User Manual

FCC ID: W9Z-ARANETTC

Users Manual

Download: PDF
FCCID_4449158

Τ COMPACT SENSOR Aranet T Compact sensor - business critical real-time temperature readings for supermarkets and cold storage with a small form factor and food grade casing. Aranet T Compact sensor Datasheet Measurements Temperature Line of Sight Range 3km / 1.9mi Operating environment Indoor and Outdoor use Transmitter power 14 dBm Frequency Depends on base station instructions Measurement Range -40°C to 60°C (-40°F to 140 °F) Measurement accuracy -10°C to 60°C / 14°F to 140°F 0.4°C / 0.7°F -40°C to -10°C / -40°F to 14°F 0.5°C / 0.9°F Response time τ63% - 8 minutes at 1 m/s airflow Data Transmission 1, 2, 5, 10 minutes* Data Protection Data encryption Power options 1 AAA Alkaline battery (Zn/Mn02) 1 AAA Lithium battery (Li/FeS2) Battery life @20°C / 68°F Up to 5 years with Alkaline battery Up to 7 years with Lithium battery Operating temperature -20°C to 55°C/ -4°F to 131°F with Alkaline battery -40°C to 60°C/ -40°F to 140°F with Lithium battery Operating humidity 0% to 100% Dimensions 30mmØx77mm/ 1.2”Øx3” Weight 30g (1.05oz) with Alkaline battery 28g (1oz) with Lithium battery Construction ASA Plastic Protection class IP68 Marking CE, FCC Compatible base stations Aranet PRO and Aranet MINI Included 1 AAA Alkaline battery, string Part number TDSPT004 (EU) Mounting bracket part number TDAPMB01 (EU) * 1, 2, 5, 10 min interval supported from Aranet PRO v1.3.2 and Aranet MINI v3.20.

FCC Compliance statement The information presented in this guide is the property of SAF Tehnika, JSC. No part of this document may be reproduced or This equipment has been tested and found to comply with the limits transmitted without proper permission from SAF Tehnika, JSC. for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against The specifications or information contained in this document are harmful interference in a residential installation. This equipment subject to change without notice due to continuing introduction of generates, uses and can radiate radio frequency energy and, if design improvements. If there is any conflict between this document not installed and used in accordance with the instructions, may and compliance statements, the latter will supersede this document. cause harmful interference to radio communications. However, SAF Tehnika, JSC has no liability for typing errors in this document or there is no guarantee that interference will not occur in a particular damages of any kind that result from the use of this document. installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the To get up to date information about accessories and their availability, equipment off and on, the user is encouraged to try to correct the please contact sales representative. interference by one or more of the following measures: Copyright Notice TT Reorient or relocate the receiving antenna. Copyright © 2019 SAF Tehnika, JSC. All rights reserved. TT Increase the separation between the equipment and receiver. Industry Canada Regulatory Statement TT Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device TT Consult the dealer or an experienced radio/TV technician for help. may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired Changes or modifications not expressly approved operation of the device. by the party responsible for compliance could void the user’s authority to operate the equipment. RF Exposure Statement: 20cm minimum distance between the radiator and human body. RF Exposure Statement: 20cm minimum distance between the Le présent appareil est conforme aux CNR d’Industrie Canada radiator and human body. applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas This device complies with part 15 of the FCC Rules. Operation is produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter subject to the following two conditions: (1) This device may not tout brouillage radioélectrique subi, même si le brouillage est cause harmful interference, and (2) this device must accept any susceptible d’en compromettre le fonctionnement. interference received, including interference that may cause Déclaration d’exposition FR: distance minimale de 20 cm entre le undesired operation. radiateur et le corps humain. How to: Pair sensors to Aranet short flash. Looking at the LED light can save time while pairing sensors, however, Aranet PRO will also display a notification about a successful or unsuccessful pairing. (8) Close the sensor following respective sensor instructions. (9) Now you can rename the sensor, set thresholds for alarms, add it to favorites. After completing your tasks 1. Pair sensors with Aranet PRO click save button. Aranet PRO supports several types of sensors. In order to connect them to the system the same steps apply for all 2. Pair sensors with Aranet MINI types of sensors. (1) Tap , then choose Sensors menu and tap the Setup (1) You should physically be located within around 20 meters button. of Aranet PRO. (2) Set up a sensor by following the instructions on the (2) In order to open the sensor follow the individual sensor’s screen. After successfully setting up a sensor, the sensor instructions (see image above). Once it is opened the ID and the name of the sensor will appear on the left side battery compartment will be exposed. of the screen. Sensors are given name “SENS <number>” automatically. Tap the name of the sensor to give it a new (3) Go to Aranet PRO Settings screen. name with length up to 8 symbols. In order to remove a (4) Choose “Sensors” menu. sensor just press the sign next to it. (5) Click “Add sensor” button. (3) Set up other sensors in the same manner. (6) Insert sensor’s battery/-ies. TT To add more than 6 sensors, press the page button on top. (7) Red LED light will flash on the sensor. Three short flashes TT To change the order of the sensors, press and . Then press on followed by a long flash will signal a connection failure, the the sensors you want to move and then – where you want to pause between flashes will be the same. In a successful move it to. pairing the long flash will follow immeadiately after a TT Tap the home button to return to the main menu. For more detailed information about Aranet products, please visit www.aranet.com, contact us info@aranet.com or your Aranet representative. Product specifications are subject to change without prior notice. SAF Tehnika © 2019


Document Created: 2019-09-17 12:49:32
Document Modified: 2019-09-17 12:49:32
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC