08 ic test report

FCC ID: WQJ-KIOSKIIISRED

Test Report

Download: PDF
FCCID_2814108

Report No.: C150826Z01-RC1 INDUSTRY CANADA RSS-210 TEST REPORT for ViVOpay Kiosk III Model: ViVOpay Kiosk III Brand: ViVOpay Test Report Number: C150826Z01-RC1 Issued for: ID TECH 10721 Walker Street, Cypress, California 90630 Issued by: COMPLIANCE CERTIFICATION SERVICES (SHENZHEN) INC. No.10-1, Mingkeda Logistics Park, No.18, Huanguan South Rd., Guan Lan Town, Baoan District, Shenzhen China TEL: 86-755-28055000 FAX: 86-755-28055221 Issued Date: September 28, 2015 检 测 CNAS L4818 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services (Shenzhen) Inc. This document may be altered or revised by Compliance Certification Services (Shenzhen) Inc. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF, A2LA, NVLAP, NIST or any government agencies. The test result of this report relate only to the tested sample identified in this report. IC : 9847A-KIIISRED Page 1 / 24

Report No.: C150826Z01-RC1 Revision History Effect Rev. Issue Date Revisions Page Revised By 00 September 28, 2015 Initial Issue ALL Nancy Fu IC: 9847A-KIIISRED Page 2 / 24 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150826Z01-RC1 TABLE OF CONTENTS 1 TEST CERTIFICATION..................................................................................................... 4 2 EUT DESCRIPTION .......................................................................................................... 5 3 TEST METHODOLO1GY .................................................................................................. 6 3.1. RSS-210 RESTRICTED BANDS OF OPERATIONS ................................................ 6 3.2. DESCRIPTION OF TEST MODES............................................................................ 6 4 FACILITIES AND ACCREDITATIONS ............................................................................. 7 4.1. FACILITIES ............................................................................................................... 7 4.2. ACCREDITATIONS .................................................................................................. 7 4.3. MEASUREMENT UNCERTAINTY ............................................................................ 7 5 SETUP OF EQUIPMENT UNDER TEST .......................................................................... 8 5.1. DESCRIPTION OF SUPPORT UNITS ...................................................................... 8 5.2. SUPPORT EQUIPMENT .......................................................................................... 8 6 RSS 210 REQUIREMENTS .............................................................................................. 9 6.1. 99% BANDWIDTH .................................................................................................... 9 6.2. RADIATED EMISSIONS ......................................................................................... 11 6.3. POWER LINE CONDUCTED EMISSIONS MEASUREMENT ................................ 20 IC: 9847A-KIIISRED Page 3 / 24 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150826Z01-RC1 1 TEST CERTIFICATION Product ViVOpay Kiosk III Model ViVOpay Kiosk III Brand ViVOpay Tested August 26~September 28, 2015 Applicant ID TECH 10721 Walker Street, Cypress, California 90630 ID TECH Manufacturer 10721 Walker Street, Cypress, California 90630 APPLICABLE STANDARDS STANDARD TEST RESULT IC RSS-210 ISSUE 8 with No non-compliance noted amendment December 2010 We hereby certify that: Compliance Certification Services (Shenzhen) Inc. tested the above equipment in accordance with the requirements set forth in the above standards. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. The test results of this report relate only to the tested sample identified in this report. Approved by: Reviewed by: Sunday Hu Ruby Zhang Supervisor of EMC Dept. Supervisor of Report Dept. Compliance Certification Services (Shenzhen) Inc. Compliance Certification Services (Shenzhen) Inc. IC: 9847A-KIIISRED Page 4 / 24 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150826Z01-RC1 2 EUT DESCRIPTION Product ViVOpay Kiosk III Model ViVOpay Kiosk III Brand ViVOpay Model Discrepancy N/A Identify Number C150826Z01-RC1 Power Supply DC7.5V Supplied by the adapter Received Date August 26, 2015 Frequency Range 13.56 MHz Transmit Power 74.69dBuV/m(measured at 3m) Modulation Technique ASK Number of Channels 1Channels Antenna Specification PCB Antenna with 0dBi gain (MAX) Temperature Range -25°C ~ +70°C Hardware Version 80136304-001&80136302-001 Software Version NEO v1.00 IC: 9847A-KIIISRED Page 5 / 24 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150826Z01-RC1 3 TEST METHODOLO1GY The tests documented in this report were performed in accordance with IC RSS-210, IC RSS-Gen, and ANSI C63.10:2013. This submittal(s) (test report) is intended for IC Certification No: 9847A-KIIISRED filing to comply with Industry CANADA RSS210. 3.1. RSS-210 RESTRICTED BANDS OF OPERATIONS Restricted bands, identified in Table 3 of RSS-Gen. (Note) Table 3: Restricted Frequency Bands MHz MHz MHz GHz 0.090-0.110 12.57675-12.57725 960-1427 9.0-9.2 2.1735-2.1905 13.36-13.41 1435-1626.5 9.3-9.5 3.020-3.026 16.42-16.423 1645.5-1646.5 10.6-12.7 4.125-4.128 16.69475-16.69525 1660-1710 13.25-13.4 4.17725-4.17775 16.80425-16.80475 1718.8-1722.2 14.47-14.5 4.20725-4.20775 25.5-25.67 2200-2300 15.35-16.2 5.677-5.683 37.5-38.25 2310-2390 17.7-21.4 6.215-6.218 73-74.6 2655-2900 22.01-23.12 6.26775-6.26825 74.8-75.2 3260-3267 23.6-24.0 6.31175-6.31225 108-138 3332-3339 31.2-31.8 8.291-8.294 156.52475-156.52525 3345.8-3358 36.43-36.5 8.362-8.366 156.7-156.9 3500-4400 Above 38.6 8.37625-8.38675 240-285 4500-5150 8.41425-8.41475 322-335.4 5350-5460 12.29-12.293 399.9-410 7250-7750 12.51975-12.52025 608-614 8025-8500 Note: Certain frequency bands listed in Table 3 and in bands above 38.6 GHz are designated for licence-exempt applications. These frequency bands and the requirements that apply to the devices are set out in the 200– and 300– series RSSs, such as RSS-210 and RSS-310, which contain the requirements that apply to licence-exempt radio apparatus. 3.2. DESCRIPTION OF TEST MODES The EUT has been tested under operating condition. Test program used to control the EUT for staying in continuous transmitting and receiving mode is programmed. The following test mode(s) were scanned during the preliminary test below 1G and Below 1G: Test Item Test mode Worse mode Conducted Emission Mode 1: TX Radiated Emission Mode 1: TX IC: 9847A-KIIISRED Page 6 / 24 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150826Z01-RC1 4 FACILITIES AND ACCREDITATIONS 4.1. FACILITIES All measurement facilities used to collect the measurement data are located at No.10-1, Mingkeda Logistics Park, No.18, Huanguan South Rd., Guan Lan Town, Baoan District, Shenzhen, China The sites are constructed in conformance with the requirements of ANSI C63.4, ANSI C63.7 and CISPR Publication 22. All receiving equipment conforms to CISPR Publication 16-1, “Radio Interference Measuring Apparatus and Measurement Methods.” 4.2. ACCREDITATIONS Our laboratories are accredited and approved by the following accreditation body according to ISO/IEC 17025. USA A2LA China CNAS The measuring facility of laboratories has been authorized or registered by the following approval agencies. USA FCC Japan VCCI(C-3478, R-3135, T-652, G-624) Canada INDUSTRY CANADA Taiwan BSMI Copies of granted accreditation certificates are available for downloading from our web site, http://www.ccssz.com 4.3. MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: Parameter Uncertainty Radiated Emission, 30 to 200 MHz +/-3.6880dB Test Site : 966(2) Radiated Emission, 200 to 1000 MHz +/-3.6695dB Test Site : 966(2) Radiated Emission, 1 to 8 GHz +/-5.1782dB Radiated Emission, 8 to 18 GHz +/-5.2173dB Conducted Emissions +/-3.6836dB Band Width 178kHz Peak Output Power MU +/-1.906dB Band Edge MU +/-0.182dB Channel Separation MU 416.178Hz Duty Cycle MU 0.054ms Frequency Stability MU 226Hz This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. The measured result is above (below) the specification limit by a margin less than the measurement uncertainty; it is therefore not possible to state compliance based on the 95% level of confidence. However, the result indicates that compliance (non-compliance) is more probable than non-compliance) with the specification limit. IC: 9847A-KIIISRED Page 7 / 24 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150826Z01-RC1 5 SETUP OF EQUIPMENT UNDER TEST 5.1. DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. 5.2. SUPPORT EQUIPMENT Data Power No. Equipment Model No. Serial No. FCC ID Brand Cable Cord Unshielded 1 Notebook B475 WB04861612 DOC LENOVO N/A 1.80m DSA-12PFA-05 Unshielded 2 Adapter N/A N/A DVE N/A FUS 075100 1.50m Note: Grounding was established in accordance with the manufacturer’s requirements and conditions for the intended use. IC: 9847A-KIIISRED Page 8 / 24 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150826Z01-RC1 6 RSS 210 REQUIREMENTS 6.1. 99% BANDWIDTH The test of the item was performed in accordance with the standards RSS-Gen 4.6.1. MEASUREMENT EQUIPMENT USED Name of Serial Last Due Manufacturer Model Equipment Number Calibration Calibration Spectrum Agilent N9010A MY52221469 09/24/2015 09/23/2016 Analyzer Cable HuberSuhner SUCOFLEX104PEA N/A N/A N/A Remark: Each piece of equipment is scheduled for calibration once a year. Test Configuration Spectrum EUT Analyzer TEST PROCEDURE 1. Place the EUT on the table and set it in the transmitting mode. 2. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 3. Set the spectrum analyzer as RBW=1kHz, VBW = 3kHz, Span = 10kHz, Sweep = auto. 4. Record the max. reading. TEST RESULTS Frequency B Channel (MHz) (kHz) CH1 13.56 2.4094 IC: 9847A-KIIISRED Page 9 / 24 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150826Z01-RC1 Test Plot 99% Bandwidth IC: 9847A-KIIISRED Page 10 / 24 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150826Z01-RC1 6.2. RADIATED EMISSIONS 6.2.1. LIMITS OF RADIATED EMISSIONS MEASUREMENT All spurious emissions shall comply with the limits of RSS-Gen Table 2&5&6. Table 2: Radiated Limits of Receiver Spurious Emissions Field Strength Frequency (MHz) (microvolts/m at 3 meters)* 30-88 100 88-216 150 216-960 200 Above 960 500 Note: *Measurements for compliance with limits in the above table may be performed at distances other than 3 metres, in accordance with Section 7.2.7. Table 5: General Field Strength Limits for Transmitters at Frequencies Above 30 MHz Field Strength Frequency (MHz) (microvolts/m at 3 meters)* 30-88 100 88-216 150 216-960 200 Above 960 500 Note: Transmitting devices are not permitted in restricted frequency bands or, unless stated otherwise, in TV bands (54-72 MHz, 76-88 MHz, 174-216 MHz, 470-608 MHz and 614-806 MHz) Table 6: General Field Strength Limits for Transmitters at Frequencies Below 30 MHz (Transmit) Field Strength Magnetic H-Field Measurement Distance Frequency (MHz) (microvolts/m) (microamperes/m) (metres) 0.009-0.490 2,400/F (F in kHz) 2,400/377F (F in kHz) 300 0.490-1.705 24,000/F (F in kHz) 24,000/377F (F in kHz) 30 1.705-30.0 30 N/A 30 Note: The emission limits for the bands 9-90 kHz and 110-490 kHz are based on measurements employing an average detector. In the above emission table, the tighter limit applies at the band edges. Field Strength Field Strength Frequency (MHz) (μV/m at 3-meter) (dBuV/m at 3-meter) 30-88 100 40 88-216 150 43.5 216-960 200 46 Above 960 500 54 IC: 9847A-KIIISRED Page 11 / 24 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Compliance Certfication Services (Shenzhen) Inc. Report No.: €150826Z01—RC1 6.2.2. TEST INSTRUMENTS Radiated Emission Test Site 966 (2) . Serial Last Due Name of Equipment Manufacturer |Model Number Number Calibration Calibration PSA Series Spectrum nalyzer Agilent E4446A uss4soosee omgois ow2r2016 EMI TEST RECEIVER ROHDE&SCHWARZ ESCI 100783 02/28/2015 02/27/2016 Amplifier MITEQ AM—1604—3000 1123808 03/18/2015 03/18/2016 High Noise Amplifier Agilent 84498 3008A01838 02/28/2015 02/27/2016 Board—Band Horn Antenna Schwarzbeck BBHA 9170 9170—497 02/28/2015 02/27/2016 Bilog Antenna SCHAFFNER CBL6143 5082 02/28/2015 02/27/2016 HormAntenna SCHWARZBECK BBHA9120 D286 02/28/2015 02/27/2016 Loop Antenna COM—POWER AL—130 121044 09/25/2015 09/24/2016 Turn Table N/A N/A N/A NCR N.C.R Controller Suno! Sciences SC104V 022310—1 NCR N.C.R Controller CT N/A N/A NCR N.C.R Temp. / Humidity Meter Anymetre JR913 N/A 02/28/2015 02/27/2016 Antenna Tower SUNOL TLT2 N/A NCR N.C.R Test SV FARAD LZ—RF / CCS—SZ—3A2 NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The FCC Site Registration number is 93105/90471. 3. N.C.R = No Calibration Required. 6.2.3. TEST PROCEDURE (please refer to measurement standard) 1. The EUT is placed on a turntable, which is 0.8m above ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emissions. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. Set the spectrum analyzer in the following setting as: Belove 3O0MHz: I9kHz~150kHz: RBW=200Hz / VBW=600Hz / Sweep=AUTO 150kHz~30MHz: RBW=9kHz / VBW=27kHz / Sweep=AUTO Above 30MHz: RBW=100kHz / VBW=300kHz / Sweep=AUTO 7. Repeat above procedures until the measurements for all frequencies are complete. IC: 9847A—KIIISRED Page 12 / 24 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150826Z01-RC1 6.2.4. TEST SETUP Below 30MHz Antenna tower 3m Loop antenna EUT 4m Spectrum / Receiver Turntable 1m 0.8m Pre-amp Reference ground plane Below 1 GHz Antenna tower 3m Bi-log antenna EUT 4m Spectrum analyzer Turntable 1m 0.8m Reference ground plane For the actual test configuration, please refer to the related item – Photographs of the Test Configuration. IC: 9847A-KIIISRED Page 13 / 24 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150826Z01-RC1 6.2.5. ATA SAMPLE Correction Antenna Frequency Reading Result Limit Margin Remark Factor Pole (MHz) (dBuV) (dBuV/m) (dBuV/m) (dB) (dB/m) (V/H) XXX.XXXX 47.40 -21.61 25.79 40.00 -14.21 V QP Frequency (MHz) = Emission frequency in MHz Reading (dBuV) = Uncorrected Analyzer / Receiver reading Correction Factor (dB/m) = Antenna factor + Cable loss – Amplifier gain Result (dBuV/m) = Reading (dBuV) + Corr. Factor (dB/m) Limit (dBuV/m) = Limit stated in standard Margin (dB) = Result (dBuV/m) – Limit (dBuV/m) QP = Quasi-peak Reading IC: 9847A-KIIISRED Page 14 / 24 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150826Z01-RC1 6.2.6. TEST RESULTS Below 30MHz(9kHz~30MHz) Operation Mode: TX Test Date: September 26, 2015 o Temperature: 24 C Tested by: Eve Wang Humidity: 52% RH Frequency Reading Correction Result Limit Margin Remark (MHz) (dBuV) Factor (dBuV/m) (dBuV/m) (dB) (dB/m) 13.5600 60.40 14.29 74.69 124.00 -49.31 Peak IC: 9847A-KIIISRED Page 15 / 24 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150826Z01-RC1 Operation Mode: TX Test Date: September 26, 2015 Temperature: 24oC Tested by: AD Gan Humidity: 52% RH Frequency Reading Correction Result Limit Margin Remark (MHz) (dBμV) Factor (dBμV/m) (dBμV/m) (dB) (dB/m) 0.0145 52.13 14.90 67.03 124.83 -57.80 QP 0.0560 43.32 14.15 57.47 113.17 -55.70 QP 0.0648 45.45 14.14 59.59 111.70 -52.11 QP 7.4931 25.28 14.76 40.04 69.54 -29.50 QP 14.1795 22.09 14.14 36.23 69.54 -33.31 QP 21.5823 13.67 14.32 27.99 69.54 -41.55 QP Remark: 1. The emission behaviour belongs to narrowband spurious emission. 2. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 3. dBuV=dBuA+51.5dB IC: 9847A-KIIISRED Page 16 / 24 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150826Z01-RC1 Below 1 GHz(30MHz~1GHz) Frequency Reading Correction Result Limit Margin Antenna Remark (MHz) (dBμV) Factor (dBμV/m) (dBμV/m) (dB) Pole (dB/m) (V/H) 40.6700 49.93 -16.69 33.24 40.00 -6.76 V QP 232.7300 56.57 -21.75 34.82 46.00 -11.18 V QP 299.6600 55.48 -19.60 35.88 46.00 -10.12 V QP 375.3200 47.66 -16.82 30.84 46.00 -15.16 V QP 515.0000 45.22 -14.19 31.03 46.00 -14.97 V QP 721.6100 40.63 -11.82 28.81 46.00 -17.19 V QP 40.6700 48.71 -16.69 32.02 40.00 -7.98 H QP 232.7300 59.92 -21.75 38.17 46.00 -7.83 H QP 298.6900 59.74 -19.69 40.05 46.00 -5.95 H QP 366.5900 53.99 -17.28 36.71 46.00 -9.29 H QP 487.8400 45.98 -14.36 31.62 46.00 -14.38 H QP 515.0000 47.20 -14.19 33.01 46.00 -12.99 H QP REMARKS: 1. Measuring frequencies from 9kHz to the 1GHz. 2. Radiated emissions measured in frequency range from 30 MHz to 1000MHz were made with an instrument using quasi-peak detector mode. 3. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 4. Margin (dB) = Remark result (dBuV/m) – Quasi-peak limit (dBuV/m) IC: 9847A-KIIISRED Page 17 / 24 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150826Z01-RC1 6.3. FREQUENCY STABILITY LIMIT According to RSS-210 §A2.6, carrier frequency stability shall be maintained to ±0.01% (±100 ppm). TEST CONFIGURATION Temperature and Voltage Measurement (under normal and extreme test conditions) Temperature Chamber Spectrum Analyzer EUT AC/DC Power supply TEST PROCEDURE 1. Place the EUT on the table and set it in the transmitting mode. 2. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 3. Set the environment into appropriate environment. 4. Set the spectrum analyzer as RBW=1kHz, VBW = RBW, Span = 200kHz, Sweep = auto. 5. Mark the peak frequency and measure the frequency tolerance using frequency counter function. 6. Repeat until all the results are investigated. IC: 9847A-KIIISRED Page 18 / 24 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150826Z01-RC1 TEST RESULTS No non-compliance noted. Temperature Variations Measured Delta Temp. Voltage Tolerance Limit Margin Result Frequency Frequency (oC) (VDC) (%) (±%) (%) (Pass/Fail) (MHz) (Hz) -20 13.5606424 10 0.00007 0.01 -0.00993 Pass -10 13.5606318 30 0.00022 0.01 -0.00978 Pass 0 13.5606292 10 0.00007 0.01 -0.00993 Pass 10 13.5606485 170 0.00125 0.01 -0.00875 Pass 7.5 20 13.5606518 10 0.00007 0.01 -0.00993 Pass 30 13.5606592 80 0.00059 0.01 -0.00941 Pass 40 13.5606435 20 0.00015 0.01 -0.00985 Pass 50 13.5606658 100 0.00074 0.01 -0.00926 Pass Voltage Variations Measured Delta Temp. Voltage Tolerance Limit Margin Result Frequency Frequency (oC) (VDC) (%) (±%) (%) (Pass/Fail) (MHz) (Hz) 6.75 13.5606572 150 0.00111 0.01 -0.00889 Pass 20 7.50 13.5607258 10 0.00007 0.01 -0.00993 Pass 8.25 13.5607691 40 0.00029 0.01 -0.00971 Pass IC: 9847A-KIIISRED Page 19 / 24 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150826Z01-RC1 6.4. POWER LINE CONDUCTED EMISSIONS MEASUREMENT 6.4.1. LIMITS OF CONDUCTED EMISSIONS MEASUREMENT According to RSS-Gen §7.2.4, except when the requirements applicable to a given device state otherwise, for any radio apparatus equipped to operate from the public utility AC power supply, either directly or indirectly (such as with a battery charger), the radio frequency voltage of emissions conducted back onto the AC power lines in the frequency range of 0.15 MHz to 30 MHz shall not exceed the limits shown in the table below. The more stringent limit applies at the frequency range boundaries. The conducted emissions shall be measured with a 50 ohm/50 microhenry line impedance stabilization network (LISN). Limits Frequency Range (dBμV) (MHz) Quasi-peak Average 0.15 to 0.50 66 to 56* 56 to 46* 0.50 to 5 56 46 5 to 30 60 50 NOTE: (1) The lower limit shall apply at the transition frequencies. (2) The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50 MHz. TEST INSTRUMENTS Conducted Emission Test Site Name of Last Due Manufacturer Model Number Serial Number Equipment Calibration Calibration EMI TEST RECEIVER ROHDE&SCHWARZ ESCI 100783 04/21/2014 04/21/2015 LISN(EUT) ROHDE&SCHWARZ ENV216 101543-WX 03/01/2015 03/01/2016 LISN EMCO 3825/2 8901-1459 03/01/2015 03/01/2016 Temp. / Humidity Meter VICTOR HTC-1 N/A 03/17/2015 03/17/2016 Cable HuberSuhner SUCOFLEX104PEA N/A N/A N/A Test S/W FARAD EZ-EMC/ CCS-3A1-CE NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. N.C.R = No Calibration Request. IC: 9847A-KIIISRED Page 20 / 24 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150826Z01-RC1 6.4.2. TEST PROCEDURES (please refer to measurement standard)  The EUT and Support equipment, if needed, was placed on a non-conducted table, which is 0.8m above the ground plane and 0.4m away from the conducted wall.  The test equipment EUT installed received AC main power, through a Line Impedance Stabilization Network (LISN), which supplied power source and was grounded to the ground plane. All support equipment power received from a second LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument.  The EUT test program was started. Emissions were measured on each current carrying line of the EUT using an EMI Test Receiver connected to the LISN powering the EUT.  The frequency range from 150 kHz to 30 MHz was searched. The test data of the worst-case condition(s) was recorded. Emission levels under limit 20dB were not recorded. 6.4.3. TEST SETUP Vert. reference plane EMI receiver 40cm EUT 80cm LISN Reference ground plane  For the actual test configuration, please refer to the related item – Photographs of the Test Configuration. 6.4.4. DATA SAMPLE QuasiPeak Average Correction QuasiPeak Average QuasiPeak Average QuasiPeak Average Frequency Line (MHz) Reading Reading Factor Result Result Limit Limit Margin Margin (L1/L2) (dBuV) (dBuV) (dB) (dBuV) (dBuV) (dBuV) (dBuV) (dB) (dB) X.XXXX 32.69 25.65 11.52 44.21 37.17 65.78 55.79 -21.57 -18.62 L1 Frequency = Emission frequency in MHz QuasiPeak Limit (dBuV) = Limit stated in standard Average Limit (dBuV) = Limit stated in standard QuasiPeak Margin (dB) = QuasiPeak Result (dBuV) –QuasiPeak Limit (dBuV) Average Margin (dB) = Average Result (dBuV) –Average Limit (dBuV) L1 = Line One (Live Line) L2 = Line Two (Neutral Line) IC: 9847A-KIIISRED Page 21 / 24 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150826Z01-RC1 6.4.5. TEST RESULTS The initial step in collecting conducted data is a spectrum analyzer peak scan of the measurement range. Significant peaks are then marked as shown on the following data page, and these signals are then quasi-peaked. IC: 9847A-KIIISRED Page 22 / 24 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150826Z01-RC1 Test Data Model No. ViVOpay Kiosk III RBW,VBW 9 kHz Environmental o 22 C, 45% RH Test Mode Normal Conditions Tested by Eve Wang Line L1 Test Date September 10, 2015 QuasiPeak Average Correction QuasiPeak Average QuasiPeak Average QuasiPeak Average Frequency Remark (MHz) Reading Reading Factor Result Result Limit Limit Margin Margin (Pass/Fail) (dBuV) (dBuV) (dB) (dBuV) (dBuV) (dBuV) (dBuV) (dB) (dB) 0.1819 44.58 27.91 9.65 54.23 37.56 64.39 54.40 -10.16 -16.84 Pass 0.3220 40.06 24.99 9.69 49.75 34.68 59.65 49.66 -9.90 -14.98 Pass 0.5780 39.01 25.37 9.72 48.73 35.09 56.00 46.00 -7.27 -10.91 Pass 1.0260 40.33 26.42 9.71 50.04 36.13 56.00 46.00 -5.96 -9.87 Pass 1.6620 38.53 22.78 9.72 48.25 32.50 56.00 46.00 -7.75 -13.50 Pass 9.1020 39.23 26.39 9.84 49.07 36.23 60.00 50.00 -10.93 -13.77 Pass Note: 1. Measuring frequencies from 0.15 MHz to 30MHz. 2. The emissions measured in frequency range from 0.15 MHz to 30MHz were made with an instrument using Peak detector, Quasi-peak detector and average detector. 3. “---” denotes the emission level was or more than 2dB below the Average limit. 4. The IF bandwidth of SPA between 0.15MHz to 30MHz was 10kHz; the IF bandwidth of Test Receiver between 0.15MHz to 30MHz was 9kHz; 5. L1= Line One (Live Line) IC: 9847A-KIIISRED Page 23 / 24 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150826Z01-RC1 Model No. ViVOpay Kiosk III RBW,VBW 9 kHz Environmental o 22 C, 45% RH Test Mode Normal Conditions Tested by Eve Wang Line L2 Test Date September 10, 2015 QuasiPeak Average Correction QuasiPeak Average QuasiPeak Average QuasiPeak Average Frequency Remark (MHz) Reading Reading Factor Result Result Limit Limit Margin Margin (Pass/Fail) (dBuV) (dBuV) (dB) (dBuV) (dBuV) (dBuV) (dBuV) (dB) (dB) 0.1580 43.63 27.80 9.78 53.41 37.58 65.56 55.57 -12.15 -17.99 Pass 0.2860 39.05 25.99 9.76 48.81 35.75 60.64 50.64 -11.83 -14.89 Pass 0.5860 37.49 21.66 9.68 47.17 31.34 56.00 46.00 -8.83 -14.66 Pass 1.1539 35.54 16.91 9.79 45.33 26.70 56.00 46.00 -10.67 -19.30 Pass 2.0780 35.76 17.34 9.73 45.49 27.07 56.00 46.00 -10.51 -18.93 Pass 6.3100 39.46 23.50 9.78 49.24 33.28 60.00 50.00 -10.76 -16.72 Pass Note: 1. Measuring frequencies from 0.15 MHz to 30MHz. 2. The emissions measured in frequency range from 0.15 MHz to 30MHz were made with an instrument using Peak detector, Quasi-peak detector and average detector. 3. “---” denotes the emission level was or more than 2dB below the Average limit. 4. The IF bandwidth of SPA between 0.15MHz to 30MHz was 10kHz; the IF bandwidth of Test Receiver between 0.15MHz to 30MHz was 9kHz; 5. L2= Line Two (Neutral Line) IC: 9847A-KIIISRED Page 24 / 24 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.


Document Created: 2015-11-06 09:28:25
Document Modified: 2015-11-06 09:28:25
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC