Ref. XP5800 Test Rpt HAC RF Part 2

FCC ID: WYPPG2132

RF Exposure Info

Download: PDF
FCCID_3670836

DASY5 E—field Result Date: 17.03.2017 Test Laboratory: SPEAG Lab2 DUT: HAC—Dipole 835 MHz; Type: CD835V3; Serial: CD835V3 — SN: 1171 Communication System: UID 0 — CW ; Frequency: 835 MHz Medium parameters used: 0 = 0 S/m, €r = 1; p = 1000 kg/m* Phantom section: RF Section Measurement Standard: DASYS5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: e Probe: ER3DV6 — SN2336; ConvF(1, 1, 1); Calibrated: 30.12.2016; e Sensor—Surface: (Fix Surface) e Electronics: DAE4 Sn781; Calibrated: 02.09.2016 e Phantom: HAC Test Arch with AMCC; Type: SD HAC PO1 BA; Serial: 1070 e DASY52 52.8.8(1222); SEMCAD X 14.6.10(7331) Dipole E—Field measurement @ 835MHz/E—Scan — 835MHz d=15mm/Hearing Aid Compatibility Test (41x361x1): Interpolated grid: dx=0.5000 mm, dy=0.5000 mm Device Reference Point: 0, 0, —6.3 mm Reference Value = 106.2 V/m; Power Drift = —0.03 dB Applied MIF = 0.00 dB RF audio interference level = 40.61 dBV/m Emission category: M3 MIF scaled E—field Grid 4 M4 ( Grid 6 M4 35.82 dBV/m|35.9 /m|35.86 dBV/m 40.21 dBV/m|40.61 dBV/m|40.59 dBV/m —2.00 —3.99 —5.99 —£.98 —9.98 0 dB = 107.3 V/m = 40.61 dBV/m Certificate No: CD835V3—1171_Mar17 Page 5 of 5

Calibration Laboratory of A*x\x//%Sz Schweizerischer Kalibrierdienst : SLN S Schmid & Partner i‘lafi&i C Service suisse d‘étalonnage Englneerlng AG z /R T 5 Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland 7, N Swiss Calibration Service /I/”/I l n\“\\\ Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client Sporton—KS (Auden) Certificate No: CD1880V3—1155_Mari17 |CALIBRATION CERTIFICATE Object CD1880V3 — SN: 1155 Calibration procedure(s) QA CAL—20.v6 Calibration procedure for dipoles in air Calibration date: March 20, 2017 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter NRP SN: 104778 06—Apr—16 (No. 217—02288/02289) Apr—17 Power sensor NRP—Z91 SN: 103244 06—Apr—16 (No. 217—02288) Apr—17 Power sensor NRP—Z91 SN: 103245 06—Apr—16 (No. 217—02289) Apr—17 Reference 20 dB Attenuator SN: 5058 (20k) 05—Apr—16 (No. 217—02292) Apr—17 Type—N mismatch combination SN: 5047.2 / 06327 05—Apr—16 (No. 217—02295) Apr—17 Probe ER3DV6 SN: 2336 30—Dec—16 (No. ER3—2336_Dec16) Dec—17 Probe H3DV6 SN: 6065 30—Dec—16 (No. H3—6065_Dec16) Dec—17 DAE4 SN: 781 02—Sep—16 (No. DAE4—781_Sep16) Sep—17 Secondary Standards ID # Check Date (in house) Scheduled Check Power meter Agilent 4419B SN: GB42420191 09—Oct—09 (in house check Sep—14) In house check: Oct—17 Power sensor HP E4412A SN: US38485102 O05—Jan—10 (in house check Sep—14) In house check: Oct—17 Power sensor HP 8482A SN: US37295597 09—Oct—09 (in house check Sep—14) In house check: Oct—17 RF generator R&S SMT—O6 SN: 832283/011 27—Aug—12 (in house check Oct—15) In house check: Oct—17 Network Analyzer HP 8753E SN: US37390585 18—Oct—01 (in house check Oct—16) In house check: Oct—17 Name Function Signature Calibrated by: Johannes Kurikka Laboratory Technician /?/////éw —eAKE: Approved by: Katja Pokovic Technical Manager Issued: March 20, 2017 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: CD1880V3—1155_Mar17 Page 1 of 5

w # wthlty» Calibration . Laboratory of $\“\\\\//I/‘7> S Schweizerischer Kalibrierdienst Schmid & Partner il;‘\\/i\‘/IME/fi C Service suisse d‘étalonnage Engineering AG < //—\\ x 5 Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland ‘r/,,/fi\\\@ Swiss Calibration Service Alnlads® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates References (1] ANSI—C63.19—2011 American National Standard, Methods of Measurement of Compatibility between Wireless Communications Devices and Hearing Aids. Methods Applied and Interpretation of Parameters: e Coordinate System: y—axis is in the direction of the dipole arms. z—axis is from the basis of the antenna (mounted on the table) towards its feed point between the two dipole arms. x—axis is normal to the other axes. In coincidence with the standards [1], the measurement planes (probe sensor center) are selected to be at a distance of 15 mm above the top metal edge of the dipole arms. e Measurement Conditions: Further details are available from the hardcopies at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. The forward power to the dipole connector is set with a calibrated power meter connected and monitored with an auxiliary power meter connected to a directional coupler. While the dipole under test is connected, the forward power is adjusted to the same level. e Antenna Positioning: The dipole is mounted on a HAC Test Arch phantom using the matching dipole positioner with the arms horizontal and the feeding cable coming from the floor. The measurements are performed in a shielded room with absorbers around the setup to reduce the reflections. It is verified before the mounting of the dipole under the Test Arch phantom, that its arms are perfectly in a line. It is installed on the HAC dipole positioner with its arms parallel below the dielectric reference wire and able to move elastically in vertical direction without changing its relative position to the top center of the Test Arch phantom. The vertical distance to the probe is adjusted after dipole mounting with a DASYS5 Surface Check job. Before the measurement, the distance between phantom surface and probe tip is verified. The proper measurement distance is selected by choosing the matching section of the HAC Test Arch phantom with the proper device reference point (upper surface of the dipole) and the matching grid reference point (tip of the probe) considering the probe sensor offset. The vertical distance to the probe is essential for the accuracy. e Feed Point Impedance and Return Loss: These parameters are measured using a HP 8753E Vector Network Analyzer. The impedance is specified at the SMA connector of the dipole. The influence of reflections was eliminating by applying the averaging function while moving the dipole in the air, at least 70cm away from any obstacles. e E—field distribution: E field is measured in the x—y—plane with an isotropic ER3D—field probe with 100 mW forward power to the antenna feed point. In accordance with [1], the scan area is 20mm wide, its length exceeds the dipole arm length (180 or 9O0mm). The sensor center is 15 mm (in z) above the metal top of the dipole arms. Two 3D maxima are available near the end of the dipole arms. Assuming the dipole arms are perfectly in one line, the average of these two maxima (in subgrid 2 and subgrid 8) is determined to compensate for any non—parallelity to the measurement plane as well as the sensor displacement. The E—field value stated as calibration value represents the maximum of the interpolated 3D—E—field, in the plane above the dipole surface. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: CD1880V3—1155_Mar17 Page 2 of 5

Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY5 V52.8.8 Phantom HAC Test Arch Distance Dipole Top — Probe Center 15 mm Scan resolution dx, dy = 5 mm Frequency 1880 MHz + 1 MHz Input power drift < 0.05 dB Maximum Field values at 1880 MHz E—field 15 mm above dipole surface condition Interpolated maximum Maximum measured above high end 100 mW input power 91.4 V/m = 39.22 dBV/m Maximum measured above low end 100 mW input power 90.1 V/m = 39.09 dBV/m Averaged maximum above arm 100 mW input power 90.7 V/im + 12.8 % (k=2) Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters Frequency Return Loss Impedance 1730 MHz 36.7 dB 50.2 f — 1.5 |{2 1880 MHz 18.2 dB 51.1 Q + 12.5 jQ 1900 MHz 18.6 dB 54.3 Q + 11.6 jQ 1950 MHz 22.9 dB 55.3 Q + 5.3 jQ 2000 MHz 19.6 dB 50.6 Q + 10.6 jQ 3.2 Antenna Design and Handling The calibration dipole has a symmetric geometry with a built—in two stub matching network, which leads to the enhanced bandwidth. The dipole is built of standard semirigid coaxial cable. The internal matching line is open ended. The antenna is therefore open for DC signals. Do not apply force to dipole arms, as they are liable to bend. The soldered connections near the feedpoint may be damaged. After excessive mechanical stress or overheating, check the impedance characteristics to ensure that the internal matching network is not affected. After long term use with 40W radiated power, only a slight warming of the dipole near the feedpoint can be measured. Certificate No: CD1880V3—1155_Mari17 Page 3 of 5

Impedance Measurement Plot 20 Mar 2017 13:09:46 (CHI) §Si1i LOG 5 dBAREF —18 dB 1t~18.161 dB 1 8£80.000 doo MHz CH1 Markers 2:—36.741 dB 1.73000 GHz Cor 3:—18,.600 dB 1.390000 GHz 4—22,.947 dB 1,395000 GHz A¥g 16 S:—19.550 dB 2.00000 GHz H1d CH2~ $44 1 U FS 1: S1L.117 & 12.543 a 1.9618 nH 1 8£80.000 d0o MHz CH2 Markers 2: 50178 a for =~1.4473 i 1.73000 GHz 3: 54.266 a 11.9561 6: 1.30000 GHz Aw 16 * H1d 200000 GHz CENTER 1 880.000 00o MHz SPAN 1 900.000 ado MHz Certificate No: CD1880V3—1155_Mar17 Page 4 of 5

DASY5 E—field Result Date: 17.03.2017 Test Laboratory: SPEAG Lab2 DUT: HAC Dipole 1880 MHz; Type: CD1880V3; Serial: CD1880V3 — SN: 1062 Communication System: UID 0 — CW ; Frequency: 1880 MHz Medium parameters used: 0 = 0 S/m, €, = 1; p = 1000 kg/m* Phantom section: RF Section Measurement Standard: DASYS5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: e Probe: ER3DV6 — SN2336; ConvF(1, 1, 1); Calibrated: 30.12.2016; e Sensor—Surface: (Fix Surface) e Electronics: DAE4 Sn781; Calibrated: 02.09.2016 e Phantom: HAC Test Arch with AMCC; Type: SD HAC PO1 BA; Serial: 1070 e DASY52 52.8.8(1222); SEMCA D X 14.6.10(7331) Dipole E—Field measurement @ 1880MHz/E—Scan — 1880MHz d=15mm/Hearing Aid Compatibility Test (41x181x1): Interpolated grid: dx=0.5000 mm, dy=0.5000 mm Device Reference Point: 0, 0, —6.3 mm Reference Value = 160.8 V/m; Power Drift = 0.01 dB Applied MIF = 0.00 dB RF audio interference level = 39.22 dBV/m Emission category: M2 MIF scaled E—field 38.81 dBV/m|39.09 dBV/m|39.05 dBV/m —0.99 —1.99 —2.98 —3.98 —4.97 0 dB = 91.45 V/m =39.22 dBV/m Certificate No: CD1880V3—1155_Mari17 Page 5 of 5

Calibration Laboratory of 5 Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d'etalonnage C Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland s Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is o ne of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client Sporton-TW (Auden) Certificate No: CD2600V3-101O_Nov17 !CALIBRATION CERTIFICATE Object CD2600V3 - SN: 1010 Calibration procedure(s) QA CAL-20.v6 Calibration procedure for dipoles in air Calibration date: November 22, 2017 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (SI). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 ± 3)°C and humidity< 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID# Cal Date (Certificate No.) Scheduled Calibration Power meter NAP SN: 104778 04-Apr-17 (No. 217-02521/02522) Apr-18 Power sensor NRP-Z91 SN: 103244 04-Apr-17 (No. 217-02521) Apr- 18 Power sensor NRP-Z91 SN: 103245 04-Apr-17 (No. 217-02522) Apr-18 Reference 20 dB Attenuator SN: 5058 (20k) 07-Apr-17 (No. 217-02528) Apr-1 8 Type-N mismatch combination SN: 5047.2 / 06327 07-Apr-17 (No. 217-02529) Apr-18 Probe EF3DV3 SN: 4013 14-Jun-17 (No. EF3-4013_Jun17) Jun-18 DAE4 SN: 781 13-Jul-17 (No. DAE4-781 _Jul17) Jul-18 Secondary Standards ID# Check Date (in house) Scheduled Check Power meter Agilent 4419B SN: GB42420191 09-0ct-09 (in house check Oct-17) In house check: Oct-20 Power sensor HP E4412A SN: US38485102 05-Jan-1O (in house check Oct-1 7) In house check: Oct-20 Power sensor HP 8482A SN: US37295597 09-0ct-09 (in house check Oct-17) In house check: Oct-20 RF generator R&S SMT-06 SN: 832283/011 27 -Aug-12 (in house check Oct-17) In house check: Oct-20 Network Analyzer HP 8753E SN: US37390585 18-0ct-01 (in house check Oct-17) In house check: Oct-18 Name Function Signature Calibrated by: Leif Klysner Laboratory Technician Approved by: Katja Pokovic Technical Manager Issued: November 23, 2017 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: CD2600V3-101O_Nov17 Page 1 of 5

Calibration Laboratory of Schmid & Partner s Schweizerischer Kalibrierdienst Service suisse d'etalonnage C Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich , Switzerland s Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SC$ 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement tor the recognition of calibration certificates References [1] ANS1-C63.19-2011 American National Standard, Methods of Measurement of Compatibility between Wireless Communications Devices and Hearing Aids. Methods Applied and Interpretation of Parameters: • Coordinate System: y-axis is in the direction of the dipole arms. z-axis is from the basis of the antenna (mounted on the table) towards its feed point between the two dipole arms. x-axis is normal to the other axes. In coincidence with the standards [1 ], the measurement planes (probe sensor center) are selected to be at a distance of 15 mm above the top metal edge of the dipole arms. • Measurement Conditions: Further details are available from the hardcopies at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. The forward power to the dipole connector is set with a calibrated power meter connected and monitored with an auxiliary power meter connected to a directional coupler. While the dipole under test is connected, the forward power is adjusted to the same level. • Antenna Positioning: The dipole is mounted on a HAC Test Arch phantom using the matching dipole positioner with the arms horizontal and the feeding cable coming from the floor. The measurements are performed in a shielded room with absorbers around the setup to reduce the reflections. It is verified before the mounting of the dipole under the Test Arch phantom, that its arms are perfectly in a line. It is installed on the HAC dipole positioner with its arms parallel below the dielectric reference wire and able to move elastically in vertical direction without changing its relative position to the top center of the Test Arch phantom. The vertical distance to the probe is adjusted after dipole mounting with a DASY5 Surface Check job. Before the measurement, the distance between phantom surface and probe tip is verified. The proper measurement distance is selected by choosing the matching section of the HAC Test Arch phantom with the proper device reference point (upper surface of the dipole} and the matching grid reference point (tip of the probe) considering the probe sensor offset. The vertical distance to the probe is essential for the accuracy. • Feed Point Impedance and Return Loss: These parameters are measured using a HP 8753E Vector Network Analyzer. The impedance is specified at the SMA connector of the dipole. The influence of reflections was eliminating by applying the averaging function while moving the dipole in the air, at least 70cm away from any obstacles. • E-field distribution: E field is measured in the x-y-plane with an isotropic ER3D-field probe with 100 mW forward power to the antenna feed point. In accordance with [1], the scan area is 20mm wide, its length exceeds the dipole arm length (180 or 90mm) . The sensor center is 15 mm (in z) above the metal top of the dipole arms . Two 30 maxima are available near the end of the dipole arms. Assuming the dipole arms are perfectly in one line, the average of these two maxima (in subgrid 2 and subgrid 8) is determined to compensate for any non-parallelity to the measurement plane as well as the sensor displacement. The E-field value stated as calibration value represents the maximum of the interpolated 30-E-field, in the plane above the dipole surface. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: CD2600V3-101O_Nov17 Page 2 of 5

Measurement Conditions DASY system con f'1qurat1on, as ar as not q1ven on paqe 1. DASY Version DASY5 V52.10.0 Phantom HAC Test Arch Distance Dipole Top - Probe Center 15mm Scan resolution dx, dy= 5 mm Frequency 2600 MHz ± 1 MHz Input power drift < 0.05 dB Maximum Field values at 2600 MHz E-field 15 mm above dipole surface condition Interpolated maximum Maximum measured above high end 100 mW input power 85.8 Vim= 38.67 dBV/m Maximum measured above low end 100 mW input power 84.9 Vim= 38.58 dBV/m Averaged maximum above arm 100 mW input power 85.4 Vim ± 12.8 % (k=2) Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters Frequency Return Loss Impedance 2450 MHz 23.6 dB 44.6 Q - 3.3 jQ 2550 MHz 29.4 dB 52.0 Q + 2.8 jQ 2600 MHz 26.8 dB 54.7 Q - 0.7 jQ 2650 MHz 25.3 dB 53.5 Q - 4.4 jQ 2750 MHz 19.4 dB 45.4 Q - 9.2 jQ 3.2 Antenna Design and Handling The calibration dipole has a symmetric geometry with a built-in two stub matching network, which leads to the enhanced bandwidth. The dipole is built of standard semirigid coaxial cable. The internal matching line is open ended. The antenna is therefore open for DC signals. Do not apply force to dipole arms, as they are liable to bend. The soldered connections near the feedpoint may be damaged. After excessive mechanical stress or overheating, check the impedance characteristics to ensure that the internal matching network is not affected. After long term use with 40W radiated power, only a slight warming of the dipole near the feedpoint can be measured. Certificate No: CD2600V3-101O_Nov17 Page 3 of 5

Impedance Measurement Plot 22 Nov 2017 16:54: 43 rnil 811 LOG 5 dB i REF -18 dB 1 : -26. 818 dB 2 600.000 000 MHz * CH1 Markers 2:-23. 560 dB 2 . 45000 GHz Cor 3:-29.422 dB 2.55000 GHz 4:-25. 311 dB 2 . 65000 GHz Av9 16 5:-19.357 dB 2. 75000 GHz Hld CH 2 811 1 U FS 1: 54.715 n -744.14 mo 82. 261 pF 2 600. 000 000 MHz CH 2 Markers 2: 44.652 n Co r -3. 3027 n 2.45000 GHz 3: 51.996 l'l 2.8008 o 2.55000 GHz 4: 53.4 7 1 l'l - 4.4219 l'l 2.65000 GHz 5: 45.408 l'l -9. 2 461 l'l Hld 2.75000 GHz CENTER 2 600.000 000 MHz SPAN 900.000 000 MHz Certificate No: CD2600V3-1010_Nov17 Page 4 of 5

DASY5 E-field Result Date: 2 1.11.20 17 Test Laboratory: SPEAG Lab2 DUT: HAC Dipole 2600 MHz; Type: CD2600V3; Serial: CD2600V3 - SN: 1010 Communication System: UID O - CW ; Frequency: 2600 MHz Medium parameters used: cr = 0 Sim, Er = 1; p = I 000 kg/m3 Phantom section: RF Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63. I 9-201 I ) DASY52 Configuration: • Probe: EF3DV3 - SN4013; ConvF(l, 1, 1); Calibrated : 14.06.2017; • Sensor-Surface: (Fix Surface) • Electronics: DAE4 Sn781; Calibrated: 13.07.2017 • Phantom: HAC Test Arch with AMCC; Type: SD HAC POl BA; Serial: 1070 • DASY52 52.10.0(1446); SEMCAD X 14.6.10(7417) Dipole E-Field measurement @ 2600MHz - with EF_4013/E-Scan - 2600MHz d=l 5mm/Hearing Aid Compatibility Test (41xl81xl): Interpolated grid: dx=0.5000 mm, dy=0.5000 mm Device Reference Point: 0, 0, -6.3 mm Reference Value= 64.99 V/m; Power Drift= -0.04 dB Applied MIF = 0.00 dB RF audio interference level= 38.67 dBV/m Emission category: M2 MIF scaled E-field Grid 1 M2 Grid 2 M2 Grid 3 M2 38.26 dBV/m 38.58 dBV/m 38.53 dBV/m Grid 4 M2 Grid 5 M2 Grid 6 M2 37.93 dBV/m 38.15 dBV/m 38 .12 dBV/m Grid 7 M2 Grid 8 M2 Grid 9 M2 38.42 dBV/m 38.67 dBV/m 38.61 dBV/m dB 0 -1.36 -2.72 -4.08 -5.44 -6.80 0 dB= 85.84 V/m = 38.67 dBV/m Certificate No: CD2600V3-101O_Nov17 Page 5 of 5

EA® In Collaboration with C omm Sss y> EF4A a_‘/"/‘/, s p e a g erCNAS :: TS Zlf uo‘ i CNAS LO570 es CALIBRATION LABORATORY 2. nearnninnaniiinges, e ang CALIBRATION Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2218 Fax: +86—10—62304633—2209 E—mail: cttl@chinattl.com Hitp:/www.chinattl.cn Client : Sporton International INC Certificate No: 217—97153 CALIBRATION CERTIFICATE Object DAE4 — SN: 1326 Calibration Procedure(s) FF—Z11—002—01 Calibration Procedure for the Data Acquisition Electronics (DAEx) Calibration date: September 15, 2017 This calibration Certificate documents the traceability to national standards, which realize the physical units of measurements(Sl). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature(22+3)C and humidity<70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Process Calibrator 753 1971018 27—Jun—17 (CTTL, No.J17X05859) June—18 Name Function Signature Calibrated by: Yu Zongying SAR Test Engineer }.fié—? Reviewed by: Lin Hao SAR Test Engineer fifl%% Approved by: Qi Dianyuan SAR Project Leader O_/ZA_y Issued: September 18, 2017 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: Z17—97153 Page 1 of 3

m \n, Collsboration with a_‘/"/‘/, s p e a q eaaagee>" CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2218 Fax: +86—10—62304633—2209 E—mail: cttl@chinattl.com Hittp:/www.chinattl.cn Glossary: DAE data acquisition electronics Connector angle information used in DASY system to align probe sensor X to the robot coordinate system. Methods Applied and Interpretation of Parameters: e DC Voltage Measurement. Calibration Factor assessed for use in DASY system by comparison with a calibrated instrument traceable to national standards. The figure given corresponds to the full scale range of the voltmeter in the respective range. e Connector angle: The angle of the connector is assessed measuring the angle mechanically by a tool inserted. Uncertainty is not required. e The report provide only calibration results for DAE, it does not contain other performance test results. Certificate No: Z17—97153 Page 2 of 3

mm\© In Collaboration with ‘7/"7‘J, s p e a g aaaayey>"" CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2218 Fax: +86—10—62304633—2209 E—mail: cttl@chinattl.com Http:/www.chinattl.cn DC Voltage Measurement A/D — Converter Resolution nominal High Range: 1LSB = 6.A1uV , full range = —100...+300 mV Low Range: 1LSB = 61nV , full range = ~Avsllll. +3mV DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Calibration Factors X Y Z. High Range 404.898 + 0.15% (k=2) 405.241 + 0.15% (k=2) 404.618 + 0.15% (k=2) Low Range 3.98840 + 0.7% (k=2) 3.99650 + 0.7% (k=2) 3.99854 + 0.7% (k=2) Connector Angle Connector Angle to be used in DASY system 41.5° +1 ° Certificate No: Z17—97153 Page 3 of 3

Ca“b'_'atlon Laboratory of e\“\‘&1/”}7”/,, g Schweizerischer Kalibrierdienst Schmid & Partner M C Service suisse d‘étalonnage Engineering AG PA eV I Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland 2’///;\\\ 3 S Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client Sporton—KS (Auden) Certificate No: ER3—2476_Nov16 CALIBRATION CERTIFICATE Object ER3DV6 — SN:2476 Calibration procedure(s) QA CAL—02.v8, QA CAL—25.v6 Calibration procedure for E—field probes optimized for close near field evaluations in air Calibration date: November 23, 2016 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID Cal Date (Certificate No.) Scheduled Calibration Power meter NRP SN: 104778 06—Apr—16 (No. 217—02288/02289) Apr—17 Power sensor NRP—291 SN: 103244 06—Apr—16 (No. 217—02288) Apr—17 Power sensor NRP—Z91 SN: 103245 06—Apr—16 (No. 217—02289) Apr—17 Reference 20 dB Attenuator SN: S5277 (20%) 05—Apr—16 (No. 217—02293) Apr—17 Reference Probe ER3DV6 SN: 2328 14—Oct—16 (No. ER3—2328_Oct16) Oct—17 DAE4 SN: 789 11—Nov—16 (No. DAE4—789_Nov16) Nov—17 Secondary Standards ID Check Date (in house) Scheduled Check Power meter E4419B SN: GB41293874 06—Apr—16 (in house check Jun—16) In house check: Jun—18 Power sensor E4412A SN: MY41498087 06—Apr—16 (in house check Jun—16) In house check: Jun—18 Power sensor E4412A SN: 000110210 06—Apr—16 (in house check Jun—16) In house check: Jun—18 RF generator HP 8648C SN: US3642U01700 04—Aug—99 (in house check Jun—16) In house check: Jun—18 Network Analyzer HP 8753E SN: US37390585 18—Oct—01 (in house check Oct—16) In house check: Oct—17 Name Function Signature es Calibrated by: Michael Weber Laboratory Technician Approved by: KatJa Pokovic Technical Manager Issued: November 25, 2016 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: ER3—2476_Nov16 Page 1 of 10

Calibration 6 Laboratory of a$y \// *z Schweizerischer Kalibrierdienst Schmid & Partner il_a\eigm Service suisse d‘étalonnage Englneerlng AG ;///_%\? Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland 7 o4 eakkG O Swiss Calibration Service //”/nln\\‘\\ Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: NORMx,y,z sensitivity in free space DCP diode compression point CF crest factor (1/duty_cycle) of the RF signal A, B, C, D modulation dependent linearization parameters Polarization q @ rotation around probe axis Polarization 8 8 rotation around an axis that is in the plane normal to probe axis (at measurement center), i.e., 8 = 0 is normal to probe axis Connector Angle information used in DASY system to align probe sensor X to the robot coordinate system Calibration is Performed According to the Following Standards: a) IEEE Std 1309—2005, " IEEE Standard for calibration of electromagnetic field sensors and probes, excluding antennas, from 9 kHz to 40 GHz", December 2005 b) CTIA Test Plan for Hearing Aid Compatibility, Rev 3.0, November 2013 Methods Applied and Interpretation of Parameters: NORMx,y,z: Assessed for E—field polarization 8 = 0 for XY sensors and 8 = 90 for Z sensor (f < 900 MHz in TEM—cell; f > 1800 MHz: R22 waveguide). NORM(F)x,y,z = NORMx,y,z * frequency_response (see Frequency Response Chart). DCPx,y,z: DCP are numerical linearization parameters assessed based on the data of power sweep with CW signal (no uncertainty required). DCP does not depend on frequency nor media. PAR: PAR is the Peak to Average Ratio that is not calibrated but determined based on the signal characteristics Ax,y,z; Bx,y,z; Cx,y,z; Dx,y,z; VRx,y,z: A, B, C, D are numerical linearization parameters assessed based on the data of power sweep for specific modulation signal. The parameters do not depend on frequency nor media. VR is the maximum calibration range expressed in RMS voltage across the diode. Spherical isotropy (3D deviation from isotropy): in a locally homogeneous field realized using an open waveguide setup. Sensor Offset: The sensor offset corresponds to the offset of virtual measurement center from the probe tip (on probe axis). No tolerance required. Connector Angle: The angle is assessed using the information gained by determining the NORMx (no uncertainty required). Certificate No: ER3—2476_Nov16 Page 2 of 10

ER3DV6 — SN:2476 November 23, 2016 Probe ER3DVG SN:2476 Manufactured: March 31, 2009 Calibrated: November 23, 2016 Calibrated for DASY/EASY Systems (Note: non—compatible with DASY2 system!) Certificate No: ER3—2476_Nov16 Page 3 of 10

ER3DV6 — SN:2476 November 23, 2016 DASY/EASY — Parameters of Probe: ER3DVG6 — SN:2476 Basic Calibration Parameters Sensor X Sensor Y Sensor Z Unc (k=2) Norm (pV/(V/m)z) 1.87 1.64 2.16 + 10.1 % DCP (mVv)® 99.9 100.2 101.5 Modulation Calibration Parameters UID Communication System Name A B C D VR Unc E dB dBVuV dB mV (k=2) 0 CW x 0.0 0.0 1.0 0.00 183.4 +3.3 % y 0.0 0.0 1.0 208.3 2 0.0 0.0 1.0 231.9 10011— UMTS—FDD (WCDMA) x 3.33 67.4 19.0 2.91 149.1 +0.7 % CAB Y 3.26 67.0 18.9 125.3 Z 3.27 67.3 19.1 140.4 10021— GSM—FDD (TDMA, GMSK) xX 17.50 100.0 28.4 9.39 137.1 £1.7 % DAC Y 16.60 99.2 28.5 115.1 Z7 22.35 99.5 29.0 112.3 10039— CDMA2000 (1xRTT, RC1) X 4.65 66.5 19.1 4.57 111.6 +0.9% CAB y 4.75 66.7 19.3 128.0 Z 4.83 67.3 19.6 143.5 10081— CDMA2000 (1xRTT, RC3) X 3.99 66.6 19.1 3.97 148.4 +0.7 % CAB Y 3.93 66.2 18.9 123.3 Z 3.95 66.6 19.1 137.5 10295— CDMA2000, RC1, SO3, 1/8th Rate 25 fr. x 14.10 99.6 41.9 1249 86.6 £1.9 % AAB ¥ 13.03 95.0 39.3 101.1 Z 18.07 99.9 39.6 93.9 The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. ® Numerical linearization parameter: uncertainty not required. & Uncertainty is determined using the max. deviation from linear response applying rectangular distribution and is expressed for the square of the field value. Certificate No: ER3—2476_Nov16 Page 4 of 10


Document Created: 2017-12-04 19:07:50
Document Modified: 2017-12-04 19:07:50
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC