User manual

FCC ID: V5PS900

Users Manual

Download: PDF
FCCID_2656654

S900 Mobile Payment Terminal PAX TECHNOLOGY LIMITED

1. Product Description: Magnetic Strip Card Siot Function Key Keypad 1G Card Slot Cutter Printer Cover Handle Printer Cover Rubber Pad Nameplate Barcode Label Baltery Battery Power Charge Port SIM Card Slot SAM Card Slot so

2. Installation 1） SAM Card Installation ① Open up battery cover, which is at the bottom of the terminal; ② Take out battery; ③ Insert SAM card to corresponding SAM card slot. 2） SIM Card Installation ① Open up battery cover, which is at the bottom of the terminal ② Take out battery; ③ Insert SIM card to corresponding SIM card slot. 3） SD Card Installation ① Open up battery cover, which is at the bottom of the terminal; ② Take out battery; ③ Insert SD card to corresponding SD card slot. 4） Battery Installation ① Hold the battery with its sticker facing up; ② Attach battery forelock to battery bayonet; ③ Press down the other side of the battery 3. Instruction 1） Power ON/OFF Power on: Press “CANCEL” button for 2 seconds until LED backlight is on, if POS terminal is being turned on successfully. Power off: Press “CANCEL” button for 2 seconds until the displaying content vanishes. POS terminal is being turned off. 2） Magnetic Stripe Card When user swipes magnetic stripe card along the slot, the backside of the card, which contains magnetic stripe information, should be facing to the terminal. Bi-directional swiping is supported. It is recommended to swipe starting from the top of the terminal to the bottom of the terminal with a constant moving speed. 3） IC card When user inserts IC card into the IC slot, the chip of IC card should be facing up; user is recommended to gently insert the card, in order to avoid any physical damage to the card or the IC slot of the terminal. If IC card is successfully read by the terminal, the IC card icon will be shown on LCD display screen. ICC Operation Process Before inserting the IC card, please check inside and around the IC card slot. If there is any suspicious object, please don‘t insert card and immediately report to the relevant staff. 4） Tearing off receipt from the terminal After the receipt is printed, pinch the end of the receipt and keep an angle of 45 degrees between receipt and the cutter of the terminal; tear off the receipt swiftly. 4. Specifications Default CPU： 32-bit，ARM11 Memory：64MB DDR RAM , 128MB NAND Flash

Displiye 315 inch 2401320 prel colorTRT LCD: LED beckight ‘Touch Sereens support Elecroni signstire Keypad:. 10 abhanumerks heys.8 furctional keys Magnetic Card Reader c Trock V2R. direcionalswipe 1C CardReaders 1 usercard. CEMY2000) SAM shis: 1) SIMsbtX 1 + SAM sbtxcwihout 3D sby 2)| Sintsh X 2+ 8AM slot X2 wihouSD sho 3)| SiMshc X 1+ SAM sht X2+ DsbX 1 4). SAM slot 30ME , witout Dsl 5): SAM stXG+5DsbiX. 1fi Communication GSM, GPRS, or WCDMA or WiF—2T PeriheralPorts: 1 RS232por 1088 port 1 Power Chargeport Priver "Thermalrinter; Speec:18 nes/secPaper wiithSBmm PaperrolloutstedameterBrom Pover Supply« Inpuls 100—204C . 10A 5oboHz Ouipue $.0V DC2.5A Baterys Len biten1850mANTV Working Envronments Temperstire: 0 ‘C=50°CE2F—1227) RH: 10%—93%fnon—condense) Storige Envronments Tempersire=20© ~10C. (4°F—Is07) RH:3% 95%(non—condense) Dimensions. 1?Smm. X82mm6mm (LXWxHD Weights 386 Optionat SupportSD card Biltcin WiPkBT. modile (ro GSM,GPRS or NCDMA) Double SIMshis Pn contctiss card reader modile (190/220 14009 Type 4/B, Itare® Aretsca/iee, card sensing areat LCD screen) 1D2D barcodeseanrer 5.Installtion andUsage Tips 1}Do not damage elcirc wire and power adaple1f lcirc wire or power adaptei damaged . please do not use the terminalany more 2) Before pover adapler is plugged nto pooer socket,pese make sure that volage which the power socket supples s approprste working valage forthterminal 3)Do not exposethe terminalin sunshine,o in huril, hot,ordusty environment 4)Keep theterminal avay from lt material 5) Do not plig any unknown matera nto any port of the ermina, since it may cresteserus damage t the terminal

6) If the terminal is defective, please contact professional POS repair technicians. 7) When installing paper roll, please be aware of the cutter within paper bracket. 8) Please use standard thermal paper, in order to protect the printer and avoid paper jam. 9) Do not assemble the terminal in explosion hazardous area. 6.Battery Usage Tips 1) Charge indoor by PAX charger, where is cool and well ventilated; 2) Do not apart the battery; 3) Do not short circuit the battery; 4) Keep the battery away from sunshine, smog and dust; 5) Do not squeeze, punch the battery, put it into liquid or near fire; 6) Keep way from environment which is too hot , too cold, damp and highly explosive; 7) Once a failure happens such as heating or distortion, or it was broken down. Please change new battery; 8) Change new battery if it cannot satisfy your requirement; 9) Change new battery if using more than two years. FCC Regulations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. FCC RF Exposure Information (SAR) This device is designed and manufactured not to exceed the emission limits for exposure to

radio frequency (RF) energy set by the Federal Communications Commission of the United States. During SAR testing, this device is set to transmit at its highest certified power level in all tested frequency bands, and placed in positions that simulate RF exposure in usage near the body. Although the SAR is determined at the highest certified power level, the actual SAR level of the while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. The exposure standard for wireless employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. The FCC has granted an Equipment Authorization for this model device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC ID: V5PS900. For this device, the highest reported SAR value for near the body is 1.20W/kg. While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement. IC Notice This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme àla norme NMB-003 du Canada. IC: 11689A-S900

IC Radiation Exposure Statement This EUT is compliance with SAR for general population/uncontrolled exposure limits in IC RSS-102 and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528 and IEC 62209. This device and its antenna(s) must not be co-located oroperating in conjunction with any other antenna or transmitter. Cet appareil est conforme aux limites d'exposition DAS incontrôlée pour la population générale de la norme CNR-102 d'Industrie Canada et a ététestéen conformitéavec les méthodes de mesure et procédures spécifiées dans IEEE 1528 et IEC 62209. Cet appareil et sa ou ses antennes ne doivent pas êtreco-localisés ou fonctionner en conjonction avec tout autre antenne ou transmetteur. P/N：200312000000189


Document Created: 2015-06-17 10:59:52
Document Modified: 2015-06-17 10:59:52
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC