Users Manual

FCC ID: WDQ-DW10345

Users Manual

Download: PDF
FCCID_1160961

Thin Door/Window Contact 2GIG-DW10-345 Battery Installation & Replacement Under normal conditions the battery can last up to 5 years. If a sensor battery is low, a low battery notification will be indicated on Operating Instructions the 2GIG Alarm Control Panel’s screen. When the 2GIG alarm system indicates that there is a sensor with a low battery, replace the battery immediately. Use only the recommended replacement batteries (see Specifications). To install or replace the battery, do the following: The 2GIG-DW10-345 is a Thin Door/Window Contact that can be installed on doors, 1. To remove the sensor cover, use your finger to press the tab on the end of the case. This will disengage the clip holding the windows, and many other objects that open and close. The sensor transmits signals cover to the base. to the control panel when a magnet mounted near the sensor is moved away from 2. Place a small flathead screwdriver in the slot between the metal clip (see Figure 3) and the battery and twist the screwdriver or closer to the sensor. The sensor has an external input that accepts N/C dry slightly while holding back one of the black plastic edges holding the battery. contact devices. The sensor is also equipped with a cover tamper for additional 3. Insert the replacement battery with the + sign facing out. (see Figure 3) 4. Verify programming and RF communication with the panel. (see Testing). security. Figure 1 WARNING! The polarity of the battery must be observed, as shown (see Figure 3). Improper handling of lithium batteries may result in heat generation, explosion or fire, which may lead to personal injuries. Replace only with the Installation & Mounting Guidelines same or equivalent type of battery as recommended by the manufacturer. (see Specifications) Use the following guidelines for internal switch usage: Batteries must not be recharged, disassembled or disposed of in fire. Disposal of used batteries must be made in accor- dance with the waste recovery and recycling regulations in your area. 1. Mount the sensor on the door frame and the magnet on the door. If the sensor is used on Keep away from small children. If batteries are swallowed, promptly see a doctor. double doors, mount the sensor on the least-used door and the magnet on the most-used door. California Only: This Perchlorate warning applies only to Manganese Dioxide Lithium cells sold or distributed ONLY in California, 2. If possible, locate sensors within 100 ft. (30 m) of the panel. While a transmitter may have a USA. Perchlorate Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate. range of 500 ft. (150 m) or more out in the open, the environment at the installation site can have a significant effect on transmitter range. Sometimes a change in sensor orientation can Specifications help overcome adverse wireless conditions. Wireless Signal Range 500 ft., open air, with 2GIG Wireless Alarm Control Panel 3. Make sure the alignment arrow on the magnet points to the alignment mark on the sensor Code Outputs Alarm; Alarm Restore; External Alarm; External Restore; Tamper; Tamper Restore; (see Figure 1). Supervisory; Low Battery 4. Place sensors at least 4.7 in. (12 cm) above the floor to avoid damaging them. Transmitter Frequency 345.000 MHz (crystal controlled) 5. Avoid mounting sensors in areas where they will be exposed to moisture or where the sensor Transmitter Frequency Tolerance ± 10 kHz operating temperature range of 32 to 120°F (0 to 49°C) will be exceeded. Transmitter Bandwidth 24 kHz Modulation Type Amplitude Shift Keying—On/Off Keying (ASK-OOK) 6. Use spacers (not included) to keep sensors and magnets away from metal or metallic surfaces Unique ID Codes Over one (1) million different code combinations such as foil wallpaper. Supervisory Interval 70 minutes 7. Avoid mounting sensors in areas with a large quantity of metal or electrical wiring, such as a Figure 2 Peak Field Strength Typical 36,000 uV/m at 3m furnace or utility room. External Input Sampling Current 20 uA External Input Accepts N/C dry contact devices To mount the sensor, do the following: Reed Switch Magnetic Sensitivity 10 to 20 amp turns 1. Place the base of the sensor in the desired location and secure with included screws (see Figure 2). Reed Sensitivity 0.625 in. (1.59 cm) minimum gap, 0.85 in. (2.16 cm) typical 2. When mounting the magnet, line up the arrow on the magnet with the middle line on one side of the Magnet Type Rare earth sensor (see Figure 1). Mount the magnet no more than 0.4 in. (1 cm) away from the sensor. Be sure to Magnet Dimensions (LxWxH) 1.3 x 0.435 x 0.312 in. (3.3 x 1.1 x 0.79 cm) Sensor Dimensions (LxWxH) 2.59 x 1.03 x 0.49 in. (6.58 x 2.62 x 1.24 cm) secure the magnet with provided adhesive. Weight (including battery & magnet) 1.1 oz. (31.2 g) To use the external input: Housing Material ABS plastic Color White 1. Repeat above instructions for mounting. Operating Temperature 32° to 120°F (0° to 49°C) 2. Drill hole through access hold, if needed (see Figure 2). Relative Humidity 5-95% Non-Condensing 3. Plug two-pin connector into J1 (see Figure 3). Battery (included, not installed) Two (2) Panasonic CR2032, 3 VDC, 225 mAh or equivalent Lithium coin batteries 4. Connect wire to N/C dry contact device. Battery Life 5 years Regulatory Listing(s) ETL, FCC Part 15, Industry Canada Warranty* Two (2) years Programming Included Accessories Two (2) Phillip’s flat-head screws, one (1) two-pin connector with a 12” flying 2-wire The following steps describe general guidelines for programming (learning) the sensor lead, adhesive strip into panel memory. Refer to the specific panel’s installation instructions for complete programming details. FCC COMPLIANCE STATEMENT* 1. To remove the sensor cover, use your finger to press the tab on the end of the This device complies with FCC Rules and Regulations as Part 15 devices, as well as Industry Canada Rules and Regulations. Operation is subject to the following two conditions: case. This will disengage the clip holding the cover to the base. 2. Set the panel to sensor learning mode. 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. 3. Press and release the tamper switch (SW1) on the sensor until the panel responds (see Figure 3). FCC ID: WDQ-DW10345 Industry Canada ID: 7794A-DW10345 4. Replace the base of the sensor. Note: Changes or modifications to the device may void FCC compliance. 5. Exit program mode. Figure 3 *For more warranty and compliance information, visit our website (www.2gig.com). Testing Before mounting the sensor, verify that the sensor mounting location provides good RF communication to the panel. To verify, do the following: 1. Put the control panel into sensor test mode. 2. Hold the magnet next to the alignment mark on the side of the sensor and then pull the magnet away from Technical Support: the sensor. 1-866-670-1591 3. Listen for siren or keypad beeps to determine appropriate response (refer to the control panel installation www.2gig.com instructions). 05/19/09 4. Exit sensor test mode. ©2009


Document Created: 2009-08-27 21:51:48
Document Modified: 2009-08-27 21:51:48
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC