Test reports

FCC ID: X4YHACSN4U1

Test Report

Download: PDF
FCCID_4421452

Shenzhen CTL Testing Technology Co., Ltd. Tel: +86-755-89486194 E-mail: ctl@ctl-lab.com TEST REPORT FCC PART 15.247 Report Reference No. ................. : CTL1906053014-WF Compiled by: Happy Guo ( position+printed name+signature) (File administrators) Tested by: Nice Nong ( position+printed name+signature) (Test Engineer) Approved by: Ivan Xie ( position+printed name+signature) (Manager) Product Name.............................. : Contact sensor Model/Type reference ................. : AHBSNMA4U1 WSD1001, WSD1131, WSD1128, WSD1221, WSD1286, List Model(s) ................................ : WSD1601, WSD1613 Trade Mark ................................... : Nexxt Solutions FCC ID .......................................... : X4YHACSN4U1 Applicant’s name ........................ : NEXXT SOLUTIONS Address of applicant .................. : 3505 N.W 107TH AVE. MIAMI Florida 33178 United States Test Firm ...................................... : Shenzhen CTL Testing Technology Co., Ltd. Floor 1-A, Baisha Technology Park, No.3011, Shahexi Road, Address of Test Firm .................. : Nanshan District, Shenzhen, China 518055 Test specification ........................ : Standard ........................................ : FCC Part 15.247: Operation within the bands 902-928 MHz, 2400-2483.5 MHz and 5725-5850 MHz. TRF Originator .............................. : Shenzhen CTL Testing Technology Co., Ltd. Master TRF ................................... : Dated 2011-01 Date of receipt of test item ......... : Jul. 10, 2019 Date of sampling ......................... : Jul. 10, 2019 Date of Test Date ......................... : Jul. 10, 2019–Jul. 30, 2019 Data of Issue ................................ : Aug. 02, 2019 Result ........................................... : Pass Shenzhen CTL Testing Technology Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen CTL Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen CTL Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context.

V1.0 Page 2 of 32 Report No.: CTL1906053014-WF TEST REPORT Aug. 02, 2019 Test Report No. : CTL1906053014-WF Date of issue Equipment under Test : Contact sensor Model /Type : AHBSNMA4U1 : WSD1001, WSD1131, WSD1128, WSD1221, Listed Models WSD1286, WSD1601, WSD1613 Applicant : NEXXT SOLUTIONS : 3505 N.W 107TH AVE. MIAMI Florida 33178 United Address States Manufacturer : SUNGALE ELECTRONICS (SHENZHEN) CO., LTD Address : No.1302, DaHong High-Tech Park, No. 6-18, XinHe Road, Xinqiao, Shajing, BaoAn, Shenzhen, 518105, China Test result Pass * * In the configuration tested, the EUT complied with the standards specified page 5. The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the issuing testing laboratory.

V1.0 Page 3 of 32 Report No.: CTL1906053014-WF ** Modified History ** Revisions Description Issued Data Report No. Remark Version 1.0 Initial Test Report Release 2019-08-02 CTL1906053014-WF Tracy Qi

V1.0 Page 4 of 32 Report No.: CTL1906053014-WF Table of Contents Page 1. SUMMARY............................................................................................................................................................ 5 1.1. TEST STANDARDS ..................................................................................................................................................... 5 1.2. TEST DESCRIPTION ........................................................................................................................................................ 5 1.3. TEST FACILITY .............................................................................................................................................................. 6 1.4. STATEMENT OF THE MEASUREMENT UNCERTAINTY ............................................................................................................... 6 2. GENERAL INFORMATION....................................................................................................................................... 8 2.1. ENVIRONMENTAL CONDITIONS ........................................................................................................................................ 8 2.2. GENERAL DESCRIPTION OF EUT ...................................................................................................................................... 8 2.3. DESCRIPTION OF TEST MODES AND TEST FREQUENCY .......................................................................................................... 8 2.4. EQUIPMENTS USED DURING THE TEST .............................................................................................................................. 9 2.5. RELATED SUBMITTAL(S) / GRANT (S) ................................................................................................................................ 9 2.6. MODIFICATIONS ........................................................................................................................................................... 9 3. TEST CONDITIONS AND RESULTS ......................................................................................................................... 10 3.1. CONDUCTED EMISSIONS TEST ....................................................................................................................................... 10 3.2. RADIATED EMISSIONS AND BAND EDGE .......................................................................................................................... 11 3.3. MAXIMUM CONDUCTED OUTPUT POWER....................................................................................................................... 18 3.4. POWER SPECTRAL DENSITY .......................................................................................................................................... 19 3.5. 6DB BANDWIDTH ....................................................................................................................................................... 21 3.6. OUT‐OF‐BAND EMISSIONS............................................................................................................................................ 23 3.7. ANTENNA REQUIREMENT ............................................................................................................................................. 27 4. TEST SETUP PHOTOS OF THE EUT ........................................................................................................................ 28 5. EXTERNAL AND INTERNAL PHOTOS OF THE EUT .................................................................................................. 29

V1.0 Page 5 of 32 Report No.: CTL1906053014-WF 1. SUMMARY 1.1. TEST STANDARDS The tests were performed according to following standards: FCC Rules Part 15.247: Frequency Hopping, Direct Spread Spectrum and Hybrid Systems that are in operation within the bands of 902-928 MHz, 2400-2483.5 MHz, and 5725-5850 MHz ANSI C63.10: 2013: American National Standard for Testing Unlicensed Wireless Devices KDB558074 D01 15.247 Meas Guidance v05r02: Guidance for Performing Compliance Measurements on Digital Transmission Systems (DTS) Operating Under §15.247 1.2. Test Description FCC PART 15.247 FCC Part 15.207 AC Power Conducted Emission N/A FCC Part 15.247(a)(2) 6dB Bandwidth PASS FCC Part 15.247(d) Spurious RF Conducted Emission PASS FCC Part 15.247(b) Maximum Conducted Output Power PASS FCC Part 15.247(e) Power Spectral Density PASS FCC Part 15.109/ 15.205/ 15.209 Radiated Emissions PASS FCC Part 15.247(d) Band Edge PASS FCC Part 15.203/15.247 (b) Antenna Requirement PASS

V1.0 Page 6 of 32 Report No.: CTL1906053014-WF 1.3. Test Facility 1.3.1 Address of the test laboratory Shenzhen CTL Testing Technology Co., Ltd. Floor 1-A, Baisha Technology Park, No. 3011, Shahexi Road, Nanshan, Shenzhen 518055 China There is one 3m semi-anechoic chamber and two line conducted labs for final test. The Test Sites meet the requirements in documents ANSI C63.4 and CISPR 32/EN 55032 requirements. 1.3.2 Laboratory accreditation The test facility is recognized, certified, or accredited by the following organizations: CNAS-Lab Code: L7497 Shenzhen CTL Testing Technology Co., Ltd. has been assessed and proved to be in compliance with CNAS-CL01 Accreditation Criteria for Testing and Calibration Laboratories (identical to ISO/IEC 17025: 2005 General Requirements) for the Competence of Testing and Calibration Laboratories. A2LA-Lab Cert. No. 4343.01 Shenzhen CTL Testing Technology Co., Ltd. EMC Laboratory has been accredited by A2LA for technical competence in the field of electrical testing, and proved to be in compliance with ISO/IEC 17025: 2005 General Requirements for the Competence of Testing and Calibration Laboratories and any additional program requirements in the identified field of testing. IC Registration No.: 9518B CAB identifier: CN0041 The 3m alternate test site of Shenzhen CTL Testing Technology Co., Ltd. EMC Laboratory has been registered by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements with Registration No.: 9518B on Jan. 22, 2019. FCC-Registration No.: 399832 Designation No.: CN1216 Shenzhen CTL Testing Technology Co., Ltd. EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration 399832, December 08, 2017. 1.4. Statement of the measurement uncertainty The data and results referenced in this document are true and accurate. The reader is cautioned that there may be errors within the calibration limits of the equipment and facilities. The measurement uncertainty was calculated for all measurements listed in this test report acc. to CISPR 16 - 4 “Specification for radio disturbance and immunity measuring apparatus and methods – Part 4: Uncertainty in EMC Measurements“ and is documented in the Shenzhen CTL Testing Technology Co., Ltd. quality system acc. to DIN EN ISO/IEC 17025. Furthermore, component and process variability of devices similar to that tested may result in additional deviation. The manufacturer has the sole responsibility of continued compliance of the device. Hereafter the best measurement capability for CTL laboratory is reported: Measurement Test Notes Uncertainty Transmitter power conducted ±0.57 dB (1) Transmitter power Radiated ±2.20 dB (1) Conducted spurious emission 9KHz-40 GHz ±2.20 dB (1) Occupied Bandwidth ±0.01ppm (1) Radiated Emission 30~1000MHz ±4.10dB (1) Radiated Emission Above 1GHz ±4.32dB (1)


V1.0 Page 8 of 32 Report No.: CTL1906053014-WF 2. GENERAL INFORMATION 2.1. Environmental conditions During the measurement the environmental conditions were within the listed ranges: Normal Temperature: 25°C Relative Humidity: 55 % Air Pressure: 101 kPa 2.2. General Description of EUT Product Name: Contact sensor Model/Type reference: AHBSNMA4U1 Power supply: DC 3.0V from battery Bluetooth LE Supported type: Bluetooth low Energy Modulation: GFSK Operation frequency: 2402MHz to 2480MHz Channel number: 40 Channel separation: 2 MHz Antenna type: PCB Antenna Antenna gain: 0dBi Note: For more details, please refer to the user’s manual of the EUT. 2.3. Description of Test Modes and Test Frequency The Applicant provides communication tools software to control the EUT for staying in continuous transmitting (Duty Cycle more than 98%) and receiving mode for testing. There are 39 channels provided to the EUT and Channel 00/19/39 were selected for BLE test. Operation Frequency List： Channel Frequency (MHz) 00 2402 02 2404 03 2406 ... ... 19 2440 ... ... 37 2476 38 2478 39 2480 Note: The line display in grey were the channel selected for testing

V1.0 Page 9 of 32 Report No.: CTL1906053014-WF 2.4. Equipments Used during the Test Calibration Calibration Test Equipment Manufacturer Model No. Serial No. Date Due Date 3560.6550.1 LISN R&S ENV216 2019/05/20 2020/05/19 2 LISN R&S ESH2-Z5 860014/010 2019/05/20 2020/05/19 Sunol Sciences Bilog Antenna JB1 A061713 2019/05/20 2020/05/19 Corp. EMI Test Receiver R&S ESCI 1166.5950.03 2019/05/20 2020/05/19 Spectrum Analyzer Agilent E4407B MY41440676 2019/05/20 2020/05/19 Spectrum Analyzer Agilent N9020 US46220290 2019/05/20 2020/05/19 Spectrum Analyzer Keysight N9020A MY53420874 2019/05/20 2020/05/19 Controller EM Electronics EM 1000 060859 2019/05/20 2020/05/19 Sunol Sciences Horn Antenna DRH-118 A062013 2019/05/20 2020/05/19 Corp. Active Loop Da Ze ZN30900A / 2019/05/20 2020/05/19 Antenna Amplifier Agilent 8449B 3008A02306 2019/05/20 2020/05/19 Amplifier Agilent 8447D 2944A10176 2019/05/20 2020/05/19 Temperature/Humi Gangxing CTH-608 02 2019/05/20 2020/05/19 dity Meter High-Pass Filter micro-tranics HPM50108 G174 2019/05/20 2020/05/19 High-Pass Filter micro-tranics HPM50111 G142 2019/05/20 2020/05/19 HUBER+SUHN SUCOFLEX 2019/05/20 2020/05/19 Coaxial Cables 10m ER 104PEA-10M HUBER+SUHN SUCOFLEX 2019/05/20 2020/05/19 Coaxial Cables 3m ER 104PEA-3M HUBER+SUHN SUCOFLEX 2019/05/20 2020/05/19 Coaxial Cables 3m ER 104PEA-3M RF Cable Megalon RF-A303 N/A 2019/05/20 2020/05/19 Power Sensor Agilent U2021XA MY5365004 2019/05/20 2020/05/19 Power Meter Agilent U2531A TW53323507 2019/05/20 2020/05/19 The calibration interval was one year 2.5. Related Submittal(s) / Grant (s) This submittal(s) (test report) is intended to comply with Section 15.247 of the FCC Part 15, Subpart C Rules. 2.6. Modifications No modifications were implemented to meet testing criteria.

V1.0 Page 10 of 32 Report No.: CTL1906053014-WF 3. TEST CONDITIONS AND RESULTS 3.1. Conducted Emissions Test LIMIT FCC CFR Title 47 Part 15 Subpart C Section 15.207 Limit (dBuV) Frequency range (MHz) Quasi-peak Average 0.15-0.5 66 to 56* 56 to 46* 0.5-5 56 46 5-30 60 50 * Decreases with the logarithm of the frequency. TEST CONFIGURATION TEST PROCEDURE 1. The equipment was set up as per the test configuration to simulate typical actual usage per the user’s manual. The EUT is a tabletop system; a wooden table with a height of 0.8 meters is used and is placed on the ground plane as per ANSI C63.10:2013. 2. Support equipment, if needed, was placed as per ANSI C63.10:2013. 3. All I/O cables were positioned to simulate typical actual usage as per ANSI C63.10:2013. 4. The adapter received AC120V/60Hz power through a Line Impedance Stabilization Network (LISN) which supplied power source and was grounded to the ground plane. 5. All support equipments received AC power from a second LISN, if any. 6. The EUT test program was started. Emissions were measured on each current carrying line of the EUT using a spectrum Analyzer / Receiver connected to the LISN powering the EUT. The LISN has two monitoring points: Line 1 (Hot Side) and Line 2 (Neutral Side). Two scans were taken: one with Line 1 connected to Analyzer / Receiver and Line 2 connected to a 50 ohm load; the second scan had Line 1 connected to a 50 ohm load and Line 2 connected to the Analyzer / Receiver. 7. Analyzer / Receiver scanned from 150 KHz to 30MHz for emissions in each of the test modes. 8. During the above scans, the emissions were maximized by cable manipulation. TEST RESULTS Not applicable to this device, which is powered by battery.

V1.0 Page 11 of 32 Report No.: CTL1906053014-WF 3.2. Radiated Emissions and Band Edge Limit For intentional device, according to § 15.209(a), the general requirement of field strength of radiated emission out of authorized band shall not exceed the following table at a 3 meters measurement distance. In addition, radiated emissions which fall in the restricted bands, as defined in §15.205(a), must also comply with the radiated emission limits specified in §15.209(a) Radiated emission limits Frequency (MHz) Distance (Meters) Radiated (dBμV/m) Radiated (μV/m) 0.009-0.49 3 20log(2400/F(KHz))+40log(300/3) 2400/F(KHz) 0.49-1.705 3 20log(24000/F(KHz))+ 40log(30/3) 24000/F(KHz) 1.705-30 3 20log(30)+ 40log(30/3) 30 30-88 3 40.0 100 88-216 3 43.5 150 216-960 3 46.0 200 Above 960 3 54.0 500 TEST CONFIGURATION (A) Radiated Emission Test Set-Up, Frequency Below 30MHz (B) Radiated Emission Test Set-Up, Frequency below 1000MHz (C) Radiated Emission Test Set-Up, Frequency above 1000MHz

V1.0 Page 12 of 32 Report No.: CTL1906053014-WF Test Procedure 1. Below 1GHz measurement the EUT is placed on a turntable which is 0.8m above ground plane, and above 1GHz measurement EUT was placed on a low permittivity and low loss tangent turn table which is 1.5m above ground plane. 2. Maximum procedure was performed by raising the receiving antenna from 1m to 4m and rotating the turn table from 0℃ to 360℃ to acquire the highest emissions from EUT 3. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 4. Repeat above procedures until all frequency measurements have been completed. TEST RESULTS Remark: 1. For below 1GHz testing recorded worst at BLE low channel. 2. Radiated emission test from 9 KHz to 10th harmonic of fundamental was verified, and no emission found except system noise floor in 9 KHz to 30MHz and not recorded in this report.

V1.0 Page 13 of 32 Report No.: CTL1906053014-WF For 30MHz-1GHz Horizontal Vertical

V1.0 Page 14 of 32 Report No.: CTL1906053014-WF For 1GHz to 25GHz BLE Mode (above 1GHz) Frequency(MHz): 2402 Polarity: HORIZONTAL Pre- Frequency Emission Limit Margin Raw Antenna Cable Correction amplifier (MHz) Level (dBuV/m) (dB) Value Factor Factor (dB) Factor (dBuV/m) (dBuV) (dB/m) (dB) (dB/m) 4804.00 51.24 PK 74.00 22.76 46.73 33.49 6.91 35.89 4.51 4804.00 -- AV 54.00 -- -- -- -- -- -- 5122.50 44.12 PK 74.00 29.88 36.91 34.38 7.10 34.27 7.21 5122.50 -- AV 54.00 -- -- -- -- -- -- 7206.00 46.34 PK 74.00 27.66 35.24 36.95 9.18 35.03 11.10 7206.00 -- AV 54.00 -- -- -- -- -- -- Frequency(MHz): 2402 Polarity: VERTICAL Pre- Frequency Emission Limit Margin Raw Antenna Cable Correction amplifier (MHz) Level (dBuV/m) (dB) Value Factor Factor (dB) Factor (dBuV/m) (dBuV) (dB/m) (dB) (dB/m) 4804.00 50.16 PK 74.00 23.84 45.65 33.49 6.91 35.89 4.51 4804.00 -- AV 54.00 -- -- -- -- -- -- 5122.50 44.01 PK 74.00 29.99 36.45 34.69 7.23 34.36 7.56 5122.50 -- AV 54.00 -- -- -- -- -- -- 7206.00 46.27 PK 74.00 27.73 35.17 36.95 9.18 35.03 11.10 7206.00 -- AV 54.00 -- -- -- -- -- -- Frequency(MHz): 2440 Polarity: HORIZONTAL Pre- Frequency Emission Limit Margin Raw Antenna Cable Correction amplifier (MHz) Level (dBuV/m) (dB) Value Factor Factor (dB) Factor (dBuV/m) (dBuV) (dB/m) (dB) (dB/m) 4880.00 49.36 PK 74.00 24.64 43.11 33.60 6.95 34.30 6.25 4880.00 -- AV 54.00 -- -- -- -- -- -- 5233.75 44.21 PK 74.00 29.79 36.58 34.57 7.16 34.10 7.63 5233.75 -- AV 54.00 -- -- -- -- -- -- 7320.00 46.39 PK 74.00 27.61 34.70 37.46 9.23 35.00 11.69 7320.00 -- AV 54.00 -- -- -- -- -- -- Frequency(MHz): 2440 Polarity: VERTICAL Pre- Frequency Emission Limit Margin Raw Antenna Cable Correction amplifier (MHz) Level (dBuV/m) (dB) Value Factor Factor (dB) Factor (dBuV/m) (dBuV) (dB/m) (dB) (dB/m) 4880.00 48.16 PK 74.00 25.84 41.91 33.60 6.95 34.30 6.25 4880.00 -- AV 54.00 -- -- -- -- -- -- 5233.75 44.19 PK 74.00 29.81 36.55 34.58 7.16 34.10 7.64 5233.75 -- AV 54.00 -- -- -- -- -- -- 7320.00 46.26 PK 74.00 27.74 34.57 37.46 9.23 35.00 11.69 7320.00 -- AV 54.00 -- -- -- -- -- --

V1.0 Page 15 of 32 Report No.: CTL1906053014-WF Frequency(MHz): 2480 Polarity: HORIZONTAL Pre- Frequency Emission Limit Margin Raw Antenna Cable Correction amplifier (MHz) Level (dBuV/m) (dB) Value Factor Factor (dB) Factor (dBuV/m) (dBuV) (dB/m) (dB) (dB/m) 4960.00 48.74 PK 74.00 25.26 43.82 33.84 7.00 35.92 4.92 4960.00 -- AV 54.00 -- -- -- -- -- -- 5325.50 44.02 PK 74.00 29.98 36.48 34.67 7.22 34.35 7.54 5325.50 -- AV 54.00 -- -- -- -- -- -- 7440.00 46.89 PK 74.00 27.11 34.94 37.64 9.28 34.97 11.95 7440.00 -- AV 54.00 -- -- -- -- -- -- Frequency(MHz): 2480 Polarity: VERTICAL Pre- Frequency Emission Limit Margin Raw Antenna Cable Correction amplifier (MHz) Level (dBuV/m) (dB) Value Factor Factor (dB) Factor (dBuV/m) (dBuV) (dB/m) (dB) (dB/m) 4960.00 47.96 PK 74.00 26.04 43.04 33.84 7.00 35.92 4.92 4960.00 -- AV 54.00 -- -- -- -- -- -- 5325.50 43.89 PK 74.00 30.11 36.70 34.36 7.10 34.27 7.19 5325.50 -- AV 54.00 -- -- -- -- -- -- 7440.00 46.74 PK 74.00 27.26 34.79 37.64 9.28 34.97 11.95 7440.00 -- AV 54.00 -- -- -- -- -- -- REMARKS: 1. Emission level (dBuV/m) =Raw Value (dBuV)+Correction Factor (dB/m) 2. Correction Factor (dB/m) = Antenna Factor (dB/m)+Cable Factor (dB)-Pre-amplifier Factor 3. Margin value = Limit value- Emission level. 4. -- Mean the PK detector measured value is below average limit. 5. The other emission levels were very low against the limit. 6. RBW1MHz VBW3MHz Peak detector is for PK value; RBW 1MHz VBW10Hz Peak detector is for AV value.

V1.0 Page 16 of 32 Report No.: CTL1906053014-WF Results of Band Edges Test (Radiated) Frequency(MHz): 2402 Polarity: HORIZONTAL Pre- Frequency Emission Limit Margin Raw Antenna Cable Correction amplifier (MHz) Level (dBuV/m) (dB) Value Factor Factor (dB) Factor (dBuV/m) (dBuV) (dB/m) (dB) (dB/m) 2402.00 95.12 PK -- -- 61.73 28.78 4.61 0.00 33.39 2402.00 90.54 AV -- -- 57.15 28.78 4.61 0.00 33.39 2357.75 44.89 PK 74.00 29.11 11.81 28.52 4.56 0.00 33.08 2357.75 -- AV 54.00 -- -- -- -- -- -- 2390.00 45.36 PK 74.00 28.64 12.04 28.72 4.60 0.00 33.32 2390.00 -- AV 54.00 -- -- -- -- -- -- 2400.00 47.45 PK 74.00 26.55 14.06 28.78 4.61 0.00 33.39 2400.00 -- AV 54.00 -- -- -- -- -- -- Frequency(MHz): 2402 Polarity: VERTICAL Pre- Frequency Emission Limit Margin Raw Antenna Cable Correction amplifier (MHz) Level (dBuV/m) (dB) Value Factor Factor (dB) Factor (dBuV/m) (dBuV) (dB/m) (dB) (dB/m) 2402.00 94.35 PK -- -- 60.96 28.78 4.61 0 33.39 2402.00 89.63 AV -- -- 56.24 28.78 4.61 0 33.39 2357.75 45.12 PK 74 28.88 12.04 28.52 4.56 0 33.08 2357.75 -- AV 54 -- -- -- -- -- -- 2390.00 46.34 PK 74 27.66 13.02 28.72 4.60 0 33.32 2390.00 -- AV 54 -- -- -- -- -- -- 2400.00 47.68 PK 74 26.32 14.29 28.78 4.61 0 33.39 2400.00 -- AV 54 -- -- -- -- -- -- Frequency(MHz): 2480 Polarity: HORIZONTAL Pre- Frequency Emission Limit Margin Raw Antenna Cable Correction amplifier (MHz) Level (dBuV/m) (dB) Value Factor Factor (dB) Factor (dBuV/m) (dBuV) (dB/m) (dB) (dB/m) 2480.00 94.69 PK -- -- 61.07 28.92 4.70 0.00 33.62 2480.00 90.12 AV -- -- 56.5 28.92 4.70 0.00 33.62 2483.50 47.62 PK 74 26.38 13.99 28.93 4.70 0.00 33.63 2483.50 -- AV 54 -- -- -- -- -- -- 2491.95 43.12 PK 74 30.88 9.46 28.95 4.71 0.00 33.66 2491.95 -- AV 54 -- -- -- -- -- -- 2500.00 43.28 PK 74 30.72 9.6 28.96 4.72 0.00 33.68 2500.00 -- AV 54 -- -- -- -- -- -- Frequency(MHz): 2480 Polarity: VERTICAL Pre- Frequency Emission Limit Margin Raw Antenna Cable Correction amplifier (MHz) Level (dBuV/m) (dB) Value Factor Factor (dB) Factor (dBuV/m) (dBuV) (dB/m) (dB) (dB/m) 2480.00 93.58 PK -- -- 59.96 28.92 4.70 0.00 33.62 2480.00 89.36 AV -- -- 55.74 28.92 4.70 0.00 33.62 2483.50 47.58 PK 74 26.42 13.95 28.93 4.70 0.00 33.63 2483.50 -- AV 54 -- -- -- -- -- -- 2489.05 43.26 PK 74 30.74 9.6 28.95 4.71 0.00 33.66 2489.05 -- AV 54 -- -- -- -- -- -- 2500.00 43.39 PK 74 30.61 9.71 28.96 4.72 0.00 33.68 2500.00 -- AV 54 -- -- -- -- -- -- REMARKS: 1. Emission level (dBuV/m) =Raw Value (dBuV)+Correction Factor (dB/m)

V1.0 Page 17 of 32 Report No.: CTL1906053014-WF 2. Correction Factor (dB/m) = Antenna Factor (dB/m)+Cable Factor (dB)-Pre-amplifier Factor 3. Margin value = Limit value- Emission level. 4. -- Mean the PK detector measured value is below average limit. 5. The other emission levels were very low against the limit. 6. RBW1MHz VBW3MHz Peak detector is for PK value; RBW 1MHz VBW10Hz Peak detector is for AV value. 7. For fundamental frequency, RBW 3MHz VBW 3MHz Peak detector is for PK Value; RMS detector is for AV value.

V1.0 Page 18 of 32 Report No.: CTL1906053014-WF 3.3. Maximum Conducted Output Power Limit The Maximum Peak Output Power Measurement is 30dBm. Test Procedure Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the power sensor. Test Configuration EUT Power Sensor Power Meter Test Results Output power Type Channel Limit (dBm) Result (dBm) 00 4.707 GFSK 19 3.735 30.00 Pass 39 3.618 Note: 1.The test results including the cable lose.

V1.0 Page 19 of 32 Report No.: CTL1906053014-WF 3.4. Power Spectral Density Limit For digitally modulated systems, the power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission. Test Procedure 1. Use this procedure when the maximum peak conducted output power in the fundamental emission is used to demonstrate compliance. 2. Set the RBW ≥ 3 kHz. 3. Set the VBW ≥ 3× RBW. 4. Set the span to 1.5 times the DTS channel bandwidth. 5. Detector = peak. 6. Sweep time = auto couple. 7. Trace mode = max hold. 8. Allow trace to fully stabilize. 9. Use the peak marker function to determine the maximum power level. 10. If measured value exceeds limit, reduce RBW (no less than 3 kHz) and repeat. 11. The resulting peak PSD level must be 8dBm. Test Configuration EUT SPECTRUM ANALYZER Test Results Power Spectral Density Type Channel Limit (dBm/3KHz) Result (dBm/3KHz) 00 -3.028 GFSK 19 -2.471 8.00 Pass 39 -2.562 Test plot as follows:

V1.0 Page 20 of 32 Report No.: CTL1906053014-WF BLE GFSK CH00 CH19 CH39

V1.0 Page 21 of 32 Report No.: CTL1906053014-WF 3.5. 6dB Bandwidth Limit For digital modulation systems, the minimum 6 dB bandwidth shall be at least 500 kHz Test Procedure The transmitter output was connected to the spectrum analyzer through an attenuator. The bandwidth of the fundamental frequency was measured by spectrum analyzer with 100 KHz RBW and 300 KHz VBW. The 6dB bandwidth is defined as the total spectrum the power of which is higher than peak power minus 6dB. Test Configuration EUT SPECTRUM ANALYZER Test Results 6dB Bandwidth 99% OBW Type Channel Limit (KHz) Result (MHz) (MHz) 00 0.6472 1.0323 GFSK 19 0.6431 1.0136 ≥500 Pass 39 0.6375 1.0104 Test plot as follows:

V1.0 Page 22 of 32 Report No.: CTL1906053014-WF BLE GFSK CH00 CH19 CH39

V1.0 Page 23 of 32 Report No.: CTL1906053014-WF 3.6. Out-of-band Emissions Limit In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF con-ducted or a radiated measurement, pro-vided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter com-plies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20 dB. Attenuation below the general limits specified in §15.209(a) is not required. Test Procedure Connect the transmitter output to spectrum analyzer using a low loss RF cable, and set the spectrum analyzer to RBW=100 kHz, VBW= 300 kHz, peak detector , and max hold. Measurements utilizing these setting are made of the in-band reference level, bandedge and out-of-band emissions. Test Configuration SPECTRUM EUT ANALYZER Test Results Remark: The measurement frequency range is from 30MHz to the 10th harmonic of the fundamental frequency. The lowest, middle and highest channels are tested to verify the spurious emissions and bandage measurement data. Test plot as follows:

V1.0 Page 24 of 32 Report No.: CTL1906053014-WF CH00 CH19 Reference Reference 30MHz-3GHz 30MHz-3GHz 3GHz-25GHz 3GHz-25GHz

V1.0 Page 25 of 32 Report No.: CTL1906053014-WF CH39 Reference 30MHz-3GHz 3GHz-25GHz

V1.0 Page 26 of 32 Report No.: CTL1906053014-WF Band-edge Measurements for RF Conducted Emissions: BLE GFSK Left bandedge Right bandedge

V1.0 Page 27 of 32 Report No.: CTL1906053014-WF 3.7. Antenna Requirement Standard Applicable For intentional device, according to FCC 47 CFR Section 15.203: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited FCC CFR Title 47 Part 15 Subpart C Section 15.247(c) (1) (I): (i) Systems operating in the 2400-2483.5 MHz band that is used exclusively for fixed. Point-to-point operations may employ transmitting antennas with directional gain greater than 6dBi provided the maximum conducted output power of the intentional radiator is reduced by 1 dB for every 3 dB that the directional gain of the antenna exceeds 6dBi. Test Result: The maximum gain of antenna was 0dBi. Antenna

V1.0 Page 28 of 32 Report No.: CTL1906053014-WF 4. Test Setup Photos of the EUT

V1.0 Page 29 of 32 Report No.: CTL1906053014-WF 5. External and Internal Photos of the EUT External photos

V1.0 Page 30 of 32 Report No.: CTL1906053014-WF

V1.0 Page 31 of 32 Report No.: CTL1906053014-WF Internal photos

V1.0 Page 32 of 32 Report No.: CTL1906053014-WF Antenna ********************** End of Report **********************


Document Created: 2019-08-28 16:00:52
Document Modified: 2019-08-28 16:00:52
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC