Test report

FCC ID: V5PIM30BW

Test Report

Download: PDF
FCCID_4434518

Shenzhen ZhongjianNanfang Testing Co., Ltd. Report No: CCISE190704306V01 1 Cover Page FCC REPORT Applicant: PAX Technology Limited Address of Applicant: Room 2416, 24/F., Sun Hung Kai Centre, 30 Harbour Road, Wanchai, Hong Kong Equipment Under Test (EUT) Product Name: POS Terminal Model No.: IM30 Trade mark: PAX FCC ID: V5PIM30BW Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.225 Date of sample receipt: 11 Jul., 2019 Date of Test: 11 Jul., to 16 Aug., 2019 Date of report issue: 05 Step., 2019 Test Result: PASS* * In the configuration tested, the EUT complied with the standards specified above. Authorized Signature: Bruce Zhang Laboratory Manager This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product and does not permit the use of theCCISproduct certification mark. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery orfalsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.

Report No: CCISE190704306V01 2 Version Version No. Date Description 00 19 Aug., 2019 Original 01 05 Step., 2019 Update page 11~13 Tested by: Date: 05 Step., 2019 Test Engineer Reviewed by: Date: 05 Step., 2019 Project Engineer Shenzhen ZhongjianNanfang Testing Co., Ltd. Project No.: CCISE1907043 No.B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong,China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 2 of 24

Report No: CCISE190704306V01 3 Contents Page 1 COVER PAGE ....................................................................................................................................................... 1 2 VERSION ............................................................................................................................................................... 2 3 CONTENTS ........................................................................................................................................................... 3 4 TEST SUMMARY .................................................................................................................................................. 4 5 GENERAL INFORMATION .................................................................................................................................. 5 5.1 CLIENT INFORMATION ............................................................................................................................................ 5 5.2 GENERAL DESCRIPTION OF E.U.T........................................................................................................................ 5 5.3 TEST MODE ............................................................................................................................................................ 6 5.4 MEASUREMENT UNCERTAINTY.............................................................................................................................. 6 5.5 DESCRIPTION OF SUPPORT UNITS ........................................................................................................................ 6 5.6 LABORATORY FACILITY.......................................................................................................................................... 6 5.7 LABORATORY LOCATION ....................................................................................................................................... 6 5.8 TEST INSTRUMENTSLIST........................................................................................................................................ 7 6 TEST RESULTS ANDMEASUREMENT DATA ................................................................................................. 8 6.1 ANTENNA REQUIREMENT ....................................................................................................................................... 8 6.2 RADIATED EMISSION ............................................................................................................................................. 9 6.3 20DB BANDWIDTH ............................................................................................................................................... 16 6.4 FREQUENCY TOLERANCE .................................................................................................................................... 18 6.5 CONDUCTED EMISSION ....................................................................................................................................... 20 7 TEST SETUP PHOTOS...................................................................................................................................... 23 8 EUT CONSTRUCTIONAL PHOTOS ................................................................................................................. 24 Shenzhen ZhongjianNanfang Testing Co., Ltd. Project No.: CCISE1907043 No.B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong,China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 3 of 24

Report No: CCISE190704306V01 4 Test Summary Test Item Section in CFR 47 Result Antenna requirement 15.203 Pass Field strength of the fundamental signal 15.225 (a) Pass Spurious emissions 15.225(d)& 15.209 Pass 20dB Bandwidth 15.215(c) Pass Frequency tolerance 15.225 (e) Pass Conducted Emission 15.207 Pass Remarks: Pass: The EUT complies with the essential requirements in the standard. Shenzhen ZhongjianNanfang Testing Co., Ltd. Project No.: CCISE1907043 No.B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong,China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 4 of 24

Report No: CCISE190704306V01 5 General Information 5.1 Client Information Applicant: PAX Technology Limited Address: Room 2416, 24/F., Sun Hung Kai Centre, 30 Harbour Road, Wanchai, Hong Kong Manufacturer/ Factory: PAX Computer Technology(Shenzhen) Co. Ltd. Address: 401-402 No.3 Building, Software Park, Nanshan district, Shenzhen, Guangdong, P.R.C. 5.2 General Description of E.U.T. Product Name: POS Terminal Model No.: IM30 Operation Frequency: 13.56MHz Channel numbers: 1 Modulation type: ASK Antenna Type: Induction Coil Antenna IC Card Type: Support: Type A, Type B, Type M Power supply: DC 12V-48V Test Sample Condition: The test samples were provided in good working order with no visible defects. Shenzhen ZhongjianNanfang Testing Co., Ltd. Project No.: CCISE1907043 No.B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong,China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 5 of 24

c c I s Report No: CCISE190704306V01 5.3 Test mode Transmitting mode: Keep the EUT in transmitting mode with modulation Pre—Test Mode: CCIS has verified the construction and function in typical operation,The EUT was placed on three different polar directions;i.e. X axis, Y axis, Z axis. which was shown in this test report and defined as follows: Axis X Y Z Field Strength(dBuV/m) 59.33 59.95 §8.21 Final Test Mode: According to ANSI C63.4 standards, the test results are both the "worst case" and "worst setup": Y axis (see the test setup photo). 5.4 Measurement Uncertainty Parameters Expanded Uncertainty Conducted Emission (@kHz ~ 30MHz) +1.60 dB (k=2) Radiated Emission (OkHz ~ 3OMHz) +3.12 dB (k=2) Radiated Emission (30MHz ~ 1000MHz) +4.32 dB (k=2) 5.5 Description of Support Units Manufacturer Description Model Serial Number FCC ID/DoC HONOR AC Adapter ADS—65H1—19A—2 24065E N/A N/A 5.6 Laboratory Facility The test facility is recognized, certified, or accredited by the following organizations: ®@ FCC — Designation No.: CN1211 Shenzhen Zhongjian Nanfang Testing Co., Ltd. has been accredited as a testing laboratory by FCC(Federal Communications Commission). The test firm Registration No. is 727551. @ ISED — CAB identifier.: CNOO21 The 3m Semi—anechoic chamber of Shenzhen Zhongjian Nanfang Testing Co., Ltd. has been Registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 10106A—1. @ CNAS — Registration No.: CNAS L6048 Shenzhen Zhongjian Nanfang Testing Co., Ltd. is accredited to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration laboratories for the competence of testing. The Registration No. is CNAS L6048. ® A2LA — Registration No.: 4346.01 This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. The test scope can be found as below link: https //portal. a2la.org/scopepdf/4346—0 1 .pdf 5.7 Laboratory Location Shenzhen Zhongjian Nanfang Testing Co., Ltd. Address: No. B—C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao‘an District, Shenzhen, Guangdong, China Tel: +86—755—23118282, Fax: +86—755—23116366 Email: info@ccis—cb.com, Website: http:/Avww.ccis—cb.com Shenzhen ZhongjianNantang Testing Co., Ltd. Project No.: CCISE1907043 No.B—C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bac‘an District, Shenzhen, Guangdong,China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 6 of 24

Report No: CCISE190704306V01 5.8 Test Instrumentslist Radiated Emission: Cal.Date Cal. Due date Test Equipment Manufacturer Model No. Serial No. (mm-dd-yy) (mm-dd-yy) 3m SAC SAEMC 9m*6m*6m 966 07-22-2017 07-21-2020 BiConiLog Antenna SCHWARZBECK VULB9163 497 03-18-2019 03-17-2020 Biconical Antenna SCHWARZBECK VUBA9117 359 06-22-2017 06-21-2020 Horn Antenna SCHWARZBECK BBHA9120D 916 03-18-2019 03-17-2020 Horn Antenna SCHWARZBECK BBHA9120D 1805 06-22-2017 06-21-2020 Horn Antenna SCHWARZBECK BBHA 9170 BBHA9170582 11-21-2018 11-20-2019 Loop Antenna SCHWARZBECK FMZB 1519 B 00044 03-18-2019 03-17-2020 EMI Test Software AUDIX E3 Version: 6.110919b Pre-amplifier HP 8447D 2944A09358 03-18-2019 03-17-2020 Pre-amplifier CD PAP-1G18 11804 03-18-2019 03-17-2020 Spectrum analyzer Rohde & Schwarz FSP30 101454 03-18-2019 03-17-2020 Spectrum analyzer Rohde & Schwarz FSP40 100363 11-21-2018 11-20-2019 EMI Test Receiver Rohde & Schwarz ESRP7 101070 03-18-2019 03-17-2020 Signal Generator Rohde & Schwarz SMX 835454/016 03-18-2019 03-17-2020 Signal Generator R&S SMR20 1008100050 03-18-2019 03-17-2020 Cable ZDECL Z108-NJ-NJ-81 1608458 03-18-2019 03-17-2020 Cable MICRO-COAX MFR64639 K10742-5 03-18-2019 03-17-2020 Cable SUHNER SUCOFLEX100 58193/4PE 03-18-2019 03-17-2020 Conducted Emission: Cal.Date Cal.Due date Test Equipment Manufacturer Model No. Inventory No. (mm-dd-yy) (mm-dd-yy) Shielding Room ZhongShuo Electron 11.0(L)x4.0(W)x3.0(H) CCIS0061 07-22-2017 07-21-2020 EMI Test Receiver Rohde & Schwarz ESCI CCIS0002 03-18-2019 03-17-2020 LISN CHASE MN2050D CCIS0074 03-18-2019 03-17-2020 07-21-2018 07-20-2021 LISN Rohde & Schwarz ESH3-Z5 8438621/010 07-21-2019 07-20-2020 Coaxial Cable CCIS N/A CCIS0086 03-18-2019 03-17-2020 EMI Test Software AUDIX E3 Version: 6.110919b Shenzhen ZhongjianNanfang Testing Co., Ltd. Project No.: CCISE1907043 No.B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong,China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 7 of 24

Report No: CCISE190704306V01 6 Test results andMeasurement Data 6.1 Antenna requirement Standard requirement: FCC Part15 C Section 15.203 15.203 requirement: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. E.U.T Antenna: The EUT make use of an Induction coil antenna. Shenzhen ZhongjianNanfang Testing Co., Ltd. Project No.: CCISE1907043 No.B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong,China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 8 of 24

Report No: CCISE190704306V01 6.2 Radiated Emission Test Requirement: FCC Part15 C Section 15.225(a) and 15.209 Test Method: ANSI C63.10: 2013 TestFrequencyRange: 9 kHz to 1000MHz Test site: Measurement Distance: 3m(Semi-Anechoic Chamber) Receiver setup: Frequency Detector RBW VBW Remark 9kHz-150kHz Quasi-peak 200Hz 600Hz Quasi-peak Value 150kHz-30MHz Quasi-peak 9kHz 30kHz Quasi-peak Value 30MHz-1GHz Quasi-peak 120kHz 300KHz Quasi-peak Value Above 1GHz Peak 1MHz 3MHz Peak Value Limit: Frequency Limit (uV/m @30m) Limit (dBuV/m @3m) (Field strength of the 13.553MHz-13.567MHz 15848 124.0 fundamental signal) 13.410MHz-13.553MHz & 334 90.5 13.567MHz-13.710MHz 13.110MHz-13.410MHz & 106 80.5 13.710MHz-14.010MHz Remark: Per FCC part 15.31, when performingmeasurements at a closer distancethan specified, the results shallbe extrapolated to the specified distanceby either making measurementsat a minimum of two distances on atleast one radial to determine the properextrapolation factor or by using thesquare of an inverse linear distance extrapolationfactor (40 dB/decade). Limit: Frequency (MHz) Limit (uV/m @3m) Distance (m) (Spurious Emissions) 0.009-0.490 2400/F(kHz) 300 0.490-1.705 24000/F(kHz) 30 1.705-30 30 30 30-88 100 3 88-216 150 3 216-960 200 3 Above 1GHz 500 3 Test Procedure: a. The EUT was placed on the top of a rotating table 0.8 meters above the groundat a 3 meter semi-anechoic camber. The table was rotated 360 degrees todetermine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, whichwas mounted on the top of a variable-height antenna tower. c. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and thenthe antenna was tuned to heights from 1 meter to 4 meters and the rotatabletable was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Peak Detect Function and SpecifiedBandwidth with Maximum Hold Mode. f. If the emission level of the EUT in peak mode was 10dB lower than the limitspecified, then testing could be stopped and the peak values of the EUT wouldbe reported. Otherwise the emissions that did not have 10dB margin would bere-tested one by one using peak, quasi- peak or average method as specified andthen reported in a data sheet. Test setup: 9kHz-30MHz Shenzhen ZhongjianNanfang Testing Co., Ltd. Project No.: CCISE1907043 No.B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong,China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 9 of 24

Report No: CCISE190704306V01 30MHz-1GHz Above 1GHz Test Instruments: Refer to section 5.7 for details Test mode: Refer to section 5.3 for details Measurement Record: Uncertainty:±4.88 dB Test results: Pass Shenzhen ZhongjianNanfang Testing Co., Ltd. Project No.: CCISE1907043 No.B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong,China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 10 of 24

c c I s Report No: CCISE190704306V01 Measurement Data: Field Strength of fundamental signal: Product Name: POS Terminal Product Model: IM30 Test By: Mike Test mode: NFC Tx moade Test Voltage: AC 120/60Hz Environment: Temp: 24°C Huni: 57% 110Level (dBuVim) 100 so power 15225 umt 60 i w 40 M/—\M/'\Mh/\,_/\/\ J\\/ WeHrmvemtecrmemce) 20 1311 132 13.5 14.01 Frequency (MHz) Read&ntenna Cable Preamp Limit Over Freq Level Factor Loss Factor Level Line Limit Remark ______MHz dBu¥y dB/mdb — dB dBu¥/m dBu¥/m db — 1 13.560 34.28 —26.47 0.64 0.00 59.95 124.00 —64.05 Peak Remark: 1. _Final Level = Receiver Read level + Antenna Factor + Cable Loss — Preamplifier Factor. Shenzhen ZhongjianNantang Testing Co., Ltd. Project No.: CCISE1907043 No.B—C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bac‘an District, Shenzhen, Guangdong,China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 11 of 24

CCIS Report No: CCISE190704306V01 Spurious Emissions: Test frequency range: 9 kHz— 30 MHz Product Name: POS Terminal Product Model: IM30 Test By: Mike Test mode: NCF Tx mode Test Frequency: 150 kHz ~ 30 MHz Polarization: Vertical Test Voltage: AC 120/60Hz Environment: Temp: 24°C Huni: 57% 110l.\t§el (dBuVim) * 100} *\\5 PBALL_ so| ~bBhas, Fundamental signal Frequency (MHz) ReadiAnt enna Cable Preamp Limit Over Freq Level Factor Loss Factor Level Line Limit Remark ~— NHz MHz dBu¥ dBu¥ dB/mdb dB/m _dB dBu¥/m dBu¥/m —db — 1 0.0098 27.40 —25.60 0.02 0.00 53.32 108 —54. 68 Peak 2 0. 014 28.03 —25.85 0.04 0.00 53.72 104 —50. 59 Peak 3 0. 021 27. 53 —25.90 0.06 0.00 53.19 100 —47.57 Peak 4 0.031 23.09 —25.95 0.12 0.00 48.76 97 —48. 37 Peak 5 0. 156 23.30 —26.16 0.28 0.00 48.92 83 —34. 15 Peak 6 0. 495 15. 24 —26.30 0.45 0.00 40.89 52 —12. 03 Peak Remark: 1. Final Level =Receiver Read level + Antenna Factor + Cable Loss — Preamplifier Factor. 2. The emission levels of 9 kHz~150 kHz are background noise and very lower than the limit, not show in test report. Shenzhen ZhongjianNantang Testing Co., Ltd. Project No.: CCISE1907043 No.B—C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bac‘an District, Shenzhen, Guangdong,China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 12 of 24

c c I s Report No: CCISE190704306V01 Product Name: POS Terminal Product Model: IM30 Test By: Mike Test mode: NFC Tx moade Test Frequency: 150 kHz ~ 30 MHz Polarization: Horizontal Test Voltage: AC 120/60Hz Environment: Temp: 24°C Huni: 57% Level (dBuVim) 110 ’\\_\ 100 L1 SA 89 Fundamental signal 60) , FCjp 9K—30M 40 20 .009 .02 .05 A 2 $ 1 2 5 10 20 30 Frequency (MHz) Readéntenna Cable Preamp Limit Over Freq Level Factor Loss Factor Level Line Limit Remark """"""NHz dBu¥ dB/mdb — dB dBu¥/m dBu¥/m —db — 1 0.010 28.36 —25.80 0.03 0.00 54.09 107.08 —52.99 Peak 2 0.015 27.10 —25.85 0.04 0.00 52.179 103.81 —51.02 Peak 3 0.031 24.21 —25.95 0.12 0.00 49.88 97.06 —47.18 Peak 4 0.154 23.87 —26.16 0.27 0.00 49.48 83.14 —33.66 Peak 5 0. 317 20.90 —26.25 0.36 0.00 46.51 T76.82 —30.31 Peak 6 0.564 17.15 —26.30 0.50 0.00 42.85 51.88 —9.03 Peak Remark: 1. Final Level =Receiver Read level + Antenna Factor + Cable Loss — Preamplifier Factor. 2. The emission levels of 9 kHz~150 kHz are background noise and very lower than the limit, not show in test report. Shenzhen ZhongjianNantang Testing Co., Ltd. Project No.: CCISE1907043 No.B—C, 1/F. ., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bac‘an District, Shenzhen, Guangdong,China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 13 of 24

CCIS Report No: CCISE190704306V01 Test frequency range: 30MHz—1000MHz Product Name: POS Terminal Product Model: IM30 Test By: Mike Test mode: NFC Tx moade Test Frequency: 30 MHz ~ 1 GHz Polarization: Vertical Test Voltage: AC 120/60Hz Environment: Temp: 24°C Huni: 57% go Level (dBuVim) 70 60 FCC PART15 CLAS$ 8 50 40 30 20 10 30 50 100 200 500 1000 Frequency (MHz) Read&ntenna Cable Preanp Limit Over Freq Level Factor Loss Factor Level Line Limit Remark ''''''NHz dBu¥y dB/mdbdb dBu¥/m dBu¥/m —db — 1 45.375 44.42 12.28 1.29 29.86 28.13 40.00 —11.87 QP 2 86.503 47.31 9. 07 1.91 29.59 28.T0 40.00 —11.30 QP 3 117. 360 47.04 11.07 2.13 29.41 30.83 43.50 —12.67 QP 4 149.486 47.90 8.94 2.§1 29.22 30.13 43.50 —13.37 QP 5 242.525 46.77 12.42 2.82 28.58 33.43 46.00 —12.57 QP 6 654.232 36.80 19.78 3.89 28.77 31.170 46.00 —14.30 QP Remark: 1. Final Level= Receiver Read level + Antenna Factor + Cable Loss — Preamplifier Factor. 2. The emission levels of other frequencies are very lower than the limit and not show in test report. Shenzhen ZhongjianNantang Testing Co., Ltd. Project No.: CCISE1907043 No.B—C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bac‘an District, Shenzhen, Guangdong,China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 14 of 24

CCIS Report No: CCISE190704306V01 Product Name: POS Terminal Product Model: IM30 Test By: Mike Test mode: NFC Tx moade Test Frequency: 30 MHz ~ 1 GHz Polarization: Horizontal Test Voltage: AC 120/60Hz Environment: Temp: 24°C Huni: 57% 80Level (dBuVim) 70 60 4——————H———t————EECCD FCC PART1S CLAS$ 8 40 6 30 20 10 30 50 100 200 500 1000 Frequency (MHz) Read&ntenna Cable Preamp Limit Over Freq Level Factor Loss Factor Level Line Limit Remark ~ NBz dBu¥y db/mdb dB dBu¥/m dBu¥/m _ db 1 116.950 45.60 i1.11 2.13 29.41 29.43 43.50 —14.07 QP 2 186.441 49.56 10.18 2.77 28.93 33.58 43.50 —9.92 QP 3 243.377 46.02 12.42 2.82 28.58 32.68 46.00 —13.32 QP 4 301.422 44.51 13.63 2.94 28.45 32.63 46.00 —13.37 QP 5 502.940 41.07 18.21 3.64 28.96 33.96 46.00 —12.04 QP 6 848.056 33.21 22.60 4.20 28.01 32.00 46.00 —14.00 QP Remark: 1. Final Level= Receiver Read level + Antenna Factor + Cable Loss — Preamplifier Factor. 2. The emission levels of other frequencies are very lowerthan the limit and not show in test report. Shenzhen ZhongjianNantang Testing Co., Ltd. Project No.: CCISE1907043 No.B—C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bac‘an District, Shenzhen, Guangdong,China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 15 of 24

Report No: CCISE190704306V01 6.3 20dB Bandwidth Test Requirement: FCC Part15 C Section 15.215 (c) Test Method: ANSI C63.4:2014 Receiver setup: RBW=200Hz, VBW=300Hz, detector: Peak Limit: The fundamental emission be kept within atleast the central 80% of the permitted band Test Procedure: 1. According to the follow Test-setup, keep the relative position between the artificial antenna and the EUT. 2. Set the EUT to proper test channel. 3. Max hold the radiated emissions, mark the peak power frequency point and the -20dB upper and lower frequency points. 4. Read 20dB bandwidth. Test setup: Test Instruments: Refer to section 5.7 for details Test mode: Refer to section 5.3 for details Test results: Passed Measurement Data 20dB bandwidth (kHz) Limit (kHz) Results 0.600 11.2 Passed Note: For 13.56MHz, permitted Band is 14 kHz, so the Limit is 11.2 kHz. Shenzhen ZhongjianNanfang Testing Co., Ltd. Project No.: CCISE1907043 No.B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong,China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 16 of 24

Report No: CCISE190704306V01 Test plot as follows: * RBW 200 Hz Delta 1 [T1 ] * VBW 300 Hz -0.30 dB Ref 0 dBm * Att 20 dB SWT 125 ms 600.000000000 Hz 0 Offset 1 dB Marker 1 [T1 ] -48.56 dBm 13.559790000 MHz A -10 1 PK MAXH -20 LVL D1 -28.33 dBm -30 -40 1 1 D2 -48.33 dBm -50 6DB -60 -70 -80 -90 -100 Center 13.56 MHz 500 Hz/ Span 5 kHz Date: 24.JUL.2019 19:17:27 Shenzhen ZhongjianNanfang Testing Co., Ltd. Project No.: CCISE1907043 No.B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong,China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 17 of 24

CCIS Report No: CCISE190704306V01 6.4 Frequency Tolerance Test Requirement: FCC Part15 C Section 15.225 (e) Test Method: ANSI ©63.10: 2013 Receiver setup: RBW=200Hz, VBW=300Hz, span=14kHz, detector: Peak Limit: +0.01% of the operating frequency Test mode: Transmitting mode Test Procedure: Frequency stability V.S. Temperature measurement 1. The equipment under test was powered by a fresh battery. 2. RF output was connected to spectrum analyzer via feed through attenuators. 3. The EUT was placed inside the temperature chamber. 4. Set the spectrum analyzer RBW low enough to obtain the desired frequency resolution and measure EUT 20°C operating frequency as reference frequency. 5. Turn EUT off and set the chamber temperature to —20°C. After the temperature stabilized for approximately 30 minutes recorded the frequency. 6. Repeat step measure with 10°C increased per stage until the highest temperature of +50°C reached Frequency stability V.S. Voltage measurement 1. Set chamber temperature to 25°C. Use a variable DC power source to power the EUT and set the voltage to rated voltage. 2. Set the spectrum analyzer RBW low enough to obtain the desired frequency resolution and recorded the frequency. Reduce the input voltage to specify extreme voltage variation (+/— 15%) and endpoint, record the maximum frequency change. Test setup: Spectrum Analyzer ==I= ==I= ==I= aat E.U.T 1 Non—Conducted Table Ground Reference Plane Test Instruments: Refer to section 5.7 for details Test mode: Refer to section 5.3 for details Test results: Passed Shenzhen ZhongjianNanfang Testing Co., Ltd. Project No.: CCISE1907043 No.B—C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bac‘an District, Shenzhen, Guangdong.China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 18 of 24

CCIS Report No: CCISE190704306V01 Measurement Data: a) Frequency stability V.S. Temperature measurement Voltage Temperature < Frequency Tolerance Frequency Error Limit Results (Vdc) (C) (MHz) (%) (%) 20 0.082 0.0060 0.01 Pass —10 0.076 0.0056 0.01 Pass 0 —0.075 —0.0055 0.01 Pass 24.0 +10 0.081 0.0060 0.01 Pass — +20 —0.079 —0.0058 0.01 Pass +30 0.062 0.0046 0.01 Pass +40 0.079 0.0058 0.01 Pass +50 —0.042 —0.003 0.01 Pass b) Frequency stability V.S. Voltage measurement Temperature Voltage Frequency Tolerance Frequency Error Limit R — esults (°C) (Vde) (MHz) (%) (%) 10.2 —0.085 —0.0068 0.01 Pass 25 24.0 0.071 0.0054 0.01 Pass 55.2 0.092 0.0066 0.01 Pass Shenzhen ZhongjianNantang Testing Co., Ltd. Project No.: CCISE1907043 No.B—C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bac‘an District, Shenzhen, Guangdong,China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 19 of 24

Report No: CCISE190704306V01 6.5 Conducted Emission Test Requirement: FCC Part15 B Section 15.207 Test Method: ANSI C63.4:2014 TestFrequencyRange: 150kHz to 30MHz Class / Severity: Class B Receiver setup: RBW=9kHz, VBW=30kHz Limit: Limit (dBµV) Frequency range (MHz) Quasi-peak Average 0.15-0.5 66 to 56* 56 to 46* 0.5-5 56 46 0.5-30 60 50 * Decreases with the logarithm of the frequency. Test setup: Test procedure 1. The E.U.T and simulators are connected to the main power through a line impedance stabilization network (L.I.S.N.).It provide a 50ohm/50uH coupling impedance for the measuring equipment. 2. The peripheral devices are also connected to the main power through a LISN that provides a 50ohm/50uH coupling impedance with 50ohm termination. (Please refer to the block diagram of the test setup and photographs). 3. Both sides of A.C. line are checked for maximum conducted interference. In order to find the maximum emission, the relative positions of equipment and all of the interface cables must be changed according to ANSI C63.4: 2003 on conducted measurement. Test environment: Temp.: 23C Humid.: 56% Press.: 101kPa Measurement Record: Uncertainty: 3.28dB Test Instruments: Refer to section 5.7 for details Test mode: Refer to section 5.3 for details Test results: Pass Shenzhen ZhongjianNanfang Testing Co., Ltd. Project No.: CCISE1907043 No.B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong,China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 20 of 24

CCIS Report No: CCISE190704306V01 Measurement Data: Product name: POS Terminal Product model: IM30 Test by: Mike Test mode: NFC Tx mode Test frequency: 150 kHz ~ 30 MHz Phase: Line Test voltage: AC 120 V/60 Hz Environment: Temp: 22.5°C Huni: 55% Level (dBuV) 80, 70 so FCC PART15 B OP ~—L_ FCC PART15 B AV 50 Frequency (MHz) Read LISN Cable Limit Over Freq Level Factor Loss Level Line Limit Remark MHz dBu¥ dB dB dBu¥ dBu¥ 0.162 33.05 —0.44 10.77 43.38 65.34 —21.96 QP No — C to co —4 C Cn B C) ho + 0.234 27.58 —0.40 10.17§ 37.93 62.30 —24.31 QP 0.393 27.40 —0.37 10.72 37.15 57.99 —20. 24 QP 0.393 19.32 —0.37 10.72 29.67 41.99 —18. 32 Average 0.608 16.02 —0.38 10.77 26.41 46.00 —19. 59 Average 0.686 24.17 —0.38 10.77 34.56 56.00 —21.44 QP 0. 759 14.40 —0.38 10.80 24.82 46.00 —21.18 Average 1.000 11.02 —0.38 10.87 21.51 46.00 —24.49 Average 1.043 22.32 —0.38 10.88 32.82 56.00 —23.18 QP 1.619 10.18 —0.40 10.93 20.71 46.00 —25.29 Average 2.721 14.16 —0.43 10.93 24.66 46.00 —21. 34 Average 2.809 19.94 —0.44 10.93 30.43 56.00 —25.57 QP Notes: 1. An initial pre—scan was performed on the line and neutral lines with peak detector. 2. Quasi—Peak and Average measurement were performed at the frequencies with maximized peak emission. 3. _Final Level =Receiver Read level + LISN Factor + Cable Loss. Shenzhen ZhongjianNantang Testing Co., Ltd. Project No.: CCISE1907043 No.B—C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bac‘an District, Shenzhen, Guangdong,China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 21 of 24

CCIS Report No: CCISE190704306V01 Product name: POS Terminal Product model: IM30 Test by: Mike Test mode: NFC Tx mode Test frequency: 150 kHz ~ 30 MHz Phase: Neutral Test voltage: AC 120 V/60 Hz Environment: Temp: 22.5°C Huni: 55% 80Level (dBuV) 70 so FCC PART15 B OP 50\\\ FCC PART15 B AV 40 30 20 10 Trace: 25 Freguency (Mifé) Read LISN Cable Limnit Over Freq Level Factor Loss Level Line Limit Remark """MHz dBu¥y _ db _db dBu¥ dBu¥ —db 1 0.461 29.52 —0.6§5 10.74 39.61 56.67 —17.06 QP 2 0.461 23.11 —0.6§5 10.74 33.20 46.67 —13.47 Average 3 0.608 31.77 —0.64 10.77 41.90 56.00 —14.10 QP 4 0.647T 31.26 —0.64 10.77 41.39 56.00 —14.61 QP 5 0.647 23.42 —0.64 10.77 33.55 46.00 —12.45 Average 6 0.727 30.18 —0.64 10.78 40.32 56.00 —15.68 QP 1 0.783 21.71 —0.64 10.81 31.88 46.00 —14.12 Average 8 0.871 19.34 —0.63 10.83 29.54 46.00 —16.46 Average 9 1.049 29.83 —0.63 10.88 40.08 56.00 —15.92 QP 10 1.645 26.73 —0.66 10.93 37.00 56.00 —19.00 qP 11 1.645 19.27 —0.66 10.93 29.54 46.00 —16.46 Average 12 2.824 17.27 —0.67 10.93 27.53 46.00 —18.47 Average Notes: 1. An initial pre—scan was performed on the line and neutral lines with peak detector. 2. Quasi—Peak and Average measurement were performed at the frequencies with maximized peak emission. 3. _Final Level =Receiver Read level + LISN Factor + Cable Loss. Shenzhen ZhongjianNantang Testing Co., Ltd. Project No.: CCISE1907043 No.B—C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bac‘an District, Shenzhen, Guangdong,China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 22 of 24

Report No: CCISE190704306V01 7 Test Setup Photos Radiated Emission 9kHz-30MHz 30MHz-1000MHz Shenzhen ZhongjianNanfang Testing Co., Ltd. Project No.: CCISE1907043 No.B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong,China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 23 of 24

Report No: CCISE190704306V01 Conducted Emission 8 EUT Constructional Photos Reference to the test report No. CCISE190704301 ------End of report------ Shenzhen ZhongjianNanfang Testing Co., Ltd. Project No.: CCISE1907043 No.B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road, Bao’an District, Shenzhen, Guangdong,China Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 24 of 24


Document Created: 2019-09-06 21:16:58
Document Modified: 2019-09-06 21:16:58
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC