RF Exposure Info

FCC ID: VLJ-CN50PU

RF Exposure Info

Download: PDF
FCCID_4369177

Produkte Products Prüfbericht - Nr.: 50263230 001 Seite 24 von 26 Test Report No. Page 24 of 26 6 Safety Human Exposure 6.1 Radio Frequency Exposure Compliance 6.1.1 Electromagnetic Fields RESULT: Pass Test Specification Test standard : CFR47 FCC Part 2: Section 2.1091 CFR47 FCC Part 1: Section 1.1310 FCC KDB Publication 447498 v06 FCC KDB Publication 865664 D01 v01r04 FCC KDB Publication 865664 D02 v01r02 RSS-102 Issue 5 March 2015  FCC requirements FCC requirement: Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess limit for maximum permissible exposure. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as a mobile device whereby a distance of 20cm normally can be maintained between t he user and the device. MPE Calculation Method according to KDB 865664 D01 Power Density: S(mW/cm2)= PG/4πR2 or EIRP/4πR2 Where: S = power density (mW/cm 2) P = power input to the antenna (mW) G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna (cm) The nominal maximum conducted output power specified: 2.4GHz FHSS: 20.00 dBm From the peak RF output power, the minimum mobile separation distance, d=20 cm, as well as the antenna gain (Max. 0.0 dBi for 2.4GHz FHSS), the RF power density can be calculated as below: For 2.4GHz FHSS: S(mW/cm2)= PG/4πR2 = 0.020 mW/cm2 Limits for Maximum Permissible Exposure (MPE) according to FCC Part 1.1310: 1.0 mW/cm2

Produkte Products Prüfbericht - Nr.: 50263230 001 Seite 25 von 26 Test Report No. Page 25 of 26  IC requirements: The EUT shall comply with the requirement of RSS-102 section 2.5.2. Exemption from Routine Evaluation Limits – RF Exposure Evaluation RF exposure evaluation is required if the separation distance between the user and/or bystander and the device’s radiating element is greater than 20 cm, except when the device operates as follows: at or above 300 MHz and below 6 GHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 1.31 x 10-2 ƒ0.6834 W (adjusted for tune-up tolerance), where ƒ is in MHz;  RF exposure evaluation exempted power for 2.4GHz FHSS: 2.670 W The nominal maximum conducted output power specified: 2.4GHz FHSS: 20.00 dBm Antenna Gain: 0.0 dBi for 2.4GHz FHSS The Max. e.i.r.p. for 2.4GHz FHSS: 20.00 dBm = 0.100 W The e.i.r.p. for 2.4GHz FHSS is less than the RF exposure evaluation exempted power. So RF exposure evaluation is not required. “RF Radiation Exposure Statement Caution: This Transmitter must be installed to provide a separation distance of at least 20 cm from all persons.”


Document Created: 2019-06-21 17:18:15
Document Modified: 2019-06-21 17:18:15
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC