Modular Appr Letter

FCC ID: W95-23A00L83

Cover Letter(s)

Download: PDF
FCCID_4439927

Applicant/Grantee
FCC ID:                  W95—23A00L83                  |                     |
                                     Section 15.212 Modular Transmitters /
     Request for Modular Approval |            | Request for Limited Modular Approval
                    Requirements                               Device Conditions                     Comply (Y/N)
                                    Single Modular Approval Requirements
          The radio elements must have the radio           This module has shielding case.
          frequency circuitry shielded.
          |Physical/discrete and tuning capacitors
          may be located external to the shield, but
          must be on the module assembly.

       The module shall have buffered               All modulation and data input(s) are
       modulation/data input(s) (if such inputs are buffered. The EUT has buffered data
       jprovided) to ensure that the module will    inputs, it is integrated on the RF chip
       comply with the requirements set out in the
       applicable RSS standard under conditions
       lof excessive data rates or over—modulation.

       [The module shall have its own power                RF system on Chip IC contains multiple
       supply regulation on the module. This is to         dedicated voltage/power regulators for
       ensure that the module will comply with             transmitter chain including oscillator,
       (the requirements set out in the applicable         modulator and power amplifier.
       standard regardless of the design of the
       jpower supplying circuitry in the host
       device which houses the module.
       Requirements set out in the applicable
       standard regardless of the
       design of the power supplying circuitry in
       the host device which houses the module.
       The module shall comply with the             The Module has a Printed antenna.
       jprovisions for external power amplifiers
       land antennas detailed in this standard. The
       Equipment certification submission shall
       contain a detailed description of the
       configuration of all antennas that will be
       jused with the module.




       The module shall be tested for compliance See Setup Photos
       |with the applicable standard in a stand—
       lalone configuration, i.e. the module must
       Inot be inside another device during testing.


       The modular transmitter must be                 See Label Exhibit
       equipped with either a permanently affixed
       label.


         [The modular transmitter complies with all   Instructions in User Manual
         specific rules or operating requirements
         [that ordinarily apply to a complete
         transmitter and the manufacturer will
    7    provide adequate instructions along with                                                       y
         the module to explain any such
         requirements. A copy of these instructions
         is included in this application for
         lequipment authorization:

         |Address compliance with the                 Instructions are given in the installation
         Commission‘s RF exposure limits in           manual for compliance to the RF
         Sections 1.1310 and 2.1093. In addition,     exposure requirements.
         spread spectrum transmitters operating
         junder Section 15.247 are required to
         laddress RF exposure compliance in
         accordance with Section 15.247(b)(4).

A limited modular approval may be granted for single or split modular transmitters that do not comply with
all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or
power supply regulation, if the manufacturer can demonstrate by alternative means in the application for
equipment authorization that the modular transmitter meets all the applicable Part 15 requirements under the
operating conditions in which the transmitter will be used. Limited modular approval also may be granted in
those instances where compliance with RF exposure rules is demonstrated only for particular product
configurations. The applicant for certification must state how control of the end product into which the module
will be installed will be maintained such that full compliance of the end product is always ensured.




                                         J
          cmmmmiimenaisns
                                      //
                                     (/
                                     /
                                     /
                                 /



siztmuie
  g AL/O
         Cl(— /n
Name/Title: Thomas MAIER
                                                       plotnnm
                                                         Jullug Blum   GmbH
Company Name: Julius Blum GmbH                           sescma;;?abrri?(
Date: 10 Aug                                             A—6973 Hochst, Austria

2019



Document Created: 2019-10-09 03:29:05
Document Modified: 2019-10-09 03:29:05

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC