results 9 3.1 Spurious radiated emissions 9 3.2 Peak power output 14 3.3 Conducted emissions (AC power line) 15 4 Test Equipment 17 5 Photo Report 24 6 Setup Drawings 24 7 Annex measurement plots 25 7.1 Radiated emissions and peak output power 25 7.2 AC Mains conducted 31 Test report reference: MDE_ECOM_1202_FCCb Page 2 of 32

0 Summary 0.1 Technical Report Summary Type of Authorization Certification for an intentional radiator: 125, 128 and 134 kHz RFID transceiver Applicable FCC Rules Prepared in accordance with the requirements of FCC Rules and Regulations as listed in 47 CFR Ch.1 Parts 2 (10-1-11 Edition) and 15 (10-1-11 Edition). The following subparts are applicable to the results in this test report. Part 2, Subpart J - Equipment Authorization Procedures, Certification Part 15, Subpart C – Intentional Radiators § 15.205 Restricted bands of operation § 15.207 Conducted limits § 15.209 Radiated emission limits; general requirements § 15.215 Additional provisions to the general radiated emission limitations Note: None Summary Test Results: The EUT complied with all performed tests as listed in chapter 0.2 Measurement Summary. Test report reference: MDE_ECOM_1202_FCCb Page 3 of 32

0.2 Measurement Summary FCC Part 15, Subpart C §15.209 Radiated Emissions The measurement was performed according to ANSI C63.4 2009 OP-Mode Setup Port Final Result op-mode 1 Setup_01 Enclosure passed FCC Part 15, Subpart C § 15.209 Peak Output Power The measurement was performed according to ANSI C63.4 2009 OP-Mode Setup Port Final Result op-mode 1 Setup_01 Enclosure passed FCC Part 15, Subpart C § 15.207 Conducted Emissions AC Power line The measurement was performed according to ANSI C63.4 2009 OP-Mode Setup Port Final Result op-mode 1 Setup_01 AC-Mains passed Digitally signed by Marco Kullik Digitally signed by Andreas Petz DN: cn=Marco Kullik, sn=Kullik, DN: cn=Andreas Petz, sn=Petz, givenName=Marco, o=7 Layers AG, givenName=Andreas, o=7Layers AG, serialNumber=00100000000120290500 Responsible for Responsible serialNumber=00100000000120291800 02, email=Marco.Kullik@7Layers.de 01, email=andreas.petz@7layers.de Reason: I am the author of this Reason: I am approving this document Accreditation Scope: for Test Report: document Date: 2013.04.04 13:05:57 +02'00' Date: 2013.04.04 12:18:11 +02'00' Test report reference: MDE_ECOM_1202_FCCb Page 4 of 32

1 Administrative Data 1.1 Testing Laboratory Company Name: 7Layers AG Address Borsigstr. 11 40880 Ratingen Germany This facility has been fully described in a report submitted to the FCC and accepted under the registration number 96716. The test facility is also accredited by the following accreditation organisation: Laboratory accreditation no.: DAkkS D-PL-12140-01-01 Responsible for Accreditation Scope: Dipl.-Ing. Bernhard Retka Dipl.-Ing. Robert Machulec Dipl.-Ing. Andreas Petz Dipl. Ing. Marco Kullik Report Template Version: 2012-03-14 1.2 Project Data Responsible for testing and report: Dipl. Ing. Marco Kullik Date of Test(s): 2012-11-13 to 2013-03-01 Date of Report: 2013-03-28 1.3 Applicant Data Company Name: ECOM Instruments GmbH Address: Industriestraße 2 97959 Assamstadt Germany Contact Person: Mr. H. Fiederlein 1.4 Manufacturer Data Company Name: please see applicant data Address: Contact Person: Test report reference: MDE_ECOM_1202_FCCb Page 5 of 32

2 Test object Data 2.1 General EUT Description Equipment under Test Intrinsically Safe PDA i.roc® Type Designation: Ci70 Kind of Device: 125 / 128 / 134 kHz RFID Transceiver (optional) Voltage Type: DC (internal battery, Li-Ion) Voltage level: 3.7 V General product description: The EUT is a RFID transmitter, part of the Intrinsically Safe i.roc® Ci70 –Ex. It is a handheld PDA, which contains the wireless technologies WLAN 2.4 GHz with b, g and n modes, WLAN 5 GHz with a and n modes and Bluetooth. The EUT can be equipped with different RFID modules. For the tests according to this standard, a 125/134 kHz and a 128 kHz module was used. The EUT cannot be charged directly via an AC/DC adapter, this is only possible via an additional docking station. The EUT provides the following ports: Ports Enclosure AC Mains Port (AE 1) The main components of the EUT are listed and described in Chapter 2.2. Test report reference: MDE_ECOM_1202_FCCb Page 6 of 32

2.2 EUT Main components Type, S/N, Short Descriptions etc. used in this Test Report Short Equipment under Type Serial No. HW SW Date of Description Test Designation Status Status Receipt EUT A Intrinsically Safe PDA Ci70 22321245059 P5.2 1.50.19.0013 – (Code: (numeric) inkl. 4E000b01) TLB30-125/134 kHz EUT B Intrinsically Safe PDA Ci70 22321245060 P5.2 1.50.19.0013 – (Code: (alphanumeric) inkl. 4E000e01) LID-128 kHz NOTE: The short description is used to simplify the identification of the EUT in this test report. 2.3 Ancillary Equipment For the purposes of this test report, ancillary equipment is defined as equipment which is used in conjunction with the EUT to provide operational and control features to the EUT. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Ancillary Equipment can influence the test results. Short Description Equipment Type Serial No. HW SW FCC ID under Test Designation Status Status AE 1 – – AC/DC adapter 9004AE01 34351101811 01 Code: 4E000ACD AE 2 Code: Dual – – 1002UU02 222D1100216 01 4E000DSDnew Dock AE 3 LF Tag 125 kHz – 0017 – – – AE 4 LF Tag 134 kHz – – – – – AE 5 LF Tag 128 kHz Trovan ID200 – – – – 2.4 Auxiliary Equipment For the purposes of this test report, auxiliary equipment is defined as equipment which is used temporarily to enable operational and control features especially used for the tests of the EUT which is not used during normal operation or equipment that is used during the tests in combination with the EUT but is not subject of this test report. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Auxiliary Equipment can influence the test results. Short Description Equipment Type Serial No. HW SW FCC ID under Test Designation Status Status – – – – – – – Test report reference: MDE_ECOM_1202_FCCb Page 7 of 32

2.5 EUT Setups This chapter describes the combination of EUTs and ancillary equipment used for testing. Setup No. Combination of EUTs Description Setup_01 EUT A + AE 3 setup for radiated emissions in 125 kHz range Setup_02 EUT A + AE 4 setup for radiated emissions in 134 kHz range Setup_03 EUT B + AE 5 setup for radiated emissions in 128 kHz range Setup_04 EUT A + AE 1 + AE 2 + AE 3 setup for Conducted emissions (AC power line) measurements in 125 kHz range Setup_05 EUT A + AE 1 + AE 2 + AE 4 setup for Conducted emissions (AC power line) measurements in 134 kHz range Setup_06 EUT B + AE 1 + AE 2 + AE 5 setup for Conducted emissions (AC power line) measurements in 128 kHz range 2.6 Operating Modes This chapter describes the operating modes of the EUTs used for testing. Op. Mode Description of Operating Modes Remarks op-mode 1 unmodulated carrier signal EUT is transmitting a periodic unmodulated signal and is continuously reading TAG information at 125 kHz (TLB-30). op-mode 2 unmodulated carrier signal EUT is transmitting a periodic unmodulated signal and is continuously reading TAG information at 134 kHz (TLB-30). op-mode 3 unmodulated carrier signal EUT is transmitting a periodic unmodulated signal and is continuously reading TAG information at 128 kHz (LID). Test report reference: MDE_ECOM_1202_FCCb Page 8 of 32

3 Test Results 3.1 Spurious radiated emissions Standard FCC Part 15, Subpart C The test was performed according to: ANSI C63.4 3.1.1 Test Description The test set-up was made in accordance to the general provisions of ANSI C63.4 in a typical installation configuration. The Equipment Under Test (EUT) was set up on a non- conductive table 1.0 x 2.0 m² in the semi-anechoic chamber. The influence of the EUT support table that is used between 30–1000 MHz was evaluated. The measurement procedure is implemented into the EMI test software ES-K1 from R&S. Exploratory tests are performed at 3 orthogonal axes to determine the worst-case orientation of a body-worn or handheld EUT. The final test on all kind of EUTs is performed at 2 axes. A pre-check is also performed while the EUT is powered from both AC and DC (battery) power in order to find the worst-case operating condition. 1. Measurement up to 30 MHz The Loop antenna HFH2-Z2 is used. Step 1: pre-measurement - Anechoic chamber - Antenna distance: 10 m - Detector: Peak-Maxhold - Frequency range: 0.009 – 0.15 and 0.15 – 30 MHz - Frequency steps: 0.1 kHz and 5 kHz - IF–Bandwidth: 0.2 kHz and 10 kHz - Measuring time / Frequency step: 100 ms Intention of this step is, to determine the radiated EMI-profile of the EUT. Afterwards the relevant emissions for the final measurement are identified. Step 2: final measurement For the relevant emissions determined in step 1, an additional measurement with the following settings will be performed. Intention of this step is to find the maximum emission level. - Open area test side - Antenna distance: according to the Standard - Detector: Quasi-Peak - Frequency range: 0.009 – 30 MHz - Frequency steps: measurement at frequencies detected in step 1 - IF–Bandwidth: 200 Hz – 10 kHz - Measuring time / Frequency step: 100 ms Test report reference: MDE_ECOM_1202_FCCb Page 9 of 32

2. Measurement above 30 MHz and up to 1 GHz Step 1: Preliminary scan Preliminary test to identify the highest amplitudes relative to the limit. Settings for step 1: - Antenna distance: 3 m - Detector: Peak-Maxhold - Frequency range: 30 – 1000 MHz - Frequency steps: 60 kHz - IF–Bandwidth: 120 kHz - Measuring time / Frequency step: 100 µs - Turntable angle range: –180° to 180° - Turntable step size: 90° - Height variation range: 1 – 3 m - Height variation step size: 2 m - Polarisation: Horizontal + Vertical Intention of this step is, to determine the radiated EMI-profile of the EUT. Afterwards the relevant emissions for the final measurement are identified. Step 2: second measurement For the relevant emissions determined in step 1, an additional measurement with the following settings will be performed. Intention of this step is, to find out the approximate turntable angle and antenna height for each frequency. - Detector: Peak – Maxhold - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 100 ms - Turntable angle range: –180° to 180° - Turntable step size: 45° - Height variation range: 1 – 4 m - Height variation step size: 0.5 m - Polarisation: horizontal + vertical After this step the EMI test system has determined the following values for each frequency (of step 1): - Frequency - Azimuth value (of turntable) - Antenna height The last two values have now the following accuracy: - Azimuth value (of turntable): 45° - Antenna height: 0.5 m Step 3: final measurement In this step the accuracy of the turntable azimuth and antenna height will be improved. This is necessary to find out the maximum value of every frequency. For each frequency, which was determined the turntable azimuth and antenna height will be adjusted. The turntable azimuth will be slowly varied by +/– 22.5° around this value. During this action the value of emission is continuously measured. The turntable azimuth at the highest emission will be recorded and adjusted. In this position the antenna height is also slowly varied by +/– 25 cm around the antenna height determined. During this action the value of emission is also continuously measured. The antenna height of the highest emission will also be recorded and adjusted. - Detector: Peak – Maxhold - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 100 ms - Turntable angle range: –22.5° to +22.5° around the determined value - Height variation range: –0.25 m to +0.25 m around the determined value Test report reference: MDE_ECOM_1202_FCCb Page 10 of 32

Step 4: final measurement with QP detector With the settings determined in step 3, the final measurement will be performed: EMI receiver settings for step 4: - Detector: Quasi-Peak(< 1 GHz) - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 1 s After the measurement a plot will be generated which contains a diagram with the results of the preliminary scan and a chart with the frequencies and values of the results of the final measurement. 3. Measurement above 1 GHz The following modifications apply to the measurement procedure for the frequency range above 1 GHz: The Equipment Under Test (EUT) was set up on a non-conductive support at 1.4 m height in the fully-anechoic chamber. The measurement distance was reduced to 1 m. The results were extrapolated by the extrapolation factor of 20 dB/decade (inverse linear distance for field strength measurements, inverse linear-distance squared for the power reference level measurements). Due to the fact that in this frequency range a double ridged wave guided horn antenna (up to 18 GHz) and a horn antenna (18-25 GHz) are used, the steps 2-4 are omitted. Step 1 was performed with one height of the receiving antenna only. EMI receiver settings: - Detector: Peak, Average - IF Bandwidth = 1 MHz 3.1.2 Test Requirements / Limits FCC Part 15, Subpart C, §15.209, Radiated Emission Limits Frequency in MHz Limit (µV/m) Measurement distance (m) Limit(dBµV/m @10m) 0.009 – 0.49 2400/F(kHz) 300 Limit (dBµV/m)+59.1dB 0.49 – 1.705 24000/F(kHz) 30 Limit (dBµV/m)+19.1dB 1.705 – 30 30 30 Limit (dBµV/m)+19.1dB Frequency in MHz Limit (µV/m) Measurement distance (m) Limit (dBµV/m) 30 – 88 100 3 40.0 88 – 216 150 3 43.5 216 – 960 200 3 46.0 above 960 500 3 54.0 §15.35(b) ..., there is also a limit on the radio frequency emissions, as measured using instrumentation with a peak detector function, corresponding to 20 dB above the maximum permitted average limit.... Used conversion factor: Limit (dBµV/m) = 20 log (Limit (µV/m)/1µV/m) Test report reference: MDE_ECOM_1202_FCCb Page 11 of 32

3.1.3 Test Protocol Temperature: 22 °C Air Pressure: 1009 – 1015 hPa Humidity: 32 – 33 % 3.1.3.1 Measurement up to 30 MHz Op. Mode Setup Port op-mode 1 Setup_01 Enclosure Polari- Frequency Corrected value Limit Limit Limit Delta to Delta to sation MHz dBµV/m dBµV/ dBµV/ dBµV/ limit limit m m m dB dB QP Peak AV QP Peak AV QP/Peak AV – – – – – – – – – – Remark: Please see annex for the measurement plots. No relevant spurious emissions found, therefore step 2 was not performed. Op. Mode Setup Port op-mode 2 Setup_02 Enclosure Polari- Frequency Corrected value Limit Limit Limit Delta to Delta to sation MHz dBµV/m dBµV/ dBµV/ dBµV/ limit limit m m m dB dB QP Peak AV QP Peak AV QP/Peak AV – – – – – – – – – – Remark: Please see annex for the measurement plots. No relevant spurious emissions found, therefore step 2 was not performed. Op. Mode Setup Port op-mode 3 Setup_03 Enclosure Polari- Frequency Corrected value Limit Limit Limit Delta to Delta to sation MHz dBµV/m dBµV/ dBµV/ dBµV/ limit limit m m m dB dB QP Peak AV QP Peak AV QP/Peak AV – – – – – – – – – – Remark: Please see annex for the measurement plots. No relevant spurious emissions found, therefore step 2 was not performed. Test report reference: MDE_ECOM_1202_FCCb Page 12 of 32

3.1.3.2 Measurement above 30 MHz Op. Mode Setup Port op-mode 1 Setup_01 Enclosure Polari- Frequency Corrected value Limit Limit Limit Delta to Delta to sation MHz dBµV/m dBµV/ dBµV/ dBµV/ limit limit m m m dB dB QP Peak AV QP Peak AV QP/Peak AV – – – – – – – – – – Remark: No (further) spurious emissions in the range 20 dB below the limit found. Op. Mode Setup Port op-mode 2 Setup_02 Enclosure Polari- Frequency Corrected value Limit Limit Limit Delta to Delta to sation MHz dBµV/m dBµV/ dBµV/ dBµV/ limit limit m m m dB dB QP Peak AV QP Peak AV QP/Peak AV – – – – – – – – – – Remark: No (further) spurious emissions in the range 20 dB below the limit found. Op. Mode Setup Port op-mode 3 Setup_03 Enclosure Polari- Frequency Corrected value Limit Limit Limit Delta to Delta to sation MHz dBµV/m dBµV/ dBµV/ dBµV/ limit limit m m m dB dB QP Peak AV QP Peak AV QP/Peak AV – – – – – – – – – – Remark: No (further) spurious emissions in the range 20 dB below the limit found. 3.1.4 Test result: Spurious radiated emissions FCC Part 15, Subpart C Op. Mode Result op-mode 1 passed op-mode 2 passed op-mode 3 passed Test report reference: MDE_ECOM_1202_FCCb Page 13 of 32

3.2 Peak power output Standard FCC Part 15, Subpart C The test was performed according to: FCC §15.209, ANSI C63.4 3.2.1 Test Description Please refer to sub-clause 3.1.1. 3.2.2 Test Limits Please refer to sub-clause 3.1.2. 3.2.3 Test Protocol Temperature: 22 °C Air Pressure: 1015 hPa Humidity: 33 % Op. Mode Setup Port op-mode 1 Setup_01 Enclosure Output power Frequency Limit dBµV/m at fundamental Remarks dBµV/m kHz frequency for 10 m distance 47.3 125.3 84.8 Maximum radiated field strength at fundamental frequency Op. Mode Setup Port op-mode 2 Setup_02 Enclosure Output power Frequency Limit dBµV/m at fundamental Remarks dBµV/m kHz frequency for 10 m distance 47.6 133.7 84.2 Maximum radiated field strength at fundamental frequency Op. Mode Setup Port op-mode 3 Setup_03 Enclosure Output power Frequency Limit dBµV/m at fundamental Remarks dBµV/m kHz frequency for 10 m distance 70.3 128.2 84.6 Maximum radiated field strength at fundamental frequency 3.2.4 Test result: Peak power output FCC Part 15, Subpart C Op. Mode Result op-mode 1 passed op-mode 2 passed op-mode 3 passed Test report reference: MDE_ECOM_1202_FCCb Page 14 of 32

3.3 Conducted emissions (AC power line) Standard FCC Part 15, Subpart C The test was performed according to: ANSI C63.4 3.3.1 Test Description The test set-up was made in accordance to the general provisions of ANSI C63.4. The Equipment Under Test (EUT) was setup in a shielded room to perform the conducted emissions measurements in a typical installation configuration. The EUT was powered from 50µH || 50 Ohm Line Impedance Stabilization Network (LISN). which meets the requirements of ANSI C63.4, Annex B, in the frequency range of the measurements. The LISN’s unused connections were terminated with 50 Ohm loads. The measurement procedure consists of two steps. It is implemented into the EMI test software ES-K1 from R&S. Step 1: Preliminary scan Intention of this step is, to determine the conducted EMI-profile of the EUT. EMI receiver settings: - Detector: Peak - Maxhold - Frequency range: 150 kHz – 30 MHz - Frequency steps: 5 kHz - IF–Bandwidth: 9 kHz - Measuring time / Frequency step: 20 ms - Measurement on phase + neutral lines of the power cords - AC Mains supplied at 120 V / 60 Hz. On basis of this preliminary scan the highest amplitudes and the corresponding frequencies relative to the limit are identified. Emissions above the limit and emissions which are in the 10 dB range below the limit are considered. Step 2: Final measurement Intention of this step is, to determine the highest emissions with the settings defined in the test specification for the frequencies identified in step 1. EMI receiver settings: - Detector: Quasi-Peak - IF - Bandwidth: 9 kHz - Measuring time: 1 s / frequency At each frequency determined in step 1, four measurements are performed in the following combinations: 1) Neutral lead - reference ground (PE grounded) 2) Phase lead - reference ground (PE grounded) 3) Neutral lead - reference ground (PE floating) 4) Phase lead - reference ground (PE floating) The highest value is reported. The chosen operating mode is selected as representative mode to generate “worst-case” conditions, i.e. high power consumption. Test report reference: MDE_ECOM_1202_FCCb Page 15 of 32

3.3.2 Test Requirements / Limits FCC Part 15, Subpart C, §15.207 Frequency Range (MHz) QP Limit (dBµV) AV Limit (dBµV) 0.15 – 0.5 66 to 56 56 to 46 0.5 – 5 56 46 5 – 30 60 50 Used conversion factor: Limit (dBµV) = 20 log (Limit (µV)/1µV). 3.3.3 Test Protocol Temperature: 23 °C Air Pressure: 1037 hPa Humidity: 37 % Op. Mode Setup Port op-mode 1 Setup_04 AC-Port Power Frequency Measured value Delta to limit Remarks line MHz dBµV dBµV L1 0.565 37.4 8.6 AV-detector Op. Mode Setup Port op-mode 2 Setup_05 AC-Port Power Frequency Measured value Delta to limit Remarks line MHz dBµV dBµV – – – – – Op. Mode Setup Port op-mode 3 Setup_06 AC-Port Power Frequency Measured value Delta to limit Remarks line MHz dBµV dBµV – – – – – Remark: Please see annex for the measurement plot. 3.3.4 Test result: Conducted emissions (AC power line) FCC Part 15, Subpart C Op. Mode Result op-mode 1 passed op-mode 2 passed op-mode 3 passed Test report reference: MDE_ECOM_1202_FCCb Page 16 of 32

4 Test Equipment The calibration, hardware and software states are shown for the testing period. Test Equipment Anechoic Chamber Lab ID: Lab 3 Manufacturer: Frankonia Description: Anechoic Chamber for radiated testing Type: 10.58x6.38x6.00 m³ Single Devices for Anechoic Chamber Single Device Name Type Serial Number Manufacturer Air compressor none - Atlas Copco Anechoic Chamber 10.58 x 6.38 x 6.00 m³ none Frankonia FCC listing 96716 3m Part15/18 2011/01/11 2014/01/10 IC listing 3699A-1 3m 2011/02/07 2014/02/06 Controller Maturo MCU 961208 Maturo GmbH EMC camera CE-CAM/1 - CE-SYS EMC camera Nr.2 CCD-400E 0005033 Mitsubishi Filter ISDN B84312-C110-E1 Siemens&Matsushita Filter Universal 1A BB4312-C30-H3 - Siemens&Matsushita Test Equipment Auxiliary Equipment for Conducted emissions Lab ID: Lab 1 Manufacturer: Rohde & Schwarz GmbH & Co.KG Description: EMI Conducted Auxiliary Equipment Single Devices for Auxiliary Equipment for Conducted emissions Single Device Name Type Serial Number Manufacturer AC Power Source Chroma 6404 64040001304 Chroma ATE INC. Cable "LISN to ESI" RG214 W18.03+W48.03 Huber&Suhner Path Calibration 2011/11/11 2012/11/10 Two-Line V-Network ESH 3-Z5 828304/029 Rohde & Schwarz GmbH & Co. KG Two-Line V-Network ESH 3-Z5 829996/002 Rohde & Schwarz GmbH & Co. KG DKD calibration 2011/01/20 2013/01/19 Test report reference: MDE_ECOM_1202_FCCb Page 17 of 32

Test Equipment Auxiliary Equipment for Radiated emissions Lab ID: Lab 3 Description: Equipment for emission measurements Serial Number: see single devices Single Devices for Auxiliary Equipment for Radiated emissions Single Device Name Type Serial Number Manufacturer Antenna mast AS 620 P 620/37 HD GmbH Biconical dipole VUBA 9117 9117-108 Schwarzbeck Calibration Details Last Execution Next Exec. Standard Calibration 2008/10/27 2013/10/26 Standard Calibration 2012/01/18 2015/01/17 Broadband Amplifier JS4-18002600-32-5P 849785 Miteq 18MHz-26GHz Path Calibration 2012/05/24 2012/11/23 Broadband Amplifier AFS4-01000400-1Q-10P-4 - Miteq 1GHz-4GHz Path Calibration 2012/05/24 2012/11/23 Broadband Amplifier JS4-00101800-35-5P 896037 Miteq 30MHz-18GHz Path Calibration 2012/05/24 2012/11/23 Cable "ESI to EMI EcoFlex10 W18.01-2+W38.01- Kabel Kusch Antenna" 2 Path Calibration 2012/05/24 2012/11/23 Cable "ESI to Horn UFB311A+UFB293C W18.02-2+W38.02- Rosenberger Micro-Coax Antenna" 2 Path Calibration 2012/05/24 2012/11/23 Path Calibration 2012/05/24 2012/11/23 Double-ridged horn HF 906 357357/001 Rohde & Schwarz GmbH & Co. KG Standard Calibration 2012/05/18 2015/05/17 Double-ridged horn HF 906 357357/002 Rohde & Schwarz GmbH & Co. KG Standard Calibration 2012/06/26 2015/06/25 High Pass Filter 4HC1600/12750-1.5-KK 9942011 Trilithic Path Calibration 2012/05/24 2012/11/23 High Pass Filter 5HC2700/12750-1.5-KK 9942012 Trilithic Path Calibration 2012/05/24 2012/11/23 High Pass Filter 5HC3500/12750-1.2-KK 200035008 Trilithic Path Calibration 2012/05/24 2012/11/23 High Pass Filter WHKX 7.0/18G-8SS 09 Wainwright Path Calibration 2012/05/24 2012/11/23 Horn Antenna BBHA 9170 Schwarzbeck 15-26 GHz BBHA 9170 Log.-per. Antenna HL 562 Ultralog 830547/003 Rohde & Schwarz GmbH & Co. KG Loop Antenna HFH2-Z2 829324/006 Rohde & Schwarz GmbH & Co. KG Standard calibration 2011/10/27 2014/10/26 Pyramidal Horn Antenna 3160-09 00083069 EMCO Elektronik GmbH 26,5 GHz Pyramidal Horn Antenna 3160-10 00086675 EMCO Elektronik GmbH 40 GHz Test report reference: MDE_ECOM_1202_FCCb Page 18 of 32

Single Devices for Auxiliary Equipment for Radiated emissions (continued) Single Device Name Type Serial Number Manufacturer Tilt device Maturo Antrieb TD1.5-10kg TD1.5- Maturo GmbH (Rohacell) 10kg/024/3790709 Test Equipment Auxiliary Test Equipment Lab ID: Lab 3, Lab 4 Manufacturer: see single devices Description: Single Devices for various Test Equipment Type: various Serial Number: none Single Devices for Auxiliary Test Equipment Single Device Name Type Serial Number Manufacturer AC Power Source Chroma 6404 64040001304 Chroma ATE INC. Broadband Power Divider 1506A / 93459 LM390 Weinschel Associates N (Aux) Broadband Power Divider WA1515 A855 Weinschel Associates SMA Digital Multimeter 03 Fluke 177 86670383 Fluke Europe B.V. (Multimeter) Customized calibration 2011/10/19 2013/10/18 Fibre optic link Satellite FO RS232 Link 181-018 Pontis (Aux) Fibre optic link FO RS232 Link 182-018 Pontis Transceiver (Aux) Isolating Transformer LTS 604 1888 Thalheimer Transformatorenwerke GmbH Notch Filter Ultra Stable WRCA800/960-6EEK 24 Wainwright (Aux) Vector Signal Generator SMIQ 03B 832492/061 Rohde & Schwarz GmbH & Co.KG Test report reference: MDE_ECOM_1202_FCCb Page 19 of 32

Test Equipment Digital Signalling Devices Lab ID: Lab 1, Lab 3, Lab 4 Description: Signalling equipment for various wireless technologies. Single Devices for Digital Signalling Devices Single Device Name Type Serial Number Manufacturer Bluetooth Signalling Unit CBT 100589 Rohde & Schwarz GmbH & Co. CBT KG Standard calibration 2011/11/24 2014/11/23 CMW500 CMW500 107500 Rohde & Schwarz GmbH & Co.KG Calibration Details Last Execution Next Exec. Initial factory calibration 2012/01/26 2014/01/25 Universal Radio CMU 200 102366 Rohde & Schwarz GmbH & Co. Communication Tester KG Standard calibration 2011/05/26 2013/05/25 HW/SW Status Date of Start Date of End Hardware: 2007/07/16 B11, B21V14, B21-2, B41, B52V14, B52-2, B53-2, B56V14, B68 3v04, PCMCIA, U65V04 Software: K21 4v21, K22 4v21, K23 4v21, K24 4v21, K42 4v21, K43 4v21, K53 4v21, K56 4v22, K57 4v22, K58 4v22, K59 4v22, K61 4v22, K62 4v22, K63 4v22, K64 4v22, K65 4v22, K66 4v22, K67 4v22, K68 4v22, K69 4v22 Firmware: µP1 8v50 02.05.06 --- Universal Radio CMU 200 837983/052 Rohde & Schwarz GmbH & Co. Communication Tester KG Standard calibration 2011/12/07 2014/12/06 HW/SW Status Date of Start Date of End HW options: 2007/01/02 B11, B21V14, B21-2, B41, B52V14, B52-2, B53-2, B54V14, B56V14, B68 3v04, B95, PCMCIA, U65V02 SW options: K21 4v11, K22 4v11, K23 4v11, K24 4v11, K27 4v10, K28 4v10, K42 4v11, K43 4v11, K53 4v10, K65 4v10, K66 4v10, K68 4v10, Firmware: µP1 8v40 01.12.05 --- SW: 2008/11/03 K62, K69 Test report reference: MDE_ECOM_1202_FCCb Page 20 of 32

Test Equipment Emission measurement devices Lab ID: Lab 1, Lab 3 Description: Equipment for emission measurements Serial Number: see single devices Single Devices for Emission measurement devices Single Device Name Type Serial Number Manufacturer Personal Computer Dell 30304832059 Dell Power Meter NRVD 828110/016 Rohde & Schwarz GmbH & Co.KG Calibration Details Last Execution Next Exec. Standard calibration 2012/05/22 2013/05/21 Power Sensor NRV-Z1 836219/005 Rohde & Schwarz GmbH & Co. KG Powermeter NRVS 836333/064 Rohde & Schwarz GmbH & Co. KG Sensor Head A NRV-Z1 827753/005 Rohde & Schwarz GmbH & Co.KG Calibration Details Last Execution Next Exec. Standard calibration 2012/05/21 2013/05/20 Signal Generator SMR 20 846834/008 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. standard calibration 2011/05/12 2014/05/11 Spectrum Analyzer ESIB 26 830482/004 Rohde & Schwarz GmbH & Co. KG Standard Calibration 2011/12/05 2013/12/04 HW/SW Status Date of Start Date of End Firmware-Update 4.34.4 from 3.45 during calibration 2009/12/03 Test report reference: MDE_ECOM_1202_FCCb Page 21 of 32

Test Equipment Radio Lab Test Equipment Lab ID: Lab 4 Description: Radio Lab Test Equipment Single Devices for Radio Lab Test Equipment Single Device Name Type Serial Number Manufacturer Broadband Power Divider WA1515 A856 Weinschel Associates SMA Coax Attenuator 10dB 4T-10 F9401 Weinschel Associates SMA 2W Coax Attenuator 10dB 56-10 W3702 Weinschel Associates SMA 2W Coax Attenuator 10dB 56-10 W3711 Weinschel Associates SMA 2W Coax Cable Sucotest 2,0m Rosenberger Micro-Coax Huber&Suhner Coax Cable Rosenberger FA210A0010003030 54491-2 Rosenberger Micro-Coax Micro Coax FA210A0010003030 SMA/SMA 1,0m Power Meter NRVD 828110/016 Rohde & Schwarz GmbH & Co.KG Calibration Details Last Execution Next Exec. Standard calibration 2012/05/22 2013/05/21 Power Sensor NRV-Z1 836219/005 Rohde & Schwarz GmbH & Co. KG Powermeter NRVS 836333/064 Rohde & Schwarz GmbH & Co. KG RF Step Attenuator RSP RSP 833695/001 Rohde & Schwarz GmbH & Co.KG Rubidium Frequency Datum, Model: MFL 2689/001 Datum-Beverly Standard Standard calibration 2012/06/21 2013/06/20 Sensor Head A NRV-Z1 827753/005 Rohde & Schwarz GmbH & Co.KG Calibration Details Last Execution Next Exec. Standard calibration 2012/05/21 2013/05/20 Signal Generator SMY02 829309/018 Rohde & Schwarz GmbH & Co. KG Standard calibration 2011/11/04 2014/11/03 Signal Generator SME SME03 827460/016 Rohde & Schwarz GmbH & Co.KG Standard calibration 2011/11/25 2014/11/24 Signal Generator SMP SMP02 836402/008 Rohde & Schwarz GmbH & Co. KG Spectrum Analyser FSIQ26 840061/005 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard calibration 2011/02/10 2013/02/09 Temperature Chamber VT 4002 58566002150010 Vötsch Vötsch 03 Calibration Details Last Execution Next Exec. Customized calibration 2012/03/12 2014/03/11 Test report reference: MDE_ECOM_1202_FCCb Page 22 of 32

Single Devices for Radio Lab Test Equipment (continued) Single Device Name Type Serial Number Manufacturer Vector Signal Generator SMIQ 03B 837747/020 Rohde & Schwarz GmbH & Co. KG Test Equipment Shielded Room 02 Lab ID: Lab 1 Manufacturer: Frankonia Description: Shielded Room for conducted testing Type: 12 qm Serial Number: none Test report reference: MDE_ECOM_1202_FCCb Page 23 of 32

5 Photo Report Photos are included in an external report. 6 Setup Drawings Drawing 1: Setup in the Anechoic chamber. For measurements below 1 GHz the ground was replaced by a conducting ground plane. Test report reference: MDE_ECOM_1202_FCCb Page 24 of 32

7 Annex measurement plots 7.1 Radiated emissions and peak output power 7.1.1 Spurious radiated emissions up to 30 MHz – Op-Mode 1 Antenna position 90° EUT position horizontal Marker: 125.3 kHz 47.3 dBµV/m X Level [dBµV/m] 110 100 80 60 40 20 10 9k 20k 40k 100k 300k 1M 2M 4M 10M 30M Frequency [Hz] MES ECO_1202_079_pre PK LIM H-Field_FCC209_10m Test report reference: MDE_ECOM_1202_FCCb Page 25 of 32

7.1.2 Spurious radiated emissions up to 30 MHz – Op-Mode 2 Antenna position 90° EUT position horizontal Marker: 133.7 kHz 47.61 dBµV/m X Level [dBµV/m] 110 100 80 60 40 20 0 9k 20k 40k 100k 300k 1M 2M 4M 10M 30M Frequency [Hz] MES ECO_1202_083_pre PK LIM H-Field_FCC209_10m Test report reference: MDE_ECOM_1202_FCCb Page 26 of 32

7.1.3 Spurious radiated emissions up to 30 MHz – Op-Mode 3 Antenna position 90° EUT position horizontal Marker: 128.2 kHz 70.28 dBµV/m X Level [dBµV/m] 110 100 80 60 40 20 10 9k 20k 40k 100k 300k 1M 2M 4M 10M 30M Frequency [Hz] MES ECO_1202_138_pre PK LIM H-Field_FCC209_10m Test report reference: MDE_ECOM_1202_FCCb Page 27 of 32

7.1.4 Spurious radiated emissions above 30 MHz – Op_Mode 1 Level [dBµV/m] 80 70 60 50 40 30 20 10 0 30M 50M 70M 100M 200M 300M 500M 700M 1G Frequency [Hz] MES ECO_1202_069_pre PK LIM FCC part 15 b Field Strength QP Limit Test report reference: MDE_ECOM_1202_FCCb Page 28 of 32

7.1.5 Spurious radiated emissions above 30 MHz – Op-Mode 2 Note: Peak at 900 MHz is an external GSM interferer Level [dBµV/m] 80 70 60 50 40 30 20 10 0 30M 50M 70M 100M 200M 300M 500M 700M 1G Frequency [Hz] MES ECO_1202_070_pre PK LIM FCC part 15 b Field Strength QP Limit Test report reference: MDE_ECOM_1202_FCCb Page 29 of 32

7.1.6 Spurious radiated emissions above 30 MHz – Op-Mode 3 Marker: 115.8 MHz 17.41 dBµV/m Level [dBµV/m] 60 50 40 30 20 10 0 30M 50M 70M 100M 200M 300M 500M 700M 1G Frequency [Hz] MES ECO_1202_141_pre PK LIM FCC part 15 b Field Strength QP Limit Test report reference: MDE_ECOM_1202_FCCb Page 30 of 32

7.2 AC Mains conducted 7.2.1 RFID 125 kHz conducted emissions (AC power line) Short Description: FCC Voltage 120 V 60 Hz Start Stop Step Detector Meas. IF Transducer Frequency Frequency Width Time Bandw. 150.0 kHz 30.0 MHz 5.0 kHz MaxPeak 20.0 ms 9 kHz ESH3-Z5 Average Level [dBµV] 80 70 60 50 40 + 30 20 10 0 150k 300k 500k 1M 2M 3M 5M 7M 10M 30M Frequency [Hz] + MES ECO_1202_119_fin AV MES ECO_1202_119_pre PK MES ECO_1202_119_pre AV LIM FCC 15b QP volt Voltage QP Limit LIM FCC 15b AV volt Voltage QP Limit Test report reference: MDE_ECOM_1202_FCCb Page 31 of 32

7.2.2 RFID 134 kHz conducted emissions (AC power line) Short Description: FCC Voltage 120 V 60 Hz Start Stop Step Detector Meas. IF Transducer Frequency Frequency Width Time Bandw. 150.0 kHz 30.0 MHz 5.0 kHz MaxPeak 20.0 ms 9 kHz ESH3-Z5 Average Level [dBµV] 80 70 60 50 40 30 20 10 + 0 150k 300k 500k 1M 2M 3M 5M 7M 10M 30M Frequency [Hz] + MES ECO_1202_120_fin AV MES ECO_1202_120_pre PK MES ECO_1202_120_pre AV LIM FCC 15b QP volt Voltage QP Limit LIM FCC 15b AV volt Voltage QP Limit Test report reference: MDE_ECOM_1202_FCCb Page 32 of 32


Document Created: 2013-04-04 13:05:57
Document Modified: 2013-04-04 13:05:57
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC