GOM-1307-3034-TEU311S-V01 4 of 5 SAR validation report 1

FCC ID: XAM300011GR02

RF Exposure Info

Download: PDF
FCCID_2121131

DASY5 Validation Report for Head TSL Date: 20.09.2012 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 1800 MHz; Type: D1800V2; Serial: D1800V2 — SN: 20046 Communication System: CW; Frequency: 1800 MHz Medium parameters used: f= 1800 MHz; 0 = 1.39 mho/m; & = 39.7; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C€63.19—2007) DASY52 Configuration: Probe: ES3DV3 — SN3205; ConvF(5.07, 5.07, 5.07); Calibrated: 30.12.2011; Sensor—Surface: 3mm (Mechanical Surface Detection) s Electronics: DAEA4 Sn601; Calibrated: 27.06.2012 * Phantom: Flat Phantom 5.0 (front); Type: QDOOOP5OAA; Serial: 1001 + DASY32 52.8.2(969); SEMCAD X 14.6.6(6824) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5tmm, dy=5mm, dz=5mm Reference Value = 94.360 V/m; Power Drift = 0.05 dB Peak SAR (extrapolated) = 16,297 mW/g SAR(I g) = 9.23 mW/g; SAR(10 g) = 4.89 mW/g Maximum value of SAR (measured) = 11.3 W/kg M 7.20 —10.00 §14.40 E—18.00 & 0 dB = 11.3 W/kg =21.06 dB W/kg Certificate No: D1800V2—2d046_Sep12 Page 5 of 8 ruge se yc ces

Impedance Measurement Plot for Head TSL 20 Sep 2012 14113114 [CHI sit 1 U F8 @47.042 4 —84955e 25.797 pF 1 800.000 Go NHz em=po=~ De1 Cor fivg 16 H1d CH2 Cor fiv 16° HLd START 1 550,.000 000 MHz STOP 2 000.000 0bd MHz Certificate No: D1800V2—24046_Sep12 Page 6 of 8 ruge ye es

DASY5 Validation Report for Body TSL Date: 24.09.2012 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 1800 MHz; Type: D1800V2; Serial: D1800V2 — SN: 24046 Communication System: CW; Frequency: 1800 MHz Medium parameters used: f = 1800 MHz; 0 = 1.53 mho/m; & = 51.7; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASYS5 (IEEE/IEC/ANSI €C63.19—2007) DASY52 Configuration: & Probe: ES3DV3 — SN3205; ConvF(4.74, 4.74, 4.74); Calibrated: 30.12.2011; Sensor—Surface: 3mm (Mechanical Surface Detection) Electronics: DAE4 $n601; Calibrated: 27.06.2012 Phantom: Flat Phantom 5.0 (back); Type: QDOOOP50AA; Serial: 1002 DASY52 52.8.2(969); SEMCAD X 14.6.6(6824) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 94.360 V/m; Power Drift = 0.05 dB Peak SAR (extrapolated) = 17.202 mW/g SAR(I g) = 9.75 mW/g; SAR(10 g) = 5.17 mW/g Maximum value of SAR (measured) = 12.3 W/kg ~7.20 0s —14.40 —18.00 3 0 dB = 12.3 W/kg = 21.80 dB W/kg Certificate No: D1800V2—2d046_Sep12 Page 7 of 8

Impedance Measurement Plot for Body TSL 24 Sep 2012 14150144 CHI si4 1 U Fs 244.9224 —2f656 6 31.974 pF 1 800.000 000 MHz e o. Del Cor Avg 16 HL d CH2 Cor fig 16° H1d START 1 550.000 000 MHz STOP 2 000.000 080 MHz Certificate No: D1800V2—24046_Sep12 Page 8 of 8 cuge ve ve s

Calibration Laboratory of Schwelzerischer Kalibrierdienst Schmid & Partner Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Client Eurofins Cértificate No: D1T90OV2—5d025_Sep12 ICALIBRATION CERTIFICATE Object D1900V2 — SN: 50025 Calibration procedure(s) QA CAL—05.v8 Calibration procedure for dipole validationkits above 700 MHz Calibration date: September 21, 2012 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 8)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter EPM~442A GB37480704 05—Oct—11 (No. 217—01451) Oct—12 Power sensor HP 8481A US37202783 05—Oct—11 (No. 217—01451) Oct—12 Reference 20 dB Attenuator SN: 5058 (20k) 27—Mar—12 (No. 217—01530) Apr—18 Type—N mismatch combination SN: 5047.2 / 06827 27—Mar—12 (No. 217—01538) Apr—13 Reference Probe ESSDV3 SN: 3205 80—Dec—11 (No. ES3—3205_Dec11) Dec—12 DAE4 SN: 601 27—Jun—12 (No. DAE4—601_Jun12) Jun—13 Secondary Standards ID # Check Date (in house) Scheduled Check Power sensor HP 8481A MY41092317 18—Oct—02 (in house check Oct—11) In house check: Oct—13 RF generator R&S SMT—06 100005 04—Aug—99 (in house check Oct—11) In house check: Oct—13 Network Analyzer HP 8758E US37390585 84206 18—Oct—01 (in house check Oct—11) In house check: Oct—12 Name Function Signature Calibrated by: Israe El—Naouq Laboratory Technician € (ngcww( Approved by: Katia Pokovic Technical Manager e Issued: September 21, 2012 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: D1900V2—54025_Sep12 Page 1 of 8 ruage es yc k8

a & Calibration Laboratory of w90 s\o\“\vy'/,,, Schweizerischer Kalibrierdienst Schmid & Partner iB\E—éMgE Service suisse d‘étalonnage Engineering AG 2 eR Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland ‘rx,@@ Swiss Calibration Service Wlalabs® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x.y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2003, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", December 2003 b) IEC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz)", February 2005 Federal Communications Commission Office of Engineering & Technology (FCC OET), "Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields; Additional Information for Evaluating Compliance of Mobile and Portable Devices with FCC Limits for Human Exposure to Radiofrequency Emissions", Supplement C (Edition 01—01) to Bulletin 65 Additional Documentation: d) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. Electrical Defay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported unceitainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D1900V2—54025_Sep12 Page 2 of 8 rouage revive ces

Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY5 V52.8.2 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 1900 MHz # 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 40.0 140 mho/m Measured Head TSL parameters (22.0 £0.2) °C 40.6 + 6 % 1.37 mho/m 6 % Head TSL temperature change during test <0.5 °C SAR result with Head TSL SAR averaged over 1 em* (1 g) of Head TSL Condition SAR measured 250 mW input power 9.78 mW / g SAR for nominal Head TSL parameters normalized to 1W 39.8 mW /g a 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 250 mW input power 5.17 mW /g SAR for nominal Head TSL parameters normalized to 1W 20.9 mW /g + 16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 53.3 1.52 mho/m Measured Body TSL parameters (22.0 £ 0.2) °C 52.5 +6 % 1.54 mho/m x 6 % Body TSL temperature change during test <0.5 °C ——— ~—— SAR result with Body TSL SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 250 mW input power 10.2 mW /g SAR for nominal Body TSL parameters normalized to 1W 40.3 mW / g + 17.0 % (k=2) SAR averaged over 10 cm* {10 g) of Body TSL condition SAR measured 250 mW input power 5.42 mW /g SAR for nominal Body TSL parameters normalized to 1W 21.5 mW / g £ 16.5 % (k=2) Certificate No: D1900V2—50025_Sep12 Page 3 of 8 rouage rv c y ces

Appendix Antenna Parameters with Head TSL Impedance, transformed to feed point 51.0 Q + 4.7 jQ Return Loss —26.5 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 47.3 Q + 5.1 jQ Return Loss —24.6 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.198 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on July 29, 2002 Certificate No: D1900V2—54025_Sep12 Page 4 of 8

DASY5 Validation Report for Head TSL Date: 21.09.2012 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 1900 MHz; Type: D1900V2; Serial: D1900V2 — SN: 50025 Communication System: CW; Frequency: 1900 MHz Medium parameters used: f= 1900 MHz; 0 = 1.37 mho/m; & = 40.6; p = 1000 kg/m" Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2007) DASY52 Configuration: e Probe: ES3DV3 — SN3205; ConvF(5.01, 5.01, 5.01); Calibrated: 30.12.2011; Sensor—Surface: 3mm (Mechanical Surface Detection) Electronics: DAFB4 $n601; Calibrated: 27.06.2012 Phantom: Flat Phantom 5.0 (front); Type: QDOOOP50AA; Serial: 1001 DASY52 52.8.2(969); SEMCAD X 14.6.6(6824) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 94.699 ¥/m; Power Drift = 0.03 dB Peak SAR (extrapolated) = 17.364 mW/g SAR(1 g) = 9.78 mW/g; SAR(10 g) = 5.17 mW/g Maximum value of SAR (measured) = 11.9 W/kg —8.00 $—12.00 16.00 20,00 0 dB = 11.9 W/kg = 21.51 dB W/kg Certificate No: D1900V2—5d025_Sep12 Page 5 of 8 rouage rev ve ces

Impedance Measurement Plot for Head TSL 21 Sep 2012 11155145 {CHI s11 1 U FS 4: 50.971 A 4.6563 2 390.03 pH 1 900.000 000 MHz ceg. Del Cor Avg 16 H1d CH2 Cor fiy 16°" H1d START 1 700.000 008 MHz STOP 2 150.000 000 MHz Certificate No: D1900V2—5d025_Sep12 Page 6 of 8 rug~ >

DASY5 Validation Report for Body TSL Date: 21.09.2012 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 1900 MHz; Type: D1900V2; Serial: DL900V2 — SN: 54025 Communication System: CW; Frequency: 1900 MHz Medium parameters used: f = 1900 MHz; 0 = 1.54 mho/m; &, = 52.5; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASYS (IEEE/IEC/ANSI C63.19—2007) DASY52 Configuration: * Probe: ES3DV3 — SN3205; ConvF(4.62, 4.62, 4.62); Calibrated: 30.12.2011; Sensor—Surface: 3mm (Mechanical Surface Detection) Electronics: DAE4 S$n601; Calibrated: 27.06.2012 Phantom: Flat Phantom 5.0 (back); Type: QDOOOP50AA; Serial: 1002 DASY52 52.8.2(969); SEMCAD X 14.6.6(6824) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 94.699 V/m; Power Drift = 0.07 dB Peak SAR (extrapolated) = 17.830 mW/g SAR(I g) = 10.2 mW/g; SAR(10 g) = 5.42 mW/g Maximum value of SAR (measured) = 12.8 W/kg j —12.00 B —16.00 —20.00 0 dB = 12.8 W/kg = 22.14 dB W/ikg Certificate No: D1900V2—5d025_Sep12 Page 7 of 8 rouage rev ve ces

Impedance Measurement Plot for Body TSL 21 Sep 2012 11155120 CHI) s11 1 L OFs 4t 47.297 a 5.05664 4 424.39 pH 1 900.000 0BB MHz [ormantl "~—_. Del Cor Ave 16 H1d CH2 Cor frg 16" H1d START 1 700.000 000 MHz STOP 2 150.000 000 MHz Certificate No: D1900V2—54025_Sep12 Page 8 of 8

Calibration Laboratory of NCz2* SA Schweizerischer Kalibrierdienst $ Schmid & Partner ila\ei\—ém Service suisse d‘étalonnage Engineering AG T s Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland * ?/\\\\3 Swiss Calibration Service alsitidet® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Client Eurofins Certificate No: D2450V2—722_Sep12 ICALIBRATION CERTIFICATE Object D2450V2 — SN: 722 Calibration procedure(s) QA CAL—05.v8 Calibration procedure for dipole validation kits above 700 MHz Calibration date: September 13, 2012 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1) The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratoryfacility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter EPM—~442A GB37480704 O5—Oct—11 (No. 217—01451) Oct12 Power sensor HP 8481A US37202783 05—Oct—11 (No. 217—01451) Oct—12 Reference 20 dB Attenuator SN: 5058 (20k) 27—Mar—12 (No. 217—01530) Apr—18 Type—N mismatch combination SN: 5047.2 / 06327 27—Mar—12 (No. 217—01538) Apr—13 Reference Probe ESSDV3 SN: 3205 30—Dec—11 (No. ES3—8205_Dec11) Dec—12 DAE4 SN: 601 27—Jun—12 (No. DAE4—601_Jun12) Jun—18 Secondary Standards ID # Check Date (in house) Scheduied Check Power sensor HP 8481A MY41092317 18—Oct—02 (in house check Oct—11) In house check: Oct—13 RF generator R&S SMT—06 100005 04—Aug—99 (in house check Oct—11) In house check: Oct—13 Network Analyzer HP 8753E US87390585 84206 18—Oct—01 (in house check Oct—11) In house check: Oct—12 Name Function Signature Calibrated by: Jeton Kastrati Laboratory Technician Lo Approved by: Katia Pokovie Technical Manager Tea4Z Issued: September 13, 2012 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: D2450V2—722_Sep12. Page 1 of 8 Puge ive vravs

Calibration Laboratory of ailys, Schweizerischer Kalibrierdienst Schmid & Partner ili‘\\k—//sl!l&/—;: Service suisse d‘étalonnage Engineering AG Z //—_\\ < Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland 4,,[[/Q\\§3 Swiss Calibration Service Uhilubt Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvrF sensitivity in TSL / NORM x,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) [EEE Std 1528—2003, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", December 2003 b) IEC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz)", February 2005 Federal Communications Commission Office of Engineering & Technology (FCC OET), "Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields; Additional Information for Evaluating Compliance of Mobile and Portable Devices with FCC Limits for Human Exposure to Radiofrequency Emissions", Supplement C (Edition 01—01) to Bulletin 65 Additional Documentation: d) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D2450V2—722_Sep12 Page 2 of 8 ugs rvervr rug

Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY5 V52.8.2 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantomn Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 2450 MHz + 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nomina!l Head TSL parameters 22.0 °C 39.2 1.80 mho/m Measured Head TSL parameters (22.0 x 0.2) °C 39.9 + 6 % 1.84 mho/m # 6 % Head TSL temperature change during test <0.5 °C SAR result with Head TSL SAR averaged over 1 em‘ (1 g) of Head TSL Condition SAR measured 250 mW input power 13.2 mW /g SAR for nominal Head TSL parameters normalized to 1W §2.5 mW /g a 17.0 % (k=2) SAR averaged over 10 cm‘ (10 g) of Head TSL condition SAR measured 250 mW input power 6.14 mW /g SAR for nominal Head TSL parameters normalized to 1 W 24.5 mW /g # 16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 52.7 1.95 mho/m Measured Body TSL parameters (22.0 £0.2) °C 51.0 + 6 % 2.01 mho/m + 6 % Body TSL temperature change during test <0.5 °C «=— ~~— SAR result with Body TSL SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 250 mW input power 12.9 mW /g SAR for nominal Body TSL parameters normalized to 1W 50.5 mW / g x 17.0 % (k=2) SAR averaged over 10 cm‘ (10 g) of Body TSL condition SAR measured 250 mW input power 6.03 mW / g SAR for nominal Body TSL parameters normalized to 1W 23.8 mW / g x 16.5 %(k=2) Certificate No: D2450V2—722_Sep12 Page 3 of 8 6ugw ryw urdus

Appendix Antenna Parameters with Head TSL Impedance, transformed to feed point 52.3 Q + 7.6 jQ Return Loss —22.2 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 48.8 Q + 8.4 jQ Return Loss —21.3 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.152 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on October 16, 2002 Certificate No: D2450V2—722_Sep12 Page 4 of 8 | uge rrv vravs

DASY5 Validation Report for Head TSL Date: 13.09.2012 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 722 Communication System: CW; Frequency: 2450 MHz Medium parameters used: £ = 2450 MHz; a = 1.84 mho/m; & = 39.9; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2007) DASY32 Configuration: Probe: ES3DV3 — SN3205; ConvF(4.45, 4.45, 4.45); Calibrated: 30.12.2011; Sensor—Surface: 3mm (Mechanical Surface Detection) Electronics: DAEA4 $n601; Calibrated: 27.06.2012 Phantom: Flat Phantom 5.0 (front); Type: QDOOOP50AA; Serial: 1001 DASY52 52.8.2(969); SEMCAD X 14.6.6(6824) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 98.454 V/m; Power Drift = 0.03 dB Peak SAR (extrapolated) = 27.064 mW/g SAR(I g) = 13.2 mW/g; SAR(10 g) = 6.14 mW/g Maximum value of SAR (measured) = 16.6 W/kg —6.00 d 12.00 P—ra.00 ~24.00 —30.00 0 dB = 16.6 W/kg = 24.40 dB W/kg Certificate No: D2450V2—722_Sep12 Page 5 of 8

Impedance Measurement Plot for Head TSL 43 Sep 2012 19123145 CHI sii 1 U oOFS 2 S2.B4d4 o 7.6426 a 495.47 pH 2450.000 obd MHz eP Del Ca fvg 16 H1Ld CH2 Ca fv 16" H1d START 2 250.000 coo MHz STOP 2 650.000 089 MHz Certificate No: D2450V2—722_Sep12 Page 6 of 8 6ugw rre vr us

DASY5 Validation Report for Body TSL Date: 13.09.2012 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 722 Communication System: CW; Frequency: 2450 MHz Medium parameters used: £ = 2450 MHz; o = 2.01 mho/m; s = 51; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASY5 (IERE/IEC/ANSI €63.19—2007) DASY52 Configuration: * Probe: ES3DV3 — SN3205; ConvF(4.26, 4.26, 4.26); Calibrated: 30.12.2011; e Sensor—Surface: 3mm (Mechanical Surface Detection) « Electronics: DAE4 Sn601; Calibrated: 27.06.2012 * Phantom: Flat Phantom 5.0 (back); Type: QDOOOP50AA; Serial: 1002 + DASY52 52.8.2(969); SEMCAD X 14.6.6(6824) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 94.538 V/m; Power Drift = 0.03 dB Peak SAR (extrapolated) = 26.530 mW/g SAR(I g) = 12.9 mW/g; SAR(10 g) = 6.03 mW/g Maximum value of SAR (measured) = 16.8 W/kg ~20.00 —25.00 0 dB = 16.8 W/kg = 24.51 dB W/kg Certificate No: D2450V2—722_Sep12 Page 7 of 8 rouage re ve ces

Impedance Measurement Plot for Body TSL 13 Sep 2012 10123:18 CHI s1 1 L OFS R48.765 n 84258 e §547.22 pH 2450.000 D0G MHz en —=po. l— De1 Ca fvg 16 H1d CH2 Ca fre 16° H1d START 2 250.000 000 MHz STOP 2 650.000 00B MHz Certificate No: D2450V2—722_Sep12 Page 8 of 8 | uge iz vr v.

Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner Sm Service suisse d‘étalonnage Engineering AG ilac=wRA Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Client Eurofins Certificate No: D5GHzV2—1140_Nov12 |CALIBRATION CERTIFICATE Object D5GHzV2 — SN: 1140 Calibration procedure(s) QA CAL—22.v1 Calibration procedure for dipole validation kits between 3—6 GHz Calibration date: November 13, 2012 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter EPM—442A GB37480704 O1—Nov—12 (No. 217—01640) Oct—13 Power sensor HP 8481A US37292783 O1—Nov—12 (No. 217—01640) Oct—13 Reference 20 dB Attenuator SN: 5058 (20k) 27—Mar—12 (No. 217—01530) Apr—13 Type—N mismatch combination SN: 5047.2 / 06327 27—Mar—12 (No. 217—01533) Apr—13 Reference Probe EX8DV4 SN: 3503 30—Dec—11 (No. EX3—3503_Dec11) Dec—12 DAE4 SN: 601 27—Jun—12 (No. DAE4—601_Jun12) Jun—13 Secondary Standards ID # Check Date (in house) Scheduled Check Power sensor HP 8481A MY41092317 18—Oct—02 (in house check Oct—11) In house check: Oct—13 RF generator R&S SMT—06 100005 04—Aug—99 (in house check Oct—11) In house check: Oct—13 Network Analyzer HP 8753E US37390585 $4206 18—Oct—01 (in house check Oct—12) In house check: Oct—13 Name Function Signature Calibrated by: Leif Klysner Laboratory Technician W% Approved by: Katia Pokovic Technical Manager /K4 Issued: November 13, 2012 This calibration certificate shall not be reproduced exceptin full without written approvalof the laboratory. Certificate No: D5GHzV2—1140_Nov12 Page 1 of 13

Calibration Laboratory of any% S\ Schweizerischer Kalibrierdienst ; & gAZ % Schmid & Partner SB\EU_%& Service suisse d‘étalonnage Engmeering AG raig Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland 4«/,[ I//—\\\ \\\P Swiss Calibration Service t us Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x,.y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEC 62209—2, "Evaluation of Human Exposure to Radio Frequency Fields from Handheld and Body—Mounted Wireless Communication Devices in the Frequency Range of 30 MHz to 6 GHz: Human models, Instrumentation, and Procedures"; Part 2: "Procedure to determine the Specific Absorption Rate (SAR) for including accessories and multiple transmitters", March 2010 b) Federal Communications Commission Office of Engineering & Technology (FCC OET}, "Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields; Additional Information for Evaluating Compliance of Mobile and Portable Devices with FCC Limits for Human Exposure to Radiofrequency Emissions", Supplement C (Edition 01—01) to Bulletin 65 Additional Documentation: c) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: e Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. e Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. e Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. e Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. e SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D5GHzV2—1140_Nov12 Page 2 of 13 hounggas n e w w awes

Measurement Conditions DASY system configuration, as far as not iven on page 1. DASY Version DASY5 V52.8.3 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom V5.0 Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy = 4.0 mm, dz =1.4 mm Graded Ratio = 1.4 (Z direction) 5200 MHz + 1 MHz Frequency 5500 MHz + 1 MHz 5800 MHz + 1 MHz Head TSL parameters at 5200 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 36.0 4.66 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 34.8 + 6 % 4.53 mho/m + 6 % Head TSL temperature change during test <0.5 °C SAR result with Head TSL at 5200 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 7.99 W/kg SAR for nominal Head TSL parameters normalized to 1W 79.3 Wikg * 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.28 Wikg SAR for nominal Head TSL parameters normalized to 1W 22.6 Wikg + 19.5 % (k=2) Head TSL parameters at 5500 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.6 4.96 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 34.4 + 6 % 4.83 mho/m + 6 % Head TSL temperature change during test <0.5 °C ———— ~——— SAR result with Head TSL at 5500 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.46 W/kg SAR for nominal Head TSL parameters normalized to 1W 83.9 W / kg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.40 Wikg SAR for nominal Head TSL parameters normalized to 1W 23.7 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1140_Nov12 Page 3 of 13 wgy en e ve ev

Head TSL parameters at 5800 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.0 5.27 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 34.0 + 6 % 5.15 mho/m + 6 % Head TSL temperature change during test <0.5 °C SAR result with Head TSL at 5800 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 7.83 W/kg SAR for nominal Head TSL parameters normalized to 1W 77.6 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.23 Wikg SAR for nominal Head TSL parameters normalized to 1W 22.1 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1140_Nov12 Page 4 of 13 uyy >

Body TSL parameters at 5200 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 49.0 5.30 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 46.8 + 6 % 5.35 mho/m + 6 % Body TSL temperature change during test <0.5 °C SAR result with Body TSL at 5200 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.42 W/kg SAR for nominal Body TSL parameters normalized to 1W 73.5 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.08 Wikg SAR for nominal Body TSL parameters normalized to 1W 20.6 Wikg + 19.5 % (k=2) Body TSL parameters at 5500 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.6 5.65 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 46.3 + 6 % 5.73 mho/m + 6 % Body TSL temperature change during test <0.5 °C SAR result with Body TSL at 5500 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.97 Wikg SAR for nominal Body TSL parameters normalized to 1W 79.0 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.22 Wikg SAR for nominal Body TSL parameters normalized to 1W 21.9 Wikg # 19.5 % (k=2) Certificate No: D5GHzV2—1140_Nov12 Page 5 of 13

Body TSL parameters at 5800 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.2 6.00 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 45.9 +6 % 6.13 mho/m + 6 % Body TSL temperature change during test 465°C SAR result with Body TSL at 5800 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 743 W/kg SAR for nominal Body TSL parameters normalized to 1W 73.6 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.07 Wikg SAR for nominal Body TSL parameters normalized to 1W 20.4 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1140_Nov12 Page 6 of 13

Appendix Antenna Parameters with Head TSL at 5200 MHz Impedance, transformed to feed point 48.6 Q — 7.5 jQ Return Loss —22.2 dB Antenna Parameters with Head TSL at 5500 MHz Impedance, transformed to feed point 53.3 Q — 0.6 jQ Return Loss —29.8 dB Antenna Parameters with Head TSL at 5800 MHz Impedance, transformed to feed point 56.6 Q — 1.8 jQ Return Loss —23.8 dB Antenna Parameters with Body TSL at 5200 MHz Impedance, transformed to feed point 48.6 Q — 6.9 jQ Return Loss — 22.9 dB Antenna Parameters with Body TSL at 5500 MHz Impedance, transformed to feed point 54.2 Q + 0.6 jQ Return Loss —27.7 dB Antenna Parameters with Body TSL at 5800 MHz Impedance, transformed to feed point 57.4 Q — 1.2 jQ Return Loss —23.1 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.202 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on May 07, 2012 Certificate No: D5GHzV2—1140_Nov12 Page 7 of 13 fouage cz c e ky

DASY5 Validation Report for Head TSL Date: 13.11.2012 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 5GHz; Type: DSGHzV2; Serial: D5GHzV2 — SN: 1140 Communication System: CW; Frequency: 5200 MHz, Frequency: 5500 MHz, Frequency: 5800 MHz Medium parameters used: f = 5200 MHz; 0 = 4.53 mho/m; &, = 34.8; p = 1000 kg/m3 , Medium parameters used: £= 5500 MHz; 0 = 4.83 mho/m; &= 34.4; p = 1000 kg/m3 , Medium parameters used: f = 5800 MHz; o = 5.15 mho/m; &, = 34; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI €63.19—2007) DASY52 Configuration: e Probe: EX3DV4 — SN3503; ConvF(5.41, 5.41, 5.41); Calibrated: 30.12.2011, ConvF(4.91, 4.91, 4.91); Calibrated: 30.12.2011, ConvF(4.81, 4.81, 4.81); Calibrated: 30.12.2011; e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 27.06.2012 & Phantom: Flat Phantom 5.0 (front); Type: QDOOOP5OAA; Serial: 1001 e DASY52 52.8.3(988); SEMCAD X 14.6.7(6848) Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5200 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 62.376 V/m; Power Drift = 0.04 dB Peak SAR (extrapolated) = 29.2 W/kg SAR(1 g) = 7.99 W/kg; SAR(10 g) = 2.28 W/kg Maximum value of SAR (measured) = 18.0 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5500 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 62.330 V/m; Power Drift = 0.04 dB Peak SAR (extrapolated) = 33.1 W/kg SAR(1 g) = 8.46 W/kg; SAR(10 g) = 2.4 W/kg Maximum value of SAR (measured) = 19.7 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5800 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 59.000 V/m; PowerDrift = 0.04 dB Peak SAR (extrapolated) = 32.2 W/kg SAR(1 g) =7.83 W/kg; SAR(10 g) = 2.23 W/kg Maximum value of SAR (measured) = 18.6 W/kg Certificate No: D5GHzV2—1140_Nov12 Page 8 of 13

—10.00 —20.00 —30.00 ~40.00 50.00 0 dB = 18.6 W/kg = 12.70 dBW/kg Certificate No: D5GHzV2—1140_Nov12 Page 9 of 13 fouge cee ve ces

Impedance Measurement Plot for Head TSL 13 Nov 2012 10:59:50 CHI sii 1 U FS 1: 48.566 a 5371 a 4.0608 pF 5 200.000 000 MHz 3——_ # CH1 Markers Del Jt §3.297 a ~625.00 m Cor 5.50000 GHz 5t 56,637 a —1.8105 a 5.90000 GHz Av 169 H1d CH2 CH2 Markers 3:—29.765 dB Cor 5.50000 GHz 5:—23.802 dB 5.90000 GHz Av 169 H1d START 5 000.000 900 MHz STOP 6 000.000 000 MHz Certificate No: D5GHzV2—1140_Nov12 Page 10 of 13

DASY5 Validation Report for Head TSL Date: 13.11.2012 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 5GHz; Type: DSGHzV2; Serial: D5GHzV2 — SN: 1140 Communication System: CW; Frequency: 5200 MHz, Frequency: 5500 MHz, Frequency: 5800 MHz Medium parameters used: f = 5200 MHz; 0 = 4.53 mho/m; &, = 34.8; p = 1000 kg/m3 , Medium parameters used: £= 5500 MHz; 0 = 4.83 mho/m; &= 34.4; p = 1000 kg/m3 , Medium parameters used: f = 5800 MHz; o = 5.15 mho/m; &, = 34; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI €63.19—2007) DASY52 Configuration: e Probe: EX3DV4 — SN3503; ConvF(5.41, 5.41, 5.41); Calibrated: 30.12.2011, ConvF(4.91, 4.91, 4.91); Calibrated: 30.12.2011, ConvF(4.81, 4.81, 4.81); Calibrated: 30.12.2011; e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 27.06.2012 & Phantom: Flat Phantom 5.0 (front); Type: QDOOOP5OAA; Serial: 1001 e DASY52 52.8.3(988); SEMCAD X 14.6.7(6848) Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5200 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 62.376 V/m; Power Drift = 0.04 dB Peak SAR (extrapolated) = 29.2 W/kg SAR(1 g) = 7.99 W/kg; SAR(10 g) = 2.28 W/kg Maximum value of SAR (measured) = 18.0 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5500 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 62.330 V/m; Power Drift = 0.04 dB Peak SAR (extrapolated) = 33.1 W/kg SAR(1 g) = 8.46 W/kg; SAR(10 g) = 2.4 W/kg Maximum value of SAR (measured) = 19.7 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5800 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 59.000 V/m; PowerDrift = 0.04 dB Peak SAR (extrapolated) = 32.2 W/kg SAR(1 g) =7.83 W/kg; SAR(10 g) = 2.23 W/kg Maximum value of SAR (measured) = 18.6 W/kg Certificate No: D5GHzV2—1140_Nov12 Page 8 of 13


Document Created: 2013-10-31 11:32:33
Document Modified: 2013-10-31 11:32:33
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC