Cover Letter (Modular Approval Request).pdf

FCC ID: VPYLB1DX

Cover Letter(s)

Download: PDF
FCCID_2972930

RF_734_00, Issue 1 Modular Approval Request FCC (per DA 00—1407) FCC ID: VPYLBIDX Items to be covered Answerfrom applicant 1. The modular transmitter must have its own RF shielding. Yes 2. The modular transmitter must have buffered modulation/data inputs (if such inputs Yes are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over—modulation. 3. The modular transmitter must have its own power supply regulation. Yes 4. The modular transmitter must comply with the antenna requirements of Section Yes 15.203 and 15.204(c). The antenna must either be permanently attached or employ a "unique" antenna coupler (at all connections between the module and the antenna, including the cable).. The modular transmitter must be tested in a stand—alone configuration, i.e., the No module must not be inside another device during testing. This is intended to The modular transmitter has been demonstrate that the module is capable of complying with Part 15 emission limits performed the testing in a state of regardless of the device into which it is eventually installed. being installed on a test jig board simulating the board of the installed end product, therefore has not been performed the testing as a standalone and then confirmed the compliance. The module and antenna will be mounted on a board similar to the one shown in the test set photo, and the board will be installed in the end product. 6. The modular transmitter must be labeled with its own FCC ID number, and, if the No FCC ID is not visible when the module is installed inside another device, then the Since there is no space which outside of the device into which the module is installed must also display a label indicates FCC ID, FCC ID is not referring to the enclosed module. This exterior label can use wording such as the indicated on the label. So FCC ID is following: "Contains Transmitter Module FCC ID: XYZMODEL1" or "Contains indicated in the manual, then the FCC ID: XYZMODEL1." Any similar wording that expresses the same meaning outside of the device into which the may be used. The Grantee may either provide such a label, an example of which module is installed also displays a must be included in the application for equipment authorization, or, must provide label referring to the enclosed adequate instructions along with the module which explain this requirement. In the module. latter case, a copy of these instructions must be included in the application for equipment authorization. 7. The modular transmitter must comply with any specific rule or operating Yes requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. 8. The modular transmitter must comply with any applicable RF exposure Yes requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific Sections of Part 15, including 15.3 19(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance.

RF_734_00, Issue 1 Note: If compliance with one or more of the numbered requirements, listed above, cannot be demonstrated, it may be possible to obtain a "Limited Modular Approval" (LMA). Name and surname of applicant (or authorized representative): Takahiro Watanabe Date: 2016—02—26 Signature: jfi%fl/g yp Woterabre


Document Created: 2019-06-20 17:18:50
Document Modified: 2019-06-20 17:18:50
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC