SAR attachment 9D

FCC ID: V65SCP-27H

RF Exposure Info

Download: PDF
FCCID_1073306

FCC ID: V65SCP-27H Appendix D: Dipole Calibration Parameters Dipole Calibration Parameters Model: SCP-2700

9ltpg, Calibration Laboratory of / Schweizerischer Kalibrierdienst Schmid & Partner R Service suisse d‘étalonnage Engineering AG ipcovra To s Servizio svizzero di taratura 6 j x \wy a Zeughausstrasse 43, 8004 Zurich, Switzerland */fi\‘x\ Swiss Calibration Service "hilai® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Client Object Calibration procedure(s) Callbration date: Condition of the calibrated item This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter EPM—442A GB37480704 04—Oct—07 (No. 217—00736) Oct—08 Power sensor HP 8481A US37292783 04—Oct—07 (No. 217—00736) Oct—08 Reference 20 dB Attenuator SN: 5086 (208) 01—Jul—08 (No. 217—00864) Jul—09 Type—N mismatch combination SN: 5047.2 / 06327 01—Jul—08 (No. 217—00867) Jul—09 Reference Probe ES3DV2 SN: 3025 28—Apr—08 (No. ES3—3025_Apr08) Apr—09 DaAE4 SN: 601 14—Mar—08 (No. DAE4—601_Mar08) Mar—09 Secondary Standards ID # Check Date (in house) Scheduled Check Power sensor HP 8481A MY41092317 18—Oct—02 (in house check Oct—07) In house check: Oct—09 RF generator R&S SMT—06 100005 4—Aug—99 (in house check Oct—07) In house check: Oct—09 Network Analyzer HP 8753E US37390585 $4206 18—Oct—01 (in house chack Oct—07) In house check: Oct—08 Namé Function ignature Calibrated by: Approved by: issued: September 16, 2008 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: DB35V2—467_SepO8 Page 1 of 9

Calibration Laboratory of i9n Schweizerischer Kalibrierdienst a sSa=y /. S Schmid & Partner m I“flifi’ll C Service suisse d‘étalonnage Engineering AG Py W § Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland {'/,, m s S Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x.y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2003, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", December 2003 b) IEC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz)", February 2005 Federal Communications Commission Office of Engineering & Technology (FCC OET}, "Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields; Additional Information for Evaluating Compliance of Mobile and Portable Devices with FCC Limits for Human Exposure to Radiofrequency Emissions", Supplement C (Edition 01—01) to Bulletin 65 Additional Documentation: d) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented paralle! to the body axis. Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. Certificate No: D835V2—467_SepO8 Page 2 of 9

Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY5 V5.0 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom V4.9 Distance Dipole Center — TSL 15 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 835 MHz £ 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 41.5 0.90 mho/m Measured Head TSL parameters (22.0 £0.2) °C 41.2 46 % 0.88 mho/m # 6 % Head TSL temperature during test (22.0 £0.2) °C — ——— SAR result with Head TSL SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 250 mW input power 2.35 mW /g SAR normalized normalized to 1W 9.40 mW /g SAR for nominal Head TSL parameters ‘ normalized to 1W 9.35 mW / g 17.0 % (k=2) SAR averaged over 10 cm‘ (10 g) of Head TSL condition SAR measured 250 mW input power 1.54 mW /g SAR normalized normalized to 1W 6.16 mW /g SAR for nominal Head TSL parameters ‘ normalized to 1W 6.12 mW / g £ 16.5 % (k=2) ‘ Correction to nominal TSL parameters according to d), chapter "SAR Sensitivities" Certificate No: DB35V2—467_SepO8 Page 3 of 9

Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 55.2 0.97 mho/m Measured Body TSL parameters (22.0 £ 0.2) °C 53.3 £ 6 % 1.01 mho/m £ 6 % Body TSL temperature during test (21.7 £0.2) °C ——— — SAR result with Body TSL SAR averaged over 1 cm‘ (1 g) of Body TSL Condition SAR measured 250 mW input power 249 mW /g SAR normalized normalized to 1W 9.96 mW /g SAR for nominal Body TSL parameters * normalized to 1W 9.49 mW / g £17.0 % (k=2) SAR averaged over 10 cm‘ (10 g) of Body TSL condition SAR measured 250 mW input power 1.64 mWw 1g SAR normalized normalized to 1W 6.56 mWw /g SAR for nominal Body TSL parameters * normalized to 1W 6.34 mW / g # 16.5 % (k=2) * Correction to nominal TSL parameters according to d), chapter "SAR Sensitivities" Certificate No: DB3GV2—467_SepO8 Page 4 of 9

Appendix Antenna Parameters with Head TSL Impedance, transformed to feed point 47.3 Q 1.7 jQ Return Loss —29.6 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 45.3 Q —5.1 jQ Return Loss — 22.8 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.363 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on August 27, 2002 Certificate No: D835V2—467_SepO8 Page 5 of 9

DASYS Validation Report for Head TSL Date/Time: 12.09.2008 12:33:15 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 835 MHz; Type: D835V2; Serial: D835V2 — SN:467 Communication System: CW—835; Frequency: 835 MHz; Duty Cycle: 111 Medium: HSL 900 MHz Medium parameters used: f= 835 MHz; 0 = 0.9 mho/m; &, = 41.2; p = 1000 kg/m‘ Phantom section: Flat Section Measurement Standard: DASYS5 (IEEE/IEC) DASYS5 Configuration: e Probe: ESSDV2 — SN3025; ConvF(5.97, 5.97, 5.97); Calibrated: 28.04.2008 e Sensor—Surface: 3.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 14.03.2008 e Phantom: Flat Phantom 4.9L; Type: QD00OP49AA; Serial: 1001 e Measurement SW: DASY5, V5.0 Build 119; SEMCAD X Version 13.2 Build 87 Pin=250mW; dip=15mm; dist=3.4mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 55.6 V/m; Power Drift = 0.018 dB Peak SAR (extrapolated) = 3.44 Wikg SAR(1 g) = 2.35 mWig; SAR(10 g) = 1.54 mWig Maximum value of SAR (measured) = 2.65 mW/g 0 dB = 2.665mWig Certificate No: DB35V2—467_SepO8 Page 6 of 9

Impedance Measurement Plot for Head TSL 12 Sep 2008 §8:54147 sa1 i uors an4 7.260 a ~1.6 112.82 pF £35.000 500 MHz CH1 Markens Del 2:89,.566 o 16.328 a Cor 900.000 MHz fivg 16 835.000 000 MHz _ CH2 Markers Cor 2:—10,854 dB 900.000 MHz Ay '1.59 SThRT 635.000 608MHz SToP 1100.000 000 Wz Certificate No: DB35V2—467_SepO8 Page 7 of 9

DASYS5 Validation Report for Body TSL Date/Time: 16.09.2008 10:27:28 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 835 MHz; Type: D835V2; Serial: D835V2 — SN:467 Communication System: CW; Frequency: 835 MHz; Duty Cycle: 1:1 Medium: MSL900 Medium parameters used: £= 835 MHz; 0 = 1.01 mho/m; £, = 53.3; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASYS5 (IEEE/IEC) DASYS Configuration: e Probe: ESSDV2 — SN3025; ConvF(5.9, 5.9, 5.9); Calibrated: 28.04.2008 e Sensor—Surface: 3.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 14.03.2008 e Phantom: Flat Phantom 4.9L; Type: QDO0OP49AA; Serial: 1001 e Measurement SW: DASY5, V5.0 Build 119; SEMCAD X Version 13.2 Build 87 Pin = 250mW, d = 15mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 53.9 V/m; Power Drift = 0.046 dB Peak SAR (extrapolated) = 3.61 W/kg SAR(1 g) = 2.49 mW/g; SAR(10 g) = 1.64 mW/g Maximum value of SAR (measured) = 2.79 mW/g dB 0 13 0 dB = 2.79mWig Certificate No: D835V2—467_SepO8 Page 8 of 9

Impedance Measurement Plot for Body TSL 16 Sep 2008 @9:01:56 CHZ sii EBd 4 uiors 4t 45.273 6 —5.097 a 37.991 pF 8©35.000 600 MHz CH1 Markers Bel 2 54.469 n 29,291 o Cor $00.000 MHz fivg 16 CH2 S$1 LOG S dB/REF —20 dB ___ 1:—22.753 dB $35.000 000 MHz_ CH2 Markers 21—11,278 dB Cor 900.000 MHz fivg 16 START 635.000 600 MHz sToP 1 188.000 ob hz Certificate No: D835V2—467_SepO8 Page 9 of 9

Calibration Laboratory of S Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates _ Client Object Calibration procedure(s) Calibration date: Condition of the callbrated item This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Calibrated by, Certificate No.) Scheduled Calibration Power meter EPM—442A GB37480704 04—Oct—07 (No. 217—00736) Oct—08 Power sensor HP 8481A US37202783 04—Oct—07 (No. 217—00736) Oct—08 Reference 20 0B Attenuator SN: 5086 (20g) 01—Jul—08 (No. 217—00864) Jul—09 Type—N mismatch combination SN: 5047.2 / 06327 01—Jul—08 (No. 217—00867) Jul—09 Reference Probe ES3DV2 SN: 3025 28—Apr—08 (No. ES3—3025_Apr08) Apr—08 DAE4 SN: 601 14—Mar—08 (No. DAE4—601_Mar08) Mar—09 Secondary Standards ID # Check Date (in house) Scheduled Check Power sensor HP B4B1A MY41092317 18—Oct—02 (in house check Oct—07) In house check: Oct—09 RF generator R&S SMT—06 100005 4—Aug—99 (in house check Oct—07) in house check: Oct—09 Network Analyzer HP 8753E US373900585 S4206 18—Oct—01 (in house check Oct—07) In house check: Oct—08 Name Function Signature Callbrated by: . Approved by: issued: September 17, 2008 This calibration cerfificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: D1900V2—54016_SepO8 Page 1 of 9

Calibration Laboratory of \\Q\\'é/ § Schweizerischer Kalibrierdienst Schmid & Partner ;’fifi c Service suisse d‘étalonnage Engineering AG z //—\\ > Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland €4,/fi\‘§3 S Swiss Calibration Service Athilubt Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multitateral Agreementfor the recognition of calibration certificates Glossary: TSL tissue simulating liquid Convr sensitivity in TSL / NORM x.y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2003, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", December 2003 b) CENELEC EN 50361, "Basic standard for the measurement of Specific Absorption Rate related to human exposure to electromagnetic fields from mobile phones (300 MHz — 3 GHz), July 2001 Federal Communications Commission Office of Engineering & Technology (FCC OET}, "Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields; Additional Information for Evaluating Compliance of Mobile and Portable Devices with FCC Limits for Human Exposure to Radiofrequency Emissions", Supplement C (Edition 01—01) to Bulletin 65 Additional Documentation: d) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. Certificate No: D1900V2—5d016_Sep08 Page 2 of 9

Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASYS V5.0 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom V5.0 Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 1900 MHz#1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 40.0 1.40 mho/m Measured Head TSL parameters (22.0 £ 0.2) °C 40.7 £6 % 1.47 mho/m # 6 % Head TSL temperature during test (21.5 £0.2) °C ——— ———— SAR result with Head TSL SAR averaged over 1 cm‘ (1 g) of Head TSL condition SAR measured 250 mW input power 10.3 mW /g SAR normalized normalized to 1W 41.2 mW / g SAR for nominal Head TSL parameters ‘ normalized to 1W 40.6 mW / g £17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL Condition SAR measured 250 mW input power 5.37 mW !g SAR normalized normalized to 1W 21.5 mWw /g SAR for nominal Head TSL parameters ‘ normalized to 1W 21.4 mW / g £ 16.5 % (k=2) * Correction to nominal TSL parameters according to d), chapter "SAR Sensitivities" Certificate No: D1900V2—50016_SepO8 Page 3 of 9

Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 53.3 1.52 mho/m Measured Body TSL parameters (22.0 £ 0.2) °C 521 #6% 1.6 mho/m # 6 % Body TSL temperature during test (21.5 £0.2) °C ———— ——— SAR result with Body TSL SAR averaged over 1 cm‘ ({1 g) of Body TSL Condition SAR measured 250 mW input power 10.2 mW /g SAR normalized normalized to 1W 40.8 mW /g SAR for nominal Body TSL parameters * normalized to 1W 39.1 mW / g & 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 250 mW input power 5.31 mW /g SAR normalized normalized to 1W 21.2 mW /g SAR for nominal Body TSL parameters * normalized to 1W 20.8 mW / g * 16.5 % (k=2) * Correction to nominal TSL parameters according to d), chapter "SAR Sensitivities® Certificate No: D1900V2—5d016_SepO8 Page 4 of 9

Appendix Antenna Parameters with Head TSL impedance, transformed to feed point §51.9 Q + 4.5 jOQ Return Loss —26.4 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 47.0 0 + 4.8 jQ Return Loss —24.7 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.195 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on June 04, 2002 Certificate No: D1900V2—5d016_Sep08 Page 5 of 9

DASYS5 Validation Report for Head TSL Date/Time: 11.09.2008 14:48:18 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 1900 MHz; Type: D1900V2; Serial: D1900V2 — SN:504016 Communication System: CW; Frequency: 1900 MHz; Duty Cycle: 1:1 Medium: HSL U1O BB Medium parameters used: £= 1900 MHz; 0 = 1.47 mho/m; &, = 40.7; p = 1000 kg/m‘ Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC) DASYS5 Configuration: Probe: ES3DV2 — SN3025; ConvF(4.9, 4.9, 4.9); Calibrated: 28.04.2008 Sensor—Surface: 3.4mm (Mechanical Surface Detection) Electronics: DAE4 Sn601; Calibrated: 14.03.2008 Phantom: Flat Phantom 5.0 (front); Type: QDOOOP50AA; Serial: 1001 Measurement SW: DASY5, V5.0 Build 119; SEMCAD X Version 13.2 Build 87 Pin = 250 mW; dip = 10 mm, scan at 3.4mm/Zoom Scan (dist=3.4mm, probe Odeg) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 93.2 V/m; Power Drift = 0.00747 dB Peak SAR (extrapolated)= 19 W/kg SAR(1 g) = 10.3 mW/g; SAR(10 g) = 5.37 mW/g Maximum value of SAR (measured) = 12.2 mW/g 0 dB =12.2mW/g Certificate No: D1900V2—5d016_SepO8 Page 6 of 9

Impedance Measurement Plot for Head TSL 41 Sep 2008 11:06153 si1 i uors 2 51.904 o 377.76 pH 1 990.500 000 MHz CH1 Mapkers Del 4: 46.000 a ~15,408 a tor 1.90000 GHz fivg 16 t CH2 CH2 Markers 1:—15,.678 dB Cor 1.80000 BHz Ay 16° 4 START 1 £00.000 000 MHz P 2 186.000908MBz Certificate No: D1900V2—5d016_SepO8 Page 7 of 9

DASY5 Validation Report for Body TSL Date/Time: 15.09.2008 14:13:19 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 1900 MHz; Type: D1900V2; Serial: D1900V2 — SN:504016 Communication System: CW; Frequency: 1900 MHz; Duty Cycle: 1:1 Medium: MSL U1O BB Medium parameters used: £= 1900 MHz; 0 = 1.6 mho/m; &.= 52.1; p = 1000 kg/m‘ Phantom section: Flat Section Measurement Standard: DASYS5 (IEEE/IEC) DASYS5 Configuration: e Probe: ES3DV2 — SN3025; ConvF(4.5, 4.5, 4.5); Calibrated: 28.04.2008 Sensor—Surface: 3.4mm (Mechanical Surface Detection) Electronics: DAE4 Sn601; Calibrated: 14.03.2008 e Phantom: Flat Phantom 5.0 (back); Type: QDOOOP50AA; Serial: 1002 e Measurement SW: DASY35, V5.0 Build 119; SEMCAD X Version 13.2 Build 87 Pin = 250 mW; dip = 10 mm, scan at 3.4mm/Zoom Scan (dist=3.4mm, probe Odeg) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value= 91.3 V/m; Power Drift = 0.00376 dB Peak SAR (extrapolated) = 18.3 W/kg SAR(I g) =10.2 mW/g; SAR(10 g) = 5.31 mW/ig Maximum value of SAR (measured) = 12.5 mW/g dB 8 0 dB=12.5mWi/g Certificate No: D1900V2—50016_SepO8 Page 8 of 9

Impedance Measurement Plot for Body TSL 15 Sep 2008 10:28:12 $11 1 U FS 2: 47.009 a 4.?45? 4 405.99 pH 1 $00.000 000 MHz CH1 Markers Oe l 1t 422418 a ~16.305 a Cor 1.99000 SHz Fiv 159 q CH2 CH2 Markers 13—1.4,392 dB Car 160000 oH= Aiv 169 START 1 500.000 000 WHz sToP 2 108.000 Boo HMHz Certificate No: D1900V2—5d4016_SepO8 Page 9 of 9

& R w9 1t Calibration Laboratory of i‘\\‘\\\\_//\//fi?’; S Schweizerischer Kalibrierdienst Schmid & Partner ibfi&é Ij c Service suisse d‘étalonnage Engineering AG Ps 9 J g Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland ;/fi\\\\? (/eRp:\\ S swiss Calibration Service *hialabet Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client Object Callbration procedure(s) Calibration date: Condition of the calibrated item This calibration certificate documents the traceability to national standards, which realize the physicalunits of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Caltbration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power mater EPM—442A GB37480704 04—Oct—07 (No. 217—00736) Oct—08 Power sensor HP 8481A US37202783 04—Oct—07 (No. 217—00736) Oct—08 Reference 20 dB Attenuator SN: 5086 (20g) 07—Aug—07 (No 217—00718) Aug—08 Type—N mismatch combination SN: 5047.2 / 06327 08—Aug—07 (No. 217—00721) Aug—08 Reference Probe ES3DV2 SN: 3025 01—Mar—08 (No. ES3—3025_Mar08) Mar—09 DAE4 SN: 601 14—Mar—08 (No. DAE4—601_MarD8) Mar—09 Secondary Standards 1D # Check Date (in house) Scheduled Check Power sensor HP 8481A MY41092317 18—Oct—02 (in house check Oct—07) in house check: Oct—08 RF generator R&S SMT—06 100005 4—Aug—99 (in house check Oct—07) in house check: Oct—09 Network Analyzer HP 8753E US37300585 S4206 18—Oct—01 (in house check Oct—07) In house check: Oct—08 Nam Ful Calibrated by: Approved by: Issued: April 23, 2008 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: D2450V2—776_Apr08 Page 1 of 6

Calibration * Laboratory of ps\“\‘&'fl"‘s Q,\NIS\S\ G Schweizerischer Kalibrierdienst Schmid & Partner ;la\\g/(fi ¢m C Service suisse d‘étalonnage Engineering AG E. ~g 9 Tp g Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland *[oamy (/eRp:\\ S swiss Calibration Service uhi uks Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x.y.z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2003, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", December 2003 b) IEC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz)", February 2005 Federal Communications Commission Office of Engineering & Technology (FCC OET), "Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields; Additional Information for Evaluating Compliance of Mobile and Portable Devices with FCC Limits for Human Exposure to Radiofrequency Emissions", Supplement C (Edition 01—01) to Bulletin 65 Additional Documentation: d) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. Certificate No: D2450V2—776_Apr08 Page 2 of 6

Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY4 V4.7 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom V5.0 Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 2450 MHz # 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 39.2 1.80 mho/m Measured Head TSL parameters (22.0 £ 0.2) °C 39.4 £ 6 % 1.84 mho/m £ 6 % Head TSL temperature during test (21.1 £0.2) °C ——— —— SAR result with Head TSL SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 250 mW input power 13.7 mW /g SAR normalized normalized to 1W 54.8 mW /g SAR for nominal Head TSL parameters ‘ normalized to 1W 54.5 mW ig £ 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 250 mW input power 6.38 mW /g SAR normalized normalized to 1W 25.5 mWw /g SAR for nominal Head TSL parameters ‘ normalized to 1W 25.5 mW ig £ 16.5 % (k=2) * Correction to nominal TSL parameters according to d), chapter "SAR Sensitivities" Certificate No: D2450V2—776_Apr08 Page 3 of 6

Appendix Antenna Parameters with Head TSL Impedance, transformed to feed point 55.3 Q + 9.0 JQ Return Loss —20.1 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.156 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on April 04, 2005 Certificate No: D2450V2—776_Apr08 Page 4 of 6

DASY4 Validation Report for Head TSL Date/Time: 22.04.2008 16:04:49 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN776 Communication System: CW—2450; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium: HSL U1O BB; Medium parameters used: £= 2450 MHz; 0 = 1.83 mho/m; &, = 39.5; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASY4 (High Precision Assessment) DASY4 Configuration: e Probe: ESSDV2 — SN3025; ConvF(4.4, 4.4, 4.4); Calibrated: 01.03.2008 * Sensor—Surface: 3.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 14.03.2008 * Phantom: Flat Phantom 5.0 (front); Type: QDOOOPSOAA; ; e Measurement SW: DASY4, V4.7 Build 55; Postprocessing SW: SEMCAD, V1.8 Build 172 Pin = 250 mW; d = 10 mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 97.5 V/m; Power Drift = 0.031 dB Peak SAR (extrapolated) = 28.2 W/kg SAR(1 g) = 13.7 mW/g; SAR(10 g) = 6.38 mW/ig Maximum value of SAR (measured) = 16.3 mW/g d8 0.000 ~4.60 .20 —23.0 0 dB = 16.3mW/g Certificate No: D2450V2—776_Apr08 Page 5 of 6

Impedance Measurement Plot for Head TSL 22 fpr 2008 14134:06 CHT sit 4 U FS 1: 55.384 n $.0215 n 586.05 pH 2 490.000 000 MHz fvg 16 CH2 S$1 __LOG 1:=20.072 dB. 2450.000 G9B MHz_ Cor fiv 169 i ~~CCENTER ®450.008800 MHz— ~apal 400.000660HHz Certificate No: D2450V2—776_Apr08 Page 6 of 6


Document Created: 2008-12-23 10:35:19
Document Modified: 2008-12-23 10:35:19
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC