FCC Part 15.407 Test Report

FCC ID: X4GS00947

Test Report

Download: PDF
FCCID_2986533

Test Report Prepared for: Taser International, Inc. Model: T00064 Description: Body Worn Camera Serial Number: X81002508 FCC ID: X4GS00947 To FCC Part 15.407 Date of Issue: April 28, 2016 On the behalf of the applicant: Taser International, Inc. 17800 N. 85th St. Scottsdale, AZ 85260 Attention of: Bryan Chiles Ph: (480)502-6260 E-mail: bchiles@taser.com Prepared By Compliance Testing, LLC 1724 S. Nevada Way Mesa, AZ 85204 (480) 926-3100 phone / (480) 926-3598 fax www.compliancetesting.com Project No: p1640013 Alex Macon Project Test Engineer This report may not be reproduced, except in full, without written permission from Compliance Testing. All results contained herein relate only to the sample tested. p1640013_FCC_Part 15.407_U-NII-3_Rev 4.0 Page 1 of 18

Test Report Revision History Revision Date Revised By Reason for Revision 1.0 April 14, 2016 Alex Macon Original Document 2.0 April 19, 2016 Amanda Reed Updated serial number Removed copy and paste error from PSD table. 3.0 April 28, 2016 Alex Macon Updated data rates Added Mask plots to Annex A 4.0 April 29, 2016 Alex Macon Updated Power Spectral Density table p1640013_FCC_Part 15.407_U-NII-3_Rev 4.0 Page 2 of 18

Table of Contents Description Page Standard Test Conditions Engineering Practices 6 Test Results Summary 8 Peak Output Power 9 Transmitter Power Spectral Density 11 Undesirable Emissions Conducted 13 Undesirable Emissions Radiated 14 Occupied Bandwidth 16 Frequency Stability 17 Test Equipment Utilized 18 p1640013_FCC_Part 15.407_U-NII-3_Rev 4.0 Page 3 of 18

ILAC / A2LA Compliance Testing, LLC, has been accredited in accordance with the recognized International Standard ISO/IEC 17025:2005. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to the joint ISO-ILAC-IAF Communiqué dated January 2009). The tests results contained within this test report all fall within our scope of accreditation, unless noted below. Please refer to http://www.compliancetesting.com/labscope.html for current scope of accreditation. Testing Certificate Number: 2152.01 FCC Site Reg. #349717 IC Site Reg. #2044A-2 Non-accredited tests contained in this report: N/A p1640013_FCC_Part 15.407_U-NII-3_Rev 4.0 Page 4 of 18

The applicant has been cautioned as to the following 15.21 - Information to User The user’s manual or instruction manual for an intentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 15.27(a) - Special Accessories Equipment marked to a consumer must be capable of complying with the necessary regulations in the configuration in which the equipment is marketed. Where special accessories, such as shielded cables and/or special connectors are required to enable an unintentional or intentional radiator to comply with the emission limits in this part, the equipment must be marketed with, i.e. shipped and sold with, those special accessories. However, in lieu of shipping or packaging the special accessories with the unintentional or intentional radiator, the responsible party may employ other methods of ensuring that the special accessories are provided to the consumer without an additional charge. Information detailing any alternative method used to supply the special accessories for a grant of equipment authorization or retained in the verification records, as appropriate. The party responsible for the equipment, as detailed in § 2.909 of this chapter, shall ensure that these special accessories are provided with the equipment. The instruction manual for such devices shall include appropriate instructions on the first page of text concerned with the installation of the device that these special accessories must be used with the device. It is the responsibility of the user to use the needed special accessories supplied with the equipment. p1640013_FCC_Part 15.407_U-NII-3_Rev 4.0 Page 5 of 18

Standard Test Conditions Engineering Practices Except as noted herein, the following conditions and procedures were observed during the testing: In accordance with C63.10-2013 and unless otherwise indicated in the specific measurement results, the ambient temperature of the actual EUT was maintained within the range of 10° to 40°C (50° to 104°F) unless the particular equipment requirements specified testing over a different temperature range. Also, unless otherwise indicated, the humidity levels were in the range of 10% to 90% relative humidity. Measurement results, unless otherwise noted, are worst-case measurements. Environmental Conditions Temperature Humidity Pressure (ºC) (%) (mbar) 23.1 – 24.2 27.6 – 34.2 967.2 – 977.4 EUT Operation during Tests EUT Description Model: T00064 Description: Body Worn Camera Firmware: N/A Software: N/A Serial Number: X81002508 Additional Information: The EUT was placed in needed test modes by the manufacturer who was on site during all testing p1640013_FCC_Part 15.407_U-NII-3_Rev 4.0 Page 6 of 18

EUT Specifications Maximum Output Power 18.8 dBm Frequency Range 5745 – 5825 MHz Bandwidths 20 MHz 802.11a 6/9/12/24/36/48/54 Mbps Data Rates 802.11n20: MCS0 – MCS7 Antenna List No. Manufacturer Part # Antenna Type Peak Gain 1 Taser HP-VTS01-43100GN PIFA 3.9 dBi 15.203: Antenna Requirement: X The antenna is permanently attached to the EUT The antenna uses a unique coupling The EUT must be professionally installed The antenna requirement does not apply Accessories: None Cables: None Modifications: None p1640013_FCC_Part 15.407_U-NII-3_Rev 4.0 Page 7 of 18

Test Results Summary Pass, Specification Test Name Comments Fail, N/A §15.203 Antenna Requirements Pass §15.207 Line Conducted Emissions N/A This is not affected by the C2PC §15.407(b)(6) §15.407(a)(3) Conducted Output Power Pass §15.407(a)(3),(5) Power Spectral Density Pass 6dB Occupied Bandwidth §15.403(i) Pass §15.407(e) 99% Occupied Bandwidth §15.407(b)(4) Undesirable Emissions Pass General Field Strength Limits §15.205 (Restricted Bands and Pass §15.407(b)(4),(5),(6) Radiated Emission limits) §15.407(g) Frequency Stability Pass §15.407(f) RF Exposure Pass References Description CFR47, Part 15, Subpart B Unintentional Radiators CFR47, Part 15, Subpart C Intentional Radiators CFR47, Part 15, Subpart E Unlicensed Nation Information Infrastructure Devices (U-NII) ANSI C63.10-2009 American National standard for testing Unlicensed Wireless Devices Method and Measurements of Radio-Noise Emissions from low-Voltage ANSI C63.4-2009 Electrical and Electronic Equipment in the range 9kHz to 40GHz. General requirements for the Competence of Testing and Calibrations ISO/IEC 17025:2005 Laboratories KDB 644545 D03 Guidance for IEEE 802 11ac New Rules KDB 789033 D02 General U-NII Test Procedures New Rules V01 KDB 926956 D01 U-NII Transition Plan p1640013_FCC_Part 15.407_U-NII-3_Rev 4.0 Page 8 of 18

Peak Output Power Engineer: Alex Macon Test Date: 4/7/16 Test Requirements For the band 5.725-5.85 GHz, the maximum conducted output power over the frequency band of operation shall not exceed 1 W. If transmitting antennas of directional gain greater than 6 dBi are used, the maximum conducted output power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. However, fixed point- to-point U-NII devices operating in this band may employ transmitting antennas with directional gain greater than 6 dBi without any corresponding reduction in transmitter conducted power. Fixed, point-to-point operations exclude the use of point-to-multipoint systems, omnidirectional applications, and multiple collocated transmitters transmitting the same information. The operator of the U-NII device, or if the equipment is professionally installed, the installer, is responsible for ensuring that systems employing high gain directional antennas are used exclusively for fixed, point-to-point operations. Test Procedure The RF power was calculated using the spectrum analyzers’ band power function per Method SA-1 from KDB 789033 D02 General U-NII Test Procedures New Rules v01. Measurements were made at the low, mid and high channels of the band. The Spectrum analyzer was set to the following: a. RBW = 1 MHz b. VBW ≥ 3 MHz c. Sweep time = auto d. Detector = RMS e. 100 traces in power averaging mode Test Setup EUT Spectrum Attenuator Analyzer p1640013_FCC_Part 15.407_U-NII-3_Rev 4.0 Page 9 of 18

Test Results Bandwidth Frequency Level Limit Margin TP Mode (MHz) (MHz) (dBm) (dBm) (dB) 20 5745 20 18.5 30 -11.5 A 20 5785 20 18.8 30 -11.2 A 20 5825 20 18.3 30 -11.7 A 20 5745 20 18.8 30 -11.3 N 20 5785 20 18.5 30 -11.5 N 20 5825 20 18.1 30 -11.9 N p1640013_FCC_Part 15.407_U-NII-3_Rev 4.0 Page 10 of 18

Transmitter Power Spectral Density Engineer: Alex Macon Test Date: 4/7/16 Test Requirements For the band 5.725-5.85 GHz, the maximum power spectral density shall not exceed 30 dBm in any 500 kHz band. If transmitting antennas of directional gain greater than 6 dBi are used, the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. However, fixed point-to-point U-NII devices operating in this band may employ transmitting antennas with directional gain greater than 6 dBi without any corresponding reduction in power spectral density. Test Procedure The Power Spectral Density was measured using the method per SA-1 from KDB 789033 D02 General U-NII Test Procedures New Rules v01. Measurements were made at the low, mid and high channels of the band. The maximum PSD was determine by finding the peak value across the carrier bandwidth. The Spectrum Analyzer was set to the following: a. RBW = 500 KHz. b. VBW ≥ 1500 MHz c. Span 1.5 * BW d. Sweep time = auto e. Detector = RMS f. 100 traces in power averaging mode Test Setup Spectrum EUT Attenuator Analyzer p1640013_FCC_Part 15.407_U-NII-3_Rev 4.0 Page 11 of 18

Test Results Bandwidth Frequency J3 Level Limit/500KHz Margin TP Mode (MHz) (MHz) (dBm) (dBm) (dB) 20 5745 20 9.7 30 -20.3 A 20 5785 20 9.6 30 -20.4 A 20 5825 20 9.3 30 -20.7 A 20 5745 20 9.6 30 -20.4 N 20 5785 20 9.6 30 -20.4 N 20 5825 20 9.0 30 -21.0 N p1640013_FCC_Part 15.407_U-NII-3_Rev 4.0 Page 12 of 18

Undesirable Emissions Conducted Engineer: Alex Macon Test Date: 4/7/16 Test Requirements Unwanted Emissions that fall Outside Restricted Bands For transmitters operating in the 5.725-5.85 GHz band: All emissions within the frequency range from the band edge to 10 MHz above or below the band edge shall not exceed an e.i.r.p. of −17 dBm/MHz; for frequencies 10 MHz or greater above or below the band edge, emissions shall not exceed an e.i.r.p. of −27 dBm/MHz. The emission measurements shall be performed using a minimum resolution bandwidth of 1 MHz. A lower resolution bandwidth may be employed near the band edge, when necessary, provided the measured energy is integrated to show the total power over 1 MHz The provisions of §15.205 apply to intentional radiators operating under this section. Unwanted emissions below 1 GHz must comply with the general field strength limits set forth in §15.209. For Conducted Unwanted Emissions in the Restricted Bands For conducted measurements above 1000 MHz, EIRP was determined and then the field strength computed by the following: E[dBμV/m] = EIRP[dBm] - 20 log(d[meters]) + 104.77, where E = field strength and d = 3m E[dBμV/m] = EIRP[dBm] + 95.2, for d = 3 meters. Test Procedure Per KDB 789033 D02 General U-NII Test Procedures New Rules v01 conducted RF port measurements were made in lieu of radiated. In addition, Cabinet Emissions measurements were performed in a semi-anechoic chamber with the antenna port terminated by a matching load. See additional section for Radiated Emissions. The following criteria were addressed: The Spectrum Analyzer was set to the following for emissions > 1000MHz: a. RBW = 1 MHz b. VBW ≥ 3 MHz c. Detector = Peak. d. Sweep time = auto. e. Trace mode = max hold. 1. Note: For emissions where the peak exceeded that of the average 15.209 emission limit the following was performed. f. RBW = 1 MHz g. VBW ≤ RBW/100 (i.e., 10 kHz) but not less than 10 Hz. For emissions below 1000MHz the Spectrum Analyzer settings were as follows: a. RBW = 100 kHz b. VBW ≥ 300 kHz c. Detector = Peak. d. Sweep time = auto. e. Trace mode = max hold. Test Setup EUT Attenuator Spectrum Analyzer Test Results: See Annex A: Undesirable Emissions Conducted p1640013_FCC_Part 15.407_U-NII-3_Rev 4.0 Page 13 of 18

Undesirable Emissions Radiated Engineer: Alex Macon Test Date: 4/8/16 Test Requirements The provision of §15.209 were applied. In addition the requirements of §15.205 were also applied. FCC Part 15 Subpart C Paragraph 15.209(a) Limits Frequency Frequency Frequency (MHz) (microvolts/meter) (meter) 0.009-0.490 2400/F(kHz) 300 0.490-1.705 24000/F(kHz) 30 1.705-30 30 30 30-88 100 3 88-216 150 3 216-960 200 3 Above 960 500 3 Remarks: E field strength (dBμV/m) = 20 log E field strength (uV/m) Test Procedure The EUT was setup in accordance with ANSI C63.10. 2013 and tested per KDB 789033. The antenna was replaced with non-radiating matched load. The EUT is placed on non-conductive platform at a height of 0.8 meters above the ground plane of the semi-anechoic chambers. The EUT was rotated 360 degrees and the receive antenna raised and lowered to th find the maximum emissions from 30MHz to the 10 harmonic of the fundamental. The EUT was set to the maximum power level allowed and the low, mid, and high channels were investigated for emissions. The Spectrum Analyzer was set to the following for emissions > 1000MHz: a. (RBW = 1 MHz b. VBW ≥ 3 MHz c. Detector = Peak. d. Sweep time = auto. e. Trace mode = max hold. 1. Note: For emissions where the peak exceeded that of the average 15.209 emission limit the following was performed. f. RBW = 1 MHz g. VBW ≤ RBW/100 (i.e., 10 kHz) but not less than 10Hz For emissions below 1000MHz the Spectrum Analyzer settings were as follows: a. RBW = 100 kHz b. VBW ≥ 300 kHz c. Detector = Peak. d. Sweep time = auto. e. Trace mode = max hold. 1. Note: A quasi peak detector was used for emissions where the peak exceeded that of the average 15.209 emission limits p1640013_FCC_Part 15.407_U-NII-3_Rev 4.0 Page 14 of 18

Test Setup below 1000MHz EUT Antenna with Spectrum Preamp Analyzer Test Setup above 1000MHz Band EUT with Antenna Amplifier Spectrum Reject matching load Analyzer Filter Test Results: See Annex B: Undesirable Emission Radiated p1640013_FCC_Part 15.407_U-NII-3_Rev 4.0 Page 15 of 18

Occupied Bandwidth Engineer: Alex Macon Test Date: 4/7/16 Test Requirement Within the 5.725-5.85 GHz band, the minimum 6 dB bandwidth of U-NII devices shall be at least 500 kHz. For purposes of this subpart the emission bandwidth shall be determined by measuring the width of the signal between two points, one below the carrier center frequency and one above the carrier center frequency, that are 6 dB down relative to the maximum level of the modulated carrier. Determination of the emissions bandwidth is based on the use of measurement instrumentation employing a peak detector function with an instrument resolution bandwidth approximately equal to 1.0 percent of the emission bandwidth of the device under measurement Test Procedure The Spectrum analyzer was set to the following parameters a. RBW = 100 kHz. b. VBW ≥ 300 kHz c. Detector = Peak. d. Trace mode = max hold. Test Setup EUT Spectrum Analyzer Test Results: See Annex C: Occupied Bandwidth p1640013_FCC_Part 15.407_U-NII-3_Rev 4.0 Page 16 of 18

Frequency Stability Engineer: Alex Macon Test Date: 4/8/16 Test Requirement Manufacturers of U-NII devices are responsible for ensuring frequency stability such that an emission is maintained within the band of operation under all conditions of normal operation as specified in the user’s manual. Test Procedure a. The EUT was placed into a temperature chamber and the temperature ranges were set to the manufacturers’ specifications. b. The RF output of the EUT was connected to a spectrum analyzer c. The lowest and highest channels of the band were set to transmit d. The carrier plots were measured to insure that the 6dB band width remained within the band over the prescribed temperature extremes. Test Setup Temperature Chamber Spectrum EUT Analyzer Test Results: See Annex D: Frequency Stability p1640013_FCC_Part 15.407_U-NII-3_Rev 4.0 Page 17 of 18

Test Equipment Utilized Description Manufacturer Model # CT Asset # Last Cal Date Cal Due Date Temperature Chamber Tenney Tenney Jr i00027 Verified on: 4/7/16 Horn Antenna, Amplified ARA DRG-118/A i00271 5/8/14 5/8/16 Horn Antenna, Amplified ARA MWH-1826/B i00273 4/22/15 4/22/18 Humidity / Temp Meter Newport IBTHX-W-5 i00282 4/1/15 4/1/16 Spectrum Analyzer Agilent E4407B i00331 9/18/15 9/18/16 Data Logger Fluke Hydra Data Bucket i00343 4/5/16 4/5/17 Bi-Log Antenna Schaffner CBL 6111D i00349 10/19/15 10/19/17 EMI Analyzer Agilent E7405A i00379 2/11/16 2/11/17 3 Meter Semi-Anechoic 3 Meter Semi-Anechoic Panashield i00428 7/27/14 7/27/16 Chamber Chamber PSA Spectrum Analyzer Agilent E4445A i00471 8/26/15 8/26/16 In addition to the above listed equipment standard RF connectors and cables were utilized in the testing of the described equipment. Prior to testing these components were tested to verify proper operation. END OF TEST REPORT p1640013_FCC_Part 15.407_U-NII-3_Rev 4.0 Page 18 of 18


Document Created: 2019-10-12 10:20:39
Document Modified: 2019-10-12 10:20:39
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC