User Manual (Statements)

FCC ID: WBV-BR100

Users Manual

Download: PDF
FCCID_1572201

Aerohive HiveAP Compliance Information Federal Communication Commission Interference Only attach antennas that are certified for use with this device. Replacing antennas with unauthorized, high-gain antennas greatly increases the risk of Statement interference and invalidates the FCC certification. Aerohive products (FCC models, AH-AP-110-N-FCC, AH-AP-120-N-FCC, AH-AP-170-N-FCC, AH-AP-320-N-FCC, AH-AP-330-N-FCC, AH-AP-340-N-FCC , Industry Canada AH-AP-350-N-FCC, AH-BR100-N-FCC) comply with part 15 of the FCC Rules Note: The term "IC" before the radio certification number signifies that when operating under the following restrictions: (1) they do not cause harmful Industry Canada technical specifications were met. interference, and (2) they must accept any RF interference received, including interference that might cause an unwanted impact on their operation. Products that show an Industry Canada identifier on the product label (IC HiveAP 170, 320, 330, 340, BR100, BR200 and 350) can be operated in Canada This equipment has been tested and found to comply with the limits for a Class under the following restrictions: B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a This device complies with RSS-210 of the Industry Canada Rules. Operation is residential installation. This equipment generates uses and can radiate radio subject to the following two conditions: (1) This device may not cause frequency energy and, if not installed and used in accordance with the harmful interference, and (2) this device must accept any interference instructions, may cause harmful interference to radio communications. received, including interference that may cause undesired operation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or IMPORTANT NOTE: television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the IC Radiation Exposure Statement following measures: Radiation Exposure Statement: This equipment complies with IC radiation • Reorient or relocate the receiving antenna exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between • Increase the separation between the equipment and receiver the radiator and your body. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected The HiveAP 170 has been designed to operate with an antenna having a Dipole maximum gain of 5 dBi. Antenna having a higher gain is strictly prohibited per • Consult the dealer or an experienced radio/TV technician for help regulations of Industry Canada. The required antenna impedance is 50 ohms. FCC Caution: Any changes or modifications not expressly approved by the Under Industry Canada regulations, this radio transmitter may only operate party responsible for compliance could void the user's authority to operate this using an antenna of a type and maximum (or lesser) gain approved for the equipment. transmitter by Industry Canada. To reduce potential radio interference to This device complies with Part 15 of the FCC Rules. Operation is subject to the other users, the antenna type and its gain should be so chosen that the following two conditions: (1) This device may not cause harmful interference, equivalent isotropically radiated power (E.I.R.P) is not more than that and (2) this device must accept any interference received, including necessary for successful communication. interference that may cause undesired operation. This radio transmitter (IC: 7774A-HIVEAP170 / Model: HiveAP 170) has been In compliance with FCC Part 15 regulations, the HiveAP automatically approved by Industry Canada to operate with the antenna types listed below discontinues transmission if there is no valid information to transmit or if there with the maximum permissible gain and required antenna impedance for each is an operational failure. antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited Important: FCC Regulatory Warning Notices for use with this device. HiveAP 110, 120, 320, 330, 340, 350 devices are restricted to indoor use due to Caution: The device for the band 5150-5250 MHz is only for indoor usage to their operation in 5 GHz frequencies, which are shared by mobile satellite reduce potential for harmful interference to co-channel mobile satellite systems and government radar systems. The FCC requires that these products systems. only be used indoors to reduce the potential for harmful interference with co-channel radar that might be operating in the 5.25-5.35 or 5.47-5.725 GHz High power radars are allocated as primary users (meaning they have priority) frequency ranges in the same area. The conflicting activity of radar stations of 5250-5350 MHz and 5650-5850 MHz and these radars could cause and these devices can cause interference or damage to each other. In interference and/or damage to LE-LAN devices. addition, these devices have a radar detection function that might interrupt The band from 5600-5650 MHz will be disabled by the proprietary software normal operations when they detect a radar signal. To reduce the risk of during the manufacturing and which cannot be changed by the end user. interference even further, installing these devices away from windows is recommended. HiveAP 170 devices operating within the 5.15-5.25 GHz frequency range are restricted to indoor environments. Note: Le terme “IC” précédant le numéro de certification radio signifie que les The FCC region code is set in the device during the manufacturing process, the spécifications techniques de l’Industrie du Canada ont été respectées. option to set it to any region other than FCC is disabled, and the country code Les produits indiquant un identifiant d’Industrie du Canada sur leur étiquette selection function has been completely removed from all U.S. models. It is (IC: 7774A-HiveAP170) peuvent être exploités au Canada dans le cadre des impossible for the end user to change the region to anything other than FCC. restrictions suivantes: FCC Radiation Exposure Statement Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada This equipment complies with FCC radiation exposure limits set forth for an applicable aux appareils radio exempts de licence. Son fonctionnement uncontrolled environment. This equipment should be installed and operated est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas with a minimum distance of 20 centimeters (8 inches) between the radiator produire de brouillage préjudiciable, et (2) ce dispositif doit accepter and your body. This transmitter must not be co-located or operating in tout brouillage reçu, y compris un brouillage susceptible de provoquer un conjunction with any other antenna or transmitter. fonctionnement indésirable. The availability of some specific channel and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by end user. © 2011 Aerohive Networks, Inc. All rights reserved. 330033-10 Rev. B

Aerohive HiveAP Compliance Information 2 NOTE IMPORTANTE: Generic standard to demonstrate the compliance of electronic and electrical apparatus with the basic restrictions related to human Déclaration d'exposition aux radiations: Cet équipement est conforme exposure to electromagnetic fields (0 Hz - 300 GHz) aux limites d'exposition aux rayonnements IC établies pour un • EN 300 328 V1.7.1: 2006 environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de Electromagnetic compatibility and Radio spectrum Matters (ERM); rayonnement et votre corps. Wideband Transmission systems; Data transmission equipment operating in the 2.4 GHz ISM band and using spread spectrum modulation Le point d’accès HiveAP170 a été conçu pour fonctionner avec une Dipole techniques; Harmonized EN covering essential requirements under article antenne ayant un gain maximal de dBi 5. Une antenne à gain plus élevé est 3.2 of the R&TTE Directive strictement interdite par les règlements d'Industrie Canada. L'impédance d'antenne requise est de 50 ohms. • EN 301 893 V1.5.1: 2008 Conformément à la réglementation d'Industrie Canada, le présent émetteur Broadband Radio Access Networks (BRAN); 5 GHz high performance RLAN; radio peutfonctionner avec une antenne d'un type et d'un gain maximal (ou Harmonized EN covering essential requirements of article 3.2 of the inférieur) approuvé pourl'émetteur par Industrie Canada. Dans le but de R&TTE Directive réduire les risques de brouillage radioélectriqueà l'intention des autres • EN 301 489-1 V1.8.1: 2008 utilisateurs, il faut choisir le type d'antenne et son gain de sorte que lapuissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité Electromagnetic Compatibility and Radio Spectrum Matters (ERM); nécessaire àl'établissement d'une communication satisfaisante. Electromagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements Le présent émetteur radio (IC: 7774A-HIVEAP170 / Model: HiveAP 1700) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne • EN 301 489-17 V2.1.1: 2009 énumérés ci-dessous et ayant un gain admissible maximal et l'impédance Electromagnetic Compatibility and Radio spectrum Matters (ERM); requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette Electromagnetic Compatibility (EMC) standard for radio equipment and liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement services; Part 17: Specific conditions for 2.4 GHz wideband transmission interdits pour l'exploitation de l'émetteur. systems and 5 GHz high performance RLAN equipment Avertissement: Le dispositif fonctionnant dans la bande 5150-5250 MHz les The HiveAP 170, 330, and 350 are 5 GHz wideband transmission systems risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant (transceivers), intended for use in all EU member states and EFTA countries, les mêmes canaux. except in France and Italy where restrictive use applies. Les utilisateurs de radars de haute puissance sont désignés utilisateurs In Italy the end-user should apply for a license at the national spectrum principaux (c.-à-d., qu'ils ont la priorité) pour les bandes 5250-5350 MHz et authorities in order to obtain authorization to use this equipment for setting 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des up outdoor radio links and/or for supplying public access to dommages aux dispositifs LAN-EL. telecommunications and/or network services. La bande de frequence de 5600-5650MHz devra etre desactivee par logiciel These devices may not be used for setting up outdoor radio links in France and lors de la conception et ne devra comporter aucune possibilite de modification in some areas the RF output power may be limited to 10 mW EIRP in the par l'utilisateur final. frequency range of 2454–2483.5 MHz For detailed information the end-user should contact the national spectrum authority in France. Declarations of conformity, compliance statements, and other regulatory Wi-Fi Certification documentation are available at www.aerohive.com/support. The Wi-Fi CERTIFIED™ Logo is a certification mark of the Wi-Fi Alliance®. The HiveAP 20, 100, 300 series have been certified for WPA™, WPA2™, WMM® (Wi-Fi Multimedia™), WMM Power Save, IEEE 802.11d, IEEE 802.11h, and the WEEE and RoHS Compliance following types of EAP (Extensible Authentication Protocol): Aerohive Networks products have been reviewed, analyzed and found to be in compliance with the European Union (EU) directive for Waste Electrical and • EAP-TLS • EAP-SIM Electronic Equipment (WEEE) and with the EU directive for the Restriction of Hazardous Substances (RoHS). • EAP-TTLS/MSCHAPv2 • EAP-AKA WEEE Collection Programs in the U.S. and EU • PEAPv0/EAP-MSCHAPv2 • EAP-FAST At end of life, customers are requested to contact Aerohive to make arrangements for WEEE collection of their products. The Aerohive collection center in the U.S. is at the following address: • PEAPv1/EAP-GTC Aerohive Inc. 330 Gibraltar Drive The HiveAP 100 and 300 series have also been certified for short guard interval Sunnyvale, CA 94089 and 40-MHz operation in the 5-GHz band. Telephone: 408-510-6100 Contact: Technical Support, weee@aerohive.com EC Conformance Declaration Aerohive, in association with M-Cubed LLC, also has a collection center at the following address in Germany, a member state of the European Union: Marking by the above symbol indicates compliance with the Essential EXTRABYTE - M Cubed LLC Requirements of the R&TTE Directive of the European Union (1999/5/EC). The Klopstock Strasse #8 HiveAP 110, 120, 320, and 340 platforms meet the following conformance 33613 BIELEFELD standards: Telephone: 49-521-882245 • EN 60950-1 (IEC 60950-1) 2nd edition - Product Safety Contact: Mr. Andreas Budde • EN 301 893 - Technical requirements for 5 GHz radio equipment • EN 300 328 - Technical requirements for 2.4 GHz radio equipment Countries of Operation and Conditions • EN 301 489-1 / EN 301 489-17 - EMC requirements for radio equipment of Use in the European Community The HiveAP 170, 330, and 350 platforms comply with the essential HiveAPs are intended to be operated in all countries of the European requirements of the R&TTE Directive 1999/5/EC. The following test methods Community. Requirements for indoor vs. outdoor operation, license have been applied to prove presumption of conformity with the essential requirements and allowed channels of operation apply in some countries as requirements of the R&TTE Directive 1999/5/EC: described below. • EN 60950-1:2006+A11:2009+A1:2010 • Before operating a HiveAP, the admin or installer must properly enter the current country code as described in Aerohive product documentation. Safety of Information Technology Equipment Note to U.S. model owners: To comply with U.S. FCC regulations, the • EN 50385: 2002 country selection function has been completely removed from all U.S. models. The above function is for non-U.S. models only. © 2011 Aerohive Networks, Inc. All rights reserved. 330033-10 Rev. B

Aerohive HiveAP Compliance Information 3 • HiveAPs automatically limit the allowable channels determined by the current country of operation. Incorrectly entering the country of Declaration of Conformity in Languages operation might result in illegal operation and cause harmful of the European Community interference to other systems. The admin is obligated to ensure HiveAPs are operating according to the channel limitations, indoor/outdoor Czech Aerohive tímto prohlašuje, že tento Radio LAN device restrictions and license requirements for each European Community country as described in this section. je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. • HiveAPs can be operated indoors or outdoors in all countries of the European Community using the 2.4 GHz band: Channels 1-13, except Danish Undertegnede Aerohive erklærer herved, at følgende where noted below: udstyr Radio LAN device overholder de væsentlige krav – In Italy and Luxembourg, you must apply for a license from the og øvrige relevante krav i direktiv 1999/5/EF. national spectrum authority to operate a HiveAP outside your own premises and for public use or service. Dutch Hierbij verklaart Aerohive dat het toestel Radio LAN – In Belgium outdoor operation is only permitted using the 2.46 to device in overeenstemming is met de essentiële eisen 2.4835 GHz band: Channel 13. en de andere relevante bepalingen van richtlijn 1999/5/EG. – In France outdoor operation is limited to the 2.454 to 2.4835 GHz band (channels 8 to 13) at a maximum of 10 mW EIRP (effective isotropic English Hereby, Aerohive, declares that this Radio LAN device radiated power). is in compliance with the essential requirements and – In Norway, the 2.4 GHz band cannot be used outdoors within a 20-km other relevant provisions of Directive 1999/5/EC. radius of the center of Ny-Ålesund. Estonian – In Russia, the 2.4 GHz band is for indoor use only. Käesolevaga kinnitab Aerohive seadme Radio LAN device vastavust direktiivi 1999/5/EÜ põhinõuetele ja • Because radar systems use some bands in the 5 GHz spectrum, WLAN nimetatud direktiivist tulenevatele teistele devices operating in these bands must use DFS (Dynamic Frequency asjakohastele sätetele. Selection) to detect radar activity and switch channels automatically to avoid interfering with radar operations. For the ETSI region, the HiveAP 300 series is certified for the latest ETSI EN 301 893 v1.5.1 DFS Finnish Valmistaja Aerohive vakuuttaa täten että Radio LAN requirements and can use DFS channels 52 to 140 (5.26 GHz to 5.32 GHz, device tyyppinen laite on direktiivin 1999/5/EY oleel- and 5.5 GHz to 5.7 GHz). To comply with ETSI regulations when deploying listen vaatimusten ja sitä koskevien direktiivin muiden a HiveAP 300 series device outdoors, set the 5 GHz radio to operate on ehtojen mukainen. the DFS channels and enable DFS. When deploying a HiveAP 300 series device indoors, then the 5 GHz radio can also use channels 36 to 48 as French Par la présente Aerohive déclare que cet appareil Radio well as the DFS channels. The maximum transmit power for channels LAN device est conforme aux exigences essentielles et from 36 to 48 is 17 dBm in the ETSI region. Because this maximum is aux autres dispositions relatives à la directive enforced by HiveOS, the HiveAP automatically limits the power to 17 dBm 1999/5/CE. even if the setting is greater than that. • The availability of some specific channels and/or operational frequency German Hiermit erklärt Aerohive, dass sich dieses Radio LAN bands are country dependent and are firmware programmed at device in Übereinstimmung mit den grundlegenden installation to match the intended destination. The firmware setting is Anforderungen und den anderen relevanten Vorschrif- accessible by the end user. Some national restrictions are noted below: ten der Richtlinie 1999/5/EG befindet". (BMWi) – In Italy and Luxembourg, you must apply for a license from the national spectrum authority to operate a HiveAP outside your own Greek premises and for public use or service in the 5.15 to 5.35 GHz band (channels 36 to 64) and 5.47 to 5.725 GHz band (channels 100 to 140). – In Russia, you can only use the 5.15 to 5.35 GHz band at 100 mW (20 Hungarian Alulírott, Aerohive nyilatkozom, hogy a Radio LAN dBm) indoors, in closed industrial and warehouse areas, and on board aircraft for local network and crew communications during all stages device megfelel a vonatkozó alapvetõ köve- of a flight and for public WLAN access only at an altitude of 3000 telményeknek és az 1999/5/EC irányelv egyéb meters or higher. You can only use the 5.65 to 5.825 GHz band with elõírásainak. 100 mW EIRP on board aircraft at an altitude of 3000 meters or higher. Italian Con la presente Aerohive dichiara che questo Radio LAN device è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latvian Ar šo Aerohive deklarē, ka Radio LAN device atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem. Lithuanian Šiuo Aerohive deklaruoja, kad šis Radio LAN device atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Maltese Hawnhekk, Aerohive, jiddikjara li dan Radio LAN device jikkonforma mal-ħtiġijiet essenzjali u ma provvedi- menti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Polish Niniejszym Aerohive oświadcza, że Radio LAN device jest zgodne z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Portuguese Aerohive declara que este Radio LAN device está conforme com os requisitos essenciais e outras dispo- sições da Directiva 1999/5/CE. © 2011 Aerohive Networks, Inc. All rights reserved. 330033-10 Rev. B

Aerohive HiveAP Compliance Information 4 Slovenian Aerohive izjavlja, da je ta Radio LAN device v skladu z Europe The supply plug must comply with CEE7/7 ("SCHUKO"). bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES. The mains cord must be <HAR> or <BASEC> marked and Spanish Por medio de la presente Aerohive declara que el Radio be of type HO3VVF3GO.75 (minimum). LAN device cumple con los requisitos esenciales y IEC-320 receptacle. cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Veuillez lire attentivement les informations de sécurité relatives à Swedish Härmed intygar Aerohive att denna Radio LAN device l'installation d'un point d'accès HiveAP. står I överensstämmelse med de väsentliga egenskap- Avertissement: L'installation et la dépose de points d'accès HiveAP doivent skrav och övriga relevanta bestämmelser som framgår être effectuées uniquement par un personnel qualifié. av direktiv 1999/5/EG. • Les points d'accès HiveAP doivent être connectés sur le secteur par une prise électrique munie de terre (masse) afin de respecter les standards HiveAP Safety Compliance internationaux de sécurité. Power Cord Safety • Ne jamais connecter des points d'accès HiveAP à une alimentation électrique non-pourvue de terre (masse). Please read the following safety information carefully before installing a HiveAP. • Le boitier d'alimentation (connecté directement au point d'accès) doit être compatible avec une entrée électrique de type EN 60320/IEC 320. Warning: Installation and removal of HiveAPs must be carried out by qualified • La prise secteur doit se trouver à proximité du point d'accès HiveAP et personnel only. facilement accessible. Vous ne pouvez mettre hors tension un point • HiveAPs must be connected to an earthed (grounded) outlet to comply d'accès HiveAP qu'en débranchant son alimentation électrique au niveau with international safety standards. de cette prise. • Do not connect HiveAPs to an A.C. outlet (power supply) without an earth • Pour des raisons de sécurité, le point d'accès HiveAP fonctionne à une (ground) connection. tension extrêmement basse, conformément à la norme IEC 60950. Les • The appliance coupler (the connector to the unit and not the wall plug) conditions de sécurité sont valables uniquement si l'équipement auquel must have a configuration for mating with an EN 60320/IEC 320 appliance le point d'accès HiveAP est raccordé fonctionne également selon cette inlet. norme. • The socket outlet must be near the HiveAP and easily accessible. You can • Un point d'accès HiveAP alimenté par son interface réseau Ethernet en only remove power from a HiveAP by disconnecting the power cord from mode POE (Power over Ethernet) doit être physiquement dans le même the outlet. bâtiment que l'équipement réseau qui lui fournit l'électricité. • HiveAPs operate under SELV (Safety Extra Low Voltage) conditions France et Pérou uniquement: according to IEC 60950. The conditions are only maintained if the Un point d'accès HiveAP ne peut pas être alimenté par un dispositif à equipment to which they are connected also operates under SELV impédance à la terre. Si vos alimentations sont du type impédance à la terre, conditions. alors le point d'accès HiveAP doit être alimenté par une tension de 230 V • A HiveAP receiving power through its PoE (Power over Ethernet) interface (2P+T) via un transformateur d'isolement à rapport 1:1, avec le neutre must be in the same building as the equipment from which it receives connecté directement à la terre (masse). power. France and Peru only: Cordon électrique - Il doit être agréé dans le pays d'utilisation HiveAPs cannot be powered from IT* supplies. If your supplies are of IT type, Etats-Unis Le cordon doit avoir reçu l'homologation des UL et un then a HiveAP must be powered by 230 V (2P+T) via an isolation transformer et Canada certificat de la CSA. ratio 1:1, with the secondary connection point labelled Neutral, connected directly to earth (ground). *Impédance à la terre Les spécifications minimales pour un cable flexible Important! Before making connections, make sure you have the correct cord - AWG No. 18, ou AWG No. 16 pour un cable de longueur set. Check it (read the label on the cable) against the description in this inférieure à 2 mètres. section. - Type SV ou SJ - 3 conducteurs Power Cord Set Le cordon doit être en mesure d'acheminer un courant U.S.A. The cord set must be UL/CSA/NRTL approved and nominal d'au moins 10 A. and Canada certified. La prise femelle de branchement doit être du type à mise à Minimum specifications for the flexible cord: la terre (mise à la masse) et respecter la configuration - No. 18 AWG not longer than 2 meters, or 16 AWG NEMA 5-15P (15 A, 125 V) ou NEMA 6-15P (15 A, 250 V). - Type SV or SJ - 3-conductor Danemark La prise mâle d'alimentation doit respecter la section 107-2 The cord set must have a rated current capacity of at D1 de la norme DK2 1a ou DK2 5a. least 10 A. Suisse La prise mâle d'alimentation doit respecter la norme SEV/ASE 1011. The attachment plug must be an earth-grounding type with NEMA 5-15P (15 A, 125 V) or NEMA 6-15 (15 A, 250 Europe La prise secteur doit être conforme aux normes CEE 7/7 V) configuration. ("SCHUKO"). LE cordon secteur doit porter la mention <HAR> ou <BASEC> Denmark The supply plug must comply with Section 107-2-D1, et doit être de type HO3VVF3GO.75 (minimum). Standard DK2-1a or DK2-5a. Switzerland The supply plug must comply with SEV/ASE 1011. Bitte unbedingt vor dem Einbauen des HiveAP die folgenden Sicherheitsanweisungen durchlesen. U.K. The supply plug must comply with BS1363 (3-pin 13 A) Warnung: Die Installation und der Ausbau des Geräts darf nur durch and be fitted with a 5 A fuse that complies with BS1362. Fachpersonal erfolgen. The mains cord must be <HAR> or <BASEC> marked and • Das Gerät sollte nicht an eine ungeerdete Wechselstromsteckdose be of type HO3VVF3GO.75 (minimum). angeschlossen werden. • Das Gerät muß an eine geerdete Steckdose angeschlossen werden, welche die internationalen Sicherheitsnormen erfüllt. © 2011 Aerohive Networks, Inc. All rights reserved. 330033-10 Rev. B

Aerohive HiveAP Compliance Information 5 • Der Gerätestecker (der Anschluß an das Gerät, nicht der Ce produit est destine a un usage specifique et doit etre installe par un Wandsteckdosenstecker) muß einen gemäß EN 60320/IEC 320 personnel qualifie maitrisant les radiofrequences et les regles s'y konfigurierten Geräteeingang haben. rapportant. L'installation et les reglages ne doivent pas etre modifies par • Die Netzsteckdose muß in der Nähe des Geräts und leicht zugänglich sein. l'utilisateur final. Die Stromversorgung des Geräts kann nur durch Herausziehen des 2. Emplacement d'installation Gerätenetzkabels aus der Netzsteckdose unterbrochen werden. En usage normal, afin de respecter les exigences reglementaires • Der Betrieb dieses Geräts erfolgt unter den SELV-Bedingungen concernant l'exposition aux radiofrequences, ce produit doit etre installe (Sicherheitskleinstspannung) gemäß IEC 60950. Diese Bedingungen sind de facon a respecter une distance de 40 cm entre l'antenne emettrice et nur gegeben, wenn auch die an das Gerät angeschlossenen Geräte unter les personnes. SELV-Bedingungen betrieben werden. 3. Antenn externe. Utiliser uniiquement les antennes approuvees par le fabricant. Stromkabel. Dies muss von dem Land, in dem es benutzt wird geprüft L'utilisation d'autres antennes peut conduire a un niveau de rayonnement werden: essentiel ou non essentiel depassant les niveaux limites definis par FCC/IC, ce qui est interdit. U.S.A. Der Cord muß das UL gepruft und war das CSA beglaubigt. 4. Procedure d'installation und Consulter le manuel d'installation. Kanada Das Minimum spezifikation fur der Cord sind: - Nu. 18 AWG - nicht mehr als 2 meter, oder 16 AWG. 5. Avertissement - Der typ SV oder SJ Choisir avec soin la position d'installation et s'assurer que la puissance de - 3-Leiter sortie ne depasse pas les limites en vigueur. La violation de cette regle peut conduire a de serieuses penalites federales. Der Cord muß haben eine strombelastbarkeit aus wenigstens 10 A. Korean ; ‘당해 무선설비는 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 Dieser Stromstecker muß hat einer erdschluss mit der typ NEMA 할 수 없음“ 5-15P (15A, 125V) oder NEMA 6-15P (15A, 250V) konfiguration. Country Certification Statements Danemark Dieser Stromstecker muß die ebene 107-2-D1, der standard DK2-1a oder DK2-5a Bestimmungen einhalten. The following HiveAPs have been certified by the specified regulatory agencies and authorities: HiveAP 330 Schweiz Dieser Stromstecker muß die SEV/ASE 1011Bestimmungen UAE: Telecommunication Regulatory Authority (TRA) einhalten. Registration Number: ER0072051/11 Dealer number: DA0070080/11 Europe Europe Das Netzkabel muß vom Typ HO3VVF3GO.75 (Mindes- tanforderung) sein und die Aufschrift <HAR> oder <BASEC> Mexico: Cofetel Cert. Number: RCPAEHI11-0892-A1 (valid 11/23/2012) tragen. Der Netzstecker muß die Norm CEE 7/7 erfüllen ("SCHUKO"). HiveAP 350 UAE: Telecommunication Regulatory Authority (TRA) Registration Number: ER0072044/11 Dealer number: DA0070080/11 HiveAP 170 Professional Installation Requirement Mexico: Cofetel Cert. Number: RCPAEHI11-0892 (valid 11/23/2012) Please be advised that due to the unique function supplied by this product, the device is intended for use with Aerohive software and licensed third-party HiveAP 340 software only. The product will be distributed through controlled distribution Saudi Arabia: Product Conformity Programme (PCP) channels, installed by trained professionals, and will not be sold directly to the Registration Number: KSA R-103282 general public through retail stores. Communications and Information Technology Commission (CITC) 1. Installation personal Number: 14408 This product is designed for a specific application and must be installed by qualified personnel with RF and related rule knowledge. The general HiveAP 320 user shall not attempt to install or change the device settings. Mexico: Cofetel Certification Number: RCPAEHI10-1206 2. Installation location NYCE/NOM Certification Number: 1002CE11218 To meet regulatory RF exposure requirements, the product shall be installed at a location where the radiating antenna in normal operating HiveAP 120 conditions can be kept at least 20cm from people. UAE: Telecommunication Regulatory Authority (TRA) 3. External antenna Registration Number: ER0070180/11 Dealer number: DA0070080/11 Use only antennas which have been approved by Aerohive Networks, Inc. Non-approved antennas may produce unwanted spurious or excessive RF Malaysia: SIRIM Type Approval Code: RAVG/92M/1010/S(10-1784) transmission, which is prohibited, and may violate the FCC/IC limit. Singapore: Infocomm Development Authority (IDA) 4. Installation procedure Registration Number: G1901-10 Please refer to installation manual for details. Saudi Arabia: Product Conformity Programme (PCP) 5. Warning Registration Number: KSA R-103282 Communications and Information Technology Commission (CITC) Please carefully select the installation position and make sure that the Number: 14405 final power output does not exceed the allowed limit. Violation of this limit could lead to serious federal penalties. HiveAP 170 Instructions d'installation professionnelle Liability Disclaimer Installation of Aerohive equipment must comply with local and national Veuillez noter que l'appareil etant dedie a une fonction unique, il doit etre electrical codes and with other regulations governing this type of installation. utilise avec Aerohive logiciel proprietaire. Ce produit sera propose par un Aerohive Networks, its channel partners, resellers, and distributors assume no reseau de distribution controle et installe par des professionels; il ne sera pas liability for personal injury, property damage, or violation of government propose au grand public par le reseau de la grande distribution. regulations that might arise from failing to comply with the instructions 1. Installation provided and appropriate electrical codes. © 2011 Aerohive Networks, Inc. All rights reserved. 330033-10 Rev. B


Document Created: 2011-11-02 11:17:05
Document Modified: 2011-11-02 11:17:05
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC