test report

FCC ID: WRMRFH630

Test Report

Download: PDF
FCCID_1798244

Test report no. 12007932 Page 1 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 Test Report acc. to FCC Title 47 CFR Part 15 relating to Sick AG RFH630 Title 47 - Telecommunication Part 15 - Radio Frequency Devices Subpart C – Intentional Radiators Measurement Procedure: ANSI C63.4-2009 Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 2 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 Manufacturer’s details Manufacturer Sick AG Manufacturer’s grantee code --- Manufacturer’s address Sick AG Merkurring 20 22143 Hamburg Germany Phone: + 49 (0) 40 611680-246 Fax: + 49 (0) 40 611680-201 Email: jan.potthast@sick.de Relevant standard used 47 CFR Part 15C - Intentional Radiators ANSI C63.4-2009 Test Report prepared by Technical engineer Ralf Trepper m. dudde hochfrequenz-technik (laboratory) Rottland 5a 51429 Bergisch Gladbach Germany Phone: +49 2207 96890 Fax: +49 2207 968920 Email: m.duddelabor@dudde.com Equipment Under Test (EUT) Equipment category Inductive application / RFID Trade name Sick Type designation RFH630 Serial no. 11 24 0005 Variants --- Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 3 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 1. Test results Clause Requirements headline Test result Report page number 8.1 Antenna Requirement Pass Fail N.t.* 9 8.2 Restricted bands of operation Pass Fail N.t.* 10 to 11 8.3 Conducted limits Pass Fail N.t.* 12 to 15 8.4 Radiated emission limits Pass Fail N.t.* 16 to 22 8.5 Frequency tolerance Pass Fail N.t.* 23 to 25 * Not tested The equipment meets the requirements Yes No Signature: ............................. Signature: ............................. (Technician) (Manager) Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 4 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 Table of contents 1. Test results........................................................................................................................................................ 3 2. Introduction ...................................................................................................................................................... 5 3. Testing laboratory ............................................................................................................................................ 5 4. Applicant .......................................................................................................................................................... 6 5. Product and product documentation ................................................................................................................ 6 6. Conclusions, observations and comments ....................................................................................................... 7 7. Operational description ..................................................................................................................................... 8 8. Compliance assessment .................................................................................................................................... 9 8.1 Antenna requirement ...................................................................................................................................... 9 8.1.1 Regulation ............................................................................................................................................. 9 8.1.2 Result .................................................................................................................................................... 9 8.2 Restricted bands of operation ........................................................................................................................ 10 8.2.1 Regulation ............................................................................................................................................. 10 8.2.2 Result .................................................................................................................................................... 11 8.3 Conducted limits ............................................................................................................................................ 12 8.3.1 Regulation ............................................................................................................................................. 12 8.3.2 Test equipment ..................................................................................................................................... 13 8.3.3 Test procedures ..................................................................................................................................... 13 8.3.4 Result .................................................................................................................................................... 14 8.4 Radiated emission limits ................................................................................................................................ 16 8.4.1 Regulation ............................................................................................................................................. 16 8.4.2 Test equipment ..................................................................................................................................... 17 8.4.3 Test procedure ...................................................................................................................................... 18 8.4.4 Calculation of the field strength ........................................................................................................... 19 8.4.5 Result .................................................................................................................................................... 20 8.5 Frequency tolerance ....................................................................................................................................... 23 8.5.1 Regulation ............................................................................................................................................. 23 8.5.2 Test equipment ..................................................................................................................................... 23 11.5.3 Test procedures ................................................................................................................................... 24 8.5.4 Result .................................................................................................................................................... 26 9. Additional information to the test report ......................................................................................................... 27 Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 5 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 2. Introduction This test report consists of:  Test result summary  List of contents  Introduction and further information  Performance assessment  Detailed test information All pages have been numbered consecutively and bear the m. dudde hochfrequenz-technik logo, the test report number, the date, the test specification in its current version as well as the type designation of the EUT. The total number of pages in this report is 30. The tests were carried out at: - m. dudde hochfrequenz-technik, D-51429 Bergisch Gladbach in a representative assembly and in accordance with the test methods and/or requirements stated in: FCC Title 47 CFR Part 15 Subpart C & ANSI C63.4-2009 The sample of the product was received on: - 2012-02-14 The tests were carried out in the following period of time: - 2012-02-14 – 2012-03-08 3. Testing laboratory m. dudde hochfrequenz-technik Rottland 5a, 51429 Bergisch Gladbach, Germany Phone: +49 - (0) 22 07 / 96 89-0 Fax: +49 - (0) 22 07 / 96 89-20 - FCC Registration Number: 699717 Accredited by: DAkkS Deutsche Akkreditierungsstelle GmbH DAkkS accreditation number: D-PL-12053-01 Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 6 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 4. Applicant Company name : Sick AG Address : Merkurring 20 22143 Hamburg Country : Germany Telephone : + 49 (0) 40 611680-246 Fax : + 49 (0) 40 611680-201 Email : jan.potthast@sick.de Date of order : 2012-02-28 References : Mr. Jan Potthast 5. Product and product documentation Samples of the following apparatus were submitted for testing: Manufacturer : Sick AG Trademark : Sick Type designation : RFH630 Hardware version : RFH630 Serial number : --- Software release : --- Type of equipment : Transceiver Power used : 24.0 V DC Frequency used : 13.560 MHz Generated frequencies : 13.560 MHz Carrier ITU emission class : 608H A1D Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 7 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 For issuing this report the following product documentation was used: Description Date Identifications External photographs of the Equipment Under Test (EUT) 2012-03-12 Annex no. 1 Internal photographs of the Equipment Under Test (EUT) 2012-03-12 Annex no. 2 Channel occupancy / bandwidth 2012-03-12 Annex no. 3 Label sample 2012-03-12 Annex no. 4 Functional description / User manual 2012-03-12 Annex no. 5 Test setup photos 2012-03-12 Annex no. 6 Block diagram 2012-03-12 Annex no. 7 Operational description 2012-03-12 Annex no. 8 Schematics 2012-03-12 Annex no. 9 Parts list 2012-03-12 Annex no. 10 Antenna characteristics / Antenna description 2012-03-12 Annex no. 11 6. Conclusions, observations and comments The test report will be filed at m. dudde hochfrequenz-technik for a period of 10 years following the issue of this report. It may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of m. dudde hochfrequenz-technik. The results of the tests as stated in this report are exclusively applicable to the EUT as identified in this report. m. dudde hochfrequenz-technik cannot be held liable for properties of the EUT that have not been observed during these tests. m. dudde hochfrequenz-technik assumes the sample to comply with the requirements of FCC Title 47 CFR Part 15 for the respective test sector, if the test results turn out positive. Comments: --- Date : 2012-03-12 Date : 2012-03-12 Name : Ralf Trepper Name : Manfried Dudde Function : Technician Function : Manager Signature : …………………. Signature : ………………… Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 8 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 7. Operational description 7.1 EUT details RFID Reader System works at a frequency of 13.560 MHz. It comprises a reader, one antenna and transponder (for example: smart label) and is used for wireless identification of a variety of objects. 7.2 EUT configurations See test setup photographs! 7.3 EUT measurement description Radiated measurements The RFH630was tested in a typical fashion with the combinations described in 7.2. During preliminary emission tests the RFH630was operated in the continuous transmitting mode for worst case emission mode investigation. Therefore, the final qualification testing was completed with RFH630operated in continuous modes. All tests were performed with the applicant’s declared nominal voltage of 24.0 V DC. In order to establish the maximum radiation, firstly, there have been viewed all orthogonal adjustments of the test samples, secondly the test ample have been rotated at all adjustments around the own axis between 0° and 360°, and thirdly, the antenna polarization between horizontal and vertical had been varied. Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 9 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 8. Compliance assessment 8.1 Antenna requirement 8.1.1 Regulation An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this Section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. This requirement does not apply to carrier current devices or to devices operated under the provisions of Sections 15.211, 15.213, 15.217, 15.219, or 15.221. Further, this requirement does not apply to intentional radiators that must be professionally installed, such as perimeter protection systems and some field disturbance sensors, or to other intentional radiators which, in accordance with Section 15.31(d), must be measured at the installation site. However, the installer shall be responsible for ensuring that the proper antenna is employed so that the limits in this Part are not exceeded. 8.1.2 Result The equipment meets the requirements Yes * No N.t. Further test results are attached Yes No Page no. Integrated loop coil antenna and external loop coil antenna (RFA332) N.t.* See page no. 27 Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 10 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 8.2 Restricted bands of operation 8.2.1 Regulation (a) Except as shown in paragraph (d) of this section, only spurious emissions are permitted in any of the frequency bands listed below: MHz MHz MHz GHz 0.090 - 0.110 16.42 - 16.423 399.9 - 410 4.5 - 5.15 1 0.495 - 0.505 16.69475 - 16.69525 608 - 614 5.35 - 5.46 2.1735 - 2.1905 16.80425 - 16.80475 960 - 1240 7.25 - 7.75 4.125 - 4.128 25.5 - 25.67 1300 - 1427 8.025 - 8.5 4.17725 - 4.17775 37.5 - 38.25 1435 - 1626.5 9.0 - 9.2 4.20725 - 4.20775 73 - 74.6 1645.5 - 1646.5 9.3 - 9.5 6.215 - 6.218 74.8 - 75.2 1660 - 1710 10.6 - 12.7 6.26775 - 6.26825 108 - 121.94 1718.8 - 1722.2 13.25 - 13.4 6.31175 - 6.31225 123 - 138 2200 - 2300 14.47 - 14.5 8.291 - 8.294 149.9 - 150.05 2310 - 2390 15.35 - 16.2 8.362 - 8.366 156.52475 - 156.52525 2483.5 - 2500 17.7 - 21.4 8.37625 - 8.38675 156.7 - 156.9 2690 - 2900 22.01 - 23.12 8.41425 - 8.41475 162.0125 - 167.17 3260 - 3267 23.6 - 24.0 12.29 - 12.293 167.72 - 173.2 3332 - 3339 31.2 - 31.8 12.51975 - 12.52025 240 - 285 3345.8 - 3358 36.43 - 36.5 12.57675 - 12.57725 322 - 335.4 3600 - 4400 (2) 13.36 - 13.41 1 Until February 1, 1999, this restricted band shall be 0.490-0.510 MHz 2 Above 38.6 (b) Except as provided in paragraphs (d) and (e), the field strength of emissions appearing within these frequency bands shall not exceed the limits shown in Section 15.209. At frequencies equal to or less than 1000 MHz, compliance with the limits in Section 15.209 shall be demonstrated using measurement instrumentation employing a CISPR quasi-peak detector. Above 1000 MHz, compliance with the emission limits in Section 15.209 shall be demonstrated based on the average value of the measured emissions. The provisions in Section 15.35 apply to these measurements. (c) Except as provided in paragraphs (d) and (e), regardless of the field strength limits specified elsewhere in this Subpart, the provisions of this Section apply to emissions from any intentional radiator. Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 11 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 (d) The following devices are exempt from the requirements of this Section: (1) Swept frequency field disturbance sensors operating between 1.705 and 37 MHz provided their emissions only sweep through the bands listed in paragraph (a), the sweep is never stopped with the fundamental emission within the bands listed in paragraph (a), and the fundamental emission is outside of the bands listed in paragraph (a) more than 99% of the time the device is actively transmitting, without compensation for duty cycle. (2) Transmitters used to detect buried electronic markers at 101.4 kHz which are employed by telephone companies. (3) Cable locating equipment operated pursuant to Section 15.213. (4) Any equipment operated under the provisions of § 15.253, § 15.255 or § 15.257 of this part. (5) Biomedical telemetry devices operating under the provisions of Section 15.242 of this part are not subject to the restricted band 608-614 MHz but are subject to compliance within the other restricted bands. (6) Transmitters operating under the provisions of Subpart D or F of this part. (7) Devices operated pursuant to § 15.225 are exempt from complying with this section for the 13.36- 13.41 MHz band only. (8) Devices operated in the 24.075-24.175 GHz band under § 15.245 are exempt from complying with the requirements of this section for the 48.15-48.35 GHz and 72.225-72.525 GHz bands only, and shall not exceed the limits specified in § 15.245(b). (9) Devices operated in the 24.0-24.25 GHz band under § 15.249 are exempt from complying with the requirements of this section for the 48.0-48.5 GHz and 72.0-72.75 GHz bands only, and shall not exceed the limits specified in § 15.249(a). (e) Harmonic emissions appearing in the restricted bands above 17.7 GHz from field disturbance sensors operating under the provisions of Section 15.245 shall not exceed the limits specified in Section 15.245(b). 8.2.2 Result The equipment meets the requirements Yes No N.t. Further test results are attached Yes No Page no. N.t.* See page no. 27 Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 12 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 8.3 Conducted limits 8.3.1 Regulation (a) For an intentional radiator which is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies within the band 150 kHz to 30 MHz shall not exceed the limits in the following table, as measured using a 50µH/50ohms line impedance stabilization network (LISN). Compliance with this provision of this paragraph shall be based on the measurement of the radio frequency voltage between each power line and ground at the power terminal. The lower limit applies at the boundary between the frequency ranges. Frequency of emission(MHz) Conducted limit (dBµV) Quasi-peak Average 0.15-0.50 66 to 56* 56 to 46* 0.50-5.0 56 46 5.0-30.0 60 50 * Decreases with the logarithm of the frequency (c) Measurements to demonstrate compliance with the conducted limits are not required for devices which only employ battery power for operation and which do not operate from the AC power lines or contain provisions for operation while connected to the AC power lines. Devices that include, or make provision for, the use of battery chargers which permit operating while charging, AC adaptors or battery eliminators or connected to the AC power lines indirectly, obtaining their power through another device which is connected to the AC power lines, shall be tested to demonstrate compliance with the conducted limits. Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 13 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 8.3.2 Test equipment Manufacturer/ Last Next Calibration Type Serial no. Model no. calibration calibration executed by Receiver Schwarzbeck 1518294 08/2010 08/2013 --- (9 kHz - 30MHz) FMLK 1518 (428) 9360 Panorama- Monitor PAZ1550 (429) --- --- --- --- FMLK / VUMA Protector limiter Rhode & Schwarz 357,881052 09/2011 09/2013 Dudde 9 kHz - 30MHz 10 dB ESH 3Z2 (272) V-LISN 50 RFT 13835240 07/2010 07/2013 Dudde ohms//(50 uH+5 ohms) NNB 11 (72) V-LISN 50 EMCO 9512-1227 07/2011 07/2014 Dudde ohms//(50 uH+5 ohms) (49b) Heiden Power supply 005504 08/2012 08/2014 Dudde Type:1108-32 RF- cable Aircell 1.5m [BNC/N] K30 09/2011 09/2012 Dudde 8.3.3 Test procedures The EUT and the additional equipment (if required) are connected to the main power through a line impedance stabilization network (LISN). The LISN must be appropriate to ANSI C63.4-2009 Section 7. Additional equipment must also be connected to a second LISN with the same specifications described in the above sentence (if required). Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 14 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 8.3.4 Result Tested with external AC/DC power supply CONDUCTED EMISSIONS (Section 15.207) Tested Emission Receiver Result Spec. limit Margin Remarks line frequency bandwidth quasi-peak (average) [MHz] [kHz] [dBµV] [dBµV] [dB] L1 0.181 9 -2 55.8 57.8 *2 N 0.181 9 -2 55.8 57.8 *2 L1 0.301 9 -2 51.7 53.7 *2 N 0.301 9 -2 51.7 53.2 *2 L1 0.475 9 -2 47 49.0 *1 N 0.475 9 -2 47 49.0 *1 L1 0.600 9 -2 46 48.0 *1 N 0.600 9 -2 46 48.0 *1 L1 0.775 9 -2 46 48.0 *2 N 0.775 9 -2 46 48.0 *2 L1 0.850 9 -2 46 48.0 *1 N 0.850 9 -2 46 48.0 *1 L1 1.000 9 -2 46 48.0 *1 N 1.000 9 -2 46 48.0 *1 L1 1.254 9 -2 46 48.0 *2 N 1.254 9 -2 46 48.0 *2 L1 2.000 9 -2 46 48.0 *1 N 2.000 9 -2 46 48.0 *1 L1 4.356 9 28.0 46 18 *2 N 4.356 9 25.0 46 21 *2 L1 6.7644 9 -2 50 52.0 *1 N 6.7644 9 -2 50 52.0 *1 L1 13.560 9 46.5 50 3.5 *2 N 13.560 9 48.0 50 2.0 *2 L1 20.2931 9 -2 50 52.0 *1 N 20.2931 9 -2 50 52.0 *1 L1 27.119 9 26.0 50 24.0 *2 N 27.119 9 29.0 50 21.0 *2 Remark: * Noise level of the measuring instrument ≤ -2dBµV (0.009 – 30MHz) 1 Remark: *2 Quasi peak measurements lower than “Specified Average Limit” The equipment meets the requirements Yes No N.t. Further test results are attached Yes No Page no. N.t.* See page no. 27 Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 15 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 Tested with Laptop over LAN- port CONDUCTED EMISSIONS (Section 15.207) Tested Emission Receiver Result Spec. limit Margin Remarks line frequency bandwidth quasi-peak (average) [MHz] [kHz] [dBµV] [dBµV] [dB] L1 0.1960 9 44.0 55.3 11.3 *2 N 0.1960 9 44.0 55.3 11.3 *2 L1 0.301 9 -2 51.7 53.7 *1 N 0.301 9 -2 51.7 53.2 *1 L1 0.475 9 -2 47 49.0 *1 N 0.475 9 -2 47 49.0 *1 L1 0.600 9 -2 46 48.0 *1 N 0.600 9 -2 46 48.0 *1 L1 0.775 9 -2 46 48.0 *2 N 0.775 9 -2 46 48.0 *2 L1 0.850 9 -2 46 48.0 *1 N 0.850 9 -2 46 48.0 *1 L1 1.000 9 -2 46 48.0 *1 N 1.000 9 -2 46 48.0 *1 L1 1.787 9 29.0 46 17.0 *2 N 1.787 9 29.0 46 17.0 *2 L1 2.084 9 29.5 46 16.5 *2 N 2.084 9 29.5 46 16.5 *2 L1 2.423 9 25.0 46 21.0 *2 N 2.423 9 25.0 46 21.0 *2 L1 6.7644 9 -2 50 52.0 *1 N 6.7644 9 -2 50 52.0 *1 L1 13.5288 9 -2 50 52.0 *1 N 13.5288 9 -2 50 52.0 *1 L1 20.2931 9 -2 50 52.0 *1 N 20.2931 9 -2 50 52.0 *1 L1 27.0575 9 -2 50 52.0 *1 N 27.0575 9 -2 50 52.0 *1 Remark: * Noise level of the measuring instrument ≤ -2dBµV (0.009 – 30MHz) 1 Remark: *2 Quasi peak measurements lower than “Specified Average Limit” The equipment meets the requirements Yes No N.t. Further test results are attached Yes No Page no. N.t.* See page no. 27 Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 16 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 8.4 Radiated emission limits 8.4.1 Regulation (a) Except as provided elsewhere in this subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table: Frequency Field Strength Measurement distance (MHz) (microvolts/meter) (meters) 0.009-0.490 2400/F(kHz) 300 0.490-1.705 24000/F(kHz) 30 1.705-30.0 30 30 30-88 100 3 88-216 150 3 216-960 200 3 Above 960 500 3 (b) In the emission table above, the tighter limit applies at the band edges. (c) The level of any unwanted emissions from an intentional radiator operating under these general provisions shall not exceed the level of the fundamental emission. For intentional radiators which operate under the provisions of other sections within this part and which are required to reduce their unwanted emissions to the limits specified in this table, the limits in this table are based on the frequency of the unwanted emission and not the fundamental frequency. However, the level of any unwanted emissions shall not exceed the level of the fundamental frequency. (d) The emission limits shown in the above table are based on measurements employing a CISPR quasi peak detector except for the frequency bands 9-90 kHz, 110-490 kHz and above 1000 MHz. Radiated emission limits in these three bands are based on measurements employing an average detector. (e) The provisions in §§ 15.31, 15.33, and 15.35 for measuring emissions at distances other than the distances specified in the above table, determining the frequency range over which radiated emissions are to be measured, and limiting peak emissions apply to all devices operated under this part. (f) In accordance with Section 15.33(a), in some cases the emissions from an intentional radiator must be measured to beyond the tenth harmonic of the highest fundamental frequency designed to be emitted by the intentional radiator because of the incorporation of a digital device. lf measurements above the tenth harmonic are so required, the radiated emissions above the tenth harmonic shall comply with the general radiated emission limits applicable to the incorporated digital device, as shown in Section 15.109 and as based on the frequency of the emission being measured, or, except for emissions contained in the restricted frequency bands shown in Section 15.205, the limit on spurious emissions specified for the intentional radiator, whichever is the higher limit. Emissions which must be measured above the tenth harmonic of the highest fundamental frequency designed to be emitted by the intentional radiator and which fall within the restricted bands shall comply with the general radiated emission limits in Section 15.109 that are applicable to the incorporated digital device. Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 17 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 8.4.2 Test equipment Manufacturer/ Last Next Calibration Type Serial no. Model no. calibration calibration executed by OATS Dudde (104) --- 08/2010 08/2012 Dudde Digital Multimeter GW GDM-8045G (144) 0090256 08/2011 08/2014 Dudde Rohde & Schwarz Receiver Rohde & Spectrum Analyzer 100.117 11/2010 11/2012 (9 kHz –18.0 GHz) Schwarz FSL 18 (171a) Pre-amplifier Hewlett Packard 1726A00705 01/2012 01/2014 Dudde (100kHz - 1.3GHz) 8447 E (166a) Pre-amplifier Narda --- 01/2012 01/2014 Dudde (1GHz - 18GHz) --- (345) Magnetic loop antenna Schwarzbeck --- 05/2010 05/2013 Dudde (9 kHz - 30 MHz) FMZB 1516 (23) Bilog-antenna Schwarzbeck --- 04/2011 04/2014 Schwazbeck (30- 1000 MHz) VULP 9168 (406) Hornantenna Schwarzbeck 236 03/2011 03/2013 Dudde (0.86-8.5 GHz) BBHA 9120 A (284) Hornantenna Schwarzbeck 305 03/2011 03/2013 Dudde (2.0-14.0 GHz) BBHA 9120 C (169) RF- cable Kabelmetal 18m [N] K1 09/2011 09/2012 Dudde RF- cable Aircell 0.5m [BNC] K40 09/2011 09/2012 Dudde Sucoflex 100 Suhner RF- cable K52 09/2011 09/2012 Dudde 1 m [N] RF- cable Aircell 1m [BNC/N] K56 09/2011 09/2012 Dudde Sucoflex 100 Suhner RF- cable K61 09/2011 09/2012 Dudde 1 m [N] ( Sucoflex 106 Suhner 6,4m RF- cable K74 09/2011 09/2012 Dudde [N] Sucoflex 106 Suhner 6,4m RF- cable K75 09/2011 09/2012 Dudde [N] Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 18 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 8.4.3 Test procedure The EUT and this peripheral (when additional equipment exists) are placed on a turn table which is 0.8 m above the ground. The turn table would be allowed to rotate 360 degrees to determine the position of the maximum emission level. The test distance between the EUT and the receiving antenna are 3m. To find the maximum emission, the polarization of the receiving antenna is changed in horizontal and vertical polarization; the position of the EUT was changed in different orthogonal determinations. ANSI C63.4-2009 Section 8 “Radiated Emissions Testing” Measurement procedures for electric field radiated emissions above 1 GHz are covered in Clause 8 of ANSI C63.4-2009. The ANSI C63.4-2009 measurement procedure consists of both an exploratory test and a final measurement. The exploratory test is critical to determine the frequency of all significant emissions. For each mode of operation required to be tested, the frequency spectrum is monitored. Variations in antenna height, antenna orientation, antenna polarization, EUT azimuth, and cable or wire placement is explored to produce the emission that has the highest amplitude relative to the limit. The final measurements are made based on the findings in the exploratory testing. When making exploratory and final measurements it is necessary to maximize the measured radiated emission. Subclause 8.3.1.2 of ANSI C63.4- 2009 states that the measurement is to be made “while keeping the antenna in the ‘cone of radiation’ from that area and pointed at the area both in azimuth and elevation, with polarization oriented for maximum response.” We consider the “cone of radiation” to be the 3 dB beam width of the measurement antenna. While the “bore-sighting” technique is not explicitly mentioned in ANSI C63.4-2009, it is a useful technique for measurements using a directional antenna, such as a double-ridged waveguide antenna. Several precautions must be observed, including: knowledge of the beam width of the antenna and the resulting illumination area relative to the size of the EUT, estimation for source of the emission and general location within larger EUTS, measuring system sensitivity, etc. ANSI C63.4-2009 requires that the measurement antenna is kept pointed at the source of the emission both in azimuth and elevation, with the polarization of the antenna oriented for maximum response. That means that if the directional radiation pattern of the EUT results in a maximum emission at an upwards angle from the EUT, when a directional antenna is used to make the measurement it will be necessary for it to be pointed towards the source of the emission within the EUT. This can be done by either pointing the antenna at an angle towards the source of the emission, or by rotating the EUT, in both height and polarization, to maximize the measured emission. The emission must be kept within the illumination area of the 3 dB beamwidth of the antenna so that the maximum emission from the EUT is measured. Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 19 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 Radiated emissions test characteristics Frequency range 0.009 MHz - 4,000 MHz Test distance 10m, 3 m* Test instrumentation resolution bandwidth 9 kHz (9 kHz – 30 MHz) 120 kHz (30 MHz - 1,000 MHz) 1 MHz (1000 MHz - 4,000 MHz) Receive antenna scan height 1m-4m Receive antenna polarization Vertical/horizontal * According to Section 15.31 (f) (1): At frequencies at or above 30 MHz, measurements may be performed at a distance other than what is specified provided: measurements are not made in the near field except where it can be shown that near field measurements are appropriate due to the characteristics of the device; and it can be demonstrated that the signal levels needed to be measured at the distance employed can be detected by the measurement equipment. When performing measurements at a distance other than that specified, the results shall be extrapolated to the specified distance using an extrapolation factor of 20dB/decade (inverse linear-distance for field strength measurements; inverse-linear-distance-squared for power density measurements). 8.4.4 Calculation of the field strength The field strength is calculated by the following calculation: Corrected Level = Receiver Level + Correction Factor (without the use of a pre-amplifier) Corrected Level = Receiver Level + Correction Factor – Pre-amplifier (with the use of a pre-amplifier) Receiver Level : Receiver reading without correction factors Correction Factor : Antenna factor + cable loss For example: The receiver reading is 32.7 dBµV. The antenna factor for the measured frequency is +2.5 dB (1/m) and the cable factor for the measured frequency is 0.71 dB, giving a field strength of 35.91dBµV/m. The 35.91dBµV/m value can be mathematically converted to its corresponding level in µV/m. Level in µV/m = Common Antilogarithm (35.91/20) = 39.8 For test distance other than what is specified, but fulfilling the requirements of Section 15.31 (f) (1) the field strength is calculated by adding additionally an extrapolation factor of 20 dB/decade (inverse linear distance for field strength measurements). Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 20 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 8.4.5 Result RFH630 in combination with the internal antenna FUNDAMENTAL EMISSION & HARMONICS (Section 15.225) Polaris. f Bandwidth Noted Test Correction Distance Level Limit Margin EUT (MHz) (kHz), receiver distance factor extrapol. corrected / Type level factor antenna of detector m dB dB dBµV/m dBµV/m dBµV/m orientation dBµV @ meter height/cm 13.560 QPK/9kHz 54.8 10 20.2 -19.1 55.9 84.0 @ 30 28.1 V 0° 100 40.680 QPK/120kHz 22.3 3 -7.0 0 14.9 40.0 @ 3 25.1 V 210°/H 121 67.800 QPK/120kHz 28.1 3 -10.0 0 18.8 40.0 @ 3 21.2 V 30°/H 216 122.040 QPK/120kHz 25.2 3 -8.2 0 17.0 43.5 @ 3 26.5 V 30°/H 170 135.600 QPK/120kHz 30.3 3 -7.4 0 22.9 43.5 @ 3 20.6 V 30°/H 133 149.160 QPK/120kHz 32.8 3 -6.6 0 26.2 43.5 @ 3 17.3 V 30°/H 186 162.720 QPK/120kHz 37.7 3 -6.6 0 31.1 43.5 @ 3 12.4 V 90°/H 186 176.280 QPK/120kHz 33.3 3 -8.3 0 25.0 43.5 @ 3 18.5 V 90°/H 157 189.840 QPK/120kHz 35.8 3 -10.0 0 25.8 43.5 @ 3 17.7 V 90°/H 181 203.400 QPK/120kHz 33.4 3 -10.4 0 23.0 43.5 @ 3 50.5 V 90°/H 154 216.960 QPK/120kHz 36.8 3 -9.4 0 27.4 43.5 @ 3 16.1 V 70°/H 135 230.520 QPK/120kHz 35.9 3 -8.7 0 27.2 43.5 @ 3 16.3 V 70°/H 134 244.080 QPK/120kHz 37.1 3 -8.6 0 28.5 43.5 @ 3 15.0 V 70°/H 136 257.630 QPK/120kHz 32.8 3 -8.1 0 24.7 43.5 @ 3 18.8 V 70°/H 105 271.200 QPK/120kHz 33.2 3 -7.5 0 25.7 46.0 @ 3 20.3 V 70°/H 113 325.450 QPK/120kHz 37.8 3 -6.0 0 31.8 46.0 @ 3 14.2 V 70°/H 124 Measurement uncertainty 4 dB Blue marked: restricted bands Bandwidth = the measuring receiver bandwidth Remark: *1 noise floor noise level of the measuring instrument ≤ 4.0dBµV @ 10m distance (0.009 – 30 MHz) Remark: *2 noise floor noise level of the measuring instrument ≤ 6.5dBµV @ 3m distance (30 – 1,000 MHz) Remark: *3 noise floor noise level of the measuring instrument ≤ 10 dBµV @ 3m distance (1,000 – 2,000 MHz) Remark: *4 noise floor noise level of the measuring instrument ≤ 17 dBµV @ 3m distance (2,000 – 5,500 MHz) Remark: *5 for using a pre-amplifier in the range between 100 kHz and 1,000 MHz The equipment meets the requirements Yes No N.t. Further test results are attached Yes No Page no. 28 N.t.* See page no. 27 Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 21 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 RFH630 in combination with the internal antenna continued FUNDAMENTAL EMISSION & HARMONICS (Section 15.225) Polaris. f Bandwidth Noted Test Correction Distance Level Limit Margin EUT (MHz) (kHz), receiver distance factor extrapol. corrected / Type level factor antenna of detector m dB dB dBµV/m dBµV/m dBµV/m orientation dBµV @ meter height/cm 339.000 QPK/120kHz 36.9 3 -5.9 0 31.0 46.0 @ 3 15.0 V 70°/H 126 352.560 QPK/120kHz 40.04 3 -5.0 0 35.4 46.0 @ 3 10.6 V 70°/H 256 366.120 QPK/120kHz 43.0 3 -5.2 0 37.8 46.0 @ 3 8.2 V 70°/H 200 420.350 QPK/120kHz 33.9 3 -4.6 0 29.3 46.0 @ 3 16.7 V 60°/H 100 637.320 QPK/120kHz 35.4 3 -0.8 0 34.6 46.0 @ 3 11.4 V 60°/H 154 650.850 QPK/120kHz 32.9 3 -0.9 0 32.0 46.0 @ 3 14.0 V 90°/H 164 827.150 QPK/120kHz 27.7 3 +2.5 0 30.2 46.0 @ 3 15.8 V 90°/H 100 867.850 QPK/120kHz 31.7 3 +3.1 0 34.8 46.0 @ 3 11.2 V 90°/H 100 894.950 QPK/120kHz 33.6 3 +4.1 0 37.7 46.0 @ 3 8.3 V 80°/H 100 Measurement uncertainty 4 dB Blue marked: restricted bands Bandwidth = the measuring receiver bandwidth Remark: *1 noise floor noise level of the measuring instrument ≤ 4.0dBµV @ 10m distance (0.009 – 30 MHz) Remark: *2 noise floor noise level of the measuring instrument ≤ 6.5dBµV @ 3m distance (30 – 1,000 MHz) Remark: *3 noise floor noise level of the measuring instrument ≤ 10 dBµV @ 3m distance (1,000 – 2,000 MHz) Remark: *4 noise floor noise level of the measuring instrument ≤ 17 dBµV @ 3m distance (2,000 – 5,500 MHz) Remark: *5 for using a pre-amplifier in the range between 100 kHz and 1,000 MHz The equipment meets the requirements Yes No N.t. Further test results are attached Yes No Page no. 28 N.t.* See page no. 27 Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 22 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 RFH630 in combination with the external antenna RFA332 FUNDAMENTAL EMISSION & HARMONICS (Section 15.225) Polaris. f Bandwidth Noted Test Correction Distance Level Limit Margin EUT (MHz) (kHz), receiver distance factor extrapol. corrected / Type level factor antenna of detector m dB dB dBµV/m dBµV/m dBµV/m orientation dBµV @ meter height/cm 13.560 QPK/9kHz 67.0 10 20.2 -19.1 68.1 84.0 @ 30 15.9 V 0° 100 27.120 QPK/9kHz 17.9 10 20.2 -19.1 19.0 29.5 @ 30 10.5 V 90° 100 122.040 QPK/120kHz 21.1 3 -8.2 0 12.9 43.5 @ 3 30.6 V 0°/V 100 162.720 QPK/120kHz 24.1 3 -6.6 0 17.5 43.5 @ 3 26.0 V 60°/H 204 Measurement uncertainty 4 dB Blue marked: restricted bands Bandwidth = the measuring receiver bandwidth Remark: *1 noise floor noise level of the measuring instrument ≤ 4.0dBµV @ 10m distance (0.009 – 30 MHz) Remark: *2 noise floor noise level of the measuring instrument ≤ 6.5dBµV @ 3m distance (30 – 1,000 MHz) Remark: *3 noise floor noise level of the measuring instrument ≤ 10 dBµV @ 3m distance (1,000 – 2,000 MHz) Remark: *4 noise floor noise level of the measuring instrument ≤ 17 dBµV @ 3m distance (2,000 – 5,500 MHz) Remark: *5 for using a pre-amplifier in the range between 100 kHz and 1,000 MHz The equipment meets the requirements Yes No N.t. Further test results are attached Yes No Page no. 29 N.t.* See page no. 27 Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 23 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 8.5 Frequency tolerance 8.5.1 Regulation (e) The frequency tolerance of the carrier signal shall be maintained within ± 0.01 % of the operating frequency over a temperature variation of -20 °C to +55 °C at normal supply voltage, and for a variation in the primary supply voltage from 85 % to 115 % of the rated supply voltage at a temperature of 20 °C. 8.5.2 Test equipment Manufacturer/ Last Next Calibration Type Serial no. Model no. calibration calibration executed by Rohde & Schwarz Receiver Rohde & Signal Analyzer 100.932 02/2012 02/2013 (9 kHz –30.0 GHz) Schwarz FSV 30 (502) Marconi Instruments signal generator Rohde & Low noise signal generator 119347/003 01/2012 01/2014 (10 kHz –5.4 GHz) Schwarz 2042 (6) Hewlett & Packard Frequency counter Rohde & 5351A Microwave frequency 2432A00054 09/2011 09/2014 (10MHz -26.5GHz) Schwarz counter (130) Hewlett Packard Frequency Counter 3049A01217 08/2011 08/2013 DKD 5351B (432) Low noise Marconi Instruments signal generator 2042 119347/003 01/2012 01/2015 Dudde (10kHz – 5.4GHz) (6) Brabender Temperature chamber --- 03/2010 03/2013 Dudde TTE 32/40 H (87) Sucoflex 104 P Suhner 2,13m RF- cable K17a 01/2012 01/2013 Dudde [APC 3.5] Sucoflex 104 P Suhner 2,13m RF- cable K18a 09/2011 09/2012 Dudde [APC 3.5] RF- cable RG58 2.5m [BNC] K21 01/2012 01/2013 Test fixture Dudde --- 09/2011 09/2012 Dudde Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 24 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 11.5.3 Test procedures Stability with respect to ambient temperature: Supply the EUT with nominal ac voltage, or install a new or fully charged battery in the EUT. If possible, a dummy load should be connected to the EUT, because an antenna near the metallic walls of an environmental test chamber could affect the output frequency of the EUT. If the EUT is equipped with a permanently attached, adjustable-length antenna, the EUT should be placed in the center of the chamber with the antenna adjusted to the shortest length possible. Turn the EUT on, and tune it to one of the number of frequencies required Couple the intentional radiator output to the measuring instrument by connecting an antenna to the measurement instrument with a suitable length of coaxial cable and placing the measurement antenna near the EUT (e.g., 15 cm away) or by connecting a dummy load to the measuring instrument through an attenuator, if necessary. Supply the EUT with nominal ac voltage, or install a new or fully charged battery in the EUT. Turn the EUT on, and couple its output to the measuring instrument by connecting an antenna to the measurement instrument with a suitable length of coaxial cable. Adjust the location of the measurement antenna and the controls on the measuring instrument to obtain a suitable signal level (i.e., a level that will not overload the measuring instrument, but is strong enough to allow measurement of the operating or fundamental frequency of the EUT). Tune the EUT to any one of the number of frequencies specified. Turn the EUT off, and place it inside an environmental chamber if appropriate. Allow the chamber to stabilize at +20 °C before proceeding. Turn on the EUT, and record the operating frequency of the intentional radiator at startup and two, five, and ten minutes after startup. Turn the EUT off and allow it to cool to the ambient temperature, and then repeat this procedure for the number of the frequencies specified. Four measurements are made at each operating frequency. Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 25 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 Stability with respect to input voltage: Supply the EUT with nominal ac voltage, or install a new or fully charged battery in the EUT. If possible, a dummy load should be connected to the EUT, because an antenna near the metallic walls of an environmental test chamber could affect the output frequency of the EUT. If the EUT is equipped with a permanently attached, adjustable-length antenna, the EUT should be placed in the center of the chamber with the antenna adjusted to the shortest length possible. Turn the EUT on, and tune it to one of the number of frequencies required. Couple the intentional radiator output to the measuring instrument by connecting an antenna to the measurement instrument with a suitable length of coaxial cable and placing the measurement antenna near the EUT (e.g., 15 cm away) or by connecting a dummy load to the measuring instrument through an attenuator, if necessary. Adjust the location of the measurement antenna and the controls on the measuring instrument to obtain a suitable signal level (i.e., a level that will not overload the measuring instrument, but is strong enough to allow measurement of the operating or fundamental frequency of the EUT). Turn the EUT off, and place it inside an environmental temperature chamber. For devices that are normally operated continuously, the EUT may be energized while inside the test chamber. For devices that have oscillator heaters, energize only the heater circuit while the EUT is inside the chamber. Set the temperature control on the chamber to the highest specified EUT operating temperature, and allow the temperature inside the chamber to stabilize at the set temperature before starting frequency measurements. While maintaining a constant temperature inside the environmental chamber, turn the EUT on and record the operating frequency at startup and two, five, and ten minutes after the EUT is energized. Four measurements in total are made. Repeat the above procedure until the number of frequencies specified has been measured. After all measurements have been made at the highest specified temperature, turn the EUT off. Repeat the above measurement process for the EUT with the test chamber set at the lowest temperature specified by the regulatory or procuring agency. Measurements shall be made at the number of frequencies specified. Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 26 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 8.5.4 Result Frequency tolerance (Section 15.225(e)) Test conditions Frequency Frequency Error Tnom = +20° C (MHz) (kHz) Vmin = 18.0 V DC 13.560 -0.12 Vmax = 30.0 V DC 13.560 -0.12 Maximum Frequency 0.12 error (MHz) Measurement ± 5*108 uncertainty Frequency tolerance (Section 15.225(e)) Test conditions Frequency Frequency Measured Error Vnom = 24.0 V DC (MHz) (kHz) Tmin -20 °C 13.55981 -0.19 Tmin -10 °C 13.55984 -0.16 Tmin 0 °C 13.55986 -0.14 Tmin +10 °C 13.55986 -0.14 Tmin +20 °C 13.55988 -0.12 Tmin +30 °C 13.55988 -0.12 Tmin +40 °C 13.55990 -0.10 Tmin +50 °C 13.55990 -0.01 Maximum frequency error (kHz) Measurement uncertainty 5 * 10 -8 The equipment meets the requirements Yes No N.t. Further test results are attached Yes No Page no. N.t.* See page no. 27 Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 27 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 9. Additional information to the test report Remarks N.t.1 Not tested, because the antenna is part of the PCB N.t.2 Not tested, because the EUT is directly battery powered N.t.3 Not tested, because not applicable to the EUT N.t.4 Not tested, because not ordered Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 28 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 RFH630 in combination with the internal antenna Emissions according to FCC Part 15C Section 15.225 (b) (c) Modulation depth: 20 % Modulation depth: 100 % Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 29 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 RFH630 in combination with the external antenna RFA332 Emissions according to FCC Part 15C Section 15.225 (b) (c) Modulation depth: 20 % The 9 kHz RBW only used for spurious emission measurement outside the specified band 13.553 MHz up to 13.567 MHz! The emission inside the specified band must be measured according to ANSI C63.4 2009 section 13.7. “Occupied bandwidth measurements”, with lesser RBW! Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007932 Page 30 of 30 EUT: RFH630 Date of issue: 2012-03-12 FCC ID: WRMRFH630 End of test report Date: 2011-03-14 Vers. no. 1.11 dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920


Document Created: 2019-10-24 02:11:20
Document Modified: 2019-10-24 02:11:20
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC