Users Manual

FCC ID: W2Z-02000003

Users Manual

Download: PDF
FCCID_3151131

User Manual WIRELESS LAN MODULE MODEL FZ00010935-700 The purpose of this manual is to explain correct way how to integrate module FZ00010935-700 to the end product. It includes procedures that shall assist you to avoid unforeseen problems. This manual presents information that shows how module and OEM product, where module integrated,complies with regulations in certain regions. Any modifications, not expressly approved by the manufacturer could void the authority to operate in these regions. The wireless LAN module, model FZ00010935-700 has to be installed and used in accordance with the technical description/installation instructions provided by the manufacturer. For detail information concerning type approval of this module (e.g. where this module is already pre-approved) please contact the authorized local distributor or the manufacturer. The system may only be implemented in the configuration that was authorized. Note that any changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment.

Regulatory Information Operational Information Wireless Interoperability The end product integrating this module is designed to be interoperable with any wireless LAN product that is based on direct sequence spread spectrum (DSSS) and orthogonal frequency division multiplexing (OFDM) radio technology and to comply with the following standards. ･IEEE Std 802.11b Standard on 2.4GHz Wireless LAN ･IEEE Std 802.11g Standard on 2.4GHz Wireless LAN ･IEEE Std 802.11ｎ Standard on 2.4GHz Wireless LAN Federal Communications Commission (FCC) Statement 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. 15.21: You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. FCC RF Radiation Exposure Statement: 1.This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2.This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

FCC RF Exposure requirements: This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. 15.19 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference and 2) this device must accept any interference received, including interference that may cause undesired operation of the device. Labeling: Wireless LAN module FZ00010935-700 labeled as below. FCC ID: W2Z-02000003 The proposed with FCC ID label format is to be placed on the module. If FCC ID is not visible when the module is installed into the system, “Contains FCC ID: W2Z-02000003” shall be placed on the outside of final host system

Instructions to OEM Integrators A User manual provided to the end user must indicate the operating requirements and conditions that must be observed to ensure compliance with the above-mentioned FCC RF Exposure guideline. If this module is intended for use in a portable device, integrators are responsible for separate evaluation and/or approval to satisfy FCC RF Exposure requirements. The antenna used this module is as follows; Antenna Type: PCB printed antenna Antenna Gain: -4.14dBi If an antenna with higher gain or new antenna type is used with this module, integrators must contact to manufacture for additional testing and submission to the FCC. If other radio devices are to be integrated with this module, an additional evaluation and FCC submission may be required. Integrators are responsible for such additional evaluation and FCC submission.

Industry Canada Statement This device complies with RSS-247 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. RF Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Avis d’industrie Canada: Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et, and (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement. RF exposure: To comply with the IC RF exposure compliance requirements, this device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. Pour se conformer aux exigences de conformité RF canadienne l'exposition, cet appareil et son antenne ne doivent pas être co-localisés ou fonctionnant en conjonction avec une autre antenne ou transmetteur. Industry Canada Class B Emission Compliance Statement: This Class B digital apparatus complies with Canadian ICES-003. Avis de conformite a la reglementation d'Industrie Canada: Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada. Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.

Labeling: Wireless LAN module FZ00010935-700 labeled as below. IC: 7736B-02000003 The proposed with IC ID label format is to be placed on the module. If IC ID is not visible when the module is installed in to the system, “Contains IC: 7736B-02000003” shall be placed on the outside of final host system.

Instructions to OEM Integrators A User manual provided to the end user must indicate the operating requirements and conditions that must be observed to ensure compliance with the above-mentioned IC RF Exposure guideline. If this module is intended for use in a portable device, integrators are responsible for separate evaluation and/or approval to satisfy IC RF Exposure requirements. The antenna used this module is as follows; Antenna Type: PCB printed antenna Antenna Gain: -4.14dBi If an antenna with higher gain or new antenna type is used with this module, integrators must contact manufacture for additional testing and submission to the IC. If other radio devices are to be integrated with this module, an additional evaluation and IC submission may be required. Integrators are responsible for such additional evaluation and IC submission. Notice. Since this module is not sold to general end users directly, there is no user manual of module. For the details about this module, please refer to the specification sheet of module.(Next Page) This module should be installed in the host device according to the interface specification (installation procedure). This module built-in use in equipment. If you do not include the module to the equipment,only be operated by “TX continue” and “RX continue” stand alone mode separated.

MODULE SPECIFICATION Contents. No. Item 1 Product summary 1-1 Scope 1-2 General explanation 2 Hardware specification 2-1 Block diagram 2-2 Environmental condition 2-3 Power supply 3 Electrical characteristics 3-1 Channel plan 3-2 Power Sequence 3-3 Interface specification 3-4 SDIO Protocol Timing 3-5 Current consumption 3-6 Reciever characteristics 3-7 Transmitter characteristics 4 Mechanical specification 4-1 Dimension 4-2 Weight 4-3 Terminal number and name 4-4 Module Overall Appearance 5 Revision

1.Product Summary 1-1.Scope 2.4 GHz WLAN module with integrated antenna (IEEE 802.11 b/g/n supported) 1-2.General explanation Standard IEEE802.11b/g/n Frequency 2.4-2.4835GHz Host Interfase SDIO ver2.0 Frequency Bandwidth 20MHz,40MHz Weight 0.5g typ ・Chipset:MediaTek Inc.RT6370(WLCSP Package) ・Modulation Types: DBPSK, DQPSK and CCK with 802.11b mode OFDM(BPSK, QPSK, 16-QAM and 64-QAM) with 802.11g/n mode ・Data rate: 1,2,5.5 and 11 with 802.11b mode 6,9,12,18,24,36,48 and 54 with 802.11g mode MCS0-7 with 802.11n mode ・Security: WEP(64 and 128bits), WPA-PSK(TKIP/AES) and WPA2-PSK(TKIP/AES) 2.Hardware Specification 2-1. Block diagram 2-2.Environmental condition 1) Operating environment Operating temperature range : -20 ～ 85 ℃ ※Temperature on the bottom of the module Operating humidity range: 20%～80% (None dew) 2) Storage environment Storage temperature range: -30 ～ 85 ℃ Storage humidity range 20%～85% (None dew)

2-3.Power supply Symbol Min.[V] TYP． Max.[V] VDD33 3.14 - 3.46 VIO 1.60 - 3.46 3.Electrical Characteristics 3-1.Channel Plan IEEE802.11b/g/n(HT20) CH ID Freq.[MHz] CH ID Freq.[MHz] CH ID Freq.[MHz] 1 2412 6 2437 11 2462 2 2417 7 2442 12 2467 3 2422 8 2447 13 2472 4 2427 9 2452 5 2432 10 2457 IEEE802.11n(HT40) CH ID Freq.[MHz] CH ID Freq.[MHz] 1 2422 6 2447 2 2427 7 2452 3 2432 4 2437 5 2442 3-2.Power Sequence Recommended power on timing VDD33 be ready before VIO and then enable PAD_EN for internal PMU blocks

3-3. Interface specification (SDIO) Parameter Min. [V] Typ. Max. [V] Input high voltage 0.625*VIO - VIO+0.3 Input low voltage -0.3 - 0.25*VIO Output high voltage 0.75*VIO - - Output low voltage - 0.125*VIO 3-4. SDIO Protocol Timing 3-4-1 Normal Mode 3-4-2 High Speed Mode

3-4-3. SDIO Timing Data Symbol Parameter Mode Min Typ. Max fpp Clock Frequency Normal 0 [MHz] - 25 [MHz] High Speed 0 [MHz] - 50 [MHz] Twl Clock Low Time Normal 10 [ns] - High Speed 7 [ns] - Twh Clock High Time Normal 10 [ns] - High Speed 7 [ns] - Tisu Input Setup Time Normal 5 [ns] - High Speed 6 [ns] - Tih Input Hold Time Normal 5 [ns] - High Speed 2 [ns] - 14 [ns] Todly Output Delay Time Normal 0 [ns] - 14 [ns] High Speed - - 14 [ns] Toh Output Hold Time High Speed 2.5 [ns] - 3-5. Current consumption TX mode Standard Data rate VDD33 [mA] VIO [mA] Typ. Max. Typ. Max. 802.11b 11Mbps 160 185 135 - 802.11g 54Mbps 115 135 135 - 802.11n HT20 MCS7 110 135 135 - 802.11n HT40 MCS7 97 120 135 - RX mode Standard Data rate VDD33 [mA] VIO [mA] Typ. Max. Typ. Max. 802.11b 11Mbps 42 50 135 - 802.11g 54Mbps 42 50 135 - 802.11n HT20 MCS7 42 50 135 - 802.11n HT40 MCS7 42 50 135 -

3-6. Receiver characteristics 1) Minimum Receiver Sensitivity Standard Data rate Min.[dBm] Typ.[dBm] Max.[dBm] PER[%] 802.11b 1 Mbps - -95 -80 8 2 Mbps - -93 -80 8 5.5 bps - -89 -76 8 11 Mbps - -86 -76 8 802.11b 6 Mbps - -89 -82 10 9 Mbps - -88 -81 10 12 Mbps - -86 -79 10 18 Mbps - -84 -77 10 24 Mbps - -81 -74 10 36 Mbps - -80 -70 10 48 Mbps - -74 -66 10 54 Mbps - -72 -65 10 802.11n MCS0 - -88 -82 10 HT20 MCS1 - -85 -79 10 MCS2 - -83 -77 10 MCS3 - -81 -74 10 MCS4 - -77 -70 10 MCS5 - -73 -66 10 MCS6 - -71 -65 10 MCS7 - -69 -64 10 802.11n MCS0 - -87 -79 10 HT40 MCS1 - -84 -76 10 MCS2 - -82 -74 10 MCS3 - -80 -71 10 MCS4 - -76 -67 10 MCS5 - -72 -53 10 MCS6 - -69 -62 10 MCS7 - -67 -61 10 2）Maximum Receiver Sensitivity Standard Data rate Min.[dBm] Typ.[dBm] Max.[dBm] PER[%] 802.11b 1M,2M -4 - - 8 5.5M,11M -10 - - 10 802.11g 6M to 54M -20 - - 10 802.11n HT20 MCS0 to 7 -20 - - 10 802.11n HT40 MCS0 to 7 -30 - - 10

3-7. Transmitter characteristics 1)Output Target Power Levels The difference of the output is within ±2.5dB. Output level, will be defined at the antenna feed point. 1)-1 2.4GHz Band 11b (DSSS) Ch Freq.[MHz] Target Power [dBm] 1M 2M 5.5M 11M 1 2412 13.5 13.5 13.5 13.5 2 2417 13.5 13.5 13.5 13.5 3 2422 13.5 13.5 13.5 13.5 4 2427 13.5 13.5 13.5 13.5 5 2432 13.5 13.5 13.5 13.5 6 2437 13.5 13.5 13.5 13.5 7 2442 13.5 13.5 13.5 13.5 8 2447 13.5 13.5 13.5 13.5 9 2452 13.5 13.5 13.5 13.5 10 2457 13.5 13.5 13.5 13.5 11 2462 13.5 13.5 13.5 13.5 12 2467 13.5 13.5 13.5 13.5 13 2472 13.5 13.5 13.5 13.5 11g (OFDM) Ch Freq.[MHz] Target Power [dBm] 6M 9M 12M 18M 24M 36M 48M 56M 1 2412 12 12 12 12 12 12 12 12 2 2417 12 12 12 12 12 12 12 12 3 2422 12 12 12 12 12 12 12 12 4 2427 12 12 12 12 12 12 12 12 5 2432 12 12 12 12 12 12 12 12 6 2437 12 12 12 12 12 12 12 12 7 2442 12 12 12 12 12 12 12 12 8 2447 12 12 12 12 12 12 12 12 9 2452 12 12 12 12 12 12 12 12 10 2457 12 12 12 12 12 12 12 12 11 2462 12 12 12 12 12 12 12 12 12 2467 12 12 12 12 12 12 12 12 13 2472 12 12 12 12 12 12 12 12

11n /HT20(OFDM) 11n /HT20(OFDM) Ch Ch Freq. Target Power [dBm] (HT20) (HT40) [MHz] MCS0 MCS1 MCS2 MCS3 MCS4 MCS5 MCS6 MCS7 1 - 2412 12 12 12 12 12 12 12 12 2 - 2417 12 12 12 12 12 12 12 12 3 1 2422 12 12 12 12 12 12 12 12 4 2 2427 12 12 12 12 12 12 12 12 5 3 2432 12 12 12 12 12 12 12 12 6 4 2437 12 12 12 12 12 12 12 12 7 5 2442 12 12 12 12 12 12 12 12 8 6 2447 12 12 12 12 12 12 12 12 9 7 2452 12 12 12 12 12 12 12 12 10 - 2457 12 12 12 12 12 12 12 12 11 - 2462 12 12 12 12 12 12 12 12 12 - 2467 12 12 12 12 12 12 12 12 13 - 2472 12 12 12 12 12 12 12 12 2)EVM ITEM rate EVM [%] 11b 1 Mbps 35 11b 2 Mbps 35 11b 5.5 Mbps 35 11b 11 Mbps 35 11b 6 Mbps 56.2 11g 9 Mbps 39.8 11g 12 Mbps 31.6 11g 18 Mbps 22.4 11g 24 Mbps 15.8 11g 36 Mbps 11.2 11g 48 Mbps 7.9 11g 54 mBps 5.6 11n HT20/HT40 MCS0 56.2 11n HT20/HT40 MCS1 31.6 11n HT20/HT40 MCS2 22.4 11n HT20/HT40 MCS3 15.8 11n HT20/HT40 MCS4 11.2 11n HT20/HT40 MCS5 7.9 11n HT20/HT40 MCS6 5.6 11n HT20/HT40 MCS7 4.0

3)Spectrum Mask Mask [dBr] DS 0MHz to +/-11MHz 0 DS f+/-11MHz to 22MHz -28 DS f+/-22MHz -50 OFDM 0MHz to +/-9MHz 0 OFDM f+/-11MHz -20 OFDM f+/-20MHz -28 OFDM f+/-30MHz -40 HT20 0MHz to +/-9MHz 0 HT20 f+/-11MHz -20 HT20 f+/-20MHz -28 HT20 f+/-30MHz -45 HT40 0MHz to +/-9MHz 0 HT40 f+/-11MHz -20 HT40 f+/-20MHz -28 HT40 f+/-30MHz -45 4)Frequency Accuracy +/- 20 ppm 4.Mechanical Specifications 4-1. Dimension : 9.0mm×19.5mm, t= 1.6mm MAX 4-2. Weight : Typical 0.5g 4-3. Terminal number and name No. Name Type Function 1 Pdn IN Power on reset 2 VIO POWER I/F power supply 3 SD_CMD IO SDIO command 4 SD_D0 IO SDIO data 0 5 SD_D1 IO SDIO data 1 6 GND GND GND 7 SD_CLK IO SDIO clock 8 GND GND GND 9 SD_D3 IO SDIO data 3 10 SD_D2 IO SDIO data 2 11 GND GND GND 12 VDD33 POWER Main power supply 3.3V 13 VDD33 POWER Main power supply 3.3V 14 HostWakeup OUT Host Wake up

4-4. Module Overall Appearance 5.Revision REV Contents Date Name


Document Created: 2016-09-27 14:33:44
Document Modified: 2016-09-27 14:33:44
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC