SAR report part 2

FCC ID: V5PD200V4

RF Exposure Info

Download: PDF
FCCID_3223792

Calibration Laboratory of \\‘\Q//"/ Schweizerischer Kalibrierdienst Schmid & Partner iia?-%m& Service suisse d‘étalonnage Engineering AG + x Servizio svizzero di taratura x s x a Zeughausstrasse 43, 8004 Zurich, Switzerland xL—Soy$ w Swiss Calibration Service ulutuls® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary DAE data acquisition electronics Connector angle information used in DASY system to align probe sensor X to the robot coordinate system. Methods Applied and Interpretation of Parameters e DC Voltage Measurement: Calibration Factor assessed for use in DASY system by comparison with a calibrated instrument traceable to national standards. The figure given corresponds to the full scale range of the voltmeter in the respective range. e Connector angle: The angle of the connector is assessed measuring the angle mechanically by a tool inserted. Uncertainty is not required. e The following parameters as documented in the Appendix contain technical information as a result from the performance test and require no uncertainty. DC Voltage Measurement Linearity: Verification of the Linearity at +10% and —10% of the nominal calibration voltage. Influence of offset voltage is included in this measurement. Common mode sensitivity: Influence of a positive or negative common mode voltage on the differential measurement. Channel separation: Influence of a voltage on the neighbor channels not subject to an input voltage. AD Converter Values with inputs shorted: Values on the internal AD converter corresponding to zero input voltage Input Offset Measurement. Output voltage and statistical results over a large number of zero voltage measurements. Input Offset Current: Typical value for information; Maximum channel input offset current, not considering the input resistance. Input resistance: Typical value for information: DAE input resistance at the connector, during internal auto—zeroing and during measurement. Low Battery Alarm Voltage: Typical value for information. Below this voltage, a battery alarm signal is generated. Power consumption: Typical value for information. Supply currents in various operating modes. Certificate No: DAE4—1386_Jul16 Page 2 of 5

DC Voltage Measurement A/D — Converter Resolution —nominal High Range: 1LSB = 6.4uV , full range =. —100...+300 mV Low Range: 1LSB = 6inV , full range = —1....... +3mV DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Calibration Factors KX ¥ Z High Range 404.512 £.0.02% (k=2) 404.603 + 0.02% (k=2) ‘404.126 + 0.02% (k=2) Low Range 4.02176 + 1.50% (k=2) 4.01405 + 1.50% (k=2) 4.01423 £ 1.50% (k=2) Connector Angle Connector Angle to be used in DASY system 203.5 °+1 ° Certificate No: DAE4—1386_Jul16 Page 3 of 5

Appendix (Additional assessments outside the scope of SCS0108) 1. DC Voltage Linearity High Range Reading (uV) Difference (uV) Error (%) Channel X +Input 199996.01 —0.60 —0.00 Channel X + Input 20002.59 0.57 0.00 Channel X — Input —19998.67 1.71 >0.01 Channel Y¥ + Input 199996.62 ~0.22 —0.00 Channel Y¥ +input 20000.89 —1.13 —0.01 Channel Y —Input —20000.90 —0.54 0.00 Channel Z + Input 199997.61 0.99 0.00 Channel Z + Input 19999.51 —2.37 —0.01 Channel Z —Input —20001.96 —1.40 0.01 Low Range Reading (uV) Difference (uV) Error (%) Channel X + Input 2002.92 0.82 0.04 Channel X + Input 202.39 0.07 0.03 Channel X — Input —197.72 —0.16 0.08 Channel Y¥ + input 2002.74 0.95 0.05 Channel Y + Input 201.78 —0.26 —0.13 Channel Y —Input —198.29 —0.48 0.24 Channel Z + Iinput 2002.23 0.55 0.03 Channel Z + Input 200.66 —~1.40 —0.69 Channel Z — Input —199.39 ~1.51 0.76 2. Common mode sensitivity DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Common mode High Range Low Range Input Voltage (mV) Average Reading (uV) Average Reading (uV) Channel X 200 ~15.11 —17.01 — 200 18.64 16.95 Channel Y 200 —8.25 —9.19 — 200 8.39 8.13 Channel Z 200 —7.20 —6.34 — 200 3.33 3.76 3. Channel separation DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Input Voltage (mV) Channel X (uV) Channel Y (uV) Channel Z (uV) Channel X 200 — 5.13 —3.37 Channel Y 200 8.77 — 5.77 Channel Z 200 8.45 7.08 — Certificate No: DAE4—1386_Juli16 Page 4 of 5

4. AD—Converter Values with inputs shorted DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec High Range (LSB) Low Range (LSB) Channel X 16014 14906 Channel Y 16071 16958 Channel Z 16059 12850 5. Input Offset Measurement DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Input 10MQ Average (uV) min. Offset (uV) max. Offset (uV) Std. l?:‘\l/;ation Channel X 0.02 —0.91 0.66 0.27 Channel Y —0.17 ~2.00 0.82 0.39 Channel Z —3.10 —3.84 —1.49 0.38 6. Input Offset Current Nominal Input circuitry offset current on all channels: <25fA 7. Input Resistance (Typical values for information) Zeroing (kOhm) Measuring {(MOhm) Channel X 200 200 Channel Y 200 200 Channel Z 200 200 8. Low Battery Alarm Voltage (Typical values for information) Typical values Alarm Level (VDC) Supply (+ Veoc) +7.9 Supply (— Veo) —7.6 9. Power Consumption (Typical values for information) Typical values Switched off (mA) Stand by (mA) Transmitting (mA) Supply {(+ Vee) +0.01 +6 +14 Supply (— Veoc) —0.01 —8 —9 Certificate No: DAE4—1386_Jult6 Page 5 of 5

6(9», in Cotaberaton nin «_ d wBwet st TTL 2.3 5 —p—e %cm«s"“ causmanon Lasoratory cxusmaon Add NoiS1 Xuevizn Rod, in Diavic Helin, 10019 Ching ..m. eP Sisltin Thcersenomnart recasioentinam Enal: ctl@dimtlcon Uite/ineihintin Clent Auden Cartificate No: 216—97054 CALIBRATION CERTIFICATE | ovieet exsove — siasre | Gattration Procecure(s) meenien Callbration Procedures for Dosimetrc E—feld Probes Callbration date May 11, 2016 This callratin Gertficate dacuments the traceabiity to natlonal standards, which realize the physical uns of measurements(S). The measurements and the uncertaintes with confidence probabilty are given on the folowing pages and are part of the certficate All caltbratons have been conducted in the clased laboratory faciiy: environment temperatire@zs3)e and humidity=70% Galioraion Equiament used (M&TE crtical fr calbration) Prmary Sandaras D# Gal Date(Galbraled byGenticate No) Scheduled Gatbraton Power Meter NRPZ 101010 0i—Ju—15 (CTTL, No JisXOi250) Jun—t5 Power sensor NRP—201. 101547 O1—Ju—15 (GTTL, No J16X04258) Jun—16 | Power sensor NRP—201 101548 01—Ju—15 (CTTL, No JtsX0ez5e) Jun—t6 | Referencet0dBAttenator 18N60W—1008 13—Mar—16(CTTLNo J1éx01547) Marts Reference20dBAtenuator 1BN5OW—204B 13—Mar—18(CTTL, NoJ1GX01548) Marto Reference Probe EX3DVé SN 3617 26—Aug—18(GPEAGNo EXG—3017_Aug1) Aug—t ones sN 13 21—Jan—16(SPEAG, NoDAEA—1381_Jant) Jan 17 Secondary Standards ID# Cal Date(Calibrated by, Gertfate No.) Scheduled Calbration SignalGeneratorMG3700A 6201052605 01—Ju18 (CTTL, No.J1$X04258) Jun—16 Network Analyzer ESO71G | MY410G73 26—an—16 (CTTL, NoJ1EX00804) dan 17 Name Function Sgnaure Galibrated by va zZongying SAR Test Engineer éfifie) Reviewed by l Dianyuen SAR Project Leader o m i Aporoved by Lu Bingsong Depuly Director o the laboratory i’g My Issued: May 193, ois This calibration certicate shall not be reproduced except in fullwihout writen approval of the laboratory Certiicate No: 216—97054 Page t of n

causrmmon tasoratory Add: No$1 Xoevan Road,tnianDiic, eling, 100191 China enemomnant rcoreloemoisman ctactiantson ifhowtintion Glossary: Ts tissue simulating liguid NORtfcyz senstily in free space ComyF sensitviy in TSL / NORMxx.e bor lode compression point or crestfactor(1/duty_cycle) of the RF signal ABco modulation dependent Incarization parameters Polariation ® @ rotation around probe axis Polariation 0 8 rotation around an axisthat is i the plane normal to probe axis (at measurement center), i 8=0 is normal to probe axis Connector Angle information used in DASY system to align probe sensor X to the robot coordinate system Calibration is Performed According to the Following Standards: a) IEEE Sid 1828—2013, ‘IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specitc Absorption Rate (SAR) in the Human Head from Wreless Communications Devices: Measurement Techniques®, June 2013 ) IEC 62209—1, ‘Procedure o measure the Specifc Absorption Rate (SAR) for hand—held devices used in close proximiy to the ear (requency range of 300Mz to 3GHz), February 2005 c) 1EC 62200—2, "Procedure to determine the Specifc Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (fequency range of 30 Miz to 6 GHz)°, March 2010 ) KDB 8656B4, ‘SAR Measurement Requirements for 100 MHz to 6 GHz" Methods Applied and Interpretation of Parameters: + NORMicy;z: Assessed for E—feld polarization 0=0 (fS900MHz in TEN—cell f> 1800MFz: waveguide}. NORMxy;z are onl intermediate values, e.,the uncertainties of NORNy.z does not effect the E"—ffeld uncertainty inside TSL (see below ConvF) + NORMMxy.z NORM.y.z" frequency_response (see Frequency Response Chart. This Inearization is implemented in DASY4 Software versions laterthan 4.2.The uncertainy ofthe frequency response i included in the stated uncertainty of Conve. * DOPryz: DCP are numericalIinearization parameters assessed based on the data of power sweep (no uncertainty required). DCP does not depend on frequency nor madia. + PAR: PAR is the Peak to Average Ratio that is not callbrated but determined based on the signal characteristics. * Auiz Beyce; Coyce:VRy:2:A,8.0 are numericalInearization parameters assessed based on the data of power sweep for specifc modulation signal. The parameters do not depend on frequency nor media. VR is the maximum callration range expressed in RMS vaitage across the diode * ConvE and Boundary Effect Paramefers: Assessed in flat phantom using E—field (or Temporature Transfer Standard for 800MH) and inside waveguide using analytcalfeld distrbutions based on power measurements forf »800MFiz. The same setups are used for assessment of the parameters applied for boundary compensation (alpha, depth) of which typical uncertainty valued are given These parameters are used in DASY4 software to improve probe accuracy close to the boundary. The sensitity in TSL corresponds to NORMy,z" Conv: whereby the uncertainty cortesponds to that given for ConvF. A fequency dependent GonvE is used in DASY version 4.4 and higher which allows extending the valdty from:50VHz tos100Miz. + Spherical sotropy (3D deviation from isotrapy): n feld oflow gradients realized using a fat phantom exposed by a patch antenna. + Sensor Offset:The sensor offset corresponds to the offset of viual measurement center from the probe ti(on probe axis) No tolerance required + ConnectorAngle: The angle is assessed using the information gained by determining the NORM« (no uncertainty required) Centeate No: 210—97084 Page2of 11

In C Ileb<! atio wi - TTL!....J? e a 9_ _ CAUBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86­10­62304633­2218 Fax: +86­10­62304633­2209 E­mail: cttl@chinattl.com Http://www.chinattl.cn Probe EX3DV4 SN: 3578 Calibrated: May 11, 2016 Calibrated for DASY/EASY Systems (Note: non­compatible with DASY2 system!) Certificate No: Z16­97054 Page 3 of 11

in Cotaberatonw TTL a causrnon tasoratory Add No.S1 uyon Rond, HaidanDi Reling, 100191 China ece doamoinantd recoveimidieisante E—malictladhinadcon Hinlicstinatles DASY/EASY — Parameters of Probe: EX3DV4 — SN: 3578 Basic Calibration Parameters SensorX [ Sensor Y SensorZ Une (ke2) | Norm(uV¥im})® oat o37 o44 +108% bCP(mV)® 1054 | 1000 123 Modulation Calibration Parameters UI | Communication *A Is ¢ o Ive Une® System Name aB aBipy a8 mV (ke2) o \ cw x loo Joo |io 000 _|1837 _ 126% y loo loo _li0 1690 _ z joo 00 10 1896 _\ The reported uncertainty of measurement is stated as the standard uncertainly u«( Measurement mulipled by the coverage factor k=2, which for a normal distrbution Corresponds to a coverage probabiity of approximately 95%. AThe unsertainties oNorm X, Y Z do not affect the E—feld uncertaintyInside TSL (see Page 5 and Page 6) * Numerical Inearzation parameter uncertanty not required * Uncertainy is determined using the max. devition from Iinear response agplying rectangular cistibution and is expressed forthe sauare of tfeld value Cenifiate No: 16—97084 Pagecofnn

In Collabo atio • , =rTL!....J' e a 9_ _ CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86­10­62304633­2218 Fax: +86­10­62304633­2209 E­mail: cttl@chinattl.com Hllp:l/www.chinattl.cn DASY/EASY - Parameters of Probe: EX3DV4 - SN: 3578 Calibration Parameter Determined in Head Tissue Simulating Media Relative Conductivity G Depth G Unct. f [MHzf ConvF X ConvF Y ConvF Z Alpha Permittivity F (81m) F (mm) (k=2) 750 41.9 0.89 9.65 9.65 9.65 0.40 0.80 ±12% 835 41.5 0.90 9.48 9.48 9.48 0.13 1.68 ±12% 900 41.5 0.97 9.40 9.40 9.40 0.20 1.28 ±12% 1750 40.1 1.37 8.35 8.35 8.35 0.18 1.49 ±12% 1900 40.0 1.40 7.99 7.99 7.99 0.18 1.50 ±12% 2000 40.0 1.40 7.99 7.99 7.99 0.17 1.58 ±12% 2300 39.5 1.67 7.77 7.77 7.77 0.40 0.82 ±12% 2450 39.2 1.80 7.28 7.28 7.28 0.46 0.83 ±12% 2600 39.0 1.96 7.21 7.21 7.21 0.49 0.81 ±12% 3500 37.9 2.91 7.07 7.07 7.07 0.40 1.10 ±13% 5200 36.0 4.66 5.42 5.42 5.42 0.40 1.50 ±13% 5300 35.9 4.76 5.22 5.22 5.22 0.39 1.40 ±13% 5500 35.6 4.96 4.99 4.99 4.99 0.40 1.40 ±13% 5600 35.5 5.07 4.75 4.75 4.75 0.42 1.45 ±13% 5800 35.3 5.27 4.82 4.82 4.82 0.45 1.45 ±13% c Frequency validity of ±100MHz only applies for DASY v4.4 and higher (Page 2), else it is restricted to ±50MHz. The uncertainty is the RSS of ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band. FAt frequency below 3 GHz, the validity of tissue parameters (E and 0) can be relaxed to ±10% if liquid compensation formula is applied to measured SAR values. At frequencies above 3 GHz, the validity of tissue parameters (E and 0) is restricted to ±5%. The uncertainty is the RSS of the ConvF uncertainty for indicated target tissue parameters. G Alpha/Depth are determined during calibration. SPEAG warrants that the remaining deviation due to the boundary effect after compensation is always less than ± 1% for frequencies below 3 GHz and below ± 2% for the frequencies between 3­6 GHz at any distance larger than half the probe tip diameter from the boundary. Certificate No: Z16­97054 Page 5 of 11

in Cotaberatonwn TTL a Causrimon tasoratom Add:NoS1 Xuuan Road,Haidin Disict Belin, 10019 Chia To oo nemienaerit raeioenoienare Emil:otlachinatl on Iiwncatine DASY/EASY —— Parameters of Probe: EX3DV4 — SN: 3578 Calibration Parameter Determined in Body Tissue Simulating Media [ ‘Conductvity | T. Deptn® Unct. | 1 uk c (Sim)" ConvF X ConvFY ConvE 2 Alpha e {mem) _| (ee2) ) 750 o.96 osi | sst | s o4o os5 412% | sas o7 ass ass ass | ons is1 _| £12% [_s00 105 947 oa7 o4r | ons 144| £12% 1750 140 s02 s02 aor | ons 167| +12% ) 1900 182 7.78 778 77e | 016 178 412% | 2000 152 70 770 770 ois 230 +12% 2300 ts1 _| Tss | 7e Tes oss os0 £12% [_2450 ies _| 7a1 7a1 7a1_| on | osr a12% 2600 216 7i7 717 7iz oso | aso +12% ) 3600 a31 sar |_6a7 ear osi 110 | £13% ) s200 530 ass _|_ass a9s oso iso a13% saco sa2 a7s a7s a7s oso 141| £13% 5500 ss a40 440 440 oss 135 |£19% 5eoo s77 430 a30 130| oso 185 a19% (_seoo 600 a42 a42 «42 oss 146 a13% | © Frequency vaidty of +100z only applies or DAGY vi.4 and higher (Page 2), else i is resticted to £50MHz. The uncertiny is the RSS of GonvE uncertaityatcalbration frequency and the uncertaityfor th incicated requency band "Atfrequency below 3 GHz, the valdty f ssue parameters (and 0) can be relaxed to +10% i quid compensation formula is appled to measured SAR values. A frequencies above 3 GHiz,the valdty of ssue parameters (c and 0)is restrted to +5%. The uncertainy is tRSS ofthe Conv® uncertintyfrinicated targa touue parameters ®AlphaiDepth are determined durig caltration. SPEAG warrantsthatthe remaining deviation due t the baundary affect attr compensaton is alrays les than + 19 fo requencias below 3 GHiz and below + 2% for the feauencies between 3.6 GHiz at any ditance largerthan halfthe probe tp ciamete rom the boundary Certifeate No: Z16—97054 Pagesof i1

@ in Co»ubormnewm 5 causemon asoratomy Add NS Xuevin Rod, itan Divis Being,100191 Chima o iosasieenaais reconioamoieisante Eonlachinatlcom Horisnwsenhinenisn Frequency Response of E—Field (TEM—Cell: ifi110 EXX, Waveguide: R22) 15 14 Frequency response (normalized) 13 12 11 10 oe 0.8 0.7 as a54 i t r r i t o soo 1000 1500 2000 2500 3000 E3 f [MHz] z. Tew fHe] * Uncertainty of Frequency Response of E—field: £7.5% (k=2) Cenifiene No: 21697084 Pagerof i1

infospomniznn <TTL a iemonastecon Add: NoS1 Xueymn Rod,Laitan Ditic, Being,100191 China Te ueocmosmant reloenomnare E—mal:n@stinaticon Hinthinectintion Receiving Pattern (®), 0=0° 1=600 MHz, TEM f=1800 MHz, R22 s« &$ un f.,.., iovrtT H omm n g—pugopiret eersemicg hivragcgss & «s ts 4 T T & I & m % . Roll 100Mz so0liz 1800btz + 2800ubt! Uncertainty of Axial Isotropy Assessment: £0.9% (k=2) Cenifcate No: 16—97054 Pagesof11

in Cotaboraton win TTL s p e a q causramon Lasorarofy Add: No1 Xveimn Road,Haitan Disc. Btin, 10019 China receteoamounani recersnamoimane Enail ctl@dtiartcon Hmihnosinats Dynamic Range f(SARneaq) (TEM cell, £= 900 MHz) 3 $ § ® %& £ SARImW/om‘] Eliinotcompensated ~~ compensted 1 $ ow a uie nnt t geg t 0n the e e yeese6n" && * % + ® % ® w " % to e nrsAva\W/cm 1 ‘® —not compensated compensated Uncertainty of Linearity Assessment: £0.9% (k=2) CenifcatNo: 216—97034 Pageoof11

r\"L in cummemm § Add No S1 Xuevim Rod, aidan Divics Reing, 100191 China Tiaeioemoimart receeivenbienarh Enallctl@chinalcon tihnchination Conversion Factor Assessment 1=900 MHz, WGLS R9(H_convF) f=1750 MHz, WGLS R22(H_convF) 1| aw 12 os as aa or to ow m on o on on Uncertainty of Spherical Isotropy Assessmer Cenifea No: 216—97054 Page ioi1

in eonaoor!it"') _TTL L..P e a 9_ _ ­­ CAUBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86­10­62304633­2218 Fax: +86­10­62304633­2209 E­mail: cttl@chinattl.com Http://www.chinattl.cn DASY/EASY - Parameters of Probe: EX3DV4 - SN: 3578 Other Probe Parameters Sensor Arrangement Triangular Connector Angle (0) 165.9 Mechanical Surface Detection Mode enabled Optical Surface Detection Mode disable Probe Overall Length 337mm Probe Body Diameter 10mm Tip Length 9mm Tip Diameter 2.5mm Probe Tip to Sensor X Calibration Point 1mm Probe Tip to Sensor Y Calibration Point 1mm Probe Tip to Sensor Z Calibration Point 1mm Recommended Measurement Distance from Surface 1.4mm Certificate No: Z16­97054 Page 11 of 11


Document Created: 2017-12-19 04:28:51
Document Modified: 2017-12-19 04:28:51
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC