FCC Report_DFS

FCC ID: W2Z-01000006

Test Report

Download: PDF
FCCID_2473652

Test report No. : 103156985—G Page : 1 of 23 Issued date : October 28, 2014 Revised date : December 12, 2014 FCC ID : W2Z—01000006 RADIO TEST REPORT Test Report No. : 103156988—G Applicant f FUJIFILM Corporation Type of Equipment f Flat Panel Sensor Model No. f DR—ID1201SE FCC ID f Ww27—01000006 Test regulation f FCC Part 15 Subpart E: 2014 (DFS test only) Test result f Complied 1. This test report shall not be reproduced in full or partial, without the written approval of UL Japan, Inc. 2. The results in this report apply only to the sample tested. 3. This sample tested is in compliance with the limits of the above regulation. 4. The test results in this test report are traceable to the national or international standards. 5. This test report must not be used by the customer to claim product certification, approval, or endorsement by any agency ofthe Federal Government. 6. The opinions and the interpretations to the result of the description in this report are outside scopes where Japan has been accredited. Date of test ave of tes September 22, 2014 Representative test engineer: JM Tatsuya _ Arai Engineer Consumer Technology Division Approved is : /?/%m( Toyokazu Imamura Leader Consumer Technology Division ”’u/gu\“ w LW 8 x." f/ s LAB Bz/’/A e\ I1 \\\‘ JAB Testing RTLO261 |:| The testing in which "Non—accreditation"is displayed is outside the accreditation scopes in UL Japan. nzein E There is no testing item of "Non—accreditation". UL Japan, Inc. Shonan EMC Lab. 1—22—3 Megumigaoka, Hiratsuka—shi, Kanagawa—ken, 259—1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401 13—EM—FO429

Test report No. : 10315698S-G Page : 2 of 23 Issued date : October 28, 2014 Revised date : December 12, 2014 FCC ID : W2Z-01000006 REVISION HISTORY Original Test Report No.: 10315698S-G Revision Test report No. Date Page revised Contents - (Original) 10315698S-G October 28, 2014 - - 1 10315698S-G December 12, 2014 4 Correction of Rating UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401

Test report No. : 10315698S-G Page : 3 of 23 Issued date : October 28, 2014 FCC ID : W2Z-01000006 CONTENTS PAGE SECTION 1: Customer information......................................................................................... 4 SECTION 2: Equipment under test (E.U.T.) ........................................................................... 4 SECTION 3: Scope of Report ................................................................................................... 5 SECTION 4: Test specification, procedures & results............................................................. 5 SECTION 5: Operation of E.U.T. during testing..................................................................... 10 SECTION 6: In-Service Monitoring for Channel Move Time, Channel Closing Transmission Time ............................................................................................................................................ 16 SECTION 7: In-Service Monitoring for Non-Occupancy Period............................................ 19 APPENDIX 1: Data of DFS test ................................................................................................. 21 APPENDIX 2: Test instruments ................................................................................................ 22 APPENDIX 3: Photographs of test setup .................................................................................. 23 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401

Test report No. : 10315698S-G Page : 4 of 23 Issued date : October 28, 2014 Revised date : December 12, 2014 FCC ID : W2Z-01000006 SECTION 1: Customer information Company Name : FUJIFILM Corporation Address : 2-26-30 Nishiazabu Minatoku Tokyo 106-8620, Japan Telephone Number : 81-3-6271-1975 Facsimile Number : 81-3-6271-1189 Contact Person : Mitsuyuki Komiya SECTION 2: Equipment under test (E.U.T.) 2.1 Identification of E.U.T. Type of Equipment : Flat Panel Sensor Model Number : DR-ID1201SE Serial Number : Refer to Section 5.2 Rating : DC 8V(Battery) Country of Mass-production : Japan Condition of EUT : Engineering prototype (Not for Sale: This sample is equivalent to mass-produced items.) Receipt Date of Sample : September 9, 2014 Modification of EUT : The test lab did not make the modification to the EUT supplied from the customer to have it pass the tests. 2.2 Product description Model: DR-ID1201SE (referred to as the EUT in this report) is Flat Panel Sensor. General specification: Clock frequency(ies) in the system : 40MHz Radio specification: Radio Type : Transceiver Method of Frequency Generation : Synthesizer Power Supply (inner) : DC3.3V IEEE802.11b IEEE802.11g IEEE802.11a IEEE802.11n IEEE802.11n (20M band) (40M band) Frequency 2412-2462MHz 2412-2462MHz 5180-5320MHz 2412-2462MHz 2422-2452MHz of operation 5500-5700MHz 5180-5320MHz 5190-5310MHz 5745-5825MHz 5500-5700MHz 5510-5670MHz 5745-5825MHz 5755-5795MHz Type of modulation DSSS OFDM-CCK OFDM (CCK, DQPSK, (64QAM, 16QAM, (64QAM, 16QAM, QPSK, BPSK) DBPSK) QPSK, BPSK) Channel spacing 5MHz 20MHz 2.4GHz band 2.4GHz band 5MHz 5MHz 5GHz band 5GHz band 20MHz 40MHz Antenna Antenna #1 (Bottom) Antenna #0 (Side) 2 pcs. (*. Separation distance between the antenna 1 and the antenna: 417mm ) Antenna quantity 11b,g,a: One selected Tx antenna operation. 11n(20HT),n(40HT): One selected Tx antenna operation (MCS0~7) / Two Tx antenna operation (MCS8~13) Antenna model 113Y120035A (cable length: 300mm) 113Y1200036A (cable length: 575mm) Antenna type / connector Monopole antenna / Connector; PCB side: U.FL, Antenna side: soldered type Antenna gain (max.peak) -5.1 dBi (2.4GHz), -6.9 dBi (2.4GHz) (excluding cable loss) -1.3 dBi (5GHz) -1.8 dBi (5GHz) UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401

Test report No. : 10315698S-G Page : 5 of 23 Issued date : October 28, 2014 FCC ID : W2Z-01000006 FCC 15.31 (e) The EUT is a battery-operated device and test was performed with the full-charged battery. Therefore, the EUT complies with the requirement. FCC 15.203 It is impossible for end users to replace the antenna, because the antenna is mounted inside of the EUT. Therefore the EUT complies with the requirement. SECTION 3: Scope of Report The EUT has the channels from 5180 to 5320MHz and 5500 to 5700MHz. This report only covers DFS requirement subject to 5250-5350MHz and 5500 to 5700MHz bands, as specified by the following referenced procedures. SECTION 4: Test specification, procedures & results 4.1 Test Specification Test Specification : FCC Part 15 Subpart E: 2014, final revised on August 15, 2014 and effective October 14, 2014 Title : FCC 47CFR Part15 Radio Frequency Device Subpart E Unlicensed National Information Infrastructure Devices Section 15.407 General technical requirements * The revision on August 15, 2014 does not affect the test specification applied to the EUT. Test Specification : KDB905462 D02 UNII DFS Compliance Procedures New Rules v01r01 Title : COMPLIANCE MEASUREMENT PROCEDURES FOR UNLICENSED- NATIONAL INFORMATION INFRASTRUCTURE DEVICES OPERATING IN THE 5250-5350MHz AND 5470-5725MHz BANDS INCORPORATING DYNAMIC FREQUENCY SELECTION Test Specification : KDB905462 D03 Client Without DFS New Rules v01r01 Title : U-NII CLIENT DEVICES WITHOUT RADAR DETECTION CAPABILITY UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401

Test report No. : 10315698S-G Page : 6 of 23 Issued date : October 28, 2014 FCC ID : W2Z-01000006 4.2 Procedures and results Table 2: Applicability of DFS Requirements Requirement Operating Mode Test Procedures & Deviation Results Client without Limits Radar Detection U-NII Detection Not required FCC, KDB 905462 D02 N/A N/A Bandwidth Section 7.8.1 Initial Channel Not required FCC15.407 (h)(2) N/A N/A Availability Check FCC, KDB 905462 D02 Time Section 7.8.2.1 RSS-210 A9.3 Radar Burst at the Not required FCC15.407 (h)(2) N/A N/A Beginning of the FCC, KDB 905462 D02 Channel Availability Section 7.8.2.2 Check Time RSS-210 A9.3 Radar Burst at the Not required FCC15.407 (h)(2) N/A N/A End of the Channel FCC, KDB 905462 D02 Availability Check Section 7.8.2.3 Time RSS-210 A9.3 In-Service Monitoring Yes FCC15.407 (h)(2) N/A Complied for Channel Move FCC, KDB 905462 D02 Time, Channel Section 7.8.3 Closing Transmission Time RSS-210 A9.3 In-Service Monitoring Yes * FCC15.407 (h)(2) N/A Complied for Non-Occupancy FCC, KDB 905462 D02 period Section 7.8.3 RSS-210 A9.3 Statistical Not required FCC15.407 (h)(2) N/A N/A Performance Check FCC, KDB 905462 D02 Section 7.8.4 *Although this test was not required in FCC, KDB 905462 D02, it was performed as additional test. Table 3: DFS Detection Thresholds for Master Devices and Client Devices With Radar Maximum Transmit Power Value (See Notes 1, 2 and 3) E.I.R.P. ≥ 200 milliwatt -64 dBm E.I.R.P. < 200 milliwatt and -62 dBm power spectral density < 10dBm/MHz E.I.R.P. < 200 milliwatt that do not meet the power -64 dBm spectral density requirement Note 1: This is the level at the input of the receiver assuming a 0 dBi receive antenna. Note 2: Throughout these test procedures an additional 1 dB has been added to the amplitude of the test transmission waveforms to account for variations in measurement equipment. This will ensure that the test signal is at or above the detection threshold level to trigger a DFS response. Note 3: E.I.R.P. is based on the highest antenna gain. For MIMO devices refer to KDB Publication 662911 D01. UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401

Test report No. : 10315698S-G Page : 7 of 23 Issued date : October 28, 2014 FCC ID : W2Z-01000006 Table 4 DFS Response Requirement Values Parameter Value Non-occupancy period Minimum 30 minutes Channel Availability Check Time 60 seconds Channel Move Time 10 seconds See Note 1 Channel Closing Transmission Time 200 milliseconds + an aggregate of 60 milliseconds over remaining 10 second period. See Notes 1 and 2 U-NII Detection Bandwidth Minimum 100% of the U-NII 99% transmission power bandwidth See Note 3 Note 1: The Channel Move Time and the Channel Closing Transmission Time should be performed with Radar Type 0. The measurement timing begins at the end of the Radar Type 0 burst. Note 2: The Channel Closing Transmission Time is comprised of 200 milliseconds starting at the beginning of the Channel Move Time plus any additional intermittent control signals required to facilitate a Channel move (an aggregate of 60 milliseconds) during the remainder of the 10 second period. The aggregate duration of control signal will not count quiet periods in between transmissions. Note 3: During the U-NII Detection Bandwidth detection test, radar type 0 should be used. For each frequency step the minimum percentage of detection is 90 percent. Measurements are performed with no data traffic. Table 5 Short Pulse Radar Test Waveform Radar Type Pulse Width PRI Number of Pulses Minimum Minimum (µsec) (µsec) Percentage of Number of Successful Traials Detection 0 1 1428 18 See Note 1 See Note 1 1 1 Test A: 15 unique Roundup ( 60% 30 PRI values (1 / 360) randomly selected x ( (19 x 10^6 ) from the list of 23 / PRI [micro sec.] PRI values in )) Table 5a Test B: 15 unique PRI values randomly selected within the range of 518-3066 micro sec., with a minimum increment of 1 micro sec., excluding PRI values selected in Test A 2 1-5 150-230 23-29 60% 30 3 6-10 200-500 16-18 60% 30 4 11-20 200-500 12-16 60% 30 Aggregate (Rader Types 1-4) 80% 120 Note 1: Short Pulse Radar Type 0 should be used for the detection bandwidth test, channel move time, and channel closing time tests. UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401

Test report No. : 10315698S-G Page : 8 of 23 Issued date : October 28, 2014 FCC ID : W2Z-01000006 Table 5a Pulse Repetition Interval Values for Test A Pulse Repetition Pulse Repetition Frequency Pulse Repetition Interval Frequency Number (Pulses Per Second) (Micro seconds) 1 1930.5 518 2 1858.7 538 3 1792.1 558 4 1730.1 578 5 1672.2 598 6 1618.1 618 7 1567.4 638 8 1519.8 658 9 1474.9 678 10 1432.7 698 11 1392.8 718 12 1355 738 13 1319.3 758 14 1285.3 778 15 1253.1 798 16 1222.5 818 17 1193.3 838 18 1165.6 858 19 1139 878 20 1113.6 898 21 1089.3 918 22 1066.1 938 23 326.2 3066 Table 6 Long Pulse Radar Test Waveform Radar Type Pulse Width Chip Width PRI (µsec) Number of Number of Minimum Minimum (µsec) (MHz) Pulses per Burst Percentage Number of Burst of Successful Trials Detection 5 50-100 5-20 1000-2000 1-3 8-20 80% 30 Table 7 Frequency Hopping Radar Test Waveform Radar Type Pulse Width PRI (µsec) Pulse per Hopping Hopping Minimum Minimum (µsec) Hop (kHz) Rate (kHz) Sequence Percentage Number of Length of Successful Trials (msec) Detection 6 1 333 9 0.333 300 70% 30 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401

Test report No. : 10315698S-G Page : 9 of 23 Issued date : October 28, 2014 FCC ID : W2Z-01000006 4.3 Test Location UL Japan, Inc. Shonan EMC Lab. 1-22-3, Megumigaoka, Hiratsuka-shi, Kanagawa-ken 259-1220 JAPAN Telephone number : +81 463 50 6400 Facsimile number : +81 463 50 6401 Size of reference IC Maximum Width x Depth x ground plane (m) / Registration measurement Height (m) horizontal No. distance conducting plane No.1 Semi-anechoic chamber 2973D-1 20.6 x 11.3 x 7.65 20.6 x 11.3 10m No.2 Semi-anechoic chamber 2973D-2 20.6 x 11.3 x 7.65 20.6 x 11.3 10m No.3 Semi-anechoic chamber 2973D-3 12.7 x 7.7 x 5.35 12.7 x 7.7 5m No.4 Semi-anechoic chamber - 8.1 x 5.1 x 3.55 8.1 x 5.1 - No.1 Shielded room - 6.8 x 4.1 x 2.7 6.8 x 4.1 - No.2 Shielded room - 6.8 x 4.1 x 2.7 6.8 x 4.1 - No.3 Shielded room - 6.3 x 4.7 x 2.7 6.3 x 4.7 - No.4 Shielded room - 4.4 x 4.7 x 2.7 4.4 x 4.7 - No.5 Shielded room - 7.8 x 6.4 x 2.7 7.8 x 6.4 - No.6 Shielded room - 7.8 x 6.4 x 2.7 7.8 x 6.4 - No.1 Measurement room - 2.55 x 4.1 x 2.5 - - 4.4 Uncertainty The following uncertainties have been calculated to provide a confidence level of 95% using a coverage factor k=2. Time Measurement uncertainty for this test was: (±) 0.012% 4.5 Test set up, Data of DFS test, and Test instruments of DFS Refer to APPENDIX. UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401

Test report No. : 10315698S-G Page : 10 of 23 Issued date : October 28, 2014 FCC ID : W2Z-01000006 SECTION 5: Operation of E.U.T. during testing 5.1 Operating Modes The EUT, which is a Client Device without Radar detection capability, operates over the 5260-5320MHz and 5500- 5700MHz. Power level of the EUT [dBm] Antenna Band Output Power (Min) Output Power(Max) Monopole Antenna *1) W53 10.77 14.88 W56 11.56 17.10 *1) Refer to 10315698S-F FCC Part 15E (FCC 15.407) report for other parts than DFS. WLAN traffic is generated by the software to ping from the Master to the Client. That software has random ping intervals. (Channel loading was over 17%) Software name & version: ExPing Version 1.33 The EUT utilizes the 802.11a and 802.11n architecture, with a nominal channel bandwidth. The EUT had used IEEE 802.11n (HT40) (widest mode) . The FCC ID for the Master Device used with EUT for DFS testing is LDK102073. The rated output power of the Master unit is >200mW(23dBm). Therefore the required interference threshold level is – 64 dBm. After correction for antenna gain and procedural adjustments, the required conducted threshold at the antenna port is –64 + 1 + 3.5=-59.5 dBm (threshold level + additional 1dB + antenna gain). It is impossible for users to change DFS control, because the DFS function is written on the firmware and users cannot access it. UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401

Test report No. : 10315698S-G Page : 11 of 23 Issued date : October 28, 2014 FCC ID : W2Z-01000006 5.2 Configuration and peripherals Conducted 4 B A method C E system 2 5 D F 3 6 AC100V/50Hz : Standard Ferrite Core Description of EUT and Support equipment No. Item Model number Serial number Manufacturer Remarks Wireless LAN board SX-PCEAN(FF) 00809261B110 Silex EUT A *1) B Flat Panel Sensor DR-ID 613SE *2) E321154 Fujifilm - Wireless LAN access AIR-AP1262N-A-K9 FTX1619E5EZ Cisco Systems FCC ID: C point (Master Device) LDK102073 D AC Adapter EADP-18MB DAB1528MANP Cisco Systems - E Notebook Computer DELL Vostro V1510 29090510205 Dell - F AC Adaptor LA65NS1-00 71615-93B-385D Dell - *1) This board is installed DR-ID1201SE. *2) It was used to operate the Wireless LAN board. List of cables used No. Cable Name Length (m) Shield Cable Connector 2 Access Point DC Power 1.8 Unshielded Unshielded 3 Access Point AC Power 2.0 Unshielded Unshielded 4 LAN 3.0 Unshielded Unshielded 5 DELL PC DC Power 1.8 Unshielded Unshielded 6 DELL PC AC Power 0.7 Unshielded Unshielded UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401

Test report No. : 10315698S-G Page : 12 of 23 Issued date : October 28, 2014 FCC ID : W2Z-01000006 5.3 Test and Measurement System SYSTEM OVERVIEW The measurement system is based on a conducted test method. The software selects waveform parameters from within the bounds of the signal type on a random basis using uniform distribution. The short pulse types 2, 3, and 4, the long pulse type 5, and the frequency hopping type 6 parameters are randomized at run-time. The signal monitoring equipment consists of a spectrum analyzer with the capacity to display 8001 bins on the horizontal axis. A time-domain resolution of 2 msec/bin is achievable with a 16 second sweep time, meeting the 10 seconds short pulse reporting criteria. The aggregate ON time is calculated by multiplying the number of bins above a threshold during a particular observation period by the dwell time per bin, with the analyzer set to peak detection. A time-domain resolution of 3 msec/bin is achievable with a 24 second sweep time, meeting the 22 second long pulse reporting criteria and allowing a minimum of 10 seconds after the end of the long pulse waveform. FREQUENCY HOPPING RADAR WAVEFORM GENERATING SUBSYSTEM The first 100 frequencies are selected out of the hopping sequence of the randomized 475 hop frequencies. Only a Burst that has the frequency falling within the receiver bandwidth of the tested U-NII device is selected among those frequencies. (Frequency-domain simulation). The radar waveform generated at the start time of the selected Burst (Time-domain simulation) is download to the Signal Generator. If all of the randomly selected 100 frequencies do not fall within the receiver bandwidth of the U-NII device, the radar waveform is not used for the test. CONDUCTED METHODS SYSTEM BLOCK DIAGRM To Spectrum Analyzer 10MHz out Signal Generator Notebook Computer See Page 11 PowerDivider Power DC to 26.5GHz Splitters/ Attenuator Attenuator A Combiners (20dB) (20dB) D: See Page 11 B Attenuator (20dB) Master C A: Power EUT Splitters/ Combiners (Client) Spectrum Analyzer From Signal Generator 10MHz in MEASUREMENT SYSTEM FREQUENCY REFERENCE Lock the signal generator and the spectrum analyzer to the same reference sources as follows: Connect the 10MHz OUT on the signal generator to the 10MHz IN on the spectrum analyzer and set the spectrum analyzer 10MHz In to On. UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401

Test report No. : 10315698S-G Page : 13 of 23 Issued date : October 28, 2014 FCC ID : W2Z-01000006 SYSTEM CALIBRATION Step 1: Set the system as shown in Figure 3 of FCC, KDB 905462 Section 7.2.2. Step 2: Adjust each attenuator to fulfill the following three conditions: - WLAN can be communicated, and - Rader detection threshold level is bigger than Client Device traffic level on the spectrum analyzer, and - Master Device traffic level is not displayed on the spectrum analyzer. Step 3: Terminate 50 ohm at B and C points, and connect the spectrum analyzer to the point A. (See the figure on page 12) At the point A, adjust the signal generator and spectrum analyzer to the center frequency of the channel to be measured. Download the applicable radar waveforms to the signal generator. Select the radar waveform, trigger a burst manually and measure the amplitude on the spectrum analyzer. Readjust the amplitude of the signal generator as required so that the peak level of the waveform is at a displayed level equal to the required or desired interference detection threshold. Separate signal generator amplitude settings are determined as required for each radar type. Step 4: Without changing any of the instrument settings, restore the system setting to Step 2 and adjust the Reference Level Offset of the spectrum analyzer to the level at Step 3. By taking the above steps 1 to 4, the spectrum analyzer displays the level of the signal generator as received at the antenna ports of the Master Device. See Clause 5.4 for Plots of Noise, Rader Waveforms, and WLAN signals. 5.4 Plots of Noise, Rader Waveforms, and WLAN signals Plots of System Noise Floor (for 11n (HT40), 5310MHz) It was confirmed that the EUT did not transmit before having received appropriate control signals from a Master Device. UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401

Test report No. : 10315698S-G Page : 14 of 23 Issued date : October 28, 2014 FCC ID : W2Z-01000006 Plots of Radar Waveforms (for 11n (HT40), 5310MHz) Rader Type 1 (for 11n (HT40), 5310MHz) Rader Type 5 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401

lal ® lt _ A

Test report No. : 10315698S-G Page : 16 of 23 Issued date : October 28, 2014 FCC ID : W2Z-01000006 SECTION 6: In-Service Monitoring for Channel Move Time, Channel Closing Transmission Time 6.1 Operating environment Test place : No.5 Shielded Room Temperature : 26 deg.C Humidity : 43 %RH 6.2 Test Procedure Transfer files from the Master Device to the Client Device on the tested channel during the entire period of the test. The Radar Waveform generator sends a Burst of pulses for one of the Short Pulse Radar Types 0-4 at levels defined , on the Operating Channel. An additional 1 dB is added to the radar test signal to ensure it is at or above the DFS Detection Threshold, accounting for equipment variations/errors. Observe the transmissions of the EUT at the end of the radar Burst on the Operating Channel for duration greater than 10 seconds. 6.3 Test data (for 11n (HT40), 5310MHz) Test Item Unit Measurement Time Limit Results Channel Move Time *1) [sec] 1.790 10.000 Pass Channel Closing Transmission Time *2) [msec] 20 60 Pass *1) Channel Move Time is calculated as follows: (Channel Move Time) = (End of Transmission) - (End of Burst) = 2.976 – 1.186 *2) Channel Closing Transmission Time is calculated from (End of Burst + 200msec) to (End of Burst + 10sec ) (Channel Closing Transmission Time) = (Number of analyzer bins showing transmission)＊(dwell time per bin) = 10 x 2 (msec) UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401

Test report No. : 10315698S-G Page : 17 of 23 Issued date : October 28, 2014 FCC ID : W2Z-01000006 (for 11n (HT40), 5310MHz) Radar Type 1 Marker 1: - End of Burst : 1.186 s Marker 2: - End of Transmission : 2.976 s End of Burst End of Transmission UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401

Test report No. : 10315698S-G Page : 18 of 23 Issued date : October 28, 2014 FCC ID : W2Z-01000006 (for 11n (HT40), 5310MHz) Radar Type 5 Marker 1 : End of Burst : 12710 ms Marker 2 : End of Transmission : 13810ms 6.4 Test result Test result: Pass Date : September 22, 2014 Test engineer : Tatsuya Arai UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401

Test report No. : 10315698S-G Page : 19 of 23 Issued date : October 28, 2014 FCC ID : W2Z-01000006 SECTION 7: In-Service Monitoring for Non-Occupancy Period 7.1 Operating environment Test place : No.5 Shielded Room Temperature : 26 deg.C Humidity : 43 %RH 7.2 Test Procedure The following two tests are performed: 1). Transfer files from the Master Device to the Client Device on the tested channel during the entire period of the test. The Radar Waveform generator sends a Burst of pulses for one of the Radar Types 0-6 at levels defined on the Operating Channel. An additional 1 dB is added to the radar test signal to ensure it is at or above the DFS Detection Threshold, accounting for equipment variations/errors. Observe the transmissions of the EUT after the Channel Move Time on the Operating Channel for duration greater than 30 minutes. 2). Transfer files from the Master Device to the Client Device on the tested channel during the entire period of the test. Observe the transmissions of the EUT on the Operating Channel for duration greater than 30 minutes after the Master Device is shut off. 7.3 Test data (for 11n (HT40), 5310MHz) 1).Radar Type 1 Marker 1 : End of Burst : 19.92 sec Marker 2 : End of Burst +10sec : 29.92 sec UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401

Test report No. : 10315698S-G Page : 20 of 23 Issued date : October 28, 2014 FCC ID : W2Z-01000006 2).Master is shut off (for 11n (HT40), 5310MHz) Marker 1 : End of transmission : 24.96 sec 7.4 Test result Test result: Pass Date : September 22, 2014 Test engineer : Tatsuya Arai UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401

Test report No. : 10315698S-G Page : 21 of 23 Issued date : October 28, 2014 FCC ID : W2Z-01000006 APPENDIX 1: Data of DFS test Parameter Data for Radar Type 5 Trial Number of Pulse Chirp Pulse 1-to-2 Pulse 2-to-3 Starting Location Burst Number Pulses Width (usec) Width (MHz) Spacing (usec) Spacing (usec) Within Interval (usec) 1 1 1 52 8 64 1 2 2 94 7 1535 680793 1 3 3 67 8 1851 1146 452538 1 4 1 50 18 791967 1 5 3 82 14 1511 1064 61930 1 6 2 98 12 1125 95345 1 7 1 76 6 434356 1 8 1 64 16 720311 1 9 1 79 13 728383 1 10 1 61 15 194181 1 11 3 73 16 1638 1497 569650 1 12 2 95 11 1811 434312 1 13 2 50 19 1491 613325 1 14 3 58 13 1254 1098 431579 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401

Test report No. : 10315698S-G Page : 22 of 23 Issued date : October 28, 2014 FCC ID : W2Z-01000006 APPENDIX 2: Test instruments EMI Test Equipment The expiration date of the calibration is the end of the expired month. As for some calibrations performed after the tested dates, those test equipment have been controlled by means of an unbroken chains of calibrations. All equipment is calibrated with valid calibrations. Each measurement data is traceable to the national or international standards. Test Item： DFS: Dynamic Frequency Selection UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone: +81 463 50 6400 Facsimile: +81 463 50 6401


Document Created: 2014-12-12 11:34:20
Document Modified: 2014-12-12 11:34:20
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC