Test Report

FCC ID: WQJ-IDCA36-0119

Test Report

Download: PDF
FCCID_1067219

FCC ID: WQJ- IDCA36-0119 FCC TEST REPORT REPORT NO.: 090110FIA01 MODEL NO.: IDCA-3620 RECEIVED: Jan. 14, 2009 TESTED: Jan. 14 ~ Jan. 19, 2009 ISSUED: Feb. 04, 2009 APPLICANT: ID TECH ADDRESS: 10721 Walker Street, Cypress, CA 90630, USA ISSUED BY: ADT (Shanghai) Corporation 2F, Building C, No.1618, Yishan rd., 201103, LAB LOCATION: Shanghai, China This test report consists of 34 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by TAF, A2LA or any government agencies. The test results in the report only apply to the tested sample. Report No.: 080913FIA01 1 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 Table of Contents 1 CERTIFICATION............................................................................................. 4 2 SUMMARY OF TEST RESULTS .................................................................... 5 2.1 MEASUREMENT UNCERTAINTY...................................................................5 3 GENERAL INFORMATION ............................................................................. 6 3.1 GENERAL DESCRIPTION OF EUT ................................................................6 3.2 DESCRIPTION OF TEST MODES ..................................................................7 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST..............................................7 3.2.2 TEST MODE APPLICABILITY .........................................................................8 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS..................................9 3.4 FOR EMISSION TEST.....................................................................................9 4 TEST TYPES AND RESULTS ...................................................................... 10 4.1 CONDUCTED EMISSION MEASUREMENT.................................................10 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ..............................10 4.1.2 TEST INSTRUMENTS...................................................................................10 4.1.3 TEST PROCEDURE...................................................................................... 11 4.1.4 DEVIATION FROM TEST STANDARD.......................................................... 11 4.1.5 TEST SETUP.................................................................................................12 4.1.6 EUT OPERATING CONDITIONS ..................................................................12 4.1.7 TEST RESULTS ............................................................................................13 4.2 RADIATED EMISSION MEASUREMENT......................................................15 4.2.1 LIMIT OF RADIATED EMISSION MEASUREMEN........................................15 4.2.2 TEST INSTRUMENTS...................................................................................16 4.2.3 TEST PROCEDURE......................................................................................17 4.2.4 DEVIATION FROM TEST STANDARD..........................................................17 4.2.5 TEST SETUP.................................................................................................18 4.2.6 EUT OPERATING CONDITIONS ..................................................................18 4.2.7 TEST RESULTS ............................................................................................19 4.3 FREQUENCY STABILITY..............................................................................23 4.3.1 LIMITS OF FREQUENCY STABILITY MEASUREMENT ..............................23 4.3.2 TEST INSTRUMENTS...................................................................................23 4.3.3 TEST PROCEDURE......................................................................................24 4.3.4 DEVIATION FROM TEST STANDARD..........................................................24 4.3.5 TEST SETUP.................................................................................................25 4.3.6 EUT OPERATING CONDITIONS ..................................................................25 4.3.7 TEST RESULTS ............................................................................................26 4.4 BANDEDGE...................................................................................................27 4.4.1 LIMIT OF THE FIELD STRENGTH IN THE SPECIAL BAND FOR THE PRODUCTS OPERATION WITHIN THE BAND 13.110-14.010MHZ............27 4.4.2 TEST INSTRUMENTS...................................................................................27 4.4.3 TEST PROCEDURE......................................................................................28 4.4.4 DEVIATION FROM TEST STANDARD..........................................................28 4.4.5 TSET SETUP.................................................................................................29 4.4.6 EUT OPERATING CONDITIONS ..................................................................29 4.4.7 TEST RESULTS ............................................................................................29 5 PHOTOGRAPHS OF THE TEST CONFIGURATION ................................... 32 Report No.: 080913FIA01 2 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 6 APPENDIX - INFORMATION ON THE TESTING LABORATORIES ............ 34 Report No.: 080913FIA01 3 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 1 CERTIFICATION PRODUCT: OmniXpress/OmniFare MODEL: IDCA-3620 BRAND: ID TECH APPLICANT: ID TECH TEST SAMPLE: ENGINEERING SAMPLE TESTED: Jan. 14~ Jan. 19, 2009 STANDARDS: FCC Part 15, Subpart C (Section 15.225) ANSI C63.4-2003 The above equipment has been tested by ADT (Shanghai) Corporation, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: Feb. 04, 2009 ( Ray Xue / Engineer) TECHNICAL ACCEPTANCE : , DATE: Feb. 04, 2009 Responsible for EMS (Joy Zhu / Manager) APPROVED BY : , DATE: Feb. 04, 2009 ( Wallace Pan / Director ) Report No.: 080913FIA01 4 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 2 SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications: APPLIED STANDARD: FCC PART 15, SUBPART C (SECTION 15.225) STANDARD TEST TYPE AND LIMIT RESULT REMARK SECTION Meet the requirement of AC Power Conducted limit. 15.207 PASS Emission Minimum passing margin is -2.46dB at 27.12MHz Meet the requirement of 15.225(a) Field Strength PASS limit. Meet the requirement of limit. 15.225(d) Radiated Emission PASS Minimum passing margin is -1.99dB at 230.55MHz Meet the requirement of 15.225(e) Frequency Stability PASS limit. 2.1 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Measurement Value Conducted emissions 2.55 dB Radiated emissions 3.99 dB Report No.: 080913FIA01 5 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 3 GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT EUT OmniXpress/OmniFare MODEL NO. IDCA-3620 FCC ID WQJ- IDCA36-0119 POWER SUPPLY 120Vac, 60Hz MODULATION TYPE ASK FREQUENCY RANGE 13.56MHz NUMBER OF CHANNEL 1 ANTENNA TYPE Soldered on PCB 1m shielded RS232 cable with one core, DATA CABLE undetachable I/O PORTS Refer to user’s manual ASSOCIATED DEVICES Adapter NOTE: 1. The EUT is powered by the following adapter. ADAPTER BRAND ID TECH MODEL MW41-0500500R INPUT POWER 120Vac, 60Hz, 5W OUTPUT POWER 5Vdc, 500mA POWER LINE 1.8m non-shielded cable with one core 2. The above EUT information was declared by the manufacturer and for more detailed features description, please refer to the manufacturer's specifications or User's Manual. Report No.: 080913FIA01 6 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 3.2 DESCRIPTION OF TEST MODES The EUT only has one channel. TRANSMITTER CHANNEL FREQUENCY (MHz) 1 13.56 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST Report No.: 080913FIA01 7 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 3.2.2 TEST MODE APPLICABILITY EUT APPLICABLE TO CONFIGURE DESCRIPTION MODE PLC RE FS 1 √ √ √ Continuous card reading station Where PLC: Power Line Conducted Emission RE: Radiated Emission FS: Frequency Stability POWER LINE CONDUCTED EMISSION TEST:  Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture).  Following channel(s) was (were) selected for the final test as listed below. AVAILABLE TESTED MODULATION CHANNEL CHANNEL TYPE 1 1 ASK RADIATED EMISSION TEST:  Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates, XYZ Axis and antenna ports (if EUT with antenna diversity architecture).  Following channel(s) was (were) selected for the final test as listed below. AVAILABLE TESTED MODULATION AXIS CHANNEL CHANNEL TYPE 1 1 ASK Y FREQUENCY STABILITY:  Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture).  Following channel(s) was (were) selected for the final test as listed below. AVAILABLE TESTED MODULATION CHANNEL CHANNEL TYPE 1 1 ASK Report No.: 080913FIA01 8 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS The EUT is a RF Product. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart C (15.225) ANSI C63.4-2003 All test items have been performed and recorded as per the above standards. NOTE: The EUT is also considered as a kind of computer peripheral, because the connection to computer is necessary for typical use. It has been verified to comply with the requirements of FCC Part 15, Subpart B, Class B (DoC). The test report has been issued separately. 3.4 FOR EMISSION TEST The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. NO. PRODUCT BRAND MODEL NO. SERIAL NO. FCC ID 1 PC DELL DCSM E1P2012 FCC DoC Approved 2 Monitor Samsung 743N E1M2004 FCC DoC Approved 3 Keyboard Logitech Y-UR83 E1K2033 FCC DoC Approved 4 Mouse Logitech M-BZ96C N/A FCC DoC Approved NO. SIGNAL CABLE DESCRIPTION OF THE ABOVE SUPPORT UNITS A 1.2m shielded VGA cable with one core B 1.5m shielded USB cable without core C 1.5m shielded USB cable without core D 1m shielded RS232 cable with one core Report No.: 080913FIA01 9 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 4 TEST TYPES AND RESULTS 4.1 CONDUCTED EMISSION MEASUREMENT 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT FREQUENCY OF EMISSION (MHz) CONDUCTED LIMIT (dBµV) Quasi-peak Average 0.15 ~ 0.5 66 to 56 56 to 46 0.5 ~ 5 56 46 5 ~ 30 60 50 NOTE: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50MHz. 3. All emanations from a class A/B digital device or system, including any network of conductors and apparatus connected thereto, shall not exceed the level of field strengths specified above. 4.1.2 TEST INSTRUMENTS DESCRIPTION & CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER UNTIL Test Receiver ESCS30 E1R1002 Oct. 31, 2009 ROHDE & SCHWARZ LISN NSLK8127 E1L1001 Jul. 31, 2009 ROHDE & SCHWARZ LISN NSLK8126 E1L1002 Oct. 31, 2009 ROHDE & SCHWARZ Software ADT_Cond_V7.3.0 N/A N/A ADT Report No.: 080913FIA01 10 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 4.1.3 TEST PROCEDURE a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150kHz to 30MHz was searched. Emission levels under (Limit - 20dB) was not recorded. 4.1.4 DEVIATION FROM TEST STANDARD No deviation Report No.: 080913FIA01 11 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 4.1.5 TEST SETUP V e r tic a l G r o u n d R e fe r e n c e P la n e Te s t R e c e iv e r EUT 40cm 80cm L IS N H o r iz o n ta l G r o u n d R e fe r e n c e P la n e N o t e : 1 . S u p p o r t u n i ts w e r e c o n n e c t e d t o s e c o n d L I S N . 2 . B o t h o f L IS N s ( A M N ) a r e 8 0 c m f r o m E U T a n d a t l e a s t 8 0 c m f r o m o t h e r u n i ts a n d o t h e r m e ta l p l a n e s For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.1.6 EUT OPERATING CONDITIONS a. Set up PC as the usual using configuration. b. Link EUT to PC by RS232 cable, then plug in power. c. Run manufactory’s test software to make sure EUT continues emission station. d. Take away the mouse, keyboard and monitor while test. Report No.: 080913FIA01 12 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 4.1.7 TEST RESULTS INPUT POWER 120Vac, 60Hz PHASE Line 1 MODULATION ENVIRONMENTAL 23deg. C, 65%RH, ASK TYPE CONDITIONS 1006hPa TESTED BY Ray Xue Emission Freq. Corr. Reading Value Limit Margin Level No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.15 1.87 41.87 11.65 43.74 13.52 66.00 56.00 -22.26 -42.48 2 0.45 0.61 34.38 6.04 34.99 6.65 56.95 46.95 -21.96 -40.30 3 0.88 0.55 29.45 -1.06 30.00 -0.51 56.00 46.00 -26.00 -46.51 4 6.71 0.88 22.32 16.81 23.20 17.69 60.00 50.00 -36.80 -32.31 5 9.50 0.94 21.35 0.14 22.29 1.08 60.00 50.00 -37.71 -48.92 6 27.13 1.54 42.01 42.01 43.55 43.55 60.00 50.00 -16.45 -6.45 REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. Margin value = Emission level - Limit value 5. Correction factor = Insertion loss + Cable loss 6. Emission Level = Correction Factor + Reading Value. Report No.: 080913FIA01 13 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 INPUT POWER 120Vac, 60Hz PHASE Line 2 MODULATION ENVIRONMENTAL 23deg. C, 65%RH, ASK TYPE CONDITIONS 1006hPa TESTED BY Ray Xue Emission Freq. Corr. Reading Value Limit Margin Level No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.15 1.83 41.89 11.80 43.72 13.63 65.93 55.93 -22.21 -42.30 2 0.47 0.60 35.34 4.81 35.94 5.41 56.58 46.58 -20.64 -41.17 3 0.87 0.64 29.53 -0.23 30.17 0.41 56.00 46.00 -25.83 -45.59 4 6.66 0.80 24.47 18.78 25.27 19.58 60.00 50.00 -34.73 -30.42 5 9.33 0.89 27.46 13.73 28.35 14.62 60.00 50.00 -31.65 -35.38 6 27.12 1.48 46.00 46.06 47.48 47.54 60.00 50.00 -12.52 -2.46 REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. Margin value = Emission level - Limit value 5. Correction factor = Insertion loss + Cable loss 6. Emission Level = Correction Factor + Reading Value. Report No.: 080913FIA01 14 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 4.2 RADIATED EMISSION MEASUREMENT 4.2.1 LIMIT OF RADIATED EMISSION MEASUREMEN According to 15.225 the field strength of Emissions from intentional radiators operated under these frequencies bands shall not exceed the following: Fundamental Frequency Field Strength of Fundamental (dBuV/m) (MHz) Quasi-Peak 13.110 – 14.010 124 Field strength limits are at the distance of 3 meters, Emissions radiated outside of the specified bands, shall be according to the general radiated limits in 15.209 as following: FREQUENCIES FIELD STRENGTH MEASUREMENT DISTANCE (MHz) (microvolts/meter) (meters) 0.009 ~ 0.490 2400/F(kHz) 300 0.490 ~ 1.705 24000/F(kHz) 30 1.705 ~ 30.0 30 30 30 ~ 88 100 3 88 ~ 216 150 3 216 ~ 960 200 3 Above 960 500 3 NOTE: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. As shown in 15.35(b), for frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. Report No.: 080913FIA01 15 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 4.2.2 TEST INSTRUMENTS DESCRIPTION & CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER UNTIL Spectrum E4403B E1S1001 Jul. 31, 2009 Agilent Receiver ESCS30 E1R1001 Oct. 31, 2009 R&S Trilog Broadband Antenna VULB 9168 E1A1001 Aug. 31, 2009 Schwarzbeck Active Loop Antenna AL-130 E1A1010 Aug. 31, 2009 Com-power Horn Antenna BBHA 9120D E1A1002 Sep. 30, 2009 Schwarzbeck Preamplifier 8447D E1A2001 Oct. 01, 2010 Agilent Preamplifier 8449B E1A2002 Aug. 01, 2009 Agilent Software ADT_Radiated_V7.5 N/A N/A ADT Report No.: 080913FIA01 16 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 4.2.3 TEST PROCEDURE a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter semi-anechoic camber. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna is a broadband antenna, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. For test below 30MHz, we use loop antenna and its height fixed by 1m above the ground. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. f. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. NOTE: The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120 kHz for Peak detection (PK) and Quasi-peak detection (QP) at frequency below 1GHz.And 9kHz and 30kHz for Peak detection (PK) and Quasi-peak detection (QP) at frequency below 30MHz 4.2.4 DEVIATION FROM TEST STANDARD No deviation Report No.: 080913FIA01 17 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 4.2.5 TEST SETUP For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.2.6 EUT OPERATING CONDITIONS Same as item 4.1.6. Report No.: 080913FIA01 18 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 4.2.7 TEST RESULTS FREQUENCY INPUT POWER 120Vac, 60 Hz Below 1000MHz RANGE ENVIRONMENTAL 26deg. C, 68%RH, DETECTOR Peak CONDITIONS 1006hPa FUNCTION TESTED BY Ray Xue ANTENNA POLARITY & TEST DISTANCE: LOOP ANTENNA 0 DEGREE OPEN AT 3 M Reading Emission Antenna Table Freq. Factor Limit Margin No. Value Level Height Angle [MHz] (dB) [dB (uV)] [dB (uV)] [dB (uV)] (dB) (m) (Degree) 1 13.56 11.59 67.55 79.14 124 -44.86 99 0 ANTENNA POLARITY & TEST DISTANCE: LOOP ANTENNA 90 DEGREE OPEN AT 3 M Reading Emission Antenna Table Freq. Factor Limit Margin No. Value Level Height Angle [MHz] (dB) [dB (uV)] [dB (uV)] [dB (uV)] (dB) (m) (Degree) 1 13.56 11.59 67.86 79.45 124 -44.55 99 0 REMARKS: 1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. 5. ”∗”= Fundamental frequency. 6. Loop Antenna was used for all frequency below 30MHz. Report No.: 080913FIA01 19 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 INPUT POWER 120Vac, 60Hz FREQUENCY RANGE 9kHz – 30MHz ENVIRONMENTAL 26deg. C, 68%RH, DETECTOR Quasi-Peak CONDITIONS 1006hPa FUNCTION TESTED BY Ray Xue ANTENNA POLARITY & TEST DISTANCE: LOOP ANTENNA 0 DEGREE OPEN AT 3 M Reading Emission Antenna Table Freq. Factor Limit Margin No. Value Level Height Angle [MHz] (dB) [dB (uV)] [dB (uV)] [dB (uV)] (dB) (m) (Degree) 1 15.42 11.30 9.36 20.66 69.54 -48.89 99 327 2 27.12 9.88 29.50 39.37 69.54 -30.17 99 352 ANTENNA POLARITY & TEST DISTANCE: LOOP ANTENNA 90 DEGREE CLOSE AT 3 M Reading Emission Antenna Table Freq. Factor Limit Margin No. Value Level Height Angle [MHz] (dB) [dB (uV)] [dB (uV)] [dB (uV)] (dB) (m) (Degree) 1 22.86 10.73 14.56 25.29 69.54 -44.25 99 346 2 27.12 9.88 34.57 44.44 69.54 -25.10 99 19 REMARKS: 1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. 5. Loop Antenna was used for all frequency below 30MHz. Report No.: 080913FIA01 20 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 FREQUENCY TEST MODE Mode 1 30-1000 MHz RANGE DETECTOR INPUT POWER 120Vac, 60 Hz FUNCTION & Quasi-Peak, 120kHz BANDWIDTH ENVIRONMENTAL 32 deg. C, 57% RH, TESTED BY: Brain Chen CONDITIONS 998hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Freq. Factor Reading Emission Limit Margin Tower Table No. (MHz) (dB) (dbuv/m) (dbuv/m) (dbuv/m) (dB) cm deg 1 203.43 13.01 28.33 41.34 43.50 -2.16 99 107 2 230.55 14.54 29.47 44.01 46.00 -1.99 100 335 3 244.10 14.77 27.95 42.73 46.00 -3.27 100 352 4 284.80 16.01 26.65 42.67 46.00 -3.33 100 3 5 311.90 16.94 25.48 42.42 46.00 -3.58 100 6 6 553.80 22.15 0.84 22.98 46.00 -23.02 100 192 REMARKS: 1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. Report No.: 080913FIA01 21 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 FREQUENCY TEST MODE Mode 1 30-1000 MHz RANGE DETECTOR INPUT POWER 120Vac, 60 Hz FUNCTION & Quasi-Peak, 120kHz BANDWIDTH ENVIRONMENTAL 32 deg. C, 57% RH, TESTED BY: Brain Chen CONDITIONS 998hPa ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M Freq. Factor Reading Emission Limit Margin Tower Table No. (MHz) (dB) (dbuv/m) (dbuv/m) (dbuv/m) (dB) cm deg 1 67.80 13.38 19.79 33.16 40.00 -6.84 99 287 2 176.30 15.18 25.41 40.60 43.50 -2.90 99 207 3 203.43 13.01 20.41 33.42 43.50 -10.08 99 248 4 230.55 14.54 23.26 37.80 46.00 -8.20 0 0 5 311.90 16.94 22.84 39.78 46.00 -6.22 99 233 6 553.80 22.15 -4.62 17.52 46.00 -28.48 99 327 REMARKS: 1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. Report No.: 080913FIA01 22 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 4.3 FREQUENCY STABILITY 4.3.1 LIMITS OF FREQUENCY STABILITY MEASUREMENT The frequency tolerance of the carrier signal shall be maintained within +/- 0.01% of the operating frequency over a temperature variation of -20 degrees to 50 degrees C at normal supply voltage, and for a variation in the primary supply voltage from 85% to 115% of the rated supply voltage at a temperature of 20 degrees C. For battery operated equipment, the equipment tests shall be performed using a new battery. 4.3.2 TEST INSTRUMENTS DESCRIPTION & CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER UNTIL Spectrum FSP E1S1002 Jul. 31, 2009 R&S Digital Meter 15B E2M7003 Jul. 02, 2009 FLUKE Temperature & humidity Chamber KTHC－715TBS E3004 Jul. 21, 2009 KING SON Report No.: 080913FIA01 23 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 4.3.3 TEST PROCEDURE a. The EUT was placed inside the environmental test chamber and powered by nominal DC voltage. b. Turn the EUT on and couple its output to a spectrum analyzer. c. Turn the EUT off and set the chamber to the highest temperature specified. d. Allow sufficient time (approximately 30 min) for the temperature of the chamber to stabilize, turn the EUT on and measure the operating frequency after 2, 5, and 10 minutes. e. Repeat step 2 and 3 with the temperature chamber set to the following temperatures in the under table until to the lowest. f. The test chamber was allowed to stabilize at +20 degree C for a minimum of 30 minutes. The supply voltage was then adjusted on the EUT from 85% to 115% and the frequency record. 4.3.4 DEVIATION FROM TEST STANDARD No deviation Report No.: 080913FIA01 24 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 4.3.5 TEST SETUP 4.3.6 EUT OPERATING CONDITIONS Same as item 4.1.6. Report No.: 080913FIA01 25 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 4.3.7 TEST RESULTS OPERATING FREQUENCY: 13.5616MHz LIMIT: ± 0.01% 0 MINUTE 2 MINUTE 5 MINUTE 10 MINUTE POWER TEMP. SUPPLY (℃) (Vdc) (MHz) (%) (MHz) (%) (MHz) (%) (MHz) (%) 50 120 13.5616 0 13.5616 0 13.5618 0.0015 13.5618 0.0015 40 120 13.5616 0 13.5616 0 13.5618 0.0015 13.5618 0.0015 30 120 13.5618 0.0015 13.5618 0.0015 13.5616 0 13.5618 0.0015 20 120 13.5616 0 13.5616 0 13.5616 0 13.5616 0 10 120 13.5616 0 13.5616 0 13.5616 0 13.5618 0.0015 0 120 13.5618 0.0015 13.5618 0.0015 13.5618 0.0015 13.5618 0.0015 -10 120 13.5618 0.0015 13.5618 0.0015 13.5622 0.0044 13.5618 0.0015 -20 120 13.5622 0.0044 13.5622 0.0044 13.5622 0.0044 13.5622 0.0044 0 MINUTE POWER TEMP. SUPPLY (℃) (Vdc) (MHz) (%) 20 138 13.5616 0 20 120 13.5616 0 20 102 13.5616 0 Report No.: 080913FIA01 26 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 4.4 BANDEDGE 4.4.1 LIMIT OF THE FIELD STRENGTH IN THE SPECIAL BAND FOR THE PRODUCTS OPERATION WITHIN THE BAND 13.110-14.010MHZ According to 15.225 (a) The field strength of any emissions within the band 13.553-13.567 MHz shall not exceed 15,848 microvolts/meter at 30 meters. (b) Within the bands 13.410-13.553 MHz and 13.567-13.710 MHz, the field strength of any emissions shall not exceed 334 microvolts/meter at 30 meters. (c) Within the bands 13.110-13.410 MHz and 13.710-14.010 MHz the field strength of any emissions shall not exceed 106 microvolts/meter at 30 meters. The limit of the field strength in the special band at the test distance of 3 meters shall not exceed the following: FREQUENCIES FIELD STRENGTH (dBuV/m) (MHz) 13.11-13.41,13.71-14.01 80.5 13.41-13.553,13.567-13.71 90.5 13.553-13.567 124 4.4.2 TEST INSTRUMENTS DESCRIPTION & CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER UNTIL Spectrum FSP E1S1002 Jul. 31, 2009 R&S Active Loop Antenna AL-130 E1A1010 Aug. 31, 2009 Com-power Software ADT_Radiated_V7.5 N/A N/A ADT Report No.: 080913FIA01 27 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 4.4.3 TEST PROCEDURE a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter semi-anechoic camber. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna. c. The antenna is a loop antenna, with the antenna height 1 meter from the ground. Both 0 and 90 degrees of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case, and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. f. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. NOTE: The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 9 kHz and 30kHz for Peak detection (PK) and Quasi-peak detection (QP) at frequency below 30MHz. 4.4.4 DEVIATION FROM TEST STANDARD No deviation Report No.: 080913FIA01 28 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 4.4.5 TSET SETUP For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.4.6 EUT OPERATING CONDITIONS Same as item 4.1.6. 4.4.7 TEST RESULTS The following two plots show the emission in the special band. Loop antenna: 0 degree Report No.: 080913FIA01 29 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 * RBW 10 kHz Marker 1 [T1 ] * VBW 30 kHz 77.78 dBµV Ref 137 dBµV * Att 70 dB SWT 10 ms 13.561800000 MHz 130 A 1 PK 120 VIEW 110 TDF 100 PRN 90 Limit_1 80 1 70 60 50 40 Start 13.11 MHz 90 kHz/ Stop 14.01 MHz Date: 16.JAN.2009 13:15:00 Loop antenna: 90 degree Report No.: 080913FIA01 30 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 * RBW 10 kHz Marker 1 [T1 ] * VBW 30 kHz 80.14 dBµV Ref 137 dBµV * Att 70 dB SWT 10 ms 13.563058000 MHz 130 A 1 PK 120 VIEW 110 TDF 100 PRN 90 Limit_1 1 80 70 60 50 40 Start 13.11 MHz 90 kHz/ Stop 14.01 MHz Date: 16.JAN.2009 13:09:55 Report No.: 080913FIA01 31 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 5 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.: 080913FIA01 32 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 RADIATED EMISSION TEST Report No.: 080913FIA01 33 Report Format Version 3.0.0

FCC ID: WQJ- IDCA36-0119 6 APPENDIX - INFORMATION ON THE TESTING LABORATORIES We, ADT (Shanghai) Corporation, were founded in 2004 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved by the following approval agencies according to ISO/IEC 17025. USA FCC, A2LA Japan VCCI Canada INDUSTRY CANADA P.O.C. CNAS Copies of accreditation certificates of our laboratories obtained from approval agencies can be downloaded from our web site: www.cnadt.com. If you have any comments, please feel free to contact us at the following: Shanghai EMC / RF / Auto Lab: Tel: +86-21-64659091 Fax:+86-21-64659092 Email: service@adt-sh.com Web Site: www.cnadt.com The address and road map of all our labs can be found in our web site also. --- END --- Report No.: 080913FIA01 34 Report Format Version 3.0.0


Document Created: 2009-02-06 20:04:48
Document Modified: 2009-02-06 20:04:48
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC