FCC Report_SAR

FCC ID: W2Z-01000006

RF Exposure Info

Download: PDF
FCCID_2473654

Test report No. : 103188948—C Page : 1 of 88 Issued date : October 9, 2014 Revised date : December 12, 2014 (—r04) FCC ID : W2Z—01000006 SAR TEST REPORT Test Report No.: 103188948—C Applicant : FUJIFILM Corporation Type of Equipment _: Flat Panel Sensor Model No. : DR—ID12018SE (*. with built—in wireless LAN module) FCC ID W27—01000006 Test Standard : _FCC 47CFR §2.1093 Test Result : Complied Hmmu‘zd Operation Band Remarks <0.10 W/kg 2412—2472MHz |(DTS) Antenna#{0, 2417MHz, 1 1n(@2OHT)(MCSO), Outputpower: 15.00dBm, Measured SAR(1g)=0.022Whkz. 0.17 W/kg _|__5180—5320MHz |(UNI) Antenna#0, 5260MHz, 1 1a (6Mbps), Outputpower: 13.29dBm, Measured SAR(1g)—0.113Whke. 0.20 W/kg _|__5500—5700MHz |(UNI) Antenna#/0, 5680MHz, 1 1a (6Mbps), Outputpower: 16.01dBm, Measured SAR(1g)=0.14W/kzg. 0.20 W/kg _|__5745—5825MHz |(UNI) Antenna#/0, 5745MHz, 1 1a (6Mbps), Outputpower: 16.18dBm, Measured SAR(1g)—0.134Whkzg. *. exposure Co—location was not considered, because the SLLSR (SAR to peak location separation ratio) was smaller than 0.04. This test report shall not be reproduced in full or partial, without the written approval of UL Japan, Inc. m is 3 J t The results in this report apply only to the sample tested. This sample tested is in compliance with the limits ofthe above regulation. The test results in this test report are traceable to the national or international standards. This test report must not be used by the customer to claim product certification, approval, or endorsement by any agency of the Federal Government. The opinions and the interpretations to the result of the description in this report are outside scopes where UL Japan has S been accredited. Date of test: September 8—12 and16, 2014 Test engineer: I Danfos Hiroshi Naka Engineer, Consumer Technology Division Approved by: /Z/W Toyokazu Imamura Leader, Consumer Technology Division \\‘\\”P'l“ v X WA o $lmnm /‘ «: \_./ -;' w rC i femlin®waed D The testing in which "Non—accreditation"is displayed is outside the accreditation scopes in UL Japan. Tw JAB *L hh ‘\\\\\‘ Testing @ There is no testing item of "Non—accreditation‘". RTLO2610 UL Japan, Inc. Shonan EMC Lab. 13—EM—FO429 1—22—3 Megumigaoka, Hiratsuka—shi, Kanagawa—ken, 259—1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401

Test report No. : 10318894S-C Page : 2 of 88 Issued date : October 9, 2014 Revised date : December 12, 2014 (-r04) FCC ID : W2Z-01000006 REVISION HISTORY Revision Test report No. Date Page revised Contents Original 10318894S-C October 9, 2014 - - -r01 10318894S-C December 2, 2014 p1,2,6, w58 band: DTS->UNII. -r02 10318894S-C December 10, 2014 p1,2,3, Operation temperature range is deleted. p6,16,17 Correction of erroneous description. -r03 10318894S-C December 12, 2014 P6,16 Operation temperature range is deleted. Correction of erroneous description. -r04 10318894S-C December 12, 2014 P17 Operation temperature range is deleted. Correction of erroneous description. *. By issue of new revision report, the report of an old revision becomes invalid. CONTENTS PAGE REVISION HISTORY................................................................................................................................................... 2 CONTENTS .................................................................................................................................................... 2 SECTION 1: Customer information .................................................................................... 3 SECTION 2: Equipment under test (EUT) ......................................................................... 3 2.1 Identification of EUT .......................................................................................................... 3 2.2 Product Description (Wireless LAN module, antenna) ....................................................... 3 2.3 Tx output power (typical) specification (antenna port terminal conducted) ........................ 4 2.4 Maximum output power which may possible ...................................................................... 5 SECTION 3: Test specification, procedures and results .................................................... 6 3.1 Test specification ................................................................................................................. 6 3.2 Exposure limit ..................................................................................................................... 6 3.3 Procedure and result ............................................................................................................ 6 3.4 Test location ........................................................................................................................ 6 3.5 Confirmation before SAR testing ........................................................................................ 7 3.6 Confirmation after SAR testing ........................................................................................... 7 3.7 Test setup of EUT and SAR measurement procedure ......................................................... 8 SECTION 4: Operation of EUT during SAR testing ......................................................... 9 SECTION 5: Uncertainty assessment (SAR measurement) .............................................. 10 SECTION 6: Confirmation before testing........................................................................... 11 6.1 Assessment for the antenna terminal port conducted power of EUT ................................... 11 SECTION 7: Measurement results ...................................................................................... 16 7.1 SAR test results (Body) ....................................................................................................... 16 7.2 SAR test results (Head) ....................................................................................................... 17 Contents of appendixes APPENDIX 1: Photographs of test setup ............................................................................... 18 Appendix 1-1 Photograph of EUT and antenna position ............................................................................ 18 Appendix 1-2 Antenna position.................................................................................................................. 19 Appendix 1-3 EUT and support equipment ................................................................................................ 20 Appendix 1-4 Photograph of SAR test setup.............................................................................................. 21 APPENDIX 2: SAR Measurement data ................................................................................. 23 Appendix 2-1 Evaluation procedure ........................................................................................................... 23 Appendix 2-2 Measurement data................................................................................................................ 24 APPENDIX 3: Test instruments ............................................................................................. 40 Appendix 3-1 Equipment used ................................................................................................................... 40 Appendix 3-2 Configuration and peripherals ............................................................................................. 41 Appendix 3-3 Test system specification ..................................................................................................... 42 Appendix 3-4 Simulated tissues composition and parameter confirmation ................................................ 43 Appendix 3-5 System check results............................................................................................................ 44 Appendix 3-6 System check uncertainty .................................................................................................... 45 Appendix 3-7 System check measurement data ......................................................................................... 45 Appendix 3-8 Calibration certificate: E-Field Probe (EX3DV4) ............................................................... 50 Appendix 3-9 Calibration certificate: Dipole (D2450V2) .......................................................................... 61 Appendix 3-10 Calibration certificate: Dipole (D5GHzV2) ........................................................................ 69 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401

Test report No. : 10318894S-C Page : 3 of 88 Issued date : October 9, 2014 Revised date : December 10, 2014 (-r02) FCC ID : W2Z-01000006 SECTION 1: Customer information Company Name FUJIFILM Corporation Brand Name FUJIFILM Address 2-26-30 Nishiazabu Minatoku Tokyo 106-8620, Japan Telephone Number 81-3-6271-1975 Facsimile Number 81-3-6271-1189 Contact Person Mitsuyuki Komiya SECTION 2: Equipment under test (EUT) 2.1 Identification of EUT Type of Equipment Flat Panel Sensor Model Number DR-ID1201SE Serial Number N120002 Condition of EUT Engineering prototype (*. Not for sale. This sample is equivalent to mass-production items) Receipt Date of Sample August 4, 2014 (*. No modification by the Lab.) Country of Mass-production Japan Rating DC8V Category Identified Portable device (*. Since EUT may contact and/or very close to a human body and head during Wi-Fi operation, the partial-body SAR (1g) shall be observed.) SAR Accessary Any body-worn accessory was not applied. Model: DR-ID1201SE (referred to as the EUT in this report) is a Flat Panel Sensor with a wireless function and used in the hospitality environment. Since this EUT is the medical device, the EUT is only Feature of EUT, SAR used under the guidance of a doctor or a qualified person. The possibility of the maximum RF human tested consideration exposure is only a body/head of the patient who comes in contact directly on the front surface side (patient side) of the EUT. Therefore, the SAR test was only applied to the front surface side (patient side) of the EUT. *. DR-ID1201SE: Flat Panel Sensor has the series model: DR-ID1211SE. DR-ID1211SE is the same mechanically and electrically as DR-ID1201SE, except X ray detection component. This difference doesn't influence the characteristic of wireless LAN applications. Therefore, DR-ID1201SE was tested representatively. DR-ID1201SE DE-ID1211SE Size of panel (mm) 393.8459.816.0 393.8459.816.0 X ray detection component (scintillator) GOS (Gd2O2S:Tb, oxysulfide gadolinium) CsI (cesium iodide) 2.2 Product Description (Wireless LAN module, antenna) Equipment type Transceiver Model SX-PCEAN(FF-E) Frequency band 2.4GHz band 5GHz band 11b,g, 11a, Frequency of operation n(20HT) 2412-2462 (*.ch.1-11) n(20HT) 5180-5320 (*.ch.36-64) 5500-5700 (*.ch.100-140) 5745-5825 (*.ch.149-165) (MHz) (*.ch.: channel) n(40HT) 2422-2452 (*.ch.3-9) n(40HT) 5190-5310 (*.ch.38-62) 5510-5670 (*.ch.102-134) 5755, 5795 (*.ch.151,159) Channel spacing (MHz) 5 (11b,g,n(20HT),n(40HT)) 20 (11b,g,n(20HT)) / 40 (11n(40HT)) 20 (11b,g,n(20HT)) / 40 Bandwidth (MHz) 20 (11b,g,n(20HT)) / 40 (11n(40HT)) (11n(40HT)) DSSS: DBPSK, DQPSK, CCK (11b), Type of modulation OFDM: BPSK, QPSK, 16QAM, 64QAM (11g,a,n(20HT),n(40HT)) 11b 13.5 2.5 (*.ch.1-11, 1-11Mbps) 11a: 12.52.5 15.02.5 15.02.5 11g 17.0 2.5 (*.ch.36-64, 6-54Mbps) (*.ch.100-140, 6-48Mbps) (*.ch.149-165, 6-48Mbps) Transmit power (typical, (*.ch.2, 6-36Mbps) maximum channel and data rate) n(20HT) 14.5 2.5 n(20HT) 11.02.5 13.52.5 13.52.5 and tolerance (as manufacture (*.ch.2, MCS0-4/8-12)) (*.ch.36-64, MCS0-6/8-14) (*.ch.100-140, MCS0-4/8-12) (*.ch.149-165, MCS0-4/8-12) variation) n(40HT) 13.5 2.5 n(40HT) 11.02.5 11.02.5 11.02.5 (dBm) (*.ch.: channel) (*.ch.4, MCS0-4/8-12) (*.ch.46,54, MCS0-7/8-15) (*.ch.102-134, MCS0-5/8-13) (*.ch.151,159, MCS0-5/8-13) *. The value in a table shows the maximum power conditions of typical on each antenna. *. 3dBm is added to MIMO power. *. Refer to clause 2.3 for more detail. Refer to clause 2.4 for the maximum output power which may possible. *. The measured Tx output power (conducted) refers to section 6 in this report. Power supply DC 3.3V (*. DC3.3V is supplied from the main unit via constant voltage circuit.) UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401

Test report No. : 10318894S-C Page : 4 of 88 Issued date : October 9, 2014 FCC ID : W2Z-01000006 Antenna antenna #1 (Bottom, short edge side) antenna #0 (Side, long edge side) 2 pcs. (*. Separation distance between the antenna 1 and the antenna: 417mm ) Antenna quantity 11b,g,a: One selected Tx antenna operation. 11n(20HT),n(40HT): One selected Tx antenna operation (MCS0~7) / Two Tx antenna operation (MCS8~13) Antenna model 113Y120035A (cable length: 300mm) 113Y1200036A (cable length: 575mm) Antenna type / connector type Monopole antenna / Connector; PCB side: U.FL, Antenna side: soldered Antenna gain (max.peak) -5.1 dBi (2.4GHz), -6.9 dBi (2.4GHz) (*.excluding cable loss) -1.3 dBi (5GHz) -1.8 dBi (5GHz) *. The EUT do not use the special transmitting technique such as “beam-forming” and “time-space code diversity.” 2.3 Tx output power (typical) specification (antenna port terminal conducted) Target Power [dBm] (average) 11b 11g 11n(20HT) [MHz] CH 1 2 5.5 11 6 9 12 18 24 36 48 54 MCS0 MCS1 MCS2 MCS3 MCS4 MCS5 MCS6 MCS7 MCS8 MCS9 MCS10 MCS11 MCS12 MCS13 MCS14 MCS15 2412 1 13.5 13.5 13.5 13.5 13.5 13.5 13.5 13.5 13.5 13.5 13.5 13.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 13.5 13.5 13.5 13.5 13.5 13.5 13.5 13.5 2417 2 13.5 13.5 13.5 13.5 17 17 17 17 17 17 16 15 14.5 14.5 14.5 14.5 14.5 14 13.5 13 17.5 17.5 17.5 17.5 17.5 17 16.5 16 2422 3 13.5 13.5 13.5 13.5 16.5 16.5 16.5 16.5 16.5 16.5 15.5 15 14 14 14 14 14 13.5 13 12.5 17 17 17 17 17 16.5 16 15.5 2427 4 13.5 13.5 13.5 13.5 16.5 16.5 16.5 16.5 16.5 16.5 15.5 15 13.5 13.5 13.5 13.5 13.5 13 12.5 12 16.5 16.5 16.5 16.5 16.5 16 15.5 15 2432 5 13.5 13.5 13.5 13.5 16 16 16 16 16 16 15.5 15 13 13 13 13 13 12.5 12.5 12 16 16 16 16 16 15.5 15.5 15 2437 6 13.5 13.5 13.5 13.5 16 16 16 16 16 16 15.5 15 12.5 12.5 12.5 12.5 12.5 12 12 11.5 15.5 15.5 15.5 15.5 15.5 15 15 14.5 2442 7 13.5 13.5 13.5 13.5 15.5 15.5 15.5 15.5 15.5 15.5 15 15 12 12 12 12 12 12 11.5 11.5 15 15 15 15 15 15 14.5 14.5 2447 8 13.5 13.5 13.5 13.5 15.5 15.5 15.5 15.5 15.5 15.5 15 15 11.5 11.5 11.5 11.5 11.5 11.5 11 11 14.5 14.5 14.5 14.5 14.5 14.5 14 14 2452 9 13.5 13.5 13.5 13.5 15 15 15 15 15 15 15 15 11 11 11 11 11 11 11 11 14 14 14 14 14 14 14 14 2457 10 13.5 13.5 13.5 13.5 15 15 15 15 15 15 15 15 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 13.5 13.5 13.5 13.5 13.5 13.5 13.5 13.5 2462 11 13.5 13.5 13.5 13.5 15 15 15 15 15 15 15 15 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 13.5 13.5 13.5 13.5 13.5 13.5 13.5 13.5 Target Power [dBm] (average) 11a 11n(20HT) [MHz] CH 6 9 12 18 24 36 48 54 MCS0 MCS1 MCS2 MCS3 MCS4 MCS5 MCS6 MCS7 MCS8 MCS9 MCS10 MCS11 MCS12 MCS13 MCS14 MCS15 5180 36 12.5 12.5 12.5 12.5 12.5 12.5 12.5 12.5 11 11 11 11 11 11 11 10.5 14 14 14 14 14 14 14 13.5 5200 40 12.5 12.5 12.5 12.5 12.5 12.5 12.5 12.5 11 11 11 11 11 11 11 10.5 14 14 14 14 14 14 14 13.5 5220 44 12.5 12.5 12.5 12.5 12.5 12.5 12.5 12.5 11 11 11 11 11 11 11 10.5 14 14 14 14 14 14 14 13.5 5240 48 12.5 12.5 12.5 12.5 12.5 12.5 12.5 12.5 11 11 11 11 11 11 11 10.5 14 14 14 14 14 14 14 13.5 5260 52 12.5 12.5 12.5 12.5 12.5 12.5 12.5 12.5 11 11 11 11 11 11 11 10.5 14 14 14 14 14 14 14 13.5 5280 56 12.5 12.5 12.5 12.5 12.5 12.5 12.5 12.5 11 11 11 11 11 11 11 10.5 14 14 14 14 14 14 14 13.5 5300 60 12.5 12.5 12.5 12.5 12.5 12.5 12.5 12.5 11 11 11 11 11 11 11 10.5 14 14 14 14 14 14 14 13.5 5320 64 12.5 12.5 12.5 12.5 12.5 12.5 12.5 12.5 11 11 11 11 11 11 11 10.5 14 14 14 14 14 14 14 13.5 5500 100 15 15 15 15 15 15 15 14 13.5 13.5 13.5 13.5 13.5 12.5 10.5 8.5 16.5 16.5 16.5 16.5 16.5 15.5 13.5 11.5 5520 104 15 15 15 15 15 15 15 14 13.5 13.5 13.5 13.5 13.5 12.5 10.5 8.5 16.5 16.5 16.5 16.5 16.5 15.5 13.5 11.5 5540 108 15 15 15 15 15 15 15 14 13.5 13.5 13.5 13.5 13.5 12.5 10.5 8.5 16.5 16.5 16.5 16.5 16.5 15.5 13.5 11.5 5560 112 15 15 15 15 15 15 15 14 13.5 13.5 13.5 13.5 13.5 12.5 10.5 8.5 16.5 16.5 16.5 16.5 16.5 15.5 13.5 11.5 5580 116 15 15 15 15 15 15 15 14 13.5 13.5 13.5 13.5 13.5 12.5 10.5 8.5 16.5 16.5 16.5 16.5 16.5 15.5 13.5 11.5 5600 120 15 15 15 15 15 15 15 14 13.5 13.5 13.5 13.5 13.5 12.5 10.5 8.5 16.5 16.5 16.5 16.5 16.5 15.5 13.5 11.5 5620 124 15 15 15 15 15 15 15 14 13.5 13.5 13.5 13.5 13.5 12.5 10.5 8.5 16.5 16.5 16.5 16.5 16.5 15.5 13.5 11.5 5640 128 15 15 15 15 15 15 15 14 13.5 13.5 13.5 13.5 13.5 12.5 10.5 8.5 16.5 16.5 16.5 16.5 16.5 15.5 13.5 11.5 5660 132 15 15 15 15 15 15 15 14 13.5 13.5 13.5 13.5 13.5 12.5 10.5 8.5 16.5 16.5 16.5 16.5 16.5 15.5 13.5 11.5 5680 136 15 15 15 15 15 15 15 14 13.5 13.5 13.5 13.5 13.5 12.5 10.5 8.5 16.5 16.5 16.5 16.5 16.5 15.5 13.5 11.5 5700 140 15 15 15 15 15 15 15 14 13.5 13.5 13.5 13.5 13.5 12.5 10.5 8.5 16.5 16.5 16.5 16.5 16.5 15.5 13.5 11.5 5745 149 15 15 15 15 15 15 15 14 13.5 13.5 13.5 13.5 13.5 12.5 10.5 8.5 16.5 16.5 16.5 16.5 16.5 15.5 13.5 11.5 5765 153 15 15 15 15 15 15 15 14 13.5 13.5 13.5 13.5 13.5 12.5 10.5 8.5 16.5 16.5 16.5 16.5 16.5 15.5 13.5 11.5 5785 157 15 15 15 15 15 15 15 14 13.5 13.5 13.5 13.5 13.5 12.5 10.5 8.5 16.5 16.5 16.5 16.5 16.5 15.5 13.5 11.5 5805 161 15 15 15 15 15 15 15 14 13.5 13.5 13.5 13.5 13.5 12.5 10.5 8.5 16.5 16.5 16.5 16.5 16.5 15.5 13.5 11.5 5825 165 15 15 15 15 15 15 15 14 13.5 13.5 13.5 13.5 13.5 12.5 10.5 8.5 16.5 16.5 16.5 16.5 16.5 15.5 13.5 11.5 Target Power [dBm] (average) 11n(40HT) [MHz] CH MCS0 MCS1 MCS2 MCS3 MCS4 MCS5 MCS6 MCS7 MCS8 MCS9 MCS10 MCS11 MCS12 MCS13 MCS14 MCS15 2422 3 6 6 6 6 6 6 6 6 9 9 9 9 9 9 9 9 2427 4 13.5 13.5 13.5 13.5 13.5 13 12.5 12 16.5 16.5 16.5 16.5 16.5 16 15.5 15 2432 5 12 12 12 12 12 11 11 11 15 15 15 15 15 14 14 14 2437 6 10.5 10.5 10.5 10.5 10.5 10.5 10 10 13.5 13.5 13.5 13.5 13.5 13.5 13 13 2442 7 9.5 9.5 9.5 9.5 9.5 9 9 9 12.5 12.5 12.5 12.5 12.5 12 12 12 2447 8 8 8 8 8 8 8 8 8 11 11 11 11 11 11 11 11 2452 9 7 7 7 7 7 7 7 7 10 10 10 10 10 10 10 10 5190 38 10 10 10 10 10 10 10 10 13 13 13 13 13 13 13 13 5230 46 11 11 11 11 11 11 11 11 14 14 14 14 14 14 14 14 5270 54 11 11 11 11 11 11 11 11 14 14 14 14 14 14 14 14 5310 62 10 10 10 10 10 10 10 10 13 13 13 13 13 13 13 13 5510 102 11 11 11 11 11 11 10 8 14 14 14 14 14 14 13 11 5550 110 11 11 11 11 11 11 10 8 14 14 14 14 14 14 13 11 5590 118 11 11 11 11 11 11 10 8 14 14 14 14 14 14 13 11 5630 126 11 11 11 11 11 11 10 8 14 14 14 14 14 14 13 11 5670 134 11 11 11 11 11 11 10 8 14 14 14 14 14 14 13 11 5755 151 11 11 11 11 11 11 10 8 14 14 14 14 14 14 13 11 5795 159 11 11 11 11 11 11 10 8 14 14 14 14 14 14 13 11 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401

Test report No. : 10318894S-C Page : 5 of 88 Issued date : October 9, 2014 FCC ID : W2Z-01000006 2.4. Maximum output power which may possible Maximum output power which may possible [dBm] (average) 11b 11g 11n(20HT) [MHz] CH 1 2 5.5 11 6 9 12 18 24 36 48 54 MCS0 MCS1 MCS2 MCS3 MCS4 MCS5 MCS6 MCS7 MCS8 MCS9 MCS10 MCS11 MCS12 MCS13 MCS14 MCS15 2412 1 16 16 16 16 16 16 16 16 16 16 16 16 13 13 13 13 13 13 13 13 16 16 16 16 16 16 16 16 2417 2 16 16 16 16 19.5 19.5 19.5 19.5 19.5 19.5 18.5 17.5 17 17 17 17 17 16.5 16 15.5 20 20 20 20 20 19.5 19 18.5 2422 3 16 16 16 16 19 19 19 19 19 19 18 17.5 16.5 16.5 16.5 16.5 16.5 16 15.5 15 19.5 19.5 19.5 19.5 19.5 19 18.5 18 2427 4 16 16 16 16 19 19 19 19 19 19 18 17.5 16 16 16 16 16 15.5 15 14.5 19 19 19 19 19 18.5 18 17.5 2432 5 16 16 16 16 18.5 18.5 18.5 18.5 18.5 18.5 18 17.5 15.5 15.5 15.5 15.5 15.5 15 15 14.5 18.5 18.5 18.5 18.5 18.5 18 18 17.5 2437 6 16 16 16 16 18.5 18.5 18.5 18.5 18.5 18.5 18 17.5 15 15 15 15 15 14.5 14.5 14 18 18 18 18 18 17.5 17.5 17 2442 7 16 16 16 16 18 18 18 18 18 18 17.5 17.5 14.5 14.5 14.5 14.5 14.5 14.5 14 14 17.5 17.5 17.5 17.5 17.5 17.5 17 17 2447 8 16 16 16 16 18 18 18 18 18 18 17.5 17.5 14 14 14 14 14 14 13.5 13.5 17 17 17 17 17 17 16.5 16.5 2452 9 16 16 16 16 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 13.5 13.5 13.5 13.5 13.5 13.5 13.5 13.5 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16.5 2457 10 16 16 16 16 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 13 13 13 13 13 13 13 13 16 16 16 16 16 16 16 16 2462 11 16 16 16 16 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 13 13 13 13 13 13 13 13 16 16 16 16 16 16 16 16 Maximum output power which may possible [dBm] (average) 11a 11n(20HT) [MHz] CH 6 9 12 18 24 36 48 54 MCS0 MCS1 MCS2 MCS3 MCS4 MCS5 MCS6 MCS7 MCS8 MCS9 MCS10 MCS11 MCS12 MCS13 MCS14 MCS15 5180 36 15 15 15 15 15 15 15 15 13.5 13.5 13.5 13.5 13.5 13.5 13.5 13 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16 5200 40 15 15 15 15 15 15 15 15 13.5 13.5 13.5 13.5 13.5 13.5 13.5 13 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16 5220 44 15 15 15 15 15 15 15 15 13.5 13.5 13.5 13.5 13.5 13.5 13.5 13 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16 5240 48 15 15 15 15 15 15 15 15 13.5 13.5 13.5 13.5 13.5 13.5 13.5 13 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16 5260 52 15 15 15 15 15 15 15 15 13.5 13.5 13.5 13.5 13.5 13.5 13.5 13 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16 5280 56 15 15 15 15 15 15 15 15 13.5 13.5 13.5 13.5 13.5 13.5 13.5 13 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16 5300 60 15 15 15 15 15 15 15 15 13.5 13.5 13.5 13.5 13.5 13.5 13.5 13 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16 5320 64 15 15 15 15 15 15 15 15 13.5 13.5 13.5 13.5 13.5 13.5 13.5 13 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16 5500 100 17.5 17.5 17.5 17.5 17.5 17.5 17.5 16.5 16 16 16 16 16 15 13 11 19 19 19 19 19 18 16 14 5520 104 17.5 17.5 17.5 17.5 17.5 17.5 17.5 16.5 16 16 16 16 16 15 13 11 19 19 19 19 19 18 16 14 5540 108 17.5 17.5 17.5 17.5 17.5 17.5 17.5 16.5 16 16 16 16 16 15 13 11 19 19 19 19 19 18 16 14 5560 112 17.5 17.5 17.5 17.5 17.5 17.5 17.5 16.5 16 16 16 16 16 15 13 11 19 19 19 19 19 18 16 14 5580 116 17.5 17.5 17.5 17.5 17.5 17.5 17.5 16.5 16 16 16 16 16 15 13 11 19 19 19 19 19 18 16 14 5600 120 17.5 17.5 17.5 17.5 17.5 17.5 17.5 16.5 16 16 16 16 16 15 13 11 19 19 19 19 19 18 16 14 5620 124 17.5 17.5 17.5 17.5 17.5 17.5 17.5 16.5 16 16 16 16 16 15 13 11 19 19 19 19 19 18 16 14 5640 128 17.5 17.5 17.5 17.5 17.5 17.5 17.5 16.5 16 16 16 16 16 15 13 11 19 19 19 19 19 18 16 14 5660 132 17.5 17.5 17.5 17.5 17.5 17.5 17.5 16.5 16 16 16 16 16 15 13 11 19 19 19 19 19 18 16 14 5680 136 17.5 17.5 17.5 17.5 17.5 17.5 17.5 16.5 16 16 16 16 16 15 13 11 19 19 19 19 19 18 16 14 5700 140 17.5 17.5 17.5 17.5 17.5 17.5 17.5 16.5 16 16 16 16 16 15 13 11 19 19 19 19 19 18 16 14 5745 149 17.5 17.5 17.5 17.5 17.5 17.5 17.5 16.5 16 16 16 16 16 15 13 11 19 19 19 19 19 18 16 14 5765 153 17.5 17.5 17.5 17.5 17.5 17.5 17.5 16.5 16 16 16 16 16 15 13 11 19 19 19 19 19 18 16 14 5785 157 17.5 17.5 17.5 17.5 17.5 17.5 17.5 16.5 16 16 16 16 16 15 13 11 19 19 19 19 19 18 16 14 5805 161 17.5 17.5 17.5 17.5 17.5 17.5 17.5 16.5 16 16 16 16 16 15 13 11 19 19 19 19 19 18 16 14 5825 165 17.5 17.5 17.5 17.5 17.5 17.5 17.5 16.5 16 16 16 16 16 15 13 11 19 19 19 19 19 18 16 14 Maximum output power which may possible [dBm] (average) 11n(40HT) [MHz] CH MCS0 MCS1 MCS2 MCS3 MCS4 MCS5 MCS6 MCS7 MCS8 MCS9 MCS10 MCS11 MCS12 MCS13 MCS14 MCS15 2422 3 8.5 8.5 8.5 8.5 8.5 8.5 8.5 8.5 11.5 11.5 11.5 11.5 11.5 11.5 11.5 11.5 2427 4 16 16 16 16 16 15.5 15 14.5 19 19 19 19 19 18.5 18 17.5 2432 5 14.5 14.5 14.5 14.5 14.5 13.5 13.5 13.5 17.5 17.5 17.5 17.5 17.5 16.5 16.5 16.5 2437 6 13 13 13 13 13 13 12.5 12.5 16 16 16 16 16 16 15.5 15.5 2442 7 12 12 12 12 12 11.5 11.5 11.5 15 15 15 15 15 14.5 14.5 14.5 2447 8 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 13.5 13.5 13.5 13.5 13.5 13.5 13.5 13.5 2452 9 9.5 9.5 9.5 9.5 9.5 9.5 9.5 9.5 12.5 12.5 12.5 12.5 12.5 12.5 12.5 12.5 5190 38 12.5 12.5 12.5 12.5 12.5 12.5 12.5 12.5 15.5 15.5 15.5 15.5 15.5 15.5 15.5 15.5 5230 46 13.5 13.5 13.5 13.5 13.5 13.5 13.5 13.5 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16.5 5270 54 13.5 13.5 13.5 13.5 13.5 13.5 13.5 13.5 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16.5 5310 62 12.5 12.5 12.5 12.5 12.5 12.5 12.5 12.5 15.5 15.5 15.5 15.5 15.5 15.5 15.5 15.5 5510 102 13.5 13.5 13.5 13.5 13.5 13.5 12.5 10.5 16.5 16.5 16.5 16.5 16.5 16.5 15.5 13.5 5550 110 13.5 13.5 13.5 13.5 13.5 13.5 12.5 10.5 16.5 16.5 16.5 16.5 16.5 16.5 15.5 13.5 5590 118 13.5 13.5 13.5 13.5 13.5 13.5 12.5 10.5 16.5 16.5 16.5 16.5 16.5 16.5 15.5 13.5 5630 126 13.5 13.5 13.5 13.5 13.5 13.5 12.5 10.5 16.5 16.5 16.5 16.5 16.5 16.5 15.5 13.5 5670 134 13.5 13.5 13.5 13.5 13.5 13.5 12.5 10.5 16.5 16.5 16.5 16.5 16.5 16.5 15.5 13.5 5755 151 13.5 13.5 13.5 13.5 13.5 13.5 12.5 10.5 16.5 16.5 16.5 16.5 16.5 16.5 15.5 13.5 5795 159 13.5 13.5 13.5 13.5 13.5 13.5 12.5 10.5 16.5 16.5 16.5 16.5 16.5 16.5 15.5 13.5 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401

Test report No. : 10318894S-C Page : 6 of 88 Issued date : October 9, 2014 Revised date : December 12, 2014 (-r03) FCC ID : W2Z-01000006 SECTION 3: Test specification, procedures and results 3.1 Test specification The US Federal Communications Commission has released the report and order “Guidelines for Evaluating the Environmental Effects of RF Radiation", ET Docket No. 93-62 in August 1996. The order requires routine SAR evaluation prior to equipment authorization of portable transmitter devices, including portable telephones. For consumer products, the applicable limit is 1.6 mW/g for an uncontrolled environment and 8.0 mW/g for an occupational/controlled environment as recommended by the ANSI/IEEE standard C95.1-1992. The device should be evaluated at maximum output power (radiated from the antenna) under “worst-case” conditions for normal or intended use, incorporating normal antenna operating positions, device peak performance frequencies and positions for maximum RF energy coupling in accordance with the following measurement procedures.. KDB 447498 D01 (v05r02): General RF exposure guidance KDB 248227 D01 (v01r02): SAR Measurement Procedures for 802.11a/b/g Transmitters KDB 865664 D01 (v01r03): SAR measurement 100MHz to 6GHz IEEE Std. 1528-2003: IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques IEEE Std. 1528-2013: IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques. (*. The reference for Uncertainty in SAR correction for deviations in permittivity and conductivity, in clause E.3.2.) 3.2 Exposure limit Environments of exposure limit Whole-Body Partial-Body Hands, Wrists, Feet and Ankles (averaged over the entire body) (averaged over any 1g of tissue) (averaged over any 10g of tissue) (A) Limits for Occupational /Controlled Exposure (W/kg) 0.4 8.0 20.0 (B) Limits for General population /Uncontrolled Exposure (W/kg) 0.08 1.6 4.0 *. Occupational/Controlled Environments: are defined as locations where there is exposure that may be incurred by people who are aware of the potential for exposure, (i.e. as a result of employment or occupation). *. General Population/Uncontrolled Environments: are defined as locations where there is the exposure of individuals who have no knowledge or control of their exposure. The limit applied in this test report is; General population / uncontrolled exposure, Partial-Body (averaged over any 1g of tissue) limit: 1.6 W/kg 3.3 Procedures and Results Wi-Fi (DTS) Wi-Fi (UNII) Wi-Fi (UNII) Wi-Fi (UNII) (2412-2462MHz) (5180-5320MHz) (5500-5700MHz) (5745-5825MHz) Test Procedure SAR measurement; KDB 447498, KDB 248227, KDB 865664, IEEE Std.1528 Category FCC 47CFR §2.1093 Results (SAR(1g)) Complied Complied Complied Complied Antenna ant#0 ant#1 ant#0 ant#1 ant#0 ant#1 ant#0 ant#1 Liquid type Body liquid Reported SAR value (*. Scaled) 0.04 W/kg 0.03 W/kg 0.17 W/kg 0.13 W/kg 0.20 W/kg 0.16 W/kg 0.20 W/kg 0.14 W/kg Measured SAR value 0.021 W/kg 0.022W/kg 0.113 W/kg 0.098 W/kg 0.14 W/kg 0.128 W/kg 0.134 W/kg 0.10 W/kg Operation mode, n20, MCS0, n20, MCS0, 11a, 6Mbps, 11a, 6Mbps, 11a, 6Mbps, 11a, 6Mbps, 11a, 6Mbps, 11a, 6Mbps, frequency[MHz] (ch.) 2417 (2ch) 2417 (2ch) 5260 (52ch) 5300 (60ch) 5680 (136ch) 5680 (136ch) 5805 (161ch) 5745 (149ch) Output power 15.00dBm 15.76dBm 13.29dBm 13.94dBm 16.01dBm 16.53dBm 15.73dBm 16.19dBm (max. power[dBm], scaled factor) (17.0, 1.58) (17.0, 1.33) (15.0, 1.48) (15.0, 1.28) (17.5, 1.41) (17.5, 1.25) (17.5, 1.50) (17.5, 1.35) Liquid type Head liquid (by Flat phantom) Reported SAR value (*. Scaled) 0.03 W/kg 0.03 W/kg 0.08 W/kg 0.07 W/kg 0.10 W/kg 0.09 W/kg 0.11 W/kg 0.09 W/kg Measured SAR value 0.018 W/kg 0.018W/kg 0.057 W/kg 0.058 W/kg 0.071 W/kg 0.075 W/kg 0.071 W/kg 0. 063W/kg Operation mode, n20, MCS0, 11g, 6Mbps, 11a, 6Mbps, 11a, 6Mbps, 11a, 6Mbps, 11a, 6Mbps, 11a, 6Mbps, 11a, 6Mbps, frequency[MHz] (ch.) 2417 (2ch) 2417 (2ch) 5260 (52ch) 5300 (60ch) 5680 (136ch) 5680 (136ch) 5805 (161ch) 5745 (149ch) Output power 15.00dBm 18.08dBm 13.62dBm 13.94dBm 16.01dBm 16.53dBm 15.73dBm 16.19dBm (max. power[dBm], scaled factor) (17.0, 1.58) (19.5, 1.39) (15.0, 1.37) (15.0, 1.28) (17.5, 1.41) (17.5, 1.25) (17.5, 1.50) (17.5, 1.35) Note: UL Japan’s SAR Work Procedures No.13-EM-W0429 and 13-EM-W0430. No addition, deviation nor exclusion has been made from standards 3.4 Test Location No.7 shielded room (2.76m (Width)  3.76m (Depth)  2.4m (Height)) for SAR testing. UL Japan, Inc., Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken 259-1220 JAPAN Telephone number: +81 463 50 6400 / Facsimile number: +81 463 50 6401 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401

Test report No. : 10318894S-C Page : 7 of 88 Issued date : October 9, 2014 FCC ID : W2Z-01000006 3.5 Confirmation before SAR testing 3.5.1 Average power for SAR test Before SAR test, the RF wiring for the sample had been switched to the antenna conducted power measurement line from the antenna line and the average power was measured. The result is shown in Section 6. Step.1 Data rate check The data rate check was measurement on one of the channel for 802.11b,g,a,n(20HT) and n(40HT) at each frequency band. 11b 11g 11a 11n(20HT) 11n(40HT) Mod Data Mod Data Mod Data MCS Spatial Mod MCS Spatial Mod MCS Spatial Mod MCS Spatial Mod (DSSS) rate (OFDM) rate (OFDM) rate Index Stream (OFDM) Index Stream (OFDM) Index Stream (OFDM) Index Stream (OFDM) DBPSK 1 Mbps BPSK 6 Mbps BPSK 6 Mbps MCS0 1 BPSK MCS8 2 BPSK MCS0 1 BPSK MCS8 2 BPSK DQPSK 2 Mbps BPSK 9 Mbps BPSK 9 Mbps MCS1 1 QPSK MCS9 2 QPSK MCS1 1 QPSK MCS9 2 QPSK CCK 5.5 Mbps QPSK 12 Mbps QPSK 12 Mbps MCS2 1 QPSK MCS10 2 QPSK MCS2 1 QPSK MCS10 2 QPSK CCK 11 Mbps QPSK 18 Mbps QPSK 18 Mbps MCS3 1 16QAM MCS11 2 16QAM MCS3 1 16QAM MCS11 2 16QAM *.Mod; Modulation 16QAM 24 Mbps 16QAM 24 Mbps MCS4 1 16QAM MCS12 2 16QAM MCS4 1 16QAM MCS12 2 16QAM 16QAM 36 Mbps 16QAM 36 Mbps MCS5 1 64QAM MCS13 2 64QAM MCS5 1 64QAM MCS13 2 64QAM 64QAM 48 Mbps 64QAM 48 Mbps MCS6 1 64QAM MCS14 2 64QAM MCS6 1 64QAM MCS14 2 64QAM 64QAM 54 Mbps 64QAM 54 Mbps MCS7 1 64QAM MCS15 2 64QAM MCS7 1 64QAM MCS15 2 64QAM *. The average power related with the data rate was measured on one of the channel for 802.11b/g/a/n(20HT)/n(40HT) modes. Step.2 Decision of SAR test channel The following operation mode, data rate and channels were determined by the SAR reference power measured. (Refer to Section 6.) (default: KDB248227->) default SAR tested channel (1Tx) SAR tested channel (2Tx) Mode MHz Channel b/g/n(20HT) b g n(20HT) n(40HT) n(20HT) n(40HT) Remarks (KDB248227) 2412 1 √ # (ant.#0,#1) n/a (*1) n/a (*1) - n/a (*4) - *1. Since the extrapolated 11 2417 2 # (ant.#0,#1) # (ant.#0,#1) (2427MHz) #(ant.#0,#1) n/a (*4) (2422MHz) n/a (*4) maximum peak SAR for the b/g/n 2437 6 √ n/a (*1) n/a (*1) n/a (*1) n/a (*1) n/a (*4) n/a (*4) maximum output channel was 2462 11 √ n/a (*1) n/a (*1) n/a (*1) (2452MHz) n/a (*1) n/a (*4) (2452MHz) n/a (*4) 1.6W/kg and the 1g averaged Mode MHz Channel a/n(20HT) a n(20HT) n(40HT) n(20HT) n(40HT) SAR was 0.8W/kg, the testing 5180 36 √ n/a (*1) n/a (*3) (5190MHz) n/a (*1) n/a (*4) (5190MHz) n/a (*4) for other channels were omitted. 5200 40 * - - - *2. Since the typical average 5220 44 * - - - power of n(40HT) was smaller 5240 48 √ n/a (*1) n/a (*3) (5230MHz) #(ant.#0) n/a (*4) (5230MHz) n/a (*4) than the corresponded 11a 5260 52 √ # (ant.#0) n/a (*3) (5270MHz) n/a (*1) n/a (*4) (5270MHz) n/a (*4) mode power and measured 5280 56 * - - - SAR(1g) of 11a mode was very 5300 60 * # (ant.#1) - - small, SAR test of n(40HT) was 5320 64 √ - n/a (*3) (5310MHz) n/a (*1) n/a (*4) (5310MHz) n/a (*4) only considered for the worst 5500 100 * - - (5510MHz) n/a (*2) - (5510MHz) n/a (*4) SAR antenna of 11a mode with 5520 104 √ n/a (*1) n/a (*3) n/a (*4) highest power channel. 5540 108 * - - (5550MHz) #(ant.#0) - (5550MHz) n/a (*4) 11 5560 112 * - - - *3. Since the average power of a/n 5580 116 √ n/a (*1) n/a (*3) (5590MHz) n/a (*2) n/a (*4) (5590MHz) n/a (*4) n(20HT) was smaller than the 5600 120 * - - - corresponded 11a power, SAR 5620 124 √ n/a (*1) n/a (*3) (5630MHz) n/a (*2) n/a (*4) (5630MHz) n/a (*4) test was not applied to n(20HT) 5640 128 * - - - mode. 5660 132 * - - (5670MHz) n/a (*2) - (5670MHz) n/a (*4) *4. Since SPLSR (SAR to peak 5680 136 √ # (ant.#0,#1) n/a (*3) n/a (*4) location separation ratio) was 5700 140 * - - - enough smaller than 0.04, SAR 5745 149 √ # (ant.#1) n/a (*3) (5755MHz) #(ant.#0) n/a (*4) (5755MHz) n/a (*4) test of MIMO mode was 5765 153 * - - - reduced. (KDB447498) 5785 157 √ n/a (*1) n/a (*3) (5795MHz) n/a (*2) n/a (*4) (5795MHz) n/a (*4) 5805 161 * # (ant.#0) - - 5825 165 √ n/a (*1) n/a (*3) n/a (*4) √ = “default test channels of requested by KDB248227”, n/a = SAR test was not applied, # = SAR test was applied (max. power channel). * = Possible 802.11a channels with maximum average output > the “default test channels” 3.6 Confirmation after SAR testing It was checked that the power drift [W] is within ±5% in the evaluation procedure of SAR testing. The verification of power drift during the SAR test is that DASY5 system calculates the power drift by measuring the e-filed at the same location at beginning and the end of the scan measurement for each test position. The result is shown in APPENDIX 2. *. DASY5 system calculation Power drift value[dB] =20log(Ea)/(Eb) (where, Before SAR testing: Eb[V/m] / After SAR testing: Ea[V/m]) Limit of power drift[W] = 5% Power drift limit (X) [dB] = 10log(P_drift)=10log(1.05/1)=10log(1.05)-10log(1)=0.21dB from E-filed relations with power. S=EH=E^2/=P/(4r^2) (: Space impedance)  P=(E^24r^2)/η Therefore, The correlation of power and the E-filed Power drift limit (X) dB=10log(P_drift)=10log(E_drift)^2=20log(E_drift) From the above mentioned, the calculated power drift of DASY5 system must be the less than 0.21dB. UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401

Test report No. : 10318894S-C Page : 8 of 88 Issued date : October 9, 2014 FCC ID : W2Z-01000006 3.7 Test setup of EUT and SAR measurement procedure After considering the outline of EUT, the SAR test was carried out on the following setup conditions. antenna #0 antenna #1 Explanation of EUT setup position Setup Antenna SAR Tested Antenna SAR Tested (*. Refer to Appendix 1 for test setup photographs.) distance /Reduced distance /Reduced Front The front surface (patient side) of EUT was touched to the Flat phantom. 10mm Tested (*2) 10mm Tested (*2) Back-tilt The EUT was set tilt and the back surface (operator side) which was near antenna#0 was 1.6mm Reduced (*1) (antenna#0) touched to the Flat phantom. Back-tilt The EUT was set tilt and the back surface (operator side) which was near antenna#1 was 1.6mm Reduced (*1) (antenna#1) touched to the Flat phantom. Back-flat The middle of back surface (operator side) of EUT was touched to the Flat phantom. 4mm Reduced (*1) 4mm Reduced (*1) Long side The long side edge surface (near antenna #0 side) of EUT was touched to the Flat phantom. 11mm Reduced (*1) 289mm Reduced (*1) (antenna#0) Long side The long side edge surface (opposite to antenna#0) of EUT was touched to the Flat phantom. 370mm Reduced (*1) 62mm Reduced (*1) Short side The short side edge surface (near antenna #1 side) of EUT was touched to the Flat phantom. 343mm Reduced (*1) 11mm Reduced (*1) (antenna#1) Short side The short side edge surface (opposite to antenna#1) of EUT was touched to the Flat phantom. 84mm Reduced (*1) 445m Reduced (*1) *. Antenna distance: this means the distance from the antenna inside a EUT to the outer surface of EUT form which an operator may touch. *. Size of EUT: 383.5  459.8  15 (thickness) [mm] *1. Since this EUT is the medical device, the EUT is only used under the guidance of a doctor or a qualified person. The possibility of the maximum RF human exposure is only a body/head of the patient who comes in contact directly on the front surface side (patient side) of the EUT. Therefore, the SAR test was only applied to the front surface side (patient side) of the EUT. *2. SAR test reduction consideration KDB 447498 D01 (v05) was taken into consideration as other approaches to reduce SAR test.. <Standalone SAR estimation> Minimum Max. power Estimate SAR(1g) Mode Band Position distance Upper frequency Remarks (with tune-up tolerance) (standalone) 11g 2.4GHz 2.462 GHz 19.5 dBm (89 mW) 1.86 W/kg >0.4W/kg, SAR test is required. 11a W52/53 Front 5.32 GHz 15.0 dBm (32 mW) 0.98 W/kg >0.4W/kg, SAR test is required. 10mm 11a W56 (Patient side) 5.7 GHz 17.5 dBm (56 mW) 1.78 W/kg >0.4W/kg, SAR test is required. 11a W58 5.825 GHz 17.5 dBm (56 mW) 1.80 W/kg >0.4W/kg, SAR test is required. Calculating formula: Estimate standalone SAR(1g) = [(max.power, mW) / (min.test separation distance, mm)]  [ f (GHz)] / [7.5] Parenthesis 1), Clause 4.3.1, KDB 447498 D01 (v05) gives the following formula to calculate the SAR(1g) test exclusion thresholds for 100MHz-6GHz at test separation distance 50mm. [(max.power of channel, including tune-up tolerance, mW) / (min.test separation distance, mm)]  [ f (GHz)]  3.0 (for SAR(1g))··················(formula (1)) If power is calculated from the upper formula (1); [SAR(1g) test exclusion thresholds, mW] = 3  [test separation distance, mm] / [f (GHz)]·····································································(formula (2)) Parenthesis 2), Clause 4.3.1, KDB 447498 D01 (v05) gives the following formula to calculate the SAR(1g) test exclusion thresholds for 1.5-6GHz at test separation distance >50mm. [test exclusion thresholds, mW] = [(Power allowed at numeric threshold for 50mm in formula (1))] + [(test separation distance, mm) - (50mm)]  10 ·(formula (3)) According to this formula, the calculated results in typical antenna distance of platform are shown in the following table. SAR(1g) test exclusion thresholds [mW] EUT's maximum power [mW] Upper frequency Antenna separation distance [mm] (including tune-up tolerance) in band [GHz] 5 10 25 46 47 2.462 10 (9.8dBm) 19 (12.8dBm) - - 90 (19.5dBm) 89 (19.5dBm) 5.32 7 (8.1dBm) 13 (11.1dBm) 33 (15.1dBm) - - 32 (15.0dBm) 5.7 6 (8.0dBm) 13 (11.0dBm) - 58 (17.6dBm) - 56 (17.5dBm) 5.825 6 (7.9dBm) 12 (10.9dBm) - 57 (17.6dBm) - 56 (17.5dBm) *. The measured average power of EUT was shown in Section 6: Confirmation before SAR testing. * Simultaneous transmission evaluation Parenthesis 2) and 3), Clause 4.3.2, KDB 447498 D01 (v05) gives the following formula to calculate the simultaneous transmission SAR test exclusion limit. (SPLSR: SAR to peak location separation ratio must be  0.04 for antenna pair.) Data Minimum Upper Max. power Estimate SAR(1g) ant#0<->#1 Mode Band Position SPLSR SAR test apply? rate distance frequency (with tune-up tolerance) Ant#0 Ant#1 Ant#0+#1 distance n20 MCS8 2.4GHz 2.462GHz 17.0dBm (50mW) 1.05 W/kg 1.05 W/kg 2.1 W/kg 417mm 0.0050 Front n20 MCS8W52/53 5.32GHz 13.5dBm (22mW) 0.68 W/kg 0.68 W/kg 1.36 W/kg 417mm 0.0033 Reduced, (Patient 10mm n20 MCS8 W56 5.7GHz 16.0dBm (40mW) 1.27 W/kg 1.27 W/kg 2.54 W/kg 417mm 0.0061 <0.04(SPLSR) side) n20 MCS8 W58 5.825GHz 16.0dBm (40mW) 1.29 W/kg 1.29 W/kg 2.58 W/kg 417mm 0.0062 *. Calculating formula: Estimate standalone SAR(1g) = [(max.power, mW) / (min.test separation distance, mm)]  [ f (GHz)] / [7.5] By the determined test setup shown above, the SAR test was applied in the following procedures. Step 1 Change the operation mode on each antenna independently with highest output power channel. Step 2 Repeat Step1 for other frequency band. *. During SAR test, the radiated power is always monitored by Spectrum Analyzer. UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401

Test report No. : 10318894S-C Page : 9 of 88 Issued date : October 9, 2014 FCC ID : W2Z-01000006 SECTION 4: Operation of EUT during testing 4.1 Operation mode for SAR testing This EUT has IEEE.802.11b,g,a,11n(20HT) and 11n(40HT) continuous transmitting modes. The frequency and the operation mode which carried out the SAR test are shown below. 11n(20HT) 11n(40HT) 11n(20HT) 11n(40HT) Operation mode 11b 11g 11a (1SS) (2SS) (1SS) (2SS) (1SS) (2SS) (1SS) (2SS) Tx frequency band 2412-2472MHz 2412-2462MHz W52/53: 5180-5320MHz 5190-5310MHz Bandwidth [MHz] 20 20 20 20 40 40 20 20 20 40 40 SAR Tested /Reduced? Tested Tested Tested Reduced(*4) Tested Reduced(*4) Tested Reduced(*3) Reduced(*4) Tested Reduced(*4) Tested frequency ant.#0 2412(*1) 2417(*1) 2417(*1) 2427(*1) 5260(*1) - 5230(*1) - - - - [MHz] ant.#1 2412(*1) 2417(*1) 2417(*1) 2427(*1) 5300(*1) - -(*2) Highest Modulation DBPSK BPSK BPSK - BPSK - BPSK - - BPSK - power /DSSS /OFDM /OFDM /OFDM /OFDM /OFDM condition Data rate 1Mbps 6Mbps MCS0 - MCS0 - MCS0 - - MCS0 - 11n(20HT) 11n(40HT) 11n(20HT) 11n(40HT) Operation mode 11a 11a (1SS) (2SS) (1SS) (2SS) (1SS) (2SS) (1SS) (2SS) Tx frequency band W56: 5500-5700MHz 5510-5670MHz W58: 5745-5825MHz 5755, 5795MHz Bandwidth [MHz] 20 20 20 40 40 20 20 20 40 40 SAR Tested/Reduced? Tested Reduced(*3) Reduced(*4) Tested Reduced(*4) Tested Reduced(*3) Reduced(*4) Tested Reduced(*4) Tested frequency ant.#0 5680(*1) - 5550(*1) 5805(*1) - 5755(*1) [MHz] - - - - ant.#1 5680(*1) - -(*2) 5745(*1) - -(*2) Highest Modulation BPSK - - BPSK - BPSK - - BPSK - power /OFDM /OFDM /OFDM /OFDM condition Data rate 6Mbps - - MCS0 - 6Mbps - - MCS0 - Tx Controlled software: ART v09 (Build 34) Mode: Continuous transmit mode. Tx antenna chain: Ant#0=100, Ant#0=010, Ant#0+Ant#1(MIMO)=110. Frequency: Selected the target frequency. / Data Rate: Selected the target data rate. HT40: Selected when 11n(40HT) was tested. Setting target power: The default power value was used. *. As for parameters other than the above, the initial value was used. *. SS: Spatial Stream *1. (KDB248227) Since the extrapolated maximum peak SAR for the maximum output channel was 1.6W/kg and the 1g averaged SAR was 0.8W/kg, the testing for other channels were omitted. *2. Since the typical average power of n(40HT) was smaller than the corresponded 11a mode power and measured SAR(1g) of 11a mode was very small, SAR test of n(40HT) was only considered for the worst SAR antenna of 11a mode with highest power channel. *3. (KDB248227) Since the average power of n(20HT) was smaller than the corresponded 11a power, SAR test was not applied to n(20HT) mode. *4. (KDB447498) Since SPLSR (SAR to peak location separation ratio) was enough smaller than 0.04, SAR test of MIMO mode was reduced. UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401

Test report No. : 10318894S-C Page : 10 of 88 Issued date : October 9, 2014 FCC ID : W2Z-01000006 SECTION 5: Uncertainty Assessment (SAR measurement) Uncertainty of SAR measurement (2.4-6GHz) (*.&:   5%, DAK3.5, Tx: 100% duty cycle) (v08) 1g SAR 10g SAR Combined measurement uncertainty of the measurement system (k=1) ± 13.7% ± 13.6% Expanded uncertainty (k=2) ± 27.4% ± 27.2% Uncertainty Probability ci ci ui ui Error Description (2.4-6GHz) (v08) Divisor Vi, veff Value distribution (1g) (10g) (1g) (10g) A Measurement System (DASY5) (std. uncertainty) (std. uncertainty) 1 Probe Calibration Error ±6.55 % Normal 1 1 1 ±6.55 % ±6.55 % ∞ 2 Axial isotropy Error ±4.7 % Rectangular √3 √0.5 √0.5 ±1.9 % ±1.9 % ∞ 3 Hemispherical isotropy Error ±9.6 % Rectangular √3 √0.5 √0.5 ±3.9 % ±3.9 % ∞ 4 Linearity Error ±4.7 % Rectangular √3 1 1 ±2.7 % ±2.7 % ∞ 5 Probe modulation response ±2.4 % Rectangular √3 1 1 ±1.4 % ±1.4 % ∞ 6 Sensitivity Error (detection limit) ±1.0 % Rectangular √3 1 1 ±0.6 % ±0.6 % ∞ 7 Boundary effects Error ±4.3% Rectangular √3 1 1 ±2.5 % ±2.5 % ∞ 8 Readout Electronics Error(DAE) ±0.3 % Rectangular √3 1 1 ±0.3 % ±0.3 % ∞ 9 Response Time Error ±0.8 % Normal 1 1 1 ±0.8 % ±0.8 % ∞ 10 Integration Time Error (100% duty cycle) ±0 % Rectangular √3 1 1 0% 0% ∞ 11 RF ambient conditions-noise ±3.0 % Rectangular √3 1 1 ±1.7 % ±1.7 % ∞ 12 RF ambient conditions-reflections ±3.0 % Rectangular √3 1 1 ±1.7 % ±1.7 % ∞ 13 Probe positioner mechanical tolerance ±3.3 % Rectangular √3 1 1 ±1.9 % ±1.9 % ∞ 14 Probe Positioning with respect to phantom shell ±6.7 % Rectangular √3 1 1 ±3.9 % ±3.9 % ∞ 15 Max. SAR evaluation (Post-processing) ±4.0 % Rectangular √3 1 1 ±2.3 % ±2.3 % ∞ B Test Sample Related 16 Device Holder or Positioner Tolerance ±3.6 % Normal 1 1 1 ±3.6 % ±3.6 % 5 17 Test Sample Positioning Error ±5.0 % Normal 1 1 1 ±5.0 % ±5.0 % 145 18 Power scaling ±0% Rectangular √3 1 1 ±0 % ±0 % ∞ 19 Drift of output power (measured, <0.2dB) ±2.3% Rectangular √3 1 1 ±2.9 % ±2.9 % ∞ C Phantom and Setup 20 Phantom uncertainty (shape, thickness tolerances) ±7.5 % Rectangular √3 1 1 ±4.3 % ±4.3 % ∞ 21 Algorithm for correcting SAR (e',σ: 5%) ±1.2 % Normal 1 1 0.84 ±1.2 % ±0.97 % ∞ 22 Measurement Liquid Conductivity Error (DAK3.5) ±3.0 % Normal 1 0.78 0.71 ±2.3 % ±2.1 % 7 23 Measurement Liquid Permittivity Error (DAK3.5) ±3.1 % Normal 1 0.23 0.26 ±0.7 % ±0.8 % 7 24 Liquid Conductivity-temp. uncertainty (2deg.C.) ±5.3 % Rectangular √3 0.78 0.71 ±2.4 % ±2.2 % ∞ 25 Liquid Permittivity-temp. uncertainty (2deg.C.) ±0.9 % Rectangular √3 0.23 0.26 ±0.1 % ±0.1 % ∞ Combined Standard Uncertainty ±13.7 % ±13.6 % 733 Expanded Uncertainty (k=2) ±27.4 % ±27.2 % *. Table of uncertainties are listed for ISO/IEC 17025. *. This measurement uncertainty budget is suggested by IEEE Std.1528(2013) and determined by Schmid & Partner Engineering AG (DASY5 Uncertainty Budget). Per KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz v01r01 Section 2.8.1., when the highest measured SAR(1g) within a frequency band is < 1.5W/kg, the extensive SAR measurement uncertainty analysis described in IEEE Std.1528 (2013) is not required in SAR reports submitted for equipment approval. UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401

Test report No. : 10318894S-C Page : 11 of 88 Issued date : October 9, 2014 FCC ID : W2Z-01000006 SECTION 6: Confirmation before testing 6.1 Assessment for the antenna terminal port conducted power of EUT (Worst data rate, worst channel determination) 6.1.1 2412-2462MHz Power spec. Duty Standalone: Antenna #0 (chain #0) Standalone: Antenna #1 (chain #1) MIMO Ant.#0+Ant.#1 Data Mode Freq. rate Typ. Max. factor Set Ave.   Apply Set Ave.   Apply MIMO MIMO SUM   target Meas. pwr. target Max. SAR pwr. target Max. SAR target max. Ave. target Max. Power Tune-up [MHz] [Mbps] [dBm] [dBm] [dB] [dB] [dBm] [dB] [dB] test? [dBm] [dBm] [dB] [dBm] test? [dBm] [dBm] [dBm] [dB] [dB] 2412 1 13.5 16.0 0.00 13.5 13.91 0.41 -2.09 - 13.5 13.92 0.42 -2.08 - default 2412 2 13.5 16.0 0.01 13.5 13.79 0.29 -2.21 - 13.5 13.83 0.33 -2.17 - default 2412 5.5 13.5 16.0 0.02 13.5 13.90 0.40 -2.10 - 13.5 13.89 0.39 -2.11 - default 2412 11 13.5 16.0 0.03 13.5 13.86 0.36 -2.14 - 13.5 13.87 0.37 -2.13 - default 11b 2437 1 13.5 16.0 0.00 13.5 13.44 -0.06 -2.56 - 13.5 13.55 0.05 -2.45 - default 2462 1 13.5 16.0 0.00 13.5 13.44 -0.06 -2.56 - 13.5 13.40 -0.10 -2.60 - default 2412 1 13.5 16.0 0.00 14.5 14.47 0.97 -1.53 Yes 14.5 15.17 1.67 -0.83 Yes tune-up 2437 1 13.5 16.0 0.00 14.5 14.36 0.86 -1.64 no (*1) 14.5 14.71 1.21 -1.29 no (*1) tune-up 2462 1 13.5 16.0 0.00 14.5 14.18 0.68 -1.82 no (*1) 14.5 14.52 1.02 -1.48 no (*1) tune-up 2417 6 17.0 19.5 0.03 17.0 17.77 0.77 -1.73 Yes 17.0 18.08 1.08 -1.42 Yes default 2417 9 17.0 19.5 0.04 17.0 17.70 0.70 -1.80 - 17.0 17.98 0.98 -1.52 - default 2417 12 17.0 19.5 0.06 17.0 17.67 0.67 -1.83 - 17.0 17.94 0.94 -1.56 - default 2417 18 17.0 19.5 0.09 17.0 17.70 0.70 -1.80 - 17.0 17.95 0.95 -1.55 - default 2417 24 17.0 19.5 0.11 17.0 17.69 0.69 -1.81 - 17.0 17.94 0.94 -1.56 - default 2417 36 17.0 19.5 0.16 17.0 17.68 0.68 -1.82 - 17.0 17.94 0.94 -1.56 - default 11g 2417 48 16.0 18.5 0.21 16.0 16.19 0.19 -2.31 - 16.0 17.10 1.10 -1.40 - default 2417 56 15.0 17.5 0.24 15.0 15.00 0.00 -2.50 - 15.0 16.10 1.10 -1.40 - default 2412 6 13.5 16.0 0.03 13.5 14.38 0.88 -1.62 no (*1) 13.5 14.57 1.07 -1.43 no (*1) default 2437 6 16.0 18.5 0.03 16.0 16.25 0.25 -2.25 - 16.0 16.98 0.98 -1.52 no (*1) default 2462 6 15.0 17.5 0.03 15.0 15.22 0.22 -2.28 - 15.0 16.06 1.06 -1.44 no (*1) default 2437 6 15.5 18.0 0.03 16.5 16.63 0.63 -1.87 no (*1) - - - - - tune-up 2462 6 15.0 17.5 0.03 15.5 15.65 0.65 -1.85 no (*1) - - - - - tune-up 2417 MCS0 14.5 17.0 0.03 14.5 15.00 0.50 -2.00 Yes 14.5 15.76 1.26 -1.24 Yes default 2417 MCS1 14.5 17.0 0.06 14.5 14.90 0.40 -2.10 - 14.5 15.62 1.12 -1.38 - default 2417 MCS2 14.5 17.0 0.09 14.5 14.90 0.40 -2.10 - 14.5 15.56 1.06 -1.44 - default 2417 MCS3 14.5 17.0 0.12 14.5 14.88 0.38 -2.12 - 14.5 15.57 1.07 -1.43 - default 11n 2417 MCS4 14.5 17.0 0.17 14.5 14.83 0.33 -2.17 - 14.5 15.57 1.07 -1.43 - default (20HT) 2417 MCS5 14.5 17.0 0.22 14.5 14.42 042 -2.08 - 14.5 14.80 0.80 -1.70 - default (1Tx) 2417 MCS6 14.5 17.0 0.24 14.5 14.08 0.58 -1.92 - 14.5 14.21 0.71 -1.79 - default 2417 MCS7 14.5 17.0 0.27 14.5 13.62 0.62 -1.88 - 14.5 13.83 0.83 -1.67 - default 2412 MCS0 10.5 13.0 0.03 10.5 11.96 1.46 -1.04 no (*1) 10.5 11.76 1.26 -1.24 no (*1) default 2437 MCS0 12.5 15.0 0.03 12.5 13.08 0.58 -1.92 no (*1) 12.5 13.59 1.09 -1.41 no (*1) default 2462 MCS0 10.5 13.0 0.03 10.5 10.66 0.16 -2.34 no (*1) 10.5 11.26 0.76 -1.74 no (*1) default 2427 MCS0 13.5 16.0 0.06 13.5 14.19 0.69 -1.81 Yes 13.5 14.76 1.26 -1.24 Yes default 2427 MCS1 13.5 16.0 0.12 13.5 14.17 0.67 -1.83 - 13.5 14.66 1.16 -1.34 - default 2427 MCS2 13.5 16.0 0.17 13.5 14.13 0.63 -1.87 - 13.5 14.66 1.16 -1.34 - default 2427 MCS3 13.5 16.0 0.22 13.5 13.99 0.49 -2.01 - 13.5 14.57 1.07 -1.43 - default 11n 2427 MCS4 13.5 16.0 0.31 13.5 14.01 0.51 -1.99 - 13.5 14.69 1.19 -1.31 - default (40HT) 2427 MCS5 13.0 15.5 0.39 13.5 13.70 0.70 -1.80 - 13.5 13.89 0.89 -1.61 - default (1Tx) 2427 MCS6 12.5 15.0 0.43 13.5 13.12 0.62 -1.88 - 13.5 13.47 0.97 -1.53 - default 2427 MCS7 12.0 14.5 0.47 13.5 12.93 0.93 -1.57 - 13.5 13.08 1.08 -1.42 - default 2422 MCS0 6.0 8.5 0.06 6.0 6.63 0.63 -1.87 no (*1) 6.0 8.03 2.03 -0.47 no (*1) default 2437 MCS0 10.5 13.0 0.06 10.5 11.73 1.23 -1.27 no (*1) 10.5 12.07 1.57 -0.93 no (*1) default 2452 MCS0 7.0 9.5 0.06 7.0 7.89 0.89 -1.61 no (*1) 7.0 8.40 1.40 -1.10 no (*1) default 2417 MCS8 14.5 17.0 0.06 14.5 15.01 0.51 -1.99 no (*2) 14.5 15.71 1.21 -1.29 no (*2) 17.5 20.0 18.38 0.88 -1.62 default 2417 MCS9 14.5 17.0 0.12 14.5 14.98 0.48 -2.02 - 14.5 15.55 1.05 -1.45 - 17.5 20.0 18.28 0.78 -1.72 default 2417 MCS10 14.5 17.0 0.17 14.5 14.98 0.48 -2.02 - 14.5 15.41 091 -1.59 - 17.5 20.0 18.21 0.71 -1.79 default 2417 MCS11 14.5 17.0 0.22 14.5 14.94 0.44 -2.06 - 14.5 15.39 0.89 -1.61 - 17.5 20.0 18.18 0.68 -1.82 default 11n 2417 MCS12 14.5 17.0 0.31 14.5 14.90 0.40 -2.10 - 14.5 15.57 1.07 -1.43 - 17.5 20.0 18.26 0.76 -1.74 default (20HT) 2417 MCS13 14.0 16.5 0.39 14.0 14.62 0.62 -1.88 - 14.0 15.09 1.09 -1.41 - 17.0 19.5 17.87 0.87 -1.63 default (2Tx) 2417 MCS14 13.5 16.0 0.43 13.5 14.36 0.86 -1.64 - 13.5 14.41 0.91 -1.59 - 16.5 19.0 17.40 0.90 -1.60 default 2417 MCS15 13.0 15.5 0.46 13.0 13.77 0.77 -1.73 - 13.0 14.16 1.16 -1.34 - 16.0 18.5 16.98 0.98 -1.52 default 2412 MCS8 10.5 13.0 0.06 10.5 12.04 1.54 -0.96 no (*2) 10.5 12.10 1.60 -0.90 no (*2) 13.5 16.0 15.08 1.58 -0.92 default 2437 MCS8 12.5 15.0 0.06 12.5 13.40 0.90 -1.60 no (*2) 12.5 13.82 1.32 -1.18 no (*2) 15.0 17.5 16.63 1.13 -1.37 default 2462 MCS8 10.5 13.0 0.06 10.5 11.16 0.66 -1.84 no (*2) 10.5 11.45 0.95 -1.55 no (*2) 13.5 16.0 14.32 0.82 -1.68 default 2427 MCS8 13.5 16.0 0.12 13.5 14.15 0.65 -1.85 no (*2) 13.5 14.96 -1.04 no (*2) 16.5 19.0 17.58 1.08 -1.42 default 2427 MCS9 13.5 16.0 0.22 13.5 14.12 0.62 -1.88 - 13.5 14.93 -1.07 - 16.5 19.0 17.55 1.05 -1.45 default 2427 MCS10 13.5 16.0 0.31 13.5 14.13 0.63 -1.87 - 13.5 14.92 -1.08 - 16.5 19.0 17.55 1.05 -1.45 default 2427 MCS11 13.5 16.0 0.38 13.5 14.03 0.53 -1.97 - 13.5 14.74 -1.26 - 16.5 19.0 17.41 0.91 -1.59 default 11n 2427 MCS12 13.5 16.0 0.52 13.5 14.01 0.51 -1.99 - 13.5 14.98 -1.02 - 16.5 19.0 17.53 1.03 -1.47 default (40HT) 2427 MCS13 13.0 15.5 0.64 13.0 13.78 0.78 -1.72 - 13.0 14.24 -1.26 - 16.0 18.5 17.03 1.03 -1.47 default (2Tx) 2427 MCS14 12.5 15.0 0.67 12.5 13.48 0.98 -1.52 - 12.5 13.68 -1.32 - 15.5 18.0 16.59 1.09 -1.41 default 2427 MCS15 12.0 14.5 0.71 12.0 13.11 1.11 -1.39 - 12.0 13.42 -1.08 - 15.0 17.5 16.28 1.28 -1.22 default 2422 MCS8 6.0 8.5 0.12 6.0 7.08 1.08 -1.42 no (*2) 6.0 7.90 1.90 -0.60 no (*2) 9.0 11.5 10.52 1.52 -0.98 default 2437 MCS8 10.5 13.0 0.12 10.5 11.83 1.33 -1.17 no (*2) 10.5 12.23 1.73 -0.77 no (*2) 12.5 15.0 15.04 1.54 -0.96 default 2452 MCS8 7.0 9.5 0.12 7.0 8.17 1.17 -1.33 no (*2) 7.0 8.40 1.40 -1.10 no (*2) 10.0 12.5 11.30 1.30 -1.20 default *. : SAR test was applied. UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401

Test report No. : 10318894S-C Page : 12 of 88 Issued date : October 9, 2014 FCC ID : W2Z-01000006 (for table of 6.1.1: 2412-2462MHz) *1. (KDB248227) Since the extrapolated maximum peak SAR for the maximum output channel was 1.6W/kg and the 1g averaged SAR was 0.8W/kg, the testing for other channels were omitted. (*. By Clause 4.3.3 of KDB447498 D01, 1g averaged SAR (reported) was 0.8W/kg, when the Tx band is  100MHz.) *2. (KDB447498) Since SPLSR (SAR to peak location separation ratio) was enough smaller than 0.04, SAR test of MIMO mode was reduced. *. Freq.: Frequency, Typ.: Typical, Max.: Maximum, Power spec.: Power specification, Set pwr: Setting power for the measurement, Ave.: Average *. Calculating formula: target.(dB)= (measured power, dBm) - (Typ.target power, dBm); Max.(dB)= (measured power, dBm) - (Max. specification power, dBm) Results (Ave, dBm) = (P/M Reading, dBm)+(Cable loss, dBm)+(Attenuator, dBm)+(duty factor, dBm), where (duty factor, dBm)=10  log (100/(duty cycle, %)) *. Date measured May 7, 8, 9 and 20, 2014 / measured by: T. Arai, H. Shirasawa, S. Takano, H. Naka (2327deg.C./3750%RH, at M/R#1 and Pre-S/R#7) *. Uncertainty of antenna port conducted test; Power measurement uncertainty above 1GHz for this test was: (±) 1.5dB 6.1.2 5180-5240&5260-5320MHz: W52&53 band Power spec. Duty Standalone: Antenna #0 (chain #0) Standalone: Antenna #1 (chain #1) MIMO Ant.#0+Ant.#1 Data Mode Freq. rate Typ. Max. factor Set Ave.   Apply Set Ave.   Apply MIMO MIMO SUM   Meas. pwr. Power target target Max. SAR pwr. target Max. SAR target max. Ave. target Max. Tune-up [MHz] [Mbps] [dBm] [dBm] [dB] [dB] [dBm] [dB] [dB] test? [dBm] [dBm] [dB] [dBm] test? [dBm] [dBm] [dBm] [dB] [dB] 5180 6 12.5 15.0 0.02 12.5 12.82 0.32 -2.18 no (*1) 12.5 12.80 0.30 -2.20 - default 5200 6 12.5 15.0 0.02 12.5 12.65 0.15 -2.35 - 12.5 12.63 0.13 -2.37 - default 5220 6 12.5 15.0 0.02 12.5 12.86 0.36 -2.14 - 12.5 13.16 0.66 -1.84 - default 5240 6 12.5 15.0 0.02 12.5 13.18 0.68 -1.82 no (*1) 12.5 12.73 0.23 -2.27 - default 5260 6 12.5 15.0 0.02 12.5 13.29 0.79 -1.71 Yes 12.5 12.84 0.34 -2.16 - default 5280 6 12.5 15.0 0.02 12.5 13.11 0.61 -1.89 - 12.5 12.95 0.45 -2.05 - default 11a 5300 6 12.5 15.0 0.02 12.5 13.19 0.69 -1.81 - 12.5 13.37 0.87 -1.63 - default 5320 6 12.5 15.0 0.02 12.5 13.09 0.59 -1.91 no (*1) 12.5 13.16 0.66 -1.84 - default 5180 6 12.5 15.0 0.02 - - - - - 13.5 13.33 0.83 -1.67 no (*1) tune-up 5240 6 12.5 15.0 0.02 - - - - - 13.5 13.52 1.02 -1.48 no (*1) tune-up 5260 6 12.5 15.0 0.02 - - - - - 13.5 13.61 1.11 -1.39 no (*1) tune-up 5300 6 12.5 15.0 0.02 - - - - - 13.5 13.94 1.44 -1.06 Yes tune-up 5320 6 12.5 15.0 0.02 - - - - - 13.5 13.73 1.23 -1.27 - tune-up 5180 MCS0 11.0 13.5 0.02 11.0 11.20 0.20 -2.30 no (*2) 11.0 11.68 0.68 -1.82 no (*2) default 5200 MCS0 11.0 13.5 0.02 11.0 11.34 0.34 -2.16 - 11.0 11.60 0.60 -1.90 - default 5220 MCS0 11.0 13.5 0.02 11.0 11.44 0.44 -2.06 - 11.0 11.51 0.51 -1.99 - default 11n 5240 MCS0 11.0 13.5 0.02 11.0 11.86 0.86 -1.64 no (*2) 11.0 11.70 0.70 -1.80 no (*2) default (20HT) (1Tx) 5260 MCS0 11.0 13.5 0.02 11.0 11.73 0.73 -1.77 no (*2) 11.0 11.63 0.63 -1.87 no (*2) default 5280 MCS0 11.0 13.5 0.02 11.0 11.66 0.66 -1.84 - 11.0 11.66 0.66 -1.84 - default 5300 MCS0 11.0 13.5 0.02 11.0 11.71 0.71 -1.79 - 11.0 11.85 0.85 -1.65 - default 5320 MCS0 11.0 13.5 0.02 11.0 11.71 0.71 -1.79 no (*2) 11.0 11.91 0.91 -1.59 no (*2) default 5190 MCS0 10.0 12.5 0.05 10.0 10.30 0.30 -2.20 no (*2) 10.0 10.69 0.69 -1.81 no (*2) default 5230 MCS0 11.0 13.5 0.05 11.0 11.97 0.97 -1.53 Yes 11.0 11.55 0.55 -1.95 - default 11n 5270 MCS0 11.0 13.5 0.05 11.0 11.81 0.81 -1.69 no (*2) 11.0 11.43 0.43 -2.07 - default (40HT) (1Tx) 5310 MCS0 10.0 12.5 0.05 10.0 10.77 0.77 -1.73 no (*2) 10.0 10.67 0.67 -1.83 no (*2) default 5230 MCS0 11.0 13.5 0.05 - - - - - 11.5 11.99 0.99 -1.51 no (*2) tune-up 5270 MCS0 11.0 13.5 0.05 - - - - - 11.5 11.82 0.82 -1.68 no (*2) tune-up 5180 MCS8 11.0 13.5 0.04 11.0 11.07 0.07 -2.43 no (*3) 11.0 11.52 0.52 -1.98 no (*3) 14.0 16.5 14.31 0.31 -2.19 default 5200 MCS8 11.0 13.5 0.04 11.0 11.36 0.36 -2.14 - 11.0 11.53 0.53 -1.97 - 14.0 16.5 14.46 0.46 -2.04 default 5220 MCS8 11.0 13.5 0.04 11.0 11.57 0.57 -1.93 - 11.0 11.54 0.54 -1.96 - 14.0 16.5 14.57 0.57 -1.93 default 11n 5240 MCS8 11.0 13.5 0.04 11.0 12.01 1.01 -1.49 no (*3) 11.0 11.68 0.68 -1.82 no (*3) 14.0 16.5 14.86 0.86 -1.64 default (20HT) (2Tx) 5260 MCS8 11.0 13.5 0.04 11.0 11.97 0.97 -1.53 no (*3) 11.0 11.67 0.67 -1.83 no (*3) 14.0 16.5 14.83 0.83 -1.67 default 5280 MCS8 11.0 13.5 0.04 11.0 11.80 0.80 -1.70 - 11.0 11.69 0.69 -1.81 - 14.0 16.5 14.76 0.76 -1.74 default 5300 MCS8 11.0 13.5 0.04 11.0 11.86 0.86 -1.64 no (*3) 11.0 11.87 0.87 -1.63 no (*3) 14.0 16.5 14.88 0.88 -1.62 default 5320 MCS8 11.0 13.5 0.04 11.0 11.87 0.87 -1.63 - 11.0 11.78 0.78 -1.72 - 14.0 16.5 14.84 0.84 -1.66 default 5190 MCS8 10.0 12.5 0.08 10.0 10.41 0.41 -2.09 no (*3) 10.0 10.68 0.68 -1.82 no (*3) 13.0 15.5 13.56 0.56 -1.94 default 11n 5230 MCS8 11.0 13.5 0.08 11.0 11.95 0.95 -1.55 no (*3) 11.0 11.55 0.55 -1.95 no (*3) 14.0 16.5 14.77 0.77 -1.73 default (40HT) (2Tx) 5270 MCS8 11.0 13.5 0.08 11.0 11.80 0.80 -1.70 no (*3) 11.0 11.58 0.58 -1.92 no (*3) 14.0 16.5 14.70 0.70 -1.80 default 5310 MCS8 10.0 12.5 0.08 10.0 10.90 0.90 -1.60 no (*3) 10.0 10.74 0.74 -1.76 no (*3) 13.0 15.5 13.83 0.83 -1.67 default *. : SAR test was applied. *1. (KDB248227) Since the extrapolated maximum peak SAR for the maximum output channel was 1.6W/kg and the 1g averaged SAR was 0.8W/kg, the testing for other channels were omitted. (*. By Clause 4.3.3 of KDB447498 D01, 1g averaged SAR (reported) was 0.6W/kg, when the Tx band is 100200MHz.) *2. (KDB248227) Since the average power of 11n(20HT)(SISO) and 11n(40HT)(SISO) were more than 1dB lower than the corresponded 11a power and measured SAR(1g) of 11a mode was very small, SAR test was reduced for 11n(20HT)(SISO) mode and SAR test of n(40HT) was only considered for the worst SAR antenna of 11a mode with highest power channel. *3. (KDB447498) Since SPLSR (SAR to peak location separation ratio) was enough smaller than 0.04, SAR test of MIMO mode was reduced. *. Freq.: Frequency, Typ.: Typical, Max.: Maximum, Power spec.: Power specification, Set pwr: Setting power for the measurement, Ave.: Average *. Calculating formula: target.(dB)= (measured power, dBm) - (Typ.target power, dBm); Max.(dB)= (measured power, dBm) - (Max. specification power, dBm) Results (Ave, dBm) = (P/M Reading, dBm)+(Cable loss, dBm)+(Attenuator, dBm)+(duty factor, dBm), where (duty factor, dBm)=10  log (100/(duty cycle, %)) *. Date measured May 7, 8, 9 and 20, 2014 / measured by: T. Arai, H. Shirasawa, S. Takano, H. Naka (2327deg.C./3750%RH, at M/R#1 and Pre-S/R#7) *. Uncertainty of antenna port conducted test; Power measurement uncertainty above 1GHz for this test was: (±) 1.5dB UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401

Test report No. : 10318894S-C Page : 13 of 88 Issued date : October 9, 2014 FCC ID : W2Z-01000006 6.1.3 5500-5700MHz: W56 band Power spec. Duty Standalone: Antenna #0 (chain #0) Standalone: Antenna #1 (chain #1) MIMO Ant.#0+Ant.#1 Data Mode Freq. rate Typ. Max. factor Set Ave.   Apply Set Ave.   Apply MIMO MIMO SUM   Meas. pwr. Power target target Max. SAR pwr. target Max. SAR target max. Ave. target Max. Tune-up [MHz] [Mbps] [dBm] [dBm] [dB] [dB] [dBm] [dB] [dB] test? [dBm] [dBm] [dB] [dBm] test? [dBm] [dBm] [dBm] [dB] [dB] 5500 6 15.0 17.5 0.02 15.0 15.19 0.19 -2.31 - 15.0 15.20 0.20 -2.30 - default 5500 9 15.0 17.5 0.03 15.0 15.09 0.09 -2.41 - 15.0 15.15 0.15 -2.35 - default 5500 12 15.0 17.5 0.04 15.0 15.12 0.12 -2.38 - 15.0 15.08 0.08 -2.42 - default 5500 18 15.0 17.5 0.06 15.0 15.15 0.15 -2.35 - 15.0 15.16 0.16 -2.34 - default 5500 24 15.0 17.5 0.08 15.0 15.13 0.13 -2.37 - 15.0 15.13 0.13 -2.37 - default 5500 36 15.0 17.5 0.11 15.0 15.17 0.17 -2.33 - 15.0 15.05 0.05 -2.45 - default 5500 48 15.0 17.5 0.15 15.0 15.17 0.17 -2.33 - 15.0 15.18 0.18 -2.32 - default 5500 56 14.0 16.5 0.17 14.0 14.30 0.30 -2.20 - 14.0 14.28 0.28 -2.22 - default 5520 6 15.0 17.5 0.02 15.0 15.15 0.15 -2.35 - 15.0 15.01 0.01 -2.49 - default 5540 6 15.0 17.5 0.02 15.0 15.25 0.25 -2.25 - 15.0 15.18 0.18 -2.32 - default 5560 6 15.0 17.5 0.02 15.0 15.33 0.33 -2.17 - 15.0 15.39 0.39 -2.11 - default 11a 5580 6 15.0 17.5 0.02 15.0 15.16 0.16 -2.34 - 15.0 15.52 0.52 -1.98 - default 5600 6 15.0 17.5 0.02 15.0 15.02 0.02 -2.48 - 15.0 15.49 0.49 -2.01 - default 5620 6 15.0 17.5 0.02 15.0 15.20 0.20 -2.30 - 15.0 15.51 0.51 -1.99 - default 5640 6 15.0 17.5 0.02 15.0 15.13 0.13 -2.37 - 15.0 15.49 0.49 -2.01 - default 5660 6 15.0 17.5 0.02 15.0 15.08 0.08 -2.42 - 15.0 15.46 0.46 -2.04 - default 5680 6 15.0 17.5 0.02 15.0 15.35 0.35 -2.15 - 15.0 15.48 0.48 -2.02 - default 5700 6 15.0 17.5 0.02 15.0 15.33 0.33 -2.17 - 15.0 15.29 0.29 -2.21 - default 5520 6 15.0 17.5 0.02 15.5 15.62 0.62 -1.88 no (*1) 16.0 15.76 0.76 -1.74 no (*1) tune-up 5580 6 15.0 17.5 0.02 15.5 15.64 0.64 -1.86 no (*1) 16.0 16.02 1.02 -1.48 no (*1) tune-up 5620 6 15.0 17.5 0.02 15.5 15.67 0.67 -1.83 no (*1) 16.0 16.12 1.12 -1.38 no (*1) tune-up 5680 6 15.0 17.5 0.02 15.5 16.01 1.01 -1.49 Yes 16.0 16.53 1.53 -0.97 Yes tune-up 5500 MCS0 13.5 16.0 0.02 13.5 13.93 0.43 -2.07 - 13.5 13.96 0.46 -2.04 - default 5500 MCS1 13.5 16.0 0.04 13.5 13.87 0.37 -2.13 - 13.5 13.86 0.36 -2.14 - default 5500 MCS2 13.5 16.0 0.06 13.5 13.85 0.35 -2.15 - 13.5 13.89 0.39 -2.11 - default 5500 MCS3 13.5 16.0 0.08 13.5 13.84 0.34 -2.16 - 13.5 13.88 0.38 -2.12 - default 5500 MCS4 13.5 16.0 0.12 13.5 13.85 0.35 -2.15 - 13.5 13.90 0.40 -2.10 - default 5500 MCS5 12.5 15.0 0.16 12.5 13.18 0.68 -1.82 - 12.5 12.70 0.20 -2.30 - default 5500 MCS6 10.5 13.0 0.17 10.5 11.43 0.93 -1.57 - 10.5 10.56 0.06 -2.44 - default 5500 MCS7 8.5 11.0 0.19 8.5 9.43 0.93 -1.57 - 8.5 8.70 0.20 -2.30 - default 11n 5520 MCS0 13.5 16.0 0.02 13.5 13.92 0.42 -2.08 no (*2) 13.5 13.75 0.25 -2.25 no (*2) default (20HT) (1Tx) 5540 MCS0 13.5 16.0 0.02 13.5 13.93 0.43 -2.07 - 13.5 13.91 0.41 -2.09 - default 5560 MCS0 13.5 16.0 0.02 13.5 13.87 0.37 -2.13 - 13.5 14.01 0.51 -1.99 - default 5580 MCS0 13.5 16.0 0.02 13.5 13.96 0.46 -2.04 no (*2) 13.5 14.23 0.73 -1.77 no (*2) default 5600 MCS0 13.5 16.0 0.02 13.5 13.88 0.38 -2.12 - 13.5 14.11 0.61 -1.89 - default 5620 MCS0 13.5 16.0 0.02 13.5 13.96 0.46 -2.04 no (*2) 13.5 14.09 0.59 -1.91 no (*2) default 5640 MCS0 13.5 16.0 0.02 13.5 13.89 0.39 -2.11 - 13.5 14.14 0.64 -1.86 - default 5660 MCS0 13.5 16.0 0.02 13.5 13.96 0.46 -2.04 - 13.5 14.05 0.55 -1.95 - default 5680 MCS0 13.5 16.0 0.02 13.5 14.00 0.50 -2.00 no (*2) 13.5 14.16 0.66 -1.84 - default 5700 MCS0 13.5 16.0 0.02 13.5 13.97 0.47 -2.03 - 13.5 14.21 0.71 -1.79 no (*2) default 5510 MCS0 11.0 13.5 0.05 11.0 11.76 0.76 -1.74 no (*2) 11.0 11.29 0.29 -2.21 no (*2) default 5510 MCS1 11.0 13.5 0.08 11.0 11.66 0.66 -1.84 - 11.0 11.23 0.23 -2.27 - default 5510 MCS2 11.0 13.5 0.12 11.0 11.64 0.64 -1.86 - 11.0 11.25 0.25 -2.25 - default 5510 MCS3 11.0 13.5 0.16 11.0 11.66 0.66 -1.84 - 11.0 11.22 0.22 -2.28 - default 5510 MCS4 11.0 13.5 0.22 11.0 11.70 0.70 -1.80 - 11.0 11.27 0.27 -2.23 - default 11n 5510 MCS5 11.0 13.5 0.28 11.0 11.72 0.72 -1.78 - 11.0 11.20 0.20 -2.30 - default (40HT) (1Tx) 5510 MCS6 10.0 12.5 0.31 10.0 10.84 0.84 -1.66 - 10.0 10.03 0.03 -2.47 - default 5510 MCS7 8.0 10.5 0.34 8.0 8.85 0.85 - (*1) - 8.0 8.48 0.48 -2.02 - default 5550 MCS0 11.0 13.5 0.05 11.0 11.83 0.83 -1.67 Yes 11.0 11.46 0.46 -2.04 no (*2) default 5590 MCS0 11.0 13.5 0.05 11.0 11.64 0.64 -1.86 - 11.0 11.42 0.42 -2.08 - default 5630 MCS0 11.0 13.5 0.05 11.0 11.58 0.58 -1.92 - 11.0 11.50 0.50 -2.00 - default 5670 MCS0 11.0 13.5 0.05 11.0 11.56 0.56 -1.94 no (*2) 11.0 11.66 0.66 -1.84 no (*2) default *. : SAR test was applied. UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401

Test report No. : 10318894S-C Page : 14 of 88 Issued date : October 9, 2014 FCC ID : W2Z-01000006 6.1.3 5500-5700MHz: W56 band (cont'd) Power spec. Duty Standalone: Antenna #0 (chain #0) Standalone: Antenna #1 (chain #1) MIMO Ant.#0+Ant.#1 Data Mode Freq. rate Typ. Max. factor Set Ave.   Apply Set Ave.   Apply MIMO MIMO SUM   Meas. pwr. Power target target Max. SAR pwr. target Max. SAR target max. Ave. target Max. Tune-up [MHz] [Mbps] [dBm] [dBm] [dB] [dB] [dBm] [dB] [dB] test? [dBm] [dBm] [dB] [dBm] test? [dBm] [dBm] [dBm] [dB] [dB] 5500 MCS8 13.5 16.0 0.04 13.5 14.05 0.55 -1.95 - 13.5 13.87 0.37 -2.13 - 16.5 19.0 16.97 0.47 -2.03 default 5500 MCS9 13.5 16.0 0.08 13.5 13.98 0.48 -2.02 - 13.5 13.74 0.24 -2.26 - 16.5 19.0 16.87 0.37 -2.13 default 5500 MCS10 13.5 16.0 0.12 13.5 13.95 0.45 -2.05 - 13.5 13.75 0.25 -2.25 - 16.5 19.0 16.86 0.36 -2.14 default 5500 MCS11 13.5 16.0 0.15 13.5 13.98 0.48 -2.02 - 13.5 13.83 0.33 -2.17 - 16.5 19.0 16.92 0.42 -2.08 default 5500 MCS12 13.5 16.0 0.22 13.5 14.03 0.53 -1.97 - 13.5 13.79 0.29 -2.21 - 16.5 19.0 16.92 0.42 -2.08 default 5500 MCS13 12.5 15.0 0.28 12.5 13.19 0.69 -1.81 - 12.5 12.45 -0.05 -2.55 - 15.5 18.0 15.85 0.35 -2.15 default 5500 MCS14 10.5 13.0 0.31 10.5 11.42 0.92 -1.58 - 10.5 10.50 0.00 -2.50 - 13.5 16.0 14.00 0.50 -2.00 default 5500 MCS15 8.5 11.0 0.33 8.5 9.44 0.94 -1.56 - 8.5 8.78 0.28 -2.22 - 11.5 14.0 12.13 0.63 -1.87 default 5520 MCS8 13.5 16.0 0.04 13.5 13.99 0.49 -2.01 - 13.5 13.80 0.30 -2.20 - 16.5 19.0 16.91 0.41 -2.09 default 5540 MCS8 13.5 16.0 0.04 13.5 14.04 0.54 -1.96 - 13.5 13.93 0.43 -2.07 - 16.5 19.0 17.00 0.50 -2.00 default 11n 5560 MCS8 13.5 16.0 0.04 13.5 14.01 0.51 -1.99 - 13.5 14.00 0.50 -2.00 - 16.5 19.0 17.02 0.52 -1.98 default (20HT) (2Tx) 5580 MCS8 13.5 16.0 0.04 13.5 14.01 0.51 -1.99 - 13.5 14.17 0.67 -1.83 - 16.5 19.0 17.10 0.60 -1.90 default 5600 MCS8 13.5 16.0 0.04 13.5 13.98 0.48 -2.02 - 13.5 14.07 0.57 -1.93 - 16.5 19.0 17.04 0.54 -1.96 default 5620 MCS8 13.5 16.0 0.04 13.5 13.96 0.46 -2.04 - 13.5 14.13 0.63 -1.87 - 16.5 19.0 17.06 0.56 -1.94 default 5640 MCS8 13.5 16.0 0.04 13.5 13.98 0.48 -2.02 - 13.5 14.02 0.52 -1.98 - 16.5 19.0 17.01 0.51 -1.99 default 5660 MCS8 13.5 16.0 0.04 13.5 14.00 0.50 -2.00 - 13.5 14.02 0.52 -1.98 - 16.5 19.0 17.02 0.52 -1.98 default 5680 MCS8 13.5 16.0 0.04 13.5 14.20 0.70 -1.80 - 13.5 14.20 0.70 -1.80 - 16.5 19.0 17.21 0.71 -1.79 default 5700 MCS8 13.5 16.0 0.04 13.5 13.97 0.47 -2.03 - 13.5 13.89 0.39 -2.11 - 16.5 19.0 16.94 0.44 -2.06 default 5520 MCS8 13.5 16.0 0.04 14.0 14.44 0.94 -1.56 no (*3) 14.0 14.31 0.81 -1.69 no (*3) 16.5 19.0 17.39 0.89 -1.61 tune-up 5580 MCS8 13.5 16.0 0.04 14.0 14.45 0.95 -1.55 no (*3) 14.0 14.71 1.21 -1.29 no (*3) 16.5 19.0 17.59 1.09 -1.41 tune-up 5620 MCS8 13.5 16.0 0.04 14.0 14.52 1.02 -1.48 no (*3) 14.0 14.65 1.15 -1.35 no (*3) 16.5 19.0 17.60 1.10 -1.40 tune-up 5680 MCS8 13.5 16.0 0.04 14.0 14.72 1.22 -1.28 no (*3) 14.0 14.76 1.26 -1.24 no (*3) 16.5 19.0 17.75 1.25 -1.25 tune-up 5510 MCS8 11.0 13.5 0.08 11.0 11.80 0.80 -1.70 - 11.0 11.23 0.23 -2.27 - 14.0 16.5 14.53 0.53 -1.97 default 5510 MCS9 11.0 13.5 0.15 11.0 11.70 0.70 -1.80 - 11.0 11.17 0.17 -2.33 - 14.0 16.5 14.45 0.45 -2.05 default 5510 MCS10 11.0 13.5 0.22 11.0 11.75 0.75 -1.75 - 11.0 11.21 0.21 -2.29 - 14.0 16.5 14.50 0.50 -2.00 default 5510 MCS11 11.0 13.5 0.27 11.0 11.78 0.78 -1.72 - 11.0 11.20 0.20 -2.30 - 14.0 16.5 14.51 0.51 -1.99 default 5510 MCS12 11.0 13.5 0.38 11.0 11.75 0.75 -1.75 - 11.0 11.15 0.15 -2.35 - 14.0 16.5 14.47 0.47 -2.03 default 5510 MCS13 11.0 13.5 0.45 11.0 11.75 0.75 -1.75 - 11.0 11.17 0.17 -2.33 - 14.0 16.5 14.48 0.48 -2.02 default 11n 5510 MCS14 10.0 12.5 0.48 11.0 10.82 0.82 -1.68 - 11.0 10.00 0.00 -2.50 - 14.0 16.5 13.44 0.44 -2.06 default (40HT) 5510 MCS15 8.0 10.5 0.51 11.0 9.02 1.02 -1.48 - 11.0 8.37 0.37 -2.13 - 14.0 16.5 11.72 0.72 -1.78 default (2Tx) 5550 MCS8 11.0 13.5 0.08 11.0 11.84 0.84 -1.66 - 11.0 11.45 0.45 -2.05 - 14.0 16.5 14.66 0.66 -1.84 default 5590 MCS8 11.0 13.5 0.08 11.0 11.75 0.75 -1.75 - 11.0 11.50 0.50 -2.00 - 14.0 16.5 14.64 0.64 -1.86 default 5630 MCS8 11.0 13.5 0.08 11.0 11.73 0.73 -1.77 - 11.0 11.55 0.55 -1.95 - 14.0 16.5 14.65 0.65 -1.85 default 5670 MCS8 11.0 13.5 0.08 11.0 11.66 0.66 -1.84 - 11.0 11.61 0.61 -1.89 - 14.0 16.5 14.65 0.65 -1.85 default 5510 MCS8 11.0 13.5 0.08 12.0 12.83 1.83 -0.67 no (*3) 12.0 12.28 1.28 -1.22 no (*3) 14.0 16.5 15.57 1.57 -0.93 tune-up 5550 MCS8 11.0 13.5 0.08 12.0 12.78 1.78 -0.72 no (*3) 12.0 12.43 1.43 -1.07 no (*3) 14.0 16.5 15.62 1.62 -0.88 tune-up 5670 MCS8 11.0 13.5 0.08 12.0 12.69 1.69 -0.81 no (*3) 12.0 12.70 1.70 -0.80 no (*3) 14.0 16.5 15.71 1.71 -0.79 tune-up *. : SAR test was applied. (for table of 6.1.3: 5500-5700MHz) *1. (KDB248227) Since the extrapolated maximum peak SAR for the maximum output channel was 1.6W/kg and the 1g averaged SAR was 0.8W/kg, the testing for other channels were omitted. (By Clause 4.3.3 of KDB447498 D01, 1g averaged SAR (reported) was 0.4W/kg, when the Tx band is  200MHz.) *2. (KDB248227) Since the average power of 11n(20HT)(SISO)(typical=13.5dBm) and 11n(40HT)(SISO) (typical=11.0dBm) were enough lower than the corresponded 11a power(typical=15.0dBm) and measured SAR(1g) of 11a mode was very small, SAR test was reduced for 11n(20HT)(SISO) mode and SAR test of n(40HT) was only considered for the worst SAR antenna of 11a mode with highest power channel. *3. (KDB447498) Since SPLSR (SAR to peak location separation ratio) was enough smaller than 0.04, SAR test of MIMO mode was reduced. *. Freq.: Frequency, Typ.: Typical, Max.: Maximum, Power spec.: Power specification, Set pwr: Setting power for the measurement, Ave.: Average *. Calculating formula: target.(dB)= (measured power, dBm) - (Typ.target power, dBm); Max.(dB)= (measured power, dBm) - (Max. specification power, dBm) Results (Ave, dBm) = (P/M Reading, dBm)+(Cable loss, dBm)+(Attenuator, dBm)+(duty factor, dBm), where (duty factor, dBm)=10  log (100/(duty cycle, %)) *. Date measured May 7, 8, 9 and 20, 2014 / measured by: T. Arai, H. Shirasawa, S. Takano, H. Naka (2327deg.C./3750%RH, at M/R#1 and Pre-S/R#7) *. Uncertainty of antenna port conducted test; Power measurement uncertainty above 1GHz for this test was: (±) 1.5dB UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401

Test report No. : 10318894S-C Page : 15 of 88 Issued date : October 9, 2014 FCC ID : W2Z-01000006 6.1.4 5745-5825MHz: W58 band Power spec. Duty Standalone: Antenna #0 (chain #0) Standalone: Antenna #1 (chain #1) MIMO Ant.#0+Ant.#1 Data Mode Freq. rate Typ. Max. factor Set Ave.   Apply Set Ave.   Apply MIMO MIMO SUM   Meas. pwr. Power target target Max. SAR pwr. target Max. SAR target max. Ave. target Max. Tune-up [MHz] [Mbps] [dBm] [dBm] [dB] [dB] [dBm] [dB] [dB] test? [dBm] [dBm] [dB] [dBm] test? [dBm] [dBm] [dBm] [dB] [dB] 5745 6 15.0 17.5 0.02 15.0 15.56 0.56 -1.94 no (*1) 15.0 15.17 0.17 -2.33 - default 5765 6 15.0 17.5 0.02 15.0 15.62 0.62 -1.88 - 15.0 15.08 0.08 -2.42 - default 5785 6 15.0 17.5 0.02 15.0 15.70 0.70 -1.80 no (*1) 15.0 14.90 -0.10 -2.60 - default 5805 6 15.0 17.5 0.02 15.0 15.73 0.73 -1.77 Yes 15.0 15.09 0.09 -2.41 - default 5825 6 15.0 17.5 0.02 15.0 15.66 0.66 -1.84 - 15.0 15.16 0.16 -2.34 - default 11a 5745 6 15.0 17.5 0.02 - - - - - 16.0 16.19 1.19 -1.31 Yes tune-up 5765 6 15.0 17.5 0.02 - - - - - 16.0 15.90 0.90 -1.60 - tune-up 5785 6 15.0 17.5 0.02 - - - - - 16.0 15.91 0.91 -1.59 no (*1) tune-up 5805 6 15.0 17.5 0.02 - - - - - 16.0 15.83 0.83 -1.67 - tune-up 5825 6 15.0 17.5 0.02 - - - - - 16.0 15.97 0.97 -1.53 no (*1) tune-up 5745 MCS0 13.5 16.0 0.02 13.5 14.07 0.57 -1.93 no (*2) 13.5 13.64 0.14 -2.36 no (*2) default 11n 5765 MCS0 13.5 16.0 0.02 13.5 14.28 0.78 -1.72 no (*2) 13.5 13.49 -0.01 -2.51 - default (20HT) 5785 MCS0 13.5 16.0 0.02 13.5 14.00 0.50 -2.00 - 13.5 13.20 -0.30 -2.80 no (*2) default (1Tx) 5805 MCS0 13.5 16.0 0.02 13.5 14.13 0.63 -1.87 - 13.5 13.24 -0.26 -2.76 - default 5825 MCS0 13.5 16.0 0.02 13.5 14.12 0.62 -1.88 no (*2) 13.5 13.34 -0.16 -2.66 no (*2) default 5755 MCS0 11.0 13.5 0.05 11.0 11.61 0.61 -1.89 - 11.0 10.93 -0.07 -2.57 - default 11n 5795 MCS0 11.0 13.5 0.05 11.0 11.35 0.35 -2.15 - 11.0 10.40 -0.60 -3.10 - default (40HT) (1Tx) 5755 MCS0 11.0 13.5 0.05 11.5 12.15 1.15 -1.35 Yes 12.5 12.43 1.43 -1.07 no (*2) tune-up 5795 MCS0 11.0 13.5 0.05 11.5 11.80 0.80 -1.70 no (*2) 12.5 12.04 1.04 -1.46 no (*2) tune-up 5745 MCS8 13.5 16.0 0.04 13.5 14.02 0.52 -1.98 - 13.5 13.56 0.06 -2.44 - 16.5 19.0 16.81 0.31 -2.19 default 5765 MCS8 13.5 16.0 0.04 13.5 14.08 0.58 -1.92 - 13.5 13.43 -0.07 -2.57 - 16.5 19.0 16.78 0.28 -2.22 default 5785 MCS8 13.5 16.0 0.04 13.5 14.04 0.54 -1.96 - 13.5 13.26 -0.24 -2.74 - 16.5 19.0 16.68 0.18 -2.32 default 11n 5805 MCS8 13.5 16.0 0.04 13.5 14.14 0.64 -1.86 - 13.5 13.26 -0.24 -2.74 - 16.5 19.0 16.73 0.23 -2.27 default (20HT) (2Tx) 5825 MCS8 13.5 16.0 0.04 13.5 14.16 0.66 -1.84 - 13.5 13.34 -0.16 -2.66 - 16.5 19.0 16.78 0.28 -2.22 default 5745 MCS8 13.5 16.0 0.04 14.5 14.86 1.36 -1.14 no (*3) 14.5 14.43 0.93 -1.57 no (*3) 16.5 19.0 17.66 1.16 -1.34 tune-up 5785 MCS8 13.5 16.0 0.04 14.5 15.06 1.56 -0.94 no (*3) 14.5 14.31 0.81 -1.69 no (*3) 16.5 19.0 17.71 1.21 -1.29 tune-up 5825 MCS8 13.5 16.0 0.04 14.5 15.22 1.72 -0.78 no (*3) 14.5 14.49 0.99 -1.51 no (*3) 16.5 19.0 17.88 1.38 -1.12 tune-up 5755 MCS8 11.0 13.5 0.08 11.0 11.64 0.64 -1.86 - 11.0 10.98 -0.02 -2.52 - 14.0 16.5 14.33 0.33 -2.17 default 11n 5795 MCS8 11.0 13.5 0.08 11.0 11.35 0.35 -2.15 - 11.0 10.38 -0.62 -3.12 - 14.0 16.5 13.90 -0.10 -2.60 default (40HT) (2Tx) 5755 MCS8 11.0 13.5 0.08 12.5 13.15 2.15 -0.35 no (*3) 12.5 12.74 1.74 -0.76 no (*3) 14.0 16.5 15.96 1.96 -0.54 tune-up 5795 MCS8 11.0 13.5 0.08 12.5 12.94 1.94 -0.56 no (*3) 12.5 12.00 1.00 -1.50 no (*3) 14.0 16.5 15.51 1.51 -0.99 tune-up *. : SAR test was applied. *1. (KDB248227) Since the extrapolated maximum peak SAR for the maximum output channel was 1.6W/kg and the 1g averaged SAR was 0.8W/kg, the testing for other channels were omitted. (*. By Clause 4.3.3 of KDB447498 D01, 1g averaged SAR (reported) was 0.8W/kg, when the Tx band is  100MHz.) *2. (KDB248227) Since the average power of 11n(20HT)(SISO)(typical=13.5dBm) and 11n(40HT)(SISO) (typical=11.0dBm) were enough lower than the corresponded 11a power(typical=15.0dBm) and measured SAR(1g) of 11a mode was very small, SAR test was reduced for 11n(20HT)(SISO) mode and SAR test of n(40HT) was only considered for the worst SAR antenna of 11a mode with highest power channel. *3. (KDB447498) Since SPLSR (SAR to peak location separation ratio) was enough smaller than 0.04, SAR test of MIMO mode was reduced. *. Freq.: Frequency, Typ.: Typical, Max.: Maximum, Power spec.: Power specification, Set pwr: Setting power for the measurement, Ave.: Average *. Calculating formula: target.(dB)= (measured power, dBm) - (Typ.target power, dBm); Max.(dB)= (measured power, dBm) - (Max. specification power, dBm) Results (Ave, dBm) = (P/M Reading, dBm)+(Cable loss, dBm)+(Attenuator, dBm)+(duty factor, dBm), where (duty factor, dBm)=10  log (100/(duty cycle, %)) *. Date measured May 7, 8, 9 and 20, 2014 / measured by: T. Arai, H. Shirasawa, S. Takano, H. Naka (2327deg.C./3750%RH, at M/R#1 and Pre-S/R#7) *. Uncertainty of antenna port conducted test; Power measurement uncertainty above 1GHz for this test was: (±) 1.5dB UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401

Test report No. : 10318894S-C Page : 16 of 88 Issued date : October 9, 2014 Revised date : December 12, 2014 (-r03) FCC ID : W2Z-01000006 SECTION 7: Measurement results 7.1 SAR test results (Body) Liquid parameters (Body liquid) (*a) ΔSAR Coefficients (*c) Target Liquid Permittivity (r) [-] Conductivity [S/m] Frequency Temp. Depth ΔSAR Correction Date measured type Measured Limit Measured Limit [deg.C.] [mm] (1g) [%] required? [MHz] Target Target Meas. Δr [%] (*b) Meas. Δ [%] (*b) 2412 52.75 50.74 -3.8 1.914 1.917 +0.9 +0.94 not required. September 12, 2014 2417 52.74 50.70 -3.9 1.918 1.925 +1.0 22.2 155 +1.04 not required. before SAR test 2427 52.73 50.70 -3.9 1.928 1.949 +1.1 +1.41 not required. 5230 48.97 47.69 -2.6 5.334 5.471 +2.6 +0.45 not required. September 9, 2014 5260 48.93 47.59 -2.7 -5%  5.369 5.527 +2.9 0%  22.8 135 +0.46 not required. before SAR test 5300 Body 48.88 47.62 -2.6 r-meas. 5.416 5.543 +2.3 -meas. +0.44 not required. 5550 48.54 47.07 -3.0  0% 5.708 5.898 +3.3  +5% +0.46 not required. 5680 48.36 47.00 -2.8 5.860 6.073 +3.6 +0.39 not required. 5745 48.27 46.78 -3.1 5.936 6.148 +3.6 22.8 136 +0.45 not required. September 8, 2014 before SAR test 5755 48.26 46.96 -2.7 5.947 6.182 +3.9 +0.36 not required. 5805 48.19 46.76 -3.0 6.006 6.264 +4.3 +0.40 not required. SAR measurement results (Body simulated tissue) Reported SAR [MHz] EUT setup conditions Liquid temp. Power SAR (1g) [W/kg] SAR (1g) [W/kg] Data Antenna [deg.C.] maximum value of multi-peak plot # in Average Max. Mode (CH) rate Gap Battery drift Scaled Tuned-up *.SAR Setup [mm] ΔSAR ΔSAR Appendix power power factor SAR (*d) (*1) measured. ID Before/After [dB] Measured [%] corrected 2-2 [dBm] [dBm] 11b 2412(1) 1Mbps 0 #3 22.3/22.4 -0.10 0.023 +0.94 n/a (*c) Plot 1-1 14.47 16.0 1.42 0.033 11g 2417(2) 6Mbps 0 #3 22.4/22.5 0.04 0.023 +1.04 n/a (*c) Plot 1-2 17.77 19.5 1.49 0.034 ant.#0 n(20)(1Tx) 2417(2) MCS0 0 #2 22.5/22.6 0.18 0.022 +1.04 n/a (*c) Plot 1-3 15.00 17.0 1.58 0.035 n(40)(1Tx) 2427(4) MCS0 Front 0 #3 22.6/22.6 -0.04 0.0097 +1.41 n/a (*c) Plot 1-4 14.19 16.0 1.52 0.015 11b 2412(1) 1Mbps (Patient side) 0 #2 22.6/22.7 0.03 0.021 +0.94 n/a (*c) Plot 1-5 15.17 16.0 1.21 0.025 11g 2417(2) 6Mbps 0 #3 22.7/22.7 0.20 0.021 +1.04 n/a (*c) Plot 1-6 18.08 19.5 1.39 0.029 ant.#1 n(20)(1Tx) 2417(2) MCS0 0 #3 22.7/22.7 0.01 0.021 +1.04 n/a (*c) Plot 1-7 15.76 17.0 1.33 0.028 n(40)(1Tx) 2427(4) MCS0 0 #2 22.7/22.7 0.20 0.0061 +1.41 n/a (*c) Plot 1-8 14.76 16.0 1.33 0.008 11a 5260(52) 6Mbps 0 #2 23.0/23.1 0.05 0.113 +0.46 n/a (*c) Plot 2-1 13.29 15.0 1.48 0.17 ant.#0 Front n(40)(1Tx) 5230(46) MCS0 (Patient side) 0 #3 23.1/23.1 0.12 0.083 +0.45 n/a (*c) Plot 2-2 11.97 13.5 1.42 0.12 11a 5300(60) 6Mbps ant.#1 0 #2 22.9/23.1 0.01 0.098 +0.44 n/a (*c) Plot 2-3 13.94 15.0 1.28 0.13 11a 5680(136) 6Mbps 0 #2 22.9/23.0 -0.15 0.140 +0.39 n/a (*c) Plot 2-4 16.01 17.5 1.41 0.20 ant.#0 Front n(40)(1Tx) 5550(110) MCS0 (Patient side) 0 #3 23.0/23.0 0.03 0.095 +0.46 n/a (*c) Plot 2-5 11.83 13.5 1.47 0.14 11a 5680(136) 6Mbps ant.#1 0 #2 22.9/22.9 -0.10 0.124 +0.39 n/a (*c) Plot 2-6 16.53 17.5 1.25 0.16 11a 5805(161) 6Mbps 0 #3 22.8/22.9 -0.20 0.134 +0.40 n/a (*c) Plot 2-7 15.73 17.5 1.50 0.20 ant.#0 Front n(40)(1Tx) 5755(151) MCS0 (Patient side) 0 #2 23.0/23.0 0.10 0.095 +0.36 n/a (*c) Plot 2-8 12.15 13.5 1.36 0.13 11a 5745(149) 6Mbps ant.#1 0 #3 23.0/23.1 0.05 0.100 +0.45 n/a (*c) Plot 2-9 16.19 17.5 1.35 0.14 *. Since this EUT is the medical device, the EUT is only used under the guidance of a doctor or a qualified person. The possibility of the maximum RF human exposure is only a body/head of the patient who comes in contact directly on the front surface side (patient side) of the EUT. Therefore, the SAR test was only applied to the front surface side (patient side) of the EUT. Notes: *1. At the highest output power channel, since the extrapolated maximum peak SAR for the maximum output channel was 1.6W/kg and the 1g averaged SAR was 0.8W/kg, the testing for other channels were omitted. (KDB248227) *. Gap: It is the separation distance between the nearest position of platform outer surface and the bottom outer surface of phantom; n/a: not applied. *. Battery No. #2 and #3were same model. Refer to Appendix 1 for more details. *. During test, the EUT was operated without all signal interface cables (except LAN cable for the Tx control) and with a full-charged battery. *. Calibration frequency of the SAR measurement probe (and used conversion factors) SAR test frequency Probe calibration frequency Validity Conversion factor Uncertainty 2412, 2417, 2427MHz 2450MHz within 50MHz of calibration frequency 6.88 12.0% 5230MHz 5200MHz within 50MHz of calibration frequency 4.35 13.1% 5260, 5300MHz 5300MHz within 50MHz of calibration frequency 4.18 13.1% 5550, 5680MHz 5600MHz within 110MHz of calibration frequency 3.81 13.1% 5745, 5805MHz 5800MHz within 110MHz of calibration frequency 4.05 13.1% *. The uncertainty is the RSS of the ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band. *a. The target value is a parameter defined in Appendix A of KDB865664 D01, the dielectric parameters suggested for head and body tissue simulating liquid are given at 2000, 2450, 3000 and 5800MHz. Parameters for the frequencies 2000-3000, 3000-5800MHz were obtained using linear interpolation, for above 5800MHz were obtained using linear extrapolation (Refer to appendix 3-4.) *b. Refer to KDB865664 D01, item 2), Clause 2.6; "When nominal tissue dielectric parameters are recorded in the probe calibration data; for example, only target values and tolerance are reported, the measured εr and σ of the liquid used in routine measurements must be: ≤ the target εr and ≥ the target σ values and also within 5% of the required target dielectric parameters." *c. The coefficients are parameters defined in clause E.3.3.2, IEEE Std 1528(2013). Since the measured liquid parameters were  the target εr and  the target  values and also within 5% of the required target dielectric parameters, the measured SAR was not compensated by ΔSAR coefficients (*. Clause 2) of 2.6, KDB865664 D01). ΔSAR(1g)= Cεr Δεr + C Δ, Cεr=-7.854E-4f3+9.402E-3f2-2.742E-2f-0.2026 / C =9.804E-3f3-8.661E-2f2+2.981E-2f+0.7829 *d. Tuned-up SAR by scaled factor: Accordance with KDB 447498 D01; "When SAR is not measured at the maximum power level allowed for production units, the results must be scaled to the maximum tune-up tolerance limit according to the power applied to the individual channels tested to determine compliance (clause 4, 4.1, 4)". *. Calculating formula: SAR corrected SAR (1g) (W/kg) = (Observed SAR(1g) (W/kg))  (100 - (SAR(%)) / 100 Reported SAR(1g) (=Tuned-up SAR) (W/kg) = (Observed SAR(1g) (W/kg))  (Scaled factor) UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401

Test report No. : 10318894S-C Page : 17 of 88 Issued date : October 9, 2014 Revised date : December 10, 2014 (-r04) FCC ID : W2Z-01000006 7.2 SAR test results (Head) Liquid parameters (Head liquid) (*a) ΔSAR Coefficients (*c) Target Liquid Permittivity (r) [-] Conductivity [S/m] Frequency Temp. Depth ΔSAR Correction Date measured type Measured Limit Measured Limit [deg.C.] [mm] (1g) [%] required? [MHz] Target Target Meas. Δr (*b) Meas. Δ (*b) 2412 39.27 38.42 -2.2 -5%  1.766 1.803 +2.1 0%  +1.52 not required. September 16, 2014 2417 39.26 38.40 -2.2 r-meas. 1.771 1.815 +2.5 -meas. 23.8 155 +1.71 not required. before SAR test 2427 39.24 38.35 -2.3  0% 1.780 1.821 +2.4  +5% +1.65 not required. 5260 Head 35.92 35.71 -0.6% 4.717 4.525 -4.1% +0.24 not required(*b). September 11, 2014 21.9 154 before SAR test 5300 35.87 35.58 -0.8% -5%  4.758 4.534 -4.7% -5%  +0.31 not required(*b). 5680 35.44 34.96 -1.3% r-meas. 5.147 4.961 -3.6% -meas. +0.43 not required(*b). September 10, 2014 5745 35.36 34.99 -1.1%  +5% 5.214 5.011 -3.9%  +5% 21.9 154 +0.39 not required(*b). before SAR test 5805 35.29 34.77 -1.5% 5.275 5.038 -4.5% +0.49 not required(*b). SAR measurement results (Head simulated tissue) Reported SAR [MHz] EUT setup conditions Liquid temp. Power SAR (1g) [W/kg] SAR (1g) [W/kg] Data Antenna [deg.C.] plot # in Mode (CH) rate Gap Battery drift maximum value of multi-peak Appendix Average Max. Scaled Tuned-up *.SAR Setup [mm] ΔSAR ΔSAR power power factor SAR (*d) (*1) measured. ID Before/After [dB] Measured [%] corrected 2-2 [dBm] [dBm] 11b 2412(1) 1Mbps 0 #2 23.8/23.8 -0.20 0.019 +1.52 n/a (*c) Plot 3-1 14.47 16.0 1.42 0.027 11g 2417(2) 6Mbps 0 #2 23.8/23.8 -0.08 0.017 +1.71 n/a (*c) Plot 3-2 17.77 19.5 1.49 0.025 ant.#0 n(20)(1Tx) 2417(2) MCS0 0 #3 23.8/23.8 0.03 0.018 +1.71 n/a (*c) Plot 3-3 15.00 17.0 1.58 0.028 n(40)(1Tx) 2427(4) MCS0 Front 0 #3 23.9/23.9 -0.16 0.017 +1.65 n/a (*c) Plot 3-4 14.19 16.0 1.52 0.026 11b 2412(1) 1Mbps (Patient side) 0 #3 23.8/23.8 -0.04 0.018 +1.52 n/a (*c) Plot 3-5 15.17 16.0 1.21 0.022 11g 2417(2) 6Mbps 0 #2 23.8/23.9 -0.11 0.018 +1.71 n/a (*c) Plot 3-6 18.08 19.5 1.39 0.025 ant.#1 n(20)(1Tx) 2417(2) MCS0 0 #2 23.9/24.0 0.17 0.018 +1.71 n/a (*c) Plot 3-7 15.76 17.0 1.33 0.024 n(40)(1Tx) 2427(4) MCS0 0 #3 23.9/23.9 0.01 0.017 +1.65 n/a (*c) Plot 3-8 14.76 16.0 1.33 0.023 11a 5260(52) 6Mbps ant.#0 Front 0 #3 22.4/22.5 -0.09 0.057 +0.24 n/a (*c) Plot 4-1 13.29 15.0 1.48 0.08 11a 5300(60) 6Mbps ant.#1 (Patient side) 0 #3 22.1/22.3 -0.18 0.058 +0.31 n/a (*c) Plot 4-2 13.94 15.0 1.28 0.07 11a 5680(136) 6Mbps ant.#0 Front 0 #2 22.3/22.4 0.01 0.071 +0.43 n/a (*c) Plot 4-3 16.01 17.5 1.41 0.10 11a 5680(136) 6Mbps ant.#1 (Patient side) 0 #3 22.0/22.1 -0.01 0.075 +0.43 n/a (*c) Plot 4-4 16.53 17.5 1.25 0.09 11a 5805(161) 6Mbps ant.#0 Front 0 #2 22.0/22.3 0.20 0.071 +0.49 n/a (*c) Plot 4-5 15.73 17.5 1.50 0.11 11a 5745(149) 6Mbps ant.#1 (Patient side) 0 #2 22.5/22.6 0.18 0.063 +0.39 n/a (*c) Plot 4-6 16.19 17.5 1.35 0.09 *. Since this EUT is the medical device, the EUT is only used under the guidance of a doctor or a qualified person. The possibility of the maximum RF human exposure is only a body/head of the patient who comes in contact directly on the front surface side (patient side) of the EUT. Therefore, the SAR test was only applied to the front surface side (patient side) of the EUT. Notes: *1. At the highest output power channel, since the extrapolated maximum peak SAR for the maximum output channel was 1.6W/kg and the 1g averaged SAR was 0.8W/kg, the testing for other channels were omitted. (KDB248227) *. Gap: It is the separation distance between the nearest position of platform outer surface and the bottom outer surface of phantom; n/a: not applied. *. Battery No. #2 and #3were same model. Refer to Appendix 1 for more details. *. During test, the EUT was operated without all signal interface cables (except LAN cable for the Tx control) and with a full-charged battery. *. Calibration frequency of the SAR measurement probe (and used conversion factors) SAR test frequency Probe calibration frequency Validity Conversion factor Uncertainty 2412, 2417, 2427MHz 2450MHz within 50MHz of calibration frequency 6.94 12.0% 5260, 5300MHz 5300MHz within 110MHz of calibration frequency 4.77 13.1% 5680MHz 5600MHz within 110MHz of calibration frequency 4.42 13.1% 5745, 5805MHz 5800MHz within 110MHz of calibration frequency 4.41 13.1% *. The uncertainty is the RSS of the ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band. *a. The target value is a parameter defined in Appendix A of KDB865664 D01, the dielectric parameters suggested for head and body tissue simulating liquid are given at 2000, 2450, 3000 and 5800MHz. Parameters for the frequencies 2000-3000, 3000-5800MHz were obtained using linear interpolation, for above 5800MHz were obtained using linear extrapolation (Refer to appendix 3-4.) *b. Refer to KDB865664 D01, item 2), Clause 2.6; "When nominal tissue dielectric parameters are recorded in the probe calibration data; for example, only target values and tolerance are reported, the measured εr and σ of the liquid used in routine measurements must be: (for 2.4GHz band) ≤ the target εr and ≥ the target σ values and also within 5% of the required target dielectric parameters." (for 5GHz band) must be: within +5% and -10% of the target εr, and also within -5% and +10% of the target σ values, when the measured SAR is compensated for tissue dielectric deviations." Since SAR correction value becomes smaller than measured value, compensation is not carried out. *c. The coefficients are parameters defined in clause E.3.3.2, IEEE Std 1528(2013). Since the measured liquid parameters were  the target εr and  the target  values and also within 5% of the required target dielectric parameters, the measured SAR was not compensated by ΔSAR coefficients (*. Clause 2) of 2.6, KDB865664 D01). ΔSAR(1g)= Cεr Δεr + C Δ, Cεr=-7.854E-4f3+9.402E-3f2-2.742E-2f-0.2026 / C =9.804E-3f3-8.661E-2f2+2.981E-2f+0.7829 *d. Tuned-up SAR by scaled factor: Accordance with KDB 447498 D01; "When SAR is not measured at the maximum power level allowed for production units, the results must be scaled to the maximum tune-up tolerance limit according to the power applied to the individual channels tested to determine compliance (clause 4, 4.1, 4)". *. Calculating formula: SAR corrected SAR (1g) (W/kg) = (Observed SAR(1g) (W/kg))  (100 - (SAR(%)) / 100 Reported SAR(1g) (=Tuned-up SAR) (W/kg) = (Observed SAR(1g) (W/kg))  (Scaled factor) UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 / Facsimile: +81 463 50 6401


Document Created: 2014-12-12 18:52:29
Document Modified: 2014-12-12 18:52:29
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC