FCC ID Label

FCC ID: VOB-M705

ID Label/Location Info

Download: PDF
FCCID_858161

 Nvidia Corporation                                                                                  Model: M705

16 EXHIBIT A – FCC & IC EQUIPMENT LABELING REQUIREMENTS
16.1 FCC § 2.925 Identification of equipment
(a) Each equipment covered in an application for equipment authorization shall bear a nameplate or label
listing the following:

(1) FCC Identifier consisting of the two elements in the exact order specified in §2.926. The FCC Identifier
shall be preceded by the term FCC ID in capital letters on a single line, and shall be of a type size large
enough to be legible without the aid of magnification.

Example: FCC ID XXX123. XXX—Grantee Code 123—Equipment Product Code

16.2 FCC ID Labeling Requirements as per FCC § 15.19

(a) In addition to the requirements in part 2 of this chapter, a device subject to certification, or verification
shall be labeled as follows:
(3) All other devices shall bear the following statement in a conspicuous location on the device:

        This device complies with part 15 of the FCC Rules. Operation is subject to the following two
        conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
        interference received, including interference that may cause undesired operation.

(4) Where a device is constructed in two or more sections connected by wires and marketed together, the
statement specified above is required to be affixed only to the main control unit. If the EUT is integrated
within another device then a label affixed to the host shall also state, “Contains FCC ID:XXXXXX”

(5) When the device is so small or for such use that it is not practicable to place the statement specified under
paragraph (a) of this section on it, the information required by this paragraph shall be placed in a prominent
location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the
container in which the device is marketed. However, the FCC identifier or the unique identifier, as
appropriate, must be displayed on the device.

IC: XXXXXX-YYYYYYYY Where:
    •     "XXXXXX-YYYYYYYY" is the certification number
    •     "XXXXXX" is the Certificate Holder Number (CHN), made of at most 6 alphanumeric characters (A-Z, 0-9),
          assigned by Industry Canada; and
    •     "YYYYYYYY" is the Unique Product Number (UPN), made of at most 8 alphanumeric characters (A-Z, 0-9)
          assigned by the applicant.
    •     Note 1: The term "IC" before the equipment certification number only signifies that the Industry Canada
          technical specifications were met.
    •     Note 2: Note 1 shall be conspicuously placed in the equipment user manual.
    •     Note 3: Permitted alphanumeric characters used in the CHN and UPN are limited to capital letters (A-Z) and
          digits (0-9). Other characters, such as "#", "/" or "-", shall not be used.




Report Number: R0707102                          Page 53 of 59                       FCC Part 15.247 and IC RSS-210


 Nvidia Corporation                                                                                                     Model: M705

16.3 Specifications: As per RSS GEN 5.2 Equipment Labeling:

Equipment subject to certification under the applicable RSS, shall be permanently labeled on each item, or as
an inseparable combination. The label must contain the following information for full compliance:
(a) the certification number, prefixed by the term “IC:”;
(b) the manufacturer's name, trade name or brand name; and
(c) a model name or number.
Equipment for which a certificate has been issued is not considered certified if it is not properly labeled.
The information on the Canadian label can be combined with the manufacturer’s other labeling requirements.
If the device size is too small to put a label, the label can be included in the user’s manual, upon agreement
with Industry Canada.


16.4 Suggested FCC ID & IC Label


   Model: M705
   This device complies with part 15 of the FCC Rules. Operation is subject to the following two
   conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
   interference received, including interference that may cause undesired operation.

   FCC ID: VOB-M705
   IC: 7361A-M705

   NVIDIA Corporation


16.5 Suggested Label Location (EUT interface side view)




Report Number: R0707102                                    Page 54 of 59                                 FCC Part 15.247 and IC RSS-210



Document Created: 2007-10-05 14:46:01
Document Modified: 2007-10-05 14:46:01

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC