User Manual

FCC ID: WAP-CY5677

Users Manual

Download: PDF
FCCID_3045283

CY8CKIT-042-BLE-A Bluetooth® Low Energy (BLE) Pioneer Kit Guide Doc. # 002-11468 Rev. *A Cypress Semiconductor 198 Champion Court San Jose, CA 95134-1709 Phone (USA): 800.858.1810 Phone (Intnl): +1.408.943.2600 www.cypress.com

Copyrights Copyrights © Cypress Semiconductor Corporation, 2016. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC ("Cypress"). This document, including any software or firmware included or referenced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby grants you under its copyright rights in the Software, a personal, non- exclusive, nontransferable license (without the right to sublicense) (a) for Software provided in source code form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units. Cypress also grants you a personal, non-exclusive, nontransferable, license (without the right to sublicense) under those claims of Cypress's patents that are infringed by the Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software solely to the minimum extent that is necessary for you to exercise your rights under the copyright license granted in the previous sentence. Any other use, reproduction, modification, translation, or compilation of the Software is prohibited. CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress products are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the device or system could cause personal injury, death, or property damage ("Unintended Uses"). A critical component is any component of a device or system whose failure to perform can be reasonably expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and Company shall and hereby does release Cypress from any claim, damage, or other liability arising from or related to all Unintended Uses of Cypress products. Company shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products. Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners. CySmart, F-RAM, PRoC, Programmable System-on-Chip, and PSoC Creator are trademarks of Cypress Semiconductor Corporation. CY8CKIT-042-BLE-A Bluetooth® Low Energy (BLE) Pioneer Kit Guide, Doc. # 002-11468 Rev. *A 2

Contents Safety Information 6 1. Introduction 10 1.1 Kit Contents ...............................................................................................................1 1 1.2 BLE Pioneer Baseboard Details ................................................................................12 1.3 PSoC Creator ............................................................................................................14 1.3.1 PSoC Creator Code Examples ......................................................................15 1.3.2 Kit Code Examples.........................................................................................16 1.3.3 PSoC Creator Help ........................................................................................16 1.3.4 Component Datasheets .................................................................................17 1.4 Getting Started...........................................................................................................17 1.5 Additional Learning Resources ..................................................................................17 1.5.1 Bluetooth Learning Resources.......................................................................18 1.5.2 Other Related Resources...............................................................................18 1.6 Technical Support......................................................................................................19 1.7 Documentation Conventions......................................................................................19 1.8 Acronyms ...................................................................................................................1 9 2. Software Installation 21 2.1 Before You Begin.......................................................................................................21 2.2 Install Software ..........................................................................................................21 2.3 Windows 8.1 and Windows 10 USB Selective Suspend Setting ...............................24 3. Kit Operation 25 3.1 Theory of Operation ...................................................................................................25 3.2 KitProg ..................................................................................................................... ..27 3.3 BLE Pioneer Kit USB Connection ..............................................................................27 3.4 Placing Modules on Baseboard .................................................................................28 3.5 Programming and Debugging BLE Device ................................................................29 3.5.1 Programming using PSoC Creator.................................................................29 3.5.2 Debugging using PSoC Creator.....................................................................30 3.5.3 Programming using PSoC Programmer.........................................................30 3.6 Updating BLE Dongle for CySmart Central Emulation Tool ......................................32 3.7 USB-UART Bridge .....................................................................................................34 3.8 USB-I2C Bridge .........................................................................................................35 3.9 Updating the KitProg Firmware..................................................................................36 4. Example Projects 37 4.1 Using Example Projects.............................................................................................37 4.2 CapSense Slider and LED .........................................................................................41 4.2.1 Project Description .........................................................................................41 4.2.2 Hardware Connections...................................................................................44 CY8CKIT-042-BLE-A Bluetooth® Low Energy (BLE) Pioneer Kit Guide, Doc. # 002-11468 Rev. *A 3

Contents 4.2.3 Flow Chart......................................................................................................45 4.2.4 Verify Output ..................................................................................................46 4.3 CapSense Proximity ..................................................................................................54 4.3.1 Project Description .........................................................................................54 4.3.2 Hardware Connections...................................................................................57 4.3.3 Flow Chart......................................................................................................59 4.3.4 Verify Output ..................................................................................................60 4.4 BLE Central Mode .....................................................................................................65 4.4.1 Project Description .........................................................................................65 4.4.2 Hardware Connections...................................................................................68 4.4.3 Flow Chart......................................................................................................69 4.4.4 Verify Output ..................................................................................................70 4.5 Eddystone ..................................................................................................................7 3 4.5.1 Project Description .........................................................................................73 4.5.2 Hardware Connection ....................................................................................76 4.5.3 Flow Chart......................................................................................................77 4.5.4 Verify Output ..................................................................................................77 4.6 BLE Dongle and LED Control ....................................................................................82 4.6.1 Project Description .........................................................................................82 4.6.2 Hardware Connections...................................................................................83 4.6.3 Flow Chart......................................................................................................84 4.6.4 Verify Output ..................................................................................................85 4.7 Direct Test Mode (DTM) ............................................................................................85 4.7.1 Project Description .........................................................................................85 4.7.2 Hardware Connection ....................................................................................87 4.7.3 Verify Output ..................................................................................................88 5. Hardware 89 5.1 BLE Pioneer Baseboard ............................................................................................89 5.1.1 PSoC 5LP ......................................................................................................89 5.1.2 Power System ................................................................................................89 5.1.3 Programming Interface...................................................................................96 5.1.4 Expansion Connectors ...................................................................................96 5.1.5 USB Mini-B Connector ...................................................................................99 5.1.6 CapSense Circuit .........................................................................................100 5.1.7 BLE Pioneer Baseboard LEDs.....................................................................101 5.1.8 Push-Buttons................................................................................................103 5.1.9 Cypress Ferroelectric RAM (F-RAM) ...........................................................104 5.1.10 Serial Interconnection between KitProg and Module ...................................105 5.1.11 Module Headers...........................................................................................106 5.2 Module Board ..........................................................................................................107 5.2.1 PSoC 4 BLE or PRoC BLE Device ..............................................................107 5.2.2 Module Power Connections .........................................................................108 5.2.3 Module Headers (20-Pin and 24-Pin Headers) ............................................108 5.2.4 Wiggle Antenna............................................................................................110 5.2.5 Antenna Matching Network .......................................................................... 111 5.2.6 BLE Passives ...............................................................................................112 5.2.7 Test Points....................................................................................................113 5.3 BLE Dongle Board ...................................................................................................113 5.3.1 Power System ..............................................................................................114 5.3.2 USB Type-A Plug .........................................................................................114 5.3.3 User LED......................................................................................................115 CY8CKIT-042-BLE-A Bluetooth® Low Energy (BLE) Pioneer Kit Guide, Doc. # 002-11468 Rev. *A 4

Contents 6. Advanced Topics 116 6.1 Using FM24V10 F-RAM...........................................................................................116 6.1.1 Address Selection ........................................................................................116 6.1.2 Write/Read Operation ..................................................................................117 A. Appendix 118 A.1 Bill of Materials (BOM) .............................................................................................118 A.2 KitProg Status LED States.......................................................................................127 A.3 Adding BLE Module-Compatible Headers on Your Baseboard ...............................128 A.4 Programming BLE Modules via MiniProg3 ..............................................................129 A.5 BLE Modules and BLE Dongles Compatible with the BLE Pioneer Kit ...................130 A.6 Migrating Projects Across Different Pioneer Series Kits ..........................................136 Revision History 142 CY8CKIT-042-BLE-A Bluetooth® Low Energy (BLE) Pioneer Kit Guide, Doc. # 002-11468 Rev. *A 5

Safety Information The CY8CKIT-042-BLE-A Bluetooth® Low Energy (BLE) Pioneer Kit is intended for development purposes only. Users are advised to test and evaluate this kit in an RF development environment. This kit is not a finished product and when assembled may not be resold or otherwise marketed unless all required authorizations are first obtained. Contact support@cypress.com for details. CY8CKIT-042-BLE-A boards contain ESD-sensitive devices. Electrostatic charges readily accumulate on the human body and any equipment, and can discharge without detection. Permanent damage may occur on devices subjected to high-energy discharges. Proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Store unused CY8CKIT-042-BLE-A boards in the protective shipping package. End-of-Life/Product Recycling The end-of-life cycle for this kit is five years from the date of manufacture mentioned on the back of the box. Contact your nearest recycler to discard the kit. General Safety Instructions ESD Protection ESD can damage boards and associated components. Cypress recommends that the user perform procedures only at an ESD workstation. If an ESD workstation is not available, use appropriate ESD protection by wearing an antistatic wrist strap attached to the chassis ground (any unpainted metal surface) on the board when handling parts. Handling Boards CY8CKIT-042-BLE-A boards are sensitive to ESD. Hold the board only by its edges. After removing the board from its box, place it on a grounded, static-free surface. Use a conductive foam pad if available. Do not slide the board over any surface. CY8CKIT-042-BLE-A Bluetooth® Low Energy (BLE) Pioneer Kit Guide, Doc. # 002-11468 Rev. *A 6

Battery Care and Use Use the correct size and type of battery specified in this guide. Keep battery contact surfaces and battery compartment contacts clean by rubbing them with a clean pencil eraser or a rough cloth each time you replace batteries. Remove the battery from a device when it is not expected to be in use for several months. Make sure that you insert the battery into your device properly, with the + (plus) and – (minus) terminals aligned correctly. Do not place the battery next to metallic objects such as keys and coins. Never throw the battery into fire. Do not open up the battery. Do not short the battery. Do not subject the battery to high temperatures or high humidity. Store the battery in a dry place. Do not recharge a battery unless it is marked “rechargeable.” Battery Disposal Batteries can be safely disposed with normal household waste. Never dispose batteries in fire because they can explode. It is important not to dispose large amounts of batteries in a group. Used batteries are often not completely “dead.” Grouping used batteries together can bring these “live” batteries into contact with one another, creating safety risks. CY8CKIT-042-BLE-A Bluetooth® Low Energy (BLE) Pioneer Kit Guide, Doc. # 002-11468 Rev. *A 7

_ SS¥Crpares Embedded in fomarro Regulatory Compliance Information The CY8CKIT—042—BLE—A kit contains devices that transmit and receive radio signals in accordance with the spectrum regulations for the 2.4—GHz unlicensed frequency range. Cypress Semiconductor Corporation has obtained regulatory approvals for this kit to be used in specific countries. These countries include the United States (FCC Part 15), Canada (IC RSS210), and Japan (JRF/TELEC). Additional regional regulatory agency approval may be required to operate these throughout the world. This kit, as shipped from the factory, has been tested and found to comply with the limits and requirements for the following compliances: m As a Class B digital device, pursuant to part 15 of the FCC Rules. m As a Class B digital apparatus, compliant with Canadian ICES—003. Regulatory Statements and Product Labeling United States (FCC) The CY8CKIT—143A PSoC 4 BLE, CY5676A PRoC BLE and CY5677 PRoC BLE transmitter complies with Part 15 of the Federal Communications Commission (FCC) Rules. The FCC ID for these devices are WAP—CY5677 for CY5677 and WAP—CY5676A for CY8CKIT—143A and CY5676A. Operation is subject to the following two conditions: m This device may not cause harmful interference m This device must accept any interference received, including interference that may cause unde— sired operation. CY8CKIT—042—BLE—A Bluetooth® Low Energy (BLE) Pioneer Kit Guide, Doc. # 002—11468 Rev. *A 8

Uncontrolled environment.

1. Introduction Thank you for your interest in the CY8CKIT-042-BLE-A Bluetooth® Low Energy (BLE) Pioneer Kit. The BLE Pioneer Kit enables customers to evaluate and develop BLE projects using the PSoC® 4 BLE and PRoC™ BLE (Programmable Radio-on-Chip) devices. Bluetooth SMART™ or Bluetooth Low Energy (BLE) is a full-featured, layered, communication protocol that includes a 2.4-GHz radio, a link layer, and an application layer. However, you do not need to understand the complex protocol to implement your projects using PSoC 4 BLE or PRoC BLE. The Cypress BLE solution, which includes the device, the BLE Component, and the BLE firmware stack will take care of it for you. The Cypress BLE firmware stack is royalty free. You will use two software tools, PSoC Creator™ and CySmart™ Central Emulation Tool, to develop and debug your BLE project. PSoC Creator is Cypress’ standard integrated design environment (IDE). The BLE protocol has been abstracted into an easy drag-and-drop BLE Component in PSoC Creator. The CySmart Central Emulation Tool is a host tool for Windows PCs, which provides an easy-to-use GUI to enable customers to test and debug their BLE projects. The BLE Pioneer Kit offers footprint-compatibility with Arduino™ shields as well as 6-pin Digilent® Pmod™ daughter cards. In addition, the kit features a CapSense® slider, an RGB LED, a push- button switch, an onboard programmer/debugger and the USB-UART/I2C bridge functionality block (KitProg), a coin cell battery holder, and a Cypress F-RAM™. The BLE Pioneer Kit supports 1.9 V, 3 V, 3.3 V, or 5 V as operating voltages. The BLE Pioneer Kit supports two devices: PSoC 4 BLE is a 32-bit, 48-MHz ARM® Cortex®-M0 BLE solution with CapSense, 12-bit analog front end (1x SAR ADC, 4x low-power opamps, 2x low-power comparators, and 2x current DACs), 4x TCPWM1, 2x SCBs2, 4x UDBs3, LCD4, I2S5, and 36 GPIOs. PSoC 4 BLE provides a complete solution for sports and fitness monitors, wearable electronics, medical devices, home automation systems, and sensor-based low-power systems for the Internet of Things (IoT). PRoC BLE is a 32-bit, 48-MHz ARM Cortex-M0 BLE solution with CapSense, 12-bit ADC, 4x TCPWM1, 2x SCBs2, LCD4, I 2S5, and 36 GPIOs. PRoC BLE provides a complete solution for BLE connectivity, HID, remote controls, and toys. Two different versions of the BLE Pioneer Kit are currently available. These kits differ in the BLE modules and the dongle that are included. The baseboard in both kits are identical, so any BLE module can be used interchangeably with either baseboard. Table 1-1 lists the modules and dongle included in each kit. Table 1-1. Default BLE Modules and BLE Dongle in the Two BLE Pioneer Kits Kit PSoC Module PRoC Module Dongle Flash Size Bluetooth Version CY8CKIT-042-BLE CY8CKIT-142 CY5671 CY5670 128 KB 4.1 CY8CKIT-042-BLE-A CY8CKIT-143A CY5676A CY5677 256 KB 4.1 and 4.2 1. Configurable timer, counter, and pulse-width modulator. 2. Serial communication blocks (configurable to I2C, SPI, or UART). 3. Universal digital blocks 4. Configurable liquid crystal display driver. 5. Configurable integrated interchip sound serial bus interface. CY8CKIT-042-BLE-A Bluetooth® Low Energy (BLE) Pioneer Kit Guide, Doc. # 002-11468 Rev. *A 10

Introduction 1.1 Kit Contents The BLE Pioneer Kit contains the following items (see Figure 1-1): BLE Pioneer Baseboard preloaded with the CY8CKIT-143A PSoC 4 BLE 256KB Module CY5676A PRoC BLE 256KB Module CY5677 CySmart BLE 4.2 USB Dongle (BLE Dongle) Quick start guide USB Standard-A to Mini-B cable Four jumper wires (4 inch) and two proximity sensor wires (5 inch) Coin cell (3-V CR2032) Figure 1-1. Kit Contents If any part of the BLE Pioneer Kit is missing, contact your nearest Cypress sales office for help: www.cypress.com/go/support. CY8CKIT-042-BLE-A Bluetooth® Low Energy (BLE) Pioneer Kit Guide, Doc. # 002-11468 Rev. *A 11

Introduction 1.2 BLE Pioneer Baseboard Details The BLE Pioneer Baseboard consists of the blocks shown in Figure 1-2. 1. RGB LED 2. BLE device reset button 3. CapSense proximity header 4. User button 5. CapSense slider 6. Arduino-compatible I/O headers (J2/J3/J4) 7. Arduino-compatible power header (J1) 8. Digilent Pmod-compatible I/O header (J5) 9. Cypress F-RAM 1 Mb (FM24V10-G) 10.PSoC 5LP I/O header (J8) 11. PSoC 5LP programmer and debugger (CY8C5868LTI-LP039) 12.Coin cell holder (bottom side) 13.USB connector (J13) 14.Power LED and Status LED 15.System power supply jumper (J16) - LDO 1.9 V~5 V 16.BLE power supply jumper / current measurement (J15) 17.BLE module headers (J10/J11) Figure 1-2. BLE Pioneer Baseboard CY8CKIT-042-BLE-A Bluetooth® Low Energy (BLE) Pioneer Kit Guide, Doc. # 002-11468 Rev. *A 12

Introduction Figure 1-3 shows a markup of the onboard components of the PSoC 4 BLE module (in red) and the PRoC BLE module (in black). See BLE Modules and BLE Dongles Compatible with the BLE Pioneer Kit on page 130 for more details. Figure 1-4 shows the BLE Dongle board blocks. Figure 1-3. BLE Module Markup 32.768-kHz crystal 32.768-kHz crystal Figure 1-4. BLE Dongle Markup CY8CKIT-042-BLE-A Bluetooth® Low Energy (BLE) Pioneer Kit Guide, Doc. # 002-11468 Rev. *A 13

Introduction 1.3 PSoC Creator PSoC Creator™ is a state-of-the-art, easy-to-use integrated design environment (IDE). It introduces revolutionary hardware and software co-design, powered by a library of pre-verified and pre- characterized PSoC Components. With PSoC Creator, you can: 1. Drag and drop Components to build your hardware system design in the main design workspace 2. Codesign your application firmware with the PSoC hardware 3. Configure Components using configuration tools 4. Explore the library of 100+ Components 5. Review Component datasheets Figure 1-5. PSoC Creator Features PSoC Creator also enables you to tap into an entire tool ecosystem with integrated compiler chains and production programming programmers for PSoC devices. For more information, visit www.cypress.com/psoccreator. Visit PSoC Creator training page for video tutorials on learning and using PSoC Creator. CY8CKIT-042-BLE-A Bluetooth® Low Energy (BLE) Pioneer Kit Guide, Doc. # 002-11468 Rev. *A 14

Introduction 1.3.1 PSoC Creator Code Examples PSoC Creator includes a large number of code examples. These examples are available from the PSoC Creator Start Page, as Figure 1-6 shows. Code examples can speed up your design process by starting you off with a complete design, instead of a blank page. The code examples also show how PSoC Creator Components can be used for various applications. Code examples and documentation are included, as shown in Figure 1-7 on page 17. In the Find Example Project dialog shown in Figure 1-7, you have several options: Filter for examples based on architecture or device family, that is, PSoC 3, PSoC 4 or PSoC 5LP; project name; or keyword. Select from the menu of examples offered based on the Filter Options. Review the example project’s description (on the Documentation tab). Review the code from the Sample Code tab. You can copy the code from this window and paste to your project, which can help speed up code development. Create a new project (and a new workspace if needed) based on the selection. This can speed up your design process by starting you off with a complete, basic design. You can then adapt that design to your application. Figure 1-6. Code Examples in PSoC Creator CY8CKIT-042-BLE-A Bluetooth® Low Energy (BLE) Pioneer Kit Guide, Doc. # 002-11468 Rev. *A 15

Introduction Figure 1-7. Code Example Projects with Sample Code 1.3.2 Kit Code Examples This kit includes a number of code examples, which can be used to quickly evaluate the functionality of this kit. These examples are described in the Example Projects chapter on page 37. If you are a beginner in BLE, refer to the PSoC Creator code examples such as BLE_FindMe and BLE_Device_Information_Service as described in 1.3.1 PSoC Creator Code Examples. You may also refer the application note Getting Started with PSoC 4 BLE. The four Kit code examples viz CapSense Slider and LED, CapSense Proximity, BLE Central Mode and Eddystone are intermediatory level examples that will help to design a system around the kit. Refer to the 4.2 CapSense Slider and LED and later for details. The CySmart Dongle code example is an advanced level example that will demonstrate a complete solution around the kit. Refer to 4.6 BLE Dongle and LED Control for details. 1.3.3 PSoC Creator Help Visit the PSoC Creator home page to download the latest version of PSoC Creator. Then, launch PSoC Creator and navigate to the following items: Quick Start Guide: Choose Help > Documentation > Quick Start Guide. This guide gives you the basics for developing PSoC Creator projects. Simple Component example projects: Choose File > Code Example. These example projects demonstrate how to configure and use PSoC Creator Components. System Reference Guide: Choose Help > System Reference Guide. This guide lists and describes the system functions provided by PSoC Creator. CY8CKIT-042-BLE-A Bluetooth® Low Energy (BLE) Pioneer Kit Guide, Doc. # 002-11468 Rev. *A 16

Introduction Component datasheets: Right-click a Component and select Open Datasheet, as shown in Figure 1-8 on page 18. Visit the PSoC 4 Component Datasheets page for a list of all PSoC 4 Component datasheets. Document Manager: PSoC Creator provides a document manager to help you to easily find and review document resources. To open the document manager, choose the menu item Help > Document Manager. 1.3.4 Component Datasheets Right-click a Component and select Open Datasheet (see Figure 1-8 on page 18). Figure 1-8. Opening Component Datasheet 1.4 Getting Started This guide will help you get acquainted with the BLE Pioneer Kit: The Software Installation chapter on page 21 describes the installation of the kit software. This includes the PSoC Creator IDE for development and debugging applications, PSoC Programmer for programming hex files, and the CySmart Central Emulation Tool for BLE Central emulation. The Kit Operation chapter on page 25 describes the major features of the BLE Pioneer Kit such as USB-UART and USB-I2C bridges and functionalities such as programming and debugging. The Example Projects chapter on page 37 describes multiple PSoC 4 BLE and PRoC BLE code examples that will help you understand how to create your own BLE application using the BLE Component and device. The Hardware chapter on page 89 details the hardware content of the BLE Pioneer Kit and BLE Dongle, and the hardware operation. The Advanced Topics chapter on page 116 explains the functionality of FM24V10 F-RAM. The Appendix on page 118 provides the bill of materials (BOM), KitProg LED states, list of BLE modules and dongles compatible with the BLE Pioneer Kit, migrating projects across Pioneer series kits, and programming BLE modules using MiniProg3. 1.5 Additional Learning Resources Cypress provides a wealth of information at www.cypress.com to help you to select the right PSoC device for your design, and to help you to quickly and effectively integrate the device into your design. For a comprehensive list of resources, see KBA86521, How to Design with PSoC 3, PSoC 4, and PSoC 5LP. Visit www.cypress.com/go/psoc4ble and www.cypress.com/procble for additional learning resources including datasheets, technical reference manuals, and application notes.The following is an abbre- viated list: Overview: PSoC 4 BLE Portfolio and PSoC Roadmap Product Selectors: PSoC 1, PSoC 3, PSoC 4, or PSoC 5LP. In addition, PSoC Creator includes a device selection tool. CY8CKIT-042-BLE-A Bluetooth® Low Energy (BLE) Pioneer Kit Guide, Doc. # 002-11468 Rev. *A 17

Introduction Datasheets: Describe and provide electrical specifications for the PSoC 4 device family CapSense Design Guide: Learn how to design capacitive touch-sensing applications with the PSoC 4 family of devices. Application Notes and Code Examples: Cover a broad range of topics, from basic to advanced level. Many of the application notes include code examples. Visit the PSoC 3/4/5 Code Examples webpage for a list of all available PSoC Creator code examples. To access code examples from within PSoC Creator, see PSoC Creator Code Examples on page 16. Technical Reference Manuals (TRM): Provide detailed descriptions of the architecture and registers in each PSoC 4 device family. Development Kits: CY8CKIT-040, CY8CKIT-042, and CY8CKIT-044 are easy-to-use and inexpensive develop- ment platforms. These kits include connectors for Arduino-compatible shields and Digilent Pmod peripheral modules. CY8CKIT-141, CY8CKIT-142, CY8CKIT-143, CY5671, CY5674, and CY5676 are additional BLE Modules compatible with the BLE Pioneer Kit. CY5670 is additional BLE Dongle compatible with the BLE Pioneer Kit. CY8CKIT-049 is a very low-cost prototyping platform for PSoC 4100/4200 families. The MiniProg3 kit provides an interface for flash programming and debug. CY5672 PRoC BLE Remote Control Reference Design Kit provides a production-ready imple- mentation of a Bluetooth Low Energy remote control. CY5682 PRoC BLE Touch Mouse Reference Design Kit provides a production-ready imple- mentation of a Bluetooth Low Energy touch mouse. Knowledge Base Articles (KBA): Provide design and application tips from experts on using the device. PSoC Creator Training: Visit www.cypress.com/go/creatorstart/creatortraining for a comprehensive list of video trainings on PSoC Creator. Cysmart Central Emulation Tool: Visit www.cypress.com/go/cysmart for information on the CySmart Central Emulation Tool. Learning From Peers: Visit www.cypress.com/forums to meet enthusiastic PSoC developers discussing the next generation embedded systems on Cypress Developer Community Forums. 1.5.1 Bluetooth Learning Resources The Bluetooth Developer Portal provides material by the Special Interest Group (SIG) for learning various aspects of the Bluetooth Low Energy protocol and systems. Some of them are: Training videos GATT profiles Bluetooth community forum 1.5.2 Other Related Resources Digilent Pmod: www.digilentinc.com/pmods/ Arduino: http://arduino.cc/en/Main/ArduinoBoardUno CY8CKIT-042-BLE-A Bluetooth® Low Energy (BLE) Pioneer Kit Guide, Doc. # 002-11468 Rev. *A 18

Introduction 1.6 Technical Support If you have any questions, our technical support team is happy to assist you. You can create a support request on the Cypress Technical Support page. If you are in the United States, you can talk to our technical support team by calling our toll-free number: +1-800-541-4736. Select option 2 at the prompt. You can also use the following support resources if you need quick assistance. Self-help. Local Sales Office Locations. 1.7 Documentation Conventions Table 1-2. Document Conventions for Guides Convention Usage Displays file locations, user entered text, and source code: Courier New C:\...cd\icc\ Displays file names and reference documentation: Italics Read about the sourcefile.hex file in the PSoC Creator User Guide. Displays keyboard commands in procedures: [Bracketed, Bold] [Enter] or [Ctrl] [C] Represents menu paths: File > Open File > Open > New Project Displays commands, menu paths, and icon names in procedures: Bold Click the File icon and then click Open. Displays an equation: Times New Roman 2+2=4 Text in gray boxes Describes cautions or unique functionality of the product. 1.8 Acronyms Table 1-3. Acronyms Used in this Document Acronym Definition ADC analog-to-digital converter API application programming interface BD address Bluetooth device address BLE Bluetooth Low Energy CDC Communications Device Class COM communication port DLE data length extension ECDH Elliptic Curve Diffie-Hellman DVD digital video disc ESD electrostatic discharge F-RAM ferroelectric random access memory GATT generic attribute profile CY8CKIT-042-BLE-A Bluetooth® Low Energy (BLE) Pioneer Kit Guide, Doc. # 002-11468 Rev. *A 19

Introduction Table 1-3. Acronyms Used in this Document Acronym Definition GUI graphical user interface GPIO general-purpose input/output I2C inter-integrated circuit IAS immediate alert service IDAC current output digital-to-analog converter IDE integrated development environment LDO low drop out (voltage regulator) LE low energy LED light-emitting diode LP low power LPT line print terminal MTU maximum transmission unit OTA over-the-air PHY physical layer PrISM Precise Illumination Signal Modulation PRoC Programmable Radio-on-Chip PSM protocol service multiplexer PSoC Programmable System-on-Chip PWM pulse width modulation QFN quad flat no-lead (package) RDK reference design kit RGB red green blue SAR successive approximation register SIG special interest group SMA SubMiniature version A SPI serial peripheral interface SWD serial wire debug TLM telemetry UART universal asynchronous receiver transmitter UID universal identifier URI uniform resource identifier URL uniform resource locator USB Universal Serial Bus UUID universal unique identifier CY8CKIT-042-BLE-A Bluetooth® Low Energy (BLE) Pioneer Kit Guide, Doc. # 002-11468 Rev. *A 20

<~—~ SSzCrpnrss ieirorer Cavurmmvreweern enimiuvine sum cnergy weny i nuser ns awe, veveruuetrruy new m

2. Software Installation This chapter describes the steps to install the software tools and packages on a computer for using the BLE Pioneer Kit. This includes the IDE in which the projects will be built and used for program- ming. 2.1 Before You Begin All Cypress software installations require administrator privileges. Ensure you have the required privileges on the system for successful installation. Before you install the kit software, close any other Cypress software that is currently running. 2.2 Install Software Follow these steps to install the BLE Pioneer Kit software: 1. Download the kit software from www.cypress.com/CY8CKIT-042-BLE-A. The software is available in the following formats: a. CY8CKIT-042-BLE-A Kit Complete Setup: This installation package contains the files related to the BLE Pioneer Kit. However, it does not include the Windows Installer or Microsoft .NET framework packages. If these packages are not on your computer, the installer directs you to download and install them from the Internet. b. CY8CKIT-042-BLE-A Kit Only Package: This executable file installs only the BLE Pioneer Kit contents, which include code examples, hardware files, and user documents. This package can be used if all the software prerequisites (listed in step 5) are installed on your computer. c. CY8CKIT-042-BLE-A DVD ISO: This file is a complete package, stored in a DVD-ROM image format, that you can use to create a DVD or extract using an ISO extraction program such as WinZip or WinRAR. The file can also be mounted similar to a virtual CD/DVD using virtual drive programs such as ‘Virtual CloneDrive’ and ‘MagicISO’. This file includes all the required software, utilities, drivers, hardware files, and user documents. 2. If you have downloaded the ISO file, mount it on a virtual drive; if you do not have a virtual drive to mount, extract the ISO contents using the appropriate ISO extractor (such as MagicISO or PowerISO). Double-click cyautorun.exe in the root directory of the extracted content or mounted ISO if “Autorun from CD/DVD” is not enabled on the computer. The installation window will appear automatically. Note: If you are using the “Kit Complete Setup” or “Kit Only Package” file, then go to step 4 for installation. CY8CKIT-042-BLE-A Bluetooth® Low Energy (BLE) Pioneer Kit Guide, Doc. # 002-11468 Rev. *A 21

Software Installation 3. Click Install CY8CKIT-042-BLE-A Kit to start the installation, as shown in Figure 2-1. Figure 2-1. Installer Screen 4. Select the folder in which you want to install the CY8CKIT-042-BLE-A kit-related files. Choose the directory and click Next. 5. When you click Next, the CY8CKIT-042-BLE-A Kit installer automatically installs the required software, if it is not present on your computer. The following software packages are required: Note: For the Kit Only Package, download and install the following prerequisites. a. PSoC Creator 3.3 or later: Download the latest version from www.cypress.com/psoccreator. b. PSoC Programmer 3.24 or later: This is installed as part of PSoC Creator installation (www.cypress.com/programmer). c. CySmart 1.2 or later: Download the latest version from www.cypress.com/cysmart. CY8CKIT-042-BLE-A Bluetooth® Low Energy (BLE) Pioneer Kit Guide, Doc. # 002-11468 Rev. *A 22

Software Installation 6. Choose the Typical/Custom/Complete installation type in the Product Installation Overview window, as shown in Figure 2-2. Click Next after you select the installation type. Figure 2-2. Product Installation Overview 7. Read the license agreement and select I accept the terms in the license agreement to continue with installation. Click Next. 8. When the installation begins, a list of packages appears on the installation page. A green check mark appears next to each package after successful installation. 9. Click Finish to complete the CY8CKIT-042-BLE-A kit installation. 10.Enter your contact information or select the Continue Without Contact Information check box. Click Finish to complete the CY8CKIT-042-BLE-A kit installation. 11. After the installation is complete, the kit contents are available at the following location: <Install_Directory>\CY8CKIT-042-BLE-A Kit Default location: Windows 7 (64-bit): C:\Program Files (x86)\Cypress\CY8CKIT-042-BLE-A Kit Windows 7 (32-bit): C:\Program Files\Cypress\CY8CKIT-042-BLE-A Kit Note: For Windows 7/8/8.1 users, the installed files and the folder are read only. To use the installer example projects, follow the steps outlined in the Example Projects chapter on page 37. The BLE Pioneer Kit installer also installs the CySmart Central Emulation Tool on your computer. This software, along with the BLE Dongle, allows the computer to emulate as a BLE Central device. CY8CKIT-042-BLE-A Bluetooth® Low Energy (BLE) Pioneer Kit Guide, Doc. # 002-11468 Rev. *A 23

Software Installation 2.3 Windows 8.1 and Windows 10 USB Selective Suspend Setting The Windows 8.1 and Windows 10 operating sy stems issue a suspend command to a connected USB device if there is no activity on its USB bus. This may happen to the BLE Pioneer Kit/BLE Don- gle if the driver installation is not complete or the driver is not found. In this situation, as a response to the suspend command from the operating system, the KitProg will shut down the onboard LDO to remain within the USB suspend current requirement. Due to this, the BLE Pioneer Kit will not be powered and will not be functional. To prevent this, do either of the following: Install the kit software on the Windows 8.1 or Windows 10 operating system before using the BLE Pioneer Kit. Disable the USB selective suspend setting for the BLE Pioneer Kit from Power Options on Win- dows 8.1, by following these steps: a. From Control Panel, go to Power Options. b. Click Change Plan Settings corresponding to your power plan. c. Click Change Advanced Power Settings. d. Under Advanced settings, expand USB Settings > USB selective suspend setting. e. Select the Disabled option for Plugged in and On battery operation. f. Click OK. CY8CKIT-042-BLE-A Bluetooth® Low Energy (BLE) Pioneer Kit Guide, Doc. # 002-11468 Rev. *A 24


Document Created: 2016-06-29 22:15:55
Document Modified: 2016-06-29 22:15:55
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC