Test Report

FCC ID: VLJ-SH036

Test Report

Download: PDF
FCCID_4301416

GC ds Ah Attestatlonof Global Compliance 7 H 1 JX Report No.: AGC00275190401FEO3 Page 36 of 67 8—DPSK MODULATION IN HIGH CHANNEL Hopping off zs Keysight Spectrum Analyzer — Swept SA [—=~][—&~(wsu) i AF 509 aC |_ SENSE—TNT | ALreN auto _| 480010167006 Avg Type: Log—Pwr Trace W FPosk Search PNO: Fast C,) Trig: Free Run AvglHold:>100/100 TveU IFGain:Low Atten: 30 dB oe i Next Peak 1LU gB.‘dIV Ref 20.00 dBm MKR] MODE TRC SCL FUNCTION FUNCTION WiDTH FUNCTIONVALUE * 1e P480 pem B912 Em A n14[f] 2.483 500 0 GHz 42.376 dBm|__________|[_ 4 io Mkr—RefLvl 6 6 7 8 9 10 11 Eollee — mso STATUS Hopping on s Keysight Spectrum Analyzer — Swept SA 0 RF 509 aC \ SENSE—TNT | ALTGN AUTO 5 6169205640 Avg Type: Log—Pwr PNO: Fast C,) Trig: Free Run AvgiHold:>100/100 IFGain:Low Atten: 30 dB Next Peak 10 dBE/div Ref 20.00 dBm (eF+ MKR] MODE TRC SCL FUNCTION FUNCTION WiDTH FUNCTION VALUE @ l N4f| PB473 169 2 GHz 4.002 Eemer 2 IBEAEA 2.483 500 0 GHz 43.971 dBm|__________|[_ i 40 © c —o e t Mkr—RefLvl * us w =a 8 a = a& The results shbwuivin thisftestreport refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. The document is issued by/AGC, this docufgeht cannot be reproduced except in full with our prior written permission. The more details and the authenticity of the report will be confirmed Athittp://www.agc@eit.com. Attestatiqrtof Global Compliance Tel: +86—755 2908 1955 Fax: +86—755 2600 8484 E—mail: agc@age—cert.com 400 089 2118 Add: 2/F. , Building 2, No.1—4, Chaxi Sanwei Technical Industrial Park,Gushu, Xixiang, Bacan District, Shenzhen, Guangdong China

Report No.: AGC00275190401FE03 Page 37 of 67 10. RADIATED EMISSION 10.1. MEASUREMENT PROCEDURE 1. The EUT was placed on the top of the turntable 0.8 or 1.5 meter above ground. The phase center of the receiving antenna mounted on the top of a height-variable antenna tower was placed 3 meters far away from the turntable. 2. Power on the EUT and all the supporting units. The turntable was rotated by 360 degrees to determine the position of the highest radiation. 3. The height of the broadband receiving antenna was varied between one meter and four meters above ground to find the maximum emissions field strength of both horizontal and vertical polarization. 4. For each suspected emissions, the antenna tower was scan (from 1 M to 4 M) and then the turntable was rotated (from 0 degree to 360 degrees) to find the maximum reading. 5. Set the test-receiver system to Peak or CISPR quasi-peak Detect Function with specified bandwidth under Maximum Hold Mode. 6. For emissions above 1GHz, use 1MHz RBW and 3MHz VBW for peak reading. Place the measurement antenna away from each area of the EUT determined to be a source of emissions at the specified measurement distance, while keeping the measurement antenna aimed at the source of emissions at each frequency of significant emissions, with polarization oriented for maximum response. The measurement antenna may have to be higher or lower than the EUT, depending on the radiation pattern of the emission and staying aimed at the emission source for receiving the maximum signal. The final measurement antenna elevation shall be that which maximizes the emissions. The measurement antenna elevation for maximum emissions shall be restricted to a range of heights of from 1 m to 4 m above the ground or reference ground plane. 7. When the radiated emissions limits are expressed in terms of the average value of the emissions, and pulsed operation is employed, the measurement field strength shall be determined by averaging over one complete pulse train, including blanking intervals, as long as the pulse train does not exceed 0.1 seconds. As an alternative (provided the transmitter operates for longer than 0.1 seconds) or in cases where the pulse train exceeds 0.1 seconds, the measured field strength shall be determined from the average absolute voltage during a 0.1 second interval during which the field strength is at its maximum values. 8.If the emissions level of the EUT in peak mode was 3 dB lower than the average limit specified, then testing will be stopped and peak values of EUT will be reported, otherwise, the emissions which do not have 3 dB margin will be repeated one by one using the quasi-peak method for below 1GHz. 9. For testing above 1GHz, the emissions level of the EUT in peak mode was lower than average limit (that means the emissions level in peak mode also complies with the limit in average mode), then testing will be stopped and peak values of EUT will be reported, otherwise, the emissions will be measured in average mode again and reported. 10. In case the emission is lower than 30MHz, loop antenna has to be used for measurement and the recorded data should be QP measured by receiver. High - Low scan is not required in this case.

Report No.: AGC00275190401FE03 Page 38 of 67 The following table is the setting of spectrum analyzer and receiver. Spectrum Parameter Setting Start ~Stop Frequency 9KHz~150KHz/RB 200Hz for QP Start ~Stop Frequency 150KHz~30MHz/RB 9KHz for QP Start ~Stop Frequency 30MHz~1000MHz/RB 120KHz for QP 1GHz~26.5GHz Start ~Stop Frequency 1MHz/3MHz for Peak, 1MHz/3MHz for Average Receiver Parameter Setting Start ~Stop Frequency 9KHz~150KHz/RB 200Hz for QP Start ~Stop Frequency 150KHz~30MHz/RB 9KHz for QP Start ~Stop Frequency 30MHz~1000MHz/RB 120KHz for QP

Report No.: AGC00275190401FE03 Page 39 of 67 10.2. TEST SETUP Radiated Emission Test-Setup Frequency Below 30MHz RADIATED EMISSION TEST SETUP 30MHz-1000MHz RADIATED EMISSION TEST SETUP ABOVE 1000MHz

Report No.: AGC00275190401FE03 Page 40 of 67 10.3. LIMITS AND MEASUREMENT RESULT 15.209 Limit in the below table has to be followed Frequencies Field Strength Measurement Distance (MHz) (micorvolts/meter) (meters) 0.009~0.490 2400/F(KHz) 300 0.490~1.705 24000/F(KHz) 30 1.705~30.0 30 30 30~88 100 3 88~216 150 3 216~960 200 3 Above 960 500 3 Note: All modes were tested For restricted band radiated emission, the test records reported below are the worst result compared to other modes. 10.4. TEST RESULT RADIATED EMISSION BELOW 30MHZ No emission found between lowest internal used/generated frequencies to 30MHz.

® A\G & T 1 i# "|I Faikeg Attestation of Global Compliance Report No.: AGC00275190401FEO3 Page 41 of 67 RADIATED EMISSION BELOW 1GHZ EUT Bluetooth Headset Model Name SHO36 0 Relative & Temperature 25°C Humidity 55.4% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 4 Antenna Horizontal 66.9 dBu¥/m Limit: —— Margin: — 27 4MMW 1 2 3 13 30.000 127.00 224.00 321.00 418.00 515.00 612.00 709.00 806. 00 1000.00 MHz \y|ik] Freq. |Reading] Factor |Measurement] Limit Over Detemwflrl?[;?; Comment MHz dBu\V dBim dBuV‘m dBuVim| dB cm degree 1 445500 O.56 1993 2049 |40.00 |19.51| peak 2 1415500 O# i923 2014 |4350|—23.36) peak 3 287.0500 093 1977 2070 |45.00 |—25.30| peak 4 eargess 154 28.01 29.55 |46.00 |16.45| peak 5 206.0000 254 3049 3303 |45.00 |12.97) peak 6 * q4sz667 268 3212 .80 |46.00 |11.20| peak RESULT: PASS The results ’mSticor| o thisfesost report refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. The document is issued by/A C§€ this docu/fi it cannot be reproduced except in full with our prior written permission. The more details and the authenticity of the report will be confirmed tfittp://www.agc-% t.com. o Attestatic m ® ) i Tel: +86—755 2908 1955 Fax: +86—755 2600 8484 E—mail: agc@age—cert.com @ 400 089 2118 iN¥ Add: 2/F. , Building 2, No.1—4, Chaxi Sanwei Technical Industrial Park,Gushu, Xixiang, Bacan District, Shenzhen, Guangdong China

® A\G & T 1 i# "|I Faikeg Attestation of Global Compliance Report No.: AGC00275190401FEO3 Page 42 of 67 EUT Bluetooth Headset Model Name SHO36 0 Relative i Temperature 25°C Humidity 55.4% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 4 Antenna Vertical 66.9 dBu¥/m Limit: —— Margin: _ _ »y 3 3W SMWM 1 2 13 30.000 127.00 224.00 321.00 418.00 515.00 612.00 709.00 806. 00 1000.00 MHz pyp[Mk] Freq |Reading| Factor |Measurement] Limit Over DHMMHE"Q’;’DL;*; Comment MHz dBuy dBim dBuWim dBuVim dB om degree 1 494000 065 1975 2040 |40.00 |—19.60| peak 2 1480167 083 1921 2004 |43.50 |—2346| peak 3 6265500 143 2727 2870 |45.00 |17.30| peak 4 Ti5456r 101 2850 2951 |45.00 |—16.49| peak 5 810.8500 219 30.55 2274 |46.00 |13.26| peak 6 * 9224000 228 3189 417 —|45.00 |11.83| peak RESULT: PASS Note: 1. Factor=Antenna Factor + Cable loss, Margin=Measurement—Limit. 2. All test modes had been pre—tested. The mode 4 is the worst case and recorded in the report. The results ,n' & virl fii@;}" kreport refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. The document is issued by/A C§€ this docu/fi it cannot be reproduced except in full with our prior written permission. The more details and the authenticity of the report will be confirmed a tfittp://www.agc-% t.com. o Attestatic m ® ) i Tel: +86—755 2908 1955 Fax: +86—755 2600 8484 E—mail: agc@age—cert.com @ 400 089 2118 iN¥ Add: 2/F. , Building 2, No.1—4, Chaxi Sanwei Technical Industrial Park,Gushu, Xixiang, Bacan District, Shenzhen, Guangdong China

Report No.: AGC00275190401FE03 Page 43 of 67 RADIATED EMISSION ABOVE 1GHZ EUT Bluetooth Headset Model Name SH036 Temperature 25°C Relative Humidity 55.4% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 1 Antenna Horizontal Frequency Meter Reading Factor Emission Level Limits Margin Value Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 4804.062 47.68 3.76 51.44 74.00 -22.56 peak 4804.062 44.88 3.76 48.64 54.00 -5.36 AVG 7206.093 38.38 8.17 46.55 74.00 -27.45 peak 7206.093 33.88 8.17 42.05 54.00 -11.95 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. EUT Bluetooth Headset Model Name SH036 Temperature 25°C Relative Humidity 55.4% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 1 Antenna Vertical Frequency Meter Reading Factor Emission Level Limits Margin Value Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 4804.062 50.08 3.76 53.84 74.00 -20.16 peak 4804.062 43.82 3.76 47.58 54.00 -6.42 AVG 7206.093 37.88 8.17 46.05 74.00 -27.95 peak 7206.093 36.77 8.17 44.94 54.00 -9.06 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier.

Report No.: AGC00275190401FE03 Page 44 of 67 EUT Bluetooth Headset Model Name SH036 Temperature 25°C Relative Humidity 55.4% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 2 Antenna Horizontal Frequency Meter Reading Factor Emission Level Limits Margin Value Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 4882.062 47.06 3.78 50.84 74.00 -23.16 peak 4882.062 43.00 3.78 46.78 54.00 -7.22 AVG 7323.093 39.79 8.23 48.02 74.00 -25.98 peak 7323.093 37.44 8.23 45.67 54.00 -8.34 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. EUT Bluetooth Headset Model Name SH036 Temperature 25°C Relative Humidity 55.4% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 2 Antenna Vertical Frequency Meter Reading Factor Emission Level Limits Margin Value Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 4882.062 47.57 3.78 51.35 74.00 -22.65 peak 4882.062 44.64 3.78 48.42 54.00 -5.58 AVG 7323.093 40.42 8.23 48.65 74.00 -25.35 peak 7323.093 36.82 8.23 45.05 54.00 -8.95 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier.

Report No.: AGC00275190401FE03 Page 45 of 67 EUT Bluetooth Headset Model Name SH036 Temperature 25°C Relative Humidity 55.4% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 3 Antenna Horizontal Frequency Meter Reading Factor Emission Level Limits Margin Value Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 4960.062 46.66 3.81 50.47 74.00 -23.53 peak 4960.062 44.26 3.81 48.07 54.00 -5.94 AVG 7440.093 39.68 8.27 47.95 74.00 -26.05 peak 7440.093 37.71 8.27 45.98 54.00 -8.02 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. EUT Bluetooth Headset Model Name SH036 Relative Temperature 25°C 55.4% Humidity Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 3 Antenna Vertical Frequency Meter Reading Factor Emission Level Limits Margin Value Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 4960.062 46.66 3.81 50.47 74.00 -23.53 peak 4960.062 44.83 3.81 48.64 54.00 -5.36 AVG 7440.093 39.37 8.27 47.64 74.00 -26.36 peak 7440.093 36.95 8.27 45.22 54.00 -8.78 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. RESULT: PASS Note: Other emissions from 1G to 25 GHz are considered as ambient noise. No recording in the test report. Factor = Antenna Factor + Cable loss - Amplifier gain, Over=Measure-Limit. The “Factor” value can be calculated automatically by software of measurement system. All test modes had been tested. The GFSK modulation is the worst case and recorded in the report.

Report No.: AGC00275190401FE03 Page 46 of 67 TEST RESULT FOR RESTRICTED BANDS REQUIREMENTS EUT Bluetooth Headset Model Name SH036 Temperature 25°C Relative Humidity 55.4% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 1 Antenna Horizontal PK AV RESULT: PASS

Report No.: AGC00275190401FE03 Page 47 of 67 EUT Bluetooth Headset Model Name SH036 Temperature 25°C Relative Humidity 55.4% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 1 Antenna Vertical PK AV RESULT: PASS

Report No.: AGC00275190401FE03 Page 48 of 67 EUT Bluetooth Headset Model Name SH036 Temperature 25°C Relative Humidity 55.4% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 3 Antenna Horizontal PK AV RESULT: PASS

Report No.: AGC00275190401FE03 Page 49 of 67 EUT Bluetooth Headset Model Name SH036 Temperature 25°C Relative Humidity 55.4% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 3 Antenna Vertical PK AV RESULT: PASS Note: The factor had been edited in the “Input Correction” of the Spectrum Analyzer. So the Amplitude of test plots is equal to Reading level plus the Factor in dB. Use the A dB(μV) to represent the Amplitude. Use the F dB(μV/m) to represent the Field Strength. So A=F. All test modes had been pre-tested. The GFSK modulation is the worst case and recorded in the report.

&TI&i ® micg A\G Attestation of Global Compliance Report No.: AGC00275190401FEO3 Page 50 of 67 11. NUMBER OF HOPPING FREQUENCY 11.1. MEASUREMENT PROCEDURE The EUT shall have its hopping function enabled. Use the following spectrum analyzer settings: 1. Span: The frequency band of operation. Depending on the number of channels the device supports, it may be necessary to divide the frequency range of operation across multiple spans, to allow the individual channels to be clearly seen. 2. RBW: To identify clearly the individual channels, set the RBW to less than 30% of the channel spacing or the 20 dB bandwidth, whichever is smaller. 3. VBW >z RBW. Sweep: Auto. Detector function: Peak. Trace: Max hold. 4. Allow the trace to stabilize. 11.2. TEST SETUP (BLOCK DIAGRAM OF CONFIGURATION) Same as described in section 8.2 11.3. MEASUREMENT EQUIPMENT USED The same as described in section 6 11.4. LIMITS AND MEASUREMENT RESULT MEASUREMENT HO-:;(:II:IG- Z(H)A(')\JEEL LIMIT (NO. OF CH) (NO. OF CH) RESULT >=15 79 PASS TEST PLOT FOR NO. OF TOTAL CHANNELS sz Keysight Spectrum Analyzer — Swept SA [+=~][ «& (w3u) |_ SENSE—TNT | ALreN auto _| es Start Freq 2.400000000 GHz . Avg Type: Log—Pwr w d PNO: Fast C,) Trig: FreeRun AvgiHold:>100/100 Tirrrrreeeee IFGain:Low Atten: 30 dB Ref 20.00 dBm StartFreq 2.400000000 GHz Start 240000 GHz Stop 248350 GHz #Res BW 100 kHz uce uLo Sweep 7.992 ms (1000 pts) mso STATUS Note: The GFSK modulation is the worst case and recorded in the report. The results ,u' & virl fii@;}" report refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. The document is issued by/A 6§€ this doc(@ it cannot be reproduced except in full with our prior written permission. The more details and the authenticity of the report will be confirmed tfittp://www.agc-«& t.com. o Attestatic m o i Tel: +86—755 2908 1955 Fax: +86—755 2600 8484 E—mail: agc@age—cert.com @ 400 089 2118 & Add: 2/F. , Building 2, No.1—4, Chaxi Sanwei Technical Industrial Park,Gushu, Xixiang, Bacan District, Shenzhen, Guangdong China

&TI&i ® micg A\G Attestation of Global Compliance Report No.: AGC00275190401FEO3 Page 51 of 67 12. TIME OF OCCUPANCY (DWELL TIME) 12.1. MEASUREMENT PROCEDURE The EUT shall have its hopping function enabled. Use the following spectrum analyzer settings: 1. Span: Zero span, centered on a hopping channel. 2. RBW shall be=channel spacing and where possible RBW should be set >> 1 / T, where T is the expected dwell time per channel. 3. Sweep: As necessary to capture the entire dwell time per hopping channel; where possible use a video trigger and trigger delay so that the transmitted signal starts a little to the right of the start of the plot. The trigger level might need slight adjustment to prevent triggering when the system hops on an adjacent channel; a second plot might be needed with a longer sweep time to show two successive hops on a channel. 4. Detector function: Peak. Trace: Max hold. 5. Use the marker—delta function to determine the transmit time per hop. 6. Repeat the measurement using a longer sweep time to determine the number of hops over the period specified in the requirements. The sweep time shall be equal to, or less than, the period specified in the requirements. Determine the number of hops over the sweep time and calculate the total number of hops in the period specified in the requirements, using the following equation: {(Number of hops in the period specified in the requirements) = {number of hops on spectrum analyzer) x (period specified in the requirements / analyzer sweep time) 7. The average time of occupancy is calculated from the transmit time per hop multiplied by the number of hops in the period specified in the requirements. 12.2. TEST SETUP (BLOCK DIAGRAM OF CONFIGURATION) Same as described in section 8.2 12.3. MEASUREMENT EQUIPMENT USED The same as described in section 6 12.4. LIMITS AND MEASUREMENT RESULT Ti f Pul Channel m;iroDH: se Number of hops in the period Sweep Time Limit specified in the requirements (ms) (ms) (ms) Low 2.927 27*4 316.116 400 Middle 2.918 26*4 303.472 400 High 2.917 26*4 303.368 400 Note: The 8—DPSK modulation is the worst case and recorded in the report. The results ’m,6tison| o thisfeaes report refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. The document is issued by/A 6§€ this doc(fiao it cannot be reproduced except in full with our prior written permission. The more details and the authenticity of the report will be confirmed t;!?ttp://www.agc-«drS t.com. o Tel: +86—755 2908 1955 Fax: +86—755 2600 8484 E—mail: agc@age—cert.com @ 400 089 2118 Add: 2/F. , Building 2, No.1—4, Chaxi Sanwei Technical Industrial Park,Gushu, Xixiang, Bacan District, Shenzhen, Guangdong China

Report No.: AGC00275190401FE03 Page 52 of 67 TEST PLOT OF LOW CHANNEL

Report No.: AGC00275190401FE03 Page 53 of 67 TEST PLOT OF MIDDLE CHANNEL

Report No.: AGC00275190401FE03 Page 54 of 67 TEST PLOT OF HIGH CHANNEL

&TI&i ® micg A\G Attestation of Global Compliance Report No.: AGC00275190401FEO3 Page 55 of 67 13. FREQUENCY SEPARATION 13.1. MEASUREMENT PROCEDURE The EUT shall have its hopping function enabled. Use the following spectrum analyzer settings: 1. Span: Wide enough to capture the peaks of two adjacent channels. 2. RBW: Start with the RBW set to approximately 30%of the channel spacing; adjust as necessary to best identify the center of each individual channel. 3. Video (or average) bandwidth (VBW) > RBW. 4. Sweep: Auto. e) Detector function: Peak. f) Trace: Max hold. g) Allow the trace to stabilize. Use the marker—delta function to determine the separation between the peaks of the adjacent channels. 13.2. TEST SETUP (BLOCK DIAGRAM OF CONFIGURATION) Same as described in section 6.2 13.3. MEASUREMENT EQUIPMENT USED The same as described in section 6.3 13.4. LIMITS AND MEASUREMENT RESULT pHANNEE LIMIT RESULT CHANNEL SEPARATION KHz KHz Pass CHO1—CHO2 1006 >=25 KHz or 2/3 20 dB BW TEST PLOT FOR FREQUENCY SEPARATION CL Keysight Spectrum Analyzer — Swept SA l+=] +2 —(itu) |__sensemt I ALTGN AUTO _ e Start Freq 2.400000000 GHz . Avg Type: Log—Pwr w ¥ PNO: Wide C ) > Tg: Free Run AvgiHold:>100/100 Tc IFGain:Low Atten: 30 dB Ref 20.00 dEBm StartFreq 2400000000 GHz Start 2400000 GHz Stop 2405000 GHz fRes BW 30 kHz #VBW 100 kHz Sweep 5.328 ms (1000 pts) | MKR] MODE TRC SCL X Y FUNCTION FUNCTION WiDTH FUNCTION VALUE & l n11|f| 2402 002 GHz 4.099 dBm|__________| lll-_ 008 GHz|_____4.179 dBm|_________| 3 |___| [U & msa STATUS o Etisort thisjea C is issued by 6§€ this doc@ it cannot be reproduced except in full with our prior written permission. The more details and the authenticity of the report will be confirmed tfittp://www.agc-«& t.com. o Attestatic m o i Tel: +86—755 2908 1955 Fax: +86—755 2600 8484 E—mail: agc@age—cert.com @ 400 089 2118 & Add: 2/F. , Building 2, No.1—4, Chaxi Sanwei Technical Industrial Park,Gushu, Xixiang, Bacan District, Shenzhen, Guangdong China

Report No.: AGC00275190401FE03 Page 56 of 67 APPENDIX A: PHOTOGRAPHS OF TEST SETUP RADIATED EMISSION TEST SETUP BELOW 1GHZ RADIATED EMISSION TEST SETUP ABOVE 1GHZ

Report No.: AGC00275190401FE03 Page 57 of 67 APPENDIX B: PHOTOGRAPHS OF EUT ALL VIEW OF EUT TOP VIEW OF EUT

Report No.: AGC00275190401FE03 Page 58 of 67 BOTTOM VIEW OF EUT FRONT VIEW OF EUT

Report No.: AGC00275190401FE03 Page 59 of 67 BACK VIEW OF EUT \ LEFT VIEW OF EUT

Report No.: AGC00275190401FE03 Page 60 of 67 RIGHT VIEW OF EUT OPEN VIEW OF EUT-1(Left)

Report No.: AGC00275190401FE03 Page 61 of 67 OPEN VIEW OF EUT-2 VIEW OF BATTERY

Report No.: AGC00275190401FE03 Page 62 of 67 INTERNAL VIEW OF EUT-1 INTERNAL VIEW OF EUT-2

Report No.: AGC00275190401FE03 Page 63 of 67 INTERNAL VIEW OF EUT-3 Antenna INTERNAL VIEW OF EUT-4

Report No.: AGC00275190401FE03 Page 64 of 67 OPEN VIEW OF EUT-1(Right) OPEN VIEW OF EUT-2

Report No.: AGC00275190401FE03 Page 65 of 67 VIEW OF BATTERY INTERNAL VIEW OF EUT-1

Report No.: AGC00275190401FE03 Page 66 of 67 INTERNAL VIEW OF EUT-2 INTERNAL VIEW OF EUT-3

Report No.: AGC00275190401FE03 Page 67 of 67 INTERNAL VIEW OF EUT-4 ----END OF REPORT----


Document Created: 2019-05-31 18:13:44
Document Modified: 2019-05-31 18:13:44
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC