HAC RF report

FCC ID: V65S1360

Test Report

Download: PDF
FCCID_2006311

Applicant: Kyocera FCC ID: V65S1360 Report #: CT- S1360_20RF-0513-R0 Hearing Aid Compatibility (HAC) RF Emissions FCC 47 CFR Part 20.19 Test Report For Kyocera Corporation c/o Kyocera Communications, Inc. Product: Single-Band CDMA Phone Model: S1360 © 2013 Comptest Services LLC Page 1 of 22 HAC RF Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT- S1360_20RF-0513-R0 TABLE OF CONTENTS 1 SUMMARY OF TESTING ................................................................................................................. 4 2 EQUIPMENT UNDER TEST INFORMATION ................................................................................... 4 3 TEST CONDITIONS ......................................................................................................................... 5 3.1 AMBIENT CONDITIONS ................................................................................................................. 5 3.2 RF CHARACTERISTICS OF THE TEST SITE ...................................................................................... 5 3.3 TEST SIGNAL, FREQUENCIES AND OUTPUT POWER ....................................................................... 5 3.4 EUT OPERATING CONDITIONS ..................................................................................................... 6 4 DESCRIPTION OF TEST EQUIPMENT ........................................................................................... 7 4.1 TEST EQUIPMENT USED .............................................................................................................. 7 4.2 NEAR FIELD MEASUREMENT SYSTEM ........................................................................................... 7 4.3 ISOTROPIC E-FIELD PROBE ......................................................................................................... 8 4.4 ISOTROPIC -FIELD PROBE ............................................................................................................ 8 5 SYSTEM VALIDATION .................................................................................................................... 9 5.1 DIPOLE VALIDATION SETUP ......................................................................................................... 9 5.2 DIPOLE VALIDATION RESULTS .................................................................................................... 10 6 DESCRIPTION OF TEST PROCEDURE ........................................................................................ 11 6.1 TEST POSITIONS ....................................................................................................................... 11 6.2 RF EMISSION MEASUREMENTS REFERENCE AND PLANE ............................................................. 11 6.3 RF EMISSIONS MEASUREMENT PROCEDURES ............................................................................ 12 7 PROBE MODULATION FACTOR (PMF)........................................................................................ 13 7.1 PMF MEASUREMENT PROCEDURES ........................................................................................... 13 7.2 PMF TEST RESULTS ................................................................................................................. 14 7.3 PMF PEAK POWER MEASUREMENT PLOTS ................................................................................. 15 8 EMISSION DATA EXTRACTION AND POSTPROCESSING ......................................................... 17 9 MEASUREMENT UNCERTAINTY.................................................................................................. 18 10 RF EMISSIONS TESTS .................................................................................................................. 19 10.1 EMISSION LIMITS ....................................................................................................................... 19 10.2 CDMA 1900 TEST RESULTS...................................................................................................... 20 10.3 WORST-CASE CONFIGURATION EVALUATION .............................................................................. 21 11 APPENDIX A: PROBE CALIBRATION CERTIFICATION .............................................................. 22 12 APPENDIX B: SYSTEM VALIDATION DATA PLOTS ................................................................... 22 13 APPENDIX C: TEST RESULTS/PLOTS ........................................................................................ 22 14 APPENDIX D: PHOTO TEST SETUP ............................................................................................ 22 © 2013 Comptest Services LLC Page 2 of 22 HAC RF Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT- S1360_20RF-0513-R0 ATTESTATION The tested device complies with the requirements in respect of all parameters subject to the test. The test results and statements relate only to the items tested. The test equipment used was suitable for the tests performed and within manufacturer’s published specifications and operating parameters. The test methods were consistent with the methods described in the relevant standards. Product: CDMA Cellular Phone with Bluetooth Model #: S1360 FCC ID: V65S1360 Tested in accordance with: FCC 47 CFR Part 20.19 ANSI C63.19-2007 Test performed by: Comptest Services LLC Test Requested by: KYOCERA Corporation C/o KYOCERA Communications, Inc. 8611 Balboa Ave. San Diego, CA 92123 United States Date of Test: May 2, 2013 Responsible Engineer Reviewed and approved by: Benjamin Nguyen Kelly Hill Benjamin Nguyen Kelly Hill Test Engineer Quality Manager © 2013 Comptest Services LLC Page 3 of 22 HAC RF Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT- S1360_20RF-0513-R0 1 SUMMARY OF TESTING Rule Part Test Description Section # Verdict FCC § 20.19(b), §6.3(v), §7.3(v) HAC RF Emissions 4 Pass ANSI C63.19-2007 HAC M Category: M4 2 EQUIPMENT UNDER TEST INFORMATION Product: CDMA Cellular Phone with Bluetooth FCC ID: V65S1360 Model Number: S1360 EUT Serial Number: 268435457816732379 Type: [ ] Identical Prototype, [X] Pre-Production, [ ] Production Device Category: Portable RF Exposure General Population / Uncontrolled Environment: Antenna: Internal Detachable Antenna: Yes External Input: Audio/Digital Data Quantity: Quantity production is planned Mode: CDMA 1x Band: BC-1 TX Frequency (MHz): 1850 -1910 © 2013 Comptest Services LLC Page 4 of 22 HAC RF Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT- S1360_20RF-0513-R0 3 TEST CONDITIONS 3.1 Ambient Conditions All tests were performed under the following environmental conditions: Ambient Temperature: 23 ± 2 Degrees C Tissue simulating liquid temperature: 22 ± 1 Degrees C Relative Humidity (RH): 0% <RH < 80% Atmospheric Pressure: 101.3kPa + 10 to –5 kPa 3.2 RF characteristics of the test site All HAC measurements were performed inside a shielded room that provide isolation from external EM fields, with the RF ambient at least 20 dB below the intended measurement limits. 3.3 Test Signal, Frequencies and Output Power The device supports CDMA2000 in 1X (Phase I, Protocol revision 6) mode only. CDMA2000 1X includes TIA/EIA-95B as a subset and was approved for publishing in July 1999. It provides voice and data capabilities within a standard 1.25 MHz CDMA channel. This RF bandwidth is identical to the legacy IS-95 B system standard. Peak and Average conducted power were measured to ensure worst case power configuration was tested: CONFIGURATION CONDUCTED POWER (Full Rate) CDMA 1900 (ch 600) Average (dBm) SO2 RC1 24.74 RC3 24.73 SO55 RC1 24.75 RC3 24.78 SO32 RC3 (+SCH) 24.77 RC3 (+F-SCH) 24.74 In all operating modes, the phone was set to rated maximum RF power level and the measurements were performed on low, mid and high channels. The measurement system measures power drift during HAC testing by comparing E/H-field in the same location at the beginning and at the end of measurement. These records were used to monitor stability of power output during tests. Conducted RF power measurements were also performed before and after each HAC measurements to confirm the output power. © 2013 Comptest Services LLC Page 5 of 22 HAC RF Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT- S1360_20RF-0513-R0 During tests, the EUT was put in in-call mode and controlled by a CDMA simulator to generate the required signal and power: Protocol: 6 (IS-2000) Radio Configuration: 3 Power Control: All Up Bits Service Option: 55 Data Rate: Full 3.4 EUT Operating Conditions The EUT was tested with the follow configurations and conditions, if applicable: Voice Over IP Simultaneous Band C63.19 Mode Type Transport Transmissions (MHz) (Tested) (Data) (Not Tested) CDMA 1x 1900 Voice N/A Yes: BT Yes CDMA EVDO Rev0, A Bluetooth 2450 Data N/A Yes: CDMA N/A WiFi X Fully charged standard battery as supplied with the handset Closed configurations at ear use position 1 Both retracted and extended antenna positions X Back-light always ON Reduce Power Note: 1: This device has only one configuration for ear usage © 2013 Comptest Services LLC Page 6 of 22 HAC RF Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT- S1360_20RF-0513-R0 4 DESCRIPTION OF TEST EQUIPMENT 4.1 Test Equipment Used Below is a list of the calibrated equipment used for the measurements. The calibration certificates of E-field and H-field probes are attached in Appendix A. Description Manufacturer Model Serial Number Cal Due Date Number Power Meter Giga-tronics 8541C 1831306 05/16/13 Signal Generator Hewlett Packard E4421B US38440337 06/28/13 Radio Communication Tester Agilent 8960 GB44052789 12/02/13 Data Acquisition Speag DAE4 527 07/30/13 E-field Probe Speag ER3DV6 2341 09/14/13 H-field Probe Speag H3DV5 6029 09/14/13 Dipole Antenna (835MHz) Speag CD835V3 1020 03/08/13 Dipole Antenna (1880MHz) Speag CD1880V3 1015 03/08/13 Note: Dipoles are calibrated on a 2-year interval. Dipoles return-loss and input impedances are measured annually (50824 DO2 Dipole SAR Validation Verification v01). 4.2 Near Field Measurement System The measurements were performed with Dasy4 automated near-field scanning system comprised of high precision robot, robot controller, computer, near-field probe, probe alignment sensor, non- conductive phone positioner, Test Arch and software extension. The overall expanded uncertainty (K=2) of the measurement system is 10.9% and 14.7% for H-field and E-field resp. The measurement uncertainty budget is given in section 6. © 2013 Comptest Services LLC Page 7 of 22 HAC RF Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT- S1360_20RF-0513-R0 4.3 Isotropic E-Field Probe Model  ER3DV6 Construction  One dipole parallel, two dipoles normal to probe axis  Built-in shielding against static charges  PEEK enclosure material (resistant to organic solvents, e.g., glycolether) Calibration  In air from 100 MHz to 3.0 GHz (absolute accuracy ± 6%; k=2) Frequency  100MHz to 6 GHz  Linearity: ± 0.2dB (100MHz to 3GHz) Directivity  ± 0.2 dB in air (rotation around probe axis)  ± 0.4 dB in air (rotation normal to probe axis) Dynamic Range  2 V/m to > 1000 V/m  Linearity: ± 0.2 dB Dimensions  Overall length: 330 mm (Tip: 16 mm)  Tip diameter: 8 mm (Body: 12 mm)  Distance from probe tip to dipole centers: 2.5 mm Application  General near-field measurements up to 6 GHz  Field component measurements  Fast automatic scanning in phantoms 4.4 Isotropic -Field Probe Model  H3DV6 Construction  Three concentric loop sensors with 3.8 mm loop diameters  Resistively loaded detector diodes for linear response  Built-in shielding against static charges  PEEK enclosure material (resistant to organic solvents, e.g., glycolether) Frequency  200 MHz to 3 GHz (± 6.0%, k=2); Output linearized Directivity  ± 0.25 dB (spherical isotropy error) Dynamic Range  10 mA/m to 2 A/m at 1 GHz E-Field Interference  < 10% at 3 GHz (for plane wave) Dimensions  Overall length: 330 mm (Tip: 40 mm)  Tip diameter: 6 mm (Body: 12 mm)  Distance from probe tip to dipole centers: 3 mm Application  General magnetic near-field measurements up to 3 GHz  Field component measurements  Surface current measurements  Measurements in air or liquids  Low interaction with the measured field © 2013 Comptest Services LLC Page 8 of 22 HAC RF Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT- S1360_20RF-0513-R0 5 SYSTEM VALIDATION 5.1 Dipole Validation Setup The probes are calibrated annually by the manufacturer. The HAC measurements of the device were done within 24 hours of system accuracy verification, which was done using calibration dipoles. Unmodulated continous wave of power level of 20dBm was supplied to a dipole antenna placed under Test Arch. The measurement probes are positioned over the illuminated dipole at 10mm distance from the top surface of the dipole element to the calibration reference point of the sensor, defined by the probe manufacturer. Figure 5 System Check Setup © 2013 Comptest Services LLC Page 9 of 22 HAC RF Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT- S1360_20RF-0513-R0 5.2 Dipole Validation Results The length of the dipole was scanned with both E and H-field probes and the maximum values for each were recorded. The validation results are in the table below and printouts of the validation test are attached in Appendix B. All the measured parameters were within the specification. Freq. (MHz) Parameter Target Measured Delta (%) Limit (%) Test date (SPEAG) E dB(V/m) 142.0 136.9 -3.59  25 05/02/13 1880 H dB(A/m) 0.473 0.470 -0.85  25 05/02/13 © 2013 Comptest Services LLC Page 10 of 22 HAC RF Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT- S1360_20RF-0513-R0 6 DESCRIPTION OF TEST PROCEDURE 6.1 Test Positions The device was placed on a non-conductive phone positioner under the Test Arch. 6.2 RF Emission Measurements Reference and Plane Figure 6.2 illustrates the references and reference plane that shall be used in the EUT emissions measurement:  The grid is 5 cm by 5 cm area that is divided into 9 evenly sized blocks or sub-grids.  The grid is centered on the audio frequency output transducer (speaker) of the EUT.  The grid is in a reference plane, which is defined as the planar area that contains the highest point in the area of the phone that normally rests against the user's ear. It is parallel to the centerline of the receiver of the EUT and is defined by the points of the receiver-end of the EUT, which, in normal handset use, rest against the ear.  The measurement plane is parallel to, and 1.5 cm in front of, the reference plane. Vertical centerline of phone 5 x 5 cm grid Horizontal centerline of acoustic output Measurement plane 1.5 cm Reference plane Figure 6.2 – Measurement Reference and Plane © 2013 Comptest Services LLC Page 11 of 22 HAC RF Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT- S1360_20RF-0513-R0 6.3 RF Emissions Measurement Procedures Flowchart below shows the near field emission measurement: 1. The center of the probe was scan to the edges of the grid. Accordingly the total area covered by the outside edge of the probe was the 5 cm by 5 cm area, increased by half (½) the probe diameter on all sides. 2. The nearest point on the probe measurement element(s) was held 1.0 cm from the EUT reference plane. 3. The probe element is that portion of the probe that is designed to receive and sense the field being measured. 4. The physical body of the probe housing was not used when setting this 1.0 cm distance as this would place the sensing elements at an indeterminate distance from the reference plane. 5. The step size of the scan is set to 5 mm or less. 6. Up to three blocks were excluded for each field measurement.  The center block containing the EUT output was not excluded.  A maximum of five blocks were excluded for both E- and H-field measurements for the EUT output being measured. Stated differently, the center sub-grid or block and 3 other blocks were common to both the E- and H-field measurements for a given grid.  Confirm proper operation of probes and instrumentation  Position EUT in test position  Configure EUT TX Operation  Initialize field probe and take first reading  Scan Area  Measure Drift  Identify exclusion area and then identify and  Rescan for E or H-Field as record maximum reading in V/m or A/m needed All Configurations and Both E & H Field Scanned? Yes  Identify and record Category Figure 7.6 Near field emission measurement flowchart © 2013 Comptest Services LLC Page 12 of 22 HAC RF Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT- S1360_20RF-0513-R0 7 PROBE MODULATION FACTOR (PMF) 7.1 PMF Measurement Procedures A calibration was made of the modulation response of the probe and its instrumentation chain. This calibration was performed with the field probe, attached to its instrumentation. The response of the probe system to a CW field at the frequency of interest is compared to its response to a modulated signal with equal peak amplitude to that of a CW signal. The field level of the test signals shall be more than 10 dB above the ambient level and the noise floor of the instrumentation being used. The ratio of the CW reading to that taken with a modulated reading was applied to the DUT measurements. The measurement procedures are as following: 1. Fix the field probe in a set location relative to the dipole antenna, as illustrated in Figure 7.4. 2. Setup the wireless device (EUT) with intended signal at the intended measurement frequency.\ 3. Record the reading of the probe measurement system. 4. Replace the wireless device with a RF signal generator producing an unmodulated CW signal and set to the wireless device operating frequency. 5. Set the peak power of the unmodulated signal to equal that recorded from the wireless device 6. Record the reading of the probe measurement system of the unmodulated CW signal. 7. The ratio of probe reading (CW) in step 6 to the probe reading (EUT) in step 3 is the modulation factor. Figure 7.4 © 2013 Comptest Services LLC Page 13 of 22 HAC RF Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT- S1360_20RF-0513-R0 7.2 PMF Test Results The modulation factors obtained by above method shall be applied to readings taken of the actual WD, in order to obtain an accurate peak field reading. E-Field Frequency Peak Power Protocol Protocol Reading Modulation Factor (MHz) (dBm) (V/m) 835 24.32 CW 127.6 24.32 CDMA (full rate) 127.4 1.00 24.32 AM 77.77 1.64 1880 22.92 CW 69.51 22.92 CDMA (full rate) 70.66 0.98 22.92 AM 44.42 1.56 H-Field Frequency Peak Power Protocol Protocol Reading Modulation Factor (MHz) (dBm) (A/m) 835 24.50 CW 0.343 24.50 CDMA (full rate) 0.335 1.02 24.61 AM 0.223 1.54 1880 22.92 CW 0.272 22.94 CDMA (full rate) 0.277 0.98 22.92 AM 0.173 1.57 © 2013 Comptest Services LLC Page 14 of 22 HAC RF Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT- S1360_20RF-0513-R0 7.3 PMF Peak Power Measurement Plots CDMA-800 CW 80% AM © 2013 Comptest Services LLC Page 15 of 22 HAC RF Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT- S1360_20RF-0513-R0 CDMA-1880 CW 80% AM © 2013 Comptest Services LLC Page 16 of 22 HAC RF Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT- S1360_20RF-0513-R0 8 EMISSION DATA EXTRACTION AND POSTPROCESSING At the end of the measurements, the DASY4 system automatically evaluates the slot-averaged results, exclusion of the three highest subgrid, application of the AWF factor per ANSI-C63.19 requirements. The following AWF factors were used for the standard transmission protocols: Standard Technology AWF TIA/EIA/IS-2000 CDMA 0 TIA/EIA-136 TDMA (50 Hz) 0 J-STD-007 GSM (217) -5 T1/T1P1/3GPP UMTS (WCDMA) 0 TM iDEN TDMA(22 and 11 Hz) 0 Table 8.1 Articulation Weighting Factor (AWF) All DASY4 measurements are in RMS values. The Dasy4 system incorporates the crest factor of the signal in the computation of the RMS values. Although the software also has the capability to estimate the peak field by applying a square root of the crest factor value to the readings, the probe modulation factor was applied manually instead per ANSI C63.19 in the measurement tables in this report using equation: Peak Field = (DASY4 reading) x PMF where DASY4 reading = measurement from DASY4 in V/m or A/m PMF = Probe Modulation Factor in linear unit © 2013 Comptest Services LLC Page 17 of 22 HAC RF Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT- S1360_20RF-0513-R0 9 MEASUREMENT UNCERTAINTY Table 8.1 shows the uncertainty budget for HAC free field assessment according to ANSI C63.19- 2007. The budget is valid for the frequency range 800 MHz - 3 GHz and represents a worst-case analysis. For specific tests and configurations, the uncertainty could be smaller. Uncertainty Description Uncert Prob Div. Ci Ci Stand. Stand. . Value . (E) (H) Uncert (E) Uncert (H) ( %) Dist. (%) (%) Measurement system Probe calibration 5.1 N 1 1 1 5.1 5.1 Axial isotropy of the probe 4.7 R √3 1 1 2.7 2.7 Sensor displacement 16.5 R √3 1 0.14 9.5 1.4 5 Boundary effects 2.4 R √3 1 1 1.4 1.4 Probe linearity 4.7 R √3 1 1 2.7 2.7 Scaling to Peak Envelope 2.0 R √3 1 1 1.2 1.2 Power System Detection limit 1.0 R √3 1 1 0.6 0.6 Readout electronics 0.3 N 1 1 1 0.3 0.3 Response time 0.8 R √3 1 1 0.5 0.5 Integration time 2.6 R √3 1 1 1.5 1.5 RF ambient conditions 3.0 R √3 1 1 1.7 1.7 RF Reflections 12 R √3 1 1 6.9 6.9 Probe Positioner 1.2 R √3 1 0.67 0.7 0.5 Probe positioning 4.7 R √3 1 0.67 2.7 1.8 Extrap. and integration 1.0 R √3 1 1 0.6 0.6 Test Sample Related Device positioning vertical 4.7 R √3 1 0.67 2.7 1.8 Device Positioning Lateral 1.0 R √3 1 1 0.6 0.6 Device Holder and Phantom 2.4 R √3 1 1 1.4 1.4 Power drift 5.0 R √3 1 1 2.9 2.9 Phantom and Setup Related Phantom thickness 2.4 R √3 1 0.67 1.4 0.9 Combined Standard Uncertainty: 14.7 10.9 Extended Standard Uncertainty on Power (k=2): 29.4 21.8 Extended Standard Uncertainty on Field (k=2): 14.7 10.9 N: Normal R: Rectangular Table 9.1 Worst-Case uncertainty budget for HAC free field assessment © 2013 Comptest Services LLC Page 18 of 22 HAC RF Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT- S1360_20RF-0513-R0 10 RF EMISSIONS TESTS 10.1 Emission Limits FCC: § 20.19, ANSI C63.19-2007 IC: Table 10.1 shows the M-rating criteria from ANSCI C63.19. All digital transmission modes in all frequency bands contained in a HAC phone must meet M3 or M4 levels. Near Wireless Device RF Parameters Field [AWF = 0] E-Field Emissions H-Field Emissions Category dB(V/m) Peak V/m Peak dB(A/m) Peak A/m Peak Freq < 960 MHz M1 56.0 to 61.0 631.0 to 1122.0 5.6 to 10.6 1.91 to 3.39 M2 51.0 to 56.0 354.8 to 631.0 0.6 to 5.6 1.07 to 1.91 M3 46.0 to 51.0 199.5 to 354.8 -4.4 to 0.6 0.60 to 1.07 M4 < 46.0 < 199.5 < -4.4 < 0.60 Freq > 960 MHz M1 46.0 to 51.0 199.5 to 354.8 -4.4 to 0.6 0.60 to 1.07 M2 41.0 to 46.0 112.2 to 199.5 -9.4 to -4.4 0.34 to 0.60 M3 36.0 to 41.0 63.1 to 112.2 -14.4 to -9.4 0.19 to 0.34 M4 < 36.0 < 63.1 < -14.4 < 0.19 Table 10.1 RF Emission Limits © 2013 Comptest Services LLC Page 19 of 22 HAC RF Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT- S1360_20RF-0513-R0 10.2 CDMA 1900 Test Results Configuration: Bar Antenna: Fixed CDMA 1900 E-Field Ch. Backlight Power Dasy4 PMF Peak Field Category Reading # dBm V/m V/m M 25 ON 24.72 42.16 1.00 42.16 4 600 ON 24.78 32.86 1.00 32.86 4 1175 ON 24.76 32.80 1.00 32.80 4 CDMA 1900 H-Field Ch. Backlight Power Dasy4 PMF Peak Field Category Reading # dBm A/m A/m M 25 ON 24.72 0.11 1.00 0.11 4 600 ON 24.78 0.11 1.00 0.11 4 1175 ON 24.76 0.11 1.00 0.11 4 © 2013 Comptest Services LLC Page 20 of 22 HAC RF Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT- S1360_20RF-0513-R0 10.3 Worst-Case Configuration Evaluation The probe was rotated 360o at Azimuth axis in the worst case configuration. The rotation was performed at the location of maximum field strength in the included blocks. CDMA 1900 E-Field Configuration: Bar Antenna: Fixed Ch. Backlight Conducted Peak Field PMF Peak Field Category Power # dBm V/m V/m M 25 ON 24.72 42.16 1.00 42.16 4 Data plots are shown in Appendix C © 2013 Comptest Services LLC Page 21 of 22 HAC RF Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT- S1360_20RF-0513-R0 11 APPENDIX A: PROBE CALIBRATION CERTIFICATION (See attachment) 12 APPENDIX B: SYSTEM VALIDATION DATA PLOTS (See attachment) 13 APPENDIX C: TEST RESULTS/PLOTS (See attachment) 14 APPENDIX D: PHOTO TEST SETUP (See attachment) © 2013 Comptest Services LLC Page 22 of 22 HAC RF Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.


Document Created: 2013-05-15 14:39:58
Document Modified: 2013-05-15 14:39:58
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC