BT BLE RF test report FCC ID W38-28010077

FCC ID: W38-28010161

Test Report

Download: PDF
FCCID_4181215

RF TEST REPORT Report No.: FCC_RF_SL15060501-CPC-006-DTS Supersede Report No.: None Applicant : ChargePoint, Inc. Product Name : Network Communication Model No. : 28010077 47 CFR 15.247 Test Standard : RSS 210 Issue8: 2010 ANSI C63.10: 2013 Test Method : RSS Gen issue4 558074 D01 DTS Meas Guidance v03r02 FCC ID : W38-28010077 IC ID : 8854A-28010077 Dates of test : June 24, 2015 to July 20, 2015 Issue Date : July 23, 2015 Test Result : ☒ Pass ☐ Fail Equipment complied with the specification [X] Equipment did not comply with the specification [ ] This Test Report is Issued Under the Authority of: Teody Manansala Nima Molaei Test Engineer Engineer Reviewer Issued By: SIEMIC Laboratories 775 Montague Expressway, Milpitas, 95035 CA 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 2 of 33 Laboratory Introduction SIEMIC, headquartered in the heart of Silicon Valley, with superior facilities in US and Asia, is one of the leading independent testing and certification facilities providing customers with one-stop shop services for Compliance Testing and Global Certifications. In addition to testing and certification, SIEMIC provides initial design reviews and compliance management throughout a project. Our extensive experience with China, Asia Pacific, North America, European, and International compliance requirements, assures the fastest, most cost effective way to attain regulatory compliance for the global markets. Accreditations for Conformity Assessment Country/Region Accreditation Body Scope USA FCC, A2LA EMC, RF/Wireless, Telecom Canada IC, A2LA, NIST EMC, RF/Wireless, Telecom Taiwan BSMI, NCC, NIST EMC, RF, Telecom, Safety Hong Kong OFTA, NIST RF/Wireless, Telecom Australia NATA, NIST EMC, RF, Telecom, Safety Korea KCC/RRA, NIST EMI, EMS, RF, Telecom, Safety Japan VCCI, JATE, TELEC, RFT EMI, RF/Wireless, Telecom Mexico NOM, COFETEL, Caniety Safety, EMC, RF/Wireless, Telecom Europe A2LA, NIST EMC, RF, Telecom, Safety Israel MOC, NIST EMC, RF, Telecom, Safety Accreditations for Product Certifications Country Accreditation Body Scope USA FCC TCB, NIST EMC, RF, Telecom Canada IC FCB, NIST EMC, RF, Telecom Singapore iDA, NIST EMC, RF, Telecom EU NB EMC & R&TTE Directive Japan MIC (RCB 208) RF, Telecom Hong Kong OFTA (US002) RF, Telecom 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 3 of 33 CONTENTS 1 REPORT REVISION HISTORY .......................................................................................................................................4 2 EXECUTIVE SUMMARY.................................................................................................................................................5 3 CUSTOMER INFORMATION ..........................................................................................................................................5 4 TEST SITE INFORMATION ............................................................................................................................................5 5 MODIFICATION .............................................................................................................................................................5 6 EUT INFORMATION ......................................................................................................................................................6 6.1 EUT Description ........................................................................................................................................................6 Radio Description ...............................................................................................................................................................6 Spec for BT Radio ..............................................................................................................................................................6 6.2 EUT test modes/configuration Description....................................................................................................................6 6.3 EUT Photos ..............................................................................................................................................................7 6.4 EUT Test Setup Photos .............................................................................................................................................9 7 SUPPORTING EQUIPMENT/SOFTWARE AND CABLING DESCRIPTION ....................................................................... 10 7.1 Supporting Equipment ............................................................................................................................................. 10 7.2 Cabling Description ................................................................................................................................................. 10 7.3 Test Software Description ........................................................................................................................................ 10 8 TEST SUMMARY ......................................................................................................................................................... 11 9 MEASUREMENT UNCERTAINTY ................................................................................................................................. 12 10 MEASUREMENTS, EXAMINATION AND DERIVED RESULTS .................................................................................. 13 10.1 Conducted Emissions .......................................................................................................................................... 13 10.2 Output Power (Bluetooth LE) ................................................................................................................................ 16 10.3 Band Edge (Bluetooth LE) ................................................................................................................................... 18 10.4 99% Occupied Bandwidth (Bluetooth LE) .............................................................................................................. 20 10.5 6dB Bandwidth (Bluetooth LE) .............................................................................................................................. 22 10.6 Peak Spectral Density (Bluetooth LE) ................................................................................................................... 24 10.7 Transmitter Radiated Spurious Emissions Below 1GHz .......................................................................................... 26 10.8 Transmitter Radiated Spurious Emissions > 1GHz & Restricted band....................................................................... 28 ANNEX A. TEST INSTRUMENT ........................................................................................................................................... 31 ANNEX B. SIEMIC ACCREDITATION ................................................................................................................................... 32 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 4 of 33 1 Report Revision History Report No. Report Version Description Issue Date FCC_RF_SL15060501-CPC-006-DTS None Original 07/23/2015 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 5 of 33 2 Executive Summary The purpose of this test program was to demonstrate compliance of following product Company: ChargePoint, Inc. Product: Network Comunication Model: 28010077 against the current Stipulated Standards. The specified model product stated above has demonstrated compliance with the Stipulated Standard listed on 1st page. 3 Customer information Applicant Name : ChargePoint, Inc. Applicant Address : 254 E. Hacienda Ave Campbell, CA 95148 Manufacturer Name : ChargePoint, Inc. Manufacturer Address : 254 E. Hacienda Ave Campbell, CA 95148 4 Test site information Lab performing tests SIEMIC Laboratories Lab Address 775 Montague Expressway, Milpitas, CA 95035 FCC Test Site No. 881796 IC Test Site No. 4842D-2 VCCI Test Site No. A0133 5 Modification Index Item Description Note - - - - 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 6 of 33 6 EUT Information 6.1 EUT Description Product Name Network Comunication Model No. 28010077 Trade Name ChargePoint, Inc. Serial No. N/A Host Model No. N/A Input Power 100-240VDC, 50/60Hz Power Adapter Manu/Model Condor/HK-CH13-A05 Power Adapter SN N/A Product Hardware version 27-010077 Product Software version 4.0.0.41 Radio Hardware version 27-010077 Radio Software version 4.0.0.41 Test Software version 4.0.0.41 Date of EUT received June 20, 2015 Equipment Class/ Category DTS Operating Frequencies 2402MHz-2480MHz Port/Connectors N/A Radio Description Spec for BT Radio Radio Type Bluetooth (Ver4.0+EDR) Operating Frequency 2402MHz-2480MHz Modulation FHSS (BDR, EDR), DSSS (LE) Channel Spacing 1MHz (BDR, EDR), 2MHz (LE) Antenna Type Prestta Embedded Antenna Antenna Gain 2.5dBi (2.4GHz) Antenna Connector Type On Board Channel List Type Channel No. Frequency (MHz) Available (Y/N) 0 2402 Y … … Y Bluetooth LE 19 2440 Y … … Y 39 2480 Y 6.2 EUT test modes/configuration Description Mode Note Bluetooth LE LE (GFSK) 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 7 of 33 6.3 EUT Photos EUT Top View EUT Bottom View PCBA2 –Top View PCBA2 –Top View Power Supply – Top View Power Supply – Bottom View 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 8 of 33 EUT Radio with shielding EUT Radio without shielding Antenna 1 Antenna 2 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 9 of 33 6.4 EUT Test Setup Photos AC Line Conducted Emissions – Front View AC Line Conducted Emissions – Rear View Radiated Emissions (<1GHz) – Front View Radiated Emissions (<1GHz) – Rear View Radiated Emissions (>1GHz) – Front View Radiated Emissions (>1GHz) – Rear View 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 10 of 33 7 Supporting Equipment/Software and cabling Description 7.1 Supporting Equipment Supporting Equipment Item Model Serial Number Manufacturer Note Description 1 Laptop P05F Latitude E5510 N/A Dell - 7.2 Cabling Description Connection Start Connection Stop Length / shielding Info Name Note From I/O Port To I/O Port Length (m) Shielding USB EUT I/O Port Laptop USB 1 Unshielded - 7.3 Test Software Description Test Item Software Description RF Testing Tera Term Set the EUT to transmit continuously in diferent test mode 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 11 of 33 8 Test Summary Test Item Test standard Test Method/Procedure Pass / Fail ANSI C63.10: 2013 ☒ Pass Restricted Band of Operation FCC 15.205 FCC 558074 D01 DTS Meas Guidance v03r02 ☐ N/A AC Conducted Emissions ☒ Pass FCC 15.207(a) FCC ANSI C63.10: 2013 Voltage ☐ N/A DTS band Requirement Test Item Test standard Test Method/Procedure Pass / Fail FCC 15.247 (a)(1) FCC - ☐ Pass Channel Separation IC RSS210 (A8.1) IC - ☒ N/A ☒ Pass 99% Occupied Bandwidth IC RSS210(A8.1) IC RSS Gen (6.6) ☐ N/A FCC 15.247(a)(2) FCC 558074 D01 DTS Meas Guidance v03r02 ☒ Pass 6db Bandwidth IC RSS210 (A8.2) IC - ☐ N/A FCC 15.247(a)(1) FCC - ☐ Pass Number of Hopping Channels IC RSS210(A8.1) IC - ☒ N/A ANSI C63.10: 2013 Band Edge and Radiated FCC 15.247(d) FCC ☒ Pass 558074 D01 DTS Meas Guidance v03r02 Spurious Emissions ☐ N/A IC RSS210(A8.5) IC - FCC 15.247(a)(1) FCC - ☐ Pass Time of Occupancy IC RSS210(A8.1) IC - ☒ N/A FCC 15.247(b) FCC 558074 D01 DTS Meas Guidance v03r02 ☒ Pass Output Power IC RSS210 (A8.4) IC - ☐ N/A ☐ Pass Receiver Spurious Emissions IC RSS Gen (7.1) IC RSS Gen (7.1) ☒ N/A FCC 15.247(e) FCC - ☐ Pass Antenna Gain > 6 dBi IC RSS210(A8.4) IC - ☒ N/A FCC 15.247(e) FCC 558074 D01 DTS Meas Guidance v03r02 ☒ Pass Power Spectral Density IC RSS210(A8.3) IC - ☐ N/A FCC 15.247(f) FCC - ☐ Pass Hybrid System Requirement IC RSS210(A8.3) IC - ☒ N/A FCC 15.247(g) FCC - ☐ Pass Hopping Capability IC RSS210(A8.1) IC - ☒ N/A Hopping Coordination FCC 15.247(h) FCC - ☐ Pass Requirement IC RSS210(A8.1) IC - ☒ N/A FCC 15.247(i) FCC - ☐ Pass RF Exposure requirement IC RSS Gen(3.2) IC - ☒ N/A 1. All measurement uncertainties do not take into consideration for all presented test results. Remark 2. The applicant shall ensure frequency stability by showing that an emission is maintained within the band of operation under all normal operating conditions as specified in the user’s manual. 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 12 of 33 9 Measurement Uncertainty Emissions Test Item Frequency Range Description Uncertainty Confidence level of approximately 95% (in the case +5.6dB/- Band Edge and Radiated Spurious Emissions 30MHz – 1GHz where distributions are normal), with a coverage 4.5dB factor of 2 (for EUTs < 0.5m X 0.5m X 0.5m) Confidence level of approximately 95% (in the case +4.3dB/- Band Edge and Radiated Spurious Emissions 1GHz – 40GHz where distributions are normal), with a coverage 4.1dB factor of 2 (for EUTs < 0.5m X 0.5m X 0.5m) 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 13 of 33 10 Measurements, Examination and Derived Results 10.1 Conducted Emissions Conducted Emission Limit Frequency ranges Limit (dBuV) (MHz) QP Average 0.15 ~ 0.5 66 – 56 56 – 46 0.5 ~ 5 56 46 5 ~ 30 60 50 Spec Item Requirement Applicable For Low-power radio-frequency devices that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies, within the band 150 kHz to 30 47CFR§ 15.207 a) ☒ MHz, shall not exceed the limits in the following table, as measured using a 50 µ H/50 ohms line impedance stabilization network (LISN). The lower limit applies at the boundary between the frequency ranges. Test Setup - The EUT and supporting equipment were set up in accordance with the requirements of the standard on top of a 1.5m x 1m x 0.8m high, non-metallic table, as shown in Annex B. Procedure - The power supply for the EUT was fed through a 50/50H EUT LISN, connected to filtered mains. - The RF OUT of the EUT LISN was connected to the EMI test receiver via a low-loss coaxial cable. - All other supporting equipment was powered separately from another main supply. Remark EUT tested with AC 110V 60Hz Result ☒ Pass ☐ Fail Test Data ☒ Yes ☐ N/A Test Plot ☒ Yes (See below) ☐ N/A 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 14 of 33 Conducted Emission Test Results (Live) Test specification: Conducted Emissions Temp(° C): 22 Environmental Conditions: Humidity (%): 40 ☒ Pass Atmospheric(mbar): 1022 Result: Mains Power: 110Vac, 60Hz ☐ Fail Tested by: Teody Manansala Test Date: 07/20/2015 Remarks Line Line Plot at 120Vac, 60Hz Frequency Raw Cable Factors Level Measurement Limit Margin Pass Line (MHz) (dBuV) Loss (dB) (dB) (dBuV) Type (dBuV) (dB) /Fail 0.16 49.21 10.00 0.75 59.96 Quasi Peak Live 65.70 -5.73 Pass 0.20 38.38 10.00 0.74 49.13 Quasi Peak Live 63.50 -14.37 Pass 0.26 35.13 10.00 0.72 45.85 Quasi Peak Live 61.35 -15.50 Pass 0.40 21.24 10.01 0.73 31.97 Quasi Peak Live 57.76 -25.79 Pass 2.42 20.32 10.03 0.96 31.30 Quasi Peak Live 56.00 -24.70 Pass 0.48 21.13 10.01 0.74 31.88 Quasi Peak Live 56.27 -24.39 Pass 0.16 30.68 10.00 0.75 41.44 Average Live 55.70 -14.26 Pass 0.20 18.69 10.00 0.74 29.43 Average Live 53.50 -24.06 Pass 0.26 18.14 10.00 0.72 28.86 Average Live 51.35 -22.49 Pass 0.40 11.19 10.01 0.73 21.92 Average Live 47.76 -25.84 Pass 2.42 11.90 10.03 0.96 22.89 Average Live 46.00 -23.11 Pass 0.48 11.38 10.01 0.74 22.12 Average Live 46.27 -24.15 Pass Note: The results above show only the worst case. 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 15 of 33 Conducted Emission Test Results (Neutral) Test specification: Conducted Emissions Temp(° C): 22 Environmental Conditions: Humidity (%): 40 ☒ Pass Atmospheric(mbar): 1022 Result: Mains Power: 110Vac, 60Hz ☐ Fail Tested by: Teody Manansala Test Date: 07/20/2015 Remarks Neutral Neutral Line Plot @ 120Vac, 60Hz Frequency Raw Cable Factors Level Measurement Limit Margin Pass Line (MHz) (dBuV) Loss (dB) (dB) (dBuV) Type (dBuV) (dB) /Fail 0.15 46.64 10.00 0.76 57.39 Quasi Peak Neutral 65.77 -8.38 Pass 0.21 39.09 10.00 0.74 49.83 Quasi Peak Neutral 63.20 -13.37 Pass 0.26 32.79 10.00 0.72 43.51 Quasi Peak Neutral 61.47 -17.96 Pass 2.38 21.17 10.03 0.96 32.16 Quasi Peak Neutral 56.00 -23.84 Pass 3.16 23.09 10.03 0.99 34.11 Quasi Peak Neutral 56.00 -21.89 Pass 3.20 18.31 10.03 1.00 29.33 Quasi Peak Neutral 56.00 -26.67 Pass 0.15 27.55 10.00 0.76 38.31 Average Neutral 55.77 -17.46 Pass 0.21 24.60 10.00 0.74 35.34 Average Neutral 53.20 -17.86 Pass 0.26 14.53 10.00 0.72 25.26 Average Neutral 51.47 -26.22 Pass 2.38 12.16 10.03 0.96 23.14 Average Neutral 46.00 -22.86 Pass 3.16 13.16 10.03 0.99 24.18 Average Neutral 46.00 -21.82 Pass 3.20 10.31 10.03 1.00 21.34 Average Neutral 46.00 -24.66 Pass Note: The results above show only the worst case. 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 16 of 33 10.2 Output Power (Bluetooth LE) Requirement(s): Spec Item Requirement Applicable a) FHSS in 2400-2483.5MHz with ≥ 75 channels: ≤1 Watt ☐ b) FHSS in 5725-5850MHz: ≤1 Watt ☐ c) For all other FHSS in the 2400-2483.5MHz band: ≤0.125 Watt. ☐ § 15.247 d) FHSS in 902-928MHz with ≥ 50 channels: ≤1 Watt ☐ e) FHSS in 902-928MHz with ≥ 25 & <50 channels: ≤0.25 Watt ☐ f) DSSS in 902-928MHz, 2400-2483.5MHz, 5725-5850MHz: ≤1 Watt ☒ Test Setup Measurement using a Power Meter (PM) Measurements may be performed using a wideband gated RF power meter provided that the gate parameters are adjusted such that the power is measured only when the EUT is transmitting at its maximum power control level. Since the measurement is made only during the ON time of the transmitter, no duty cycle correction factor Test Procedure is required. - Connect EUT’s RF output power to power meter - Set EUT to be continuous transmission mode - Measurement the average output power using power meter and record the result - Repeat above steps for different test channel and other modulation type. Temperature 23ºC Environmental Test Date 07/02/2015 Relative Humidity 44% condition Atmospheric Pressure 1021mbar Remark - Result ☒ Pass ☐ Fail Test Data ☒ Yes ☐ N/A Test Plot ☐ Yes (See below) ☒ N/A 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 17 of 33 Output Power measurement result (Bluetooth) Limit Type Test mode Freq (MHz) CH Conducted Result (dBm) Power (dBm) Output power Bluetooth LE 2402 Low 1.9 30 Pass Output power Bluetooth LE 2440 Mid 1.6 30 Pass Output power Bluetooth LE 2480 High 1.2 30 Pass 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 18 of 33 10.3 Band Edge (Bluetooth LE) Requirement(s): Spec Item Requirement Applicable For non-restricted band, In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB or 30dB below that in the 100 kHz bandwidth within the band that § 15.247 d) ☒ contains the highest level of the desired power, determined by the measurement method on output power to be used. Attenuation below the general limits specified in § 15.209 (a) is not required ☐ 20 dB down ☒ 30 dB down Test Setup 558074 D01 DTS Meas Guidance v03r02 Band Edge measurement procedure 1. Set the EUT to maximum power setting and enable the EUT transmit continuously. Test Procedure 2. Band edge emissions must be at least 30 dB down from the highest emission level within the authorized band as a measured. The attunation shall be be 30 dB instead of 20 dB when RMS conducted output power procedure is used. 3. Change modulation and channel bandwidth then repeat step 1 to 2. 4. Measured and record the results in the test report. Temperature 22ºC Environmental Test Date 07/02/2015 Relative Humidity 46% condition Atmospheric Pressure 1020mbar Remark - Result ☒ Pass ☐ Fail Equipment Setting TEST RBW VBW SPAN Detector SWEEP Trace NOTES Band Edge 100KHz ≥3 x RBW 135 MHz / 55 MHz Peak Auto Peak MAX - Test Data ☐ Yes ☒ N/A Test Plot ☒ Yes (See below) ☐ N/A 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 19 of 33 Band Edge Test Plots (Bluetooth LE) Band Edge-LE Low Band Edge-LE High 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 20 of 33 10.4 99% Occupied Bandwidth (Bluetooth LE) Requirement(s): Spec Requirement Applicable The transmitter shall be operated at its maximum carrier power measured under normal test conditions. The span of the analyzer shall be set to capture all products of the modulation process, including the emission skirts. The resolution bandwidth shall be set to as close to 1% of the selected span as is possible without being below 1%. The video bandwidth shall be set to 3 times the resolution bandwidth. Video averaging is not permitted. Where practical, a sampling detector RSS Gen 4.6.1 shall be used given that a peak or peak hold may produce a wider bandwidth than actual. The ☒ trace data points are recovered and directly summed in linear terms. The recovered amplitude data points, beginning at the lowest frequency, are placed in a running sum until 0.5% of the total is reached and that frequency recorded. The process is repeated for the highest frequency data points. This frequency is recorded. The span between the two recorded frequencies is the occupied bandwidth Test Setup 1. EUT was set for low , mid, high channel with modulated mode and highest RF output power. Procedure 2. The spectrum analyzer was connected to the antenna terminal. Temperature 23oC Test Date 07/02/2015 Environmental condition Relative Humidity 47% Atmospheric Pressure 1019mbar Remark - Result ☒ Pass ☐ Fail Test Data ☒ Yes (See below) ☐ N/A Test Plot ☒ Yes (See below) ☐ N/A 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 21 of 33 99%dB Bandwidth measurement result for Bluetooth LE Type Test mode Freq (MHz) CH Result (MHz) Limit (MHz) Result 99% BW BT-LE 2402 Low 1.0941 N/A N/A 99% BW BT-LE 2440 Mid 1.0947 N/A N/A 99% BW BT-LE 2480 High 1.0948 N/A N/A 99%dB Bandwidth Test Plot (Bluetooth LE) 99% BW –Bluetooth LE 2402MHz 99% BW –Bluetooth LE 2440MHz 99% BW –Bluetooth LE 2480MHz 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

’fl Test report No. FCC_RF_SL15060501—CPC—006—DTS SIEMIC Page 22 of 33 GLOBAL TESTING & CERTIFICATIONS Your choice ron—rce rce ca o can rce 10.5 6dB Bandwidth (Bluetooth LE Requirement(s): Spec Item Requirement Applicable §15.247 a)(2) 60B BW>500KHz; Test Setup 9:..] ———— Spectrum Analyzer 558074 D01 DTS Meas Guidance v03r02, 8.1 DTS bandwidth 6dB Emission bandwidth measurement procedure — Set RBW = 100 kHz. — Set the video bandwidth (VBW) > 3x RBW. Test Procedure — Detector = Peak. — Trace mode= max hold. — Sweep= auto couple. — Allow the frace to stabilize. — Measure the maximum width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower frequencies) that are attenuated by 6 dB relative to the maximum leve! measured in the fundamental emission. ; Temperature 249C Test Date 071022015 Eofoicy©. Relative Humidity 42% Atmospheric Pressure 1021mbar Remark N/A Result Pass C Fail Equipment Setting TEST RBW VBW SPAN Detector SWEEP Trace NOTES 60B DTS Bandwidth 100KHz 3x RBW ~EBW PK Auto Max hold — Test Data Yes C NA Test Plot Yes C NA 775 Montague Expressway, Milpitas, CA 95035, USA + Phone: (+1) 408 526 1188 * Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at: n

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 23 of 33 6dB Bandwidth measurement result for Bluetooth LE Type Test mode Freq (MHz) CH Result (MHz) Limit (MHz) Result 6dB BW Bluetooth LE 2402 Low 0.601 ≥0.5 Pass 6dB BW Bluetooth LE 2440 Mid 0.601 ≥0.5 Pass 6dB BW Bluetooth LE 2480 High 0.604 ≥0.5 Pass 6dB Bandwidth Test Plots( Bluetooth LE) 6dB BW –Bluetooth LE 2402MHz 6dB BW –Bluetooth LE 2440MHz 6dB BW –Bluetooth LE 2480MHz 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

’fl Test report No. FCC_RF_SL15060501—CPC—006—DTS SIEMIC Page 24 of 33 GLOBAL TESTING & CERTIFICATIONS Your choice ron—rce rce ca o can rce 10.6 Peak Spectral Density (Bluetooth LE) Requirement(s): Spec Item_| Requirement Applicable €) DSSS: <8dBm/3KHz §15.247(e) — — — — 1 DSSS in hybrid sys with FH turned off. <8dBm/3KHz C Test Setup Es} ————(sx) Spectrum C Analyzer 558074 DO1 DTS Meas Guidance v03r02, 10.3 Method AVGPSD—1 Peak spectral density measurement procedure — Setanalyzer center frequency to DTS channel center frequency. — Set the span to 1.5 times the DTS bandwidth. — Set the RBW to: 3 kHz = RBW = 100 kHz. Test Procedure — Setthe VBW > 3x RBW, — Detector= RMS — Sweep time= auto couple. — Trace mode = Trace average over 100 traces — Allow trace to fully stabllize. — Use the peak marker function to determine the maximum amplitude leve! within the RBW. — If measured value exceeds limit, reduce RBW (no less than 3 kHz) and repeat. Environmental Temperature 22C Test Date 0710212015 condition Relative Humidity 46% Atmospheric Pressure 1020mbar Remark — Result Pass C Fall Equipment Setting TEST RBW VBW SPAN Detector SWEEP Trace NOTES PSD 100KHz >3x RBW 1.6x DTS BW RMS Auto Trace average — Test Data Yes C N/A Test Plot Yes (See below) C NA 775 Montague Expressway, Milpitas, CA 95035, USA + Phone: (+1) 408 526 1188 * Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at: n

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 25 of 33 PSD measurement result (Bluetooth LE) Freq Conducted PSD Limit Type Test mode CH Result (MHz) (dBm/100KHz) (dBm/3KHz) PSD Bluetooth LE 2402 Low 5.558 ≤8 Pass PSD Bluetooth LE 2440 Mid 5.298 ≤8 Pass PSD Bluetooth LE 2480 High 4.805 ≤8 Pass Test Plots (Bluetooth LE) PSD -Bluetooth LE Low PSD -Bluetooth LE Mid PSD -Bluetooth LE High 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 26 of 33 10.7 Transmitter Radiated Spurious Emissions Below 1GHz Requirement(s): Spec Item Requirement Applicable Except higher limit as specified elsewhere in other section, the emissions from the low-power radio-frequency devices shall not exceed the field strength levels specified in the following table and the level of any unwanted emissions shall not exceed the level of the fundamental emission. The tighter limit applies at the band 47CFR§ 15.247(d), edges ☒ a) RSS210(A8.5) Frequency range (MHz) Field Strength (uV/m) 30 – 88 100 88 – 216 150 216 960 200 Above 960 500 Test Setup 1. The EUT was switched on and allowed to warm up to its normal operating condition. 2. The test was carried out at the selected frequency points obtained from the EUT characterisation. Maximization of the emissions, was carried out by rotating the EUT, changing the antenna polarization, and adjusting the antenna height in the following manner: a. Vertical or horizontal polarisation (whichever gave the higher emission level over a full Procedure rotation of the EUT) was chosen. b. The EUT was then rotated to the direction that gave the maximum emission. c. Finally, the antenna height was adjusted to the height that gave the maximum emission. 3. A Quasi-peak measurement was then made for that frequency point. 4. Steps 2 and 3 were repeated for the next frequency point, until all selected frequency points were measured. The EUT was scanned up to 1GHz. Both horizontal and vertical polarities were investigated. The results Remark show only the worst case. Result ☒ Pass ☐ Fail Test Data ☒ Yes (See below) ☐ N/A Test Plot ☒ Yes (See below) ☐ N/A 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 27 of 33 Radiated Emission Test Results (Below 1GHz) Test specification: Radiated Spurious Emissions (30MHz – 1000MHz) Temp(° C): 20 Environmental Conditions: Humidity (%): 36 ☒ Pass Atmospheric(mbar): 1021 Result: Mains Power: 120VAC, 60Hz ☐ Fail Tested by: Teody Manansala Test Date: 06/26/2015 Remarks: Bluetooth LE 2440MHz Quasi Max Measurement Cable Frequency Raw AF Level Measurement Pol Hgt Azt Limit Margin Pass Loss (MHz) (dBuV) (dB) (dBuV/m) Type (V/H) (cm) (Deg) (dBuV/m) (dB) /Fail (dB) 48.00 59.14 1.12 -28.46 31.80 Quasi Max V 104.00 327.00 40.00 -8.2 Pass 36.00 53.05 1.04 -22.51 31.57 Quasi Max V 110.00 304.00 40.00 -8.43 Pass 71.96 57.42 1.48 -30.04 28.86 Quasi Max V 112.00 31.00 40.00 -11.14 Pass 40.98 45.07 1.07 -25.63 20.52 Quasi Max V 133.00 350.00 40.00 -19.48 Pass 38.90 42.64 1.06 -24.94 18.77 Quasi Max V 136.00 356.00 40.00 -21.23 Pass 37.93 40.87 1.05 -24.09 17.83 Quasi Max V 133.00 54.00 40.00 -22.17 Pass 48.00 59.14 1.12 -28.46 31.80 Quasi Max V 104.00 327.00 40.00 -8.2 Pass 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 28 of 33 10.8 Transmitter Radiated Spurious Emissions > 1GHz & Restricted band Requirement(s): Spec Item Requirement Applicable For non-restricted band, In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB or 30dB below that in the 100 kHz bandwidth within the band that ☒ a) contains the highest level of the desired power, determined by the measurement 47CFR§ 15.247(d), method on output power to be used. Attenuation below the general limits RSS210(A8.5) specified in § 15.209(a) is not required ☐ 20 dB down ☒ 30 dB down or restricted band, emission must also comply with the radiated emission limits b) ☒ specified in 15.209 Test Setup 1. The EUT was switched on and allowed to warm up to its normal operating condition. 2. The test was carried out at the selected frequency points obtained from the EUT characterisation. Maximization of the emissions, was carried out by rotating the EUT, changing the antenna polarization, and adjusting the antenna height in the following manner: a. Vertical or horizontal polarisation (whichever gave the higher emission level over a full Procedure rotation of the EUT) was chosen. b. The EUT was then rotated to the direction that gave the maximum emission. c. Finally, the antenna height was adjusted to the height that gave the maximum emission. 3. An average measurement was then made for that frequency point. 4. Steps 2 and 3 were repeated for the next frequency point, until all selected frequency points were measured. The EUT was scanned up to 40GHz. Both horizontal and vertical polarities were investigated. The results Remark show only the worst case. Result ☒ Pass ☐ Fail Equipment Setting TEST RBW VBW SPAN Detector SWEEP Trace NOTES Radiated Spurious PK 1MHz 3MHz 1GHz - 25 GHz Peak Auto Max hold Emission Measurement Radiated Spurious Ave 1MHz 10Hz 1GHz - 25 GHz Peak Auto Max hold Emission Measurement Test Data ☒ Yes (See below) ☐ N/A Test Plot ☐ Yes (See below) ☒ N/A 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 29 of 33 Test specification: Radiated Spurious Emissions (above 1GHz) Temp(° C): 20 Environmental Conditions: Humidity (%): 36 ☒ Pass Atmospheric(mbar): 1021 Result: Mains Power: 120VA, 60Hz ☐ Fail Tested by: Teody Manansala Test Date: 06/30/2015 Remarks: Bluetooth LE Bluetooth LE – 2402MHz Cable Frequency Raw AF Level Measurement Pol Hgt Azt Limit Margin Pass Loss (MHz) (dBuV) (dB) (dBuV/m) Type (V/H) (cm) (Deg) (dBuV/m) (dB) /Fail (dB) 4135.93 40.37 5.95 11.63 57.95 Peak Max H 177.00 350.00 74.00 -16.05 Pass 2071.91 42.90 3.61 11.25 57.76 Peak Max V 167.00 304.00 74.00 -16.24 Pass 1018.22 44.75 2.45 9.65 56.85 Peak Max V 233.00 248.00 74.00 -17.15 Pass 14781.67 42.02 13.60 7.67 63.29 Peak Max V 199.00 208.00 74.00 -10.71 Pass 4135.93 27.05 5.95 11.63 44.63 Average Max H 177.00 350.00 54.00 -9.37 Pass 2071.91 30.14 3.61 11.25 45.00 Average Max V 167.00 304.00 54.00 -9.00 Pass 1018.22 31.80 2.45 9.65 43.90 Average Max V 233.00 248.00 54.00 -10.10 Pass 14781.67 29.41 13.60 7.67 50.68 Average Max V 199.00 208.00 54.00 -3.32 Pass Bluetooth LE – 2440MHz Cable Frequency Raw AF Level Measurement Pol Azt Limit Margin Pass Loss Hgt (cm) (MHz) (dBuV) (dB) (dBuV/m) Type (V/H) (Deg) (dBuV/m) (dB) /Fail (dB) 4153.69 39.45 5.96 11.56 56.96 Peak Max V 196.00 235.00 74.00 -17.04 Pass 1032.87 44.61 2.46 9.62 56.69 Peak Max V 119.00 93.00 74.00 -17.31 Pass 17711.47 39.76 13.00 10.62 63.38 Peak Max V 204.00 219.00 74.00 -10.62 Pass 14558.92 42.18 13.21 8.26 63.64 Peak Max H 186.00 165.00 74.00 -10.36 Pass 4153.69 26.73 5.96 11.56 44.24 Average Max V 196.00 235.00 54.00 -9.76 Pass 1032.87 31.59 2.46 9.62 43.68 Average Max V 119.00 93.00 54.00 -10.32 Pass 17711.47 27.16 13.00 10.62 50.78 Average Max V 204.00 219.00 54.00 -3.22 Pass 14558.92 29.36 13.21 8.26 50.82 Average Max H 186.00 165.00 54.00 -3.18 Pass Bluetooth LE – 2480MHz Cable Frequency Raw AF Level Measurement Pol Azt Limit Margin Pass Loss Hgt (cm) (MHz) (dBuV) (dB) (dBuV/m) Type (V/H) (Deg) (dBuV/m) (dB) /Fail (dB) 1049.50 43.77 2.47 9.60 55.84 Peak Max V 260.00 283.00 74.00 -18.16 Pass 17726.39 40.15 13.00 10.63 63.78 Peak Max V 263.00 288.00 74.00 -10.22 Pass 2175.31 41.86 4.00 10.93 56.79 Peak Max H 276.00 276.00 74.00 -17.21 Pass 4050.79 40.12 5.87 12.00 58.00 Peak Max H 105.00 113.00 74.00 -16.00 Pass 1049.50 31.38 2.47 9.60 43.45 Average Max V 260.00 283.00 54.00 -10.55 Pass 17726.39 27.23 13.00 10.63 50.86 Average Max V 263.00 288.00 54.00 -3.14 Pass 2175.31 29.09 4.00 10.93 44.02 Average Max H 276.00 276.00 54.00 -9.98 Pass 4050.79 26.56 5.87 12.00 44.44 Average Max H 105.00 113.00 54.00 -9.56 Pass 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 30 of 33 Restricted Band Test plot (Bluetooth BDR/EDR) Marker 2 [T2] RBW 1 MHz RF Att 0 dB Marker 2 [T2] RBW 1 MHz RF Att 0 dB Ref Lvl 54.09 dB  V/m VBW 1 MHz Ref Lvl 47.26 dB  V/m VBW 1 MHz 77 dB* 2.40000000 GHz SWT 5 ms Unit dB  V/m 77 dB* 2.49332064 GHz SWT 5 ms Unit dB  V/m 77 77 2 [T2] 54.09 dB  V/m 2 [T2] 47.26 dB  V/m Peak LIMIT CHECK : PASSED A Peak LIMIT CHECK : PASSED A 2.40000000 GHz 2.49332064 GHz 70 1 [T1] 58.88 dB  V/m 70 1 [T1] 52.65 dB  V/m 2.40000000 GHz 2.48350000 GHz 1 60 60 2 IN1 IN1 Average 1 Average 1MAX 1MA 1MAX 1MA 2MAX 2AV 2MAX 2AV 50 50 2 40 40 TDS TDS 30 30 20 20 10 10 Vasona Emission Software : EMiSoft Vasona Emission Software : EMiSoft 7 7 Start 2.39 GHz 1 MHz/ Stop 2.4 GHz Start 2.4835 GHz 1.65 MHz/ Stop 2.5 GHz Date: 1.JAN.1997 02:20:50 Date: 1.JAN.1997 02:26:43 Restricted Band Low BDR Restricted Band High BDR 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 31 of 33 Annex A. TEST INSTRUMENT Instrument Model Serial # Cal Date Cal Cycle Cal Due In use Conducted Emissions R & S Receiver ESIB 40 100179 05/26/2015 1 Year 05/26/2016 V-LISN (150 kHz – 30 MHz) NNLK 8129 8129-190 08/11/2014 1 Year 08/11/2015 LISN (9 kHz – 30 MHz) MN2050B 1018 07/31/2014 1 Year 07/31/2015 Radiated Emissions R & S Receiver ESL6 100178 05/27/2015 1 Year 05/27/2016 Bi-Log antenna (30MHz~2GHz) JB1 A030702 08/11/2014 1 Year 08/11/2015 Horn Antenna (1-26.5GHz) 3115 10SL0059 08/11/2014 1 Year 08/11/2015 Horn Antenna (18-40 GHz) AH-840 101013 02/19/2015 1 Year 02/19/2016 Pre-Amplifier (1-26.5GHz) 8449B 3008A00715 02/19/2015 1 Year 02/19/2016 Microwave Preamplifier (18-40 PA-840 181251 08/11/2014 1 Year 08/11/2015 GHz) 3 Meters SAC 3M N/A 08/29/2014 1 Year 08/29/2015 10 Meters SAC 10M N/A 09/05/2014 1 Year 09/05/2015 RF Conducted Measurement Spectrum Analyzer N9010A MY50210206 08/13/2014 1 Year 08/13/2015 Power Meter 7002-006 10SL0189 4/30/2015 1 Year 4/30/2016 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 32 of 33 Annex B. SIEMIC Accreditation Accreditations Document Scope / Remark ISO 17025 (A2LA) Please see the documents for the detailed scope ISO Guide 65 (A2LA) Please see the documents for the detailed scope TCB Designation A1, A2, A3, A4, B1, B2, B3, B4, C FCC DoC Accreditation FCC Declaration of Conformity Accreditation FCC Site Registration 3 meter site FCC Site Registration 10 meter site IC Site Registration 3 meter site IC Site Registration 10 meter site Radio & Telecommunications Terminal Equipment: EN45001 – EN ISO/IEC 17025 EU NB Electromagnetic Compatibility: EN45001 – EN ISO/IEC 17025 Singapore iDA Phase I, Phase II CB(Certification Body) Vietnam MIC Please see the document for the detailed scope CAB Accreditation (Phase II) OFCA Foreign Certification Body for Radio and Telecom Hong Kong OFCA (Phase I) Conformity Assessment Body for Radio and Telecom Radio: Scope A – All Radio Standard Specification in Category I Industry Canada CAB Telecom: CS-03 Part I, II, V, VI, VII, VIII 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:

Test report No. FCC_RF_SL15060501-CPC-006-DTS Page 33 of 33 Radio: A1. Terminal equipment for purpose of calling Japan Recognized Certification Telecom: B1. Specified radio equipment specified in Article 38-2, Paragraph 1, Item Body Designation 1 of the Radio Law EMI: KCC Notice 2008-39, RRL Notice 2008-3: CA Procedures for EMI KN22: Test Method for EMI EMS: KCC Notice 2008-38, RRL Notice 2008-4: CA Procedures for EMS KN24, KN61000-4-2, -4-3, -4-4, -4-5, -4-6, -4-8, -4-11: Test Method for EMS Korea CAB Accreditation Radio: RRL Notice 2008-26, RRL Notice 2008-2, RRL Notice 2008-10, RRL Notice 2007-49, RRL Notice 2007-20, RRL Notice 2007-21, RRL Notice 2007- 80, RRL Notice 2004-68 Telecom: President Notice 20664, RRL Notice 2007-30, RRL Notice 2008-7 with attachments 1, 3, 5, 6; President Notice 20664, RRL Notice 2008-7 with attachment 4 LP0002, PSTN01, ADSL01, ID0002, IS6100, CNS14336, PLMN07, PLMN01, Taiwan NCC CAB Recognition PLMN08 Taiwan BSMI CAB Recognition CNS 13438 R-3083: Radiation 3 meter site Japan VCCI C-3421: Main Ports Conducted Interference Measurement T-1597: Telecommunication Ports Conducted Interference Measurement EMC: AS/NZS CISPR 11, AS/NZS CISPR 14.1, AS/NZS CISPR22, AS/NZS 61000.6.3, AS/NZS 61000.6.4 Radio communications: AS/NZS 4281, AS/NZS 4268, AS/NZS 4280.1, AS/NZS 4280.2, AS/NZS 4295, AS/NZS 4582, AS/NZS 4583, AS/NZS 4769.1, Australia CAB Recognition AS/NZS 4769.2, AS/NZS 4770, AS/NZS 4771 Telecommunications: AS/ACIF S002:05, AS/ACIF S003:06, AS/ACIF S004:06 AS/ACIF S006:01, AS/ACIF S016:01, AS/ACIF S031:01, AS/ACIF S038:01, AS/ACIF S040:01, AS/ACIF S041:05, AS/ACIF S043.2:06, AS/ACIF S60950.1 AS/ACIF S002, AS/ACIF S003, AS/ACIF S004, AS/ACIF S006, AS/ACIF Australia NATA Recognition S016,AS/ACIF S031, AS/ACIF S038, AS/ACIF S040, AS/ACIF S041, AS/ACIF S043.2 775 Montague Expressway, Milpitas, CA 95035, USA • Phone: (+1) 408 526 1188 • Facsimile (+1) 408 526 1088 Visit us at: www.siemic.com; Follow us at:


Document Created: 2019-03-27 11:26:25
Document Modified: 2019-03-27 11:26:25
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC