Test Report WCDMA

FCC ID: VUJ-AT312

Test Report

Download: PDF
FCCID_3071440

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E FCC PART 22/24 TEST REPORT FCC Part 22 /Part 24 Report Reference No. .................... : LCS1607050245E FCC ID. ............................................ : VUJ-AT312 Date of Issue. ................................. : July 02, 2016 Testing Laboratory Name .............. : Shenzhen LCS Compliance Testing Laboratory Ltd. 1/F., Xingyuan Industrial Park, Tongda Road, Bao'an Avenue, Bao'an Address............................................. : District, Shenzhen, Guangdong, China Applicant’s name ............................ : ATID Co., Ltd (Gasan-dong, #1210 Byuksan/Kyungin Digitalvalley, II), 184, Address............................................. : Gasandigital2-ro, Geumcheon-gu, Seoul, South Korea, 153-803 Test specification .......................... : FCC Part 22: PUBLIC MOBILE SERVICES Standard ........................................... : FCC Part 24: PERSONAL COMMUNICATIONS SERVICES Test Report Form No ....................... : LCSEMC-1.0 TRF Originator .................................. : Shenzhen LCS Compliance Testing Laboratory Ltd. Master TRF ....................................... : Dated 2011-03 Shenzhen LCS Compliance Testing Laboratory Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description .....................: 3G Smart phone Trade Mark ....................................... : Model/Type reference....................... : AT312 Listed Models .................................. : P60-B Ratings.............................................. : DC 3.70V Modulation ....................................... : QPSK Hardware version ............................. : T09B-00-1107 Software version .............................. : V 2.2 Frequency .......................................... UMTS Band II /UMTS Band V Result................................................ : PASS Compiled by: Supervised by: Approved by: Jacky Li/ File administrators Glin Lu/ Technique principal Gavin Liang/ Manager This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E TEST REPORT July 02, 2016 Test Report No. : LCS1607050245E ______________________________________________________________________________________________ Date of issue Equipment under Test : 3G Smart phone Model /Type : AT312 Listed Models : P60-B Applicant : ATID Co., Ltd Address : (Gasan-dong, #1210 Byuksan/Kyungin Digitalvalley, II), 184, Gasandigital2-ro, Geumcheon-gu, Seoul, South Korea, 153-803 Manufacturer : Shenzhen BoRui Technology Co.,Ltd Address : Room 1502, Unit B3,Kexing Science Park, No.5 Keyuan Road, Middle district of Hi-tech Park, Nanshan District, Shenzhen, China. Factory : Shenzhen BoRui Technology Co.,Ltd Address : Room 1502, Unit B3,Kexing Science Park, No.5 Keyuan Road, Middle district of Hi-tech Park, Nanshan District, Shenzhen, China. Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E Revison History Revision Issue Date Revisions Revised By 00 2016-07-02 Initial Issue Gavin Liang This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E Contents 1 TEST STANDARDS .................................................................. 5 2 SUMMARY ............................................................................. 6 2.1 General Remarks 6 2.2 Product Description 6 2.3 Equipment under Test 7 2.4 Short description of the Equipment under Test (EUT) 7 2.5 Internal Identification of AE used during the test 7 2.6 Normal Accessory setting 7 2.7 EUT configuration 8 2.8 Related Submittal(s) / Grant (s) 8 2.9 Modifications 8 2.10 General Test Conditions/Configurations 8 3 TEST ENVIRONMENT............................................................... 9 3.1 Address of the test laboratory 9 3.2 Test Facility 9 3.3 Environmental conditions 9 3.4 Test Description 9 3.5 Equipments Used during the Test 11 3.6 Measurement uncertainty 12 4 TEST CONDITIONS AND RESULTS ............................................ 13 4.1 Output Power 13 4.2 Radiated Spurious Emssion 17 4.3 Occupied Bandwidth and Emission Bandwith 20 4.4 Band Edge Compliance 22 4.5 Spurious Emssion on Antenna Port 24 4.6 Frequency Stability Test 28 4.7 Peak-to-Average Ratio (PAR) 30 5 TEST SETUP PHOTOS OF THE EUT .......................................... 32 6 EXTERNAL PHOTOS OF THE EUT ............................................. 32 7 INTERNAL PHOTOS OF THE EUT.............................................. 32 This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E 1 TEST STANDARDS The tests were performed according to following standards: FCC Part 22 (10-1-16 Edition): PRIVATE LAND MOBILE RADIO SERVICES. FCC Part 24(10-1-16 Edition): PUBLIC MOBILE SERVICES TIA/EIA 603 D June 2010: Land Mobile FM or PM Communications Equipment Measurement and Performance Standards. 47 CFR FCC Part 15 Subpart B: - Unintentional Radiators FCC Part 2: FREQUENCY ALLOCA-TIONS AND RADIO TREATY MAT-TERS; GENERAL RULES AND REG-ULATIONS ANSI C63.4:2014: Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz FCCKDB971168D01 Power Meas License Digital Systems This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E 2 SUMMARY 2.1 General Remarks Date of receipt of test sample : June. 13, 2016 Testing commenced on : July 02, 2016 Testing concluded on : July 02, 2016 2.2 Product Description The ATID Co., Ltd’s Model: AT312 or the “EUT” as referred to in this report; more general information as follows, for more details, refer to the user’s manual of the EUT. Name of EUT 3G Smart phone Model Number AT312, P60-B PCB board, structure and internal of these model(s) are the same, So Model Declaration no additional models were tested Test Model AT312 Hardware version T09B-00-1107 Software version V 2.2 Android version 5.1 GSM/EDGE/GPRS Operation GSM850/PCS1900/GPRS850/GPRS1900/EDGE850/EDGE1900 Frequency Band UMTS Operation Frequency Band UMTS FDD Band II/V GSM/EDGE/GPRS Supported GSM/GPRS/EDGE GSM Release Version R99 GSM/EDGE/GPRS Power Class GSM850:Power Class 4/ PCS1900:Power Class 1 GPRS/EDGE Multislot Class GPRS/EDGE: Multi-slot Class 12 GPRS operation mode Class B WCDMA Release Version R99 HSDPA Release Version Release 10 HSUPA Release Version Release 6 DC-HSUPA Release Version Not Supported WLAN Supported 802.11b/802.11g/802.11n GSM/UMTS Modulation Type GMSK for GSM/GPRS, 8-PSK for EDGE,QPSK for UMTS IEEE 802.11b:2412-2462MHz IEEE 802.11g:2412-2462MHz WLAN FCC Operation frequency IEEE 802.11n HT20:2412-2462MHz IEEE 802.11n HT40:2422-2452MHz IEEE 802.11b: DSSS(CCK,DQPSK,DBPSK) IEEE 802.11g: OFDM(64QAM, 16QAM, QPSK, BPSK) WLAN FCC Modulation Type IEEE 802.11n HT20: OFDM (64QAM, 16QAM, QPSK,BPSK) IEEE 802.11n HT40: OFDM (64QAM, 16QAM, QPSK,BPSK) Bluetooth Supported BT 4.0/BT 3.0+EDR Bluetooth Operation frequency 2402MHz-2480MHz Bluetooth Modulation Type GFSK,π/4DQPSK, 8DPSK GPS function Supported and only RX Antenna Type PIFA Antenna 1.0dBi (max.) For GSM 850; 1.2dBi (max.) For PCS 1900; Antenna Gain 1.2dBi (max.) For WCDMA Band II 1.0dBi (max.) For WCDMA Band V 1.0 dBi (max.) For WIFI/BT Extreme temp. Tolerance -30°C to +50°C Extreme vol. Limits 3.40VDC to 4.20VDC (nominal: 3.70VDC) This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E 2.3 Equipment under Test Power supply system utilised Power supply voltage : ○ 120V / 60 Hz ○ 115V / 60Hz ○ 12 V DC ○ 24 V DC ● Other (specified in blank below) DC 3.70V Test frequency list RF Channel Test Mode TX/RX Low(L) Middle (M) High (H) Channel 4132 Channel 4183 Channel 4233 TX 826.4 MHz 836.6 MHz 846.6 MHz WCDMA Band V Channel 4357 Channel 4407 Channel 4458 RX 871.4 MHz 881.4 MHz 891.6 MHz RF Channel Test Mode TX/RX Low(L) Middle (M) High (H) Channel 9262 Channel 9400 Channel 9538 TX 1852.4 MHz 1880.0 MHz 1907.6 MHz WCDMA Band II Channel 9662 Channel 9800 Channel 9938 RX 1932.4 MHz 1960.0 MHz 1987.6 MHz 2.4 Short description of the Equipment under Test (EUT) 2.4.1 General Description AT312 is subscriber equipment in the WCDMA/GSM system. The HSPA/UMTS frequency band is Band II/V; The GSM/GPRS/EDGE frequency band includes GSM850 and GSM900 and DCS1800 and PCS1900, but only Band II and Band V and GSM850 and PCS1900 bands test data included in this report. The 3G Smart Phone implements such functions as RF signal receiving/transmitting, HSPA/UMTS ,LTE and GSM/GPRS/EDGE protocol processing, voice, video MMS service, GPS and WIFI etc. Externally it provides micro SD card interface, earphone port (to provide voice service) and SIM card interface. It also provides Bluetooth module to synchronize data between a PC and the phone, or to use the built-in modem of the phone to access the Internet with a PC, or to exchange data with other Bluetooth devices. NOTE: Unless otherwise noted in the report, the functional boards installed in the units shall be selected from the below list, but not means all the functional boards listed below shall be installed in one unit. 2.5 Internal Identification of AE used during the test AE ID* Description AE1 Charger AE1 Model: ZHY-NU050100M INPUT: AC100-240V 50/60Hz 200mA OUTPUT: DC 5.0V 1.0A *AE ID: is used to identify the test sample in the lab internally. 2.6 Normal Accessory setting Fully charged battery was used during the test. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E 2.7 EUT configuration The following peripheral devices and interface cables were connected during the measurement: ● - supplied by the manufacturer ○ - supplied by the lab ○ Power Cable Length (m) : / Shield : / Detachable : / ○ Multimeter Manufacturer : / Model No. : / 2.8 Related Submittal(s) / Grant (s) This submittal(s) (test report) is intended for FCC ID: VUJ-AT312 filing to comply with FCC Part 22 and Part 24. 2.9 Modifications No modifications were implemented to meet testing criteria. 2.10 General Test Conditions/Configurations 2.10.1 Test Modes NOTE: The test mode(s) are selected according to relevant radio technology specifications. Test Mode Test Modes Description UMTS/TM1 WCDMA system, QPSK modulation UMTS/TM2 HSDPA system, QPSK modulation UMTS/TM3 HSUPA system, QPSK modulation Note: 1. This EUT owns two SIM cards, after we perform the pretest for these two SIM cards; we found the SIM 1 is the worst case, so its result is recorded in this report. 2. As WCDMA, HSDPA and HSUPA with the same emission designator, test result recorded in this report at the worst case UMTS/TM1 only after exploratory scan. 2.10.2 Test Environment Environment Parameter Selected Values During Tests Relative Humidity Ambient Temperature TN Ambient VL 3.4V Voltage VN 3.7V VH 4.2V NOTE: VL=lower extreme test voltage VN=nominal voltage VH=upper extreme test voltage TN=normal temperature This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E 3 TEST ENVIRONMENT 3.1 Address of the test laboratory Shenzhen LCS Compliance Testing Laboratory Ltd 1/F., Xingyuan Industrial Park, Tongda Road, Bao'an Avenue, Bao'an District, Shenzhen, Guangdong, China The sites are constructed in conformance with the requirements of ANSI C63.4 (2014) and CISPR Publication 22. 3.2 Test Facility The test facility is recognized, certified, or accredited by the following organizations: CNAS Registration Number. is L4595. FCC Registration Number. is 899208. Industry Canada Registration Number. is 9642A-1. VCCI Registration Number. is C-4260 and R-3804. ESMD Registration Number. is ARCB0108. UL Registration Number. is 100571-492. TUV SUD Registration Number. is SCN1081. TUV RH Registration Number. is UA 50296516-001 3.3 Environmental conditions During the measurement the environmental conditions were within the listed ranges: Temperature: 15-35 ° C Humidity: 30-60 % Atmospheric pressure: 950-1050mbar (1)expressed at approximately the 95% confidence level using a coverage factor of k=1.96. 3.4 Test Description 3.4.1 Cellular Band (824-849MHz paired with 869-894MHz) Test Item FCC Rule Requirements Verdict No. Effective(Isotropic) §2.1046, FCC: ERP ≤ 7W. Pass Radiated Output Power §22.913 Modulation §2.1047 Digital modulation N/A Characteristics OBW: No limit. Bandwidth §2.1049 Pass EBW: No limit. ≤-13dBm/1%*EBW, in 1MHz bands immediately outside Band Edges §2.1051, and adjacent to Pass Compliance §22.917 The frequency block. FCC: ≤ -13dBm/100kHz, Spurious Emission at §2.1051, from 9kHz to 10th harmonics but outside authorized Pass Antenna Terminals §22.917 operating frequency ranges. Field Strength of §2.1053, Spurious FCC: ≤ -13dBm/100kHz. Pass §22.917 Radiation §2.1055, Frequency Stability ≤ ±2.5ppm. Pass §22.355 NOTE 1: For the verdict, the “N/A” denotes “not applicable”, the “N/T” de notes “not tested”. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E 3.4.2 PCS Band (1850-1915MHz paired with 1930-1995MHz) Test Item FCC Rule Requirements Verdict No. Effective(Isotropic) §2.1046, EIRP ≤ 2W Pass Radiated Output Power §24.232 §2.1046, Peak-Average Ratio FCC:Limit≤13dB Pass §24.232 Modulation §2.1047 Digital modulation N/A Characteristics OBW: No limit. Bandwidth §2.1049 Pass EBW: No limit. ≤ -13dBm/1%*EBW, Band Edges §2.1051, In 1MHz bands immediately outside and adjacent to Pass Compliance §24.238 The frequency block. ≤-13dBm/1MHz, Spurious Emission at §2.1051, from 9kHz to10th harmonics but outside authorized Pass Antenna Terminals §24.238 Operating frequency ranges. Field Strength of §2.1053, Spurious ≤ -13dBm/1MHz. Pass §24.238 Radiation §2.1055, FCC: within authorized frequency Frequency Stability Pass §24.235 block. NOTE 1: For the verdict, the “N/A” denotes “not applicable”, the “N/T” de notes “not tested”. Remark: 1.The measurement uncertainty is not included in the test result. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E 3.5 Equipments Used during the Test Instrument Manufacturer Model No. Serial No. Characteristics Cal Date Due Date 9kHz – EMC Receiver R&S ESCS 30 100174 June 18,2015 June 17,2016 2.75GHz E4448A(External Signal analyzer Agilent US44300469 9kHz~40GHz July 16,2015 July 15,2016 mixers to 40GHz) LISN MESS Tec NNB-2/16Z 99079 9KHz-30MHz June 18,2015 June 17,2016 LISN EMCO 3819/2NM 9703-1839 9KHz-30MHz June 18,2015 June 17,2016 (Support Unit) RF Cable-CON UTIFLEX 3102-26886-4 CB049 9KHz-30MHz June 18,2015 June 17,2016 ISN SCHAFFNER ISN ST08 21653 9KHz-30MHz June 18,2015 June 17,2016 3m Semi Anechoic 30M-1GHz SIDT FRANKONIA SAC-3M 03CH03-HY June 18,2015 June 17,2016 Chamber 3m Amplifier SCHAFFNER COA9231A 18667 9kHz-2GHzz June 18,2015 June 17,2016 Amplifier Agilent 8449B 3008A02120 1GHz-26.5GHz July 16,2015 July 15,2016 26.5GHz- Amplifier MITEQ AMF-6F-260400 9121372 July 16,2015 July 15,2016 40GHz Spectrum Analyzer Agilent E4407B MY41440292 9k-26.5GHz July 16,2015 July 15,2016 MAX Signal Agilent N9020A MY50510140 20Hz~26.5GHz Oct. 27, 2015 Oct. 26, 2016 Analyzer Loop Antenna R&S HFH2-Z2 860004/001 9k-30MHz June 18,2015 June 17,2016 By-log Antenna SCHWARZBECK VULB9163 9163-470 30MHz-1GHz June 10,2015 June 09,2016 Horn Antenna EMCO 3115 6741 1GHz-18GHz June 10,2015 June 09,2016 Horn Antenna SCHWARZBECK BBHA9170 BBHA9170154 15GHz-40GHz June 10,2015 June 09,2016 RF Cable-R03m Jye Bao RG142 CB021 30MHz-1GHz June 18,2015 June 17,2016 RF Cable-HIGH SUHNER SUCOFLEX 106 03CH03-HY 1GHz-40GHz June 18,2015 June 17,2016 Spectrum Meter R&S FSP 30 100023 9kHz-30GHz July 16,2015 July 15,2016 Power Meter R&S NRVS 100444 DC-40GHz June 18,2015 June 17,2016 Power Sensor R&S NRV-Z51 100458 DC-30GHz June 18,2015 June 17,2016 Power Sensor R&S NRV-Z32 10057 30MHz-6GHz June 18,2015 June 17,2016 RF CABLE-1m JYE Bao RG142 CB034-1m 20MHz-7GHz June 18,2015 June 17,2016 RF CABLE-2m JYE Bao RG142 CB035-2m 20MHz-1GHz June 18,2015 June 17,2016 Vector signal R&S SMU200A 102098 100kHz~6GHz June 18,2015 June 17,2016 Generator Signal Generator R&S SMR40 10016 10MHz~40GHz July 16,2015 July 15,2016 Universal Radio Communication R&S CMU200 112012 N/A July 18,2015 July 17,2016 Tester DC power Source GW GPC-6030D C671845 / June 18,2015 June 17,2016 Temperature & Wuhuan HTP205 / / June 18,2015 June 17,2016 Humidity Chamber Note: All equipment through GRGT EST calibration This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E 3.6 Measurement uncertainty The data and results referenced in this document are true and accurate. The reader is cautioned that there may be errors within the calibration limits of the equipment and facilities. The measurement uncertainty was calculated for all measurements listed in this test report acc. to ETSI TR 100 028 “ Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics” and is documented in the Shenzhen LCS Compliance Testing Laboratory Ltd. quality system acc. to DIN EN ISO/IEC 17025. Furthermore, component and process variability of devices similar to that tested may result in additional deviation. The manufacturer has the sole responsibility of continued compliance of the device. Hereafter the best measurement capability for Shenzhen LCS Compliance Testing Laboratory Ltd. is reported: Measurement Test Range Notes Uncertainty Radiated Emission 30~1000MHz 3.10 dB (1) Radiated Emission 1~18GHz 3.70 dB (1) Radiated Emission 18-40GHz 3.90 dB (1) Conducted Disturbance 0.15~30MHz 1.63 dB (1) Conducted Power 9KHz~18GHz 0.61 dB (1) Spurious RF Conducted Emission 9KHz~40GHz 1.22 dB (1) Band Edge Compliance of RF Emission 9KHz~40GHz 1.22 dB (1) Occuiped Bandwidth 9KHz~40GHz - (1) (1) This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=1.96. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E 4 TEST CONDITIONS AND RESULTS 4.1 Output Power TEST APPLICABLE During the process of testing, the EUT was controlled via R&S Digital Radio Communication tester (CMU200) to ensure max power transmission and proper modulation. This result contains output power and EIRP measurements for the EUT. In all cases, output power is within the specified limits. 4.1.1. Conducted Output Power TEST CONFIGURATION TEST PROCEDURE Conducted Power Measurement: a) Place the EUT on a bench and set it in transmitting mode. b) Connect a low loss RF cable from the antenna port to a CMU200 by an Att. c) EUT Communicate with CMU200 then selects a channel for testing. d) Add a correction factor to the display CMU200, and then test. TEST RESULTS See next page This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E Burst Average Conducted power (dBm) Test Mode Test Channel UMTS Band V UMTS Band II LCH 23.67 23.56 UMTS/TM1 MCH 23.66 23.55 HCH 23.63 23.52 LCH_SubTest-1 23.41 23.47 LCH_SubTest-2 22.74 22.26 LCH_SubTest-3 21.58 21.45 LCH_SubTest-4 21.36 21.63 MCH_SubTest-1 23.41 23.15 MCH_SubTest-2 22.56 22.47 UMTS/TM2 MCH_SubTest-3 22.50 22.23 MCH_SubTest-4 21.57 21.52 HCH_SubTest-1 23.26 23.03 HCH_SubTest-2 22.20 22.41 HCH_SubTest-3 22.15 21.78 HCH_SubTest-4 21.44 21.56 LCH_SubTest-1 22.47 22.77 LCH_SubTest-2 21.36 21.25 LCH_SubTest-3 22.25 22.46 LCH_SubTest-4 20.46 20.17 LCH_SubTest-5 21.74 21.63 MCH_SubTest-1 22.36 22.67 MCH_SubTest-2 21.22 21.22 UMTS/TM3 MCH_SubTest-3 22.36 22.56 MCH_SubTest-4 21.44 21.23 MCH_SubTest-5 21.85 21.41 HCH_SubTest-1 22.45 22.78 HCH_SubTest-2 21.36 21.55 HCH_SubTest-3 22.42 22.23 HCH_SubTest-4 20.25 21.16 HCH_SubTest-5 21.57 21.45 This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E 4.1.1 Radiated Output Power TEST DESCRIPTION This is the test for the maximum radiated power from the EUT. Rule Part 24.232(c) specifies, "Mobile/portable stations are limited to 2 watts e.i.r.p. Peak power" and 24.232(e) specifies that "Peak transmit power must be measured over any interval of continuous transmission using instrumentation calibrated in terms of an rms-equivalent voltage." Rule Part 22.913(a) specifies ” The ERP of mobile transmitters and auxiliary test transmitters must not exceed 7 Watts.” Per Part 27.50(d) (4) specifies, Fixed, mobile, and portable (hand-held) stations operating in the 1710- 1755MHz band are limited to 1W EIRP. Fixed stations operating in this band are limited to a maximum antenna height of 10 meters above ground. Mobile and portable stations operating in this band must employ a means for limiting power to the minimum necessary for successful communications. TEST CONFIGURATION TEST PROCEDURE 1. EUT was placed on a 1.50 meter high non-conductive stand at a 3 meter test distance from the receive antenna. A receiving antenna was placed on the antenna mast 3 meters from the EUT for emission measurements. The height of receiving antenna is 1.50m. Detected emissions were maximized at each frequency by rotating the EUT through 360° and adjusting the receiving antenna polarization. The radiated emission measurements of all transmit frequencies in three channels (High, Middle, Low) were measured with peak detector. 2. A log-periodic antenna or double-ridged waveguide horn antenna shall be substituted in place of the EUT. The log-periodic antenna will be driven by a signal generator and the level will be adjusted till the same power value on the spectrum analyzer or receiver. The level of the spurious emissions can be calculated through the level of the signal generator, cable loss, the gain of the substitution antenna and the reading of the spectrum analyzer or receiver. 3. The EUT is then put into continuously transmitting mode at its maximum power level during the test.Set Test Receiver or Spectrum RBW=10MHz,VBW=10MHz, And the maximum value of the receiver should be recorded as (Pr). 4. The EUT shall be replaced by a substitution antenna. In the chamber, an substitution antenna for the frequency band of interest is placed at the reference point of the chamber. An RF Signal source for the frequency band of interest is connected to the substitution antenna with a cable that has been constructed to not interfere with the radiation pattern of the antenna. A power (PMea) is applied to the input of the substitution antenna, and adjust the level of the signal generator output until the value of the receiver This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E reach the previously recorded (Pr). The power of signal source (PMea) is recorded. The test should be performed by rotating the test item and adjusting the receiving antenna polarization. 5. A amplifier should be connected to the Signal Source output port. And the cable should be connect between the Amplifier and the Substitution Antenna. The cable loss (Pcl) ,the Substitution Antenna Gain (Ga) and the Amplifier Gain (PAg) should be recorded after test. The measurement results are obtained as described below: Power(EIRP)=PMea- PAg - Pcl + Ga 6. This value is EIRP since the measurement is calibrated using an antenna of known gain (2.15 dBi) and known input power. 7. ERP can be calculated from EIRP by subtracting the gain of the dipole, ERP = EIRP-2.15dBi. TEST LIMIT According to 22.913(a), 24.232(c) and 27.50(d) (4), the ERP(EIRP) should be not exceeding following table limits: Burst Average EIRP UMTS Band II 33dBm (2W) Burst Average ERP UMTS Band V 38.45dBm (7W) TEST RESULTS Remark: 1. We were tested all Configuration refer 3GPP TS134 121. 2. EIRP=PMea(dBm)-Pcl(dB)+PAg(dB)+Ga(dBi) 3. ERP = EIRP – 2.15dBi as EIRP by subtracting the gain of the dipole. 4. Margin = Emission Level - Limit 5. We test the H direction and V direction recorded worst case. UMTS/TM1/UMTS Band II Ga Peak Frequency PMea Pcl PAg Limit Margin Antenna EIRP Polarization (MHz) (dBm) (dB) (dB) (dBm) (dB) Gain(dB) (dBm) 1852.4 -16.41 4.03 8.38 35.51 23.45 33.01 -9.56 V 1880.0 -16.70 4.08 8.33 35.56 23.11 33.01 -9.90 V 1907.6 -17.61 4.14 8.26 35.63 22.14 33.01 -10.87 V UMTS/TM1/UMTS Band V Ga Peak Frequency PMea Pcl Correction PAg Limit Margin Antenna ERP Polarization (MHz) (dBm) (dB) (dB) (dB) (dBm) (dB) Gain(dB) (dBm) 826.40 -15.07 3.45 8.45 2.15 33.79 21.57 38.45 -16.88 V 836.60 -15.65 3.49 8.45 2.15 33.85 21.01 38.45 -17.44 V 846.60 -16.11 3.55 8.36 2.15 33.88 20.43 38.45 -18.02 V This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E 4.2 Radiated Spurious Emssion TEST APPLICABLE According to the TIA/EIA 603D:2010 test method, The Receiver or Spectrum was scanned from 9 KHz to the 10th harmonic of the highest frequency generated within the equipment, which is the transmitted carrier that can be as high as 1910 MHz The resolution bandwidth is set as outlined in Part 24.238, Part 22.917 and Part 27.54. The spectrum is scanned with the mobile station transmitting at carrier frequencies that pertain to low, mid and high channels of WCDMA Band II WCDMA Band IV and WCDMA Band V. TEST CONFIGURATION TEST PROCEDURE 1. EUT was placed on a 1.50 meter high non-conductive stand at a 3 meter test distance from the receive antenna. A receiving antenna was placed on the antenna mast 3 meters from the EUT for emission measurements. The height of receiving antenna is 1.50 m. Detected emissions were maximized at each frequency by rotating the EUT through 360° and adjusting the receiving antenna polarization. The radiated emission measurements of all transmit frequencies in three channels (High, Middle, Low) were measured with peak detector. 2. A log-periodic antenna or double-ridged waveguide horn antenna shall be substituted in place of the EUT. The log-periodic antenna will be driven by a signal generator and the level will be adjusted till the same power value on the spectrum analyzer or receiver. The level of the spurious emissions can be calculated through the level of the signal generator, cable loss, the gain of the substitution antenna and the reading of the spectrum analyzer or receiver. 3. The EUT is then put into continuously transmitting mode at its maximum power level during the test.Set Test Receiver or Spectrum RBW=1MHz,VBW=3MHz, And the maximum value of the receiver should be recorded as (Pr). 4. The EUT shall be replaced by a substitution antenna. In the chamber, an substitution antenna for the frequency band of interest is placed at the reference point of the chamber. An RF Signal source for the frequency band of interest is connected to the substitution antenna with a cable that has been constructed to not interfere with the radiation pattern of the antenna. A power (PMea) is applied to the input of the substitution antenna, and adjust the level of the signal generator output until the value of the receiver reach the previously recorded (Pr). The power of signal source (PMea) is recorded. The test should be performed by rotating the test item and adjusting the receiving antenna polarization. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E 5. A amplifier should be connected to the Signal Source output port. And the cable should be connect between the Amplifier and the Substitution Antenna. The cable loss (Pcl) ,the Substitution Antenna Gain (Ga) and the Amplifier Gain (PAg) should be recorded after test. The measurement results are obtained as described below: Power(EIRP)=PMea- PAg - Pcl + Ga 6. This value is EIRP since the measurement is calibrated using an antenna of known gain (2.15 dBi) and known input power. 7. ERP can be calculated from EIRP by subtracting the gain of the dipole, ERP = EIRP -2.15dBi. 8. In order to make sure test results more clearly,we set frequency range and sweep time for difference frequency range as follows table: Working Subrange Sweep time RBW VBW Frequency (GHz) (s) 0.00009~0.15 1KHz 3KHz 30 0.00015~0.03 10KHz 30KHz 10 0.03~1 100KHz 300KHz 10 UMTS/TM1/ 1~2 1 MHz 3 MHz 2 WCDMA Band V 2~5 1 MHz 3 MHz 3 5~8 1 MHz 3 MHz 3 8~10 1 MHz 3 MHz 3 0.00009~0.15 1KHz 3KHz 30 0.00015~0.03 10KHz 30KHz 10 0.03~1 100KHz 300KHz 10 1~2 1 MHz 3 MHz 2 UMTS/TM1/ 2~5 1 MHz 3 MHz 3 WCDMA Band II 5~8 1 MHz 3 MHz 3 8~11 1 MHz 3 MHz 3 11~14 1 MHz 3 MHz 3 14~18 1 MHz 3 MHz 3 18~20 1 MHz 3 MHz 2 TEST LIMITS According to 24.238, 22.917 and 27.54 specify that the power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 + 10 log(P) dB. The specification that emissions shall be attenuated below the transmitter power (P) by at least 43 + 10 log (P) dB, translates in the relevant power range (1 to 0.001 W) to -13 dBm. At 1 W the specified minimum attenuation becomes 43 dB and relative to a 30 dBm (1 W) carrier becomes a limit of -13 dBm. At 0.001 W (0 dBm) the minimum attenuation is 13 dB, which again yields a limit of -13 dBm. In this way a translation of the specification from relative to absolute terms is carried out. Frequency Channel Frequency Range Verdict Low 9KHz-10GHz PASS UMTS/TM1/ WCDMA Middle 9KHz -10GHz PASS Band V High 9KHz -10GHz PASS Low 9KHz -20GHz PASS UMTS/TM1/ WCDMA Middle 9KHz -20GHz PASS Band II High 9KHz -20GHz PASS This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E TEST RESULTS Remark: 1. We were tested all Configuration refer 3GPP TS134 121. 2. EIRP=PMea(dBm)-Pcl(dB)+PAg(dB)+Ga(dBi) 3. ERP = EIRP – 2.15dBi as EIRP by subtracting the gain of the dipole. 4. Margin = EIRP - Limit UMTS/TM1/ WCDMA Band II _ Low Channel Ga Peak Frequency PMea Pcl Limit Margin Diatance Antenna EIRP Polarization (MHz) (dBm) (dB) (dBm) (dB) Gain(dB) (dBm) 3704.8 -39.85 5.26 3.00 9.88 -35.23 -13.00 -22.23 H 5557.2 -44.87 6.11 3.00 11.36 -39.62 -13.00 -26.62 H 3704.8 -43.17 5.26 3.00 9.88 -38.55 -13.00 -25.55 V 5557.2 -47.70 6.11 3.00 11.36 -42.45 -13.00 -29.45 V UMTS/TM1/ WCDMA Band II _ Middle Channel Ga Peak Frequency PMea Pcl Limit Margin Diatance Antenna EIRP Polarization (MHz) (dBm) (dB) (dBm) (dB) Gain(dB) (dBm) 3760.0 -38.82 5.32 3.00 10.03 -34.11 -13.00 -21.11 H 5640.0 -45.11 6.19 3.00 11.41 -39.89 -13.00 -26.89 H 3760.0 -43.28 5.32 3.00 10.03 -38.57 -13.00 -25.57 V 5640.0 -47.63 6.19 3.00 11.41 -42.41 -13.00 -29.41 V UMTS/TM1/ WCDMA Band II _ High Channel Ga Peak Frequency PMea Pcl Limit Margin Diatance Antenna EIRP Polarization (MHz) (dBm) (dB) (dBm) (dB) Gain(dB) (dBm) 3815.2 -40.41 5.36 3.00 9.62 -36.15 -13.00 -23.15 H 5722.8 -46.00 6.24 3.00 11.46 -40.78 -13.00 -27.78 H 3815.2 -43.51 5.36 3.00 9.62 -39.25 -13.00 -26.25 V 5722.8 -49.58 6.24 3.00 11.46 -44.36 -13.00 -31.36 V UMTS/TM1/ WCDMA Band V _ Low Channel Ga Peak Frequency PMea Pcl Limit Margin Diatance Antenna EIRP Polarization (MHz) (dBm) (dB) (dBm) (dB) Gain(dB) (dBm) 1652.8 -43.73 3.86 3.00 8.56 -39.03 -13.00 -26.03 H 2479.2 -46.83 4.29 3.00 6.98 -44.14 -13.00 -31.14 H 1652.8 -46.97 3.86 3.00 8.56 -42.27 -13.00 -29.27 V 2479.2 -49.34 4.29 3.00 6.98 -46.65 -13.00 -33.65 V UMTS/TM1/ WCDMA Band V _ Middle Channel Ga Peak Frequency PMea Pcl Limit Margin Diatance Antenna EIRP Polarization (MHz) (dBm) (dB) (dBm) (dB) Gain(dB) (dBm) 1672.8 -44.46 3.90 3.00 8.58 -39.78 -13.00 -26.78 H 2509.2 -47.61 4.32 3.00 6.80 -45.13 -13.00 -32.13 H 1672.8 -45.79 3.90 3.00 8.58 -41.11 -13.00 -28.11 V 2509.2 -49.93 4.32 3.00 6.80 -47.45 -13.00 -34.45 V UMTS/TM1/ WCDMA Band V _ High Channel Ga Peak Frequency PMea Pcl Limit Margin Diatance Antenna EIRP Polarization (MHz) (dBm) (dB) (dBm) (dB) Gain(dB) (dBm) 1693.2 -45.13 3.91 3.00 9.06 -39.98 -13.00 -26.98 H 2539.8 -47.96 4.32 3.00 6.65 -45.63 -13.00 -32.63 H 1693.2 -46.56 3.91 3.00 9.06 -41.41 -13.00 -28.41 V 2539.8 -49.88 4.32 3.00 6.65 -47.55 -13.00 -34.55 V This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E 4.3 Occupied Bandwidth and Emission Bandwith TEST APPLICABLE Similar to conducted emissions; occupied bandwidth measurements are only provided for selected frequencies in order to reduce the amount of submitted data. The table below lists the measured 99% Bandwidth and -26dBc Bandwidth. TEST CONFIGURATION TEST PROCEDURE 1. The EUT was set up for the max output power with pseudo random data modulation; 2. The Occupied bandwidth and Emission Bandwidth were measured with Aglient Spectrum Analyzer N9020A (peak); 3. Set RBW=100KHz,VBW=300KHz,Span=10MHz,SWT=Auto; 4. Set SPA Max hold and View, Set 99% Occupied Bandwidth/ Set -26dBc Occupied Bandwidth 5. These measurements were done at 3 frequencies for WCDMA band II/IV/V. (low, middle and high of operational frequency range). TEST RESULTS Occupied Bandwidth Emission Bandwidth Frequency Test Mode Channel (99% BW) (-26 dBc BW) Verdict (MHz) ( MHz) ( MHz) UMTS/TM1/ 4132 826.40 4.1493 4.701 PASS WCDMA Band 4183 836.60 4.1854 4.745 PASS V 4233 846.60 4.1547 4.714 PASS UMTS/TM1/ 9262 1852.40 4.1716 4.698 PASS WCDMA Band 9400 1880.00 4.1427 4.666 PASS II 9538 1907.60 4.1799 4.749 PASS Remark: 1. Test results including cable loss; 2. please refer to following plots; This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E Occupied Bandwidth and Emission Bandwidth UMTS/TM1/ WCDMA Band V UMTS/TM1/ WCDMA Band II Channel 4132 / 826.4 MHz Channel 9262 / 1852.4 MHz Channel 4183 / 836.6 MHz Channel 9400 / 1880.0 MHz Channel 4233 / 846.6 MHz Channel 9538 / 1907.6 MHz This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E 4.4 Band Edge Compliance TEST APPLICABLE During the process of testing, the EUT was controlled via Digital Radio Communication tester (CMU200) to ensure max power transmission and proper modulation. TEST CONFIGURATION TEST PROCEDURE 1. The EUT was set up for the max output power with pseudo random data modulation; 2. The power was measured with Spectrum Analyzer N9020A; 3. Set RBW=100KHz,VBW=300KHz,Span=10MHz,SWT=Auto,Dector: RMS; These measurements were done at 2 frequencies for WCDMA Band II/V/IV. (low and high of operational frequency range). TEST RESULTS UMTS/TM1/WCDMA Band V Frequency Band Edg Compliance Limits Test Mode Channel Verdict (MHz) (dBm) (dBm) UMTS/TM1/WCDMA 4132 826.40 <-13dBm -13dBm PASS Band V 4233 846.60 <-13dBm -13dBm UMTS/TM1/WCDMA Band II Frequency Band Edg Compliance Limits Test Mode Channel Verdict (MHz) (dBm) (dBm) UMTS/TM1/WCDMA 9262 1852.40 <-13dBm -13dBm PASS Band II 9538 1907.60 <-13dBm -13dBm Remark: 1. Test results including cable loss; 2. please refer to following plots; This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E Band-edge Compliance UMTS/TM1/WCDMA Band V UMTS/TM1/WCDMA Band II Channel 4132 / 826.4 MHz Channel 9262 / 1852.4 MHz Channel 4233 / 846.6 MHz Channel 9538 / 1907.6 MHz This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E 4.5 Spurious Emssion on Antenna Port TEST APPLICABLE The following steps outline the procedure used to measure the conducted emissions from the EUT. 1. Determine frequency range for measurements: From CFR 2.1057 the spectrum should be investigated from the lowest radio frequency generated in the equipment up to at least the 10th harmonic of the carrier frequency. For the equipment of WCDMA band II, this equates to a frequency range of 9 KHz to 20GHz, data taken from 30 MHz to 20 GHz.For WCDMA Band V, data taken from 30 MHz to 10 GHz. 2. The sweep time is set automatically by instrument itself. That should be the optimal sweep time for the span and the RBW. If the sweep time is too short, that is sweep is too fast, the sweep result is not accurate; if the sweep time is too long, that is sweep is too low, some frequency components may be lost. The instrument will give an optimal sweep time according the selected span and RBW. 3. The procedure to get the conducted spurious emission is as follows: The trace mode is set to MaxHold to get the highest signal at each frequency; Wait 25 seconds; Get the result. 4. Determine EUT transmit frequencies: below outlines the band edge frequencies pertinent to conducted emissions testing. TEST CONFIGURATION TEST PROCEDURE 1. The EUT was set up for the max output power with pseudo random data modulation; 2. The power was measured with Spectrum Analyzer N9020A; 3. These measurements were done at 3 frequencies for WCDMA band II/V. (low, middle and high of operational frequency range). TEST LIMIT Part 24.238, Part 22.917 and Part 27.54 specify that the power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 + 10 log(P) dB. The specification that emissions shall be attenuated below the transmitter power (P) by at least 43 + 10 log (P) dB, translates in the relevant power range (1 to 0.001 W) to -13 dBm. At 1 W the specified minimum attenuation becomes 43 dB and relative to a 30 dBm (1 W) carrier becomes a limit of -13 dBm. At 0.001 W (0 dBm) the minimum attenuation is 13 dB, which again yields a limit of -13 dBm. In this way a translation of the specification from relative to absolute terms is carried out. TEST RESULTS This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E Spurious RF Frequency Limits Test Mode Channel Conducted Emission Verdict (MHz) (dBm) (dBm) 4132 826.40 <-13dBm -13dBm UMTS/TM1/WCDMA 4183 836.60 <-13dBm -13dBm PASS Band V 4233 846.60 <-13dBm -13dBm 9262 1852.40 <-13dBm -13dBm UMTS/TM1/WCDMA 9400 1880.00 <-13dBm -13dBm PASS Band II 9538 1907.60 <-13dBm -13dBm Remark: 1. Test results including cable loss; 2. please refer to following plots; This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E Spurious Emssion on Antenna Port UMTS/TM1/WCDMA Band V Channel 4132 / 826.4 MHz Channel 4183 / 836.6 MHz 30 MHz – 1000 MHz 30 MHz – 1000 MHz 1 GHz – 9 GHz 1 GHz – 9 GHz UMTS/TM1/WCDMA Band V Channel 4233 / 846.6 MHz Channel 4233 / 846.6 MHz 30 MHz – 1000 MHz 1 GHz – 9 GHz This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E Spurious Emssion on Antenna Port UMTS/TM1/WCDMA Band II Channel 9262 / 1852.4 MHz Channel 9400 / 1880.0 MHz 30 MHz – 1000 MHz 30 MHz – 1000 MHz 1 GHz – 20 GHz 1 GHz – 20 GHz UMTS/TM1/WCDMA Band II Channel 9538 / 1907.6 MHz Channel 9538 / 1907.6 MHz 30 MHz – 1000 MHz 1 GHz – 20 GHz This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E 4.6 Frequency Stability Test TEST APPLICABLE 1. According to FCC Part 2 Section 2.1055 (a)(1), the frequency stability shall be measured with variation of ambient temperature from -30℃ to +50℃ centigrade. 2. According to FCC Part 2 Section 2.1055 (E) (2), for battery powered equipment, the frequency stability shall be measured with reducing primary supply voltage to the battery operating end point, which is specified by the manufacture. 3. Vary primary supply voltage from 85 to 115 percent of the nominal value for other than hand carried voltage equipment and the end voltage point was 3.40V. TEST PROCEDURE In order to measure the carrier frequency under the condition of AFC lock, it is necessary to make measurements with the EUT in a “call mode”. This is accomplished with the use of R&S CMU200 DIGITAL RADIO COMMUNICATION TESTER. 1. Measure the carrier frequency at room temperature; 2. Subject the EUT to overnight soak at -30℃; 3. With the EUT, powered via nominal voltage, connected to the CMU200 and in a simulated call on middle channel of WCDMA Band II/V, measure the carrier frequency. These measurements should be made within 2 minutes of Powering up the EUT, to prevent significant self-warming; 4. Repeat the above measurements at 10℃ increments from -30℃ to +50℃. Allow at least 0.5 hours at each temperature, unpowered, before making measurements; 5. Remeasure carrier frequency at room temperature with nominal voltage. Vary supply voltage from minimum voltage to maximum voltage, in 0.1Volt increments remeasuring carrier frequency at each voltage. Pause at nominal voltage for 0.5 hours unpowered, to allow any self-heating to stabilize, before continuing; 6. Subject the EUT to overnight soak at +50℃; 7. With the EUT, powered via nominal voltage, connected to the CMU200 and in a simulated call on the centre channel, measure the carrier frequency. These measurements should be made within 2 minutes of Powering up the EUT, to prevent significant self-warming; 8. Repeat the above measurements at 10℃ increments from +50℃ to -30℃. Allow at least 0.5 hours at each temperature, unpowered, before making measurements; 9. At all temperature levels hold the temperature to +/- 0.5℃ during the measurement procedure; TEST CONFIGURATION This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E TEST LIMITS For Hand carried battery powered equipment According to the JTC standard the frequency stability of the carrier shall be accurate to within 0.1 ppm of the received frequency from the base station. This accuracy is sufficient to meet Sec. 24.235, Frequency Stability. The frequency stability shall be sufficient to ensure that the fundamental emission stays within the authorized frequency block. As this transceiver is considered "Hand carried, battery powered equipment" Section 2.1055(d)(2) applies. This requires that the lower voltage for frequency stability testing be specified by the manufacturer. This transceiver is specified to operate with an input voltage of between 3.30VDC and 4.20VDC, with a nominal voltage of 3.70DC. Operation above or below these voltage limits is prohibited by transceiver software in order to prevent improper operation as well as to protect components from overstress. These voltages represent a tolerance of -10 % and +12.5 %. For the purposes of measuring frequency stability these voltage limits are to be used. For equipment powered by primary supply voltage According to the JTC standard the frequency stability of the carrier shall be accurate to within 0.1 ppm of the received frequency from the base station. This accuracy is sufficient to meet Sec. 24.235, Frequency Stability. The frequency stability shall be sufficient to ensure that the fundamental emission stays within the authorized frequency block. For this EUT section 2.1055(d)(1) applies. This requires varying primary supply voltage from 85 to 115 percent of the nominal value for other than hand carried battery equipment. TEST RESULTS UMTS/TM1/WCDMA Band II Temperature Frequency Frequency Limit DC Power Verdict (℃) error(Hz) error(ppm) (ppm) 3.40 20 13 0.007 2.50 PASS 3.70 20 15 0.008 2.50 PASS 4.20 20 19 0.010 2.50 PASS 3.70 -30 11 0.006 2.50 PASS 3.70 -20 13 0.007 2.50 PASS 3.70 -10 18 0.010 2.50 PASS 3.70 0 12 0.006 2.50 PASS 3.70 10 15 0.008 2.50 PASS 3.70 20 11 0.006 2.50 PASS 3.70 30 17 0.009 2.50 PASS 3.70 40 11 0.006 2.50 PASS 3.70 50 16 0.008 2.50 PASS UMTS/TM1/WCDMA Band V Temperature Frequency Frequency Limit DC Power Verdict (℃) error(Hz) error(ppm) (ppm) 3.40 20 12 0.014 2.50 PASS 3.70 20 20 0.024 2.50 PASS 4.20 20 18 0.022 2.50 PASS 3.70 -30 16 0.019 2.50 PASS 3.70 -20 11 0.013 2.50 PASS 3.70 -10 13 0.016 2.50 PASS 3.70 0 11 0.013 2.50 PASS 3.70 10 12 0.014 2.50 PASS 3.70 20 14 0.017 2.50 PASS 3.70 30 15 0.018 2.50 PASS 3.70 40 11 0.013 2.50 PASS 3.70 50 16 0.019 2.50 PASS This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E 4.7 Peak-to-Average Ratio (PAR) LIMIT The Peak-to-Average Ratio (PAR) of the transmission may not exceed 13 dB. TEST CONFIGURATION TEST PROCEDURE 1. Refer to instrument’s analyzer instruction manual for details on how to use the power statistics/CCDF function; 2. Set resolution/measurement bandwidth ≥ signal’s occupied bandwidth; 3. Set the number of counts to a value that stabilizes the measured CCDF curve; 4. Set the measurement interval as follows: 1). for continuous transmissions, set to 1 ms, 2). for burst transmissions, employ an external trigger that is synchronized with the EUT burst timing sequence, or use the internal burst trigger with a trigger level that allows the burst to stabilize and set the measurement interval to a time that is less than or equal to the burst duration. 5. Record the maximum PAPR level associated with a probability of 0.1%. TEST RESULTS Frequency PAPR Value Limits Test Mode Channel Verdict (MHz) (dB) (dB) UMTS/TM1/ 9262 1852.40 2.79 13.0 PASS WCDMA Band 9400 1880.00 2.99 13.0 PASS II 9538 1907.60 2.40 13.0 PASS Remark: 1. Test results including cable loss; 2. please refer to following plots; This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E Peak-to-Average Ratio (PAR) UMTS/TM1/ WCDMA Band II Channel 9262 / 1852.4 MHz Channel 9400 / 1880.0 MHz Channel 9538 / 1907.6 MHz This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: VUJ-AT312 Report No.: LCS1607050245E 5 Test Setup Photos of the EUT Please refer to separated files for Test Setup Photos of the EUT. 6 External Photos of the EUT Please refer to separated files for External Photos of the EUT. 7 Internal Photos of the EUT Please refer to separated files for Internal Photos of the EUT. .........................End of Report......................... This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.


Document Created: 2016-07-18 20:18:11
Document Modified: 2016-07-18 20:18:11
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC