Test report

FCC ID: WAP2005

Test Report

Download: PDF
FCCID_2945382

Test Report FCC Part15 Subpart C Product Name : EZ-BLE PRoC Module Model No. : CYBLE-222014-01/CYBLE-222005-00 FCC ID : WAP2005 IC : 7922A-2005 Applicant : Cypress Semiconductor Corporation Address : 198 Champion Ct, San Jose, California 95134 United States Date of Receipt : Feb. 24, 2016 Test Date : Feb. 24, 2016 ~ Mar. 04, 2016 Issued Date : Mar. 04, 2016 Report No. : 1622078R-RF-US-P06V02 Report Version : V1.0 Note:The report was based on 1590279R,due to the update of BLE specification, we just update Radiated Emission, Radiated Emission Band Edge and Power Output. The test results relate only to the samples tested. The test results shown in the test report are traceable to the national/international standard through the calibration of the equipment and evaluated measurement uncertainty herein. This report must not be used to claim product endorsement by TAF or any agency of the government. The test report shall not be reproduced without the written approval of QuieTek Corporation.

~D> DEKRA Report No.: 1622078R—RF—US—PO6VO2 Test Report Certification Issued Date : Mar. 04, 2016 Report No. : 1622078R—RF—US—PO6V02 ny EKR A compa § P D Product Name EZ—BLE PRoC Module Applicant Cypress Semiconductor Corporation Address 198 Champion Ct, San Jose, California 95134 United States Manufacturer Wujiang Sigmatron Electronics Co., Ltd Address 386 Huahong Rd, Wujiang, Suzhou, Jiangsu, China Model No. CYBLE—222014—01/CYBLE—222005—00 FCC ID WAP2005 IC 7922A—2005 EUT Voltage DC 3.3V Applicable Standard FCC CFR Title 47 Part 15 Subpart C: 2015 ANSI C63.4: 2014; ANSI C63.10: 2013 KDB 558074 DO1 DTS Meas Guidance v03r03 Industry Canada RSS—Gen Issue 4 / RSS—247 Issue 1 Test Result Complied Performed Location Suzhou EMC Laboratory No.99 Hongye Rd., Suzhou Industrial Park, Suzhou, 215006, Jiangsu, China TEL: +86—512—6251—5088 / FAX: +86—512—6251—5098 Documented By /S(I:CQ/ hi (Senior Adm. Specialist: Alice Ni ) Reviewed By _ode_Zhan4 (Senior Engineer:-Jaék Zhang ) y—VPW Approved By (Engi\;\eeri@ Manager : Harry Zhao ) Page: 2 of 32

Report No.: 1622078R-RF-US-P06V02 Laboratory Information We, QuieTek Corporation, are an independent EMC and safety consultancy that was established the whole facility in our laboratories. The test facility has been accredited/accepted(audited or listed) by the following related bodies in compliance with ISO 17025, EN 45001 and specified testing scope: Taiwan R.O.C. : BSMI, NCC, TAF USA : FCC Japan : VCCI China : CNAS The related certificate for our laboratories about the test site and management system can be downloaded from QuieTek Corporation’s Web Site :http://www.quietek.com/tw/ctg/cts/accreditations.htm The address and introduction of QuieTek Corporation’s laboratories can be founded in our Web site : http://www.quietek.com/ If you have any comments, Please don’t hesitate to contact us. Our contact information is as below: HsinChu Testing Laboratory : No.75-2, 3rd Lin, Wangye Keng, Yonghxing Tsuen, Qionglin Shiang, Hsinchu County 307, Taiwan, R.O.C. TEL:+886-3-592-8858 / FAX:+886-3-592-8859 E-Mail : service@quietek.com LinKou Testing Laboratory : No.5-22, Ruishukeng, Linkou Dist., New Taipei City 24451, Taiwan, R.O.C. TEL : 886-2-8601-3788 / FAX : 886-2-8601-3789 E-Mail : service@quietek.com Suzhou Testing Laboratory : No.99 Hongye Rd., Suzhou Industrial Park, Suzhou, 215006, Jiangsu, China TEL : +86-512-6251-5088 / FAX : 86-512-6251-5098 E-Mail : service@quietek.com Page: 3 of 32

Report No.: 1622078R-RF-US-P06V02 TABLE OF CONTENTS Description Page 1. General Information ...................................................................................................... 6 1.1. EUT Description ............................................................................................................ 6 1.2. Mode of Operation ........................................................................................................ 8 1.3. Tested System Details .................................................................................................. 9 1.4. Configuration of Tested System .................................................................................. 10 1.5. EUT Exercise Software ............................................................................................... 11 2. Technical Test ............................................................................................................. 12 2.1. Summary of Test Result .............................................................................................. 12 2.2. Test Environment ........................................................................................................ 14 3. Radiated Emission ...................................................................................................... 15 3.1. Test Equipment ........................................................................................................... 15 3.2. Test Setup ................................................................................................................... 16 3.3. Limit ............................................................................................................................ 17 3.4. Test Procedure ............................................................................................................ 17 3.5. Uncertainty .................................................................................................................. 17 3.6. Test Result .................................................................................................................. 18 4. Radiated Emission Band Edge ................................................................................... 19 4.1. Test Equipment ........................................................................................................... 19 4.2. Test Setup ................................................................................................................... 20 4.3. Limit ............................................................................................................................ 20 4.4. Test Procedure ............................................................................................................ 20 4.5. Uncertainty .................................................................................................................. 21 4.6. Test Result .................................................................................................................. 22 5. Power Output .............................................................................................................. 30 5.1. Test Equipment ........................................................................................................... 30 5.2. Test Setup ................................................................................................................... 30 5.3. Limit ............................................................................................................................ 30 5.4. Test Procedure ............................................................................................................ 30 5.5. Uncertainty .................................................................................................................. 31 5.6. Test Result .................................................................................................................. 32 Page: 4 of 32

Report No.: 1622078R-RF-US-P06V02 History of This Test Report REPORT NO. VERSION DESCRIPTION ISSUED DATE 1622078R-RF-US-P06V02 V1.0 Initial Issued Report Mar. 04, 2016 Page: 5 of 32

Report No.: 1622078R-RF-US-P06V02 1. General Information 1.1. EUT Description Product Name EZ-BLE PRoC Module Model No. CYBLE-222005-00 Working Voltage DC 3.3V Bluetooth Specification V4.1 Frequency Range 2402- 2480 MHz Channel Number V4.1: 40 Channel Separation V4.1: 2MHz Type of Modulation V4.1: GFSK Data Rate V4.1: 1Mbps(GFSK) Model No. CYBLE-222014-01 Working Voltage DC 3.3V Bluetooth Specification V4.2 Frequency Range 2402- 2480 MHz Channel Number V4.2: 40 Channel Separation V4.2: 2MHz Type of Modulation V4.2: GFSK Data Rate V4.2: 1Mbps(GFSK) Antenna Type Reference to Antenna List Peak Antenna Gain Reference to Antenna List Note: 1.The Bluetooth version is 4.1&4.2 but only supports low energy mode. 2. Compared with CYBLE-222005-00, the main chip of CYBLE-222014-01 has upgraded the Bluetooth version from BLE 4.1 to BLE 4.2. Bluetooth Working Frequency of Each Channel: (For V4.1&V4.2) Channel Frequency Channel Frequency Channel Frequency Channel Frequency 00 2402 MHz 01 2404 MHz 02 2406 MHz 03 2408 MHz 04 2410 MHz 05 2412 MHz 06 2414 MHz 07 2416 MHz 08 2418 MHz 09 2420 MHz 10 2422 MHz 11 2424 MHz 12 2426 MHz 13 2428 MHz 14 2430 MHz 15 2432 MHz 16 2434 MHz 17 2436 MHz 18 2438 MHz 19 2440 MHz 20 2442 MHz 21 2444 MHz 22 2446 MHz 23 2448 MHz 24 2450 MHz 25 2452 MHz 26 2454 MHz 27 2456 MHz 28 2458 MHz 29 2460 MHz 30 2462 MHz 31 2464 MHz 32 2466 MHz 33 2468 MHz 34 2470 MHz 35 2472 MHz 36 2474 MHz 37 2476 MHz 38 2478 MHz 39 2480 MHz Page: 6 of 32

Report No.: 1622078R-RF-US-P06V02 Bluetooth Antenna List Antenna Manufacturer Model No. Peak Gain Ceramic Antenna N/A N/A 0.5dBi Page: 7 of 32

Report No.: 1622078R-RF-US-P06V02 1.2. Mode of Operation QuieTek has verified the construction and function in typical operation. All the test modes were carried out with the EUT in normal operation, which was shown in this test report and defined as: Test Mode Mode 1: Transmit-1Mbps(GFSK_BLE) Note: 1. Regards to the frequency band operation: the lowest､middle and highest frequency of channel were selected to perform the test, then shown on this report. 2. For portable device, radiated spurious emission was verified over X, Y, Z Axis, and shown the worst case on this report. 3. The reading values of all the test items contain cable loss. (Cable loss=0.5dBm) Page: 8 of 32

Report No.: 1622078R-RF-US-P06V02 1.3. Tested System Details The types for all equipments, plus descriptions of all cables used in the tested system (including inserted cards) are: Product Manufacturer Model No. Serial No. Power Cord 1 N/A N/A N/A N/A N/A Page: 9 of 32

Report No.: 1622078R-RF-US-P06V02 1.4. Configuration of Tested System Connection Diagram Signal Cable Type Signal cable Description N/A N/A N/A Page: 10 of 32

Report No.: 1622078R-RF-US-P06V02 1.5. EUT Exercise Software 1 Setup the EUT and simulators as shown on above. 2 Turn on the power of all equipment. Run the RF test software, and set the test mode and channel, then press OK to start continue 3 Transmit. Page: 11 of 32

Report No.: 1622078R-RF-US-P06V02 2. Technical Test 2.1. Summary of Test Result No deviations from the test standards Deviations from the test standards as below description: Test Performed Test Item Normative References Deviation Performed Radiated Emission FCC CFR Title 47 Part 15 Subpart C: 2015 Yes No Section 15.209 Radiated Emission Band Edge FCC CFR Title 47 Part 15 Subpart C: 2015 Yes No 15.247(d) Power Output FCC CFR Title 47 Part 15 Subpart C: 2015 Yes No Section 15.247(b)(3) Page: 12 of 32

Report No.: 1622078R-RF-US-P06V02 Test Performed Test Item Normative References Deviation Performed Radiated Emission RSS-Gen Issue 4 Yes No Section 8.9 Radiated Emission Band Edge RSS-247 Issue 1 Yes No Section A5.5 Power Output RSS-247 Issue 1 Yes No Section A5.4(4) Page: 13 of 32

Report No.: 1622078R-RF-US-P06V02 2.2. Test Environment Items Required (IEC 68-1) Actual Temperature (°C) 15-35 21 Humidity (%RH) 25-75 50 Barometric pressure (mbar) 860-1060 950-1000 Page: 14 of 32

Report No.: 1622078R-RF-US-P06V02 3. Radiated Emission 3.1. Test Equipment Radiated Emission / AC-2 Instrument Manufacturer Type No. Serial No. Cal. Due Date EMI Test Receiver R&S ESCI 100573 2016.03.28 Loop Antenna R&S HFH2-Z2 833799/003 2016.11.25 Bilog Antenna Teseq GmbH CBL6112D 27611 2016.10.10 Coaxial Cable Huber+Suhner SUCOFLEX 106 AC2-C 2016.03.01 Temperature/Humidity Meter Zhicheng ZC1-2 AC2-TH 2017.01.04 Radiated Emission / AC-5 Instrument Manufacturer Type No. Serial No. Cal. Due Date Spectrum Analyzer Agilent N9010A MY48030494 2016.05.12 Preamplifier Miteq NSP1800-25 1364185 2016.05.03 Preamplifier QuieTek AP-040G CHM-0906001 2016.05.03 Bilog Antenna Teseq GmbH CBL6112D 27612 2016.10.15 Broad-Band Horn Antenna Schwarzbeck BBHA9120D 499 2016.06.08 Broad-Band Horn Antenna Schwarzbeck BBHA9170 294 2016.04.10 Coaxial Cable Huber+Suhner SUCOFLEX 106 AC5-C1 2016.03.01 Coaxial Cable Huber+Suhner SUCOFLEX 106 AC5-C2 2016.03.01 Coaxial Cable Huber+Suhner SUCOFLEX 102 AC5-C3 2016.03.01 Temperature/Humidity Meter Zhicheng ZC1-2 AC5-TH 2017.01.04 Page: 15 of 32

Report No.: 1622078R-RF-US-P06V02 3.2. Test Setup Below 1GHz Test Setup: Above 1GHz Test Setup: Page: 16 of 32

Report No.: 1622078R-RF-US-P06V02 3.3. Limit FCC Part 15 Subpart C Paragraph 15.209 Frequency Distance Level (MHz) (m) (dBuV/m) 30 - 88 3 40 88 - 216 3 43.5 216 - 960 3 46 Above 960 3 54 Note 1: The lower limit shall apply at the transition frequency. Note 2: Distance refers to the distance in meters between the measuring instrument antenna and the closed point of any part of the device or system. Note 3: E field strength (dBuV/m) = 20 log E field strength (uV/m) 3.4. Test Procedure The EUT was setup according to ANSI C63.4, 2014 and tested according to KDB 558074 for compliance to FCC 47CFR 15.247 requirements. The EUT is placed on a turn table which is 0.8 meter above ground. The turn table is rotated 360 degrees to determine the position of the maximum emission level. The EUT was positioned such that the distance from antenna to the EUT was 3 meters. The antenna is scanned from 1 meter to 4 meters to find out the maximum emission level. This is repeated for both horizontal and vertical polarization of the antenna. In order to find the maximum emission, all of the interface cables were manipulated according to ANSI C63.4:2009 on radiated measurement. The resolution bandwidth below 1GHz setting on the field strength meter is 120 kHz and above 1GHz is 1MHz. The frequency range from 30MHz to 10th harmonic is checked. Note: When doing emission measurement above 1GHz, the horn antenna will be bended down a little (as horn antenna has the narrow beamwidth) in order to keeping the antenna in the “cone of radiation” of EUT. The 3dB beamwidth is 10~60 degrees for H-plane and 10~90 degrees for E-plane. 3.5. Uncertainty The measurement uncertainty above 1GHz is defined as ± 3.9 dB below 1GHz is defined as ± 3.8 dB Page: 17 of 32

Report No.: 1622078R-RF-US-P06V02 3.6. Test Result All of the test result shown indicates the worst case, and spectrum analyzer parameters setting as shown below: Peak detector: RBW = 1MHz, VBW = 3MHz, sweep time = 200ms; Average detector: RBW = 1MHz, VBW = 10Hz, sweep time = auto. Measure Level = Reading Level + Cable Loss + Antenna Factor - Preamplifier Gain Mode 1: Transmitter-1Mbps(GFSK_BLE) CH Antenna Frequency Reading Factor Measure Limit Margin Detector (MHz) Level (dB) Level (dBuV/m) (dB) (dBuV/m) (dBuV/m) H 4804.0 33.7 8.0 41.7 54(Note2) -12.3 PK V 4804.0 35.8 8.0 43.8 54(Note2) -10.2 PK H 7206.0 30.8 12.8 43.6 54(Note2) -10.4 PK 0 V 7206.0 31.6 12.8 44.4 54(Note2) -9.6 PK H 9608.0 29.1 16.1 45.2 54(Note2) -8.8 PK V 9608.0 29.0 16.1 45.1 54(Note2) -8.9 PK H 4880.0 33.2 8.2 41.4 54(Note2) -12.6 PK V 4880.0 33.6 8.2 41.8 54(Note2) -12.2 PK H 7320.0 30.1 13.0 43.1 54(Note2) -10.9 PK 19 V 7320.0 30.4 13.0 43.4 54(Note2) -10.6 PK H 9760.0 28.2 16.3 44.5 54(Note2) -9.5 PK V 9760.0 28.8 16.3 45.1 54(Note2) -8.9 PK H 4960.0 33.1 8.5 41.6 54(Note2) -12.4 PK V 4960.0 35.2 8.5 43.7 54(Note2) -10.3 PK H 7440.0 29.9 13.2 43.1 54(Note2) -10.9 PK 39 V 7440.0 31.5 13.2 44.7 54(Note2) -9.3 PK H 9920.0 29.1 16.1 45.2 54(Note2) -8.8 PK V 9920.0 28.8 16.1 44.9 54(Note2) -9.1 PK Note 1: The test trace is same as the ambient noise (the test frequency range: 9kHz~30MHz, 18GHz~25GHz), therefore no data appear in the report. 2: This limit applies for using average detector, if the test result on peak is lower than average limit, then average measurement needn’t be performed. Page: 18 of 32

Report No.: 1622078R-RF-US-P06V02 4. Radiated Emission Band Edge 4.1. Test Equipment Radiated Emission Band Edge / AC-5 Instrument Manufacturer Type No. Serial No. Cal. Due Date Spectrum Analyzer Agilent N9020A MY49100159 2016.03.30 Preamplifier Miteq NSP1800-25 1364185 2016.05.03 Preamplifier QuieTek AP-040G CHM-0906001 2016.05.03 Bilog Antenna Teseq GmbH CBL6112D 27612 2016.10.15 DRG Horn ETS-Lindgren 3117 00123988 2016.01.05 Coaxial Cable Huber+Suhner SUCOFLEX 106 AC5-C1 2016.03.01 Coaxial Cable Huber+Suhner SUCOFLEX 106 AC5-C2 2016.03.01 Coaxial Cable Huber+Suhner SUCOFLEX 102 AC5-C3 2016.03.01 EMI Receiver Agilent N9038A MY51210196 2016.08.07 Temperature/Humidity Meter Zhicheng ZC1-2 AC5-TH 2017.01.04 Note 1: All equipments are calibrated with traceable calibrations. Each calibration is traceable to the national or international standards. Page: 19 of 32

Report No.: 1622078R-RF-US-P06V02 4.2. Test Setup 4.3. Limit Radiated emissions which fall in the restricted bands, as defined in Section 15.205(a) of FCC part 15, must also comply with the radiated emission limits specified in Section 15.209(a) (see Section 15.205(c)). 4.4. Test Procedure According to ANSI C63.10: 2013. This test is required for any spurious emission or modulation product that falls in a Restricted Band, as defined in Section 15.205 of FCC part 15. It must be performed with the highest gain of each type of antenna proposed for use with the EUT. Use the following spectrum analyzer settings: Span = wide enough to fully capture the emission being measured RBW = 1 MHz for f ≧ 1 GHz, 100 kHz for f < 1GHz VBW ≧ RBW Sweep = auto Detector function = peak Trace = max hold Follow the guidelines in ANSI C63.4 with respect to maximizing the emission by rotating the EUT, measuring the emission while the EUT is situated in three orthogonal planes (if appropriate), adjusting the measurement antenna height and polarization, etc. A pre-amp and a high pass filter are required for this test, in order to provide the measuring system with Page: 20 of 32

Report No.: 1622078R-RF-US-P06V02 sufficient sensitivity. Allow the trace to stabilize. The peak reading of the emission, after being corrected by the antenna factor, cable loss, pre-amp gain, etc., is the peak field strength, which must comply with the limit specified in Section 15.35(b) of FCC part 15. Now set the VBW ≥ 1 / T (the minimum transmission duration), while maintaining all of the other instrument settings. This peak level, once corrected, must comply with the limit specified in Section 15.209 of FCC Part 15. If the emission on which a radiated measurement must be made is located at the edge of the authorized band of operation, then the alternative “marker-delta” method may be employed. 4.5. Uncertainty The measurement uncertainty above 1G is defined as ± 3.9 dB Page: 21 of 32

Report No.: 1622078R-RF-US-P06V02 4.6. Test Result Engineer: Scott Site: AC5 Time: 2016/03/02 - 10:13 Limit: FCC_Part15.209_RE(3m) Margin: 0 Probe: Horn_3117_00167055(1-18GHz) Polarity: Horizontal EUT: EZ-BLE PRoC Module Power: AC 120V/60Hz Note: Mode 1:Transmit at 2402MHz by BLE No Mark Frequency Measure Level Reading Level Over Limit Limit Factor Type (MHz) (dBuV/m) (dBuV) (dB) (dBuV/m) (dB) 1 2390.000 58.612 21.257 -15.388 74.000 37.355 PK 2 * 2401.675 92.559 55.217 18.559 74.000 37.342 PK Page: 22 of 32

Report No.: 1622078R-RF-US-P06V02 Engineer: Scott Site: AC5 Time: 2016/03/02 - 10:14 Limit: FCC_Part15.209_RE(3m) Margin: 0 Probe: Horn_3117_00167055(1-18GHz) Polarity: Horizontal EUT: EZ-BLE PRoC Module Power: AC 120V/60Hz Note: Mode 1:Transmit at 2402MHz by BLE No Mark Frequency Measure Level Reading Level Over Limit Limit Factor Type (MHz) (dBuV/m) (dBuV) (dB) (dBuV/m) (dB) 1 2390.000 39.328 1.973 -14.672 54.000 37.355 AV 2 * 2402.008 72.029 34.687 18.029 54.000 37.341 AV Page: 23 of 32

Report No.: 1622078R-RF-US-P06V02 Engineer: Scott Site: AC5 Time: 2016/03/02 - 10:16 Limit: FCC_Part15.209_RE(3m) Margin: 0 Probe: Horn_3117_00167055(1-18GHz) Polarity: Vertical EUT: EZ-BLE PRoC Module Power: AC 120V/60Hz Note: Mode 1:Transmit at 2402MHz by BLE No Mark Frequency Measure Level Reading Level Over Limit Limit Factor Type (MHz) (dBuV/m) (dBuV) (dB) (dBuV/m) (dB) 1 2383.198 56.517 19.160 -17.483 74.000 37.357 PK 2 2390.000 57.165 19.810 -16.835 74.000 37.355 PK 3 * 2401.675 90.698 53.356 16.698 74.000 37.342 PK Page: 24 of 32

Report No.: 1622078R-RF-US-P06V02 Engineer: Scott Site: AC5 Time: 2016/03/02 - 10:17 Limit: FCC_Part15.209_RE(3m) Margin: 0 Probe: Horn_3117_00167055(1-18GHz) Polarity: Vertical EUT: EZ-BLE PRoC Module Power: AC 120V/60Hz Note: Mode 1:Transmit at 2402MHz by BLE No Mark Frequency Measure Level Reading Level Over Limit Limit Factor Type (MHz) (dBuV/m) (dBuV) (dB) (dBuV/m) (dB) 1 2390.000 39.295 1.940 -14.705 54.000 37.355 AV 2 * 2401.960 70.808 33.466 16.808 54.000 37.341 AV Page: 25 of 32

Report No.: 1622078R-RF-US-P06V02 Engineer: Scott Site: AC5 Time: 2016/03/02 - 10:20 Limit: FCC_Part15.209_RE(3m) Margin: 0 Probe: Horn_3117_00167055(1-18GHz) Polarity: Horizontal EUT: EZ-BLE PRoC Module Power: AC 120V/60Hz Note: Mode 1:Transmit at 2480MHz by BLE No Mark Frequency Measure Level Reading Level Over Limit Limit Factor Type (MHz) (dBuV/m) (dBuV) (dB) (dBuV/m) (dB) 1 * 2479.914 88.912 51.427 14.912 74.000 37.485 PK 2 2483.500 65.433 27.922 -8.567 74.000 37.511 PK Page: 26 of 32

Report No.: 1622078R-RF-US-P06V02 Engineer: Scott Site: AC5 Time: 2016/03/02 - 10:20 Limit: FCC_Part15.209_RE(3m) Margin: 0 Probe: Horn_3117_00167055(1-18GHz) Polarity: Horizontal EUT: EZ-BLE PRoC Module Power: AC 120V/60Hz Note: Mode 1:Transmit at 2480MHz by BLE No Mark Frequency Measure Level Reading Level Over Limit Limit Factor Type (MHz) (dBuV/m) (dBuV) (dB) (dBuV/m) (dB) 1 * 2480.079 69.764 32.277 15.764 54.000 37.486 AV 2 2483.500 39.552 2.041 -14.448 54.000 37.511 AV Page: 27 of 32

Report No.: 1622078R-RF-US-P06V02 Engineer: Scott Site: AC5 Time: 2016/03/02 - 10:22 Limit: FCC_Part15.209_RE(3m) Margin: 0 Probe: Horn_3117_00167055(1-18GHz) Polarity: Vertical EUT: EZ-BLE PRoC Module Power: AC 120V/60Hz Note: Mode 1:Transmit at 2480MHz by BLE No Mark Frequency Measure Level Reading Level Over Limit Limit Factor Type (MHz) (dBuV/m) (dBuV) (dB) (dBuV/m) (dB) 1 * 2480.200 86.938 49.450 12.938 74.000 37.487 PK 2 2483.500 63.868 26.357 -10.132 74.000 37.511 PK Page: 28 of 32

Report No.: 1622078R-RF-US-P06V02 Engineer: Scott Site: AC5 Time: 2016/03/02 - 10:23 Limit: FCC_Part15.209_RE(3m) Margin: 0 Probe: Horn_3117_00167055(1-18GHz) Polarity: Vertical EUT: EZ-BLE PRoC Module Power: AC 120V/60Hz Note: Mode 1:Transmit at 2480MHz by BLE No Mark Frequency Measure Level Reading Level Over Limit Limit Factor Type (MHz) (dBuV/m) (dBuV) (dB) (dBuV/m) (dB) 1 * 2480.079 68.245 30.758 14.245 54.000 37.486 AV 2 2483.500 39.521 2.010 -14.479 54.000 37.511 AV Page: 29 of 32

Report No.: 1622078R-RF-US-P06V02 5. Power Output 5.1. Test Equipment Power Output / TR-8 Instrument Manufacturer Type No. Serial No. Cal. Due Date Wideband Peak Power Meter Anritsu ML2495A 0905006 2016.11.10 Power Sensor Anritsu MA2411B 0846014 2016.11.10 Temperature/Humidity Meter zhicheng ZC1-2 TR8-TH 2016.04.09 Note: All equipments are calibrated with traceable calibrations. Each calibration is traceable to the national or international standards. 5.2. Test Setup 5.3. Limit The maximum peak power shall be less 1 Watt (30dBm). Note: the conducted output power limit specified above is based on the use the antennas with directional gains that do not exceed 6 dBi are used, the conducted output power from the intentional radiator shall be reduced below the stated values above, as appropriate, by the amount in dB that the directional gain of antenna exceeds 6 dBi. For DTSs employing digital modulation techniques operating in the bands 902-928 MHz and 2400-2483.5 MHz, the maximum peak conducted output power shall not exceed 1W. Except as provided in Section 5.4(5), the e.i.r.p. shall not exceed 4 W. 5.4. Test Procedure Page: 30 of 32

Report No.: 1622078R-RF-US-P06V02 The EUT was tested according to DTS test procedure of ANSI C63.10 for compliance to FCC 47CFR 15.247 requirements. The maximum conducted output power using ANSI C63.10 section 11.9.1.1 peak power meter method. 1. Power meter and sensor’s minimum video bandwidth is 50MHz, larger than occupied bandwidth; 2. Fast responding diode sensors respond immediately to changes in power level to reduce total test time. 3. Use peak detector to test. 5.5. Uncertainty The measurement uncertainty is defined as ± 1.27 dB Page: 31 of 32

Report No.: 1622078R-RF-US-P06V02 5.6. Test Result Product : EZ-BLE PROC MODULE Test Item : Power Output Test Site : TR8 Test Mode : Mode 1: Transmit-1Mbps(GFSK_BLE) Channel Frequency Power Output Output Power Limit Result No. (MHz) (dBm) (dBm) 00 2402 -1.81 30.00 Pass 19 2440 -1.94 30.00 Pass 39 2480 -1.69 30.00 Pass The End Page: 32 of 32


Document Created: 2016-03-18 15:25:01
Document Modified: 2016-03-18 15:25:01
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC