User Manual

FCC ID: W9Z-ARANET4

Users Manual

Download: PDF
FCCID_4420171

ARANET4 Aranet4 Datasheet Measurements CO2 (carbon dioxide), temperature, relative humidity, atmospheric pressure Line of Sight Range Aranet radio up to 3 km/ 1.9mi BLE up to 10m/33ft Operating environment Indoor use Transmitter power 14 dBm Frequency Depends on base station instructions Measurement range CO2 0-9999 ppm temperature 0°C to 60°C (14°F to 140°F)* relative humidity 0% to 85% RH atmospheric pressure 300-1100 hPa Measurement accuracy:** CO2 0-2000 ppm: ±50 ppm or 3% of reading 2001-9999 ppm: ±10% of reading temperature ±0.4°C (0.72°F) relative humidity ±3% atmospheric pressure ±1 hPa CO2 measurement calibration Automatic or manual (at 400ppm) Data Transmission 1, 2, 5, 10 minutes Data Protection Data encryption Power options 2 AA Alkaline batteries (Zn/Mn02) Battery life @20°C / 68°F Up to 2 years Operating temperature 0°C to 50°C (32°F to 122°F) Operating humidity 0% to 85% non-condensing Dimensions 70 x 70 x 24 mm / 2.716” x 2.76” x 0.94” Weight 104g (3.7oz) Construction Polycarbonate Protection class IP20 Marking CE Compatible base stations Aranet PRO (from v1.3.2) Included 2 AA Alkaline batteries Part number TDSPC003(EU) * Please note the operating temperature range. ** For best accuracy, recommended operating range is 10°C to 40°C (50°F to 104°F) and 20% to 60% RH (non-condensing). Prolonged operation beyond these ranges may result in a shift of sensor reading, with slow recovery time.

FCC Compliance statement The information presented in this guide is the property of SAF Tehnika, JSC. No part of this document may be reproduced or This equipment has been tested and found to comply with transmitted without proper permission from SAF Tehnika, JSC. the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide The specifications or information contained in this document are reasonable protection against harmful interference in a subject to change without notice due to continuing introduction residential installation. This equipment generates, uses and of design improvements. If there is any conflict between this can radiate radio frequency energy and, if not installed and document and compliance statements, the latter will supersede used in accordance with the instructions, may cause harmful this document. interference to radio communications. However, there is SAF Tehnika, JSC has no liability for typing errors in this no guarantee that interference will not occur in a particular document or damages of any kind that result from the use of this installation. If this equipment does cause harmful interference document. to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to To get up to date information about accessories and their try to correct the interference by one or more of the following availability, please contact sales representative. measures: Copyright Notice TT Reorient or relocate the receiving antenna. Copyright © 2019 SAF Tehnika, JSC. All rights reserved. TT Increase the separation between the equipment and receiver. Industry Canada Regulatory Statement TT Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) TT Consult the dealer or an experienced radio/TV technician for help. This device may not cause interference; and (2) This device must accept any interference, including interference that may cause Changes or modifications not expressly undesired operation of the device. approved by the party responsible for compliance could void the user’s authority to Le présent appareil est conforme aux CNR d’Industrie Canada operate the equipment. applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne This device complies with part 15 of the FCC Rules. Operation is doit pas produire de brouillage, et (2) l’utilisateur de l’appareil subject to the following two conditions: (1) This device may not doit accepter tout brouillage radioélectrique subi, même si le cause harmful interference, and (2) this device must accept any brouillage est susceptible d’en compromettre le fonctionnement. interference received, including interference that may cause undesired operation.

What is the Aranet4 device? 6. Bluetooth status. If the Bluetooth symbol is visible, then Bluetooth connectivity function is enabled. Refer to switch The Aranet4 sensor is a battery powered CO2 meter with positions of the Aranet4 in chapter Switch positions explained. additional measurements of temperature, relative humidity and Make sure Bluetooth connectivity is enabled on your smart atmospheric pressure*. The device is suitable for monitoring device if you would like to connect to the Aranet4 device. the CO2 level in your school, office or home environment. 7. The Aranet radio status. If the Aranet radio symbol is visible, Measurement data are displayed on power efficient e-ink then the radio connectivity with Aranet PRO base station is screen allowing for long battery life. Additionally the device can enabled. Refer to switch positions of the Aranet4 in chapter provide a visual and sound notifications in case the CO2 level Switch positions explained. has exceeded high concentration level above 1400 ppm (level 8. CO2 indication mode. If the leaf symbol is visible, then CO2 associated typically with complaints of drowsiness and poor air level indication is set to plant mode (plants require higher quality). CO2 level than humans). If the leaf symbol is not visible, then CO2 level indication is set to human mode. Selection of the mode can be done using the Aranet4 app. 9. CO2 threshold level indication. In case the CO2 indication human mode is selected: • Green represents normal level (below 1000 ppm), Uses the nondispersive infrared (NDIR) sensor to measure CO2. The CO2 gas in the chamber absorbs infrared light and this • Yellow represents average level (1000 to 1400 ppm), absorption is measured by the sensor. The less light passes • Red represents high level (above 1400 ppm). through - the higher the CO2 level. The CO2 gas absorbs only a specific wavelength of the light, thus an optical filter is needed. In case the plant mode is selected: Using the Aranet4 app on your smart devices it is possible to • Green represents normal level (above 500 ppm), wirelessly access the current and up to one week historical • Yellow represents average level (500 to 300 ppm), measurement data and adjust the configuration of the Aranet4 device. The Aranet4 app allows connecting several Aranet4 • Red represents high level (below 300 ppm). sensors to monitor their parameters remotely from one smart 10. CO2 calibration mode indication. Symbol “A” is displayed device. when calibration is set to automatic. No letter is displayed Additionally, up to 100 Aranet4 devices can be connected to the when calibration is set to manual mode. Refer to switch Aranet PRO base station. Refer to chapter Using Aranet4 device positions of the Aranet4 in chapter Switch positions with the Aranet PRO base station. explained. *Atmospheric pressure data are available only on the Aranet app. Switch positions explained The Aranet4 sensor screen explained 2 3 4 10 5 AUTO °C 1 MANUAL °F 0 0 6 9 8 7 1. CO2 concentration level in ppm (parts per million) 2. Temperature of the air in Celsius or Fahrenheit. Refer to the The Aranet4 device has switches that allow the user to adjust switch positions of the Aranet4 in chapter Switch positions the preferences of device operation. explained. To access the switches, open the lid of the battery compartment. 3. Relative humidity of the air (RH%). While batteries remain inserted, adjust the pin position (up or down) using the pin tool that has been supplied with the 4. Battery level. Aranet4 device (or any other suitable thin tool). 5. Buzzer status. The speaker symbol is visible when buzzer Switches can be adjusted while batteries are removed as function is activated. The conditions when buzzer should well. Note that if you remove the batteries, the measurement sound is adjusted using the Aranet4 application.

history will be erased. The changed preference setting will be Using Aranet4 device with the Aranet PRO enabled once the batteries are reinserted. base station The position of the switches has the following meaning: The Aranet PRO base station serves as a device for collecting, AUTO / MANUAL - switch the CO2 calibration mode to either storing and maintaining data from all types of Aranet sensors, manual (default position) or automatic mode. including Aranet4. Each Aranet PRO base station can connect The Aranet4 device is calibrated at the factory. However, up to 100 sensors and stores the measurement data in its local the user can perform CO2 calibration manually if required. memory for up to 10 years. To initiate the manual CO2 calibration, change the switch Find out more about the Aranet PRO base station at position from MANUAL to AUTO and back to MANUAL www.aranet.com and follow the User Guide on how to pair (maintain maximum 1 sec between each movement of Aranet sensors to the Aranet PRO base station. switch positions). Indication about started calibration and its progress will be displayed on the screen. Do not To connect the Aranet4 device to the Aranet PRO base station, interrupt the calibration process once it has started. initiate the sensor pairing mode on the Aranet PRO base station During the manual calibration the Aranet4 device must be and initiate the pairing on the Aranet4 device by changing exposed to fresh air (about 400 ppm of CO2) and the environment the switch position from disable (0) to enable (radio symbol). should be stable (not changing). Maintain a distance of at least Alternatively, while switch position is in enable position (radio 1 meter from the device during the calibration process. In case symbol on screen is visible), remove and reinsert the batteries. of calibration failure, ensure that the environment fits the Please note, that removing battery, the measurement history requirements and repeat the process. will be erased from the Aranet4 memory. Manual calibration can be initiated using the Aranet4 app as well. Return and Warranty In case of automatic calibration mode, the Aranet4 device needs In case of return or warranty claim, please contact your to be exposed to a fresh air at around 400 ppm (for instance, sales representative. For Terms and Conditions refer to outdoors or room with good air exchange) daily. www.aranet.com/support/ Use MANUAL calibration mode in case you are not certain which mode to use. °C / °F - switch to either Celsius or Fahrenheit degrees. Bluetooth / 0 - enable or disable (0) the Bluetooth connectivity. Aranet radio / 0 - enable or disable (0) the Aranet radio connectivity. Refer to chapter Using Aranet4 device with the Aranet PRO base station. How to pair the Aranet4 to my smart device The Aranet4 device can be connected to a smart device using the Bluetooth connection and the Aranet4 app (iPhone and Android based). Make sure Bluetooth connectivity is enabled on your smart device and on your Aranet4 device. To connect your Aranet4 device to your smart device follow the below steps: • Launch the Aranet4 app and on the main page (My devices) add a new device by clicking on the (+) symbol. • Select your Aranet4 device from the list. • When prompted, confirm the start of pairing. • Type in the 6 digit passcode that is shown on the display of your Aranet4 device. For more detailed information about Aranet products visit www.aranet.com, contact your Aranet representative or write to info@aranet.com. Product specifications are subject to change without prior notice. Copyright © 2019 SAF Tehnika, JSC. All rights reserved.


Document Created: 2019-08-19 09:56:01
Document Modified: 2019-08-19 09:56:01
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC