SAR attachment 9C

FCC ID: V65SCP-27H

RF Exposure Info

Download: PDF
FCCID_1073305

FCC ID: V65SCP-27H Appendix C: Probe Calibration Parameters Probe Calibration Parameters Model: SCP-2700

Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Object Calibration procedure(s) Calibration date: Condition of the calibrated item This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Callbration Equipment used (M&TE critical for callbration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Fluke Process Calibrator Type 702. SN: 6205803 04—Oct—07 (No: 6467) Oct—08 Keithiey Multimeter Type 2001 SN: 0810278 03—Oct—07 (No: 6465) Oct—08 Secondary Standards ID # Check Date (in house) Scheduled Check Calibrator Box V1.1 SE UMS 006 AB 1004 06—Jun—08 (in house check) In house check: Jun—09 Function Signature Callbrated by: Approved by: Issued: June 25, 2008 This calibration certificate shall not be reproduced exceptin full without written approval of the laboratory. Certificate No: DAE4—602_JunO8 Page 1 of 5

Calibration Laboratory of \\\‘\“\"\Qlj/ul/“/"/, G Schweizerischer Kalibrierdienst Schmid & Partner ;IB\E—/M@E c Service suisse d‘étalonnage Engineering AG P A—2OCS Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzeriand sTwyg 4 N . S : Calibration Swiss ; Service i Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multifateral Agreementfor the recognition of calibration certificates Glossary DAE data acquisition electronics Connector angle information used in DASY system to align probe sensor X to the robot coordinate system. Methods Applied and Interpretation of Parameters * DC Voltage Measurement: Calibration Factor assessed for use in DASY system by comparison with a calibrated instrument traceable to national standards. The figure given corresponds to the full scale range of the voltmeter in the respective range. e Connector angle: The angle of the connector is assessed measuring the angle mechanically by a tool inserted. Uncertainty is not required. e The following parameters as documented in the Appendix contain technical information as a result from the performance test and require no uncertainty. e DC Voltage Measurement Linearity: Verification of the Linearity at +10% and —10% of the nominal calibration voltage. Influence of offset voltage is included in this measurement. e Common mode sensitivity: Influence of a positive or negative common mode voltage on the differential measurement. e Channel separation: Influence of a voltage on the neighbor channels not subject to an input voltage. e AD Converter Values with inputs shorted: Values on the internal AD converter corresponding to zero input voltage * input Offset Measurement: Output voltage and statistical results over a large number of zero voltage measurements. e input Offset Current: Typical value for information; Maximum channel input offset current, not considering the input resistance. * Input resistance: DAE input resistance at the connector, during internal auto—zeroing and during measurement. e Low Battery Alarm Voltage: Typical value for information. Below this voltage, a battery alarm signal is generated. * Power consumption: Typical value for information. Supply currents in various operating modes. Certificate No: DAE4—602_JunO8 Page 2 of 5

DC Voltage Measurement A/D — Converter Resolution nominal High Range: 1LSB = 6.1uV , full range = ~100...+300 mV Low Range: 1LSB = 61nv , full range= ~1....... +3mV DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Calibration Factors X Y Z High Range 404,222 + 0.1% (k=2) 404.494 +0.1% (k=2) 404.631 + 0.1% (k=2) Low Range 3.95815 + 0.7% (k=2) 3.98503+0.7% (k=2) 3.97186 £0.7% (k=2) Connector Angle Connector Angle to be used in DASY system 59°%1° Certificate No: DAE4—602_JunO8 Page 3 of 5

Appendix 1. DC Voltage Linearity High Range Input (rV) Reading (uV) Error (%) Channel X + Input 200000 200000 0.00 Channel X + Input 20000 20004.99 0.02 Channel X « Input 20000 ~19996.75 —0.02 Channel Y + Input 200000 199999.6 0.00 Channel Y + Input 20000 20002.84 0.01 Channel Y — Input 20000 —20000.06 0.00 Channel Z + Input 200000 199999.7 0.00 Channel Z + input 20000 20002.23 0.01 Channel Z = Input 20000 —20001.93 0.01 Low Range Input (1V) Reading (V) Error (%) Channel X + Input 2000 1999.9 0.00 Channel X + Input 200 200.13 0.06 Channel X — Input 200 —200.16 0.08 Channel Y + Input 2000 1999.9 0.00 Channel Y + Input 200 199.47 —0.26 Channel Y — Input 200 —200.33 0.17 Channel Z + Input 2000 1999.9 0.00 Channel Z + input 200 199.12 —0.44 Channel Z — Input 200 —201.13 0.56 2. Common mode sensitivity DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Common mode High Range Low Range Input Voltage {mV) Average Reading {uV) Average Reading (1V) Channel X 200 4.82 4.57 — 200 —2.56 —3.61 Channel Y 200 5.08 5.53 —200 —5.90 —6.32 Channel Z 200 1.61 1.17 —200 —2.53 —242 3. Channel separation DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Input Voltage (mV) Channel X (V) Channel Y (uV) Channel Z (uV) Channel X 200 — 2.23 0.59 Channel Y 200 0.60 — 3.45 Channel Z 200 —1.23 —0.41 — Certificate No: DAE4—602_JunO8 Page 4 of 5

4. AD—Converter Values with inputs shorted DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec High Range (LSB) Low Range (LSB) Channel X 15734 15497 Channel Y 16055 16263 Channel Z 16103 16288 5. Input Offset Measurement DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Input 10MQ Average (1V) min. Offset (1V) max. Offset (1V) Std. I?:‘\Il;ahon Channel X 0.25 —0.72 3.11 0.50 Channel Y ~1.43 —3.28 —0.13 0.47 Channel Z —0.26 —2.94 0.56 0.46 6. Input Offset Current Nominal Input circuitry offset current on all channels: <25fA 7. Input Resistance Zeroing (MOhm) Measuring (MOhm) Channel X 0.2001 199.5 Channel Y 0.2000 199.6 Channel Z 0.2003 199.0 8. Low Battery Alarm Voltage (verified during pre test) Typical values Alarm Level (VDC) Supply (+ Vec) +7.9 Supply (« Vec) —7.6 9. Power Consumption (verified during pre test) Typical values Switched off {mA) Stand by (mA) Transmitting (mA) Supply (+ Vee) +0.0 +6 +14 Supply (— Vec) —0.01 —8 —9 Certificate No: DAE4—602_JunO8 Page 5 of 5

Calibration Laboratory of \&\IJ/;/ Schweizerischer Kalibrierdienst Schmid & Partner M Service sulsse d‘étalonnage Engineering AG T_s Servizio svizzero di taratura 4Ve ny a : Zeughausstrasse 43, 8004 Zurich, Switzerland ",,/fi\\x‘ Swiss Calibration Service "thibals® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multifateral Agreement for the recognition of callbration certificates Client Object Calibration procedure(s) Calibration date: Condition of the callbrated item This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and hurnidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards iD# Cal Date (Certificate No.) Scheduled Calibration Power meter E44198 GB41293874 1—Apr—08 (No. 217—00788) Apr—09 Power sensor E4412A MY41495277 1—Apr—08 (No. 217—00788) Apr—09 Power sensor E4412A MY41498087 1—Apr—08 (No. 217—00788) Apr—09 Reference 3 dB Attenuator SN: S5054 (3c) B—Aug—07 (No. 217—00719) Aug—08 Reference 20 dB Attenuator SN: 55086 (20b) 31—Mar—08 (No. 217—00787) Apr—09 Reference 30 dB Attenuator SN: 85129 (30b) 8—Aug—07 (No. 217—00720) Aug—08 Reference Probe ES3DV2 SN: 3013 2—Jan—08 (No. ES3—3013_Jan08) Jan—08 DaAE4 SN: 660 3—Sep—07 (No. DAE4—660_SepO7) Sep—08 Secondary Standards ID # Check Date (in house) Scheduled Check RF generator HP 8648C Us3642U01700 4—Aug—99 (in house check Oct—07) In house check: Oct—09 Network Analyzer HP 8753E US37390585 18—Oct—01 (in house check Oct—07) In house check: Oct—08 Name __Function Signature Callbrated by: Approved by: Issued: June 25, 2008 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: ET3—1664_JunO8 Page 1 of 9

ip Calibration Laboratory of \“‘\“LI/"“”’A Schweizerischer Kalibrierdienst S\ nz * Schmid & Partner YAunsA Service suisse d‘étalonnage Engineering AG zn Servizio svizzero di taratura wl Zeughausstrasse 43, §004 Zurich, Switzerland by 7 w Swiss Calibration Service Ardnuike® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Mult!lateral Agreementfor the recognition of calibration certificates Glossary: TSL tissue simulating liquid NORMx,y,z sensitivity in free space ConvF sensitivity in TSL / NORMx,.y,z DCP diode compression point Polarization q p rotation around probe axis Polarization 8 8 rotation around an axis that is in the plane normal to probe axis (at measurement center), ie., 8 = 0 is normal to probe axis Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2003, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", December 2003 b) IEC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz)", February 2005 Methods Applied and Interpretation of Parameters: e NORMx,y,z: Assessed for E—field polarization 8 = 0 (f < 900 MHz in TEM—cell; f > 1800 MHz: R22 waveguide). NORMx,y,z are only intermediate values, i.e., the uncertainties of NORMx.y,z does not effect the E—field uncertainty inside TSL (see below ConvF). e NORM(Mx,y,z = NORMx,y,z * frequency_response (see Frequency Response Chart). This linearization is implemented in DASY4 software versions later than 4.2. The uncertainty of the frequency response is included in the stated uncertainty of ConvF. e DCPx,y,z; DCP are numerical linearization parameters assessed based on the data of power sweep (no uncertainty required). DCP does not depend on frequency nor media. e ConvF and Boundary Effect Parameters: Assessed in flat phantom using E—field (or Temperature Transfer Standard for f < 800 MHz) and inside waveguide using analytical field distributions based on power measurements for f > 800 MHz. The same setups are used for assessment of the parameters applied for boundary compensation (alpha, depth) of which typical uncertainty values are given. These parameters are used in DASY4 software to improve probe accuracy close to the boundary. The sensitivity in TSL corresponds to NORMx,y,z * ConvF whereby the uncertainty corresponds to that given for ConvF. A frequency dependent ConvF is used in DASY version 4.4 and higher which allows extending the validity from + 50 MHz to + 100 MHz. e Spherical isotropy (3D deviation from isotropy): in a field of low gradients realized using a flat phantom exposed by a patch antenna. e Sensor Offset: The sensor offset corresponds to the offset of virtual measurement center from the probe tip (on probe axis). No tolerance required. Certificate No: ET3—1664_JunO8 Page 2 of 9

ET3DV6 SN:1664 June 23, 2008 Probe ET3DVC SN:1664 Manufactured: February 8, 2002 Last calibrated: July 16, 2007 Recalibrated: June 23, 2008 Calibrated for DASY Systems (Note: non—compatible with DASY2 system!) Certificate No: ET3—1664_JunO8 Page 3 of 9

ET3DV6 SN:1664 June 23, 2008 DASY — Parameters of Probe: ET3DV6 SN:1664 Sensitivity in Free Spac:eA Diode Compression® NormX 1.90 £101% uV/(V/im) DCP x 92 mV Norm¥Y 1.87 £101% uV/(V/im) DCP Y 96 mV NormZ 1.68 £101% uV/(V/im) DCP zZ 96 mV Sensitivity in Tissue Simulating Liquid (Conversion Factors) Please see Page 8. Boundary Effect TSL 835 MHz Typical SAR gradient: 5 % per mm Sensor Center to Phantom Surface Distance 3.7 mm 4.7 mm SARp, [%l Without Correction Algorithm 11.0 6.9 SARLe [%] With Correction Algorithm 0.8 0.4 TSL 1750 MHz Typical SAR gradient: 10 % per mm Sensor Center to Phantom Surface Distance 3.7 mm 4.7 mm SARL, [%] Without Correction Algorithm 11.2 7.0 SARp, [%] With Correction Algorithm 0.5 0.2 Sensor Offset Probe Tip to Sensor Center 2.7 mm The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. * The uncertainties of NormX,Y,Z do not affect the E*—field uncertainty inside TSL (see Page 8). " Numerical linearization parameter: uncertainty not required. Certificate No: ET3—1664_JunO8 Page 4 of 9

ET3DV6 SN:1664 June 23, 2008 Frequency Response of E—Field (TEM—Cell:ffi110 EXX, Waveguide: R22) _ in _ > _ to Frequency response (normalized) _1 ho _ s _ o o to o t p ~t e & o in 500 1000 1500 2000 2500 3000 f [MHz] [ —o—TEM —o—R22 | Uncertainty of Frequency Response of E—field: £ 6.3% (k=2) Certificate No: ET3—1664_Jun08 Page 5 of 9

ET3DV6 SN:1664 June 23, 2008 Receiving Pattern (¢), 8 = 0° f= 600 MHz, TEM ifi110EXX f= 1800 MHz, WG R22 [—.—X —@—Y¥ —@—Z —O—Tot T 1.0 : |_ as | 9 9 —6—30 MHz | d [ z 0.4 L—-momm | § 0.2 |—0— 600 MHz | 5 g‘g |—@— 1800 MHz | 4 (pg |—a—2500MHz] | —0.6 | 1 o8 [_ —1.0 o 60 120 180 240 300 ¢l Uncertainty of Axial Isotropy Assessment: £ 0.5% (k=2) Certificate No: ET3—1664_Jun08 Page 6 of 9

ET3DV6 SN:1664 June 23, 2008 Dynamic Range f(SARpeaq) (Waveguide R22, f= 1800 MHz) 1.E+06 1.E+05 1.E+04 Input Signal [nVJ 1.E+03 1.E+02 1.2+01 1.E+00 0.0001 0.001 0.01 0.1 10 100 SAR [mW/cm‘] —@— not compensated —&— compensated o o & o Error [dB] o ho ho 6 —0.6 ~1.0 0.001 0.01 0.4 1 10 100 SAR [mW/cm‘] Uncertainty of Linearity Assessment: £ 0.6% (k=2) Certificate No: ET3—1664_JunO8 Page 7 of 9

ET3DV6 SN:1664 June 23, 2008 Conversion Factor Assessment f= 835 MHz, WGLS R9 (head) f= 1750 MHz, WGLS R22 (head) 4.0 ; 80.0 4 | T as . | 3.0 ?Q & T 3 p 2s 3 s 3E. 20 €& 5 §w 150 1.0 :1"\‘%‘ 5 a o.5 PSbg 0.0 L_L_L 1299 °q — 0 20 40 60 0 10 20 30 40 z[mm] z[mm] %Anal;;r:#armmga‘surements ‘ ‘ —O— Analytical fimé—-OA:l\}easurements J f [MHz] Validity [MHz]® TSL Permittivity Conductivity Alpha Depth ConvF Uncertainty 835 £50 / £ 100 Head 41.5£5% 0.90£5% 0.64 2.21 6.47 £11.0% (k=2) 1750 £50/£100 Head 40.1%5% 1.37+5% 0.68 2.02 5.49 £11.0% (k=2) 1900 £50/£100 Head 40.0%25% 140%25% 0.77 1.74 5.08 £11.0% (k=2) 835 + 50/ 100 Body 5§5.215% 0.97+5% 0.62 2.30 6.26 £11.0% (k=2) 1750 £50/£100 Body 53.4%5% 149+5% 0.72 1.91 4.T3 £11.0% (k=2) 1900 £50/£100 Body §3.3+5% 1.52%5% 0.72 1.89 444 £11.0%(k=2) © The validity of £ 100 MHz only applies for DASY v4.4 and higher (see Page 2). The uncertainty is the RSS of the ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band. Certificate No: ET3—1664_Jun08 Page 8 of 9

ET3DV6 SN:1664 June 23, 2008 Deviation from Isotropy in HSL Error (¢, 8), f= 900 MHz 10 0.8 —0.6 0.4 0 0.2 i , o0 5 120E i) 0.4 p 2250 60 50 270 40 9 30 315 20 10 n ; €1—1.00—0.80 ©—0.80——0.60 ©—0.60—0.40 21—0.40—0.20 ©—0,20—0.00 | ©0,00—0.20 0.20—0.40 ©0.40—0.60 ©0.60—0.80 ©0.80—1.00 | Uncertainty of Spherical Isotropy Assessment: £ 2.6% (k=2) Certificate No: ET3—1664_JunO8 Page 9 of 9

Calibration Laboratory of wln Schweizerischer Kalibrierdienst § 3 7 Schmid & Partner Service suisse d‘étalonnage Engineering AG Servizlo svizzero di taratura woi d Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service R 5/ 7 Urdoc uks Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Object Callbration procedure(s) Calibration date: Condition of the calibrated item This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature(22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards __| JD # Cal Date (Certificate No.) Scheduled Calibration Power mater E44198 GB41293874 1—Apr—08 (No. 217—00788) Apr—09 Power sensor E4412A MY41495277 1—Apr—08 (No, 217—00788) Apr—08 Power sensor E4412A MY41498087 1—Apr—08 (No. 217—00788) Apr—09 Reference 3 dB Attenuator SN: 55054 (3c) 8—Aug—07 (No. 217—00719) Aug—08 Reference 20 dB Attenuator SN: S5086 (20b) 31—Mar—08 (No. 217—00787) Apr—08 Reference 30 dB Attenuator SN: S5129 (306) 8—Aug—07 (No, 217—00720) Aug—08 Reference Probe ES3DV2 SN: 3013 2—Jan—08 (No. ES3—3013_Jan08) Jan—09 DAE4 SN: 660 3—Sep—07 (No. DAE4—660_SepO7) Sep—08 Secondary Standards 1D # Check Date (in house) Scheduled Check RF generator HP 8648C US3642U01700 4—Aug—99 (in house check Oct—07) In house check: Oct—09 Network Analyzer HP 8753E US37390585 18—0ct—01 (in house check Oct—07) In house check: Oct—08 Name Calibrated by: Approved by: Issued: June 25, 2008 This callbration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: ES3—3078_JunO8 Page 1 of 9

. . w1 4n Calibration Laboratory of \\\“\\\\\_J/\_;/”/, Schweizerischer Kalibrierdienst Schmid & Partner S‘m Service suisse d‘étalonnage Engineering AG P rrs Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland *4ifi\‘v Swiss Calibration Service *dules® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of callbration certificates Glossary: TSL tissue simulating liquid NORMx,y,z sensitivity in free space ConvF sensitivity in TSL / NORMx,y,z DCP diode compression point Polarization q q rotation around probe axis Polarization 8 8 rotation around an axis that is in the plane normal to probe axis (at measurement center), i.e., 8 = 0 is normal to probe axis Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2003, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", December 2003 b) 1EC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz)", February 2005 Methods Applied and Interpretation of Parameters: e NORMx,y,z: Assessed for E—field polarization 8 = 0 (f < 900 MHz in TEM—cell; f > 1800 MHz: R22 waveguide). NORMx,y,z are only intermediate values, i.e., the uncertainties of NORMx,y,z does not effect the E®—field uncertainty inside TSL (see below ConvF). e NORM(PMx,y,z = NORMx,y,z * frequency_response (see Frequency Response Chart). This linearization is implemented in DASY4 software versions later than 4.2. The uncertainty of the frequency response is included in the stated uncertainty of ConvF. e DCPx,y,z: DCP are numerical linearization parameters assessed based on the data of power sweep (no uncertainty required). DCP does not depend on frequency nor media. e ConvF and Boundary Effect Parameters: Assessed in flat phantom using E—field (or Temperature Transfer Standard for f < 800 MHz) and inside waveguide using analytical field distributions based on power measurements for f > 800 MHz. The same setups are used for assessment of the parameters applied for boundary compensation (alpha, depth) of which typical uncertainty values are given. These parameters are used in DASY4 software to improve probe accuracy close to the boundary. The sensitivity in TSL corresponds to NORMx,y,z * ConvF whereby the uncertainty corresponds to that given for ConvF. A frequency dependent ConvF is used in DASY version 4.4 and higher which allows extending the validity from + 50 MHz to £ 100 MHz. e Spherical isotropy (3D deviation from isotropy): in a field of low gradients realized using a flat phantom exposed by a patch antenna. e Sensor Offset: The sensor offset corresponds to the offset of virtual measurement center from the probe tip (on probe axis). No tolerance required. Certificate No: ES3—3078_JunO8 Page 2 of 9

ES3DV3 SN:3078 June 23, 2008 Probe ES3DV3 SN:3078 Manufactured: March 14, 2005 Last calibrated: July 16, 2007 Recalibrated: June 23, 2008 Calibrated for DASY Systems (Note: non—compatible with DASY2 system!) Certificate No: ES3—3078_JunO8 Page 3 of 9

ES3DV3 SN:3078 June 23, 2008 DASY — Parameters of Probe: ES3DV3 SN:3078 Sensitivity in Free SpaceA Diode CompressionB NormxX 1.26 £101% pV/(V/im) eP x 91 mV NormY 1.27 £10.1% uV/(V/im) DCP Y 95 mV NormZ 1.20 £10.1% uV/(V/im) DCP Z 94 mV Sensitivity in Tissue Simulating Liquid (Conversion Factors) Please see Page 8. Boundary Effect TSL 835 MHz Typical SAR gradient: 5 % per mm Sensor Center to Phantom Surface Distance 3.0 mm 4.0 mm SARpe Dol Without Correction Algorithm 9.4 5.7 SARq [%] With Correction Algorithm 0.7 0.2 TSL 1900 MHz Typical SAR gradient: 10 % per mm Sensor Center to Phantom Surface Distance 3.0 mm 4.0 mm SARpe [%] Without Correction Algorithm 74 4.5 SARp, (%] With Correction Algorithm 0.5 0.1 Sensor Offset Probe Tip to Sensor Center 2.0 mm The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. * The uncertainties of NormX,Y,Z do not affect the E*—field uncertainty inside TSL (see Page 8). ® Numerical linearization parameter: uncertainty not required. Certificate No: ES3—3078_JunO8 Page 4 of 9

ES3DV3 SN:3078 June 23, 2008 Frequency Response of E—Field {TEM—Cell:ifi110 EXX, Waveguide: R22) og in goos b B Frequency response (normalized) ho d > e s p ~ & e o L1 & to & in 500 1000 1500 2000 2500 3000 o f [MHz] [ —@—TEM —o—R22 ] Uncertainty of Frequency Response of E—field: % 6.3% (k=2) Certificate No: ES3—3078_Jun08 Page 5 of 9

ES3DV3 SN:3078 June 23, 2008 Receiving Pattern (¢), 8 = 0° f= 600 MHz, TEM ifff10EXX f= 1800 MHz, WG R22 180 —@—X —@—Y¥ —@—Z —O—Tot —@—X —8—¥ —@—Z —O—Tot 1.0 0.8 0.6 [—0—30MHz —| 0.4 —B— 100 MHz ‘ i Error [dB] 0.2 —0—600 MHz | | 0.0 —2— 1800 MHz | | —0.2 —0.4 —0.6 —0.8 ~1.0 0 so 120 180 240 300 61 Uncertainty of Axial Isotropy Assessment: £ 0.5% (k=2) Certificate No: ES3—3078_Jun08 Page 6 of 9

ES3DV3 SN:3078 June 23, 2008 Dynamic Range f(SARpeaq) (Waveguide R22, f = 1800 MHz) 1.E+06 1.E+05 1.E+04 Input Signal [uV] 1.E+03 1.E+02 1.E+01 1.E+00 0.0001 0.001 0.01 0. 10 100 SAR [mW/cm*] —®— not compensated —&— compensated 1.0 Error [dB] 6o ho ho —0.6 ~1.0 0.001 0.01 0.1 1 10 100 SAR [mWicm‘] Uncertainty of Linearity Assessment: + 0.6% (k=2) Certificate No: ES3—3078_JunO8 Page 7 of 9

ES3DV3 SN:3078 June 23, 2008 Conversion Factor Assessment f= 835 MHz, WGLS R9 (head) f= 1900 MHz, WGLS R22 (head) 4.0 30.0 35 C 25.0 ‘2 8.0 — E 25 A E 20.0 +— 5 s | D 69 5 "J 42 3 20 B 15.0 Jt@l—(i j E15 £ & C 0 & 10.0 w 1.0 a os ( 5.0 | 1 bood. 0.0 & i | —I 0.0 0 20 40 60 0 10 20 30 40 z[mm] z[mm] —©— Analytical —0—Measurements ! i—?):An;lytical —o—Measureme;lg f [MHz] Validity [MHz]® TSL Permittivity Conductivity Alpha Depth ConvF Uncertainty 835 + 50 /# 100 Head 41.5+5% 0.9015% 0.20 2.39 5.90 £11.0% (k=2) 1900 £50/£100 Head 40.0%5% 1.40+5% 0.85 113 4.97 £11.0% (k=2) 2450 £50/+100 Head 39.2+5% 1.80£5% 0.94 114 446 £11.0% (k=2) 835 + 50 /# 100 Body 55.2+5% 0.97%5% 0.33 1.85 5.86 #11.0% (k=2) 1900 £50/%100 Body 53.3%5% 1.52%5% 0.79 1.33 4.58 £11.0% (k=2) 2450 £50/%100 Body 52.7%5% 1.95%#5% 0.96 1.12 4.20 £11.0% (k=2) © The validity of :t 100 MHz only applies for DASY v4.4 and higher (see Page 2). The uncertainty is the RSS of the ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band. Certificate No: ES3—3078_JunO8 Page 8 of 9

ES3DV3 SN:3078 June 23, 2008 Deviation from Isotropy in HSL Error (¢, 8), f = 900 MHz 1.0 ~0.8 0.6 04 0.2 Error [dB] 45 o0 —0.2 90 —0.4 —0.6 180 —0.8 —1.0 $ 225 so 50 270 40 83 30 20 10 o ]-1 .00—0.80 ©1—0,80—0.60 ©—0,60—0.40 ©—0.40—0.20 ©1—0,20—0.00 ©0,00—0,20 ©0,20—0.40 ©0.40—0.60 ©0.60—0.80 ©0.80—1.00 | Uncertainty of Spherical Isotropy Assessment: £ 2.6% (k=2) Certificate No: ES3—3078_JunO8 Page 9 of 9


Document Created: 2008-12-23 10:35:01
Document Modified: 2008-12-23 10:35:01
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC