Test Report BLE

FCC ID: VLJ-SMART63

Test Report

Download: PDF
FCCID_2494645

Shenzhen Zhongjian Nanfang Testing Co., Ltd. Report No: CCIS14100084802 1 Cover Page FCC & IC REPORT (BLE) Applicant: Binatone Electronics International Limited Address of Applicant: Floor 23A, 9 Des Voeux Road West, Sheung Wan, Hong Kong Equipment Under Test (EUT) Product Name: DECT Phone Model No.: Smart 63, KS7106 FCC ID: VLJ-SMART63 Canada IC: 4522A-SMART63 FCC CFR Title 47 Part 15 Subpart C Section 15.247 Applicable standards: RSS-210 Issue 8, December 2010 RSS-Gen Issue 4, November 2014 Date of sample receipt: 14 Oct., 2014 Date of Test: 14 Oct., 2014 to 06 Nov., 2014 Date of report issued: 06 Nov., 2014 Test Result: PASS * * In the configuration tested, the EUT complied with the standards specified above. Authorized Signature: Bruce Zhang Laboratory Manager This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product and does not permit the use of the CCIS product certification mark. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.

Report No: CCIS14100084802 2 Version Version No. Date Description 00 06 Nov., 2014 Original Tested by: Date: 06 Nov., 2014 Test Engineer Reviewed by: Date: 06 Nov., 2014 Project Engineer Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 2 of 37

Report No: CCIS14100084802 3 Contents Page 1 COVER PAGE ................................................................................................................................................... 1 2 VERSION ........................................................................................................................................................... 2 3 CONTENTS ....................................................................................................................................................... 3 4 TEST SUMMARY .............................................................................................................................................. 4 5 GENERAL INFORMATION .............................................................................................................................. 5 5.1 CLIENT INFORMATION ............................................................................................................................................ 5 5.2 GENERAL DESCRIPTION OF E.U.T........................................................................................................................ 5 5.3 TEST ENVIRONMENT AND MODE ............................................................................................................................ 7 5.4 DESCRIPTION OF SUPPORT UNITS ........................................................................................................................ 7 5.5 LABORATORY FACILITY.......................................................................................................................................... 7 5.6 LABORATORY LOCATION ....................................................................................................................................... 7 5.7 TEST INSTRUMENTS LIST ....................................................................................................................................... 8 6 TEST RESULTS AND MEASUREMENT DATA ............................................................................................. 9 6.1 ANTENNA REQUIREMENT: ...................................................................................................................................... 9 6.2 CONDUCTED EMISSION ....................................................................................................................................... 10 6.3 CONDUCTED OUTPUT POWER ............................................................................................................................ 13 6.4 OCCUPY BANDWIDTH .......................................................................................................................................... 15 6.5 POWER SPECTRAL DENSITY ............................................................................................................................... 20 6.6 BAND EDGE ......................................................................................................................................................... 22 6.6.1 Conducted Emission Method ..................................................................................................................... 22 6.6.2 Radiated Emission Method ......................................................................................................................... 23 6.7 SPURIOUS EMISSION ........................................................................................................................................... 28 6.7.1 Conducted Emission Method ..................................................................................................................... 28 6.7.2 Radiated Emission Method ......................................................................................................................... 30 7 TEST SETUP PHOTO..................................................................................................................................... 35 8 EUT CONSTRUCTIONAL DETAILS.............................................................................................................. 37 Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 3 of 37

Report No: CCIS14100084802 4 Test Summary Test Item Section in CFR 47 Section Result Antenna requirement 15.203/15.247 (c) RSS-210,RSS-GEN Pass AC Power Line Conducted Emission 15.207 RSS-210,RSS-GEN Pass Conducted Peak Output Power 15.247 (b)(3) RSS-210,RSS-GEN Pass 6dB Emission Bandwidth 15.247 (a)(2) RSS-210,RSS-GEN Pass Power Spectral Density 15.247 (e) RSS-210,RSS-GEN Pass Band Edge 15.247(d) RSS-210,RSS-GEN Pass Spurious Emission 15.205/15.209 RSS-210,RSS-GEN Pass Pass: The EUT complies with the essential requirements in the standard. Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 4 of 37

Report No: CCIS14100084802 5 General Information 5.1 Client Information Applicant: Binatone Electronics International Limited Address of Applicant: Floor 23A, 9 Des Voeux Road West, Sheung Wan, Hong Kong Manufacturer: ShenZhen Concox Information Technology Co., Ltd Address of Manufacturer: 4F, Building B, Gaoxinqi Industrial Park, Liuxian 1st Road, District 67,Bao’an, Shenzhen, Guangdong, China Factory: Huizhou Goldenchip Electronics Co., Ltd Address of Factory: No. 12 Factory, Songyang Road, Zhongkai Hi-tech Development Zone, Huizhou City, Guangdong Province, China 5.2 General Description of E.U.T. Product Name: DECT Phone Model No.: Smart 63, KS7106 Operation Frequency: 2402-2480 MHz Channel numbers: 40 Channel separation: 2 MHz Modulation technology: GFSK Data speed : 1Mbps Antenna Type: Internal Antenna Antenna gain: 0 dBi Power supply: Rechargeable Li-ion Battery DC3.7V 1100mAh AC adapter: Model:MLF-A00060501000U0021 Input:100-240VAC,50/60Hz 0.18A Output:5.0VDC MAX1A The Model: Smart 63, KS7106 were identical inside, the electrical Remark: circuit design, layout, components used and internal wiring,with only difference being model name. Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 5 of 37

Report No: CCIS14100084802 Operation Frequency each of channel Channel Frequency Channel Frequency Channel Frequency Channel Frequency 0 2402MHz 10 2422MHz 20 2442MHz 30 2462MHz 1 2404MHz 11 2424MHz 21 2444MHz 31 2464MHz 2 2406MHz 12 2426MHz 22 2446MHz 32 2466MHz 3 2408MHz 13 2428MHz 23 2448MHz 33 2468MHz 4 2410MHz 14 2430MHz 24 2450MHz 34 2470MHz 5 2412MHz 15 2432MHz 25 2452MHz 35 2472MHz 6 2414MHz 16 2434MHz 26 2454MHz 36 2474MHz 7 2416MHz 17 2436MHz 27 2456MHz 37 2476MHz 8 2418MHz 18 2438MHz 28 2458MHz 38 2478MHz 9 2420MHz 19 2440MHz 29 2460MHz 39 2480MHz Note: In section 15.31(m), regards to the operating frequency range over 10 MHz, the Lowest frequency, the middle frequency, and the highest frequency of channel were selected to perform the test, and the selected channel see below: Channel Frequency The lowest channel 2402MHz The middle channel 2442MHz The Highest channel 2480MHz Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 6 of 37

Report No: CCIS14100084802 5.3 Test environment and mode Operating Environment: Temperature: 24.0 C Humidity: 54 % RH Atmospheric Pressure: 1010 mbar Test mode: Operation mode Keep the EUT in continuous transmitting with modulation The sample was placed 0.8m above the ground plane of 3m chamber. Measurements in both horizontal and vertical polarities were performed. During the test, each emission was maximized by: having the EUT continuously working, investigated all operating modes, rotated about all 3 axis (X, Y & Z) and considered typical configuration to obtain worst position, manipulating interconnecting cables, rotating the turntable, varying antenna height from 1m to 4m in both horizontal and vertical polarizations. The emissions worst- case are shown in Test Results of the following pages. Duty cycle setting during the transmission is 100% with maximum power setting for all modulations. 5.4 Description of Support Units N/A 5.5 Laboratory Facility The test facility is recognized, certified, or accredited by the following organizations: ● FCC - Registration No.: 817957 Shenzhen Zhongjian Nanfang Testing Co., Ltd. EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in out files. Registration 817957, February 27, 2012. ● IC - Registration No.: 10106A-1 The 3m Semi-anechoic chamber of Shenzhen Zhongjian Nanfang Testing Co., Ltd. has been Registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 10106A-1. ● CNAS - Registration No.: CNAS L6048 Shenzhen Zhongjian Nanfang Testing Co., Ltd. is accredited to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration laboratories for the competence of testing. The Registration No. is CNAS L6048. 5.6 Laboratory Location Shenzhen Zhongjian Nanfang Testing Co., Ltd. Address: No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Tel: +86-755-23118282 Fax: +86-755-23116366 Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 7 of 37

Report No: CCIS14100084802 5.7 Test Instruments list Radiated Emission: Inventory Cal. Date Cal. Due date Item Test Equipment Manufacturer Model No. No. (mm-dd-yy) (mm-dd-yy) 3m Semi- Anechoic 1 SAEMC 9(L)*6(W)* 6(H) CCIS0001 Aug 23 2014 Aug 22 2017 Chamber SCHWARZBECK 2 BiConiLog Antenna VULB9163 CCIS0005 Apr 19 2014 Apr 19 2015 MESS-ELEKTRONIK Double -ridged SCHWARZBECK 3 BBHA9120D CCIS0006 Apr 19 2014 Apr 19 2015 waveguide horn MESS-ELEKTRONIK 4 EMI Test Software AUDIX E3 N/A N/A N/A 5 Coaxial Cable CCIS N/A CCIS0016 Apr. 01 2014 Mar. 31 2015 6 Coaxial Cable CCIS N/A CCIS0017 Apr. 01 2014 Mar. 31 2015 7 Coaxial cable CCIS N/A CCIS0018 Apr. 01 2014 Mar. 31 2015 8 Coaxial Cable CCIS N/A CCIS0019 Apr. 01 2014 Mar. 31 2015 9 Coaxial Cable CCIS N/A CCIS0087 Apr. 01 2014 Mar. 31 2015 Amplifier(10kHz- 10 HP 8447D CCIS0003 Apr. 01 2014 Mar. 31 2015 1.3GHz) Amplifier(1GHz- Compliance Direction 11 PAP-1G18 CCIS0011 June 09 2014 June 08 2015 18GHz) Systems Inc. Pre-amplifier AFS33-18002 12 Rohde & Schwarz GTS218 Apr. 01 2014 Mar. 31 2015 (18-26GHz) 650-30-8P-44 13 Horn Antenna ETS-LINDGREN 3160 GTS217 Mar. 30 2014 Mar. 29 2015 14 Printer HP HP LaserJet P1007 N/A N/A N/A 15 Positioning Controller UC UC3000 CCIS0015 N/A N/A Spectrum analyzer 16 Rohde & Schwarz FSP CCIS0023 Apr 19 2014 Apr 19 2015 9k-30GHz 17 EMI Test Receiver Rohde & Schwarz ESPI CCIS0022 Apr 01 2014 Mar. 31 2015 18 Loop antenna Laplace instrument RF300 EMC0701 Apr 01 2014 Mar. 31 2015 Universal radio 19 Rhode & Schwarz CMU200 CCIS0069 May. 29 2014 May. 28 2015 communication tester 20 Signal Analyzer Rohde & Schwarz FSIQ3 CCIS0088 Apr 19 2014 Apr 19 2015 Conducted Emission: Inventory Cal. Date Cal. Due date Item Test Equipment Manufacturer Model No. No. (mm-dd-yy) (mm-dd-yy) 1 Shielding Room ZhongShuo Electron 11.0(L)x4.0(W)x3.0(H) CCIS0061 Oct 10 2012 Oct 09 2015 2 EMI Test Receiver Rohde & Schwarz ESCI CCIS0002 Apr 10 2014 Apr 09 2015 3 LISN CHASE MN2050D CCIS0074 Apr 10 2014 Apr 10 2015 4 Coaxial Cable CCIS N/A CCIS0086 Apr. 01 2014 Mar. 31 2015 5 EMI Test Software AUDIX E3 N/A N/A N/A Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 8 of 37

Report No: CCIS14100084802 6 Test results and Measurement Data 6.1 Antenna requirement: Standard requirement: FCC Part15 C Section 15.203 /247(c) and RSS-Gen Section 7.1.2 15.203 requirement: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. 15.247(c) (1)(i) requirement: (i) Systems operating in the 2400-2483.5 MHz band that is used exclusively for fixed. Point-to-point operations may employ transmitting antennas with directional gain greater than 6dBi provided the maximum conducted output power of the intentional radiator is reduced by 1 dB for every 3 dB that the directional gain of the antenna exceeds 6dBi. E.U.T Antenna: The antenna is an internal antenna which cannot replace by end-user, the best case gain of the antenna is 0 dBi. Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 9 of 37

Report No: CCIS14100084802 6.2 Conducted Emission Test Requirement: FCC Part15 C Section 15.207 and RSS-Gen Section 7.1.4 Test Method: ANSI C63.4: 2003 Test Frequency Range: 150 kHz to 30 MHz Class / Severity: Class B Class B Receiver setup: RBW=9kHz, VBW=30kHz Limit: Limit (dBuV) Frequency range (MHz) Quasi-peak Average 0.15-0.5 66 to 56* 56 to 46* 0.5-5 56 46 5-30 60 50 * Decreases with the logarithm of the frequency. Test procedure 1. The E.U.T and simulators are connected to the main power through a line impedance stabilization network (L.I.S.N.), which provides a 50ohm/50uH coupling impedance for the measuring equipment. 2. The peripheral devices are also connected to the main power through a LISN that provides a 50ohm/50uH coupling impedance with 50ohm termination. (Please refer to the block diagram of the test setup and photographs). 3. Both sides of A.C. line are checked for maximum conducted interference. In order to find the maximum emission, the relative positions of equipment and all of the interface cables must be changed according to ANSI C63.4: 2003 on conducted measurement. Test setup: Test Instruments: Refer to section 5.7 for details Test mode: Refer to section 5.3 for details Test results: Passed Measurement Data Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 10 of 37

CuI3 GOLMI (dBuV) 70 co FCC CLASS—B P sols ® FCC CLASS—B AV 40 ‘ 4 30 | i \ Mc( alus id 20 10 0 —10 0.150.2 0.5 1 2 5 10 20 30 Hrace:A Frequency (MHz) Site : CCIS Shielding Room Condition : FCC CLASS—B QP LISN NEUTRAL Job. no : 848RF EUT : DECT Phone Model : Smart 63 Test Mode : BLE mode Power Rating : AC 1209/60Hz Environment : Temp: 23 °C Huni:§6® Atmos:10!KPa Test Engineer: A—bomb Read LISN Cable Limit Over Freq Level Factor Loss Level Line Limit Remark MHz dBu¥ dB dB dBu¥ dBu¥ dB 1 .150 §5.41 0.25 0.00 §5.66 66.00 —10.34 QP 2 0.150 39.40 0.25 0.00 39.65 56.00 —16.35 Average 2 0.182 §0.83 0.25 0.00 §1.08 64.42 —13.34 QP 4 0.198 33.55 0.25 0.00 33.80 53.71 —19.91 Average 5 0.230 46.80 0.25 0.00 47.05 62.44 —15.39 QP 6 0.238 46.28 0.25 0.00 46.53 62.17 —15.64 QP T 0.238 27.03 0.25 0.00 27.28 52.17 —24.89 Average 8 0.286 43.17 0.26 0.00 43.43 60.63 —17.20 QP 9 0.289 24.06 0.26 0.00 24.32 50.54 —26.22 Average 10 0.337 22.77 0.26 0.00 23.03 49.27 —26.24 Average 11 0. 386 22.20 0.25 0.00 22.45 48.17 —25.72 Average 12 .686 38.09 0.19 0.00 38.28 56.00 —17.72 QP

Report No: CCIS14100084802 Line: Notes: 1. An initial pre-scan was performed on the live and neutral lines with peak detector. 2. Quasi-Peak and Average measurement were performed at the frequencies with maximized peak emission. 3. Final Level =Receiver Read level + LISN Factor + Cable Loss Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 12 of 37

Report No: CCIS14100084802 6.3 Conducted Output Power Test Requirement: FCC Part15 C Section 15.247 (b)(3) and RSS-210 A8.4 section 4 Test Method: ANSI C63.4:2003 and KDB 558074D01 v03r02 / RSS-Gen section 4.8 Limit: 30dBm Test setup: Test Instruments: Refer to section 5.7 for details Test mode: Refer to section 5.3 for details Test results: Passed Test method refer to KDB 558074D01 v03r02 (DTS Measure Guidance) Remark: section 9.2.2.2 Measurement Data Test CH Maximum Conducted Output Power (dBm) Limit(dBm) Result Lowest -1.22 Middle -0.57 30.00 Pass Highest -0.98 Test plot as follows: Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 13 of 37

Report No: CCIS14100084802 Test mode: GFSK Marker 1 [T1] RBW 1 MHz RF Att 30 dB Ref Lvl -1.22 dBm VBW 3 MHz 20.5 dBm 2.40210521 GHz SWT 5 ms Unit dBm 20 0.5 dB Offset 1 [T1] -1.22 dBm A 2.40210521 GHz 10 1 0 -10 1MAX 1MA -20 -30 -40 -50 -60 -70 Center 2.402 GHz 500 kHz/ Span 5 MHz Date: 15.OCT.2014 20:41:37 Lowest channel Marker 1 [T1] RBW 1 MHz RF Att 30 dB Ref Lvl -0.57 dBm VBW 3 MHz 20.5 dBm 2.44215531 GHz SWT 5 ms Unit dBm 20 0.5 dB Offset 1 [T1] -0.57 dBm A 2.44215531 GHz 10 1 0 -10 1MAX 1MA -20 -30 -40 -50 -60 -70 Center 2.442 GHz 500 kHz/ Span 5 MHz Date: 15.OCT.2014 20:42:44 Middle channel Marker 1 [T1] RBW 1 MHz RF Att 30 dB Ref Lvl -0.98 dBm VBW 3 MHz 20.5 dBm 2.48009519 GHz SWT 5 ms Unit dBm 20 0.5 dB Offset 1 [T1] -0.98 dBm A 2.48009519 GHz 10 1 0 -10 1MAX 1MA -20 -30 -40 -50 -60 -70 Center 2.48 GHz 500 kHz/ Span 5 MHz Date: 15.OCT.2014 20:43:18 Highest channel Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 14 of 37

Report No: CCIS14100084802 6.4 Occupy Bandwidth Test Requirement: FCC Part15 C Section 15.247 (a)(2) and RSS-210 section A8.2(a) Test Method: ANSI C63.4:2003 and KDB 558074D01 v03r02 / RSS-Gen section 4.6.2 Limit: >500kHz Test setup: Test Instruments: Refer to section 5.7 for details Test mode: Refer to section 5.3 for details Test results: Passed Measurement Data Test CH 6dB Emission Bandwidth (MHz) Limit(kHz) Result Lowest 0.76 Middle 0.76 >500 Pass Highest 0.76 Test CH 99% Occupy Bandwidth (MHz) Limit(kHz) Result Lowest 1.04 Middle 1.04 N/A N/A Highest 1.04 Test plot as follows: Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 15 of 37

CCIS Report No: CCIS14100084802 Test mode:6dB EBW GFSK ®um 02 ut # 4F L0 Centee 2.¢0r ave we w Lowest channel B me un M us Wo $o BP hm n Centee z.err on we w Middle channel B me in Ms WPs $o BP hR N we w Highest channel Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B—C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bac‘an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 16 of 37

CGUI3

Report No: CCIS14100084802 Test mode:99% OBW GFSK Marker 1 [T1] RBW 100 kHz RF Att 30 dB Ref Lvl -1.97 dBm VBW 300 kHz 20.5 dBm 2.40200501 GHz SWT 5 ms Unit dBm 20 0.5 dB Offset 1 [T1] -1.97 dBm A 2.40200501 GHz 10 OPB 1.04208417 MHz T1 [T1] -14.81 dBm 0 1 2.40149399 GHz T2 [T1] -15.62 dBm 2.40253607 GHz -10 1MAX T1 T2 1MA -20 -30 -40 -50 -60 -70 Center 2.402 GHz 500 kHz/ Span 5 MHz Date: 15.OCT.2014 20:46:08 Lowest channel Marker 1 [T1] RBW 100 kHz RF Att 30 dB Ref Lvl -1.32 dBm VBW 300 kHz 20.5 dBm 2.44225551 GHz SWT 5 ms Unit dBm 20 0.5 dB Offset 1 [T1] -1.32 dBm A 2.44225551 GHz 10 OPB 1.04208417 MHz T1 [T1] -14.06 dBm 0 1 2.44149399 GHz T2 [T1] -14.96 dBm 2.44253607 GHz -10 1MAX T1 T2 1MA -20 -30 -40 -50 -60 -70 Center 2.442 GHz 500 kHz/ Span 5 MHz Date: 15.OCT.2014 20:45:17 Middle channel Marker 1 [T1] RBW 100 kHz RF Att 30 dB Ref Lvl -1.69 dBm VBW 300 kHz 20.5 dBm 2.48025551 GHz SWT 5 ms Unit dBm 20 0.5 dB Offset 1 [T1] -1.69 dBm A 2.48025551 GHz 10 OPB 1.04208417 MHz T1 [T1] -14.74 dBm 0 1 2.47949399 GHz T2 [T1] -15.58 dBm 2.48053607 GHz -10 1MAX T1 T2 1MA -20 -30 -40 -50 -60 -70 Center 2.48 GHz 500 kHz/ Span 5 MHz Date: 15.OCT.2014 20:44:20 Highest channel Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 18 of 37

CGUI3

Report No: CCIS14100084802 6.5 Power Spectral Density Test Requirement: FCC Part15 C Section 15.247 (e) and FCC Part15 C Section 15.247 (e) ANSI C63.4:2003 and KDB 558074D01 v03r02 / RSS-210 section A8.2 Test Method: (b) Limit: 8 dBm Test setup: Test Instruments: Refer to section 5.7 for details Test mode: Refer to section 5.3 for details Test results: Passed Measurement Data Test CH Power Spectral Density (dBm) Limit(dBm) Result Lowest -1.94 Middle -1.33 8.00 Pass Highest -1.70 Test plots as follow: Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 20 of 37

Report No: CCIS14100084802 Test mode: GFSK ®ume Canng BB L0 0. Centee 2.¢0r ave wo e Lowest channel ®am 0Ons # 4H L0 Certer z.arr on m Middle channel B me ua Cs Wt BP Tt ts we w Highest channel Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B—C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bac‘an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 21 of 37

CCIS Report No: CCIS14100084802 6.6 Band Edge 6.6.1 Conducted Emission Method Test Requirement: FCC Part15 C Section 15.247 (d) and RSS—210 section A8.5 Test Method: ANSI €63.4:2003 and KDB 558074D01 v03r02 / RSS—210 section A8.5 Limit: In any 100 kHz bandwidth outside the frequency band in which the spread spectrum intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement. Test setup: Spectrum Analyzer ooo ooo soo SaQ E.U.T Non—Conducted Table Ground Reference Plane Test Instruments: Refer to section 5.7 for details Test mode: Refer to section 5.3 for details Test results: Passed Test plots as follow: Test mode: GFSK nackee 1. iil 100 k ar are 20 as nackee 1. iil new 100 kz ar ace 20 as ree wl ~sa.e7 gon 300 inz ret un sn on oo vaw dco ks zo.s aon rassresse oxe $ ne unie don zo.5 don soemmce es mut 328 me unie don oo ow oo see Ganter 2.3955 oi 123 mey span 13 m stace 2.478 one 22 me/ stom 2. on oate 1s.o0r. zo8 rocseczo cate 1s.o0r.zor8 zosecto Lowest channel Highest channel Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B—C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bac‘an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 22 of 37

Report No: CCIS14100084802 6.6.2 Radiated Emission Method Test Requirement: FCC Part15 C Section 15.209 and 15.205 and RSS-210 section A8.5 Test Method: ANSI C63.4: 2003 / RSS-Gen section 4.9 Test Frequency Range: 2.3GHz to 2.5GHz Test site: Measurement Distance: 3m Receiver setup: Frequency Detector RBW VBW Remark Peak 1MHz 3MHz Peak Value Above 1GHz Peak 1MHz 10Hz Average Value Limit: Frequency Limit (dBuV/m @3m) Remark 54.00 Average Value Above 1GHz 74.00 Peak Value Test Procedure: 1. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter camber. The table was rotated 360 degrees to determine the position of the highest radiation. 2. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. 3. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. 4. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rota table was turned from 0 degrees to 360 degrees to find the maximum reading. 5. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. 6. If the emission level of the EUT in peak mode was 10 dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10 dB margin would be re-tested one by one using peak, quasi- peak or average method as specified and then reported in a data sheet. Test setup: Test Instruments: Refer to section 5.7 for details Test mode: Refer to section 5.3 for details Test results: Passed Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 23 of 37

Report No: CCIS14100084802 Test channel: Lowest Horizontal: Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 24 of 37

Report No: CCIS14100084802 Test channel: Lowest Vertical: Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 25 of 37

Report No: CCIS14100084802 Test channel: Highest Horizontal: Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 26 of 37

Report No: CCIS14100084802 Test channel: Highest Vertical: Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 27 of 37

Report No: CCIS14100084802 6.7 Spurious Emission 6.7.1 Conducted Emission Method Test Requirement: FCC Part15 C Section 15.247 (d) and RSS-210 section A8.5 Test Method: ANSI C63.4:2003 and KDB 558074D01 v03r02 / RSS-210 section A8.5 Limit: In any 100 kHz bandwidth outside the frequency band in which the spread spectrum intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement. Test setup: Test Instruments: Refer to section 5.7 for details Test mode: Refer to section 5.3 for details Test results: Passed Test plot as follows: Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 28 of 37

CCIS Report No: CCIS14100084802 Test mode: GFSK Lowest channel orte: s nov aore re:a3i80 SOMHz~25GHz Middle channel petecon w on rmsscin S0MHz~25GHz Highest channel orte: snov.zoe recsuse SOMHz~25GHz Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B—C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bac‘an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 29 of 37

Report No: CCIS14100084802 6.7.2 Radiated Emission Method Test Requirement: FCC Part15 C Section 15.209 and 15.205 and RSS-Gen section 4.9 Test Method: ANSI C63.4:2003 / RSS-Gen section 4.9 Test Frequency Range: 9KHz to 25GHz Test site: Measurement Distance: 3m Receiver setup: Frequency Detector RBW VBW Remark 30MHz-1GHz Quasi-peak 120KHz 300KHz Quasi-peak Value Peak 1MHz 3MHz Peak Value Above 1GHz Peak 1MHz 10Hz Average Value Limit: Frequency Limit (dBuV/m @3m) Remark 30MHz-88MHz 40.0 Quasi-peak Value 88MHz-216MHz 43.5 Quasi-peak Value 216MHz-960MHz 46.0 Quasi-peak Value 960MHz-1GHz 54.0 Quasi-peak Value 54.0 Average Value Above 1GHz 74.0 Peak Value Test Procedure: 1. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter camber. The table was rotated 360 degrees to determine the position of the highest radiation. 2. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. 3. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. 4. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rota table was turned from 0 degrees to 360 degrees to find the maximum reading. 5. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. 6. If the emission level of the EUT in peak mode was 10 dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10 dB margin would be re-tested one by one using peak, quasi- peak or average method as specified and then reported in a data sheet. Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 30 of 37

Report No: CCIS14100084802 Test setup: Below 1GHz Above 1GHz Test Instruments: Refer to section 5.7 for details Test mode: Refer to section 5.3 for details Test results: Passed Remark: 1. Pre-scan all kind of the place mode (X-axis, Y-axis, Z-axis), and found the Y-axis is the worst case. 2. 9 kHz to 30MHz is too low, so only shows the data of above 30MHz in this report. Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 31 of 37

Report No: CCIS14100084802 Below 1GHz Horizontal: Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 32 of 37

Report No: CCIS14100084802 Vertical: Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 33 of 37

Report No: CCIS14100084802 Above 1GHz Test channel: Lowest Level: Peak Read Antenna Cable Preamp Over Frequency Level Limit Line Level Factor Loss Factor Limit Polarization (MHz) (dBuV/m) (dBuV/m) (dBuV) (dB/m) (dB) (dB) (dB) 4804.00 47.23 31.53 8.90 40.24 47.42 74.00 -26.58 Vertical 4804.00 46.14 31.53 8.90 40.24 46.33 74.00 -27.67 Horizontal Test channel: Lowest Level: Average Read Antenna Cable Preamp Over Frequency Level Limit Line Level Factor Loss Factor Limit Polarization (MHz) (dBuV/m) (dBuV/m) (dBuV) (dB/m) (dB) (dB) (dB) 4804.00 37.89 31.53 8.90 40.24 38.08 54.00 -15.92 Vertical 4804.00 36.34 31.53 8.90 40.24 36.53 54.00 -17.47 Horizontal Test channel: Middle Level: Peak Read Antenna Cable Preamp Over Frequency Level Limit Line Level Factor Loss Factor Limit Polarization (MHz) (dBuV/m) (dBuV/m) (dBuV) (dB/m) (dB) (dB) (dB) 4884.00 46.21 31.58 8.98 40.15 46.62 74.00 -27.38 Vertical 4884.00 46.47 31.58 8.98 40.15 46.88 74.00 -27.12 Horizontal Test channel: Middle Level: Average Read Antenna Cable Preamp Over Frequency Level Limit Line Level Factor Loss Factor Limit Polarization (MHz) (dBuV/m) (dBuV/m) (dBuV) (dB/m) (dB) (dB) (dB) 4884.00 36.85 31.58 8.98 40.15 37.26 54.00 -16.74 Vertical 4884.00 36.49 31.58 8.98 40.15 36.90 54.00 -17.10 Horizontal Test channel: Highest Level: Peak Read Antenna Cable Preamp Over Frequency Level Limit Line Level Factor Loss Factor Limit Polarization (MHz) (dBuV/m) (dBuV/m) (dBuV) (dB/m) (dB) (dB) (dB) 4960.00 46.41 31.69 9.08 40.03 47.15 74.00 -26.85 Vertical 4960.00 47.10 31.69 9.08 40.03 47.84 74.00 -26.16 Horizontal Test channel: Highest Level: Average Read Antenna Cable Preamp Over Frequency Level Limit Line Level Factor Loss Factor Limit Polarization (MHz) (dBuV/m) (dBuV/m) (dBuV) (dB/m) (dB) (dB) (dB) 4960.00 36.18 31.69 9.08 40.03 36.92 54.00 -17.08 Vertical 4960.00 37.88 31.69 9.08 40.03 38.62 54.00 -15.38 Horizontal Remark: 1. Final Level =Receiver Read level + Antenna Factor + Cable Loss – Preamplifier Factor 2. The emission levels of other frequencies are very lower than the limit and not show in test report. Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCIS141000848RF No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 34 of 37


Document Created: 2014-12-31 09:47:19
Document Modified: 2014-12-31 09:47:19
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC